blood pattern analysis

Blood Pattern Analysis

Pre-Lab Information

Properties of Blood

• 8% of total body weight• 5-6 liters of blood for males• 4-5 liters of blood for females• 40% blood volume loss, internally or

externally required to produce death.• 1.5 L loss will cause incapacitation.• A cut vein or artery will result in a loss

of ½ L per minute.

Injuries, Death and Blood

• Dead people do not bleed.

• If a body part is struck with an object the first blow will not cause blood spatter.

• Spatter occurs after the first blow when the wound begins to bleed.

SURFACE TENSION

• The elastic like property of the surface of the liquid that makes it tend to contract, caused by the forces of attraction between the molecules of the liquid.

• The cohesive forces tend to resist penetration and separation.

Categories of Bloodstains

• PASSIVE

• TRANSFER

• PROJECTED

TRANSFER BLOODSTAINS

• A transfer bloodstain is created when a wet, bloody surface comes in contact with a secondary surface.

TRANSFER STAINS SUBDIVISIONS

• CONTACT BLEEDING

• SWIPE OR SMEAR

• WIPE

• SMUDGE

PASSIVE BLOODSTAINS

• Passive bloodstains are drops created or formed by the force of gravity acting alone.

PASSIVE PATTERNS

• DROPS

• DRIP PATTERNS

• POOLS

• CLOTS

TARGET SURFACE TEXTURE

• Bloodstains can occur on a variety of surfaces, such as carpet, wood, tile, wallpaper, clothing, etc.

• The type of surface the blood strikes affects the amount of resulting spatter including the size and appearance of the blood drops.

TARGET SURFACE TEXTURE

• Blood droplets that strike a hard smooth surface, like a piece of glass, will have little or no distortion around the edge.

TARGET SURFACE TEXTURE

• Blood droplets that strike linoleum flooring take on a slightly different appearance. Notice the distortion (scalloping) around the edge of the blood droplets.

TARGET SURFACE TEXTURE

• Surfaces such as wood or concrete are distorted to a larger extent. Notice the spines and secondary spatter present.

LARGE VOLUMES OF BLOOD

• Patterns created by same volume of blood from the same source to target distance.

DRIPPED BLOOD

SPILLED BLOOD

PROJECTED BLOODThrough Syringe

PROJECTED BLOOD

• Projected bloodstains are created when an exposed blood source is subjected to an action or force, greater than the force of gravity. (Internally or externally produced.)

PROJECTED BLOOD

• The size, shape, and number of resulting stains will depend, primarily, on the amount of force utilized to strike the blood source.

ARTERIAL SPURT/GUSH

• Bloodstain patterns resulting from blood exiting the body under pressure from a breached artery.

ARTERIAL SPURT/GUSH

CAST-OFF STAINS

• Blood released or thrown from a blood-bearing object in motion.

CAST-OFF STAINS

IMPACT SPATTER

• Blood stain patterns created when a blood source receives a blow or force resulting in the random dispersion of smaller drops of blood.

LOW VELOCITY IMPACT SPATTER

• Gravitational pull of up to 5 feet/sec

• Relatively large stains 4 mm in size and greater.

LOW VELOCITY IMPACT SPATTER

MEDIUM VELOCITY IMPACT SPATTER

• Force of 5 to 25 feet/sec.

• Preponderant stain size 1 to 4 mm in size.

MEDIUM VELOCITY IMPACT SPATTER

HIGH VELOCITY IMPACT SPATTER

• Force of 100 feet/sec and greater.

• Preponderant stain size 1 mm in size and smaller.

• Mist like appearance.

HIGH VELOCITY IMPACT SPATTER

DIRECTIONALITY OF BLOODSTAINS

• When a droplet of blood strikes a surface perpendicular (90 degrees) the resulting bloodstain will be circular.

• That being the length and width of the stain will be equal.

DIRECTIONALITY OF BLOODSTAINS

• Blood that strikes a surface at an angle less than 90 degrees will be elongated or have a tear drop shape.

• Directionality is usually obvious as the pointed end of the bloodstain (tail) will always point in the direction of travel.

DIRECTIONALITY OF BLOODSTAINS

DIRECTIONALITY OF BLOODSTAINS

IMPACT ANGLE DETERMINATION

• The angle of impact is the acute angle formed between the direction of the blood drop and the plane of the surface.

• By utilizing trigonometric functions its possible to determine the impact angle for any given blood droplet.

• SIN < = opp (a)/hyp (c)

IMPACT ANGLE DETERMINATION

IMPACT ANGLE DETERMINATION

• By accurately measuring the length and width of a bloodstain, the impact angle can be calculated using the Sine formula

IMPACT ANGLE DETERMINATION

IMPACT ANGLE DETERMINATION

• SIN < = width (a) 1.5 cm/length (c) 3.0 cm

• 0.5 = SIN <• < = 30 degrees.

POINT OF CONVERGENCE AND ORIGIN DETERMINATION

• The common point, on a 2 dimensional surface, over which the directionality of several bloodstains can be retraced.

• Once the directionality of a group of stains has been determined, it’s possible to determine a two dimensional point or area for the group of stains.

POINT OF CONVERGENCE AND ORIGIN DETERMINATION

POINT OF CONVERGENCE AND ORIGIN DETERMINATION

POINT OF CONVERGENCE AND ORIGIN DETERMINATION

VOIDS

• Void in otherwise uniform splatter - something blocked the blood spray

VOIDS