b44.1 manual preflight
Post on 28-Apr-2015
103 Views
Preview:
TRANSCRIPT
9/1
0
2:: Introduction
:: KIT Features
:: Additional Features
:: Other Helpful Items
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 B44.1. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustra-tions. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.
The Factory Team B44.1 is the next generation in a long line of race winning 10th scale 4wd buggies dating back to 2003. The B44 project came to life as a cooperative effort between Team Associated and J Concepts’ Jason Ruona and Brad Reelfs, culmi-nating with Team Associated driver Ryan Cavalieri winning the 2005 I.F.M.A.R. World Championships in Italy with the BJ4 World’s Edition. The production B44 Factory Team continued the winning ways with Jared Tebo winning the 2007 I.F.M.A.R. World Cham-pionship in Japan along with Ryan Maifield and Ryan Cavalieri in a 1-2-3 B44 podium sweep.
Team Associated designers optimized the B44.1 for the latest generation of racers using LiPo batteries and brushless motors. With the advent of this new technology, R/C cars are lighter and more powerful than ever. The B44.1 is geared for strictly LiPo batter-ies, with no cell slots in the chassis and a carbon fiber battery tray as standard equipment. The center section of the battery tray can be replaced with an optional (not included) ballast weight for more rearward weight bias. Motor installation and adjustment is a breeze thanks to the cam motor mount system. The blue aluminum rear hubs add durability and new camber link adjustment options. Lastly, the B44.1 comes with the latest JConcepts Punisher body and under tray.
Features in the B44.1 Factory Team:• 2.5mm updated carbon fiber chassis for LiPo batteries only• Carbon fiber LiPo battery tray with removable center section (*optional ballast weight req’d)• 3.5 mm front shock tower• Updated front top deck for more durability along with new antenna location• Cam motor mount set• Factory Team 0 degree aluminum rear hubs with oversize outer bearing.• Factory Team V2 dual-cap hard anodized shock bodies with threaded collars• V2 slipper assembly with high-rate spring • Factory Team Gold slipper pads• JConcepts Punisher body and under tray• Pro-Line M3 Holeshot 2.0 tires• Rear anti-roll bar included• Bleed-screw shock caps• TiN “Gold” shock shafts front and rear• Carbon fiber battery straps with thumb screws• 1/4” locking and 3/16” mini locking nuts
B44.1 F.T. Additional Kit Features:• Servo mounted 3mm closer to centerline • Chassis cut for additional ground clearance• Ball differential with light-weight outdrives • Dual-sided externally adjustable slipper clutch• CVA joints with pin retainer clips • Factory Team blue Titanium turnbuckles• Factory Team blue aluminum servo mounts • Factory Team blue aluminum wheel spacers• Factory Team blue aluminum shock bushings • Factory Team blue aluminum shock pivot balls• Ball-bearings steering bell cranks • Fully adjustable camber, and toe-in• Built in servo saver • Vertical ball end adjustment front & rear
• Silicone Shock Fluid (Refer to catalog for complete listings)• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife • FT Hex Wrenches (AE Part # 1541) • Needle Nose Pliers • Multi Tool (AE Part #7494)• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
3:: Table of Contents
:: Notes
This symbols indicates a special note or instruction in the manual.
!There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.
1....................Cover
2....................Introduction 3....................Table of Contents
4....................Front / Rear Differential Build
5....................Front Gearbox Build
6....................Rear Gearbox Build
7 - 8..............Steering and Center Battery Brace Build / Install
8 - 9..............Front End Build
9....................Rear End Build
10.................Slipper Build
11..................Center Bulkhead Mounts
11.................Front Top Deck Build
11-12..........Rear Top Deck Build
13.................Turnbuckles Build
13.................Front CVA Build
13-14..........Front Suspension Build
15.................Rear CVA Build
15 - 16.......Rear Suspension Build
16-17..........Rear Anti-Roll Bar Build
17.................Battery Tray and Side Body Mounts Build
18 - 19........Shocks Build
19 - 20........Servo Build
20.................Electronics Install
21 - 22........Body, Wheel, Tires Install
23 - 24.........Tuning Tips
25-33.........Catalog
34.................Notes
35.................Setup Sheet “Kit Setup”
36.................1:1 Hardware “Fold Out”
37.................Setup Sheet “Blank”
38.................Back Cover
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
4:: Front and Rear Differential Build - Step 1
:: Front and Rear Differential Build - Step 2
-1/8
-5/8
-1/4
-3/8
0
-1/4 -3/4
5/64” hex wrenchinstalled in diff bolt
Fully tightened
position
KitSetting
Trim any flashing material off of the
#2330 Locking t-nut ears!
!
Build twodiffs!
!
#65
88
blac
k gr
ease
3911Diff outdrive
shim
3976Diff outdrive
bearing
6574Thrust balls
6582Diff
spring
2330Locking
t-nut
6573Thrust
washers
6573Thrust screw
6909Diff
bearing
x6
x2
x6
x2
6909Diff
bearing
3914Bevel
diff gear
9734Diff
outdrive, long
9734Diff
outdrive, short
6579Diff
outdrive ring
6579Diff
outdrive ring
6581Diff balls
x12
#6591diff lube
#6591diff lube
#6591diff lube
5:: Front Gearbox Build - Step 1
:: Front Gearbox Build - Step 2
:: Front Gearbox Build - Step 3
6860FT 4-40x3/8”
shcs aluminum, blue
Align the gap in the pin retainer
to be opposite of the CVA pin.
Racer’s Tip:Try using only 1 drop of CA glue
to secure the pin retainer!
Trim flashing off back of gear. Align the slot in the pinion gear
with the pin!
!
!
#1597ca glue
39773/16x3/8”
bearing
3911Drivetrain
shim
x2
x2
x6
#6591
diff lube
#6588
black grease
9733Upper
transmission case
6299E-clip
3919Input shaft
pin
3903Shaft pinion
gear
7996CVA pin retainer
73814-40
setscrew
9761CVA input
shaft
7381CVA
coupler
9747CVA bone
center, front
9733Lower
transmission case
#6591
diff lube
1 drop!1 drop!
1 drop!
6:: Rear Gearbox Build - Step 1
:: Rear Gearbox Build - Step 2
:: Rear Gearbox Build - Step 3
39773/16x3/8”
bearing
3911Drivetrain
shim
x2
x2
6860FT 4-40x3/8”
shcsaluminum,
blue
#6591
diff lube
#6591
diff lube
#6588
black grease
x6
9733Upper
transmission case
6299E-clip3919
Input shaft pin
3903Shaft pinion
gear
7996CVA pin retainer
73814-40
setscrew
9761CVA input
shaft
7381CVA
coupler
9760CVA bone
center, rear
9733Lower
transmission case
Align the gap in the pin retainer
to be opposite of the CVA pin.
!
#1597ca glue
Align the slot in the pinion gear
with the pin!
!with the pin!
Racer’s Tip:Try using only 1 drop of CA glue
to secure the pin retainer!
1 drop!
1 drop!
1 drop!
7:: Steering and Center Battery Brace Build Step 1
:: Steering and Center Battery Brace Build Step 2
9746Steeringbearing
set
:: Steering and Center Battery Brace Build Step 3
1mm
9746Steeringbearing
set
6272Foam dust
cover
9630.030” washer
9743Spring
retainer
9743Steeringv-spacer
9743Servo saverupper
6277Ballstud
long, silver
x2
x2
x2
x2
x2
62924-40x3/8”
fhcs
9774B44.1 LiPo
chassis
9743Steering retainer column
9743Steering
retianer top
62924-40x3/8”
fhcs
69174-40x3/8”
bhcs
3874Black carrier
bushing
97445-40
locknut
9744Servo saver
spring
9743Servo saver
lower
6272Dust cover
foam6276
Ballstudshort, silver
9743Steering
rack
x2x2
x2
x2
9744Steering
post
x2
x2
Use the large hole bearings!
Use the small hole bearings!
!
!
8:: Steering and Center Battery Brace Build / Install Step 4
:: Front End Build - Step 1
:: Front End Build - Step 2
9715Front arm
9714Shock tower
mounts
96452-56x1/8”
bhcs
62924-40x3/8”
fhcs
62924-40x3/8”
fhcs
62924-40x3/8”
fhcs
6472Shock
mount nuts
9775B44.1 LiPobattery tray
9716Front innerhinge pin
44494-40x3/16”aluminum
locknut
9713Front
bulkhead
97654-40x7/16”
fhcs
x2
x2x2
x2
x2
x2
x2
#1596thread lock
9:: Front End Build - Step 3
:: Rear End Build - Step 1
:: Rear End Build - Step 2
69154-40x5/8”
fhcs
1780Shock
bushing
9703Front shock
tower
74134-40x3/4”
bhcs
9726Rear chassis
brace
96452-56x1/8”
bhcs6292
4-40x3/8”fhcs
9716Rear innerhinge pin
44494-40x3/16”aluminum
locknut
44494-40x3/16”aluminum
locknut
6936#4 washer
69174-40x3/8”
bhcs
69174-40x3/8”
bhcs
9718Front
bumper
9764Rear arm
9718Rear
bumper
9726Rear
chassisplate
97654-40x7/16”
fhcs
76734-40x5/16”
fhcs
x2x4
x2
x3
x2
x2x2
x2
x2
x2
x2
#1596thread lock
10:: Slipper Build - Step 1
:: Slipper Build - Step 2
:: Slipper Build - Step 3
x2
x2
Check slipperafter running!
Adjust as needed.
!
1654Solid pin
9742Slipper drive
cup
9742Slipper drivecup o-ring
1654Solid pin
9711Center bearing
insert7485FT V2
slipper hubs
73814-40
setscrew
Side view1 flange
9741Slipper nut
o-ring9740Slipper
nut
7486FT V2
slipper spring
9742Slipper drive
cup
9736Slipper shaft
9736Slipper spring
retainer
9711Center
bearing insert
9736slipper
drive cup spacer
79353/16x1/2”
bearing
9603Slipper
pad
965181T 48Pspur gear
79353/16x1/2”
bearing
x2
10mm
Side view2 flanges
#6588black grease
Rub black grease on o-ring before
install!
Insert #9741 Slipper nut o-ring all the way into the
#9740 Slipper nut be-fore installing the slipper nut to the slipper shaft!
!
!
11:: Center Bulkhead Mounts - Step 1
:: Front Top Deck Build - Step 1
:: Front Top Deck Build - Step 2 :: Rear Top Deck Build - Step 1
Key CVA bones in the slipper outdrives!
Set remaining motor mount pieces aside!
!
!
31113Antenna mount
9714Shock tower mount
9701Top deck
front
9719Body
mount
9709Center
bulkhead
9801FT cam motor mount
43342-56x5/16”
bhcs
69174-40x3/8”
bhcs
69174-40x3/8”
bhcs
6277Ballstud
long, silver
44494-40x3/16”aluminum
locknut9702
Top deckrear
6936Washers,
aluminum #4
x2
x2
x2
x2
Top deckfront
Body mount
x2
x29714Shock tower mount
bhcs
6917 x2x2
44494-40x3/16”aluminum
locknut
6936Washers,aluminum
#4
62924-40x3/8”
fhcs
62914-40x1/4”
fhcs
6277Ballstud
long, silver
x2
x2
x3
x262884-40x1/4”
bhcs
Slipper assembly
Install
#1596
thread lock
62924-40x3/8”
fhcs
x5#1596
thread lock
12:: Rear Top Deck Build - Step 2
:: Rear Top Deck Build - Step 3
:: Rear Top Deck Build - Step 4
74134-40x3/4”
bhcs1780Shock
bushing
62924-40x3/8”
fhcs
9719Body mounts
x2
x2
x2
69174-40x3/8”
bhcs
77384-40x7/8”
shcs
69254-40x1/2”
shcs
69174-40x3/8”
bhcs
69244-40x3/8”
shcs
69244-40x3/8”
shcs
9712Center
bulkhead cap
9704Shock tower
rear
9714Shock tower
mount
9729Wing mount(right, left) 4449
4-40x3/16”aluminum
locknut
x2
x2
x3
x2
x2
x4
x2
#1596thread lock
#1596thread lock
#1596thread lock
13:: Turnbuckles Build - Step 1
:: Front CVA Build - Step 1
:: Front Suspension Build - Step 1
Front Steering Link
Front Camber Link
Rear Camber Link
44494-40x3/16”aluminum
locknut
9722Steering
block(right, left)
6277Ballstud
long, silver
6272Foam dust
cover
x2
x2x2
x2
Align the gap in the pin retainer
to be opposite of the CVA pin.
!
SteeringBuild x2
Front CamberBuild x2
Rear CamberBuild x2
Build x2
1 drop!
7996CVA pinretainer
7381CVA cross
pin
7381CVA coupler
1406FT titaniumturnbuckles
2.00”
1406FT titaniumturnbuckles
2.00”
1404FT titaniumturnbuckles
1.77”
9748CVA axle
front
9747CVA bone
front
#65
88
blac
k gr
ease
39773/16x3/8”
bearing
x4
9751Bearing
crush tube
x2
Left Side
Left Side
Right Side
Right Side
7230Ball cups,
large
7230Ball cups,
large
7230Ball cups,
large
x2
x2
x2
67mm
60mm
64.5mm
#1597ca glue
14:: Front Suspension Build - Step 2
:: Front Suspension Build - Step 3
:: Front Suspension Build - Step 4
22214-40x7/16”
bhcs
7369Axle pin
9647Steering
block bushing
6272Dust cover
foam
9750Axle drive
hex
44494-40x3/16”aluminum
locknut
9720Caster block(right, left)
3983Ballstud
long, black
x2
x2
x2
x2x2
x4
x2
x4
Left Side
Left Side
Left Side
Left Side
Right Side
Right Side
Right Side
Right Side
96452-15x1/8”
bhcs
Build x2 (right and left side)
9716Hinge pin
set
Front camber
link
Front steering
link
Install x2 (right and left side)
Orient the notch to the left
throughout the car. It indicates
which end has the left hand threads!
!
15:: Rear CVA Build - Step 1
:: Rear Suspension Build - Step 1
:: Rear Suspension Build - Step 2
39773/16x3/8”
bearing
7381CVA coupler 7996
CVA pinretainer
9755CVA axle
rear
9872FT aluminum
hub tower(A)
9864FT aluminum
hub (0˚)
9754CVA bone
rear7381
CVA cross pin
6272Dust cover
foam
7933Crush tube
3983Ball stud
long (black)
x2
x2
x2
x2
x2
69324-40x5/16”
shcs
7935.187x0.50x.196
bearing
x4
x2
x2
1 drop!
Left Side
Left Side
Right Side
Right Side
Molded camber link tower “A” has standard holes, and optional “B” tower has “in-between” hole
options!
!
A
#6588
black grease
Align the gap in the pin retainer
to be opposite of the CVA pin.
!
Build x2 (right and left side)
Build x2 (right and left side)
#1597ca glue
Build x2
16:: Rear Suspension Build - Step 3
:: Rear Suspension Build - Step 4
:: Rear Anti Roll Bar Build - Step 1
73683/16”
axle shims
9608Rear axle
wheel spacer
31286Aluminum ballstud
washer, 1mm
9630.030” ballstud
washer
73691/16”
roll pins
96452-15x1/8”
bhcs
9716Hinge pin
set
8830Anti roll
bar pivots
97804-40x1/2” set screw
x2
x2
Add 1 shim hereif needed.
Build x2
8828Anti rollbar cups
Rear camber
link
8828Ball cup,
short
1mm
Install x2 (right and left side)
Install x2 (right and left side)
Orient the notch to the left
throughout the car. It indicates
which end has the left hand threads!
!
Build x2 (right and left side)
17:: Rear Anti Roll Bar Build - Step 2
:: Battery Tray and Side Body Mounts Build - Step 1
76734-40x5/16”
fhcs
62924-40x3/8”
fhcs
97454-40x.625”
setscrew
9706Battery
post
69514-40x1/8”setscrew
43342-56x5/16”
bhcs
9780Washer 9780
0.55” silver anti-roll bar
9775LiPo
battery tray
9719B44 bodymounts
x2
x4
x4
x4
x2
x2
x2
x2
x2
Trim side body mounts as shown
before installation!Threadlock all setscrews!
!!
Optional black anti-roll bar also
included!
!
#1596
thread lock
#1596thread lock
Install anti-roll bar into #8830 anti-
roll bar pivots until the bar is flush with the end of the pivot!
!
18:: Shocks Build - Step 1
:: Shocks Build - Step 2
:: Shocks Build - Step 3
6465Shock piston(#1)
6465Shock piston(#2)
6469Shock cap
o-ring
7484Shock
internal spacer
7484Shock
internal spacer
7475Front shock body0.89”
7479Rear shock body 1.18”
6469Shock cap
o-ring
9723FT shock
shaft gold0.80” 6417
FT shock shaft gold
1.02”
x46443Bleeder
shock cap(molded)
1777FT shock pivot ball
1777FT shock pivot ball
1777Shock eyelet
4187.030 nylon
washer
4187.030 nylon
washer1777Shock eyelet
Step 9-10
Step 8Step 6-7Step 4-5
Front Shock: 35 wt
Rear Shock: 30 wt
Step 2-3
5407O-ring
7484Lower shock
seal cap
7484Lower shock
seal cap
5407O-ring
6299e-clip
6299e-clip
x2
x2
x2x2
96452-56x1/8”
bhcs
x4Shock Bleeding Steps:1. Before assembly, get each bleed
screw and thread it 1-2 turns into the shock cap. This will make installation easier when you are bleeding your shocks.
2. Pull shock shaft down.3. Fill shock body 3/4 full with silicone
shock fluid.4. Slowly move the shock shaft up and
down to remove air from under the piston.
5. Wait for bubbles to come to surface.6. Fill shock body to top with silicone
shock fluid.7. Place a drop of oil in the cap and on
cap threads.8. Install cap (without bleed screw) and
tighten completely.9. Slowly compress shaft all the way to
bleed excess silicone shodk fluid out the hole in the cap (use rag around-shock to catch excess fluid).
10. Install 2-56 button head screw until snug while shaft is fully compressed (recommend using a high quality .050” wrench such as Factory Team
#1542).
Shock oilShock oil
Front, Build x2 Front, Build x2
Front, Build x2
Front, Build x2 Front, Build x2
Rear, Build x2
Rear, Build x2
Rear, Build x2
Rear, Build x2Rear, Build x2
#1105green slime
#1105green slime
19:: Shocks Build - Step 4
:: Shocks Build - Step 5
:: Servo Build - Step 1
7337Gold
washer
89007Servo horn
ring
3981Ballstud
.20” black,short
6272Dust cover
foam9180Servohorn
1779FT Servo mount
6472Shock
mount nut
6475Rear spring
cup
9724Front offset spring cup
6480Rear Spring,
Green, 1.90lb
6480Front Spring,Silver, 3.85lb
69254-40x1/2”
shcs
69254-40x1/2”
shcs
6472Shock
mount nut
x4
x2
x2
x2x2
x2x2
x2x2
x2
x2
x2
7336Servo
spacers
69174-40x3/8”
bhcs
Build two rear shocks
Build two front shocks
!!
Offset the servo horn by 5-10 degrees
(approximately one notch)! (approximately one notch)!Servo not included!
Servo screwnot included!
x2x2
Build two rear shocks
7416Shock collar o-ring
7416Shock collar
x4
x4
1.7mm
12mm
Use outside holein front arm!
Use inside holein rear arm!
!
!
20:: Servo Build - Step 2 :: Electronics Install - Step 1
:: Electronics Install - Step 3
:: Electronics Install - Step 2
LiPo batteries not included!
ESC not included!
Motor not included!
Receiver not included!
Pinion and setscrew not
included!
31531M3x6mm
bhcs
9803FT Motor
Mount Cam
x2
6338Antenna
tube & cap20.5m
x2
x2
1787FT body
clips, blue
98024-40x.100”
setscrew
9786Battery strap,
carbon fiber
See ESC manufacturer’s instructions for
wiring!
!
69254-40x1/2”
shcs
9802Steel
washer
9802FT Motor mountclamp
x2
x2
7911Servo Link
x262924-40x3/8”
fhcs
Set gear mesh!
Motor tabs should clear top deck!
!
!
Loosenmesh
Tightenmesh
21:: Body, Wheels, Tires Install - Step 1
:: Body, Wheels, Tires Install - Step 2
:: Body, Wheels, Tires Install - Step 2
Carefully apply tire adhesive to the tire bead on
both sides.Do one side at a time, allow it to
dry before gluing the other side!
!
97672.2” Wheel,
front
69538-32
LP steellocknut
9769Proline Holeshot 2.0
M3 compound w/ insert, front
x2
x2
x2
x2
x2
69528-32
locknut, steel
95892.2” Wheel,
rear
#1597
ca glue#1597
ca glue
9590Proline Holeshot 2.0
M3 compound w/ insert, rear
x2
Punisher undertray
by Jconcepts
Add hole
Add hole
Add hole
Slide undertray in between the
front bumper and the chassis!
!Trim along
lines!
!3mm or .125” holes on marks
22:: Body, Wheels, Tires Install - Step 3
:: Body, Wheels, Tires Install - Step 4
:: Body, Wheels, Tires Install - Step 5
Punisher body by
JConcepts
x2
x2
x2
9718Rear
bumper
76734-40 x 5/16”
fhcs
76734-40 x 5/16”
fhcs
6472nylon nut
1736FT body
clips, blue
1736FT body
clips, blue
9729Wing shims
9772High downforce
wing, 6.5”
Painting Tips:Body : Your B44.1 FT comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush) the paint to the inside of the body (prefferably dark colors first, lighter colors last).
NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you don’t, you candestroy the plastic body!!!!).
After painting, cut the body along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts and antenna!
Use the screw for the servo mount for the opposite side!
!
23:: Tuning TipsTips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.
Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change.
When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions.
Front Arm Hole:
The kit silver springs and outside front arm hole will work best in most cases. Moving the shock to the inside hole on the front arm requires you to add another down travel limiter to the front shocks, so there should be two down travel limit-ers in each shock. You should also change to a stiffer spring to account for the difference in leverage on the shock.
Front Ride Height:
The standard front ride height setting is 21mm. Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, raise or lower the shock collars as necessary until there is 21 mm gap from the bottom of the chassis to the ground.
Anti-Squat:
Anti-squat denotes the angle of the rear arms relative to the ground. Zero anti-squat means that the rear arms are flat, parallel with the ground. The kit setting is 2 degrees, and can be reduced to 1 degree by removing the included #4 washer underneath the arm mount. You can add another #4 washer so that there is two washers underneath the arm mount to get 3 degrees of anti-squat. Adding anti-squat tends to make the car “rotate” more in corners, but doesn’t handle as well through the bumps. 1 degree will be better in bumpy sections.
Rear Camber Link Length & # of Washers under Ballstud:
Changing the length of the camber link is considered a bigger step than adjusting the ballstud height on the rear chassis brace. Typically shortening the camber link (or lowering the ballstud) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ballstud) will give the rear more roll and more cornering grip. To raise the ballstud, remove washers from in-between the ballstud and upper deck. You should normally use the kit setting and only adjust the ballstud height
Differential:
Adjust the differential (AKA ‘diff’ for short) as noted in the assembly instructions. Adjusting the rear diff is not meant to be a tuning option. If you can hear the diff making a “barking” or “chirping” sound on jump landings or under acceleration, either your diff is set too loose or your slipper clutch is set too tight. The front diff can go out 1/16” turn to get more steering.
Slipper Clutch:
The assembly instructions give you a base setting for your clutch. To preserve the differentials, always start with the slipper on the loose side and slowly tighten the adjustment nut until it is set. To adjust the slipper, remove the body and insert a 2mm (or 5/64”) hex wrench through the center of the top deck (or through the bottom slot in the chassis). Then, grab both of the rear wheels and rotate forwards to tighten and backwards to loosen. As you spin the wheels, you’ll feel the motor click every ¼ of a wheel revolution. At the track, tighten or loosen the nut in 2 click increments until you hear only a faint slipping sound for 1-2 feet on takeoffs.
Front Camber Link Length & Number of Washers Under Ballstud:
Changing the length of the camber link is considered a bigger step than adjusting the ballstud height. Typically shortening the camber link (orlowering the ballstud) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ballstud) will give the front more roll and slower steering response. To raise the ballstud, remove washers from between the ballstud and upper deck.
Front Camber:
A good starting camber setting is –1 degrees. Use the included #1719 camber gage to set your camber. Positive camber, where the top of the tire is leaning out, is typically not recommended.
Front Toe-In:
Zero degree toe-in (tires pointing straight forward) is the setting that should be used in almost all track conditions. Occasionally you can increase turn in by adding a little toe-out (front of tires point slightly out). Front toe in is not a typical tuning adjustment used by The Team.
24:: Tuning Tips (cont.)Rear Hub Spacing:
You have 3 options for rear hub spacing, FORWARD, MIDDLE, & BACK. The kit setting is FORWARD, which provides the most rear traction and will be used most often. For improved handling in bumps or rhythm sections, try moving the hubs to MIDDLE or BACK. This can also make the car handle better in 180 turns.
Rear Anti-Roll Bar:
The #9780 B44 anti-roll bar kit (a.k.a. swaybar) allows you to add roll resistance to the rear end with minimal effect on handling over bumps and jumps. The anit-roll bar is very helpful when trying to tune the suspension. The black bar is the softest (.047” wire) and the silver (.055” wire) is the standard. It is popular to run a rear anti-roll bar in 4wd to help the car square up more out of turns.
Rear Arm Hole:
The inner hole in the arm tends to work the best over the bumps and jump sections. Changing to the outer hole in the rear arm will tend to make the rear end feel more “locked in” and less responsive. Making this change to the outer hole requires you to remove the downtravel limiters from the rear shocks.
Setup Sheets:
Most often, the best way to get your car handling right is to go to our website www.rc10.com and click on the links to Setup Sheets, then RC10B44.1 setups. Our team of professional drivers help develop these setups at National events. Also, most drivers have a “base” setup that they use as a starting point for every event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track and mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then make adjustments based on the recommendations in this manual.
Battery Setup:
The B44.1 is designed to use LiPo saddle pack batteries. Follow your ESC and battery manufacturer’s recommendations for wiring.
Rear Ride Height:
The rear ride height setting you should use most often is 20 mm (the rear arms appear level when looking from the rear). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, raise or lower the shock collars as necessary until there is 20 mm gap from the bottom of the chassis to the ground. Note: Check the ride height gap at the rear end of the carbon fiber chassis, not at the rear chassis plate which is raised for more ground clearance. The chassis should look level from the side.
Steering Servo ChartAssociated
* Not all servo’s are listed* Make sure servo linkage clears the servo through full travel in both directions. Use #7336 servo spacers to adjust the servos position
XP-1015, XP-1313 F
F
F
F
A
A
H
H
J
J
J
# 9180servo arm
94102
HS-5625MG, HS-5645MG, HS625MG, HS645MG
Z4725, Z4750, Z2750, Z8450, Z8550, NES-4750
Z250, Z550
S9204, S9250, S9450, S148
S3003, S9202, S9101
S9404
94738, 94157, 94158, 94257, 94258, 94357, 94358, 94452, 94453, 94751, 94755
HS-322HD, HS-325HB, HS-965, HS-985MG, HS-5965, HS-5985MG, HS-425BB, HS-422
PS-401, PS-2001, PS-2004, PS-2015, PS-2173, PS-2174, PS-2123, PS-2143, PS-2144
Airtronics
Airtronics
Hitec
Hitec
JR
JR
Futaba
Futaba
Futaba
KO
25:: Shocks
:: Shock Springs
:: Differentials
:: Shock Oil
:: Lubes & Adhesives / Decals / Misc.
17771780418754076299641764436465646964726475692574747475747874797484964597239724
4412812141444622221612
1581
1582
649364946496649782326478648064816482743474357436
1
1
Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.
5420542154225423542454255426542754285429543054315432543354345435543654375438
1105159615976588659166366727
7167173816382038349777
2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.
1111112
111121
23303911391439766573657465796581658269099734
2112162
12121
FT Blue Aluminum Shock Pivot Ball/EyeletFT Blue Aluminum Shock Bushing, std.030 Nylon WasherRed O-Rings 1/8” E-ClipsFT Shock Shaft Gold 1.02”Bleeder Shock Caps 1/10 w/screwsShock Pistons, 4 each of #1,2, & 3Black Shock Cap O-RingShock Mount NutSpring Cup (used on rear)4-40 x 1/2“ SHCSV2 Threaded Shocks 0.89” CompleteV2 Threaded Shock Bodies 0.89”V2 Threaded Shocks 1.18” CompleteV2 Threaded Shock Bodies 1.18”V2 1/10th Shocks Rebuild Kit (rebuilds 4)2-56 x 1/8” bhcsFT Shock Shaft Gold 0.80”Offset Spring Cups (used on front)
Factory Team Buggy Front Spring Kit. I pair of green, silver, blue, black front springsFactory Team Truck Rear Spring Kit. I pair of green, silver, blue, gold, red rear springsFront Buggy Spring Brown 2.80 lb (Kit)Front Buggy Spring Green 3.50 lbFront Buggy Spring Silver 3.85 lbFront Buggy Spring Blue 4.20 lbFront Buggy Spring Black 3.20 lbRear Spring Silver 2.10 lbRear Spring Green 1.90 lb (Kit)Rear Spring Black 1.74 lbRear Spring Gray 2.33 lbRear Spring Blue 2.55 lbRear Spring Gold 2.75 lbRear Spring Red 2.95 lb
10 Weight Silicone Shock Oil20 Weight Silicone Shock Oil30 Weight Silicone Shock Oil40 Weight Silicone Shock Oil22.5 Weight Silicone Shock Oil80 Weight Silicone Shock Oil27.5 Weight Silicone Shock Oil15 Weight Silicone Shock Oil25 Weight Silicone Shock Oil35 Weight Silicone Shock Oil45 Weight Silicone Shock Oil55 Weight Silicone Shock Oil32.5 Weight Silicone Shock Oil37.5 Weight Silicone Shock Oil42.5 Weight Silicone Shock Oil50 Weight Silicone Shock Oil60 Weight Silicone Shock Oil70 Weight Silicone Shock Oil47.5 Weight Silicone Shock Oil
FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, mediumBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape
Reedy 2009 Sticker SetReedy Powered Logo DecalAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo StickerB44.1 Decal Sheet
Diff T-nutTrans. Shim SetDifferential Ring Gear & Drive Pinion Gear3/8 x 5/8” RS Ball BearingDiff Thrust Washer & Bolt5/64” Diff Thrust BallsDiff Drive Rings3/32” Carbide Diff BallsDiff Thrust SpringDiff Bearing 3/16 x 5/16”B44 Outdrives, Set
6469
6472
6443
9645
1780
6299
62997416
6925
7416
1777
3976
3911
3911
2330
6582
9734
6579
6579
9734
6573
6573
6573
3911
3911
3911
3911
6574
6909
6581
3914
6909
3976
1777
Front9724Rear6475
4187
6465
5407
Front7475Rear 7479
Front9723Rear 6417
54077484
7484
26:: Slipper / Spur Gears / Pinions
:: Pinions
:: Anti-Roll Bars :: Turnbuckles
165473817485748679359603964996509651965296539711973697409742
825282538254825582568257825882598260826182628263826482658266826782688269
412122111112111
111111111111111111
140414067230
Pr.Pr.12
6951882888309780
6111
FT Axle PinsCVD Rebuild KitFT V2 Slipper HubsFT V2 Slipper Spring and Washer.187 x .50 x .196” BearingSlipper Pad72T 48P Spur Gear75T 48P Spur Gear81T 48P Spur Gear (Kit)78T 48P Spur Gear84T 48P Spur GearB44 Bearing InsertB44 Slipper ShaftB44 Slipper NutB44 Slipper Drive Cups
15T 48P Pinion Gear16T 48P Pinion Gear17T 48P Pinion Gear18T 48P Pinion Gear19T 48P Pinion Gear20T 48P Pinion Gear21T 48P Pinion Gear22T 48P Pinion Gear23T 48P Pinion Gear24T 48P Pinion Gear 25T 48P Pinion Gear26T 48P Pinion Gear27T 48P Pinion Gear28T 48P Pinion Gear29T 48P Pinion Gear30T 48P Pinion Gear31T 48P Pinion Gear32T 48P Pinion Gear
FT Blue Titanium Turnbuckles 1.775” / 45mmFT Blue Titanium Turnbuckle 2.00 / 51mm”Ball Cups, Large
4-40 x 1/8” Set ScrewAnti Roll Bar Cups, SetAnto Roll Bar Pivots (with setscrews), SetB44 Anti Roll Bar Kit
9742
1654
9740
9741
7486
9736
9711
7935
7485
7485
9736
7935
9711
9736
1654
96039603
9651
9742
9742
7381
7381
8828
8828
8828
8830
6951
883097809780
7230
1404
1406
1406
7230
7230 7230
7230 7230
9780
6951
8828
27:: Front and Rear Gearboxes
:: Steering
:: Front and Rear Shock Towers
39033911391939774334629968607381799697339747976097619780
21128
1261212111
177938743981627262766277629269177336733779119180963097439744974689007
046
2866661411
101111
173617804449691774137738787497039704971997299772
645666811111
FT Servo Mount, blueBlock Carrier BushingsBallstud .20” Black, shortFoam Ballend Dust CoversBallstud .20” Silver, shortBallstud .30” Silver, short4-40 x 3/8” FHCS4-40 x 3/8” BHCSSteering Servo Mount Kit.250 x .125 x .015” WasherSteering Servo LinkServo Horns, MoldedBallstud WasherB44 Steering SetB44 Steering HardwareB44 Steering Bearing SetSteering Servo Ring, blue
FT Body Clips, Short, blueFT Blue Alum. Shock Bushing, std4-40 x 3/16” Alum. Locknut4-40 x 3/8” BHCS4-40 x 3/4” BHCS4-40 x 7/8” SHCS4-40 x 7/16” SHCSB44 Front Shock TowerB44 Rear Shock TowerB44 Body MountsB44 Wing MountsHigh Downforce Wing 6.5”
68606860
9733
9733
6299
6299
3903
3903
3919
39193911
3911
3911
3977
39777996
7996
9761
9761
7381
73817381
7381 9747
9760
9733
6292
6292
9743
97439746
9746
9746
9744
9743
97439743
9744
97443874
9743
6917
69179630
96306277
6277
9744
9744
97447911
9180
1779
17796292
6917
6917
6917
6917
73367337
7337
1736
17367874
9719
6917
6917
6917
6917
6917
97036917
74137413
74137413
97041780
1780
1780
9772
9729
9729
97299729
7738
4449
7336
6292
39816272
6272
6276
6272
6272
7911
7911
89007
9733
68606860
68606860
6860
6860
6860
6860
4334
43349780
9780
6860
6860
Drive PinionsTrans. Shim SetInput Shaft Hardware3/16 x 3/8” RS Ball Bearing2-56 x 5/16” BHCS1/8” Small E-ClipsFT 4-40 x 3/8” SHCS, blueCVD Rebuild KitPosilock QC Pin RetainerB44 Transmission CaseB44 Front CVA BoneB44 Center Bone, RearB44 CVA Input ShaftB44 Anti Roll Bar Kit
28:: Front and Rear Top Plates
:: Center Bulkhead and Motor Mount
1736433444496277628862926338691769256936970197029714971931113
62926924692597099712980098019802980331531
6661111116
FT Body Clips, Short, blue2-56 x 5/16” BHCS4-40 x 3/16” Alum. LocknutBallstud .30” Silver, short4-40 x 1/4” BHCS4-40 x 3/8” FHCSAntenna Tube 12”, black4-40 x 3/8” BHCS4-40 x 1/2” SHCSWashers, Alum. #4B44 Front Top DeckB44 Rear Top DeckB44 Shock Tower MountsB44 Body MountsAntenna Mount
4-40 x 3/8” FHCS4-40 x 3/8” SHCS4-40 x 1/2” SHCSB44 Center BulkheadB44 Center Bulkhead CapB44 FT Cam Motor Mount SetB44 FT Cam Motor MountB44 FT Motor Mount ClampB44 FT Motor Mount CamM3 x 6mm BHCS
FT Body Clips, Short, blue
4-40 x 3/16” Alum. LocknutBallstud .30” Silver, short
Antenna Tube 12”, black
B44 Shock Tower Mounts
17369719
6292
9714
4449
44496936
6936
6277
6924
6924 6924
69249712
9709
6292
6292
6292
6292 9801
9803
31531
31531
9802
9802
9802
9802
6925
9800
6925
6277
6288
6917
6917
4449
4449
9714
6925
6925
6925
6292
6292
6292
6292
9701
9702
6936
69366277
6277
6292
629231113
6338
43344334
685666166
1011111
29:: Front Suspension
:: Rear Suspension
22213977398344496272627769537369738179969645964797159716972097229747974897509751
6265
286641264
Pr.1
Pr.Pr.2222
397739836272693269527368736973817933793579969608963096459716975497649864987231286
26
2866
14412222
10612
Pr.Pr.1
4 ea.
3/16 x 3/8” RS Ball BearingBallstud .30” Black, shortFoam Ballend Dust Covers4-40 x 5/16” SHCS8-32 Locking Nut, Steel3/16” Axle Shims1/16” Universal Roll PinsCVD Rebuild KitCrush Tube GT2.187 x .50 x .196” BearingPosiLock QS Pin RetainerRR Axle Wheel SpacerBallstud Washer2-56 x 1/8” BHCSB44 Hinge Pin SetB44 Rear CVA BoneB44 Rear ArmB44 FT Aluminum Hub, 0˚B44 FT Aluminum Hub Tower SetAlum. Ballstud Washer (1mm, 2mm)
1222210612
Pr.Pr.1
4 ea.Alum. Ballstud Washer (1mm, 2mm)
9716
9716
9716
9716 9764
2221
2221 62726272
6272
7996
7996
3977
7935
7933
7368
9630
9864
3983
9872
6932
31286
7369
7369
7381
7381
7381
7381
9754
9748
9747
6277
4449
4449
6953
9750
9751
3977
3977
9647
9647
9720
9722
3983
6952
9608
9645
9645
9715
4-40 x 7/16” BHCS3/16 x 3/8” RS Ball BearingBallstud .30” Black, short4-40 x 3/16” Alum. LocknutFoam Ballend Dust CoversBallstud .30” Silver, short8-32 LP Steel Locknut1/16” Universal Roll PinsCVD Rebuild KitPosiLock QC Pin Retainer2-56 x 1/8” BHCSB44 Steering Block BushingB44 Front ArmsB44 Hinge Pin SetB44 Caster BlockB44 Steering BlockB44 Front CVA BoneB44 Front CVA AxleB44 Axle Drive HexB44 Front Crush Tube
30:: Chassis and Battery Mounts
17874449629264726915691769367673964597069713971497189719972697459765977497759786
256466
1064211
1 ea.2116112
FT Battery Strap Thumbscrews4-40 x 3/16” Alum. Locknut4-40 x 3/8” FHCSShock Mount Nuts4-40 x 5/8” FHCS4-40 x 3/8” BHCSWashers, Alum. #44-40 x 5/16” FHCS2-56 x 1/8” BHCSB44 Battery PostB44 Front BulkheadB44 Shock Tower MountsB44 Front & Rear BumperB44 Body MountsB44 Rear Chassis Plate, 3˚ arm mountB44 Servo Link and Setscrew4-40 x 7/16” FHCSB44.1 LiPo ChassisB44.1 LiPo Battery TrayB44 Battery Strap Carbon Fiber
1787
1787
9745
9745
9786
9786
9745
9745
9706
9706
9775
97756292
6292
6292
6292
9706
9706
6472
6472
9775
6292
6292
6292
9718
6917
6917
6292
6472
7673
9774
9719
9719
7673
7673
6292
4449
9714 9713
9645 9765
6292
1787
1787
97266292
7673
9718
4449
4449
9645
4449
4449
9726
6936
6936
6292
6292
6915
69159765
31:: Factory Team and Option Parts
1404140614111598165417281729173017311732173317361777177917801787641769036906693769437416747474757478747974847996
9608B9710972197239774977597769779978397849786978797959796979797989799980098019802980398649865986698679872
2221411
Pr.Pr.18612421
Pr.Pr.64
Pr.Pr.Pr.Pr.Pr.1221
Pr.111111121222221111
Pr.Pr.Pr.Pr.1
Ti Turnbuckle 1.775” BlueTi Turnbuckle 2.00” BlueTi Turnbuckle 0.75” BlueFT Blue Aluminum Shock CapFT Solid Axle PinsFT HD Front One-Way SetFT HD One-Way Housing SetFT HD One-Way Outdrive CupFT Bearings for HD One-WayFT HD One-Way Ring GearFT HD One-Way ShimsFT Short Body Clips BlueFT Blue Aluminum Ball/Eyelet SetFT Servo Mount Blue AluminumFT Aluminum Shock BushingBattery Strap ThumbscrewFT Shock Shaft Gold 1.02”3/8 x 5/8“ PTFE Bearings3/16 x 3/8” PTFE BearingsFT Blue 4-40 LocknutsFT Blue 8-32 LocknutsThreaded Shock CollarFT V2 .89” Threaded ShocksFT V2 .89” Threaded BodiesFT V2 1.18” Threaded ShocksFT V2 1.18” Threaded BodiesFT V2 1:10 Shock Rebuild KitCVA Pin RetainerRR Axle Wheel Spacer, blueB44 Alum. Center BulkheadB44 Alum. Caster BlocksFT Shock Shaft Gold 0.80”B44.1 LiPo ChassisB44.1 LiPo Battery TrayB44.1 LiPo Ballast WeightB44 Complete Bearing SetB44 Alum. Front Tower MountB44 Alum. Rear Tower MountB44 Carbon Battery StrapChassis Protective SheetTi Nitride Ballstuds 4-40 x 0.20” LongTi Nitride Ballstuds 4-40 x 0.30” LongTi Nitride Ballstuds 4-40 x 0.40” LongTi Nitride Ballstuds 4-40 x 0.20” ShortTi Nitride Ballstuds 4-40 x 0.30” ShortB44 Cam Motor Mount SetB44 Cam Motor MountB44 Motor Mount ClampB44 Motor Mount CamB44 FT Aluminum Hub, 0˚B44 FT Aluminum Hub, 0.5˚B44 FT Aluminum Hub, 1˚B44 FT Aluminum Hub, 1.5˚B44 FT Aluminum Hub Tower Set
:: Reedy Motors and ESC’s
:: XP Electronics
:: Reedy Batteries
:: Reedy Accessories
916917918919936937938939
2910729125291262913229140291412916629177292092921029211292122922129222
11111111
11111111111111
302303627632633634637686710712
605610654655656657658659660661662663664716
SP35MSP35L
SP35XLSP35XXL
SP35XXXLSP36MSP36L
SP36XLSP36XXL
SP36XXXLSP417SP418
1111111111
11111111111111111111111111
540R Brushless Motor 3300kV540R Brushless Motor 3900kV540R Brushless Motor 4900kV540R Brushless Motor 6100kVXP SC450-BL/Reedy 540R 3300kV ComboXP SC450-BL/Reedy 540R 3900kV ComboXP SC450-BL/Reedy 540R 4900kV ComboXP SC450-BL/Reedy 540R 6100kV Combo
S1903 Metal Gear SetS1903MG ServoS2008MG ServoSHV1504MG ServoXP SC200 Brushed ESC XP SC450-BL Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313 / DS1015Accessory Pack, DS1313 / DS1015XP3SS 2.4GHz Radio SystemTRS401SS 2.4GHz 4Ch Receiver
AA Alkaline 1.5V (4)AA 2700mAh NiMH 1.2V Rechargeable LiPo 60C 5200mAh 7.4V SPTX Lightweight Battery 1350mAh 11.1VTX Battery - 3PK, M11 3000mAh 11.1VTX Battery - Helios, Z1 2400mAh 11.1VTX Battery - M11X 2500mAh 7.4VLiPo 40C+ 4200mAh 7.4V SPLiPo 5100mAh 7.4V 35C SP ROAR SpecLiPo 4200mAh 7.4V 35C SP EFRA Spec
Motor Cooling Fans (2)AC/DC NiMH Peak Charger4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F)4.0mm plugs (100F)4.0mm plugs (10M)4.0mm plugs (30M)3.5mm plugs (3M, 3F)3.5mm plugs (10F)3.5mm plugs (100F)3.5mm plugs (10M)3.5mm plugs (30M)Reedy 09 Decal SetReedy Logo T-Shirt - White MReedy Logo T-Shirt - White LReedy Logo T-Shirt - White XLReedy Logo T-Shirt - White XXLReedy Logo T-Shirt - White XXXLReedy Logo T-Shirt - Black MReedy Logo T-Shirt - Black LReedy Logo T-Shirt - Black XLReedy Logo T-Shirt - Black XXLReedy Logo T-Shirt - Black XXXLFactory Team 1/10 Motor Storage BagFactory Team 1/10 Car Carrier Bag
:: LRP Brushless MotorsLRP50642LRP50652LRP50662LRP50672LRP50682LRP50687LRP50692LRP50702LRP50712LRP50722LRP50832LRP50842LRP50852LRP50862
11111111111111
LRP X-12 9.5 TurnLRP X-12 8.5 TurnLRP X-12 7.5 TurnLRP X-12 6.5 TurnLRP X-12 5.5 TurnLRP X-12 5.0 TurnLRP X-12 4.5 TurnLRP X-12 4.0 TurnLRP X-12 3.5 TurnLRP X-12 3.0 TurnVector X-12 Stock-Spec 10.5 TurnVector X-12 Stock Spec 13.5 TurnVector X-12 Stock Spec 17.5 TurnVector X-12 Stock Spec 21.5 Turn
32:: LRP Speed Controls
:: LRP Brushless Combos
:: LRP Charger, Power Supply, Balancer, Iron
LRP8320LRP8325LRP8337LRP80100LRP80150LRP80400LRP80800LRP80830LRP80900LRP80910LRP80950LRP86500LRP80905LRP80955LRP80460
LRP80640LRP80641LRP80642LRP80643LRP80644LRP80645LRP80646LRP80647LRP80648LRP80649LRP80654LRP80655LRP80656LRP80657LRP80658LRP80659LRP80673LRP80674LRP80675
LRP41281LRP41555LRP43150LRP45200LRP65800LRP65802LRP65803LRP65804
111111111111111
1111111111111111111
11111111
AI Super ReverseAI Pro ReverseAI Bullet ReverseAI Brushless ReverseAI Brushless Pro ReverseSPX Brushless Super ReverseV 8.1Quantum Competition 3SXX Competition Speed ControlSXX Stock-Spec Speed ControlSXX TC-Spec Speed ControlNEXXT 4X escSXX Competition V.2SXX TC-Spec V.2Ultimo Drift
SXX TC / X-12 3.0 TurnSXX TC / X-12 3.5 TurnSXX TC / X-12 4.0 TurnSXX TC / X-12 4.5 TurnSXX TC / X-12 5.0 TurnSXX TC / X-12 5.5 TurnSXX TC / X-12 6.5 TurnSXX TC / X-12 7.5 TurnSXX TC / X-12 8.5 TurnSXX TC / X-12 9.5 TurnSXX COMP / X-12 5.0 TurnSXX COMP / X-12 5.5 TurnSXX COMP / X-12 6.5 TurnSXX COMP / X-12 7.5 TurnSXX COMP / X-12 8.5 TurnSXX COMP / X-12 9.5 TurnSXX Stock-Spec / X-12 Stock-Spec 10.5 TurnSXX Stock-Spec / X-12 Stock-Spec 13.5 TurnSXX Stock-Spec / X-12 Stock-Spec 17.5 Turn
Quadra Pro 2 ChargerPulsar Touch Competition ChargerPower Supply CompetitionLiPo Parallel BalancerHigh Power Solder StationSoldering Tip 5mmSoldering Tip 1.2mmSoldering Handle
:: LRP Misc.LRP50620LRP50621LRP50622LRP50623LRP50624LRP50625LRP50626LRP50632LRP50633LRP50634LRP80135LRP82520LRP82511LRP819307LRP819310LRP819315LRP819320
11111111111111111
X-12 Replacement Ball BearingsX-12 Optional Ceramic Ball BearingsX-12 Small parts SetX-12 PreciSensor UnitX-12 Replacement alum Front canX-12 Lightweight Alum CanX-12 Alum Rear CoverX-12 12.0mm sintered rotorX-12 12.5mm sintered rotorX-12 13.0mm sintered rotorBEC stabilizing capacitorBrushless/Brushed Cooling SetBrushless Low Profile Fan70mm High Flex Sensor Wire100mm High Flex Sensor Wire150mm High Flex Sensor Wire200mm High Flex Sensor Wire
:: Apparel
:: 1/18 Kits and RTR’s
:: 1/12, 1/10 Kits and RTR’s
20100201012010320105201062011020115201182012020130
203320424019702070237027702970307032703470367037704070417043704470807092802080219034903690389039906120515301053010630111
** Use part number plus the desired size when ordering!
1111111111
11111111111111111111111111111
SP35**SP36**SP58**SP59**SP60**SP61**SP62**SP63**SP64**SP65**SP100SP101SP102SP103
SP410**SP415SP416SP417SP418
SP420**715
110684
1111111111111111111
Pr.11
RC18T RTR (ready-to-run)RC18T2 2.4ghz RTR (ready-to-run)RC18B2 - RC18T2 Team KitRC18B RTR (ready-to-run)RC18B2 2.4ghz RTR (ready-to-run)RC18MT RTR (ready-to-run)RC18R Kamino RTR (ready-to-run)RC18R Niteline RTR (ready-to-run)SC18 RTR (ready-to-run)RC18LM RTR (ready-to-run)
FT Nitro TC3 KitNitro TC3 RTR Plus (ready-to-run)FT 12R5.1 KitRC10T4 Team Truck KitRC10T4.1 FT KitSC10 2WD Short Course Race Truck KitSC10 Associated/RC10.com Truck RTR (ready-to-run)SC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 Ready Lift RTR (ready-to-run)SC10 FT KitRC10T4.1 RTR 2.4GHz Brushed (ready-to-run)RC10T4.1 RTR 2.4GHz Brushless (ready-to-run)SC10 RTR, 2.4ghz Brushless Lucas Oil BodySC10 RTR, 2.4ghz Brushless Speed Tech/Bully Dog BodySC10 RTR, 2.4ghz Brushless Pro Comp BodySC10 RTR, 2.4ghz Brushless Rockstar / Makita BodyFT GT2 Nitro Truck KitGT2 RS Truck Nitro RTR (ready-to-run)FT RC10R5 KitFT RC10R5-OVAL KitRC10B4 Buggy Team KitRC10B4.1 FT KitRC10B4.1 RTR 2.4GHz Brushed (ready-to-run)RC10B4.1 RTR 2.4GHz Brushless (ready-to-run)FT B44.1 4WD Buggy KitMGT 3.0 Nitro Monster Truck RTR (ready-to-run)FT TC5R Rubber Tire Edition 4WD Touring Car KitFT TC6 4WD Touring Car KitTC4 4WD Touring Car RTR (ready-to-run)
Reedy 09’ White T-Shirt (M, L, XL, XXL, XXXL)Reedy 09’ Black T-Shirt (M, L, XL, XXL, XXXL)AE Logo Black T-Shirt (M, L, XL, XXL)AE Logo Blue T-Shirt (M, L, XL, XXL)AE Hooded Sweatshirt (S, M, L, XL, XXL)AE Vertigo Hooded Sweatshirt (S, M, L, XL, XXL)AE Vertigo Long Sleeve T-Shirt (S, M, L, XL, XXL)AE Vertigo White T-Shirt (S, M, L, XL, XXL)AE Vertigo Blue T-Shirt (S, M, L, XL, XXL)AE Vertigo Black T-Shirt (S, M, L, XL, XXL)1/8 Inner and Outer Boxes Only, Set1/8 Inner Boxes Only, Set1/10 Inner and Outer Boxes Only, Set1/10 Inner Boxes Only, SetAE Hats Black (S-M, L-XL, XXL-XXXL)1/8 Car Carrier Bag Only1/10 Car Carrier Bag Only1/10 FT Motor Bag1/10 FT Car Carrier Bag with Boxes, SetAE Pit Gloves (M, L, XL)Reedy 2009 Track BannerTeam Associated Track Banner
33:: 1/8 Kits and RTR’s20503
20504
809028090480905809128091580920
80921
80922
80923
80924
80925
80932
1
1
111111
1
1
1
1
1
1
Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)FT RC8B Nitro Buggy KitFT RC8Be Electric Buggy KitRC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)RC8T Championship EditionRC8T-RS “Race Spec” Nitro Truggy RTR (ready-to-run)SC8 Short Course Race Truck, Red Bull Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Lucas Oil Nitro RTR (ready-to-run)SC8 Short Course Race Truck, KMC Wheels Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Bully Dog Nitro RTR (ready-to-run)SC8 Short Course Race Truck, AE Team Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Pro Comp Nitro RTR (ready-to-run)SC8e Short Course Race Truck Rockstar/Makita RTR (ready-to-run)
:: Contact Information
:: Tools111114491450154115421543154415451546154715481551155315541561156215631564156515661567158915901592171917373718371937203987642969567709
1111111111111111111111111112121211112
Associated Electrics, Inc.26021 Commercentre Drive
Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com
http://www.RC10.comhttp://twitter/Team Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500fax: (949) 544-7501
Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
FT Turnbuckle WrenchOffroad Ride Height GaugeFT Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Screwdriver SetFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 7.0mm Silver Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesFT Droop GaugeShock Building ToolMolded Tools, Set4 Inch Nylon Wire Ties
34:: Notes
Driver: Date: Track: Event:Conditions: Rev.1Setup Sheet
:: For more setups, visit RC10.com and click on “Setup Sheets”
Front Suspension
Front Shocks
Electronics
Differentials
Front Tires
Race and Vehicle Comments
Other
Rear Tires
Track Info
Rear Suspension
Rear Shocks
Anti Roll Bar:
0.047” Black0.055” SilverNone
Anti Roll Bar:
0.047” Black0.055” SilverNone
Spring: Piston:Shock Oil: Limiter:
Motor & Wind:Pinion:Spur Gear:Batteries:Battery Placement:
Front Diff Setting:Rear Diff Setting:
Tire:Compound:Insert:Wheel:
Qualify: Main: Finish: TQ:Comments:
Tire:Compound:Insert:Wheel:
Smooth: Bumpy: Blue Groove:Traction: High: Medium: Low:Soft Dirt: Grass: Clay: Wet:Dusty: Other:
Radio:Throttle / Brake e.p.a:Throttle / Brake expo:ESC: Throttle Profile:Initial Brake: Drag Brake:Servo: Steering Expo:
Body Type:Wing Type: Wing Angle:
Spring: Piston:Shock Oil: Limiter:
Bumpsteer Washer:
Camber:
Toe:
Ride Height:
Camber:
Toe:
Ride Height:
Notes:
Washers:
Notes:
Wheelbase:LongMediumShort
Aluminum Hub Tower:AB
1
12
12
1
22
I O
Steering Rack:
FrontBack
I O
A B
A CB D
B44.1 Standard Setup
0
-1˚
0˚
21mm
1
-1˚
3˚
20mm
Measure ride
Silver Green35 wt
Standard JConcepts Punisher6.5” high 9˚Standard
Holeshot 2.0 Holeshot 2.0M3 M3
Standard StandardStandard Standard
30 wt1 1#2 #1
height on back cornerof chassis
36
4-40x5/16” (7673)
4-40x3/8” (6292)
4-40x7/16” (9765)
4-40x5/8” (6915)
2-56x1/8” (9645)
2-56x5/16” (4334)
4-40x1/4” (6228)
4-40x3/8” (6917)
4-40x7/16” (2221)
4-40x3/4” (7413)
4-40 Aluminum Locknut (4449)
4-40 Plastic Nut (6472)
5-40 Nylon Locknut (9744)
8-32 LP Steel Locknut (6953)
8-32 Steel Locknut (6952)
E-clip (6299)
5/64” Diff Thrust Balls (6574)
3/32” Carbide Diff Balls (6581)
Ballstud Washer (9630)
.030” Nylon Spacer (4187)
Servo Mount Washer (7337)
#4 Washer (6936)
Input Shaft Shim - Black (3911)
3/16” Axle Shim - Silver (7368)
Outdrive Shim (3911)
:: Hardware - 1:1 Scale View
Cap Head (shcs)
Top Hat Bushings
Ball Bearings
Notes:
Flat Head (fhcs)
Shims and Washers
Button Head (bhcs)
Nuts (lock/plain)
Clips
Diff Balls
4-40x5/16” (6932)(aluminum ,4145)
4-40x3/8” (6924)(aluminum ,6860)
4-40x7/16” (7874)(aluminum, 7873)
4-40x1/2” (6925)
4-40x7/8” (7738)
3x6mm (6515)(motor mounting screws)
Small Top Hat Bushing (3874)
Large Top Hat Bushing (9647)
Steering Bearing (9746)
3/16x5/16” (6906)
3/16x3/8” (3977)
3/16x1/2” RS (7935)
3/8x5/8” RS (3976)Ballstuds
Silver .20” Short (6276)
Silver .30” Long (6277)
Black .30” Long (3983)
Wheel B
ase Sh
ims
1mm
2m
m
Cam
Hold
er
AB
1º1.5
º2º
Arm
Mount Sh
ims
21
Wheelb
ase
Wheelb
ase
Hex S
pacin
g
Toe
0+ -To
e0+ -
Hex S
pacin
g
Cam
ber
0
+
-
Bum
psteer
Outer B
all
& S
him
s
Outer B
all
& S
him
s
Driver: Date: Track: Event:Conditions: Rev.1Setup Sheet
:: For more setups, visit RC10.com and click on “Setup Sheets”
Front Suspension
Front Shocks
Electronics
Differentials
Front Tires
Race and Vehicle Comments
Other
Rear Tires
Track Info
Rear Suspension
Rear Shocks
Anti Roll Bar:
0.047” Black0.055” SilverNone
Anti Roll Bar:
0.047” Black0.055” SilverNone
Spring: Piston:Shock Oil: Limiter:
Motor & Wind:Pinion:Spur Gear:Batteries:Battery Placement:
Front Diff Setting:Rear Diff Setting:
Tire:Compound:Insert:Wheel:
Qualify: Main: Finish: TQ:Comments:
Tire:Compound:Insert:Wheel:
Smooth: Bumpy: Blue Groove:Traction: High: Medium: Low:Soft Dirt: Grass: Clay: Wet:Dusty: Other:
Radio:Throttle / Brake e.p.a:Throttle / Brake expo:ESC: Throttle Profile:Initial Brake: Drag Brake:Servo: Steering Expo:
Body Type:Wing Type: Wing Angle:
Spring: Piston:Shock Oil: Limiter:
Bumpsteer Washer:
Camber:
Toe:
Ride Height:
Camber:
Toe:
Ride Height:
Notes:
Washers:
Notes:
Wheelbase:LongMediumShort
Aluminum Hub Tower:AB
1
12
12
1
22
I O
Steering Rack:
FrontBack
I O
A B
A CB D
Associated Electrics, Inc.26021 Com
mercentre Dr.
Lake Forest, CA 92630 USAhttp://w
ww
.TeamAssociated.com
http://ww
w.RC10.com
http://twitter/Team
_Associatedhttp://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501Check out the follow
ing web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
ww
w.Team
Associated.com. - w
ww
.RC10.com
top related