asphalt binders

ENCI 579 1

Asphalt Binders

ENCI 579 2

Introduction

• Terminology / Uses• Sources / Manufacturing • Composition / Product Types• Temperature Susceptibility• Specifications / Testing• Modifiers / Additives

ENCI 579 3

Terminology• Asphalt/Bitumen

– A mixture of heavy carbon-based compounds containing a high percentage of multiple-ring aromatics, many involving sulfur, nitrogen and oxygen atoms

– hydrocarbons soluble in CS2

– Brown-Black semi-solid material which is solid at room temp but softens and flows when heated

– Asphalt Cement - binder - oil• Asphalt Concrete - Pavement

– Asphalt Cement plus Aggregate

ENCI 579 4

Asphalt Uses• Paving Material• Preservative / Protection• Waterproofing / Roofing• Insulator / Adhesive / Lubricant• Industrial & Building Material• Fuel oil - Bunker, LIFO, MIFO• Conversion Feedstock

– produce lighter petroleum products - gasoline, diesel etc

ENCI 579 5

Asphalt Uses

ENCI 579 6

Asphalt Uses

ENCI 579 7

Asphalt Uses

ENCI 579 8

Asphalt Uses

ENCI 579 9

Asphalt Uses

ENCI 579 10

Asphalt Uses

ENCI 579 11

Asphalt Sources• Native or Natural Asphalts

– bitumens with inorganic impurities• Trinidad lake has 25-50% insolubles

– Asphaltites - no impurities, high asphaltene content• Gilsonite - Eastern Utah

– Rock Asphalts -- asphalt in rock• impregnated sandstones - Oklahoma• tar sands - Alberta• oil shales - Colorado

ENCI 579 12

Asphalt Sources

• Tars - distillation of coal– Pitch is distillation residue of tar

• Petroleum asphalts from crude oil

ENCI 579 13

Manufacturing

• Asphalts produced from crude oil• Crude Oil Taxonomy - 18 Classes

– Light, Intermediate, heavy– Sweet, Intermediate, Sour– Paraffinic, Napthenic

• Best crudes for paving asphalts are heavy napthenic crudes

ENCI 579 14

Crude Oil• Crude oil is found as a natural deposit on the

earth’s surface or buried up to 18,000 ft deep• First oil wells were drilled in China in 347 AD

using bits attached to bamboo poles and achieved depths up to 800 ft

• Modern oil era was originally driven by kerosene oil for lamps

• Edison’s light bulb reduced demand but was offset by internal combustion engine gasoline

ENCI 579 15

Petroleum Deposit of Western Canada

• Western Canada has the complete spectrum of hydrocarbons from light sweet crude to tar sands

• Generally oil is heavier towards the northeast. That is the closer to the Rockies, the lighter the crude.

• Lloydminister heavy oil can be produced by conventional means while Cold Lake can only be recovered by thermal stimulation

• The tar sands must be physically mined

ENCI 579 16

Refining Crude• Most impact on the asphalt properties is from the crude

source but the manufacturing process can also have an effect

• There are 80 refineries in North America producing asphalt - 5 in Western Canada

• Typically integrated refineries produce asphalt as a by-product, but there are dedicated asphalt refineries as well.

• Primary asphalt manufacturing is by fractional distillation

ENCI 579 17

Refining Crude

ENCI 579 18

Cracked Asphalts

• Very poor paving materials• breaking down large hydrocarbons into smaller molecules

through the application of temperature pressure and use of catalysts

• Thermal crackers• Cokers• Catalytic Cracking• Hydrocracking

ENCI 579 19

Constitution of AsphaltAsphalt - colloid multiphase mixture of millions of different

components

Identification by groups of components

Asphalt

heptane

asphaltenesTCE

polar aromatics

toluene

methanol + toluene

saturates naphthene aromatics

ENCI 579 20

Asphaltenes

• General belief that unaltered asphaltenes have a definite composition• Notable variation in the proportion of heteroatoms:

– Oxygen: 0.3 -4.9%– Sulphur : 0.3 - 10.3%– Nitrogen : 0.6 - 3.3%

• Dark brown or black solids insoluble in nonpolar solvents

• Elemental composition varies only over narrow rangeCarbon : 82 3%Hydrogen : 8.1 0.7%

ENCI 579 21

Asphaltenes

ENCI 579 22

Resins• Dark semisolid or solid, very adhesive fractions• Soluble in liquids that precipitate asphaltenes

C/H ratio : 7.5 ~ 9.1Hydrogen : 9.5 ~ 11%

• Polycyclic structures with 5~6 rings (2~3 aromatic on which there are aliphatic substituents

ENCI 579 23

Oils

• Lowest molecular weight hydrocarbons in asphalt • Similar to lubricating oils - highest boiling

fraction of lubricants• Control the harness of asphalt• Single or condensed naphthene and aromatic rings

with side chains of varying length

ENCI 579 24

Oils

mono-, di-, polynuclear aromaticsC/H ratio : 6.8 ~ 8molecular weight : 240 ~ 800, most 360 ~ 500

ENCI 579 25

Structure and Colloidal Properties of Asphalts

• Physical properties of asphalt = f (dispersion of asphatenes in maltenes)

• Peptizing effect of aromatic and resin portions of maltenes keep the colloidal structure of asphalt

• Prime consideration - rate of absorption of higher MW maltenes on the asphaltene particles = f(time, temperature)

ENCI 579 26

Structure and Colloidal Properties of Asphalts

ENCI 579 27

ENCI 579 28

ENCI 579 29

ENCI 579 30

ENCI 579 31

Asphalt Products

• Asphalt Cements– reduce viscosity by heating

• Cutback Asphalts– reduce viscosity by blending with a solvent– RC, MC, SC

• Asphalt Emulsions– Asphalt in water - or inverted– Anionic or Cationic - charge of particles– RS, MS, SS

ENCI 579 32

ENCI 579 33

Asphalt Testing

• Penetration• Viscosity (shear rate)• Softening Point (R & B)• Ductility• Flashpoint (COC, PM)• Solubility (TCE)• TFOT, RTFOT• Mass Loss, Aging Index

ENCI 579 34

Specifications

• Classical Specifications were designed to describe the material not its performance

• Recent specifications (CGSB ) have incorporated some performance criteria

• Superpave specifications are used to define performance using new methods of measuring properties

ENCI 579 35

ENCI 579 36

ENCI 579 37

ENCI 579 38

ENCI 579 39

ENCI 579 40

ENCI 579 41

ENCI 579 42

ENCI 579 43

ENCI 579 44

ENCI 579 45