air jet manual
Post on 29-Nov-2015
183 Views
Preview:
TRANSCRIPT
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 1
USER MANUAL OF AIR JET EROSION TEST RIG
AS PER ASTM G76
By,
M/s. Magnum Engineers
Peenya, Bangalore-58.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 2
CONTENTS
1. INTRODUCTION
2. TYPES OF EROSION RIGS
3. DESCRIPTION OF THE EQUIPMENT
4. MAJOR PARTS OF AIR JET EROSION TEST RIG
5. TEST PROCEDURE
6. MAINTENANCE & SAFETY
7. PHOTOGRAPHS OF AIRJET EROSION TEST RIG
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 3
PART I
GENERAL INFORMATION
WARRANTY
The equipment is warranty for a period of 12 months from the date of instillation.
When the consignment reaches your place, please check the items as per the list provided along
with the machine. If there any short or any damage found please send E-mail or inform us over
the below telephone number immediately.
1. 080-41170935 2. E-mail: magnumengg@yahoo.com
SAFETY PRECAUTIONS
� The AIR JET EROSION TEST RIG AS PER ASTM G76 is an electro-mechanical Device. Please follow
the instructions carefully.
� Personnel injury may be resulted by improper operation.
� The equipment may be damage by improper operation.
� Only our service engineer installs and services the equipment.
� Please ensure proper earthing.
� Voltage between Earth and Neutral should be less than 5 Volts.
� Do not attempt at wire circuitry while power is ON.
� Do not attempt to examine the components and signals when the equipment is ON.
� Do not attempt to disassemble or modify internal circuitry or wiring.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 4
INTRODUCTION
The solid particle erosion is a form of material degradation caused by the impact of hard particles
against a target material, at reasonably high velocities (>10 m/s). Mechanically solid particle erosion is
quite different from the other form of erosion like liquid impact erosion and cavitations erosion, since
the contact between the contact between the hard particle and the material is only momentary during
erosion. It is different from other related wear processes like sliding wear, abrasion, grinding and
machining.
Solid particle erosion (henceforth referred to as erosion) is immense technological and economic
importance as illustrated in the following examples:
The performance of aircraft and helicopters operating in dusty environment
Industrial gas turbines burning coal as fuel deteriorate both structurally and aerodynamically in the
presence of solid particles in the fluid.
Bulk particulate matters are transported from one location to another by pneumatically conveying them
through pipelines. Erosion of these pipes at the bends and changes in direction is a severe problem
especially when the conveying product is abrasive and angular. Definite interrelationship has been
established between the maximum depth of penetration and the mass erodes, phase density, and mean
particle size and the bends geometry.
Erosion is a severe problem in coal gasification and liquefaction plants. Plant failure analysis indicates
that two third of the reported failures are material related. Of this one third were due to erosion.
Gun barrel undergoes erosion during firing of a round from the barrel, hot gases move down the barrel,
behind the accelerating projectile at velocities greater than 500 m/s, sufficiently high to scour the metal
ROM the surface. The entrainment of solid particle of combustion unburned propellant and wears
debris formed by sliding wear causes erosion of the barrel material.
A wide range of equipment’s used in the oil industry and the thermal power plants suffer significant
erosion.
To develop the erosion resistant materials and coatings for various applications one needs specialized
test facilities. In the area of erosion testing the situation is particularly bad since only very recently
ASTM (American Society for Testing and Materials) published a standard for solid particle erosion
testing procedure. In addition erosion rigs are not being manufactured anywhere in the world on a
commercial basis. Therefore, the erosion rigs have to be fabricated locally.
The design of erosion rig requires the consideration of a few important aspects; firstly, the actual
operating conditions relevant to the system of interest should be characterized. Typically, the following
information should be available.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 5
The velocity and the angle of impact of particles on the component surface.
System temperature and pressure
Impacting particle size, shape, density, hardness
The nature and inertness of the fluid carrying particles
The concentration of the particles in the fluid i.e. phases density.
In most of the cases the data on impact velocity and the attack angles is hard to come by due to the
inaccessibility of the component of interest. In such a situation, the computer modeling of the
component and the simulation of the two-phase particle – fluid flow behavior will be necessary to arrive
at the reasonable values of velocity and angle. It may be noted that even though the most of the test
parameters listed above are easily obtainable, the test rig should be built over a range around these
known values of test parameters. Secondly, the effect of various parameters like temperature, impact
velocity, and angles, particle related properties on the erosion behavior must be known early on, either
through comprehensive literature survey or on the basis of past experience. This is necessary because
the erosion rig should simulate closely at least those parameters, which markedly influence the erosion
rate. For example it’s well known that the rate of erosion is independent of the impacting particle
hardness as long as it’s about twice the hardness of the target material. Therefore if the hardness of the
eroding particle is more than twice that of the target material, a more suitable erodent has to be use
TYPES OF EROSION RIGS
Erosion is simulated in the laboratory by one of the methods. The “sand blast method “, where particles
are carried in a stream of air and impacted into a stationary target and the”whirling arm method”,
where target is spun through a chamber of particles. On the basis of high accuracy achievable and the
design simplicity the present machine is based on sandblast type. A continues flow of dry air through a
mixing chamber accelerates the erodent particles up to a high fraction of the air velocity. The particles
then exit the nozzle in an erosive jet, where they impact a stationary target enclosed in a separate
chamber. The distance of the nozzle and the target can be adjusted using a power screw mechanism to
elevate or lower the entire specimen block. The erosion rate is calculated based on the weight loss
method and wear mechanism can be studied using SEM.
The erosion rigs are also classified based on velocity and temperature capabilities as:
(i)High velocity (>10 m/s), room temperature (HVRT) erosion rig.
(ii)High Velocity, high temperature (up to 400 C) (HVHT) erosion rig.
(iii) Low velocity (<10 m/s), room temperature (LVRT) erosion rig.
(iv) Low velocity, high temperature (LVHT) erosion rig
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 6
DESCRIPTION OF THE EQUIPMENT
The “Air Jet Erosion Testing Equipment “ designed and fabricated by M/s. Magnum Engineers,
Bangalore is the first compact and light - weight erosion testing equipment ever built in India for solid
particle erosion testing. The equipment is one of its kinds in terms of testing utilities, the user- friendly
features it offers on the one-piece control panel and appeals with its pleasing esthetics. Built according
to the ASTM (American Society for Testing and Materials) G-76 standards for erosion testing, the
equipment can be used for testing polymers, coatings, steels, organic materials for wear loss due to
erosion over a range of impinging velocities, particle sizes, particle flux and attack angles.
Erosion, which is a process of wear, may be broadly defined as the progressive loss of material from a
solid surface due to mechanical interaction between the surface and a fluid, a multi-component fluid or
impinging solid or liquid particles. Specifically in the present machine the mechanical interaction is
nothing but a momentary contact of the erosive particle with the specimen, which leads to scouring of
the material and consequent loss of the original material.
Erosion is an important wear mechanism in industrial applications. Despite the existence of ASTM and
DIN standard methods, everyone has their own way of doing erosion tests. ASTM G 76 "Standard
Practice for Conducting Erosion Tests by Solid Particle Impingement" in fact acknowledges that the one
single laboratory test may not be sufficient to evaluate expected service performance. Actual erosion
service can involve a range of particle sizes, velocities, attack angles & environments, all of which
influence erosion rate.
Key parameters to define and control in an erosion test are as follows:
1. Particle velocity. This is not the same as the air velocity, but is often assumed to be 3.3times the air
velocity.
2. Particle mass flow rate
3. Nozzle wear
4. Particle spread from nozzle
5. Size and shape of particle
6. Angle of impact of the particles
7. Properties of the material are being tested.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 7
One particular feature of the ASTM G76 method is the fact that the very small jet diameter (1.5-
mm) results in the particles "drilling" into the surface. The standard states that the depth of
penetration should not exceed 1 mm. This is a deep hole in any surface and in fact the deeper the
penetration, the more the physical state of the erosion jet will change (due to interaction of the
particles hitting the surface and rebounding).
These very severe test conditions are not appropriate for coatings, for which the test must be designed
to determine the wear of the coating, not the substrate material. The present machine serves at milder
testing conditions in terms of attainable particle velocities and mass flow rates of the erodent.
A related problem of a small nozzle size such as that defined by ASTM is that the nozzle will wear. This
result in a change in the shape of the particle stream as it emerges from the nozzle and this will result in
variability in the data.
ASTM G 76 defines a nozzle of 1.5-mm inner diameter and 50 mm long. This small nozzle size means
that there is a large backpressure and the abrasive sand has to be fed under pressure to achieve the
required mass flow rates (2 +/- 0.5 g/minute). A pressure of 20 p.s.i. (1.4 bar) at the entry to the nozzle
is typically required to give a particle velocity of 30 m/s.
The nozzle does not have to be manufactured from Tungsten Carbide; instead they are made from
standard seamless drawn type 304 stainless steel tubing. The internal surface finish can be carefully
controlled and the cost of replacement nozzles when necessary is very low.
The larger nozzle diameter results in a wider spread of particles which are therefore more suited to
erosion testing on coatings as well as solid material: there is less of a tendency to "drill" holes in the
surface; In addition, there is a much smaller influence of rebounding particles on the impinging jet,
resulting in a better controlled erosion process.
The larger nozzle size also permits a wider range of particle types to be used in the course of testing,
allowing better simulations of real erosion conditions.
The mass flow rate is controlled by use of a rotating grooved disc and particles are delivered from the
groove to the air stream by way of venturi suction. Mass flow rate is adjusted by controlling the speed
of the rotating disc. Particles are fed from a simple hopper under gravity into the groove.
The air pressure and length of nozzle determine the velocity of the particles. A wide range of particle
velocities is covered 27m/s (corresponding to 81m/s of air velocity) and a feed rate of 0.2 to 200
g/minute.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 8
Features:
1. Vertical traverse for the sample stage: provides variable height, which influences the size of the
eroded area.
2. Different nozzles may be accommodated: provides ability to change the particle plume dimensions
and the velocity range
3. Large test chamber with sample mount (typical sample size 75 mm x 25 mm) that can be angled to
the flow direction: by tilting the sample stage, the angle of impact of the particles can be changed and
this will influence the erosion process.
4. Optional heating system: permits “hot” tests up to 250°C
5. An erodent reservoir capable of storing an additional 3 kg of erodent.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 9
MAJOR PARTS OF THE AIR JET EROSION TEST RIG.
1. Abrasive storage Hopper (TOP).
2. Abrasive Flow Control Knob.
3. Abrasive Nozzle-Height Adjustment.
4. Vibrator Pad-Pneumatic Type.
5. Pressurized conveyor abrasive flow chamber
6. Specimen holding-heater block, heater, specimen sample, and indexing unit.
7. Double disc assembly-motor, upper disc with slit, lower disc without slit, arrangement to hold.
8. Dust collecting unit (gunny bag).
9. Display panels.
10. Air dryer.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 10
DISPLAY PANELS:
1. Digital Pressure indicator
2. Digital Preset timer indicator
3. Digital Preset temperature controller
4. Heater on-off switch
5. Pulse meter for rpm indication
6. Panasonic Conveyor speed controller
7. Double disc speed controller
8. Mains ON-OFF switch
9. Vibrator knob (For abrasive hopper)
10. Pressure regulator valve
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 11
Description of Control Panels:
Pressure indicator: which indicates the operating pressure of the system?
Ex: 1.5bar
This can be varied by pressure control knob
During test condition once the pressure is set, don’t vary.
Preset time indicator: It is an instrument, which indicates set time for the test.
Ex: Hr-Min-Sec
Temperature indicator and controller: It indicates set temperature for the test.
It can also set for the required temperature value
Heater switch: It is provided for heater to ON-OFF.
Pulse meter-Indicator: this indicates the speed of the double disc motor.
Conveyor motor speed controller: It is used to set the conveyor motor for the required speed. It
ranges from 4 rpm to 28rpm.
Double disc speed knob: This knob is used to vary or to set the required speed of the double disc
motor.
Here we can increase or decrease the speed of the double disc and also we can set for the required
speed during calibration process.
Maximum speed of the motor is 3000rpm.
Main ON-OFF switch: this switch is used to ON/OFF the machine.
Double disc ON-OFF switch: this is a separate on-off switch given for Double disc system, which
should be used during calibration process
Vibrator knob: this knob controls the flow of air to the vibrator, which is fixed on the sand hopper.
This vibrator is of pneumatic type, by increasing or decreasing the flow rate air to the vibrator we can
control the vibrating action of the sand hopper.
By providing this type of vibrator, sand from hopper will flow freely without any disturbance.
Pressure regulator: pressure regulators are used to regulate the flow of dry air into the system.
Required pressure can be achieved by varying the pressure-regulating knob.
Before opening the pressure-regulating knob ensure for following.
1. Compressor is switched ON.
2. Compressor OUTPUT connected to dryer INPUT.
3. Dryer OUTPUT connected to test rig INPUT
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 12
Safety Precautions:
1. Do not open the door during test condition
2. High velocity dry air along with abrasive from nozzle is harmful to body.
3. Do not inhale the abrasive dust, it is dangerous to health.
4. As soon as the test time completed, switch off the heater switch.
5. Remove the specimen; allow it to cool for sometime.
6. Use recommended abrasive size.
7. Do not use the sand that as already used for the test.
8. Double disc arrangement must be kept in safe place.
9. Use safety gloves to remove heated sample after the test completes.
10. Use safety goggles while testing is going on.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 13
Test procedure:
1. Check that all the switches, knobs and valves are in OFF position.
2. Clean the test rig before the test starts.
3. Connect the test rig to 230V 50 Hz supply.
4. Start the compressor. (Ensure pressure regulator valve is closed)
5. Connect outlet of compressor to input of dryer, output of dryer to air inlet provided on
backside of the test rig.
6. Switch on the dryer.
7. Switch ON the mains.
8. Place the specimen on the specimen holding block and clamp firmly using the clamping
fingers provided. (Before placing clean the specimen and weigh the specimen on the
electronic balance to know the initial weight of the specimen).
9. Maintain 10mm distance between specimen surfaces to nozzle tip (ASTM STANDARD) and
tilt the specimen holding block for the required angle.
10. Fill the abrasive storage hopper with abrasive.
11. Adjust the sand nozzle for the required height by adjusting the nut (knurled round nut).(gap
between abrasive flow nozzle and abrasive feed conveyor
1. Set the conveyor motor for the required speed.
2. calibrate for the abrasive flow rate (gm/min)
3. Switch ON the heater and set the heater for the required temperature.(if the test based on
temperature)
4. Set the preset timer for the required test period in HH-MIN-SEC.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 14
5. Release air to sand vibrator, which starts to vibrate.
6. Close all the doors.
7. Open the pressure-regulating valve for the required operating pressure.
8. Press the cycle start button.
9. Once the test time is completed, air is closed, switch OFF the heater, open the door, and
allow the specimen to cool for sometime.
10. Remove the specimen, clean it and reweigh the specimen on electronic balance.(0.1mg)
11. Difference in weight loss can be observed.
12. Once the specimen is removed, close all the valves, knobs and switches.
13. Clean the test rig for every test.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 15
PROCEDURE FOR DOUBLE DISC METHOD
TO FIND PARTICLE VELOCITY
� Place the double disc arrangement unit in its position and clamp it firmly by tightening the
thumbscrew provided.
� Remove the upper disc.
� Set the speed of the lower disc to 1500 to 3000 rpm.
� Apply the lapping paste on the surface of rotating lower disc; apply light pressure on the
disc with scratch pad in order to remove the impressions of last test.
� Observe for removal of sand impressions.
� Clean the disc with good cloth or tissue paper.
� Stop the rotating disc, once again clean well for no mark or impressions.
� Place the upper disc on the lower disc, which has got slits on four sides on its circumference.
� Mark the reference line on the lower disc with respect to the upper disc slots.
� Tighten the disc firmly provided Allen screw.
� Switch on the double disc and set the known RPM.
� Set the pressure regulator for the required pressure.
� Set the test period through pre set timer.
� Set the conveyor speed for sand displacement.
� If the abrasive not flowing properly, open the pneumatic vibrator for easy flow of sand.
� Close all the doors.
� Press the cycle start button.
� When the test duration completes, turn the pressure regulator, pneumatic vibrator, double
disc speed and conveyor speed knob to zero position.
� Remove the double disc arrangement from its position; clean the arrangement with good
cloth or through acetone.
� Remove the upper disc and observe the impressions made by sand particles on lower disc
during the test period.
� Calculate the particle velocity in m/sec as per the procedure given below.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 16
Procedure for calculating the particle velocity:
We know that S= R* Ø
Where,
S= sector length in mm
R= radius of the lower disc in mm S
Ø = angle in radians Ø
R
Particle velocity (Vp) is given by the formulae 2×22÷7×N×R×L m/sec
60×S
Where,
Vp particle velocity in m/sec
N speed of the double disc rev/min
R radius of the lower disc in mm
L distance traveled by sand particles, or distance between upper disc and lower disc in
mm
S sector length in mm
Sand impressions
Lower disc
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 17
Ensure:
1. Proper size abrasive in the abrasive hopper.
2. Ensure that proper size specimen is placed and fixed rigidly.
3. Ensure for compressor is ON and pressure regulator is in OFF condition while starting the
compressor.
4. Ensure that the specimen is cleaned and weighed on electronic balance before placing the
specimen on specimen holding block.
5. Ensure for proper hold of the double disc assembly by tightening the knob provided on the
holding unit during calibration process.
6. Ensure for the diameter of the nozzle.
7. Ensure for test temperature before cycle starts.
8. Ensure for all doors are closed before test starts.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 18
Maintenance and Safety:
1. Clean the machine for every test.
2. Use moisture free dry abrasive, so that abrasive will flow freely from abrasive flow nozzle.
(Heat the abrasive in oven for 10min at 120 degree centigrade.)
3. Keep safely the double disc arrangement when it is not in use because if the slit on the
upper disc is damaged, there will be an error in calibrated readings.
4. Polish the lower disc for every test, such a way that the centerline on the disc must be
visible.
5. The distance between upper disc and lower disc must be 25mm.
6. Adopt safety procedures while conducting test.
7. While test is going on don’t open the front doors.
8. After the test completes, allow the specimen for 5 minutes for cooling if the test is
temperature based.
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 19
PHOTOGRAPHS OF AIR JET EROSION TEST RIG
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 20
AIR JET EROSION TEST RIG AS PER ASTM STANDARD G76
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 21
TOP FRONT PANEL OF
AIR JET EROSION TEST RIG
BOTTOM FRONT PANEL OF
AIR JET EROSION TEST RIG
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 22
TEST PRESSURE INDICATOR
TEST PERIOD INDICATOR
TEST SET TEMPERATURE INDICATOR
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 23
SPECIMEN HEATING ON/OFF
DOUBLE DISK SPEED INDICATOR
ABRASIVE CONEVYOR SPEED CONTROLLER
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 24
DOUBLE DISC SPEED VARIABLE KNOB
DOUBLE DISC ON /OFF KNOB
CONTROLLER ON/OFF
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 25
TEST CYCLE START PUSH BUTTON SWITCH
TEST CYCLE STOP PUSH BUTTON SWITCH
VIBRATOR AIR FLOW CONTROL KNOB
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 26
ABRASIVE FLOW CONEVYOR SYSTEM
01. AIR INLET TO ABRASIVE STORAGE HOPPER
02. SEALING DOOR
03. AIR PRESSURE SENSOR
04. STAND OF DISTANCE FOR ABRASIVE FLOW ADJUSTMENT KNOB
05. ABRASIVE STORAGE HOPPER
06. PNEUMATIC VIBRATOR
07. AIR INLET TO PNEUMATIC VIBRATOR
08. LOCKNUT
09. ABRASIVE FLOW NOZZLE
10. ABRASIVE FLOW CONEVYOR
11. SEALING DOOR CLAMPS
12. AIR AND ABRASIVE COMBUSTION CHAMBER
01
02
03
04
05
06
07
08
09
10
11
12
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 27
SPECIMEN HOLDING ARRANGEMENT
01. ANGLE VARIATION KNOB
02. STAND OF DISTANCE ADJUSTMENT
03. X- AXIS MOVEMENT
04. CARBIDE NOZZLE
05. SPECIMEN CLAMPING SCREWS
06. SPECIMEN
07. SPECIMEN HEATER BLOCK
08. Y-AXIS MOVEMENT
03
02
01
04
05
06
07
08
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 28
SPECIMEN AND CLAMPING ARRANGEMENT
01. SPECIMEN CLAMPING FINGERS
02. HEATER BLOCK HOLDER
03. CARBIDE NOZZLE
04. SPECIMEN
05. HEATER BLOCK
02
01
03
04
05
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 29
UNIT FOR HOLDING DOUBLE DISK ARRANGEMENT
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 30
DRY AIR TO TEST RIG AIR INLET FROM COMPRESSOR
AIR DRYER UNIT
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 31
POWER SUPPLY UNIT
01. MAINS ON/OFF
02. POWER CABLE
03. FUSE
02
03
01
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 32
SPECIMEN HOLDING UNIT
01. SAND NOZZLE
02. SPECIMEN HOLDING CLAMPS
03. CLAMPING SCREWS
04. SPECIMEN
05. SPECIMEN HOLDING BLOCK
01
02
03
04
05
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 33
X Y, Z & θ AXIS
01. X-AXIS MOVEMENT
02. Z-AXIS MOVEMENT
03. INDEXING HEAD (0°TO 90° WITH 2° LEAST COUNT)
04. Y-AXIS MOVEMENT
02
03
04
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 34
DOUBLE DISC UNIT HOLDER
DOUBLE DISC ARRANGEMENT
Upper disc with slit
Lower disc
Air jet erosion test rig as per ASTM G76
M/s Magnum Engineers, Peenya, Bangalore
www.magnumengg.com Page 35
top related