advanced digital circuits ecet 146 week 5 professor iskandar hack et 221g, 481-5733 hack@ipfw.edu me...

Advanced Digital CircuitsECET 146

Week 5

Professor Iskandar Hack

ET 221G, 481-5733

hack@ipfw.edu

Me as I typed this slides

This Week’s Goals

Introduction to the concept of Hierarchical Design Techniques

Designing a circuit with multiple projects Designing an counter in AHDL

Hierarchical Design Techniques

Also called Top-Down Design A design technique that allows a project to be

broken into a series of smaller projects Each subdesign is developed and tested

separately The overall design is then assembled using

either Text Design Techniques or by connecting the subdesigns in the graphical editor (preferred method for this course)

Design a four-bit full adder using Hierarchal Techniques Create a project for One-Bit Half Adder

Enter Design Compile Create Default symbol simulate project HA

Create a project for One-Bit Full adder Repeat steps from above

Create a new project fourbitadd in Graphical Editor Insert a half adder and three full adders, and connect

as done in ECET 11 Simulate full design These circuits can be found on pages 236-238 in

ECET 111 textbook

Enter Design for Half Adder

Half Adder

Simulation of HA

Remember steps from earlier lectures

Enter the design using Input Output XOR AND2

Name the pins Save file as ha.gdf Set project to current file Save and Compile (don’t worry about set device or

pins since we’re not going to build the subdesign in hardware)

Draw Waveforms for Simulation and Simulate

Create Default Symbol

This step creates a schematic symbol that can be used in other designs

Default Symbol for Half Adder

Full Adder

Repeat process for the Full Adder that you did for the Half Adder

Simulation for Full Adder

Default Symbol for Full Adder

Draw Four-Bit Adder

Open Graphical Editor and add the symbols ha and 4-fa’s and connect them as shown with inputs and outputs similar as shown on page 238 in Kleitz

Note – All files MUST be in the same directory on the drive!!!

Do not put ha, fa and fourbitadder in different directories.

Fourbitadder drawing

Save, Compile, Define Device and Pins After drawing the fourbitadder save it as a

new file (fourbitadder.gdf) Set Project to current file Save and Compile Set Device as before to EPM74128SLC84-7 Define input pins and output pins

Pin Assignments

Draw Waveforms for Simulation

As before you’ll open the waveform editor and add the nodes from the SNF

Group Inputs and Outputs

Group the inputs and outputs to make verification easy

Change Group Values to Verify Circuit Select part of A[] and B[] and assign them

random values to see if the circuit actually adds the output

Completed Simulation Waveform

Remember that I chose random values for A[0..3] and B[0..3] to test the circuit

Simulate

Save the file as fourbitadder.scf and simulate

Glitches because of propagation delays

Lab 4

Implement an 8-Bit adder as discussed in this lab

Simulate the design Do not Build the circuit, just turn copies of the

HA, FA and eightbitadder GDF files and simulation

Introduction to Finite State Machines

We will only discuss synchronous Finite State Machines (FSM’s)

Synchronous FSM’s will change state only on a rising or falling clock edge

The simplest Finite State Machine (FSM ) is a counter

Every FSM has an input at a minimum a clock and reset

A simple counter the counts from 0 to 5 and repeats has 6 unique states, which I’ll call s0, s1, s2, s3, s4 and s5

A simple counter will change state every clock cycle

A Simple Bubble Graph for Counter

Block Diagram for FSM

State TransitionTable

ClockResetOther Inputs

Current State

Next StateOutputs

Defining State Machines in AHDL

Define Subdesign with Inputs and Outputs as before

Add the state machine definition in the variable section

Use a table to specify the state transitions Use a 2nd table to specify the output for each

state

AHDL Simple Counter Design

Subdesign with I/O specified

Tell Altera to setUp State Machine

Define how to go from CurrentState to Next State

Define what the outputs are forEach state

Save, Set Project and Compile

Repeat steps as done earlier projects Save as

projname.tdf Set Project to

Current File Save and Compile Define Device and

Pins (note Pin 2 is used for clock and Pin 1 for Reset)

Verify Pin Outs in Report File

** PIN/LOCATION/CHIP ASSIGNMENTS **

Actual User Assignments Assignments (if different) Node Name

simplecounter@2 clk simplecounter@54 count0 simplecounter@55 count1 simplecounter@56 count2 simplecounter@1 reset

Simulate

Open Waveform Editor and add nodes from SCF as before

The only inputs are reset and clk in this project

Take the reset high for ½ clock cycle and use the clock function to define the clock

Simulation Waveform

Note the State is Displayed – Very Important forTroubleshooting projects later

Lab 4b

Design a counter in AHDL that will count the sequence 0,1,3,4,5,6,7,2,0,1,3,…

Simulate the Design and turn in the a copy of the TDF file and Simulation

You do not need to build this circuit