2090-series motor/actuator cables for kinetix tlp servo ......2090-ctpb-mcdf-xxfxx 2090-ctpb-mcdf-xx...
Post on 23-Jan-2021
20 Views
Preview:
TRANSCRIPT
-
Product InformationOriginal Instructions
2090-Series Motor/Actuator Cables for Kinetix TLP Servo MotorsCatalog Numbers 2090-CTPW-MADF, 2090-CTPW-MCDF, 2090-CTPW-MDDF, 2090-CTPW-MEDF, 2090-CTPW-MAET, 2090-CTPW-MCET, 2090-CTPW-MDET, 2090-CTPW-MEET, 2090-CTPB-MADF, 2090-CTPB-MCDF, 2090-CTPB-MDDF, 2090-CTPB-MAET, 2090-CTPB-MCET, 2090-CTPB-MDET, 2090-CTBK-MBDF, 2090-CTBK-MBET, 2090-CTFB-MADD, 2090-CTFB-MFDD, 2090-CTFB-MAET, 2090-CTFB-MFET
ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.注意:在安装、配置、操作和维护本产品前,请阅读本文档以及 “其他资源”部分列出的有关设备安装、配置和操作的相应文档。除了所有适用规范、法律和标准的相关要求之外,用户还必须熟悉安装和接线说明。
安装、调整、投运、使用、组装、拆卸和维护等各项操作必须由经过适当训练的专业人员按照适用的操作规范实施。
如果未按照制造商指定的方式使用该设备,则可能会损害设备提供的保护。ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos adicionales acerca de la instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos los códigos, leyes y estándares vigentes.El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el código de práctica aplicable. Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou manter este produto. Os usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e especializado, de acordo com o código de prática aplicável. Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и документы, перечисленные в разделе «Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации данного оборудования. Пользователи обязаны ознакомиться с инструкциями по установке и прокладке соединений, а также с требованиями всех применимых норм, законов и стандартов.Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться обученным персоналом в соответствии с применимыми нормами и правилами.Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.注意 : 本製品を設置、構成、稼動または保守する前に、本書および本機器の設置、設定、操作についての参考資料の該当箇所に記載されている文書に目を通してください。ユーザは、すべての該当する条例、法律、規格の要件に加えて、設置および配線の手順に習熟している必要があります。
設置調整、運転の開始、使用、組立て、解体、保守を含む諸作業は、該当する実施規則に従って訓練を受けた適切な作業員が実行する必要があります。
本機器が製造メーカにより指定されていない方法で使用されている場合、機器により提供されている保護が損なわれる恐れがあります。ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten, bevor Sie dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zusätzlich mit den Installations- und Verdrahtungsanweisungen vertraut machen.Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in Übereinstimmung mit den anwendbaren Ausführungsvorschriften vorgenommen werden.Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant d’installer, configurer, utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois et normes en vigueur.Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de pratique en vigueur.Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.주의 : 본 제품 설치 , 설정 , 작동 또는 유지 보수하기 전에 본 문서를 포함하여 설치 , 설정 및 작동에 관한 참고 자료 섹션의 문서들을 반드시 읽고 숙지하십시오 . 사용자는 모든 관련 규정 , 법규 및 표준에서 요구하는 사항에 대해 반드시 설치 및 배선 지침을 숙지해야 합니다 .
설치 , 조정 , 가동 , 사용 , 조립 , 분해 , 유지보수 등 모든 작업은 관련 규정에 따라 적절한 교육을 받은 사용자를 통해서만 수행해야 합니다 .
본 장비를 제조사가 명시하지 않은 방법으로 사용하면 장비의 보호 기능이 손상될 수 있습니다 .ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione “Altre risorse”, riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti dalle leggi, codici e standard applicabili.Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer listelenmiş dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçaları sökme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama yönetmeliklerine uygun şekilde yapılabilir.Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.注意事項:在安裝、設定、操作或維護本產品前,請先閱讀此文件以及列於「其他資源」章節中有關安裝、設定與操作此設備的文件。使用者必須熟悉安裝和配線指示,並符合所有法規、法律和標準要求。
包括安裝、調整、交付使用、使用、組裝、拆卸和維護等動作都必須交由已經過適當訓練的人員進行,以符合適用的實作法規。
如果將設備用於非製造商指定的用途時,可能會造成設備所提供的保護功能受損。POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně instalace, konfigurace a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů a norem nutně seznámit také s pokyny pro instalaci a elektrické zapojení.Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe źródła omawiające instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania, jak również z obowiązującymi kodeksami, prawem i normami.Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel zgodnie z obowiązującym kodeksem postępowania.Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller börjar använda eller utföra underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och standarder.Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product installeert, configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en normen.Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en in overeenstemming met de geldende praktijkregels.Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.
-
2090-Series Motor/Actuator Cables for Kinetix TLP Servo Motors
SpecificationsThese cable pinouts apply to 2090-Series motor cables for Kinetix® TLP servo motors.
Power Cables with and without Brake Pinouts (18, 16, 12, 8, 6, 4 AWG)
Brake Only Cable Pinout
Feedback Cable Pinouts (premolded connector)
ATTENTION: To avoid electrical shock, make sure that shielded power cables are grounded at a minimum of one point. To prevent the buildup of electrical energy, factory-supplied power cables use one of these grounding techniques:• The overall shield is bonded to the connector housing.• A section of the overall shield is exposed for connection to ground.• The overall shield is connected to a ground wire.
If the exposed cable braid or a ground wire is present, connect it to the power cable clamp, housing, or another suitable chassis ground on the drive.ATTENTION: Do not tightly gather or coil the excess length of a power cable. Heat is generated within a cable whenever power is applied. Always position a power cable so it can freely dissipate heat.Do not coil a power cable except for temporary use when building or testing a machine. If you temporarily coil a power cable, you must also derate the cable to meet local code or follow an authoritative directive, such as Engineering Section 310.15(C) of the NEC Handbook.
To DriveUVW
PE
BR+BR-
Green/YellowShield/Drain
RedBlackFoil
D/FE/IF/BG/E
A/G B/H
Green
To Motor
Conductive Connector Housing
Shield-to-ground connections require
ShieldWire Connection
A H G
FIB
C DE
ABC
F E D
GHI
To DriveUVWBR+BR-
PE
A/1B/2C/4 /3 /6D/5
Green
To Motor
Conductive Connector Housing Shield-to-ground connections required.
ShieldWire Connection Twisted Wire Pair
21 34 5 6
A
B C
D BrownBlue
Green/YellowShield/Drain
2090-CTPW-MEDF-xxFxx2090-CTPW-MEDF-xxAxx
6 and 4 AWG Cables
2090-CTPW-MADF-xxFxx 2090-CTPW-MADF-xxAxx2090-CTPB-MADF-xxFxx 2090-CTPB-MADF-xxAxx18 and 16 AWG Cables
2090-CTPW-MCDF-xxFxx2090-CTPW-MCDF-xxAxx2090-CTPB-MCDF-xxFxx2090-CTPB-MCDF-xxAxx16 and 12 AWG Cables
2090-CTPW-MDDF-xxFxx2090-CTPW-MDDF-xxAxx2090-CTPB-MDDF-xxFxx2090-CTPB-MDDF-xxAxx
12 and 8 AWG Cables
2090-CTPW cables exclude (BR+/BR–) motor brake conductors.
2090-CTPW cables exclude (BR+/BR–) motor brake conductors.
BR-BR+
ABA B
BlackRedFoil
Foil2090-CTBK-MBDF-20Fxx2090-CTBK-MBDF-20Axx
To Motor
To Brake Power Supply
Feedback Cable Type Cable Cat. No.
Feedback cables(standard, non-flex)
2090-CTFB-MADD-CFAxx
2090-CTFB-MFDD-CFAxx
Feedback cables(continuous-flex)
2090-CTFB-MADD-CFFxx
2090-CTFB-MFDD-CFFxx
BlackRed
BrownBlue
White/RedWhite
Shield/Drain
BAT-BAT+
5VGND
T-T+
146
105
D/5C/2S/7R/8B/4A/1L/9
To DriveTo Motor BatteryBox
Conductive Connector Housing
Shield Twisted Wire PairWire Connection
41 7
8
93
5
6
2
A MLK
NTS
JHGF
RP
BC
DE
116
1
15105
2090-CTFB-MFDD-CFxxxConnector to Motor
2090-CTFB-MADD-CFxxxConnector to Motor 2090-CTFB-MFDD-CFxxx
2090-CTFB-MA DD-CFxxxConnector to Drive
2 Rockwell Automation Publication 2090-PC006A-EN-P - September 2019
-
2090-Series Motor/Actuator Cables for Kinetix TLP Servo Motors
Power Extension Cables with and without Brake Pinouts (18, 16, 12, 8, 6, 4 AWG)
Brake Only Extension Cable Pinout
Feedback Extension Cable Pinouts
2 21 13 3
4 45 56 6
AD
C BCB
A D
ABC
F E D
GHI
A B C
FED
G H I
AHGF I B
CDE
A H G
FIBC D E
2090-CTPW-MEET-xxFxx6 AWG and 4 AWG Cables
2090-CTPW-MAET-xxFxx 2090-CTPB-MAET-xxFxx
18 AWG and 16 AWG Cables
2090-CTPW-MCET-xxFxx2090-CTPB-MCETxxFxx
16 AWG and 12 AWG Cables
2090-CTPW-MDET-xxFxx2090-CTPB-MDET-xxFxx
12 AWG and 8 AWG Cables
A/1B/2C/4
36
D/5
BrownBlue
Green/YellowShield/Drain
A/1B/2C/4
36
D/5
Motor Plug Extension Plug
Shield Twisted Wire PairWire Connection
Extension Plug
Green/YellowShield/Drain
RedBlackFoil
D/FE/IF/BG/E
A/G B/H
To Motor
ShieldWire Connection
D/FE/IF/BG/E
A/G B/H
2090-CTPW-MAET and 2090-CTPW-MEET cables exclude the Brown and Blue conductors.
2090-CTPW-MCET and 2090CTPW-MDET cables exclude the Red and Black twisted pair conductors.
ABA B
AB
BlackRedFoil
AB
Extension PlugMotor Plug
Wire Connection Foil
2090-CTBK-MBET-20Fxx
A ML
TNB
C
D
P
R
E
SK
JH
GF
AML
TN
BC
DP
R ESK
JH G F
BlackRed
BrownBlue
White/RedWhite
Shield/Drain
BAT-BAT+
5VGND
T-T+
D/5C/2S/7R/8B/4A/1L/9
D/5C/2S/7R/8B/4A/1L/9
Extension PlugEncoder Plug
Connector Back ShieldConnector Back Shield
Shield Twisted Wire PairWire Connection
3 1
9 7
31
97
2090-CTFB-MFET-CFFxx
2090-CTFB-MAET-CFFxx
Rockwell Automation Publication 2090-PC006A-EN-P - September 2019 3
-
Additional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.
You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page.
Rockwell Automation SupportUse the following resources to access support information.
Documentation FeedbackYour comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.
Technical Support Center Knowledgebase Articles, How-to Videos, FAQs, Chat, User Forums, and Product Notification Updates. https://rockwellautomation.custhelp.com/
Local Technical Support Phone Numbers Locate the phone number for your country. http://www.rockwellautomation.com/global/support/get-support-now.page
Direct Dial Codes Find the Direct Dial Code for your product. Use the code to route your call directly to a technical support engineer. http://www.rockwellautomation.com/global/support/direct-dial.page
Literature Library Installation Instructions, Manuals, Brochures, and Technical Data. http://www.rockwellautomation.com/global/literature-library/overview.page
Product Compatibility and Download Center (PCDC)
Get help determining how products interact, check features and capabilities, and find associated firmware. http://www.rockwellautomation.com/global/support/pcdc.page
Resource Description
Kinetix Rotary Motion Specifications, publication KNX-TD001 Provides product specifications for Kinetix VP (Bulletin VPL, VPC, VPF, VPH, VPS), MP-Series™ (Bulletin MPL, MPM, MPF, MPS), TL-Series™, and HPK-Series™ rotary motors.
Kinetix Linear Motion Specifications, publication KNX-TD002 Provides product specifications for LDAT-Series linear thrusters, Bulletin MPAS and MPMA linear stages, Bulletin MPAR and MPAI electric cylinders, and LDC-Series™ and LDL-Series™ linear motors.
Kinetix Servo Drives Specifications, publication KNX-TD003 Provides product specifications for Kinetix Integrated Motion over the EtherNet/IP™ network, Integrated Motion over Sercos interface, EtherNet/IP networking, and component servo drive families.
Kinetix Motion Accessories Specifications, publication KNX-TD004 Provides product specifications for Bulletin 2090 motor and interface cables, low-profile connector kits, drive power components, and other servo drive accessory items.
Kinetix Motion Control Selection Guide, publication KNX-SG001 Provides overview of Kinetix servo drives, motors, actuators, and motion accessories that are designed to help make initial decisions for the motion control products best suited for your system requirements.
2090-Series Motor Cables for Kinetix TLP Servo Motors Installation Instructions, publication 2090-IN046
Provides installation information and cable specifications for Bulletin 2090 motor/actuator cables for Kinetix TLP servo motors.
Kinetix 5100 Single-axis EtherNet/IP Servo Drive User Manual, publication 2198-UM004 Provides information on applications and how to install, configure, startup, and troubleshoot your Kinetix servo drive system.
System Design for Control of Electrical Noise Reference Manual, publication GMC-RM001 Information, examples, and techniques that are designed to minimize system failures caused by electrical noise.
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for the installation of a Rockwell Automation industrial system.
Product Certifications website: rok.auto/certifications Provides declarations of conformity, certificates, and other certification details.
Allen-Bradley, HPK-Series, Kinetix, LDC-Series, LDL-Series, MP-Series, Rockwell Automation, Rockwell Software, and TL-Series are trademarks of Rockwell Automation, Inc.EtherNet/IP is a trademark of ODVA, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Publication 2090-PC006A-EN-P - September 2019Copyright © 2019 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
https://literature.rockwellautomation.com/idc/groups/literature/documents/td/knx-td001_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/td/knx-td002_-en-p.pdfhttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.pagehttps://literature.rockwellautomation.com/idc/groups/literature/documents/in/2090-in046_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/um/2198-um004_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/rm/gmc-rm001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttps://rok.auto/certificationshttp://www.rockwellautomation.com/global/literature-library/overview.pagehttps://literature.rockwellautomation.com/idc/groups/literature/documents/td/knx-td003_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/td/knx-td004_-en-p.pdfhttps://literature.rockwellautomation.com/idc/groups/literature/documents/sg/knx-sg001_-en-p.pdf
2090-Series Motor/Actuator Cables for Kinetix TLP Servo MotorsSpecificationsPower Cables with and without Brake Pinouts (18, 16, 12, 8, 6, 4 AWG)Brake Only Cable PinoutFeedback Cable Pinouts (premolded connector)Brake Only Extension Cable PinoutFeedback Extension Cable Pinouts
Additional Resources
Print Spec Sheet
RA-QR005K-EN-PJan-19
Printing SpecificationYOUR DATA HEREInstructionsNO
(required) Publication Number:2090-PC006A-EN-PSample: 2030-SP001B-EN-P11” x 17”LOOSE -Loose LeafYESPre-sale / MarketingTOP
Use Legacy Number:YES or NO8.5” x 11”PERFECT - Perfect BoundA1LEFT
Legacy Number if applicable:Sample Legacy Number: 0160-5.338.375” x 10.875SADDLE - Saddle StitchA2RIGHTCORNER
Publication Title:2090-Series Motor/Actuator Cables for Kinetix TLP Motors Product InformationSample: ElectroGuard Selling Brief80 character limit - must match DocMan Title8.25” x 11” (RA product profile std)PLASTCOIL - Plastic Coil (Coil Bound)A4BOTTOMSIDE
Used in Manufacturing:YESYES or NO - If Yes, must have Part No. listed below8.25” x 10.875”STAPLED1 -1 positionA3
Part Number:5014097500-QL00If SAP Part Number, be sure to enter PN- before the number7.385” x 9” (RSI Std)STAPLED1B - bottom 1 positionA5
(required) CategoryD5Select Print Category A,B,C or D from category list, on "Introduction_Category Types" tab6” x 4”STAPLED2 - 2 positionsA6
Paper Stock Color:White is assumed. For color options contact your vendor5.5” x 8.5” (half-size)THERMAL - Thermal bound (Tape bound)A7
Ink Color:One color assumes BLACK / 4 color assume CMYK / Indicate PMS number here4.75” x 7.75”THERMALO - Thermal Bound (Tape bound - offline)A8
(required) Page Count ofPublication:4Total page count including cover. Enter PAGE count, not SHEET count4.75” x 7” (slightly smaller half-size)A9
(required) Finished Trim Size Width:8.5” x 11”This is sheet size, before folding4.25" x 5.50"Post Sale / Technical Communication
Fold:Half or V or Single FoldReview key below. Leave blank if folded for saddle stitching4” x 6”B1
Finished Fold Size:5.5 x 4.25This is size after folding is completed3” x 5”B2
Binding/Stitching:SADDLE - Saddle StitchReview key below9” x 12” (Folder)B3None
Stitching Location:Blank, Corner or SideA4 (8 ¼” x 11 ¾”) (210 x 297 mm)B4Half or V or Single Fold
Drill Hole (Yes/No):All drilled publications use the 5-hole standard, 5/16 inch-size hole and a minimum of ¼ inch from the inner page border.A5 (5.83” x 8.26”) (148 x 210 mm)B5C or Tri-Fold
Number of Tabs Needed:5 tab in stock at RR Donnelley36” x 24” PosterCatalogsDbleParll
Number of Pages per Pad:Average sheets of paper. 25, 50 75,100 Max24” x 36” PosterC1Sample
Glue Location on Pad:Glue location on pads18” x 24” PosterC2Short (must specify dimensions between folds in Comments)
Comments:Print on Demand (POD)Double Gate
Saddle-Stitch Items All page quantities must be divisible by 4.Note: Stitching is implied for Saddle-Stitch -no need to specify in Stitching Location.80 pgs max. on 20# (text and cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24# (text and cover)
Perfect Bound Items940 pgs max. w/cover (90# index unless indicated otherwise)70 pgs. min. for spine without words200 pgs min. for spine with words
Plastic Coil Bound Items530 pgs max. of 20# (if adding cover deduct equivalent number of pages to equal cover thickness) (90# index unless indicated otherwise)
Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover (90# index unless indicated otherwise)D1
D2
D5
D6
&LPrint Specifications
&LRockwell Automation Publication RA-QR005K-EN-P&RJanuary 2019
Introduction_Category Types
This tab summarizes Rockwell Automation Global Sales and Marketing preferred printing standards. It also provides guidance on whether a publication should be released print on demand or if it requires an RFQ for offset printing.Find your publication type in the first section below. Use the assigned Printing Category information to determine the standard print specifications for that document type. The Printing Categories are defined below the Publication Type section. Note there may be slightly different print specifications for the categories, depending on the region (EMEA or Americas).For more information on Global Sales and Marketing Printing Standards, see publication RA-CO004 in DocMan.
Publication Type and Print Category
Publication TypeOff Set Print Category Spec. (See tables below)Print on Demand Spec. (See tables below)DescriptionOrder Min **Order Max **Life Cycle Usage / Release Option
ADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale / Internal
APA3D2Application Solution or Customer Success Story5100Presale / External
ARNANAArticle/Editorial/BylineNANAPresale / Internal
(press releases should not be checked into DocMan or printed)
ATB3, B4D5Application techniques5100Presale / External
BRA2 Primary, A1NABrochures5100Presale / External
CAC2 Primary, C1NACatalogue150Presale / External
CGNANACatalogue Guide150Presale / External
CLNANACollection550Presale / External
COA5, A6, A9D5Company Confidential InformationNANANA / Confidential
CPE-onlyE-only, D5Competitive Information550NA / Confidential
DCE-onlyE-onlyDiscount SchedulesNANAPresale / Internal
DIA1, A3NADirect Mail5100Presale / Internal
DMNANAProduct Demo550Presale / Internal
DSB3D5Dimensions Sheet15Post / External
DUB3D5Document Update15Post / External
GRB2D6Getting Results15Post / External
INB3 Primary, B2D5, D6Installation instructions15Post / External
LMNANALaunch Materials550Presale / Internal
PCB3D5Packaging Contents
PLE-only primary, B3E-onlyPrice List550Presale / Internal
PMB2D6Programming Manual15Post / External
PPA3D1Profile (Single Product or Service). NOTE: Application Solutions are to be assigned the AP pub type.5100Presale / External
QRB2 primary, B3, B5D5, D6Quick Reference15Post / External
QSB2 primary, B3, B5D5, D6Quick Start15Post / External
RMB2D5, D6Reference Manual15Post / External
RNB3D5Release Notes15Post / External
SGB1 Primary, B4D5, D6Selection Guide Colour550Presale / External
SGB2D5, D6Selection Guide B/W550Presale / External
SPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to be assigned the PP pub type.5100Presale / Internal
SRB2, B3D5, D6Specification Rating Sheet5100Presale / External
TDB2 Primary B3, B4, B5D5, D6Technical Data550Presale / External
TGB2, B3D6Troubleshooting Guide15Post / External
UMB2 Primary, B4D6User Manual B/W15Post / External
WDB3D5Wiring Diagrams / Dwgs15Post / Internal
WPB3 Primary, B5D5White Paper550Presale / External
** Minimum order quantities on all POD items are based on the publication length. **
Publication lengthMinimum Order Quantity
77 or more pages1 (no shrink wrap required)
33 to 76 pages25
3 to 32 pages50
1 or 2 pages100
Pre-sale / Marketing
All paper in this category is White Brightness, 90% or better. Opacity 90% or better
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements
A14 color170 gsm 2pp100# gloss cover, 100# gloss text
A24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss text
A34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss cover, 80# gloss text
A42 color170gsm Silk – 120gsm Silk80# gloss cover, 80# gloss text
A52 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text
A61 color170gsm Silk – 120gsm Silk80# gloss cover, 80# matt sheet text
A74 color cover2 color textSelection GuideCategory being deleted10 Point Cover C2S50# matte sheet text
A84 color coverCategory being deleted50# matte sheet text, self cover
2 color text
Selection Guide
A92 color100gsm bond50# matte sheet text, self cover
Selection Guide
Gray shading indicates Obsolete Print Catagories
Post Sale / Technical Communication
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements
B14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S
2 color text50# matte sheet text
B21 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text
B31 color100gsm bond50# matte sheet text, self cover
B42 color160gsm Colortech & 100gsm Bond90# Cover50# matte sheet text
B52 color100gsm bond50# matte sheet text, self cover
Catalogs
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements
C14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S
4 color text45# Coated Sheet
C24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S
2 color text32#-33# Coated Sheet
Print on Demand by Print Vendor (POD)
All paper in this category is White Brightness, 82% or better. Opacity 88% or better
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US Paper Requirements
D14 color170gsm white silk80# gloss cover, coated 2 sides
D24 color120gsm white silk80# gloss text, coated 2 sides, self cover
D34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss text coated 2 sides
D41 color160gsm tab90# index
D51 color80gsm bond20# bond, self cover
D61 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond
D72 color160gsm tab90# index
D82 color80gsm bond20# bond, self cover
D92 colorCover 160gsm tab with Body 80gsm bond90# index, 20# bond
D10Combination: 4 color cover, with 2 color bodyCover 160gsm with Body 80gsm90# index, 20# bond
Gray shading indicates Obsolete Print Catagories
Print on Demand By Print Vendor (POD) or Off Set (OS)?
Use these guidelines to determine if your publication should be print on demand by print vendor (POD) or if it would be more economical to print ffset/on a press (OS). OS print jobs require an RFQ (Request For Quote) in US. If your job fits into the “Either” category, an RFQ is recommended, but not required. In the US, RA Strategic Sourcing will discourage or reject RFQs for jobs that fall within the POD category. Guidelines differ for black & white and color printing, so be sure to check the correct tables.
&LPrint Specifications
&LRockwell Automation Publication RA-QR005K-EN-P&RJanuary 2019
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Average /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages false /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Average /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False
/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice
top related