116378093 ericsson msc commands
Post on 13-Apr-2015
554 Views
Preview:
TRANSCRIPT
CDLCP
© Telefonaktiebolaget LM Ericsson 2001
Call Duration Supervision, Long Duration Call, Print
1 Format
1.1 Command
CDLCP;
1.2 Parameters
This command has no parameters.
2 Function
The command CDLCP initiates the printout LONG DURATION CALL SUPERVISION DATAthat
lists the set-up data of the function time supervision and disconnection of long duration calls
and whether automatic disconnection is initiated.
The order does not remain after system restart.
3 Examples
3.1 Example 1
CDLCP;
The command results in an answer printout being issued.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED
fault type
Fault type:
FUNCTION BUSY
The function is busy.
FORMAT ERROR
The command or a parameter was incorrectly specified.
FAULT CODE 10 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
The functionality addressed by the command is not supported by this exchange.
4.3 Answer Printouts
LONG DURATION CALL SUPERVISION DATA
4.4 Result Printouts
This command has no result printouts.
© Telefonaktiebolaget LM Ericsson 1998
Transmission Function Synchronous Digital Path, State, Print
1 Format
1.1 Command
/ \
|SDIP=sdip... |
TPSTP:[IO=io,]+ +;
|SDIP=ALL[,STATE=state...]|
\ /
1.2 Parameters
IO=io Input/Output (IO) device name
Identifier 1 - 7 characters
SDIP=sdip Synchronous Digital Path (SDIP) name
Identifier 1 - 7 characters ALL
All SDIPs
STATE=state State of SDIP BLOC
Blocked PBLOC
Partly blocked TRAFBLOC
Traffic blocked TRAFLIM
Traffic limited WO
Working
2 Function
This command prints the state of specified SDIP on specified or default IO device.
Printout SYNCHRONOUS DIGITAL PATH STATE is received.
Up to 10 SDIPs can be specified in each command.
The order does not remain after system restart.
3 Examples
3.1 Example 1
TPSTP:SDIP=LONDON;
The state of SDIP LONDON is printed.
3.2 Example 2
TPSTP:IO=AT-4,SDIP=LONDON&OSLO;
The state of the SDIPs LONDON and OSLO is printed on IO device AT-4.
3.3 Example 3
TPSTP:SDIP=ALL;
The state of all SDIPs is printed.
3.4 Example 4
TPSTP:IO=AT-4,SDIP=ALL,STATE=WO&BLOC;
All working and all blocked SDIPs are printed on IO device AT-4.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
ORDERED
NOT ACCEPTED
fault type
Fault type:
FUNCTION BUSY
The function is busy.
FORMAT ERROR
details
The command or a parameter was incorrectly specified.
UNREASONABLE VALUE
details
The parameter was specified with an unreasonable value.
FAULT CODE 2 SDIP DOES NOT EXIST
details
The specified SDIP does not exist.
FAULT CODE 3 ALL IS NOT ACCEPTED AS AN SDIP NAME
"ALL" is not accepted as a SDIP name.
FAULT CODE 4 NO SDIPS EXIST
No SDIPs exist.
FAULT CODE 5 TOO MANY SDIPS SPECIFIED
Too many SDIPs are specified.
4.3 Answer Printouts
SYNCHRONOUS DIGITAL PATH STATE
4.4 Result Printouts
SYNCHRONOUS DIGITAL PATH STATE
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
Telefonaktiebolaget LM Ericsson 2000
Transcoder Pool Resource Data, Print
1 Format
1.1 Command
/ \
|ALL |/ / \\
TKPRP:TRAPOOL=+ +|,DETAILS|,BLOC||;
|trapool...|\ \ //
\ /
1.2 Parameters
BLOC Blocked transcoder pool resources
Specifies that only the blocked transcoder resources belonging to the
transcoder pool are printed.
DETAILS Detail resources
Specifies that all the resources belonging to the transcoder pool are
printed.
TRAPOOL=trapool Transcoder pool
Identifier 1 - 7 characters
2 Function
This command initiates a printout of transcoder pool data for the specified transcoder pools.
The data is presented in the answer printout TRANSCODER POOL RESOURCE DATA. If
parameter DETAILS is specified in the command, all the transcoder resources connected to
the pool are printed with their resource state. If parameter BLOC is specified in the
command, only the blocked transcoder resources connected to the pool are printed.
The order does not remain after system restart.
3 Examples
3.1 Example 1
TKPRP:TRAPOOL=UAMR;
The transcoder pool data for the pool UAMR is printed.
3.2 Example 2
TKPRP:TRAPOOL=UAMR,DETAILS;
The transcoder pool data for the pool UAMR is printed. A list of all transcoder resources in
the pool is printed.
3.3 Example 3
TKPRP:TRAPOOL=UAMR,DETAILS,BLOC;
The transcoder pool data for the pool UAMR is printed. A list of all the transcoder devices in
the pool that are blocked is printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED
fault type
Fault type:
FUNCTION BUSY
The function is busy.
FORMAT ERROR
The command or a parameter was incorrectly specified.
UNREASONABLE VALUE
details
The parameter was specified with an unreasonable value.
FAULT CODE 4 TRANSCODER POOL NAME DOES NOT EXIST
details
The transcoder pool to be printed does not exist.
FAULT CODE 35 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
Optional feature transcoder service not supported by this exchange.
4.3 Answer Printouts
TRANSCODER POOL RESOURCE DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
SQTLP
SERVICE QUALITY STATISTICS TIME LIMITS, PRINT
1 Format
1.1 Command
SQTLP;
1.2 Parameters
-
2 Function
The command requests printout of the time limits for
post-dialling delay,time to B-answer and conversation
time. These times are specified with command SQTLI.
The order does not remain after system restart.
3 Examples
3.1 Example
SQTLP;
The time limits for post-dialling delay,B-answer
and conversation time will be printed.
SQREP
SERVICE QUALITY STATISTICS RESULT, PRINT
1 Format
1.1 Command
/ / \\
| |DETAILED||
SQREP:MP=mp|,+ +|;
| |SURVEY ||
\ \ //
1.2 Parameters
DETAILED Detailed answer printout
MP=mp Measuring program identity (Numeral)
The number of measuring programs is size
alterable.
See Application Information for block SEQS3.
SURVEY Survey answer printout
2 Function
The command requests a printout of the current service
quality statistics which is received as an answer
printout. If there is no result output period in
progress the previous result output period results
will be printed.
The answer printout can be detailed or survey. If
the parameter DETAILED or SURVEY is omitted the answer
printout type will be survey. The detailed answer
printout shows all events. Time limits (PDD, BANSWER,
CTIME) which have not been specified are not shown.
The survey answer printout is presented in main groups,
and events that have not got any registrations will
not be included in this printout.
The results are presented in the printout SERVICE
QUALITY STATISTICS RESULT and the printout SERVICE
QUALITY STATISTICS RESULT SURVEY.
The order does not remain after system restart.
3 Examples
3.1 Example 1
SQREP:MP=6;
A subresult received as an answer printout is
requested for measuring program 6.
The answer printout type is survey.
3.2 Example 2
SQREP:MP=7,DETAILED;
A subresult received as an answer printout is
requested for measuring program 7.
The answer printout type is detailed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED fault type
Fault type:
FORMAT ERROR
Format error
UNREASONABLE VALUE
details Unreasonable value
FAULT CODE 16
SPECIFIED MP IS NOT DEFINED FOR THE FUNCTION
The specified measuring program
is not defined for the function.
FAULT CODE 17
THE FIRST RECORDING PERIOD HAS NOT STARTED
The first recording period has
not started.
FAULT CODE 24
BUFFER FOR OUTPUT NOT AVAILABLE
Buffer for output is not available.
Give the command again.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS RESULT
SERVICE QUALITY STATISTICS RESULT SURVEY
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0).
7 Command Receiving Block
COMMAND DESCRIPTION 3/190 82-CNT 216
1205 Uen A1
SQMPP
SERVICE QUALITY STATISTICS MEASURING PROGRAM, PRINT
1 Format
1.1 Command
/ \
|mp...|
SQMPP:MP=+ +;
|ALL |
\ /
1.2 Parameters
mp Measuring program identity.
ALL All measuring
programs defined in the function.
2 Function
The command requests output of data for one or several
measuring programs and of the number of idle measuring
programs.
The order does not remain after system restart.
3 Examples
3.1 Example 1
SQMPP:MP=1&3;
Printout of measuring programs 1 and 3 is requested.
3.2 Example 2
SQMPP:MP=ALL;
Printout of all measuring programs is requested.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED fault type
Fault type:
FORMAT ERROR
Formal format fault in relation to the command description.
UNREASONABLE VALUE
details Unreasonable values, overaddressing.
FAULT CODE 16
details
The specified measuring program
is not defined for the function.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS MEASURING PROGRAM
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H' 0 ).
7 Command Receiving Block
SEQS2
COMMAND DESCRIPTION 2/190 82-CNT 216 1470 Uen B
SQESP
Service Quality Statistics Connection of End-of- Selection Codes, Print
1 Format
1.1 Command
/ \
|event...|
SQESP:EVENT=+ +;
|ALL |
\ /
1.2 Parameters
EVENT=event Event group
ALL All event groups
The following events are possible:
GROUP 1:
ARBDAD A-replacement
before, during or after dialling
BBUSY B-subscriber
busy
BNOEX B-number does
not exist
BOUT B-number out of
order
CONGGS Congestion in
group switch
CONGJT Congestion in
junctor terminals
CONGNW Congestion in
the network (that is, in the next
exchange)
CONGOT Congestion
in outgoing trunk (last choice route)
CONGTS Congestion in
time switch. (in the digital
subscriber switch)
EOSNOSE End-of
selection codes not connected to any
specified event group
FSIGCR Faulty signal
received in code receiver
FSIGCS Faulty
signal received in code sender
FSIGIT Faulty signal
received in incoming trunk
FSIGOT Faulty signal
received in outgoing trunk
HWFCR Hardware
fault in code receiver
HWFCS Hardware
fault in code sender
HWFJT Hardware fault
in junctor terminals
HWFIT Hardware fault
in incoming trunk
HWFOT Hardware fault
in outgoing trunk
HWFTS Hardware fault
in the time switch. (in the digital
subscriber switch)
NMBLO Calls blocked
due to Network Management actions
TOBDD Time out
before or during dialling
TOCS Time out in
code sender
TOOT Time out in
outgoing trunk
SPARE1 For own use
SPARE2 For own use
SPARE3 For own use
. .
. .
. .
SPARE16 For own use
GROUP 2:
RESHF Hardware fault
in speech position
RESSF Signalling
fault in speech position
2 Function
Command SQESP requests a printout of specified event
groups with the corresponding end-of-selection
codes.
The printout SERVICE QUALITY STATISTICS
END-OF-SELECTION CODES PER EVENT is received in
answer to this command.
The order does not remain after system restart.
3 Examples
3.1 Example 1
SQESP:EVENT=BBUSY&BOUT&BNOEX;
The corresponding end-of-selection codes will
be printed for the following event groups:
- B-subscriber busy
- B-number out of order
- B-number does not exist
3.2 Example 2
SQESP:EVENT=EOSNOSE;
The end-of-selection codes which are not
connected to any event group will be printed.
3.3 Example 3
SQESP:EVENT=ALL;
End-of-selection codes will be printed for all
event groups.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED fault type
Fault type:
FORMAT ERROR
Format error.
UNREASONABLE VALUE
details Unreasonable value.
FAULT CODE 26
EVENT CANNOT BE SPECIFIED WITH THIS APPLICATION SYSTEM
If the application parameter
HFANDSFALLOWED is not set, then
events RESHF and RESSF are not
allowed for the function.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS END-OF-SELECTION CODES PER EVENT
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0).
7 Command Receiving Block
SEQS1
COMMAND DESCRIPTION 2/190 82-CNT 216
1470 Uen B
SQESP
Service Quality Statistics Connection of End-of- Selection Codes, Print
1 Format
1.1 Command
/ \
|event...|
SQESP:EVENT=+ +;
|ALL |
\ /
1.2 Parameters
EVENT=event Event group
ALL All event groups
The following events are possible:
GROUP 1:
ARBDAD A-replacement
before, during or after dialling
BBUSY B-subscriber
busy
BNOEX B-number does
not exist
BOUT B-number out of
order
CONGGS Congestion in
group switch
CONGJT Congestion in
junctor terminals
CONGNW Congestion in
the network (that is, in the next
exchange)
CONGOT Congestion
in outgoing trunk (last choice route)
CONGTS Congestion in
time switch. (in the digital
subscriber switch)
EOSNOSE End-of
selection codes not connected to any
specified event group
FSIGCR Faulty signal
received in code receiver
FSIGCS Faulty
signal received in code sender
FSIGIT Faulty signal
received in incoming trunk
FSIGOT Faulty signal
received in outgoing trunk
HWFCR Hardware
fault in code receiver
HWFCS Hardware
fault in code sender
HWFJT Hardware fault
in junctor terminals
HWFIT Hardware fault
in incoming trunk
HWFOT Hardware fault
in outgoing trunk
HWFTS Hardware fault
in the time switch. (in the digital
subscriber switch)
NMBLO Calls blocked
due to Network Management actions
TOBDD Time out
before or during dialling
TOCS Time out in
code sender
TOOT Time out in
outgoing trunk
SPARE1 For own use
SPARE2 For own use
SPARE3 For own use
. .
. .
. .
SPARE16 For own use
GROUP 2:
RESHF Hardware fault
in speech position
RESSF Signalling
fault in speech position
2 Function
Command SQESP requests a printout of specified event
groups with the corresponding end-of-selection
codes.
The printout SERVICE QUALITY STATISTICS
END-OF-SELECTION CODES PER EVENT is received in
answer to this command.
The order does not remain after system restart.
3 Examples
3.1 Example 1
SQESP:EVENT=BBUSY&BOUT&BNOEX;
The corresponding end-of-selection codes will
be printed for the following event groups:
- B-subscriber busy
- B-number out of order
- B-number does not exist
3.2 Example 2
SQESP:EVENT=EOSNOSE;
The end-of-selection codes which are not
connected to any event group will be printed.
3.3 Example 3
SQESP:EVENT=ALL;
End-of-selection codes will be printed for all
event groups.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED fault type
Fault type:
FORMAT ERROR
Format error.
UNREASONABLE VALUE
details Unreasonable value.
FAULT CODE 26
EVENT CANNOT BE SPECIFIED WITH THIS APPLICATION SYSTEM
If the application parameter
HFANDSFALLOWED is not set, then
events RESHF and RESSF are not
allowed for the function.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS END-OF-SELECTION CODES PER EVENT
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0).
7 Command Receiving Block
SEQS1
COMMAND DESCRIPTION 6/190 82-CNT 298 0026 Uen B
NRGGP
© Telefonaktiebolaget LM Ericsson 2001
Network Resourcing, Media Gateway Group, Print
1 Format
1.1 Command
/ \
|mgg...|
NRGGP:MGG=+ +;
|ALL |
\ /
1.2 Parameters
MGG=mgg Media gateway group
Text string 1 - 7 characters ALL
All defined Media Gateway Groups (MGG)s.
2 Function
This command orders a printout with information about a specific or all the defined MGGs.
When parameter MGG is assigned with a name of a specific MGG, only data for the specified
MGG are printed. When it is assigned with the value ALL, data for all defined MGGs are
printed.
Answer printout MEDIA GATEWAY GROUP DATA is received.
The order does not remain after system restart.
3 Examples
3.1 Example 1
NRGGP:MGG="MGG4GBR"&"MGG3GR";
Information about media gateway groups "MGG4GBR" and "MGG3GR" are printed.
3.2 Example 2
NRGGP:MGG=ALL;
Information about all defined media gateway groups are printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED
fault type
Fault type:
FORMAT ERROR
The command or a parameter was incorrectly specified.
UNREASONABLE VALUE
details
The parameter was specified with an unreasonable value.
FAULT CODE 10 THE SPECIFIED MGG HAS NOT BEEN DEFINED
The specified MGG has not been defined.
FAULT CODE 14 FUNCTIONALITY NOT SUPPORTED BY THE APPLICATION
The functionality is not supported by the application.
FAULT CODE 26 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
The functionality is not supported by this exchange.
4.3 Answer Printouts
MEDIA GATEWAY GROUP DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 00 (H'00)
7 Command Receiving Block
NRM
8 Glossary
MGG Media Gateway Group
9 References
9.1 Printout Descriptions
MEDIA GATEWAY GROUP DATA
COMMAND DESCRIPTION 3/190 82-CNT 238
0164 Uen A
HGSTP
© Telefonaktiebolaget LM Ericsson 1999
Home Location Register, Subscriber Tracing, Print
1 Format
1.1 Command
/ \
|imsi|
HGSTP:IMSI=+ +;
|ALL |
\ /
1.2 Parameters
IMSI=imsi International Mobile Subscriber Identity (IMSI)
See the Application Information for block HTRAN.
ALL
All IMSI with initiated trace data
2 Function
This command prints the trace data for mobile subscribers in Home Location Register (HLR).
Answer printout HLR SUBSCRIBER TRACING DATA is received.
This command can be initiated from up to 16 Input/Output (IO) devices simultaneously.
Only one command can be initiated when parameter ALL is specified.
The order does not remain after system restart.
3 Examples
3.1 Example 1
HGSTP:IMSI=ALL;
The trace data for all mobile subscribers, are printed.
3.2 Example 2
HGSTP:IMSI=1234567890;
The trace data for IMSI 1234567890 are printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED
fault type
Fault type:
FUNCTION BUSY
The function is busy.
FORMAT ERROR
The command or a parameter was incorrectly specified.
UNREASONABLE VALUE
details
The parameter was specified with an unreasonable value.
FAULT CODE 13 IMSI NOT DEFINED
The IMSI is not defined.
FAULT CODE 73 SUBSCRIBER DISCONNECTION IN PROGRESS
Disconnection in progress for that mobile subscriber.
FAULT CODE 75 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
The functionality connected to the command is not supported by this exchange.
FAULT CODE 232 TRACE DATA NOT INITIATED FOR THIS IMSI
No trace data are initiated for the specified IMSI.
4.3 Answer Printouts
HLR SUBSCRIBER TRACING DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
7 Command Receiving Block
HSTRA
8 Glossary
HLR Home Location Register
IMSI International Mobile Subscriber Identity
IO Input/Output
9 References
9.1 Printout Descriptions
HLR SUBSCRIBER TRACING DATA
9.2 Application Information
HTRAN
COMMAND DESCRIPTION 2/190 82-CNT 238 0034 Uen D
HGSDP
© Telefonaktiebolaget LM Ericsson 2001
Home Location Register, Subscriber Data, Print
1 Format
1.1 Command
/ \
/ \ | / \ |
|MSISDN=msisdn...| | |ALL | |
| | | |SUDA| |
HGSDP:+IMSI=imsi... + |,+SSDA+ |;
| | | |LOC | |
|CONNECTED | | |PDP | |
\ / | \ / |
\ /
1.2 Parameters
ALL All subscriber data
CONNECTED All connected subscribers
IMSI=imsi International Mobile Subscriber Identity (IMSI)
See the Application Information for block HTRAN.
LOC Subscriber location data
MSISDN=msisdn Mobile Station ISDN Number (MSISDN)
See the Application Information for block HTRAN.
PDP Packet Data Protocol (PDP) context subscriber data
Application system dependant parameter.
SSDA Permanent and supplementary service subscriber data
SUDA Permanent subscriber data
2 Function
This command prints subscriber data for mobile subscribers in Home Location Register
(HLR).
Answer printout HLR SUBSCRIBER DATA is received.
Associated answer printouts are also received depending on the parameter given:
PERMANENT SUBSCRIBER DATA, SUPPLEMENTARY SERVICE DATA, LOCATION DATA
and PACKET DATA PROTOCOL CONTEXT DATA answer printouts are received when
parameter ALL is entered.
PERMANENT SUBSCRIBER DATA is received when parameter SUDA is entered.
PERMANENT SUBSCRIBER DATA and SUPPLEMENTARY SERVICE DATA answer
printouts are received when parameter SSDA is entered.
LOCATION DATA answer printout is received when parameter LOC is entered.
PACKET DATA PROTOCOL CONTEXT DATA answer printout is received when parameter PDP is entered.
This command can be initiated from up to 16 Input/Output (IO) devices simultaneously.
The order does not remain after system restart.
3 Examples
3.1 Example 1
HGSDP:CONNECTED;
Subscriber data for all connected subscribers are printed.
3.2 Example 2
HGSDP:IMSI=1234567890,ALL;
All subscriber data for the mobile subscriber with IMSI 1234567890 are printed.
3.3 Example 3
HGSDP:IMSI=1234567890,SUDA;
Permanent subscriber data for the mobile subscriber with IMSI 1234567890 are printed.
3.4 Example 4
HGSDP:MSISDN=3417429013,SSDA;
Permanent and supplementary service subscriber data for the mobile subscriber with
MSISDN 3417429013 are printed.
3.5 Example 5
HGSDP:MSISDN=3417429013,LOC;
Location data for the mobile subscriber with MSISDN 3417429013 are printed.
3.6 Example 6
HGSDP:CONNECTED,LOC;
Location data for all connected subscribers are printed.
3.7 Example 7
HGSDP:MSISDN=3417429013&3417429015,SSDA;
Permanent and supplementary service subscriber data for the mobile subscribers with
MSISDNs 3417429013 and 3417429015 are printed.
3.8 Example 8
HGSDP:IMSI=3417429013&3417429015,PDP;
PDP context data for the mobile subscribers with IMSIs 3417429013 and 3417429015 are
printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED
fault type
Fault type:
FUNCTION BUSY
The function is busy.
FORMAT ERROR
The command or a parameter was incorrectly specified.
UNREASONABLE VALUE
details
The parameter was specified with an unreasonable value.
FAULT CODE 183 PARAMETER NOT SUPPORTED BY THIS EXCHANGE
details
The parameter is not supported by this exchange.
4.3 Answer Printouts
HLR SUBSCRIBER DATA LOCATION DATA PACKET DATA PROTOCOL CONTEXT DATA PERMANENT SUBSCRIBER DATA SUPPLEMENTARY SERVICE DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
7 Command Receiving Block
HSDA
8 Glossary
HLR Home Location Register
IMSI International Mobile Subscriber Identity
IO Input/Output
MSISDN Mobile Station ISDN Number
PDP Packet Data Protocol
9 References
9.1 Printout Descriptions
HLR SUBSCRIBER DATA
LOCATION DATA
PACKET DATA PROTOCOL CONTEXT DATA
PERMANENT SUBSCRIBER DATA
SUPPLEMENTARY SERVICE DATA
9.2 Application Information
HTRAN
top related