t: +27 32 552 2676 | f: +27 86 608 2866 | w: macroburn cremators macrotec designs and manufactures...
Post on 22-May-2020
1 Views
Preview:
TRANSCRIPT
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
MacroBurn Cremators
Macrotec designs and manufactures high quality Cremators based on our thermal technology developed over several decades. Our Cremators are designed for maximum reliability and minimum emissions. They are designed to control the rate of combustion and minimise emissions in a four chamber process.
Our Cremators can be optionally fitted with a Ceramic Filtration Plant to further reduce emissions. As such, our Cremators comply with South African and International standards.
Our Cremators
MacroBurn Cremators are designed utilising the high standard of technology we have created through many years of building high quality, economical and reliable Cremators. Our Cremators are designed taking into account the special requirements that crematoriums create, and have been designed to reduce emissions to extremely low levels.
MacroBurn Cremators utilize a three chamber process, with the coffin being placed in the Primary Chamber where highly combustible components are burnt away. Gasses pass through a Secondary Chamber, with a high degree of turbulence for ideal mixing, completing the burnout and eliminating entrained smoke and other combustible particles. A long residency time of over 2 seconds in the secondary chamber ensures complete combustion. A third chamber is located beneath the primary chamber, where all liquid waste is burned away.
Our Cremators are designed with automatic control of air and combustion rate, which will prevent excessive burning and conversely increase combustion when the burning rate is too low, with temperatures regulated between 850°C and 1000°C. For maximum automation, our PLC system can be installed to fully automate all functionality, and allow for remote monitoring and alarms of all parameters. MacroBurn Cremators are manufactured to the highest quality, and as such use a high quality Alumina-Silicate refractory, with a very high strength, service temperature of up to 1,500°C, high abrasion and chemical resistance, and an expected lifetime of over 15 years. The efficiency of our Cremators is further increased by using pre-heated air, reducing fuel usage. With these efficiencies, our Cremators are able to complete a cremation in just over an hour when running continuously.
Environmental Impact
Macrotec has engineered our Cremators to combat every possible threat it could pose to the environment. We make use of advanced designs in our combustion plant, which completely regulates the combustion rate, temperature in the different chambers, turbulence, gas velocities and supply of oxygen. This prevents formation and eliminates all carbonaceous matter, entrained ash, and chemically formed compounds.
Our Cremators can also be optionally fitted with an advanced Ceramic Filtration Plant that further reduces emissions. The filtration plants make use of high temperature ceramic filter elements that are able to withstand temperatures of up to 1,200°C with high resistance to attack by acids and alkalis.
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
EMISSION POST FILTER TYPICAL EMISSION LIMITParticle Matter < 10 < 40CO < 50 < 75NOx < 300 < 500Hg < 0.05 < 0.05
*All measurements are in mg/Nm³
V221Cremator DimensionsLength 2895Width 2570Height 2545Loading Door 750 x 750
Chimney DimensionsDiameter 561Standard Height 1495Max Height (No Guys) 16000
Capacity DataBurn Rate Continuous (kg/h) 132Burn Rate Intermittent (kg/h) 60 - 80Grate Hearth Area (m²) 2.27Primary Volume (m³) 2.38Incinerator Weight (kg) 11800Chimney Weight (kg) 760
*All measurements are in mm, unless indicated otherwise.
Typical Emissions
Model Range
MacroBurn Cremators are available in one standard size, though Macrotec can custom build designs according to customer specifications.
Further Specifications:
• Gas or Diesel fired burners available.• Electrical panels are dust and water proof IP65 powder coated enclosures. Electrical circuit breakers are in accordance to SABS IEC 60947-2. Should you require a certain specification or brand of electrical components, please advise us during the quotation stage as we use components as per supplier availability.
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
LOA
DIN
G D
OO
R
CH
IMN
EY S
TAC
K
PRIM
AR
Y C
HA
MB
ER
REF
RA
CTO
RY
SUPP
OR
T B
ASE
2545
CH
IMN
EY S
TAC
K
REF
RA
CTO
RY
SUPP
ORT
BA
SE
LOA
DIN
G D
OO
R
PRIM
ARY
CH
AM
BER
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
2420
2916
SEC
ON
DA
RY
BU
RN
ER
PRIM
AR
Y B
UR
NER
PRIM
AR
Y C
HA
MB
ER
PHA
SE 2
BU
RN
ER
ELEC
TRIC
AL
PAN
EL
LOA
DIN
G D
OO
R
REF
RA
CTO
RY
SLA
BS
SEC
ON
DA
RY
CH
AM
BER
CH
IMN
EY S
TAC
K
SEC
ON
DA
RY B
UR
NER
SEC
ON
DA
RY C
HA
MBE
R
CH
IMN
EY S
TAC
K
REF
RA
CTO
RY S
LABS
PHA
SE 2
BU
RN
ER
ELEC
TR
ICA
L PA
NEL
LOA
DIN
G D
OO
R
PRIM
ARY
BU
RN
ERPR
IMA
RY C
HA
MBE
R
T: +27 32 552 2676 | F: +27 86 608 2866 | W: www.macrotec.co.za
Tel: +27 32 552 2676Website: www.macrotec.co.za Email: info@macrotec.co.za
top related