• floor mounted jib cranes • portable jib ... · pdf file• floor mounted jib...
Post on 01-Feb-2018
393 Views
Preview:
TRANSCRIPT
1377 Kimberly Dr., Neenah, WI 54956 (920)-722-0101 FAX (920)-722-5260
www.contrx.com
FESTOON SYSTEMS, CRANE RAILS, CRANE CONTROLS,CRANE REPAIR & REBUILDING, MACHINING SERVICE6-23-2016
• FLOOR MOUNTED JIB CRANES• PORTABLE JIB CRANES• WORKSTATION JIB CRANES• WALL MOUNTED JIB CRANES• GANTRY CRANES• FORKLIFT JIBS• BELOW THE HOOK EQUIPMENT• BRIDGE CRANES
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
Optional top entry electrical collectorcan be attached to most 360° revolvingjib cranes. No special parts needed.
Sleeve mount base(Optional)
Optional factory installedbottom entry electrical
collector brings power inthrough the column assembly.
Optional motorizedboom rotation
Foundation mount base(Optional)
Bolt-type base plate(Standard)
10-22-02
BeamAssembly
ColumnAssembly
HeadAssembly
SELF-SUPPORTING FLOOR CRANESNEED MINIMUM HEAD ROOM.
HEAVY DUTY JIB CRANES- 360° ROTATION -
"A" SERIES
FLOOR MOUNTED
Contrx "A"- jibs are ruggedly constructed for industrialuse and years of trouble-free service. Complete boomassembly is supported by an adjustable column rollerassembly to permit field adjustment and insure evenpressure of rollers on pipe. The boom is constructed
using an I shaped rolled steel beam. The headassembly has two heavy side plates with reinforcing
steel to create a rigid pivoting connection between thebeam assembly and the column assembly. Standardjibs up to 20' span and 20' height under boom. Contrx
specializes in modifications and custom designs.
1377 Kimberly DriveNeenah, WI 54956-1642
Office (920) 722-0101Fax (920) 725-1394
TrolleyEnd Stops
EndstopMountingHardware
Boom Assembly
Lower RollerAssembly
Anchor BoltHardware
Boom Mounting Hardware(see Note 2)
Head Assembly
Main Bearing(see Note 1)
Upper Bearing Pin
Column Assembly
Column Gussets
Jib Base Plate
Boom LevelingAdjustment Nuts (8)
LowerRoller (2)
Thrust Washer (4)The following models have (2):-4000# cap. with longer than 16'-0" boom--6000# cap. with longer than 10'-0" boom--10,000# cap. all boom lengths-
Lock Pin (2)
Roller Shaft (2)
Concrete Footing and'L' Anchor Bolts(by customer) Refer to:FLOOR MOUNT 'A' JIB drawing number
________________
Main Bearing Cup(pressed in at factory)
Boom MountingHardware
Beam Plate
Trolley Stops(field drill boom)
www.contrx.comBoom Length
DWG NO
'A' Jib Assembly Detail
A-1005-A8-16-02 Not to scale
Note 1:Complete bearing assembly factory installedin the Boom Assembly on the following models:-4000# cap. with longer than 16'-0" boom--6000# cap. with longer than 10'-0" boom--all 10,000# cap. A-jibs-
Note 2:Beveled washers are to be used on taperedflange beams only.
Note 3: For orders with similar multiple cranes,look for markings on the inside of the beamplate and the matching face of the headassembly. This will insure the correct partsare matched up.
16"16"
16"16"16"
16"16"
23-3/4"23-3/4"
16"16"
23-3/4"
23-7/8"23-7/8"
21-1/8"23-7/8"
23-7/8"23-7/8"
24-1/2"
4'4'
4'4'4'
4'4'
4'4'
4'4'
4'
4'4'
4'4'
4'4'
4'
7'7'
7'7'8'
7'7'
8'8'
7'7'
8'
9'9'
9'9'
10'10'
10'
17-3/8"17-3/8"
17-3/8"17-3/8"17-3/8"
17-3/8"17-3/8"
21-3/8" **21-3/8"
17-3/8"21-3/8"
21-1/2"
24-1/2"21-1/2"
24-1/2"24-1/2"
29-1/2"24-1/2"
29-1/2"
42"42"
42"48"48"
42"42"
48"48"
42"48"
48"
54"54"
66"66"
72"66"
72"
38"38"
38"44"44"
38"38"
44"44"
38"44"
44"
50"50"
60"60"
66"60"
66"
22002120
196023422422
19802057
34393315
19162716
3759
49804434
46274983
60865135
6843
A21020A21018
A31014A31016A31018
A41012A41014
A41020A41018
A61010A61012
A61016
A61020A61018
A101012A101014
A101018A101016
A101020
24222229
206924672547
21062182
35803456
20412857
3968
52314642
48785234
64015386
7158
A21220A21218
A31214A31216A31218
A41212A41214
A41220A41218
A61210A61212
A61216
A61220A61218
A101212A101214
A101218A101216
A101220
25472467
230725932742
22312307
43373597
21662998
4176
54824850
55785933
67166085
7473
A21420A21418
A31414A31416A31418
A41412A41414
A41420**A41418
A61410A61412
A61416
A61420A61418
A101412A101414
A101418A101416
A101420
10'
12'
12'
12'
14'
14'
14'
16'
16'
16'
18'
18'
18'
18'
18'
20'
20'
20'
20'
2,0002,000
3,0003,0003,000
4,0004,000
4,0004,000
6,0006,000
6,000
6,0006,000
10,00010,000
10,00010,000
10,000
W12W12
W12W12W12
W12W12
W12W12
W12W12
W12
W12W12
W12W12
W12W12
W12
7"7"
7"7"7"
7"7"
7"7"
7"7"
7"
9"9"
8-1/4"9"
9"9"
9"
1-1-11
8'
21"
21"
21"
21-1/8"21-1/8"
4'
4'
4'
4'4'
8'
8'
8'
9'9'
17-3/8"
17-3/8"
21-3/8"
21-1/2"21-1/2"
48"
48"
48"
60"60"
44"
44"
44"
56"56"
2877
2649
3075
38263962
A31020
A41016
A61014
A10108A101010
3002
2774
3216
40344170
A31220
A41216
A61214
A10128A101210
3197
2969
3357
44954631
A31420
A41416
A61414
A10148A10141010'
14'
16'
20'3,000
4,000
6,000
10,00010,000
W12
W12
W12
W12W12
6-1/2"
6-1/2"
6-1/2"
8-1/4"8-1/4"
8'
12-3/8"12-3/8"
12-3/8"
12-3/8"
16"
12-3/8"
4'4'
4'
4'
4'
3'
6'7'
6'
6'
7'
5'
12-3/8"12-3/8"
12-3/8"
12-3/8"
17-3/8"
17-3/8"
36"36"
42"
36"
42"
36"
32"32"
38"
32"
38"
32"
15021615
1588
1435
1836
1888
A21014A21016
A31012
A41010
A6108
A11020
16651725
1697
1545
1961
1997
A21214A21216
A31212
A41210
A6128
A11220
17741834
1806
1654
2086
2106
A21414A21416
A31412
A41410
A6148
A11420
10'
12'
14'16'
20'
2,0002,000
3,000
4,000
6,000
1,000
W12W12
W12
W12
W12
W12
6-1/2"6-1/2"
6-1/2"
6-1/2"
7"
6-1/2"
8'
8'
10-3/8"10-3/8"
10-3/8"
10-3/8"
10-3/8"
10-3/8"
3'3'
4'
4'
4'
4'
5'5'
6'
6'
6'
6'
12-3/8"12-3/8"
12-3/8"
12-3/8"
12-3/8"
12-3/8"
36"36"
36"
36"
36"
36"
32"32"
32"
32"
32"
32"
14921543
1388
1335
1337
1283
A11016A11018
A21012
A31010
A4108
A3108
15911642
1487
1434
1446
1382
A11216A11218
A21212
A31210
A4128
A3128
16901815
1586
1607
1555
1482
A11416A11418
A21412
A31410
A4148
A314810'
12'
16'18'1,000
1,000
2,000
3,000
4,000
3,000
W12W12
W12
W12
W12
W12
5-3/4"5-3/4"
5-3/4"
5-3/4"
5-3/4"
5-3/4"
"S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam. * Model A21410 has an 'F' dimension of 12-1/4".** Model A41420 has an 'F' dimension of 21-1/2"
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394
FLOOR MOUNTED 'A' SERIESJIB CRANE SPECIFICATIONS
www.contrx.com
8'
8'D
8"8"8"
8"8"
3'3'3'
4'4'
3'E
4'4'5'
5'5'
4'W
10-1/4"F
10-1/4"10-1/4"12-1/4"
10-1/4" *10-1/4"
24"24"
24"BD
36"36"
36"
20"20"
20"BC
32"32"
32"
670LBS. LBS.LBS.
822858
1081
950913
MODEL MODELMODELA1108A11010A11012A11014
A21010A2108
715878914
1137
1006969
A1128A11210A11212A11214
A21210A2128
760934970
1499
14261025
A1148A11410A11412A11414
A21410*A2148
A
10'
10'12'14'
6"
B = 12' HT. B = 14' HT.B = 10' HT.
1,0001,0001,0001,000
2,0002,000
BEAMTYPE
BOLTHOLES
S6S6S12
S12S12
S6
CAP.(LBS.) FW
4"4"
4"4"
4"3-3/8"
DIMENSIONS
W
B
BOOM ASSEMBLYFIELD MOUNT
D
2"
HEADASSEMBLY
COLUMNASSEMBLY
FW
LOWERROLLERASSEMBLY
3/4" DIA. REINFORCING RODS6" FROM TOP & BOTTOMAPPROX. 12" ON CENTERBOTH WAYS
BOLT CIRCLEDIAMETER
(BC)
BASE PLATEDIAMETER
(BD)
F A
WW
1-1/4" DIA.6 PLACES
1-1/4" DIA.12 PLACES
60° 30°
BASE DETAILHOLES EQUALLY SPACED
E
Jib Crane Accessories:- Anchor Bolt Kits- Tagline Kits- Templates (Paper & Plywood)- Hoists & Trolleys (Electric & Manual)- Motorized Rotation
4"
BASE
3/4 E
CAP. (LBS)
DIMENSIONS BOLT HOLES
BEAM TYPE
B=16’ B=18’ B=20’
A D FW E W F BD BC LBS. MODEL LBS. MODEL LBS. MODEL 1,000 8’ 6” 3-3/8” 3’ 4’ 10-1/4” 24” 20” 6 S 804 A1168 849 A1188 894 A1208 1,000 10’ 8” 4” 3’ 4’ 12-1/4” 36” 32” 12 S 1525 A11610 1624 A11810 1723 A12010
1,000 12’ 8” 4”
3’ 4’ 12-1/4”
36” 32” 12 S 1562 A11612 1661 A11812
10-3/8” 5-3/4” 12-3/8” W 1987 A12012
1,000 14’ 8” 4”
3’ 5’ 12-1/4”
36” 32” 12 S 1598 A11614
10-3/8” 5-3/4” 12-3/8” W 1930 A11814 2039 A12014 1,000 16’ 10-3/8” 5-3/4” 3’ 5’ 12-3/8” 36” 32” 12 W 1872 A11616 1979 A11816 2091 A12016
1,000 18’ 10-3/8” 5-3/4”
3’ 5’ 12-3/8” 36” 32”
12 W 1924 A11618
12-3/8” 6-1/2” 17-3/8” 42” 38” 2518 11818 2643 A12018 1,000 20’ 12-3/8” 6-1/2” 3’ 5’ 17-3/8” 42” 38” 12 W 2453 A11620 2578 A11820 2703 A12020
2,000 8’ 8” 4” 4’ 5’ 12-1/4” 36” 32” 12 S 1488 A2168 1587 A2188 1686 A2208
2,000 10’ 8” 4”
4’ 5’ 12-1/4”
36” 32” 12 S 1525 A21610
10-3/8” 5-3/4” 12-3/8” W 1825 A21810 1934 A22010
2,000 12’ 10-3/8” 5-3/4”
4’ 6’ 12-3/8” 36” 32”
12 W 1769 A21612
12-3/8” 6-1/2” 17-3/8” 42” 38” 2338 A21812 2463 A22012
2,000 14’ 12-3/8” 6-1/2”
4’ 6’ 17-3/8” 42” 38”
12 W 2273 A21614 2398 A21814
16” 7” 48” 44” 3006 A22014
2,000 16’ 16” 7” 4’ 7’ 17-3/8” 42” 38”
12 W 2513 A21616
48” 44” 2945 A21816 3086 A22016
2,000 18’ 16” 7”
4’ 7’ 17-3/8”
48” 44” 12 W 2884 A21618 3025 A21818
21” 6-1/2” 21-1/2” 4732 A22018
2,000 20’ 16” 7”
4’ 7’ 17-3/8”
48” 44” 12 W 2964 A21620 3105 A21820
21” 6-1/2” 21-1/2” 4846 A22020
3,000 8’ 10-3/8” 5-3/4” 4’ 6’ 12-3/8” 36” 32” 12 W 1581 A3168 1680 A3188 1779 A3208
3,000 10’ 10-3/8” 5-3/4”
4’ 6’ 12-3/8” 36” 32”
12 W 1716 A31610 1825 A31810
12-3/8” 6-1/2” 17-3/8” 42” 38” 2403 A32010
3,000 12’ 12-3/8” 6-1/2”
4’ 6’ 17-3/8” 42” 38”
12 W 2213 A31612
16” 7” 48” 44” 2788 A31812 2929 A32012 3,000 14’ 16” 7” 4’ 7’ 17-3/8” 48” 44” 12 W 2724 A31614 2865 A31814 3006 A32014
3,000 16’ 16” 7”
4’ 7’ 17-3/8”
48” 44” 12 W 2804 A31616 2945 A31816
21” 6-1/2” 21-1/2” 4618 A32016
3,000 18’ 16” 7”
4’ 8’ 17-3/8”
48” 44” 12 W 2884 A31618 3025 31818
21” 6-1/2” 21-1/2” 4732 A32018 3,000 20’ 21” 6-1/2” 4’ 8’ 21-1/2” 48” 44” 12 W 4430 A31620 4638 A31820 5305 A32020
4,000 8’ 10-3/8” 5-3/4” 4’ 6’ 12-3/8” 36” 32” 12 W 1664 A4168 1773 A4188 1882 A4208
4,000 10’ 12-3/8” 6-1/2” 4’ 6’ 12-3/8” 36” 32” 12 W 1763 A41610 17-3/8” 42” 38” 12 W 2278 A41810 2403 A42010
4,000 12’ 16” 7” 4’ 7’ 17-3/8” 42” 38”
12 W 2354 A41612
21-3/8” 48” 44” 3255 A41812 3396 A42012 4,000 14’ 16” 7” 4’ 7’ 21-3/8” 48” 44” 12 W 3194 A41614 3335 A41814 3476 A42014
4,000 16’ 23-3/4” 7” 4’ 8’ 21-3/8”
48” 44” 12 W 3614 A41616
21-1/2” 4505 A41816 4778 A42016
4,000 18’ 23-3/4” 7” 4’ 8’ 21-3/8”
48” 44” 12 W 3738 A41618
21-1/2” 4629 A41818 4902 A42018
4,000 20’ 23-3/4” 7” 4’ 8’ 21-1/2” 48” 44”
12 W 4545 A41620
24-1/2” 54” 50” 5643 A41820 5894 A42020
6,000 8’ 16” 7” 4’ 7’ 17-3/8” 42” 38” 12 W 2212 A6168 2337 A6188 2462 A6208 6,000 10’ 16” 7” 4’ 7’ 17-3/8” 42” 38” 12 W 2292 A61610 2417 A61810 2542 A62010
6,000 12’ 16” 7”
4’ 7’ 21-3/8” 48” 44”
12 W 3139 A61612 3281 A61812
21” 6-1/2” 8’ 21-1/2” 54” 50” 4747 A62012
6,000 14’ 21” 6-1/2” 4’ 8’ 21-3/8” 48” 44”
12 W 3498 A61614
21-1/2” 54” 50” 4653 A61814 4861 A62014
6,000 16’ 23-3/4” 7”
4’ 8’ 21-1/2” 48” 44”
12 W 4384 A61616
23-7/8” 9” 24-1/2” 54” 50” 5680 A61816 5931 A62016 6,000 18’ 23-7/8” 9” 4’ 9’ 24-1/2” 54” 50” 12 W 5581 A61618 5832 A61818 6083 A62018 6,000 20’ 23-7/8” 9” 4’ 9’ 24-1/2” 54” 50” 12 W 5733 A61620 5984 A61820 6235 A62020
10,000 8’ 21-1/8” 8-1/4” 4’ 9’ 21-3/8” 60” 56” 12 W 4746 A10168 4997 A10188 5248 A10208 10,000 10’ 21-1/8” 8-1/4” 4’ 9’ 21-1/2” 60” 56” 12 W 4882 A101610 5133 A101810 5384 A102010 10,000 12’ 21-1/8” 8-1/4” 4’ 9’ 24-1/2” 66” 60” 12 W 5892 A101612 6207 A101812 6522 A102012 10,000 14’ 23-7/8” 9” 4’ 9’ 24-1/2” 66” 60” 12 W 6248 A101614 6563 A101814 6878 A102014 10,000 16’ 23-7/8” 9” 4’ 10’ 24-1/2” 66” 60” 12 W 6400 A101616 6715 A101816 7030 A102016 10,000 18’ 23-7/8” 9” 4’ 10’ 29-1/2” 72” 66” 12 W 7031 A101618 7346 A101818 7661 A102018 10,000 20’ 24-1/2” 9” 4’ 10’ 29-1/2” 72” 66” 12 W 7788 A101620 8103 A101820 8418 A102020
FLOOR MOUNTED ‘A’ SERIES JIB CRANE SPECIFICATIONS
6/20/2016
SALES-A-6H12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
BOOM ASSEMBLYTROLLEY STOPS
(FACTORY MOUNTED)
4"
CONCRETE FOOTING
FLOOR
BASE DIAMETER
30°
BASE DETAIL
6 HOLES1-1/4" DIA.
BOLT CIRCLEDIAMETER
REINFORCING RODS3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.
TROLLEY STOPS(FIELD MOUNTED)
1" ANCHOR BOLTS REQ'D.
ROLLERASSEMBLY
HEADASSEMBLY
COLUMNASSEMBLY
BC
FW
W
E
BC
BD
W
3/4 E
F A
D
CAPACITY
WEIGHT
A
B
C
D
E
F
NOTES
BC
W
BD
FW
LBS.
LBS.
• NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
FLOOR MOUNT 'A' JIBWITH 6-HOLE BASE
SALES-A-12H12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
BOOM ASSEMBLYTROLLEY STOPS
(FACTORY MOUNTED)
4"
CONCRETE FOOTING
FLOOR
BASE DIAMETER
BASE DETAIL
BOLT CIRCLEDIAMETER
REINFORCING RODS3/4" DIA. TOP AND BOTTOM ON
APPROX. 12" CENTERS BOTH WAYS.
TROLLEY STOPS(FIELD MOUNTED)
1" ANCHOR BOLTS REQ'D.
ROLLERASSEMBLY
HEADASSEMBLY
COLUMNASSEMBLY
B
C
FW
W
E
BC
BD
W
3/4 E
F A
D
CAPACITY
WEIGHT
A
B
C
D
E
F
NOTES
BC
W
BD
FW
LBS.
LBS.
30°
12 HOLES1-1/4" DIA.
• NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
FLOOR MOUNT 'A' JIBWITH 12-HOLE BASE
F A
B
C
D
FW
W
E
7/8" DIA.HOLE (4)
S
BW
SALES-A-FM12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
4' 0"
BOOM ASSEMBLY
CONCRETE FOOTING
FLOOR
REINFORCING RODS
3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.
TROLLEY STOPS(FACTORY MOUNTED)
TROLLEY STOPS(FIELD MOUNTED)
ROLLERASSEMBLY
HEADASSEMBLY
COLUMNASSEMBLY
12"
BASEPLATE
SQUARE BASE PLATE DETAIL
CAPACITY
WEIGHT
A
B
C
D
E
F
S
W
BW
FW
LBS.
LBS.
NOTES • NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
FOUNDATION MOUNT 'A' JIB
F A
BC
D
FW
W
E
W
E
7/8" DIA.HOLE (4)
X
SBW
SALES-A-SM12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
4' 0"
BOOM ASSEMBLY
CONCRETE FOOTING
FLOOR
REINFORCING RODS3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.
TROLLEY STOPS(FACTORY MOUNTED)
TROLLEY STOPS(FIELD MOUNTED)
ROLLERASSEMBLY
HEADASSEMBLY
COLUMNASSEMBLY
12"
BASEPLATE
SLEEVE(INCLUDED)
4' 0"CONCRETE FOOTING
FLOOR
12"
SLEEVEBASE
PLATE
SLEEVE BASE PLATE DETAIL
SLEEVE
INSTALLATION INSTRUCTIONS
1. PREPARE FIRST POUR FOOTING WITH ANCHOR BOLTS SET AS SHOWN.
2. AFTER FOOTING HARDENS, INSTALL AND LEVEL SLEEVE.SECURE BASE TO PREVENT SHIFTING DURING SECOND POUR.
3. POSITION REBAR PATTERN APPROX. 6" FROM TOPAND BOTTOM OF SECOND POUR.
4. MAKE SECOND POUR FOUNDATION, TAKING CARE TO MAINTAINSLEEVE IN A PLUMB POSITION. ALLOW CONCRETE TO HARDEN.
5. INSERT JIB COLUMN INTO SLEEVE AND MAKE SURE CENTERING PINPASSES THROUGH HOLE IN CAP PLATE ON BOTTOM OF COLUMN.
6. PLUMB JIB COLUMN. BLOCKS OR WEDGES (NOT PROVIDED) MAY BEINSERTED BETWEEN SLEEVE AND COLUMN TO HELP MAINTAIN POSITION.
7. INSTALL JIB HEAD & BOOM SECTION ON COLUMN. ROTATE BOOM
8. WHEN POSITION OF COLUMN IS SATISFACTORY, INSTALL SPLITCOLLAR WITH FILLET WELDS TO BOTH COLUMN AND SLEEVE LIPALL THE WAY AROUND.
JIB COLUMN
SPLIT COLLAR
CENTERING PIN
WELD
FIRST POUR
SECONDPOUR
WEDGE
3/4" 'L' ANCHORS (4)
SLOWLY TO CHECK COLUMN PLUMBNESS. ADJUST BLOCKINGAS REQUIRED.
CAPACITY
WEIGHT
A
B
C
D
E
F
COLUMN OD
W
SBW
X
SLEEVE ID
FW
LBS.
LBS.
NOTES • NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
SLEEVE MOUNT 'A' JIB
F A
BC
W
E
W
3/4E
D
FW
SALES-A-MD-12H12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
TIGHT WIRE ASSY BOOM ASSEMBLY
CONCRETE FOOTING
FLOOR
30°
BASE DETAIL
12 HOLES1-1/4" DIA.
BASE PLATEDIAMETERBD
BOLT CIRCLEDIAMETERBC
REINFORCING RODS3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.
TROLLEY STOPS(FIELD MOUNTED)
1" ANCHOR BOLTS REQ'D.
ROLLERASSEMBLY
HEADASSEMBLY
COLUMNASSEMBLY
SPROCKET
CONTROLPANEL
ACCESSHOLE
BRAKEMOTOR
GEARREDUCER
4C/SO CORD (POWER)6C/SO CORD (CONTROL)
4 RING BOTTOM ENTRYELECTRICAL COLLECTOR
4" DIA HOLE FORPOWER SUPPLY
4"
BASEPLATE
POWER IN
CAPACITY
WEIGHT
A
B
C
D
E
F
1/2 RPM115-1-60V
JIB ROTATION SPEED:CONTROL VOLTAGE:
NOTES BC
W
BD
SUPPLY VOLTAGE
FW
LBS.
LBS.
• NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
MOTORIZED FLOOR MOUNT 'A' JIBWITH 12-HOLE BASE
CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 722 5260 or (920) 725 1394 Fax
www.contrxcranes.com
INSTALLATION INSTRUCTIONS FLOOR MOUNT JIB CRANE
****PLEASE READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY****
1. The jib crane is shipped in three sections: head assembly, mast assembly, and boom assembly. A box containing the top bearing and mounting hardware is also included. For identical jibs ordered in multiple quantities, look for markings on the head assemblies and beam assemblies. Match each head assembly with the correct beam assembly.
2. The footing shown is the only method recommended by the manufacturer. An individual competent
in related foundation design methods and familiar with the installation site should design any alternative method.
3. Use a minimum 3000 PSI (5 bag) mix for concrete. A 2500 PSF soil pressure is assumed. Prior to
pouring, position the rebar and ‘L’ shaped anchor bolts as shown. Anchor bolts are submerged ¾ of footing depth. The anchor bolt material specification is A36. Rebar is located 6 inches from top and bottom of the footing. Be sure to allow for power conduit if feeding through the base of the jib. Position the anchor bolts according to the base plate bolt circle dimensions. (The anchor bolts can be purchased through your jib crane supplier.)
4. After the concrete hardens, make sure a flat, level surface exists for accepting the mast assembly.
Machinery grout and jam nuts may be used to level the surface. Erect the mast on the prepared surface, taking care not to damage the anchor bolt threads while setting the base plate in position. Tighten double nuts onto the anchor bolts after insuring that the mast is plumb.
5. Mount the top pivot bearing cone over the pin on top of the mast assembly. If installing the bottom
entry collector option, read the collector installation instructions at this time. Attach boom assembly to head assembly with the hardware provided. Set the boom and head assembly in place on the mast. Make sure the roller bearing on top of the mast is seated correctly into the bearing race on the boom assembly.
6. Adjust the lower roller assembly in the head section to bring the boom into horizontal.*
7. Grease upper bearing and 5” diameter lower rollers through zerk fitting provided. Re-lube as
conditions require. The 3” diameter lower rollers are self-lubricating. **
8. Rotate the boom assembly to check for free movement and proper bearing seating.
9. Install the trolley end stops on the boom. Attach other optional equipment according to directions provided with the equipment.
*Note - Small jibs are not adjustable at the lower rollers and may be leveled by shimming between the boom and the head mounting plates.
**Note - Small jibs are not equipped with a zerk fitting and need to be greased at the top bearing prior to seating the boom and head assembly.
WARNING: THIS EQUIPMENT IS NOT DESIGNED FOR AND SHOULD NOT BE USED FOR LIFTING, SUPPORTING OR TRANSPORTING PEOPLE.
12-11-07
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101Fax (920) 725-1394www.contrx.com Optional top entry electrical collector
can be attached to most 360° revolvingjib cranes. No special parts needed.
1-29-03
Boom Assembly
Upper PipeAssembly
ColumnAssembly
Base Plate
Concrete Foundation(by others)
"L" Anchor Bolts(Sold Separately)
Lower Thrust Roller (2)
Power In
Power to Crane Accessories
MEDIUM DUTY JIB CRANES- 360° ROTATION -
"B" SERIES
FLOOR MOUNTED
Contrx brand "B" series jib cranes are wellengineered and constructed machines ateconomical prices. The upper pipe assemblyis jig welded to assure accuracy. Two heavy dutylower thrust rollers with lubrication-free teflonbearings assure smooth operation as the boomrotates on a tapered roller bearing atop the columnassembly. The steel base plate and the columnpipe are welded together robotically to insure asquare connection.
Standard Features:• Boom rotates 360°• Rolled steel I-beam boom fits most standard hoist trolleys.• Bolt-on trolley end-stops allow easy trolley installation.• Safety yellow enamel primer and paint finish• Mounting details provided with installation instructions• Adjustable rollers on 2000 lb. capacity units allow for boom leveling.
Options:• Anchor bolt kits• Base plate templates (paper or plywood)• Hoists and trolleys• Boom rotation stops• Top entry electrical collectors• Tagline festoon kits• Contact us for special requests.
TrolleyEnd Stops
End StopMountingHardware
Boom Assembly
Boom MountingHardware
Main Bearing Cup(Pressed in at Factory)
Upper PipeAssembly
Main Bearing Cone
Upper Bearing Pin
Jib Column
AnchorBolt Hardware
Column Gussets
Jib Base Plate
Concrete Footing and'L' Anchor Bolts(By Customer) Refer to:FLOOR MOUNT 'B' JIBdrawing number
___________________
Thrust Washer (2)
LowerRoller (2)
Lock Pin (2)
Roller Shaft
1377 Kimberly DriveNeenah, WI 54956-1642
Office (920) 722-0101Fax (920) 725-1394
www.contrx.com
RollerShaft (2)
ThrustWasher (2)
LowerRoller (2)
LevelingScrew (4)
Main Bearing Cup(Pressed in at Factory)
Adjustable Lower Roller AssemblyUsed on the following jibs:
-All 1000# cap. with 16'-0" boom--All 2000# cap. B-jibs-
Boom Length
DWG NO
'B' Jib Assembly Detail
B-1005-B10-4-06 Not to scale
Assembly Note: Center the lower rollers directly below the boom.
1-1-11
FLOOR MOUNTED 'B' SERIES JIB CRANE SPECIFICATIONS
Jib CraneAccessories:
- Anchor Bolt Kits- Tagline Kits- Templates (paper & plywood)- Hoists & Trolleys (electric & manual)
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394www.contrx.com
24R6
26R6 28R8 30R12
15S4
500
750
1000
2000
250
500
750
1000
2000
250
500
750
1000
2000
250
500
750
1000
250
500
750
1000
250500
750
1000
2000
250
8'
8'
8'
8'
8'
10'
10'
10'
10'
10'
12'
12'
12'
12'
12'
14'
14'
14'
14'
16'
16'
16'
16'6'
6'
6'
6'
6'
5"
6"
6"
8"
5"
5"
6"
8"
8"
5"
6"
6"
8"
10-3/8"
5"
8"
8"
8"
6"
8"
8"
10-3/8"
6"5"
5"
6"
8"
5"
3"
3 3/8"
3 3/8"
4"
3"
3"
3 3/8"
4"
4"
3"
3 3/8"
3 3/8"
4"
5-3/4"
3"
4"
4"
4"
3 3/8"
4"
4"
5-3/4"
3 3/8"3"
3"
3 3/8"
4"
3"
4'
4'
4'
5'
4'
4'
4'
4'
5'
4'
4'
4'
4'
6'
4'
5'
5'
5'
5'
5'
5'
5'
5'4'
4'
4'
5'
4'
3'
3'
3'
4'
3'
3'
3'
3'
4'
3'
3'
3'
3'
4'
3'
3'
3'
3'
3'
3'
3'
3'
3'3'
3'
3'
4'
3'
5"
6 1/2"
6 1/2"
8 1/2"
4"
5"
6 1/2"
7 1/2"
8 1/2"
4"
6 1/2"
7 1/2"
7 1/2"
9 1/2"
4"
6 1/2"
7 1/2"
7 1/2"
4"
6 1/2"
7 1/2"
8 1/2"
5"5"
6 1/2"
6 1/2"
8 1/2"
4"
15S4
24R6
26R6
28R8
15S4
15S4
24R6
26R6
28R8
15S4
24R6
24R6
26R6
30R12
15S4
24R6
24R6
26R6
15S4
24R6
26R6
26R6
15S415S4
24R6
26R6
28R8**
15S4
378
504
515
802
329
398
529
756
739
349
554
707
793
1091
369
665
818
848
425
702
866
1070
499358
463
490
745
309
B5108
B75108
B1108
B2108
B25108
B51010
B751010
B11010
B21010
B251010
B51012
B751012
B11012
B21012
B251012
B51014
B751014
B11014
B251014
B51016
B751016
B11016
B251016B5106
B75106
B1106
B2106
B25106
B5128
B75128
B1128
B2128
B25128
B51210
B751210
B11210
B21210
B251210
B51212
B751212
B11212
B21212
B251212
B51214
B751214
B11214
B251214
B51216
B751216
B11216
B251216B5126
B75126
B1126
B2126
B25126
B588
B7588
B188
B288
B2588
B5810
B75810
B1810
B2810
B25810
B5812
B75812
B1812
B2812
B25812
B5814
B75814
B1814
B25814
B5816
B75816
B1816
B25816B586
B7586
B186
B286 **
B2586
416
549
560
869
358
436
574
812
905
378
599
763
849
1165
398
710
874
904
454
747
922
1137
537396
508
535
832
338
454
594
605
935
388
474
619
868
972
408
644
819
905
1238
428
755
931
960
484
792
978
1204
575434
553
580
899
368
CAP.(LBS.)
DIMENSIONSA D FW E W F
BASE PLATEMODEL LBS. MODEL LBS. MODEL LBS. MODEL
B = 10' HT. B = 12' HT.B = 8' HT.
BASE PLATEMODEL
BASEDIA.
BOLTCIRCLE
NO.HOLES
HOLEDIA.
BOLTDIA.
24R626R628R8
30R12
15S424"26"28"30"
20"22"24"26"
668
12
41 1/4"1 1/4"1 1/4"1 1/4"
7/8"1"1"1"1"
3/4"
AF
B
FW
W
E
D
3/4 E
4"
12"15"
15"
12"
"S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam. ** B286 Uses base plate model 26R6.
UPPERPIPE
COLUMNASSEMBLY
BASEPLATE
LOWERROLLERS
REINFORCING RODS5/8" DIA. TOP - 3/4" DIA. BOTTOMAPPROX. 12" ON CENTERBOTH WAYS
BOOMASSEMBLY
S
S
S
S
S
S
S
S
S
S
S
S
S
W
S
S
S
S
S
S
S
W
SS
S
S
S
S
BEAMTYPE
AF
FW
D
B
W
E3/4 E
C
SALES-B12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
24R6 26R6 28R8 30R1215S4
BASE PLATEMODEL
BASEDIA.
BOLTCIRCLE
NO.HOLES
HOLEDIA.
BOLTDIA.
24R626R628R830R12
15S424"26"28"30"
20"22"24"26"
668
12
41 1/4"1 1/4"1 1/4"1 1/4"
7/8"1"1"1"1"
3/4"
12"15"
15"
12"
UPPERPIPE
COLUMNASSY.
BASEPLATE
LOWERROLLERS
REINFORCING RODS5/8" DIA. TOP - 3/4" DIA. BOTTOMAPPROX. 12" ON CENTERBOTH WAYS
BOOMASSEMBLY
CONCRETEFOOTING
4"
B
C
D
E
F
W
FW
CAPACITY
WEIGHT
A
BOLTCIRCLEDIAMETER
BASEDIAMETERNOTES
• NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
FLOOR MOUNT 'B' JIB
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
3-7-14
PORTABLE JIB CRANE
This innovative design eliminates the need for costly sitepreparation. The portable jib crane comes with its ownsteel base. No traditional concrete footing is required.
Eliminate conventional jib location restrictions while gainingtrue portability and versatility.
360° Boom Rotation
• No concrete foundation or floor anchoring required
• Easily moved by fork truck for multiple uses
• Easy to store and transport
• Use not limited to ground floor applications
• Not limited to industrial use
2"
FLOOR
A
B
F
D
FW
E
W
S
A
6'-0"
D
5"
E
4"
F
4"
S
26"
FW
3.00"
(LBS.)
2221
CAPACITY(LBS) WEIGHT
W
48"8'-0" 5" 4" 4" 26" 3.00" 224148"10'-0" 5" 6" 4" 26" 3.00" 342748"12'-0" 5" 7" 4" 26" 3.00" 4098
25048"
14-0" 6" 8" 4" 26" 3.33" 480748"
6'-0" 5" 6" 5" 3.00" 34358'-0" 5" 7" 5" 3.00" 410610'-0" 5" 9" 5" 3.00" 5430
500
12'-0" 6" 6" 6 1/2" 3.33" 5571
6'-0" 6" 4" 6 1/2" 3.33" 38098'-0" 6" 6" 6 1/2" 3.33" 5521
1000
PORTABLE JIB CRANE SPECIFICATIONS
MODEL
PBB2586PBB2588
PBB25810PBB25812PBB25814
PBB586PBB588
PBB5810PBB5812
PBB186PBB188
B = 8'-0"
(LBS.)
2250
WEIGHT
2270345641284836
3473414454685615
38545565
MODEL
PBB25106PBB25108
PBB251010PBB251012PBB251014
PBB5106PBB5108
PBB51010PBB51012
PBB1106PBB1108
B = 10'-0"
(LBS.)
2279
WEIGHT
2299348541574865
3511418255065660
38955610
MODEL
PBB25126PBB25128
PBB251210PBB251212PBB251214
PBB5126PBB5128
PBB51210PBB51212
PBB1126PBB1128
B = 12'-0"DIMENSIONS
Features:• Can be easily moved from place to place• Requires no concrete foundation• Can be used on floors above ground floor• Can be easily stored out of the way
Portable Jib Crane Accessories:• Tagline Kits• Trolleys• Hoists• Rotation Stops• Optional Base sizes
Fork Pockets (extend through the base) FP1 = 3" X 7"FP2 = 3-1/2" X 7-1/2"FP3 = 3-1/2" X 8"
26" 48"26" 48"26" 48"26" 60"
26" 60"26" 60"
Not to be used as aforklift truck attachment
• Lifting Lugs
Base footprint is square
BASE
(WEIGHT IS FOR JIB CRANE ONLY)
5-21-13
1377 Kimberly DriveNeenah, WI 54956-1642
Office (920) 722-0101Fax (920) 725-1394
www.contrx.com
FP2
POCKETSFORK
FP2FP3FP3FP3
FP3FP3FP3FP3
FP1FP3
TrolleyEnd Stops
End StopMountingHardware
Boom Assembly
Boom MountingHardware
Main Bearing Cup(Pressed in at Factory)
Upper PipeAssembly
Main Bearing Cone
Upper Bearing Pin
Jib Column
Anchor BoltBolt Hardware Column Gussets
Jib Base Plate
Thrust Washer (2)
LowerRoller (2)
Lock Pin (2)
Roller Shaft
1377 Kimberly DriveNeenah, WI 54956-1642
Office (920) 722-0101Fax (920) 725-1394
www.contrx.com
DWG NO
Portable Jib Assembly Detail
PBB-1005-A8-29-02 Not to scale
Assembly Note: Center the lower rollers directly below the boom.
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
3-29-16
WORKSTATION JIB CRANE
Use this ergonomically designed jib for repetitivemotion material handling applications. Low friction
track and trolley reduces operator fatigue in pick andplace operations. Special trolley, included with the jib
crane, will accept most small capacity hoist hooks.
360° Boom Rotation
FEATURES:
• Available in 100 lb., 250 lb., and 500 lb. capacity
• Boom reach up to 10 ft.
• High-strength enclosed track protects running surface from dirt for minimal resistance.
• Lifetime lubricated and sealed wheel bearings in trolley
• Easy to control load placement
• Fast installation: 100 lb. and 250 lb. capacity units can be anchored to most existing concrete floors.
• Easy to relocate
OPTIONS:
• Anchor bolt kits
• Festooning trolley kit
• Rotation stops
• Top entry electrical collector
• Mounting template
• Adjustable rubber trolley stops
• Light weight electric chain hoist
Load Trolley Included
TrolleyEnd Stop
End StopMountingHardware
Boom AssemblyBoom Mounting
Hardware
Main Bearing Cup(Pressed in at Factory)
Upper PipeAssembly
Main Bearing Cone
Upper Bearing Pin
Jib Column
AnchorBolt Hardware
Column Gussets
Jib Base Plate(100 lb. models have square base plates)
'L' anchor bolts shown are recommendedfor 500 lb. capacity models.Expansion anchors may be used on100 lb. and 250 lb. capacity models.(Anchors not included)
Thrust Washer (2)
LowerRoller (2)
Lock Pin (2)
Roller Shaft (2)
1377 Kimberly DriveNeenah, WI 54956-1642
Office (920) 722-0101Fax (920) 725-1394
www.contrx.com
Concrete Footing
Trolley (Included)
Shim here to adjust boom level.
DWG NO
Workstation Jib Assembly Detail
WSB-10054-6-16 Not to scale
Assembly Note: Center the lower rollers directly below the boom.
7-10-06
W
E 3/4 E
D
A
10' 0"
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394www.contrx.com
WSB WORKSTATION JIB CRANE SPECIFICATIONS
Jib Crane Accessories:
• Anchor bolt kits• Festooning trolley kit• Templates (paper & plywood)• Top entry electrical collector• Adjustable rubber stops• Rotation stops• Hoists (electric & manual)
BASEPLATE
BOOM ASSEMBLY
UPPERPIPE
COLUMNASSEMBLY
SQUARECONCRETEFOOTING
4"
ANCHORS (BY OTHERS)
FLOOR
35"
35H6 32"23H6 20"
23"15"
12"15S4
Base Plates
Cap.(lbs.)100100100250250250500500500
"A"(ft.)681068106810
"D"(in.)6-3/47-3/48-3/48-3/48-3/49-3/49-3/49-3/411-3/4
"G"(in.)
"E"(in.)
"W"(in.)486060486060486060
666666121212
222222222
BasePlt.
15S415S415S423H623H623H635H635H635H6
Wt.(lbs.)379424479424549604614754834
AnchorDia. (in.)
3/43/43/4111111
MODEL NO.WSB1106WSB1108WSB11010WSB25106WSB25108WSB251010WSB5106WSB5108WSB51010
EXPANSION TYPE ON 100 & 250 LB. JIBS'L' TYPE (SHOWN) ON 500 LB. JIBS
G
TROLLEY(INCLUDED)
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
3-20-14
CONTRX INDUSTRIES, IN
C.
NEENAH, WI 5
4956
920-722-0101
MODEL NO.
SERIAL NO.
FULL-CANTILEVEREDWALL MOUNT JIB CRANE
• 180° rotation
• Ideal for maximum headroom and trolley travel
• Mount at any height on wall or building columns where strength permits and true vertical alignment is possible
• High grade steel components for long life
• Hinges with self-lubricating teflon bearings and hardened pins
• Capacities to 6,000 lbs. - standard lengths to 20'
• Primed and painted safety yellow
Options:• Hoists and trolleys• Boom rotation bumpers• Tagline festoon kits• Contact us for special requests.
WMCC608WMCC610WMCC612
WMCC414
WMCC614
WMCC420
WMCC620
WMCC220
WMCC618
WMCC218
4000 LB.
4000 LB.
6000 LB.6000 LB.
6000 LB.6000 LB.6000 LB.
6000 LB.
2000 LB.2000 LB.
8'10'12'
14'
14'
18'
18'
20'
20'
20'
4'4'6'
5'
6'
7'-6"
6'
7'-6"
9'-6"
6'
16"16"16"
16"
16"
23 3/4" 7" WF
23 3/4"
16"
23 3/4"
16"
7" WF7" WF7" WF
7" WF
7" WF
7" WF
7" WF
7" WF
7" WF
8"
8"8"8"8"
8"8"
8"
8"
8"
18"18"22"
16"
22"
22"
18"
22"
2"2"
2"
2"
3"
2"
3"
3"
2"
2" 146751844814871
14240
17440
18629
16" 8561
14521
16512
16" 9643
679759974
887
1054
1743
1083
1840
2135
1163
11/16"
11/16"
11/16"11/16"
11/16"
11/16"
11/16"11/16"
11/16"
13/16"*
*
*
1-1-11
11/16"
WMCC416
WMCC616
WMCC418 4000 LB.4000 LB.
6000 LB.
16'
16'
18'6'
6'-6"
6'21"
21"
21"6-1/2" WF
6-1/2" WF
6-1/2" WF
8"
8"8" 16"
22"
18"3"
3"
3"14052
18844
159981256
1402
146511/16"11/16"
WMCC408WMCC410WMCC412
WMCC120
WMCC216
4000 LB.4000 LB.4000 LB.
2000 LB.
1000 LB.
8'10'12'
16'
20'
4'4'4'
6'
6'
12-3/8"12-3/8"12-3/8"
12-3/8"
12-3/8"
6-1/2" WF6-1/2" WF6-1/2" WF
6-1/2" WF
6-1/2" WF
8"8"8"
8"
7"
16-3/8"16-3/8"16-3/8"
16-3/8"
2"2"
2"
2"
2" 98231235914924
16-3/8" 7272
5394
469529589
765
8759/16"
11/16"11/16"11/16"
11/16"
WF INDICATES THAT THIS JIB CRANE USES A WIDE-FLANGE BEAM. THE TROLLEY USED ON THIS CRANEMUST BE DESIGNED TO OPERATE ON A WIDE-FLANGE BEAM.
* THESE CRANES SHIP IN TWO PIECES AND HAVE BOLT ON BOOMS.
WMCC FULL CANTILEVERED JIB CRANE SPECIFICATIONS
1377 Kimberly DriveNeenah, WI 54956-1642Phone (920) 722-0101Fax (920) 725-1394www.contrx.com
MODEL NO. CAPACITY THRUST& PULL (LBS.)A B D FW E F G
WMCC208
WMCC108
WMCC508
WMCC210
WMCC110
WMCC510
WMCC212
WMCC112
WMCC512
WMCC214
WMCC114
WMCC514
WMCC520
WMCC116
WMCC516
WMCC118
WMCC518
2000 LB.2000 LB.2000 LB.
2000 LB.
1000 LB.1000 LB.
1000 LB.1000 LB.1000 LB.
1000 LB.
500 LB.500 LB.500 LB.
500 LB.500 LB.500 LB.
500 LB.
8'
8'
8'
10'
10'
10'
12'
12'
12'
14'
14'
14'
16'
16'
18'
18'20'
4'
3'
3'
5'
3'
3'
5'
3'
4'
5'
4'
4'
4'
4'
4'
4'4'
8"
8"
6"
10-3/8"
8"
6"
10-3/8"
8"
6"
10-3/8"
8"
6"
10-3/8"
8"
10-3/8"
8"10-3/8"
4"
4"
3 3/8"
5-3/4" WF
4"
3 3/8"
5-3/4" WF
4"
3 3/8"
5-3/4" WF
4"
3 3/8"
5-3/4" WF
4"
5-3/4" WF
4"5-3/4" WF
7"
8"
7"7"7"7"7"7"7"
7"7"7"
8"8"
7"7"
7"
12"
10"
12"
10"
12"
12"
16-3/8"
12"
16-3/8"
12"
16-3/8"
12"16-3/8"
2"
2"
2"
2"
2"
2"
2"
2"
2"
2"
2"
2"
2"2"
2"
2"
2"
16-3/8" 5110
3680
2080
WEIGHT(LBS.)
16-3/8" 5226
4662
2641
16-3/8" 6329
5668
2425
16-3/8" 7453
5046
2871
6069
3526
6940
40494967
371
277
205
527
314
230
579
350
304
631
482
329
644
442
696
479747
E
3"
2"
2"
6"
6 BOLTHOLES
FW
B
A4 1/2"
D
END STOP
CONSULT FACTORY FOR:
- Special boom lengths and capacities- Motorized rotation- Mounting hardware- Hinge kits- Matching hoist and trolley systems
BOLT HOLE DIA.
9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"
9/16"
11/16"11/16"11/16"
FWALLBRACKET
VERTICAL BEAM
BOOM
G
2"2"
WALL BRACKETBOLT PATTERN
SALES-WMCC12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
D
A
4-1/2"
B
F
E
FW
WALL BRACKET
6"3"
2"
2"WALL BRACKET
MOUNTINGBOLT PATTERN
2"
2"HINGE PIN
INSTALLATION NOTESNOTE: PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION.
DETERMINE THE SUPPORTING STRUCTURE IS ADEQUATE TO SUPPORT THE CRANE.
USE THE WALL BRACKET PATTERN SHOWN TO MARK AND DRILL THE BOLTHOLES IN THE SUPPORTING STRUCTURE. BE SURE THAT BOTH HINGE PINSSHARE A COMMON TRUE VERTICAL CENTERLINE.
RAISE THE CRANE INTO POSITION AND BOLT THE HINGES TO THE
USE MINIMUM GRADE 5 BOLTS AND NUTS (SUPPLIED BY OTHERS)USE BOLTS 1/16" LESS IN DIAMETER THAN THE BOLT HOLES.
INSTALL HOIST AND TROLLEY BY REMOVING END STOPS.SLIDE THE TROLLEY ONTO THE BOOM AND REPLACE THE END STOPS.
1.
2.
3.
4.
SUPPORTING STRUCTURE.
END STOP
CONTACT CONTRX INDUSTRIES (920) 722-0101 FOR ADDITIONAL ASSISTANCE.5.
(6) HOLES
B
D
E
F
MOUNTING HOLE DIA.
FW
CAPACITY
WEIGHT
A
NOTES • NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
FULL CANTILEVER WALL MOUNT JIB
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
5-2-08
CONTRX INDUSTRIES, INC.
NEENAH, WI 5
4956
920-722-0101
MODEL NO.
SERIAL NO.
OVERBRACED TIE-ROD JIB CRANEWALL MOUNTED
• 180° rotation
• Economical hook coverage with rotation
• Single tie-rod with threaded ends for easy field adjustment
• Mount at any height on wall or building columns where strength permits and true vertical alignment is possible
• High grade steel components for long life
• Hinges with self-lubricating teflon bearings and hardened pins
• Capacity to 6,000 lbs. - standard lengths to 20' 0"
• Primed and painted safety yellow
Options:• Hoists and trolleys• Boom rotation bumpers• Tagline festoon kits• Contact us for special requests.
1-1-11
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394www.contrx.com
WMC OVERBRACED TIE ROD JIB CRANE SPECIFICATIONS
WMC608WMC610WMC612
WMC414
WMC614
WMC420
WMC620
WMC220
WMC618
WMC218
4000 LB.
4000 LB.
6000 LB.6000 LB.
6000 LB.6000 LB.6000 LB.
6000 LB.
2000 LB.2000 LB.
8'10'12'
14'
14'
18'
18'
20'
20'
20'
2'-9"3'-3"4'-0"
4'-6"
4'-9"
6'-3"
6'-0"
6'-6"
7'-0"
6'-0"
8"8"
10-1/2"
8"
10-1/2"
12-3/8" 6-1/2" WF
16"
8"
16"
10-3/8"
4"4"
5-3/4" WF
4"
5-3/4" WF
7" WF
4"
7" WF
5-3/4" WF
8"
8"8"8"8"
8"8"
8"
8"
8" 2'-0"
2'-0"
2'-6"
2'-6"220702319322668
15724
22251
22160
2'-6" 8082
15973
22056
2'-6" 9266
317364560
431
631
963
467
811
1397
671
13/16"13/16"13/16"13/16"11/16"
11/16"
11/16"11/16"
13/16"13/16"
MODEL NO. CAPACITY THRUST& PULL (LBS.)A B D FW E F
WMC408
WMC208
WMC108
WMC508
WMC410
WMC210
WMC110
WMC510
WMC412
WMC212
WMC112
WMC512
WMC214
WMC114
WMC514
WMC120
WMC520
WMC416
WMC616
WMC216
WMC116
WMC516
WMC418
WMC118
WMC518
4000 LB.4000 LB.
4000 LB.4000 LB.4000 LB.
6000 LB.
2000 LB.
2000 LB.2000 LB.2000 LB.
2000 LB.
1000 LB.1000 LB.1000 LB.
1000 LB.1000 LB.1000 LB.
1000 LB.
500 LB.500 LB.500 LB.
500 LB.500 LB.500 LB.
500 LB.
8'
8'
8'
8'
10'
10'
10'
10'
12'
12'
12'
12'
14'
14'
14'
16'
16'
16'
16'
16'
18'
18'
18'
20'
20'
2'-9"
2'-9"
2'-9"
2'-9"
3'-0"
3'-0"
3'-0"
3'-0"
3'-9"
3'-9"
3'-9"
3'-9"
4'-6"
4'-6"
4'-6"
5'-6"
5'-6"
5'-6"
5'-6"
5'-6"
6'-0"
6'-0"
6'-0"
6'-6"
6'-6"
8"
6"
6"
6"
8"
6"
6"
6"
8"
6"
6"
6"
8"
6"
6"
10-3/8"
10-1/2"
8"
6"
6"
10-3/8"
8"
8"
8"
8"
4"
3 3/8"
3 3/8"
3 3/8"
4"
3 3/8"
3 3/8"
3 3/8"
4"
3 3/8"
3 3/8"
3 3/8"
4"
3 3/8"
3 3/8"
5-3/4" WF
5-3/4" WF
4"
3 3/8"
3 3/8"
5-3/4" WF
4"
4"
4"
4"
8"
8"8"
8"8"8"
8"
7"
8"
7"7"7"7"7"7"7"
7"7"7"
8"8"
7"7"7"
7"
1'-3"
1'-3"
1'-3"
1'-3"
1'-6"
1'-6"
1'-6"
1'-6"
1'-9"
1'-9"
2'-0"
2'-0"
2'-0"
2'-0"
2'-3"
2'-3"
2'-0"
2'-0"
2'-3"
2'-3"
2'-0"
2'-0"
2'-3"
2'-3"
14822
1'-3" 7681
4118
2367
WEIGHT(LBS.)
16895
1'-6" 8766
4720
2731
16182
2'-0" 8406
4545
2648
2'-0" 8312
4440
2603
14880
21966
2'-3" 7802
4175
2463
15384
4499
2738
4662
2860
297
202
202
202
341
242
232
232
386
272
261
261
384
292
292
607
702
426
323
323
668
458
458
500
500
E
3"
2"
2"
6"
6 BOLTHOLES
CONSULT FACTORY FOR:
• Special boom lengths and capacities• Motorized rotation
BOLT HOLE DIA.
9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"
9/16"
13/16"
11/16"11/16"
11/16"11/16"11/16"
11/16"11/16"11/16"11/16"
2"2"
WALL BRACKETBOLT PATTERN
FWEND STOP
• Mounting hardware• Hinge kits• Matching hoist and trolley systems
B
4 1/2" A2"
D
F
WALL BRACKETTIE ROD HINGE
TIE ROD
TIE ROD YOKE
HINGE PIN
BOOM BOOM BRACKET
WF INDICATES THAT THIS JIB CRANE USES A WIDE-FLANGE BEAM. THE TROLLEY USED ON THIS CRANEMUST BE DESIGNED TO OPERATE ON A WIDE-FLANGE BEAM.
SALES-WMC12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
A4-1/2"
B
FWD
F
E
WALL BRACKETTIE ROD HINGETIE ROD YOKE
TIE ROD
HINGE PIN
BOOM
BOOM BRACKET
END STOP 2"
INSTALLATION NOTESNOTE: PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION.
DETERMINE THE SUPPORTING STRUCTURE IS ADEQUATE
USE THE WALL BRACKET PATTERN SHOWN TO MARK AND DRILLTHE BOLT HOLES IN THE SUPPORTING STRUCTURE. BE SURE THATBOTH HINGE PINS SHARE A COMMON TRUE VERTICAL CENTERLINE.
BOLT THE UPPER HINGE TO THE MOUNTING SURFACE.USE MINIMUM GRADE 5 BOLTS AND NUTS (SUPPLIED BY OTHERS)USE BOLTS 1/16" LESS IN DIAMETER THAN THE BOLT HOLES.
INSTALL HOIST AND TROLLEY BY REMOVING END STOPS.SLIDE THE TROLLEY ONTO THE BOOM AND REPLACE THE END STOPS.
1.
2.
3.
6.
CONTACT CONTRX INDUSTRIES (920) 722-0101 FOR ADDITIONAL ASSISTANCE.7.
WHILE SUPPORTING THE BOOM HORIZONTALLY, BOLT THE LOWERHINGE AND BEAM TO THE MOUNTING SURFACE.
4.
ATTACH THE ROD BETWEEN THE UPPER HINGE AND BOOM BRACKET WITH THENUTS AND WASHERS PROVIDED. ADJUST THE NUTS TO LEVEL THE BOOM.
5.
6"3"
2"
2"WALL BRACKET
MOUNTINGBOLT PATTERN
2"
2"
TO SUPPORT THE CRANE.
(6) HOLES
B
D
E
F
MOUNTING HOLE DIA.
FW
CAPACITY
WEIGHT
A
NOTES • NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
OVERBRACED TIE ROD WALL MOUNT JIB
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
7-31-08
CONTRX INDUSTRIES, IN
C.
NEENAH, WI 5
4956
920-722-0101
MODEL NO.
SERIAL NO.
PILLAR MOUNTJIB CRANE
• 360° rotation
• Ideal for maximum headroom and trolley travel
• High grade steel components for long life
• Mounting plates with spherical roller bearings
• Capacities to 4,000 lbs. - standard lengths to 20'
• Primed and painted safety yellow
Options:• Hoists and trolleys• Tagline festoon kits• Contact us for more information
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
10-8-03
PORTABLE GANTRY CRANES
• Automotive• Trucking• Manufacturing• Loading Docks• Aircraft• Implement• Marine• Warehouses• Maintenance
• Capacities From 1 to 5 Ton• Spans from 8 to 16 Feet• Heights from 8 to 16 Feet• Portable• Custom Sizes Available• 2 Large Steel Swivel Casters• 2 Large Steel Swivel Casters with Brakes• Standard "I" Beams• Painted Safety Yellow• Built to meet ANSI and OSHA Requirements
APPLICATIONS OF FIXED HEIGHT &TELESCOPING GANTRIES
FEATURES OFFIXED HEIGHT &TELESCOPING GANTRIES
TelescopingGantry Crane
Fixed HeightGantry Crane
2-2-11
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394
PORTABLE GANTRY CRANE SPECIFICATIONS
www.contrx.com
FIXED & TELESCOPING GANTRY CRANESSemi-steel heavy-duty swivel casters with rollerbearings are standard equipment. Two casters are supplied with brakes.
Gantries are easily disassembled and assembled for relocation.
Contact factory for special heights, spans, and options.
Our Fixed Height Gantry Cranes are ideal for use in aircraft, automotive, and marine repair shops. They also work wellin warehouses, machine shops, and loading areas. Gantry cranes are supplied with four roller-bearing steel wheelsfor easy maneuverability. The structural steel legs are welded together at the factory. Gantry crane requires assemblybefore use.
Our Telescopic Height Gantry Cranes have the same abilities as our fixed height gantries with the added benefit ofraising or lowering the beam to suit your need. The beam will adjust from 8'-0" to 12'-0" below the beam withpositive stops every 6". The beam is raised and lowered with the aid of two cable pullers (included). Locking pinshold the beam at the desired height.
GCT1-12
GC1-12
GCT1-16
GC1-16
GCT2-8
GC2-8
GCT2-12
GC2-12
GCT2-16
GC2-16
GCT3-8
GC3-8
GCT3-12
GC3-12
GCT3-16
GC3-16
GCT4-8
GC4-8
GCT4-12
GC4-12
GCT4-16
GC4-16
GCT5-8
GC5-8
GCT5-12
GC5-12
GCT5-16
GC5-16
GCT1-8
GC1-8
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
1
1
5" X 1 5/8"
5" X 1 5/8"
5" X 1 5/8"
5" X 1 5/8"
8" X 1 1/2"
8" X 1 1/2"
8" X 1 1/2"
8" X 1 1/2"
8" X 1 1/2"
8" X 1 1/2"
8" X 2 1/2"
8" X 2 1/2"
8" X 2 1/2"
8" X 2 1/2"
8" X 2 1/2"
8" X 2 1/2"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
8" X 3"
5" X 1 5/8"
5" X 1 5/8"
13'-5 9/16"
13'-5"
17'-5 9/16"
17'-5"
9'-6 5/8"
9'-6"
13'-6 5/8"
13'-6"
17'-6 5/8"
17'-6'
9'-6 5/8"
9'-6 5/8"
13'-6 5/8"
13'-6 5/8"
17'-6 5/8"
17'-6 5/8"
9'-8 5/8"
9'-8 5/8"
9'-8 5/8"
9'-8 5/8"
13'-8 5/8"
13'-8 5/8"
13'-8 5/8"
13'-8 5/8"
17'-8 5/8"
17'-8 5/8"
17'-8 5/8"
17'-8 5/8"
9'-5 9/16"
9'-5"
12'
12'
12'
12'
12'
12'
12'
12'
12'
12'
16'
16'
16'
16'
16'
16'
16'
16'
16'
16'
8'
8'
8'
8'
8'
8'
8'
8'
8'
8'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
5'
8'
8'
8'
8'
8'
10'
8'
8'
8'
8'
8'
10'
12'
12'
12'
12'
12'
10'
12'
12'
12'
12'
12'
10'
12'
12'
12'
12'
12'
10'10'10'10'10'10'10'10'10'10'
8'
8'
8'
8'
8'
10'
3 3/8"
3 3/8"
4"
4"
3 3/8"
3 3/8"
4"
4"
5-3/4"
5-3/4"
8"
8"
7-1/8"
7-1/8"
4"
4"
8"
8"
7-1/8"
7-1/8"
5-3/4"
5-3/4"
8"
8"
7-1/8"
7-1/8"
8"
8"
3"
3"
807
600
957
750
886
651
1016
781
1266
1030
1202
1018
1431
1247
1778
1594
1607
1393
1763
1549
1989
1776
1865
1651
2093
1879
2321
2107
733
5266"8"6"8"
10-3/8"
9-7/8"
16-3/8"
8"
9-7/8"
16-3/8"
10-1/2"
13-5/8"
16-3/8"
13-5/8"
5"
MODELNUMBER
MODELNUMBER
CAP.(TONS)
CAP.(TONS)
STEELWHEELS
STEELWHEELS
C
C
D
D
E
E
F
F G
FW
FW
WEIGHT(LBS.)
WEIGHT(LBS.)
MIN. MAX.
FIXED HEIGHT GANTRY CRANE SPECIFICATIONS
TELESCOPING HEIGHT GANTRY CRANE SPECIFICATIONS
C FW
FLOOR
FLOOR
D
FWC
D
E
E
F
F
G
G
CABLEPULLER(2)
* DIAMETER OF WHEELS BY TREAD WIDTH** "S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam.
* DIAMETER OF WHEELS BY TREAD WIDTH** "S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam.
*
* BEAMTYPE**
SSSSWSWWWWWWWW
S
BEAMTYPE**
SSSSWSWWWWWWWW
S6"8"6"8"
10-3/8"
9-7/8"
16-3/8"
8"
9-7/8"
16-3/8"
10-1/2"
13-5/8"
16-3/8"
13-5/8"
5"
G
OPTIONS: • (2) STEEL SWIVEL CASTERS • (2) STEEL SWIVEL CASTERS WITH BRAKES SALES-GC
12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
C
D
G
FW
F
E
W
D
E
F
G
W
FW
CAPACITY
WEIGHT
C
NOTES • NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
FIXED HEIGHT GANTRY CRANE
OPTIONS: • (2) STEEL SWIVEL CASTERS • (2) STEEL SWIVEL CASTERS WITH BRAKES • HEIGHT IS ADJUSTABLE IN 6" INCREMENTS
SALES-GCT12-13-05WJ
1377 Kimberly Dr., Neenah, WI 54956www.contrx.com
C
D
G
FW
MAXMIN
E
W
CABLE PULLER(2) INCLUDED
D
E
G
FW
MAX
MIN
W
CAPACITY
WEIGHT
C
NOTES • NOT DESIGNED FOR OUTDOOR USE
NOT TO SCALEDATE
DWG NO
TELESCOPING GANTRY CRANE
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
1
2
10-29-10
3
4
5
6
7
Alternate Hook PositionsTelescoping BoomBoom HandleSafety Swivel Hooks (2)Fork Pockets48" Safety Chain with Grab HookSpring Loaded Boom Lock
• Converts lift truck into a crane inexpensively• Moves cumbersome items your forks can't reach.• Crane reaches out and picks up from overhead.• Reaches through or over obstructions.
Minimize manhandling of shipments andequipment without investing a lot of money
in new power equipment. Jib lift lets youconvert your standard lift truck into a mobilecrane at minimal cost. You can enjoy the
convenience of this versatile equipment without duplicating power equipment...and it's easy touse. One man can install in minutes withoutremoving forks, just by slipping onto forks. 48" safety chain anchors it to truck's frame.Constructed of heavy structural steel tubing;
two safety swivel hooks provided.
1
6
3
4
2
7
5
TELESCOPING JIB LIFT
Check with manufacturerof your lift truck for load
capabilities before using.
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394www.contrx.com
145" MAX
SW
TL
H.U.B.
HOOKPOSITION
9
CENTER OFGRAVITY
BOOM CONTRACTED
BOOM EXTENDED
CENTER OFGRAVITY
SAFETY PIN LOCKSBOOM IN POSITION
SAFETY PIN LOCKSBOOM IN POSITION
IMPORTANT
CENTER OF GRAVITY LOCATION
TRUCK FORKS MUSTEXTEND THROUGH FULLLENGTH OF FORK TUBES
FEATURES• Handles long loads in closed trucks• High and long reaches for inaccessible areas• High underclearances and bulky load handling
A B C D EHOOK POSITION
85" MIN
TL
H.U.B.
A B C D EHOOK POSITION
HOOKPOSITION
1
OAHY
Y
X
XX
SINGLE HOOK CAPACITIES
HookPos.
123456789
HookPosition(inches)
8087-1/2
95102-1/2
110117-1/2
125132-1/2
140
4000LB.
CAP.
400035353167286826212413223520821949
6000LB.
CAP.
600053024750430239313619335331232923
8000LB.
CAP.
800069746182555150374610425039423676
CAP.(LBS)
MODELNUMBER
DIM."S"
DIM."W"
DIM."X"
DIM."Y"
DIM."XX"
DIM."TL"
DIM."H.U.B."
WT.(LBS)
4000 JLT411 11" 17"30.3" 10.6"46.0"29.4" 10.3"44.4"28.6" 10.0"42.9"27.9" 9.7"41.5"32.2" 11.7"49.8"31.3" 11.4"48.1"30.5" 11.2"46.7"29.8" 11.0"45.4"29.2" 10.8"44.2"33.4" 11.7"50.8"30.7" 10.4"45.5"28.7" 10.9"41.5"
32.3" 11.4"49.7"24" 10" 3734000 JLT424 24" 30" 24" 4134000 JLT430 30" 36" 24" 4344000 JLT436 36" 42" 24" 4554000 JLT442 42" 48" 24" 4766000 JLT613 13" 21" 24" 519
TELESCOPING JIB LIFT
01-27-12
FORKPOCKETS
2-1/2" X 5-1/2"2-1/2" X 5-1/2"2-1/2" X 5-1/2"2-1/2" X 5-1/2"2-1/2" X 5-1/2"3-1/2" X 7-1/2"
6000 JLT624 24" 32" 24" 5446000 JLT630 30" 38" 24" 5666000 JLT636 36" 44" 24" 5886000 JLT642 42" 50" 24" 6108000 JLT824 24" 32" 32" 6678000 JLT836 36" 44" 32" 7878000 JLT848 48" 56" 32" 12" 909
10"10"10"10"10"10"10"10"10"10"10"
3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"
E 74 4000 6000 8000D 64 4000 6000 8000C 54 4000 6000 8000B 44 4000 6000 8000A 34 4000 6000 8000
DIM."OAH"
19"19"19"19"19"19"19"19"19"19"20"20"22"
THIS CHART LISTS SAFE WORKING LOADSFOR THE JIB LIFT ONLY. IT DOES NOT
CONSIDER THE FORK TRUCK BEING USED.CONSULT THE FORK TRUCK MANUFACTURER
FOR SAFE LOAD CAPABILITIES WITHTHIS ATTACHMENT BEFORE USING.
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
1
2
10-29-10
3
4
5
6
7
8
2
7
6
8
3
4
1
5
Alternate Hook Positions
Telescoping Boom
Boom Handle
Safety Swivel Hook
Fork Pockets
48" Safety Chain with Grab Hook
Spring Loaded Boom Lock
Angle Adjusting Pin
• Converts lift truck into a crane inexpensively• Moves cumbersome items your forks can't reach.• Crane reaches out and picks up from overhead.• Increases load height• Adjustable boom height and reach• Reaches through or over obstructions.
Pivoting jib lift lets you convert your standard lift truckinto a mobile crane in minutes at minimal cost. Lift loadshigher than your lift truck forks can reach. Pivoting boomadjusts from horizontal to 50°. Enjoy the convenience of
this versatile attachment without duplicating existingequipment ...and it's easy to use. One person can install
without removing forks. 48" safety chain ties jib lift totruck frame. Constructed of heavy structural steel tubing;
one swivel hook provided.
PIVOT BOOM JIB LIFT
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394www.contrx.com
SW
FEATURES• Handles long loads in closed trucks• High and long reaches for inaccessible areas• High underclearances and bulky load handling• Adjustable at 10° increments from horizontal to 50°• Safety chain secures jib lift to forklift truck
143-3/8" MAX
IMPORTANTTRUCK FORKS MUST
EXTEND THROUGH FULLLENGTH OF FORK TUBES
83-3/8" MIN
H.U.B.
H.U.B.
BOOM CONTRACTED
BOOM EXTENDEDXX
X
TL
TL
SAFETY PIN LOCKSBOOM IN POSITION
HOOKPOSITION
9
A B C D EHOOK POSITION
HOOKPOSITION
1
A B C D EHOOK POSITION
SAFETY PIN LOCKSBOOM IN POSITION
Y
Y
OAH
CENTER OFGRAVITY
CENTER OFGRAVITY
CENTER OF GRAVITY LOCATION
CAP.(LBS)
MODELNUMBER
DIM."S"
DIM."W"
DIM."TL"
DIM."H.U.B."
WT.(LBS)
4000 PB-JLT424 24" 30" 24" 18-1/2" 4914000 PB-JLT436 36" 44" 24" 19-1/2" 5886000 PB-JLT624 24" 32" 24" 19-1/2" 6406000 PB-JLT636 36" 44" 24" 23-1/2" 7188000 PB-JLT836 36" 44" 32" 27-1/2" 9668000 PB-JLT848 48" 56" 32" 27-1/2" 1025
PIVOT BOOM JIB LIFT
01-27-12
SINGLE HOOK CAPACITIES
HookPos.
123456789
HookPosition(inches)
8087-1/2
95102-1/2
110117-1/2
125132-1/2
140
4000LB.
CAP.
400035353167286826212413223520821949
6000LB.
CAP.
600053024750430239313619335331232923
8000LB.
CAP.
800069746182555150374610425039423676
E 74 4000 6000 8000D 64 4000 6000 8000C 54 4000 6000 8000B 44 4000 6000 8000A 34 4000 6000 8000
THIS CHART LISTS SAFE WORKING LOADSFOR THE JIB LIFT ONLY. IT DOES NOT
CONSIDER THE FORK TRUCK BEING USED.CONSULT THE FORK TRUCK MANUFACTURER
FOR SAFE LOAD CAPABILITIES WITHTHIS ATTACHMENT BEFORE USING.
FORKPOCKETS
2-1/2" X 5-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"
DIM."OAH"30-1/2"31-1/2"
32"36"
41-3/4"41-3/4"
DIM."X"
DIM."Y"
DIM."XX"
25.2"27.0"25.5"26.0"24.6"
26.7"16.7"16.2"17.2"19.7"17.4"
16.5"36.5"41.2"38.2"38.0"35.0"
39.7"
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
8-16-02
PALLET LIFTER
Contrx Standard Pallet Lifters make your crane into an inexpensive forklift. You can afford palletlifting convenience at a small cost. Speed up handling and movement of pallet loads, loadingand unloading. Reach areas such as flat and gondola cars, open top trucks, and congestedareas with a pallet lifter. Contrx brand pallet lifters are designed to hang level when empty or
with a properly balanced load. See table on reverse side for capacities and dimensions.Contact your local dealer for custom dimensions.
1377 Kimberly DriveNeenah, WI 54956-1642
Phone (920) 722-0101Fax (920) 725-1394
PALLET LIFTERDIMENSION & WEIGHT CHART
www.contrx.com4-1-08
Smaller pallets may be lifted as long as theircenter of gravity is located under the lifting bail.
Specify hook size when ordering to ensurecompatibility with lifting bail size.
G
A
B
F
Handle
LiftingBail
Center of gravityof lifter & load.
MODELPL524PL530PL536PL542PL548PL130PL136PL142PL148PL236PL242PL248PL336PL342PL348PL436PL442PL448PL636PL642PL648PL836PL842PL848
PL1036PL1042PL1048
CAP(lbs.)5005005005005001000100010001000200020002000300030003000400040004000600060006000800080008000
10,00010,00010,000
A(in.)243036424830364248364248364248364248364248364248364248
B(in.)121518212415182124182124182124182124182124182124182124
F(in.)202025252520252525252525252525252525272727272727272730
G(in.)484848484848484848484848484848484848484848484848484848
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
11-19-02
BRIDGECRANES
DOUBLE GIRDERTOP RUNNING
• Double reduction helical gearmotor for reduced wear and long life
• Adjustable torque magnetic disc brake for smooth operation
• Machined steel crane and trolley wheels for smooth and quiet operation
• Top quality hoists matched to the duty required for each bridge crane
• Custom engineered to fit your application
• Independent traveling pendant• Variable frequency type drive motor control• Radio remote control operation• Travel limit switches, warning lights, & horn• 60 minute motors & special insulation• Catwalks & service platforms• Heat shields• Runway rails & beams
Available custom optionsStandard options
CONTRX INDUSTRIES1377 Kimberly Drive
Neenah, WI 54956-1642Phone (920) 722-0101
Fax (920) 725-1394www.contrx.com
11-19-02
TYPES OF STANDARD BRIDGE CRANESDOUBLE GIRDERTOP RUNNINGWITH DUALOUTRIGGERS
SINGLE GIRDERTOP RUNNINGWITH SINGLEOUTRIGGER
SINGLE GIRDERUNDER RUNNINGWITH DUALOUTRIGGERS
SINGLE GIRDERUNDER RUNNINGWITH NOOUTRIGGERS
SINGLE GIRDERTOP RUNNINGWITH CAPCHANNEL
CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Fax
www.contrx.com
TERMS OF SALE
TERMS OF BILLING: NET 30 DAYS TO APPROVED ACCOUNTS 1 1/2% Interest Charged on Past Due over 39 days from date on Invoice. FREIGHT TERMS: All Products Shipped Freight Collect or Prepaid-3rd Party Billing. All shipments are made F.O.B Neenah, Wisconsin. When the shipment leaves our dock it becomes the property of the Distributor. Any claims for damage or shortages must be made by the Distributor. (SEE FORM CX11491) RETURNS: 20% restocking charge on all returns. Returns must be shipped freight Prepaid. SPECIALS: Specially fabricated orders are not returnable.
All merchandise is sold F.O.B. Contrx Factory, Neenah, WI. Title to the merchandise is transferred to the Distributor at the time the Carrier accepts the shipment. Any claims for loss, damage, or tracers for lost items in transit MUST BE FILED BY THE DISTRIBUTOR WITH THE CARRIER. Suitable copies of Bill of Lading will be furnished upon request if the Distributor has occasion to file a claim with the carrier. There are three types of claims that occur on shipments to customers. 1. Loss or short on delivery. 2. Visible damage at time of delivery. 3. Concealed damage noted after delivery. There are three steps to take before signing a carrier delivery receipt. 1. Count the number of pieces and compare against count on the freight bill. 2. Visually inspect each piece for damage. 3. Read the labels and packing slips to be sure the freight belongs to you. LOSS OR SHORT ON DELIVERY 1. If the shipment is not received within ten working days after the known ship date, contact CONTRX Customer Service for the shipping information necessary for you to file a tracer. 2. If a shipment is delivered short and the shortage is not delivered within 48 hours, contact CONTRX for the shipping information so you can file a tracer. VISIBLE DAMAGE AT TIME OF DELIVERY 1 DO NOT REFUSE THE SHIPMENT or return damaged merchandise to CONTRX without authorization. 2. The customer should immediately inspect the damage with the driver. 3. The specific damage should be noted on both the customers copy and the carrier copy of the freight bill. The driver should sign both copies. 4. Set the damaged merchandise aside and contact the carrier for an inspection. CONCEALED DAMAGE NOTED AFTER DELIVERY 1. Concealed damage must be reported to the carrier as soon as possible. 2. Call the Carrier for an inspection. 3. Follow the same procedure as for visible damage at the time of delivery. 4. Any freight transferred after delivery that may have concealed damage is not recoverable by the Carrier or CONTRX. FILING THE CLAIM 1. There are four basic documents necessary to support your claim. a. Delivery receipt with noted exceptions. b. Inspection report from the carrier. c. Cost of parts to repair the damage. (Repair Invoice) d. CONTRX Invoice showing the cost of the product. 2. There is a nine month statute from date of receipt for filing a loss or damage claim. 3. CONTRX Customer Service Department will provide any information or assistance to help resolve a loss or damage claim you have filed.
MEMO TO DISTRIBUTORS CONCERNING LOSS AND DAMAGE CLAIMS
FORM: CX11491
1. CONTRX Industries warrants products it manufactures against defects in materials and workmanship for a period of one year from date of receipt by the purchaser or his customer, or one year from time of completion of initial field installation if installed by CONTRX. CONTRX agrees to furnish the same or substantially similar replacement part (new or repaired) free of charge, F.O.B. site, providing the buyer gives immediate written notice of alleged defects and, if requested by CONTRX, returns the defective parts to our factory, freight collect, for our inspection and examination.
2. This warranty applies only to CONTRX equipment or materials which, after our inspection is determined to be defective either in material supplied or workmanship performed by CONTRX. Where equipment is furnished by CONTRX but not of its manufacture, CONTRX’S liability is limited to such adjustment as the actual manufacturer makes to CONTRX.
3. CONTRX will not be liable for the cost of repairs, alterations, or replacements or any expense connected therewith made or incurred by the purchaser or his agents or employees, except upon written authority from the CONTRX office.
4. This warranty is personal to purchaser only and applies only to equipment the purchaser has properly installed, operated and maintained in accordance with CONTRX’S written instructions.
5. CONTRX assumes no liability for any consequential damages suffered through the use or loss of use of its equipment.
6. This constitutes CONTRX’S sole warranty with respect to the equipment and material manufactured by itself. CONTRX makes no other warranty of any kind whatsoever, expressed or implied, and all implied warranties of merchantability and fitness for a particular purpose which exceed the aforementioned obligation are hereby disclaimed by CONTRX Industries.
CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Fax
www.contrx.com
PRODUCT WARRANTY
top related