aluminum roughing & finishing
TRANSCRIPT
-
7/28/2019 Aluminum Roughing & Finishing
1/2
Aluminum Roughing & Finishing
Micro grain Carbide End MillsRuns 50% to 300% faster in Aluminum
Longer Tool Life
Faster Feed RatesBetter Chip Evacuation
Less Tool Deflection
Leaves Superior Finishes
Metric, and Specials available on
request
Radius and Left Hand available on
request
The Swift-CARBCNC TM manufactured End Mill is a High Performance, High Helix tool, w hich
has tighter control and tolerances on circle ground margins, double rake polished flutes,
and micro finishes. Increased speeds are obtainable with Swift-CARBCNC TM allowing you to
remove material up to 10 times faster. This means increased productivity and higher profits
off your shop floor. The Swift-CARBCNC TM End Mill is designed for slotting, profiling, and
ramping at high speeds and feeds which makes it perfect for the machining of nonferrous
materials (Aluminum, Plastics, and Copper Alloys).
Swift-CARBCNC TM Aluminum Series "SC" - High Helix - 2 & 3 Flute
Chip
Load
Chart
Dia of
End Mill
Materials: Aluminum or Plastics Materials: Copper
2 FluteSFM 450-1200Speed
RPM
Feed
IPM
3 FluteSFM 450-1200Speed
RPM
Feed
IPM
2 FluteSFM 200-600Speed
RPM
Feed
IPM
3 FluteSFM 200-600Speed
RPM
Feed
IPM
.0003 - .0008
.0004 - .0012
.0005 - .0015
.0010 - .0050
.0012 - .0055
.0020 - .0070
.0020 - .0080
.0025 - .0100
.0030 - .0150
.0020 - .0150
.0030 - .0160
.0030 - .0160
1/8
3/16
1/4
3/8
7/161/2
9/16
5/8
3/4
7/8
1
1-1/4
MAX 15 - 100
9170 - MAX 20 - 125
6880 - MAX 25 - 130
4580- 12,000 25 - 140
3930 - 10,500 30 - 1503440 - 9170 30 - 150
3060 - 8150 30 - 160
2750 - 7340 30 - 160
2290 - 6110 30 - 165
1970 - 5240 30 - 165
1720 - 4590 30 - 170
1375 - 3660 30 - 170
MAX 22 - 125
9170 - MAX 30 - 135
6880 - MAX 30 - 135
4580- 12,000 35 - 150
3930 - 10,500 35 - 1503440 - 9170 35 - 160
3060 - 8150 40 - 180
2750 - 7340 40 - 180
2290 - 6110 40 - 185
1970 - 5240 40 - 185
1720 - 4590 40 - 195
1375 - 3660 40 - 195
6110 - MAX 8 - 50
4080- 12,000 8 - 50
3060 - 9170 10 - 50
2040 - 6110 10 - 50
1750 - 5250 15 - 601530 - 4590 15 - 60
1360 - 4080 15 - 65
1220 - 3670 15 - 65
1020 - 3060 18 - 75
870- 2620 18 - 75
770- 2290 18 - 75
600 - 1830 18 - 75
6110 - MAX 12 - 65
4080- 12,000 12 - 65
3060 - 9170 15 - 75
2040 - 6110 15 - 75
1750 - 5250 18 - 751530 - 4590 18 - 75
1360 - 4080 20 - 75
1220 - 3670 20 - 75
1020 - 3060 25 - 85
870- 2620 25 - 85
770- 2290 25 - 95
600 - 1830 25 - 90
The Speeds and Feeds recommended on the aluminum charts are for starting points only.
TERM EQUATION RESULT
Revolution
SpeedRPM = 3.82 x SFPM Dia. = Required RPM
HomeHome
Shopping CartShopping Cart
Product ListProduct List
Ordering InfoOrdering Info
Swift-CarbSwift-Carb
Carbide End MillsCarbide End Mills
New TechNew Tech
SuperbeeSuperbee
PMTPMT
Micro ToolsMicro Tools
Hot USAHot USA
Carbide MillsCarbide Mills
XLN CuttingXLN Cutting
ToolsTools
GorillaGorilla
MillMill
SpecialsSpecials
ExtendedExtended
QuantityQuantity
ToolTool
SearchSearch
-
7/28/2019 Aluminum Roughing & Finishing
2/2
Surface Feet per Minute SFPM = .262 x Dia. x RPM = Surface Feet per Minute
Inches per MinuteIPM = RPM x Inches per Tooth x
No. of Teeth
= Inches per Minute in
Travel
Feed per Tooth Inches
per ToothIPT = IPM RPM No. of Flutes
= Chip Load per Tooth Per
Revolution
Questions? Send a email to [email protected]
or give us a call at 888-305-TOOL or send a Fax to 888-649-TOOL
End Mill Discount only sells tools made in the USA.
Copyright 2010 End Mill Discount