aluminium profile system - alutech...
TRANSCRIPT
ALUMINIUMPROFILESYSTEM
Content
ALT110 OFFICE PARTITIONS SYSTEM
ALT111 INTERIOR PARTITION WALLS SYSTEM
ALT115 FULL GLASS PARTITION WALL SYSTEM
ALT118 LIGHT PARTITION WALLS SYSTEM
2
Office partitions are designed to organize working space and to create various functional rooms: offices,
corridors, halls, working and trade places, etc.
3
APPLICATION AREA
Nonresidential buildings, renovation of business-centres and offices
Bank system development
Building of shopping centres, hypermarkets, supermarkets
4
APPLICATION AREA
OFFICE PARTITIONS SYSTEMALT110
5
The system doesn’t require specific equipment and tools for ALT110 system installation and assemblage
Profile is supplied:- coated according to the RAL- Anodized- mill-finished
Owing to unique design peculiarities ALT110 has more advantages among other systems.
ALT110 SYSTEM DESCRIPTION
6
The widest range of glazing and infill unit. Glass of 4,5,6,8 mm thickness can be used as translucent infill unit.
It’s possible to use gypsum plasterboard, flake board, vinyl-covered gypsum board, MDF and other types of infill units from 4 up to 16 mm !!!
SYSTEM APPORTUNITIES
7
Decorative cups are performed in two types: straight and rounded. It enables to create interior partitions in high-tech style or to use smooth forms.
It is possible to assemble single- and two-leafed aluminium doors with single or double infill unit Door with double glass infill unit can be completed with integrated shutter
SYSTEM APPORTUNITIES
8
SYSTEM APPORTUNITIES ALT110SYSTEM APPORTUNITIES
9
Rotary profiles enable to create different types of angles
It is possible of joining to walls at any angles without panel strips.
It is possible to create two-, three- and four-directional units.
SYSTEM APPORTUNITIES
10
The system has basic, economical and heavy types of mullions.
Visible width of economical mullion is only 30 mm.
SYSTEM APPORTUNITIES
11
Calculation of tolerant height
SYSTEM APPORTUNITIES
12
Partitions are assembled with steel corners, self-tapping screws without preliminary drilling of profiles.
This solution enables transom installation without sequenced assemblage even if the mullions have already been installed.
Grooves in the corners permit to set horizontally transom without drilling additional holes in the mullion.
Steel corners permit to cover assemblage mistakes up to 5 cm while cutting transoms.
Post can be fixed to floor and ceiling using this corner solution.
SYSTEM APPORTUNITIES
13
Special profile permits to lay electric, telephone and computer
cables inside the partition. It’s possible to install sockets on both
sides.
SYSTEM APPORTUNITIES
14
15
Three types of door instal into one frame
Frame profile110.0104
SYSTEM APPORTUNITIES
15
SYSTEM APPORTUNITIES
16
КОНДУКТОРЫCONDUCTOR
17
КОНДУКТОРЫTRANSOM BAR AND BASEMENT ASSEMBLAGE
18
TRANSOM BAR AND BASEMENT ASSEMBLAGE
19
Posts can be fastened to ceiling and floor using insert elements
SYSTEM APPORTUNITIES
20
The system has end plugs which confer partitions more presentable and aesthetic look from top view
SYSTEM APPORTUNITIES
21
ФУРНИТУРА
Door hinges, handles, door locks, latch strike plates are bought together with profile
Recommended accessories articles are given in the catalogue
ACCESSORIES
22
PORTFOLIO
23
PORTFOLIO
24
PORTFOLIOPORTFOLIO
25
PORTFOLIOPORTFOLIO
26
INTERIOR PARTITIONS SYSTEMALT111
Low metal consumption – competitive price
The easiest assemblage and disassemblage:
Assemble of partitions over 4 m;
Ergonomic and functional system features permit to be competitive in the market.
ALT 111 SYSTEM DESIGNING AIMS
28
Unique clamping:
1. Easy assemblage2. Infill unit can be installed and disassembled separately3.Secure clamp fixation under loading impact: 1 clamp carries 45-48 kg. 4. Grooves of small depth improve inertia characteristics of aluminium profiles and cut its metal consumption.
PATENT
KEY FEATURES
29
INFILL UNIT TYPES
30
Mullion-transom fixation
Double and single infill units
KEY FEATURES
31
KEY FEATURES
32
Fixing to floor and ceiling
KEY FEATURES
33
Three types of door installation into one frame
KEY FEATURES
34
Advantages:
Improved weight permit to cut down price by 15%
Owing to additional gap profile has more elegant look
Changed shape and improved weight make new frame profile more attractive aesthetically and up-to-date
111.0115 DOOR FRAME
35
Cover cup profile
ALT111 SYSTEM APPORTUNITIES
36
ALT111 SYSTEM APPORTUNITIES
Single infill unit
Double infill unit
37
Range of wall widths:from 75 up to ∞ mm
EXTENSIBLE DOOR CASE
38
Wall width from 75 up to 105 mm
Wall width from 135 up to 270 mm
Wall width from 105 up to 135 mm
EXTENSIBLE DOOR CASE
39
EXTENSIBLE DOOR CASE
40
ADVANTAGES:
Lock strike plate is assembled without milling;
No visible fittings;
Unit can be adjusted with spacer bulb and it is assembled easier and faster.
Aluminium door case is durable and doesn’t require additional maintenance.
EXTENSIBLE DOOR CASE
41
AYPC.111.0118 RECTANGLUGAR DOOR FRAME
42
SLIDING DOORS
43
AYPC.111.0702
AYPC.111.0705
SLIDING DOORS
44
AYPC.111.0701
SLIDING DOORS
45
Reinforced transom gives to guide transom an additional support pointthrough second-level transom.
AYPC.111.0707
SLIDING DOORS
46
Maximum load on two rollers is160 kg.
AYPC.111.0750
R460
SLIDING DOORS
47
111SL06/16/E6
FRK104
SLIDING DOORS
48
If necessary before infill unitsinstallation it should be made lastadjusting of rollers through wholein a transom.
SLIDING DOORS
49
SLIDING DOORS
50
SLIDING DOORS (assemblage sequence)
51
Opening stops areassembled intoguide at the sametime
SLIDING DOORS (assemblage sequence)
52
SLIDING DOORS (assemblage sequence)
In fixed part infill unit is assembled with theclamps 111.0901 and 111.0902 what are hiddenby decorative cover caps.
53
KEY FEATURES:
The hinge is fixed with insert element permitting to adjust height;
After final adjustment hinges are additionally fixed with self-tapping screws;
The hinge has horizontal micrometer adjustment ± 1,8 mm
Ledge is adjusted within ± 0,5 mm
Maximum loads: 2 hinges – up to 85 kg 3 hinges – up to 115 kg
AYPC.111.1006 REINFORCED HINGE
54
KEY FEATURES:
The hinge is fixed on frame profile with insert element permitting to adjust height;
After final adjustment the hinge is fixed with adjusting screw;
The hinge permits horizontal adjustment of glass;
Hinge dimensions - 88 х 45 mm;
The hinge is assembled on glass sash of 8 and 10 mm thickness.
Maximum loads: 2 hinges – up to 80 kg 3 hinges – up to 100 kg
111.1003 M REINFORCED HINGE FOR GLASS DOORS
55
The transparent protective film is intended for protecting frame profile surface from damage lock catch.
PROTECTIVE FILM art. 15x45-3М
Features of the protective film 15x45-3М: The film is supplied as a rectangle with dimensions 45х15мм, 5 pcs., on the stand; The film is glued on frame door profile and on strike plate as well (the strike plate is used for full-glass sash manufacturing) The film doesn’t become deformed and unglued in the operation (approved with internal tests). 56
PLUG 111.0905
The plastic plug 111.0905 is intended for decorating cover caps corner joint on the angle of 45°.
For AYPC.111.0905 plug the cover cap profiles are cut on the angle of 90°.
57
ALT111 SYSTEM APPORTUNITIES
58
ALT111 SYSTEM APPORTUNITIES
59
60
ALT111 SYSTEM APPORTUNITIES
Decorative end plugs complete elegant look of the system
DECORATIVE END PLUGS
61
LEVELING PROFILE 111.0116
Key features:
The bush 06501 (Giesse) is used for smooth adjustment
Holes in profiles fitted for hex-nut wrench for adjusting 06501 bush and enables profile final fixation;
If it’s necessary, AYPC.111.0116 leveling profile can be used together with gaskets.
62
Assemblage order
63
Distance between mullions, cm.
Height of partition mullions depending on distance between mullions(under standard wind load 0,001 kg/cm2
Hei
ght o
f mul
lions
, cm
.CALCULATION OF PERMISSIBLE HEIGHT
64
65
КОНДУКТОРЫJIGS
AYPC.111.1101
AYPC.111.1100
CUTTING• disk electric saw• milling machine (for lock installation);
DRILLING• drill with perforator;•screwdriver;
MEASURING•tape measure;•level;•setsquare;
AUXILIARY•Kit of metal drills•Vacuum cups;•knee;•stepladder;•marker.
EQUIPMENT AND TOOLS
66
67
SAMPLES
68
SAMPLES
69
PORTFOLIO
70
PORTFOLIO
71
PORTFOLIO
72
PORTFOLIO
FULL GLASS PARTITIONS ALT115
Full glass partitions system is used for creating of salesrooms, boutiquesand shops in shopping centers.Full glass partitions are efficient solution for offices following “open space”concept.
APPLICATION AREA
74
Insert
SYSTEM COMPONENTS
U-profile
Cover profileClip
Guide
75
The multi-use clip has three longitudinal grooves with variousdepth. Grooves in connection with jut of the guide ensurerequired space dimensions (8, 10, 12 mm) in connection “insert-clip”. Thereby, the same clip is used for glass of 8, 10 and 12mm thickness.
76
MULTIFUNCTIONAL CLIP
Threaded hole position appoints ordinary or secure fixation type (through hole) of glass panels. That is why the insert element permits abovementioned types of installation.
77
MULTIFUNCTIONAL CLIP
77
78
AYPC.115.0110 NEW CLIP and AYPC.115.0120 INSERT
Color of insert elements is very close to silver color ofanodized profile A00-E6.
KEY FEATURES:
Metal threaded bush-insert guarantees reliable connection; Max glass height of 8 mm thickness is up to 2,5 m; Max glass height of 10, 12 mm thickness is up to 3 m; Material – glass-nylon composite New clips and insert preserve totally assemblage sequence, flexibility and reliability of ALT115 system
ALT115 SYSTEM APPORTUNITIES
79
Standard glass fixation
PVC-bush
Safe glass fixation
Description Code Article Name Colour
10301000AYPC.115.0011 Guide
0010301021 RAL9016103010806 A00-E610300600
AYPC.115.0001 Extruded aluminium
profile
0010300621 RAL9016103006806 A00-E6
ALT115 SYSTEM APPORTUNITIES
81
PLASTIC FITTINGS
AYPC.115.0904 – universalAYPC.115.0905 – special for glass of 10 mm thickness)
82
AYPC.115.0006 FRAME PROFILE
Frame permits to reduce the price for door unit by20%. Owing to frame it isn’t necessary forexpensive elements and special glass adjustment.
83
Levelling corners
Pin5x10DIN6325D
Insert corner
Methods of corner connection:- with pins- pressing method
AYPC.115.0006 FRAME COMPONENTS
84
Hardware groove permits to installthree types of sashes using ALT111hardware:- full glass sash;- aluminium sash;- wood sash.
JOINT SOLUTION - AYPC.115.0006
85
HARDWARE
KEY FEATURES OF HARDWARE:
clamping screws are twisted into steel threaded inserts; each hardware set is made with special equipment for assemblage; instructions for hardware installation are in the package; decorative cover cap is fixed reliably with fixator with a spring; decorative cover cap is made of anodized aluminium, color А00-Е6; hardware is used only with glass of 10 and 12 mm thickness; each hardware element is packed separately
86
Code Article Name Colour
103034806 ALT-5061S Lock with press-handle А00-Е6103035806 ALT-5061K2 Lock strike plate А00-Е6
ACCESSORIES
87
ACCESSORIES
88
ACCESSORIES
89
ACCESSORIES
90 90
PORTFOLIO
91 91
PORTFOLIO
92
PORTFOLIO
93 93
PORTFOLIO
LIGHT PARTITION SYSTEMALT118
APPLICATION AREA
Cloakroom
Shower cabins
Restrooms
95
SYSTEM APPORTUNITIES ALT 118
Module cabins with doors
96 96
ALT118 SYSTEM COMPONENTS Mullion
Framing profile
Corner connecting profile
Door profile
Top profile
97
98
Adjustable pin-bearing support
ALT118 SYSTEM COMPONENTS
98
Handle-button
Hinge with automatic return
Latch with indicator
99
ACCESSORIES FOR ALT118 SYSTEM
100
MARKETING SUPPORT
THANK YOU FOR ATTENTION!