aircraft propulsion-2
TRANSCRIPT
-
8/13/2019 Aircraft Propulsion-2
1/222
Unit-1
AIRCRAFT GAS TURBINES
Impulse and reaction blading of gas turbines Velocity triangles and power output Elementary
theory Vortex theory Choice of blade profile, pitch and chord Estimation of stage
performance Limiting factors in gas turbine design- Overall turbine performance Methods ofblade cooling Matching of turbine and compressor Numerical problems.
Axial and radial flow turbines
As with the compressor, there are two basic types of turbineradial flow and axial flow. The
vast majority of gas turbines employ the axial flow turbine.
The radial turbine can handle low mass flows more efficiently than the axial flow machine and
has been widely used in the cryogenic industry as a turbo-expander, and in turbochargers forreciprocating engines. Although for all but the lowest powers the axial flow turbine is normally
the more efficient, when mounted back-to-back with a centrifugal compressor the radial turbine
offers the benefit of a very short and rigid rotor. This configuration is eminently suitable for gas
turbines where compactness is more important than low fuel consumption. Auxiliary power units
for aircraft (APUs), generating sets of up to 3 MW, and mobile power plants are typical
applications.
Impulse and Reaction Turbine
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
2/222
Work can be extracted from a gas at a higher inlet pressure to the lower back pressure by
allowing it to flow through a turbine. In a turbine as the gas passes through, it expands. The work
done by the gas is equivalent to the change of its enthalpy.
It is a well known fact that the turbines operate on the momentum principle. Part of the energy of
the gas during expansion is converted into kinetic energy in the flow nozzles. The gas leavesthese stationary nozzles at a relatively higher velocity. Then it is made to impinge on the blades
over the turbine rotor or wheel. Momentum imparted to the blades turns the wheel. Thus, the two
primary parts of the turbine are,
(i) The stator nozzles, and
(ii) the turbine rotor blades.
Normally a turbine stage is classified as
(i) an impulsion stage, and
(ii) a reaction stage
An impulse stage is characterized by the expansion of the gas which occurs only in the stator
nozzles. The rotor blades act as directional vanes to deflect the direction of the flow. Further,
they convert the kinetic energy of the gas into work by changing the momentum of the gas more
or less at constant pressure.
A reaction stage is one in which expansion of the gas takes place both in the stator and in the
rotor.
The function of the stator is the same as that in the impulse stage, but the function in the
rotor is two fold.
(i) the rotor converts the kinetic energy of the gas into work, and
(ii) contributes a reaction force on the rotor blades.
The reaction force is due to the increase in the velocity of the gas relative to the blades. This
results from the expansion of the gas during its passage through the rotor.
A Single Impulse Stage
Impulse machines are those in which there is no change of static or pressure head of the fluid in
the rotor. The rotor blades cause only energy transfer and there is no energy transformation. The
energy transformation from pressure or static head to kinetic energy or vice versa takes place in
fixed blades only. As can be seen from the below figure that in the rotor blade passage of an
impulse turbine there is no acceleration of the fluid, i.e., there is no energy transformation.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
3/222
Hence, the chances are greater for separation due to boundary layer growth on the blade surface.
Due to this, the rotor blade passages of the impulse machine suffer greater losses giving lower
stage efficiencies.
The paddle wheel, Pelton wheel and Curtis stem turbine are some examples of impulse
machines.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
4/222
A Single Reaction Stage
The reaction stages are those, in which, changes in static or pressure head occur both in the rotor
and stator blade passages. Here, the energy transformation occurs both in fixed as well as
moving blades. The rotor experiences both energy transfer as well as energy transformation.
Therefore, reaction turbines are considered to be more efficient. This is mainly due to continuous
acceleration of flow with lower losses.
The degree of reactionof a turbomachine stage may be defined as the ratio of the static or
pressure head change occurring in the rotor to the total change across the stage.
Note: Axial-flow turbine with 50% reaction have symmetrical blades in their rotor and stators. It
may be noted that the velocity triangles at the entry and exit of a 50% reaction stage are also
symmetrical.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
5/222
Velocity Triangles of a Single Stage Machine
The flow geometry at the entry and exit of a turbomachine stage is described by the velocity
triangles at these stations. The velocity triangles for a turbomachine contain the following three
components.
1. The peripheral / whirl / tangential velocity (u) of a rotor blades2. The absolute velocity (c ) of the fluid and3. The relative velocity (w or v) of the fluid
These velocities are related by the following well-known vector equation.
This simple relation is frequently used and is very useful in drawing the velocity triangles
for turbomachines.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
6/222
The notation used here to draw velocity triangles correspond to the x-y coordinates; the
suffix (a or ) identifies components in the axial direction and suffix (t) refers to
tangential direction. Air angles in the absolute system are denoted by alpha (), where as
those in the relative system are represented by beta ().
Since the stage is axial, the change in the mean diameter between its entry and exit can be
neglected. Therefore, the peripheral or tangential velocity (u) remains constant in the velocity
triangles.
It can be proved from the geometry that
ct2 + ct3 = wt2+ wt3
It is often assumed that the axial velocity component remains constant through the stage. For
such condition,
ca= ca1= ca2= ca3
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
7/222
For constant axial velocity yields a useful relation,
tan 2+ tan 3= tan 2+ tan 3
Expression for Work Output
Though force and torque are exerted on both stationary and moving blades alike, work can only
be done on the moving rotor blades. Thus the rotor blades transfer energy from the fluid to the
shaft. The stage work in an axial turbine (u3= u2= u) can be written as,
W = u2ct2 u3ct3
= u{ct2- (-ct3)}
= u(ct2-ct3)
{Note: Usually this equation will be written with a minus sign between c t2and ct3. Whenever this
is written with a plus sign it is implied that ct3is negative}
This equation can also be expressed in another form,
+=
u
c
u
cuW tt 32
2
The first term
u
ct2 in the bracket depends on the nozzle or fixed angle (2) and the ratio
2c
u= . The contribution of the second term
u
ct3 to the work is generally small. It is also
observed that the kinetic energy of the fluid leaving the stage is greater for larger values of ct3.
The leaving loss from the stage is minimum when c t3 = 0, i.e., when the discharge from the stage
is axial (c3 = ca3). However, this condition gives lesser stage work as can be seen from the above
two equations.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
8/222
Blade loading and Flow coefficients
Performance of turbomachines are characterized by various dimensionless parameters. For
example, loading coefficient () and the flow coefficient () have been defined as,
u
c
u
W
a=
=
2
Since the work, W in the above equation is frequently referred to as the blade or stage work, the
coefficient, would also be known as the blade or stage loading coefficient.
For constant axial velocity (ca), it can be shown that
= (tan 2+ tan 3) = (tan 2+ tan 3)
The plots are useful in comparing the performances of various stages of different sizes and
geometries.
Blade and Stage efficiencies
Even though the blade and stage work (outputs) are the same, the blade and the stage efficiencies
need not be equal. This is because the energy inputs to the rotor blades and the stage (fixed bladering plus the rotor) are different. The blade efficiency is also known as the utilization factor ( )
which is an index of the energy utilizing capability of the rotor blades. Thus,
= b
= Rotor blade work / Energy supplied to the rotor blades
= W / Erb
W = u2 ct2+ u3 ct3
( ) ( ) ( )223
3
2
3
2
2
2
3
2
22
1
2
1
2
1wwuucc ++=
The energy supplied to the rotor blades is the absolute kinetic energy in the jet at the entry plus
the kinetic energy change within the rotor blades.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
9/222
( ) ( )233
2
2
2
2
3
2
22
1
2
1
2
1uuwwcErb ++=
For axial machines, u = u2= u3
( ) ( )( )22
2
3
2
2
2
2
2
3
2
3
2
2
wwc
wwccb
+
+==
Maximum utilization factor for a single impulse stage.
2
2
32
2
1
)(
c
ccu tt +=
After rearranging the terms, we have
)sin(42
2 ==b
This shows that the utilization factor is a function of the blade-to-gas speed ratio and the nozzle
angle.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
10/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
11/222
The above Figures show the velocity triangles for one axial flow turbine stage and the
nomenclature employed. The gas enters the row of nozzle blades (These are also known as 'stator
blades' and 'nozzle guide vanes') with a static pressure and temperature, P1, T1and a velocity C1
is expanded to P2,T2and leaves with an increased velocity C2at an angle 2. The rotor blade inlet
angle will be chosen to suit the direction 2of the gas velocity V2relative to the blade at inlet.
2and V2are found by vectorial subtraction of the blade speed U from the absolute velocity C2.
After being deflected, and usually further expanded, in the rotor blade passages, the gas leaves at
P3, T3with relative velocity V3 at angle 3. Vectorial addition of U yields the magnitude and
direction of the gas velocity at exit from the stage, C3and 3. 3is known as the swirl angle.
dimensional effects.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
12/222
Vortex theory
It was pointed out earlier that the shape of the velocity triangles must vary from root to tip of the blade
because the blade speed U increases with radius. Another reason is that the whirl component in the flow
at outlet from the nozzles causes the static pressure and temperature to vary across the annulus. With a
uniform pressure at inlet, or at least with a much smaller variation because the whirl component is
smaller, it is clear that the pressure drop across the nozzle will vary giving rise to a corresponding
variation in efflux velocity C2. Twisted blading designed to take account of the changing gas angles is
called vortex blading.
It has been common steam turbine practice, except in low-pressure blading where the blades are
very long, to design on conditions at the mean diameter, keep the blade angles constant from root to tip,
and assume that no additional loss is incurred by the variation in incidence along the blade caused by the
changing gas angles. Comparative tests have been conducted by the earlier researchers on a single-stage
gas turbine of radius ratio 1-37, using in turn blades of constant angle and vortex blading. The results
showed that any improvement in efficiency obtained with vortex blading was within the margin of
experimental error. This contrasts with similar tests on a 6-stage axial compressor, by another researcher,
which showed a distinct improvement from the use of vortex blading. This was, however, not so
much an improvement in efficiency (of about 1-5 per cent) as in the delay of the onset of surging
which of course does not arise in accelerating flow. It appears, therefore, that steam turbine
designers have been correct in not applying vortex theory except when absolutely necessary at
the LP end. They have to consider the additional cost of twisted blades for the very large number
of rows of blading required, and they know that the Rankine cycle is relatively insensitive to
component losses. Conversely, it is not surprising that the gas turbine designer, struggling to
achieve the highest possible component efficiency, has consistently used some form of
vortex blading which it is felt intuitively must give a better performance however small.
Vortex theory has been outlined earlier by Cohen and others where it was shown that if
the elements of fluid are to be in radial equilibrium, an increase in static pressure from
root to tip is necessary whenever there is a whirl component of velocity.Figure 7.8 shows
(see below) why the gas turbine designer cannot talk of impulse or 50 per cent reaction stages.The proportion of the stage pressure or temperature drop which occurs in the rotor must increase
from root to tip. Although Fig. 7.8 refers to a single-stage turbine with axial inlet velocity and no
swirl at outlet, the whirl component at inlet and outlet of a repeating stage will be small
compared with CW2- the reaction will therefore still increase from root to tip, if somewhat less
markedly.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
13/222
Choice of blade profile, pitch and chord
The next step is to choose stator and rotor blade shapes which will accept the gas incident upon
the leading edge, and deflect the gas through the required angle with the minimum loss. An
overall blade loss coefficient Y (or A) must account for the following sources of friction loss.
(a) Profile lossassociated with boundary layer growth over the blade profile (including
separation loss under adverse conditions of extreme angles of incidence or high inlet
Mach number).
(b) Annulus lossassociated with boundary layer growth on the inner and outer walls of the
annulus.
(c) Secondary flow lossarising from secondary flows which are always present when a
wall boundary layer is turned through an angle by an adjacent curved surface.
(d) Tip clearance lossnear the rotor blade tip the gas does not follow the intended path,
fails to contribute its quota of work output, and interacts with the outer wall boundary
layer.
The profile loss coefficient Yp is measured directly in cascade tests similar to those described for
compressor blading. Losses (b) and (c) cannot easily be separated, and they are accounted for by
a secondary loss coefficient Ys.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
14/222
The tip clearance loss coefficient, which normally arises only for rotor blades, will be denoted by
Yk. Thus the total loss coefficient Y comprises the accurately measured two-dimensional loss Yp,
plus the three-dimensional loss (Ys+Yk) which must be deduced from turbine stage test results.
All that is necessary for our present purpose for finding the choice of blade profile is limited to
the knowledge of the sources of loss.
Figure 7.11 shows a conventional steam turbine blade profile constructed from circular arcs and
straight lines. Gas turbines have until recently used profiles closely resembling this, although
specified by aerofoil terminology.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
15/222
Note that the blade profile will be completely determined when (a) the pitch/width ratio (s/w) is
established, and (b) both the camber line angle ' and blade thickness/pitch ratio have been
calculated for various values of x between 0 and 1.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
16/222
Turbine Performance
The performance of turbine is limited principally by two factors: compressibility and
stress. Compressibility limits the mass flow that can pass through a given turbine and, stress
limits the wheel speed U. The work per stage depends on the square of the wheel speed.
However, the performance of the engine depends very strongly on the maximum temperature. Of
course, as the maximum temperature increases, the allowable stress level diminishes; hence in
the design of the engine there must be a compromise between maximum temperature and
maximum rotor tip speed U.
For given pressure ratio and adiabatic efficiency, the turbine work per unit mass is proportional
to the inlet stagnation temperature. Since, in addition, the turbine work in a jet or turboshaft
engine is commonly two or three times the useful energy output of the engine, a 1% increase in
turbine inlet temperature can produce a 2% or 3% increase in engine output. This considerable
advantage has supplied the incentive for the adoption of fairly elaborate methods for cooling the
turbine nozzle and rotor blades.
Estimation of stage performance
The last step in the process of arriving at the preliminary design of a turbine stage is to check
that the design is likely to result in values of nozzle loss coefficient and stage efficiency which
were assumed at the outset. If not, the design calculations may be repeated with more probable
values of loss coefficient and efficiency. When satisfactory agreement has been reached, the
final design may be laid out on the drawing board and accurate stressing calculations can be
performed. Before proceeding to describe a method of estimating the design point performanceof a stage, however, the main factors limiting the choice of design, which we have noted during
the course of the worked example, will be summarized. The reason we considered a turbine for a
turbojet engine was simply that we would thereby be working near those limits to keep size and
weight to a minimum. The designer of an industrial gas turbine has a somewhat easier task: he
will be using lower temperatures and stresses to obtain a longer working life, and this means
lower mean blade speeds, more stages, and much less stringentaerodynamic limitations. A power
turbine, not mechanically coupled to the gas generator, is another case where much less difficulty
will be encountered in arriving at a satisfactory solution. The choice of gear ratio between the
power turbine and driven component is normally at the disposal of the turbine designer, and thus
the rotational speed can be varied to suit the turbine, instead of the compressor as we have
assumed here.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
17/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
18/222
The cooled turbine
Figure 7.29 illustrates the methods of blade cooling that have received serious attention and
research effort. Apart from the use of spray cooling for thrust boosting in turbojet engines, the
liquid systems have not proved to be practicable. There are difficulties associated with
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
19/222
channelling the liquid to and from the bladeswhether as primary coolant for forced convection
or free convection open thermosyphon systems, or as secondary coolant for closed thermosyphon
systems. It is impossible to eliminate corrosion or the formation of deposits in open systems, and
very difficult to provide adequate secondary surface cooling area at the base of the blades for
closed systems. The only method used successfully in production engines has been internal,
forced convection, air cooling. With 1-5-2 per cent of the air mass flow used for cooling per
blade row, the blade temperature can be reduced by between 200 and 300 C. Using current
alloys, this permits turbine inlet temperatures of more than 1650 to be used. The blades are
either cast, using cores to form the cooling passages, or forged with holes of any desired shape
produced by electrochemical or laser drilling.
Figure 7.30 shows the type of turbine rotor blade introduced in the 1980s. The next step forward
is likely to be achieved by transpiration cooling, where the cooling air is forced through a porous
blade wall. This method is by far the most economical in cooling air, because not only does it
remove heat from the wall more uniformly, but the effusing layer of air insulates the outer
surface from the hot gas stream and so reduces the rate of heat transfer to the blade. Successful
application awaits further development of suitable porous materials and techniques of blade
manufacture. We are here speaking mainly of rotor blade cooling because this presents the most
difficult problem. Nevertheless it should not be forgotten that, with high gas temperatures,
oxidation becomes as significant a limiting factor as creep, and it is therefore equally important
to cool even relatively unstressed components such as nozzle blades and annulus walls.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
20/222
Figure 7.31 (a) illustrates the principal features of nozzle blade cooling. The air is introduced
in such a way as to provide jet impingement cooling of the inside surface of the very hot leading
edge. The spent air leaves through slots or holes in the blade surface (to provide some film
cooling) or in the trailing edge.
FIG. 7.31 (a) Turbine nozzle cooling [(b) courtesy Rolls-Royce]
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
21/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
22/222
Figure 7.35: Shows a typical temperature distribution at the mid-span of
a blade designed to operate with Tg= 1500 and T= 320 .
It may be noted that the final design calculation for a cooled blade will involve an estimation ofthe two-dimensional temperature distribution over the blade cross-section at several values of
l/L. Finite difference methods are used to solve the differential equations, and conduction within
the blade is taken into account. Figure 7.35 shows a typical temperature distribution at the mid-
span of a blade designed to operate with Tg= 1500 and = 320 . It emphasizes one of the
main problems of blade cooling, i.e. that of obtaining adequate cooling at the trailing edge.
Finally, an estimation will be made of the thermal stresses incurred with due allowance for
redistribution of stress by creep: with cooled blades the thermal stresses can dominate the gas
bending stresses and be comparable with the centrifugal tensile stresses.
Finally, mention must be made of an alternative approach to the high- temperature turbinetheuse of ceramic materials which obviates the need for elaborate cooling passages. Much effort has
been expended on the development of silicon nitride and silicon carbide materials for small
turbine rotors (both axial and radial) in which it would be difficult to incorporate cooling
passages. Adequate reliability and life are difficult to achieve, but demonstrator engines have
been ran for short periods. Ceramic rotor blades are being investigated for use in stationary gas
turbines for powers up to about 5 MW, and experimental trials are expected in the late 1990s.
The use of ceramic turbines in production engines, however, remains an elusive goal three
decades after optimistic forecasts about their introduction.
Blade Cooling
Blade cooling is the most effective way of maintaining high operating temperatures making use
of the available material. Blade cooling may be classified based on the cooling site as external
cooling and internal cooling. Another classification based on the cooling medium is liquid
cooling and air cooling.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
23/222
External Cooling
The external surface of the gas turbine blade is cooled by making use of compressed air from the
compressor.
Other methods of external cooling are film cooling and transpiration cooling.
Internal Cooling
Internal cooling of blades is achieved by passing air or liquid through internal cooling passages
from hub towards the blade tip. The cooling of the blades is achieved by conduction and
convection.
Hollow blades can also be manufactured with a core and internal cooling passage. Based on the
cooling medium employed, blade cooling may be classified into liquid cooling and air cooling.
Requirements for Efficient Blade CoolingIn a conventional cooled blade, cooling is obtained due to convection by passing cooling air
through internal passages within the blade. The success in obtaining the large reduction in metal
temperature at the expense of a small quantity of cooling flow is governed by the skill in
devising and machining the cooling passages. Because the internal cooling relies on the cooling
air scrubbing against the cooling surface, the internal surface area must be large and the velocity
of the cooling air must be high. This implies that the cross-sectional flow area of the passage
must be small.
The design of the blade internal geometry for cooling is more complex because of the various
aerodynamic, heat transfer, stress and mechanical design criteria that must be satisfied. The most
successful designs have incorporated radial passages through which cooling air passes, escaping
at the tip.
The radial flow turbine
In a radial flow turbine, gas flow with a high tangential velocity is directed inwards and leaves
the rotor with as small a whirl velocity as practicable near the axis of rotation. The result is that
the turbine looks very similar to the centrifugal compressor, but with a ring of nozzle vanesreplacing the diffuser vanes as in Fig. 7.37. Also, as shown there would normally be a diffuser at
the outlet to reduce the exhaust velocity to a negligible value.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
24/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
25/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
26/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
27/222
Turbine and Compressor Matching
The problem of matching turbine and compressor performance has great importance for jet
engines, which must operate under conditions involving large variations in thrust, inlet pressure,
and temperature, and flight Mach number. Matching the components of turbofan and turboprop
engines involves similar considerations and procedures.
Essentially the matching problem is simple, though the computation can be length. The
steady-state engine performance at each speed is determined by two conditions: continuity of
flow and a power balance. The turbine mass flow must be the sum of the compressor mass flow
and the fuel flow, minus compressor bleed flow. Also the power output of the turbine must be
equal to that demanded by the compressor.
In principle, the matching computations could proceed as follows:
1. Select operating speed2.
Assume turbine inlet temperature
3. Assume compressor pressure ratio4. Calculate compressor work per unit mass5. Calculate turbine pressure ratio required to produce this work6. Check to see if compressor mass flow plus fuel flow equals turbine mass flow; if not,
assume a new value of compressor pressure ratio and repeat steps 4, 5, and 6 until
continuity is satisfied.
7. Now calculate the pressure ratio across the jet nozzle from the pressure ratios across thediffuser, compressor, combustor, and turbine.
8. Calculate the area of jet nozzle outlet necessary to pass the turbine mass flow calculatedin step 6 with pressure ratio calculated in step 7 and the stagnation temperature
calculated. If the calculated area does not equal the actual exit area, assume a new value
of turbine inlet temperature (step-2) and repeat the entire procedure.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
28/222
The designer will try to match turbine and compressor so that the compressor is operating
near its peak efficiency through the entire range of operation, as shown in the below
figure, where the operating line (i.e., the locus of stead-state matching condition) runs
through the centers of the islands defined by the constant-efficiency lines.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
29/222
-
8/13/2019 Aircraft Propulsion-2
30/222
Problems
In a single-stage impulse turbine the nozzle discharges the fluid on to the blades at an angle of
650 to the axial direction and the fluid leaves the blades with an absolute velocity of 300 m/s at
an angle of 30
0
to the axial direction. If the blades have equal inlet and outlet angles and there isno axial thrust, estimate the blade angle, power produced per kg/s of the fluid and blade
efficiency.
Solution:
Since the axial thrust is zero,
Ca3 = Ca2 = Ca
w3 = w2
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
31/222
ca3 = ca2 = ca = ca3 x cos 3
= 300 x cos 30 = 259.8 m/s
c2= ca2/cos 2= 259.8/cos 65 = 614.7 m/s
u = ct2 wt2 = wt3 - ct3
c2 sin 2- ca2tan 2 = ca3tan 3 c3 sin 3
Since ca2 = ca3 = ca and 2 = 3 =
2catan = c2 sin 2 + c3 sin 3
tan = (614.7 x sin 65 + 300 x sin 30) / 2 x 259.8
= 1.3609
= 53.70
2 = 3= 53.70
u = c2 sin 2- ca2tan 2
= 614.7 x sin 65 259.8 x tan 53.7
= 203.43 m/s
ct2 = c2 sin 2
= 614.7 x sin 65
= 557.1 m/s
ct3 = c3 sin 3
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
32/222
= 300 x sin 30
= 150 m/s
WT = 203.43 x (557.1 + 150) x 10-3
= 144 kJ/kg
= u/c2 = 203.43 / 614.7 = 0.33
Blade efficiency = 4 (sin 2 - 2)
= 4 x (0.33 x sin 65 0.332) = 0.761
= 76.1 %
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
33/222
Aircraft Engine Performance Parameters
Uninstalled thrust of a jet engine (single inlet and single exhaust) is given by
Uninstalled thrust of a jet engine (single inlet and single exhaust) is given by
It is most desirable to expand the exhaust gas to the ambient pressure, which gives
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
34/222
In this case, the uninstalled thrust equation becomes,
The installed thrust T is equal to the uninstalled thrust F minus the inlet drag D inletand minus
nozzle drag Dnozzle , or
T = F Dinlet- Dnozzle
Problem:
An advanced fighter engine operating at Mach 0.8 and 10 km altitude has the following
unistalled performance data and uses a fuel with low heating value 42,800 kJ/kg:
Uninstalled thrust = 50 kN
Mass flow rate of air = 45 kg/sec
Mass flow rate of fuel = 2.65 kg/sec
Determine the specific thrust, thrust specific fuel consumption, exit velocity, thermal efficiency,
propulsive efficiency, and overall efficiency (assume exit pressure equal to ambient pressure).
Find the installed thrust when the total drag is equal to 10% of the uninstalled thrust.
Solution:
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
35/222
Fs = 50/45 = 1.1111kN/(kg/sec)
= 1111.1 m/s
TSFC = 2.65 / 50
= 0.053 (kg/sec)/kN
= 53 mg/N-sec
V0 = Moao
= 239. 6 m/sec
Using the above equation exit velocity,
Veis obtained as 1275.6 m/s
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
36/222
Power output of the engine = 37.475 x 106W
Power input to the engine through fuel = 113.42 x 106W
Propulsive power or Thrust Power = 50,000 x 239.6
Thermal efficiency = 37.475 x 106/ 113.42 x 106
= 33.04 %
Propulsive Efficiency = 50,000 x 239.6 / 37,475 x 106
= 31.97 %
Overall efficiency = 50,000 x 239.6 / 113.42 x 106
= 10.56 %
For additional numerical problems please refer the following books
1. Mathur, M., and Sharma, R.P., Gas Turbines and Jet and Rocket Propulsion,Standard Publishers, New Delhi, 1988.
2. Ganesan, V., Gas Turbines, Tata McGraw-Hill Publishing Company Limited,New Delhi. Second Edn. 2003.
Additional reading
1. Hill, P.G. & Peterson, C.R. Mechanics & Thermodynamics of Propulsion Addison Wesley Longman INC, 1999.
2. Cohen, H., Rogers, G.F.C. and Saravanamuttoo, H.I.H., Gas Turbine Theory, LongmanCo., ELBS Ed., 1989.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
37/222
Unit-2
RAMJET PROPULSION
Operating principle Sub critical, critical and supercritical operation Combustion in ramjet
engine Ramjet performance Sample ramjet design calculations Introduction to scramjet
Preliminary concepts in supersonic combustion Integral ram- rocket- Numerical problems.
Ramjets
Ramjets can be thought of as propulsive devices evolved out of turbojets. Ramjets operates well only at high speeds, typically between M = 2.0 and 4.0. The combustion mode being not very different from that of an afterburner, the specificfuel consumption is comparable to that of afterburner. The ramjet, unlike turbojet and turbofan does not produce any thrust at zero speed. Ramjets are mostly contemplated for use in military applications.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
38/222
SCRAM JET ENGINES
A scram jet engine is an engine that is much lighter than a conventional jet engine, canpropel an object at speeds of over 5000 miles per hour and has no moving parts.
If you could get it to work, the trip from London to Sydney would only take two hours! This technology would also be very useful to launch small satellites. The engine runs on oxygen, which it gets from the atmosphere, and a small amount of
hydrogen.
The engine would save a fantastic amount on the cost of fuel. This technology has been around since the 1950s but the problem is the motor will only
become efficient at five times the speed of sound or Mach 5.
Because of this the plane would need two engines, an engine capable of getting it toMach 5 and a Scram Jet.
A ramjet engine
A scramjet engine
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
39/222
A ramjet has no moving parts and achieves compression of intake air by the forwardspeed of the air vehicle.
Air entering the intake of a supersonic aircraft is slowed by aerodynamic diffusioncreated by the inlet and diffuser to velocities comparable to those in a turbojet augmenter.
The expansion of hot gases after fuel injection and combustion accelerates the exhaust airto a velocity higher than that at the inlet and creates positive push.
Scramjet is an acronym for Supersonic Combustion Ramjet. The scramjet differs from the ramjet is that combustion takes place at supersonic air
velocities through the engine.
It is mechanically simple, but vastly more complex aerodynamically than a jet engine. Hydrogen is normally the fuel used. A scramjet (supersonic combustion ramjet) is a variation of a ramjet with the key
difference being that the flow in the combustor is supersonic.
At higher speeds it is necessary to combust supersonically to maximize the efficiency ofthe combustion process.
Projections for the top speed of a scramjet engine (without additional oxidizer input) varybetween Mach 12 and Mach 24 (orbital velocity), but the X-30 research gave Mach 17
due to combustion rate issues.
By way of contrast, the fastest conventional air-breathing, manned vehicles, such as theU.S. Air Force SR-71, achieve slightly more than Mach 3.2 and rockets achieved Mach
30+ during Apollo.
Like a ramjet, a scramjet essentially consists of a constricted tube through whichinlet air is compressed by the high speed of the vehicle, fuel is combusted, and then
the exhaust jet leaves at higher speed than the inlet air.
Also like a ramjet, there are few or no moving parts. In particular there is no high speedturbine as in a turbofan or turbojet engine that can be a major point of failure.
A scramjet requires supersonic airflow through the engine, thus, similar to a ramjet,scramjets have a minimum functional speed. This speed is uncertain due to the low
number of working scramjets, relative youth of the field, and the largely classified nature
of research using complete scramjet engines.
However it is likely to be at least Mach 5 for a pure scramjet, with higher Mach numbers7-9 more likely. Thus scramjets require acceleration to hypersonic speed via other means.
A hybrid ramjet/scramjet would have a lower minimum functional Mach number, andsome sources indicate the NASA X-43A research vehicle is a hybrid design.
Recent tests of prototypes have used a booster rocket to obtain the necessary velocity. Air breathing engines should have significantly better specific impulse while within
the atmosphere than rocket engines.
However scramjets have weight and complexity issues that must be considered. Whilevery short suborbital scramjets test flights have been successfully performed, perhaps
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
40/222
significantly no flown scramjet has ever been successfully designed to survive a flight
test.
The viability of scramjet vehicles is hotly contested in aerospace and space vehiclecircles, in part because many of the parameters which would eventually define the
efficiency of such a vehicle remain uncertain.
This has led to grandiose claims from both sides, which have been intensified by the largeamount of funding involved in any hypersonic testing. Some notable aerospace gurus
such as Henry Spencer and Jim Oberg have gone so far as calling orbital scramjets 'the
hardest way to reach orbit', or even 'scramjets' due to the extreme technical challenges
involved.
Major, well funded projects, like the X-30 were cancelled before producing any workinghardware.
The scramjet is a proposed solution to both of these problems, by modifications of theramjet design. The main change is that the blockage inside the engine is reduced, so that
the air isn't slowed down as much. This means that the air is cooler, so that the fuel canburn properly. Unfortunately the higher speed of the air means that the fuel has to mix
and burn in a very short time, which is difficult to achieve.
To keep the combustion of the fuel going at the same rate, the pressure and temperaturein the engine need to be kept constant. Unfortunately, the blockages which were removed
from the ramjet were useful to control the air in the engine, and so the scramjet is forced
to fly at a particular speed for each altitude. This is called a "constant dynamic pressure
path" because the wind that the scramjet feels in its face is constant, making the scramjet
fly faster at higher altitude and slower at lower altitude.
The inside of a very simple scramjet would look like two kitchen funnels attached bytheir small ends. The first funnel is the intake, and the air is pushed through, becomingcompressed and hot. In the small section, where the two funnels join, fuel is added, and
the combustion makes the gas become even hotter and more compressed. Finally, the
second funnel is a nozzle, like the nozzle of a rocket, and thrust is produced.
Note that most artists' impressions of scramjet-powered vehicle designs depict waveriderswhere the underside of the vehicle forms the intake and nozzle of the engine. This means
that the intake and nozzle of the engine are asymmetric and contribute directly to the lift
of the aircraft. A waverider is the required form for a hypersonic lifting body
A scramjet is a type of engine which is designed to operate at the high speeds normallyassociated with rocket propulsion.
It differs from a classic rocket by using air collected from the atmosphere to burn its fuel,as opposed to an oxidizer carried with the vehicle.
Normal jet engines and ramjet engines also use air collected from the atmosphere in thisway.
The problem is that collecting air from the atmosphere causes drag, which increasesquickly as the speed increases.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
41/222
Also, at high speed, the air collected becomes so hot that the fuel no longer burnsproperly.
Theory
All scramjet engines have fuel injectors, a combustion chamber, a thrust nozzle and aninlet, which compresses the incoming air.
Sometimes engines also include a region which acts as a flame holder, although the highstagnation temperatures mean that an area of focused waves may be used, rather than a
discrete engine part as seen in turbine engines.
Other engines use pyrophoric fuel additives, such as silane, to avoid such issues. An isolator between the inlet and combustion chamber is often included to improve the
homogeneity of the flow in the combustor and to extend the operating range of the
engine.
A scramjet is reminiscent of a ramjet.
In a typical ramjet, the supersonic inflow of the engine is decelerated at the inlet tosubsonic speeds and then reaccelerated through a nozzle to supersonic speeds to produce
thrust. This deceleration, which is produced by a normal shock, creates a total pressure
loss which limits the upper operating point of a ramjet engine.
For a scramjet, the kinetic energy of the freestream air entering the scramjet engine islarge compared to the energy released by the reaction of the oxygen content of the air
with a fuel (say hydrogen).
Thus the heat released from combustion at Mach 25 is around 10% of the total enthalpyof the working fluid.
Depending on the fuel, the kinetic energy of the air and the potential combustion heatrelease will be equal at around Mach 8.
Thus the design of a scramjet engine is as much about minimizing drag as maximizingthrust.
This high speed makes the control of the flow within the combustion chamber moredifficult. Since the flow is supersonic, no upstream influence propagates within the
freestream of the combustion chamber.
Thus throttling of the entrance to the thrust nozzle is not a usable control technique. In effect, a block of gas entering the combustion chamber must mix with fuel and have
sufficient time for initiation and reaction, all the while travelling supersonically through
the combustion chamber, before the burned gas is expanded through the thrust nozzle.
This places stringent requirements on the pressure and temperature of the flow, andrequires that the fuel injection and mixing be extremely efficient.
Usable dynamic pressures lie in the range 20 to 200 kPa (0.2-2 bar), where
whereqis the dynamic pressure of the gas
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
42/222
(rho) is the density of the gas
vis the velocity of the gas
Fuel injection and management is also potentially complex. One possibility would be that the fuel is pressurized to 100 bar by a turbo pump, heated
by the fuselage, sent through the turbine and accelerated to higher speeds than the air by a
nozzle.
The air and fuel stream are crossed in a comb like structure, which generates a largeinterface.
Turbulence due to the higher speed of the fuel lead to additional mixing. Complex fuelslike kerosine need a long engine to complete combustion.
The minimum Mach number at which a scramjet can operate is limited by the fact thatthe compressed flow must be hot enough to burn the fuel, and of high enough pressure
that the reaction is finished before the air moves out the back of the engine.
Additionally, in order to be called a scramjet, the compressed flow must still besupersonic after combustion.
Here two limits must be observed: Firstly, since when a supersonic flow is compressed it slows down, the level of
compression must be low enough (or the initial speed high enough) not to slow down the
gas below Mach 1.
If the gas within a scramjet goes below Mach 1 the engine will "choke", transitioning tosubsonic flow in the combustion chamber.
This effect is well known amongst experimenters on scramjets since the waves caused bychoking are easily observable.
Additionally, the sudden increase in pressure and temperature in the engine can lead to anacceleration of the combustion, leading to the combustion chamber exploding.
Secondly, the heating of the gas by combustion causes the speed of sound in the gasto increase (and the Mach number to decrease) even though the gas is still traveling
at the same speed. Forcing the speed of air flow in the combustion chamber under
Mach 1 in this way is called "thermal choking".
It is clear that a pure scramjet can operate at Mach numbers of 6-8, but in the lowerlimit, it depends on the definition of a scramjet.
Certainly there are designs where a ramjet transforms into a scramjet over the Mach 3-6range (Dual-mode scramjets). In this range however, the engine is still receiving
significant thrust from subsonic combustion of "ramjet" type.
The high cost of flight testing and the unavailability of ground facilities have hinderedscramjet development.
A large amount of the experimental work on scramjets has been undertaken in cryogenicfacilities, direct-connect tests, or burners, each of which simulates one aspect of the
engine operation.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
43/222
Further, vitiated facilities, storage heated facilities, arc facilities and the various types ofshock tunnels each have limitations which have prevented perfect simulation of scramjet
operation.
The HyShot flight test showed the relevance of the 1:1 simulation of conditions in the T4and HEG shock tunnels, despite having cold models and a short test time.
The NASA-CIAM tests provided similar verification for CIAM's C-16 V/K facility andthe Hyper-X project is expected to provide similar verification for the Langley AHSTF ,
CHSTF and 8 ft HTT.
Computational fluid dynamics has only recently reached a position to make reasonablecomputations in solving scramjet operation problems.
Boundary layer modeling, turbulent mixing, two-phase flow, flow separation, and real-gas aerothermodynamics continue to be problems on the cutting edge of CFD.
Additionally, the modeling of kinetic-limited combustion with very fast-reacting speciessuch as hydrogen makes severe demands on computing resources.
Reaction schemes are numerically stiff, having typical times as low as 10-19 seconds,requiring reduced reaction schemes.
Much of scramjet experimentation remains classified. Several groups including the USNavy with the SCRAM engine between 1968-1974, and the Hyper-X program with the
X-43A have claimed successful demonstrations of scramjet technology. Since these
results have not been published openly, they remain unverified and a final design method
of scramjet engines still does not exist.
The final application of a scramjet engine is likely to be in conjunction with engineswhich can operate outside the scramjet's operating range.
Dual-mode scramjets combine subsonic combustion with supersonic combustion foroperation at lower speeds, and rocket-based combined cycle (RBCC) engines supplementa traditional rocket's propulsion with a scramjet, allowing for additional oxidizer to be
added to the scramjet flow.
RBCCs offer a possibility to extend a scramjet's operating range to higher speeds orlower intake dynamic pressures than would otherwise be possible.
Advantages and disadvantages of scramjets
Special cooling and materials
Unlike a rocket that quickly passes mostly vertically through the atmosphere or a turbojetor ramjet that flies at much lower speeds, a hypersonic airbreathing vehicle optimally
flies a "depressed trajectory", staying within the atmosphere at hypersonic speeds.
Because scramjets have only mediocre thrust-to-weight ratios, acceleration would belimited. Therefore time in the atmosphere at hypersonic speed would be considerable,
possibly 15-30 minutes.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
44/222
Similar to a reentering space vehicle, heat insulation from atmospheric friction would bea formidable task. The time in the atmosphere would be greater than that for a typical
space capsule, but less than that of the space shuttle.
Therefore studies often plan on "active cooling", where coolant circulating throughout thevehicle skin prevents it from disintegrating from the fiery atmospheric friction.
Active cooling could require more weight and complexity. There is also safety concernsince it's an active system.
Often, however, the coolant is the fuel itself, much in the same way that modern rocketsuse their own fuel and oxidizer as coolant for their engines.
Both scramjets and conventional rockets are at risk in the event of a cooling failure. Half an engine
The typical waverider scramjet concept involves, effectively, only half an engine. Theshockwave of the vehicle itself compresses the inlet gasses, forming the first half of theengine. Likewise, only fuel (the light component) needs tankage, pumps, etc. This greatly
reduces craft mass and construction effort, but the resultant engine is still very much
heavier than an equivalent rocket or conventional turbojet engine of similar thrust.
Simplicity of design
Scramjets have few to no moving parts. Most of their body consists of continuoussurfaces. With simple fuel pumps, reduced total components, and the reentry system
being the craft itself, scramjet development tends to be more of a materials and modelling
problem than anything else.
Additional propulsion requirements
A scramjet cannot produce efficient thrust unless boosted to high speed, around Mach 5,depending on design, although, as mentioned earlier, it could act as a ramjet at low
speeds. A horizontal take-off aircraft would need conventional turbofan or rocket engines
to take off, sufficiently large to move a heavy craft. Also needed would be fuel for those
engines, plus all engine associated mounting structure and control systems. Turbofan
engines are heavy and cannot easily exceed about Mach 2-3, so another propulsion
method would be needed to reach scramjet operating speed. That could be ramjets or
rockets. Those would also need their own separate fuel supply, structure, and systems.
Many proposals instead call for a first stage of droppable solid rocket boosters, which
greatly simplifies the design.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
45/222
Pulsejet is a constant volume combustion device which is quite efficient only at low speeds and
uses unsteady combustion for its operation. Once the system is started, it works by taking in air
and fuel and combustion them during a part of the cycle and exhausting it during the next part of
the cycle. In order to promote and sustain the operation, a flapper device of metal or plastic, in
recent times, is used in front end.
Super sonic diffuser may be divided into two separate parts: the supersonic inlet and the
subsonic diffuser. Although this division is a convenient one, it must be remembered that the
phenomena in the supersonic and subsonic parts of the diffuser can, and often do, interact.
It should be remembered that the higher the Mach number, the greater will be our percentage
loss in pressure across a normal shock. Thus, at very high mach numbers, there is an appreciable
difference between (1) isentropic compression through out and (2) compression with a normal
shock.
The limitations imposed by the losses associated with a normal shock at higher Mach numbers
stimulated the development of a modified simple inlet design which incorporates a spike or
wedge in the nose section of the diffuser.
The modified design utilizes the spike or wedge to produce an oblique shock at the nose
section, and, the mach number after an oblique shock are greater than one. Consequently, in
addition to the oblique shock, we have a normal shock near the minimum area section. The
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
46/222
compression after the normal shock is of the standard subsonic diffuser type; that is, an increase
in area decreases the velocity.
It might be asked why a diffuser which has two shock waves, namely, an oblique and a normal
shock, would give better results than a simple inlet which has only one normal shock. The reason
for this is that the losses across a series of weak shock are less than the losses across one orseveral strong shocks. This means that the losses across the normal shock which follows the
oblique shock are considerably less than the losses across a normal shock in the free stream.
Increasing the number of oblique shocks before the normal shock reduces the losses through
the shock system. It must be noted that the complexity of the inlet also increases as the number
shocks increases. In addition to the number of shocks, the pressure losses are also function of the
shock arrangement. It may be noted that the maximum total pressure recovery occurs when the
total pressure recovery is the same across each of oblique shocks, and very nearly equal to that
across the final normal shock.
The three basic modes operation frequently referred to are subcritical operation, critical
operation, and supercritical operation. All these three inlets are operated at the design Mach
number, MD, which by definition, means that the conical shock or conical shock extended will
intersect the cowl lip.
At the subcritical operation, the normal shock is external and subsonic velocities exit atthe cowl.
For this condition mass-flow ratio based on capture area is less than one; spillageexists; the inlet is not swallowing air at maximum capacity; pressure recovery is low
since some of the air goes through a single, near normal shock; inlet drag is high
because of the intense shock; operation is generally unstable and conducive to acondition called buzz (normal shock moves in and out of the inlet at relatively high
frequencies). An important instability that occurs during the subcritical operation of
most supersonic inlets. This phenomenon, known as buzz, consists of a rapidoscillation of the inlet shock and flow pattern; the resultant internal disturbance is very
detrimental to engine performance. In a ramjet, for instance, the onset of buzz usually
extinguishes combustion. Although the pulses of the shock system are similar, the
interval between pulses is not constant; hence buzz cannot be considered a periodic
phenomenon. Although it is not thoroughly understood, buzz has been shown to be afunction of conditions only at , and immediately downstream of, the inlet.
In general subcritical operation is unsatisfactory and should be avoided. As the flow resistance downstream of the diffuser is increased, the mass-flow ratio can
be reduced to its limit value of 0 at which point no flow exits.
For critical operation, both maximum mass flow and ram recovery are attained for thedesign Mach number; thus condition represents the optimum performance condition. It
has the disadvantage, however, of being, marginally unstable in actual applications
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
47/222
because small changes in angles of attack or yaw or boundary layer separation can
induce the critical mode of operation across the threshold into the subcritical regime.Consequently, for actual operation it is usually better to operate the inlet in a more
stable condition, the supercritical regime.
The three basic modes operation frequently referred to aircraft inlets are subcritical operation,
critical operation, and supercritical operation, which are shown schematically for a typical case
in the above figure. With entirely diverging internal flow such as this, the normal shock position
is determined by a downstream flow restriction rather than by the inlet geometry. Hence
operating mode is sensitive to variations in exhaust-nozzle area and fuel flow rate. Subcritical
operation entails spilling of flow and a normal shock upstream of the inlet. Low and high
subcritical operations differ only in the extent of spilling. Supercritical operation occurs at the
same mass flow as critical operation, but with increased losses, since the normal shock occurs at
a higher Mach number. All these three inlets are operated at the design Mach number, MD, which
by definition, means that the conical shock or conical shock extended will intersect the cowl lip.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
48/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
49/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
50/222
The ramjet has the virtue of maximum simplicity, with no need for turbomachinery, and
maximum tolerance to high-temperature operation and minimum mass-per-unit thrust at suitable
flight Mach numbers. The ramjet also has its limitations. As well as being generally incapable of
steady operation at subsonic Mach numbers, it has an upper Mach number limit. For the
conventional ramjet (in which the supersonic inlet air is slowed to subsonic speeds to provide
stable combustion prior to the nozzle expansion), there is a limiting Mach number of about 6,
above which the temperature of the air entering the combustor is so high that combustion cannot
be completed. Most of the chemical energy of combustion is nonusefully transformed intodissociation reactions that on expansion do not provide the exhaust velocity needed for
satisfactory ramjet performance. To avoid this problem, substantial research has been, and is still
being, focused on the supersonic combustion ramjet (SCRAMJET). The difference between this
and the conventional ramjet is that combustion is to take place in a supersonic stream. Fuel must
be injected into the supersonic stream (without causing disruptive shock waves) and must mix
and burn in a millisecond or so. Conventional fuels do not ignite quickly enough, and gaseous
hydrogen seems the most likely candidate. Design of the fuel injector is a formidable challenge;
so is the problem of cooling a vehicle designed to operate at Mach numbers of 4 or higher.
Hydrogen could conceivably serve for structural cooling as well as for engine fuel.
It will be clear from this discussion that future designs for supersonic (or even hypersonic)
aircraft must cope with the design challenges of a whole range of flight Mach numbers.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
51/222
Supersonic Combustion
The losses associated with subsonic ramjet combustion can be substantial. If ramjets are to be
applied to hypersonic flight, additional problems arise because of extremely high temperature at
the entrance to the combustion chamber. This not only makes vehicle cooling very difficult, but
it leads to severe combustion loss due to dissociation.
Figure shows the air temperature reached after adiabatic deceleration from a high-altitude
ambient temperature of 220 K and from flight Mach number M to a chamber pressure of either 1
or 10 atm. For hypersonic flight (e.g. for M > 8) the temperature of the air in the chamber is quite
dependent on the pressure: The higher the pressure, the less dissociation and the higher the
temperature of the mixture. The temperature of the combustion products is likewise pressure
dependent.
Figure shows, for a combustion pressure of 10 atm and a flight Mach number of 10, there
is no temperature rise due to combustion; all of the combustion energy is absorbed bydissociation. One sees from the above Figure, the strange result that, at sufficiently high Mach
number, the temperature of the combustion products can be lower than that of the incoming air.
Consideration of the speed with which the fuel and air can be converted into dissociation
products may show that there is sufficient residence time in the combustion chamber to approach
equilibrium composition. But during the subsequent expansion in the nozzle, one cannot take
equilibrium composition for granted. It is quite possible that the expansion will be too rapid for
the composition to readjust, after each step of temperature and pressure reduction, to a new
equilibrium composition. If the expansion extremely rapid, the mixture may be effectively
frozen with the initial (high-temperature) composition. This would mean that little of the
combustion energy of the fuel (for the M = 10 case) would be available for acceleration of the
combustion products to produce thrust. The chemical kinetics of the recombination processes in
the nozzle would, in general, have a strong effect on the thrust and the propulsion efficiency of
the engine.
Some researchers have proposed the concept of the supersonic combustion as a way to avoid
this dissociation loss as well as the stagnation pressure losses associated with deceleration in
supersonic-to-subsonic inlets. With supersonic combustion, fluid temperatures are relatively low,
and this decreases the dissociation loss because dissociation depends on static rather than
stagnation temperature. Wall heat transfer, in contrast, depends essentially on stagnation
temperature, so the wall-cooling problem is not removed by employing supersonic combustion.
The stagnation pressure loss due to supersonic heating depends on the extent to which the fluid is
being accelerated while combustion is taking place.
The use of supersonic combustion requires fuel to be injected into, and mixed with, a
supersonic stream without excessive shock losses.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
52/222
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
53/222
The main advantages of the ramjet engine are;
1. High temperature can be employed2. In the absence of rotating machinery its construction is very simple and cheap3. It can operate effectively at high supersonic Mach numbers4. It is not very sensitive to the quality of fuel5. It provides high thrust per unit weight and frontal area
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
54/222
Ramjet engines Main disadvantages are;
1. It requires a launching device at supersonic speed2. It is unsuitable for subsonic flight3. It has low thermal efficiency and high TSFC4. Its maximum operating altitude is limited
Ideal Efficiency
Various process occurring in the ramjet engine can be represented by an open circuit Brayton
cycle. This cycle is considered here with the following assumptions:
1. Steady one-dimensional flow2. Isentropic compression and expansion, s = 0, P0 = 03. Perfect gas4. Constant pressure heat addition in the combustion chamber, P2 = P35. Very low Mach number in the combustion chamber.
P2 P02 P03
T2 T02 T03
Compression and expansion process here are thermodynamically different from turbo jetengine. These process here experience only energy transformation; there is no energy
transfer such as compressor and turbine work within the engine. Thrust work is obtained
from the energy supplied in the fuel during process 2-3. Heat is rejected during process 4-
1 outside the engine. However, the ideal efficiency of the ramjet engine is still given by
Equation,
( )
/1
11
11
==
rt
i
Here, the temperature ratio, with the above assumption is given by
2
1
01
1
02
1
2
2
11 iM
T
T
T
T
T
Tt
+====
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
55/222
Substituting the value of t from the above Equation to the previous equation we get,
2
1
2
1
2
12
11
2
1
211
11
M
M
Mi
+
=
+
=
)(1
1
21
11
2
1
Mf
M
i =
+
=
Though the actual thermal efficiency of the ramjet engine will be much lower than the
value given by the above equation it demonstrates an important characteristic i.e., the
efficiency increases with the flight Mach number and has a high value (76.19 % at M 1=
4) at higher operating Mach numbers.
Other performance parameters and efficiencies defined for air-breathing engines are also
applicable for the ram jet engine.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
56/222
The thermal efficiency or the Air standard Efficiency of the ideal cycle 1-2s-3-4s is given by,
= work / heat supplied
= 1 Qr/Qs
= 1 (T4s T1)/(T3-T2s)
The pressure ratio in the compressor and turbine is same,
i.e., r = P2/P1= P3/P4
Therefore the corresponding temperature ratios are given by,
/)1(
4
3
/)1(
1
2/)1(
4
3
1
2
=
====
P
P
P
Pr
T
T
T
Tt
s
s
( )
/1
11
11
==
rtAS
. A ramjet engine operates at M = 1.5 at an altitude of 6500 m. The diameter of theinlet diffuser at entry is 50 cm and the stagnation temperature at the nozzle entry is 1600
K. The calorific value of the fuel used is 40 MJ/kg. The properties of the combustion
gases are same as those of air (= 1.4, R = 287 J/kg K). The velocity of air at the diffuser
exit is negligible.
Calculate (a) the efficiency of the ideal cycle (b) flight speed (c) air flow rate (d) diffuser
pressure ratio (e) fuel-air ratio (f) nozzle pressure ratio (g) nozzle jet Mach number (h)propulsive efficiency (i) and thrust. Assue the following values; D = 0.90, B= 0.98, j
= 0.96, stagnation pressure loss in the combustion chamber = 0.02P02.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
57/222
At Z = 6500 m the properties of air are
T1 = 245.90 K, p1 = 0.440 bar, a1 = 414.5 m/s
= 0.624 kg/m3
(a)Ideal cycle efficiency
1
1
21
1
2
1M
i
+
=
= 0.310 Ans.
(b)M1= u/a1U = M1a1 = 1.5 x 314.5 = 471.75 m/s
Flight speed = 1698.3 kmph Ans.
( C) Area of cross section of the diffuser inlet
A1= d2/4 = 0.52/4 = 0.1963 m2
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
58/222
11uAma =
= 0.624 X 471.48 X 0.1963
Air flow rate = 57.752 kg/s Ans.
(d)For negligible velocity at the diffuser exit,P02= P2
2
1
/)1(
1
2
2
1
1
M
P
P
D
=
D= 0.9, M1= 1.5
P2/P1= 3.2875 Ans.
P2= 3.2875 x 0.44 = 1.446
(e) 45.1211 21
1
01=+= M
TT
= 1.45 x 245.9 = 356.55 K
ffBpa QmTTCm
= )( 0203
fBp
a
fQTTC
m
mf /)( 0203 ==
f = 1.005 (1600-356.55)/0.98 x 40000
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
59/222
-
8/13/2019 Aircraft Propulsion-2
60/222
Propulsive efficiency = 0.6693 Ans
(i)
umCmF
skgmmm
skgxm
a
fa
f
=
=+=+=
==
4
/593.59841.1752.57
/841.103188.0752.57
= (59.593 x 937.185 57.752 x 471.75) 10-3
Thrust = 28.614 kN Ans
Ram rocket
Air-augmented rockets (also known as rocket-ejector, ramrocket, ductedrocket, integral rocket/ramjets, or ejector ramjets) use the supersonic exhaust of some kind of
rocket engine to further compress air collected by ram effect during flight to use as additional
working mass, leading to greater effective thrust for any given amount of fuel than either the
rocket or a ramjet alone.
They represent a hybrid class of rocket/ramjet engines, similar to a ramjet, but able to give useful
thrust from zero speed, and are also able in some cases to operate outside the atmosphere, with
fuel efficiency not worse than both a comparable ramjet or rocket at every point.
Operation
A normal chemical rocket engine carries oxidizer and a fuel, sometimes pre-mixed, as in a solid
rocket, which are then burned. The heat generated greatly increases the temperature of the
mixture, which is then exhausted through a nozzle where it expands and cools. The exhaust is
directed rearward through the nozzle, thereby producing a thrust forward. In this conventionaldesign, the fuel/oxidizer mixture is both the working mass and energy source that accelerates it.
One method of increasing the overall performance of the system is to collect either the fuel or the
oxidizer during flight. Fuel is hard to come by in the atmosphere, but oxidizer in the form ofgaseous oxygen makes up 20% of the air and there are a number of designs that take advantage
of this fact. These sorts of systems have been explored in the LACE (liquid air cycle engine)
concept.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
61/222
Another idea is to collect the working mass instead. With an air-augmented rocket, an otherwise
conventional rocket engine is mounted in the center of a long tube, open at the front. As therocket moves through the atmosphere the air enters the front of the tube, where it is compressed
via the ram effect. As it travels down the tube it is further compressed and mixed with the fuel-
rich exhaust from the rocket engine, which heats the air much as a combustor would in a ramjet.
In this way a fairly small rocket can be used to accelerate a much larger working mass thannormally, leading to significantly higher thrust within the atmosphere.
A liquid air cycle engine (LACE) is a spacecraft propulsion engine that attempts to gain
efficiency by gathering part of its oxidizer from the atmosphere. In a LOX/LH2 bipropellant
rocket the liquid oxygen needed for combustion is the majority of the weight of the spacecraft onlift-off, so if some of this can be collected from the air on the way, it might dramatically lower
the take-off weight of the spacecraft.
Principle of operation
LACE works by compressing and then quickly liquefying the air. Compression is achievedthrough the ram-air effect in an intake similar to that found on a high-speed aircraft like
Concorde, where intake ramps create shock waves that compress the air. The LACE design thenblows the compressed air over a heat exchanger, in which the liquid hydrogen fuel is flowing.
This rapidly cools the air, and the various constituents quickly liquefy. By careful mechanical
arrangement the liquid oxygen can be removed from the other parts of the air, notably water,nitrogen and carbon dioxide, at which point it can be fed into the engine as normal. The
hydrogen is so much lighter than oxygen that the now-warm hydrogen is often dumped
overboard instead of being re-used as fuel, at a net gain.
One issue with the LACE system is that in order to appreciably reduce the mass of the oxygen
carried at launch, a LACE vehicle needs to spend more time in the lower atmosphere where itcan collect enough oxygen to supply the engines. This leads to greatly increased vehicle heating
and drag, which offset somewhat the savings in oxidizer weight, but this in turn is offset by
higher Isp (Specific impulse) permitting a lifting trajectory which greatly reduces gravity losses.More significantly the LACE system is far heavier than a rocket engine, and the performance of
launch vehicles of all types is particularly affected by dry mass, rather than any oxidizer mass
which would be burnt off over the course of the flight.
Additional Reading:
1. Hill, P.G. & Peterson, C.R. Mechanics & Thermodynamics of Propulsion Addison WesleyLongman INC, 1999.
2. Cohen, H., Rogers, G.F.C. and Saravanamuttoo, H.I.H., Gas Turbine Theory, Longman Co.,ELBS Ed., 1989.
3. Gorden, C.V., Aero thermodynamics of Gas Turbine and Rocket Propulsion, AIAA EducationSeries, New York, 1989.
4. Mathur, M., and Sharma, R.P., Gas Turbines and Jet and Rocket Propulsion, StandardPublishers, New Delhi, 1988.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
62/222
Unit-3
FUNDAMENTALS OF ROCKET PROPULSION
Operating principle Specific impulse of a rocket internal ballistics- Rocket nozzle
classification Rocket performance considerations Numerical Problems.
Rockets Special Features and Applications
Historical Reference The basic principles of all propulsive devices lie with the laws of motion due to Newton
(17th
Century AD). These laws are phenomenological and therefore one can expect that
even before Newton there may have existed many devices working on the principles of
reaction.
Rockets working directly on the principle of reaction are perhaps the simplest of thepropulsive engines.
The reciprocating engines and gas turbine engines are relatively more complex. The Chinese are credited with the invention of rockets probably in 12-14thcentury AD. Indians used the rockets as effective weapons in late 18 th century against British and in
19thcentury, the rockets became a part of the warfare in Europe. But it was only in the
early part of the present century that man has recognized the full potential of rocket
owing to the interests in space travel/satellite technology and like.
Tsiolkovsky (USSR 1903) Goddard (USA, 1912) and Oberth (1921) are the pioneers ofmodern rocketry.
The liquid propellant rocket owe their genesis to these people. The German V-2 rockets (25 tons, 65 sec, LOX-Alchol) and the post-second World war
progress in rocketry are too familiar to all.
Principle
All the conventional propulsion systems work by causing a change of momentum in a working
fluid in a direction opposite to the intended motion. Rockets fall under the category of direct
acting engines since the energy liberated by the chemical process is directly used to obtain
thrust. Being non-air breathing devices the basic component of a rocket are
(i) Combustion chamber where exothermic processes produces gases at high temperatureand pressure, and
(ii)Nozzle, which accelerate the fluid to high velocities and discharge them into surroundingatmosphere thereby deriving the desired force or thrust.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
63/222
Some Special Features
The non-air breathing nature of rockets makes them very distinct among the propulsive devices.
(a)The reaction system does not depend on the surrounding atmosphere. There are novelocity limitations and altitude ceiling.
(b)Since it has to carry its own oxidizer required for combustion reaction, the specificpropellant consumption is very high. Rockets consume approximately 15kg/kg-hr of
propellant compared to about 1 kg/kg-hr of fuel by turbojet engine.
(c)High pressure operation is possible and hence the ratio of energy liberation per unitvolume (and also unit weight of hardware) is very high.
(d)Main part of the rockets contains no moving element. Hence there is no constraint oninternal aerodynamics and the reliability is high. This also implies quick response times,
which makes them ideal control components.
With the above features, it is clear that the rockets are the most suitable power plants for
(i)
High altitude and space applications where atmospheric oxygen is not available,eg. Launch vehicles and satellite control rockets.
(ii) All applications where high thrust are required for short duration: missiles, boosters,JATO etc.
Rockets in Space Applications
There are a variety of rockets when it comes to launching and satellite control. Many of these are
non-chemical in nature but are restricted to extremely low thrust levels.
Sl
No Type
Order of
Magnitude ofThrust (N) F/W OperationalTime
Isp
(sec) Applications
1
Solar sail
(not a rocket in
fact)
10-5
10-4
Years Satellite Altitude
control
2
Electric Prop.
(Electro thermal,
Electro Static,
Electro
Magnetic)
10-6 - 10-2 10-5-10-3 Years 150 - 6000
Satellite control,
stabilization, orbit
maneuver
3Stored cold gas
(N2, NH3etc.)10-2 - 10-1 ~ 10-3 Years 50 - 100 -do-
4 Nuclear Rocket upto 105 20-30 Minute tohours 800 Interplanetary andspace travel
5
Chemical Rocket
(Solid, Liquid
and Hybrid)
upto 107 upto 80Seconds to
minutes@150-450
Launch vehicles,
Missiles, Control
rockets, Sounding
rockets, JATO etc
@ shuttle main engine operate for about 8 min at a time but over 7 hrs cumulatively.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
64/222
Classification of Chemical Rockets
Depending on the context, the chemical rockets are classified in many ways as follows:
(a)Type of propellant: Solid, Liquid (mono propellant / bipropellant and hybrid rockets)(b)Application: Launch vehicle, ABMs, JATOs, ICBM, IRBM, SAM etc.(c)Size of Unit (and thrust level sometimes): 10 ton, 100 kg etc.(d)Type of subsystem: Turbopump fed, clustering, grain type etc.
Specific Impulse
The specific impulse of a rocket,Isp, is the ratio of the thrust to the flow rate of the weight ejected,that is
where Fis thrust, is the rate of mass flow, and gis the acceleration of gravity at ground
level.
Specific impulse is expressed in seconds. When the thrust and the flow rate remain constantthroughout the burning of the propellant, the specific impulse is the time for which the rocket
engine provides a thrust equal to the weight of the propellant consumed.
For a given engine, the specific impulse has different values on the ground and in the vacuum ofspace because the ambient pressure is involved in the expression for the thrust. It is therefore
important to state whether specific impulse is the value at sea level or in a vacuum.
There are a number of losses within a rocket engine, the main ones being related to theinefficiency of the chemical reaction (combustion) process, losses due to the nozzle, and losses
due to the pumps.
Overall, the losses affect the efficiency of the specific impulse. This is the ratio of the realspecific impulse (at sea level, or in a vacuum) and the theoretical specific impulse obtained with
an ideal nozzle from gases coming from a complete chemical reaction. Calculated values of
specific impulse are several percent higher than those attained in practice.
From Equation (2.8) we can substitute C for Fin Equation (2.23), thus obtaining
Equation (2.24) is very useful when solving Equations (2.18) through (2.21). It is rare we aregiven the value of Cdirectly, however rocket engine specific impulse is a commonly given
parameter.
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
65/222
Internal Ballistics
The parameters that govern the burning rate and mass discharge rate of rocket motors are called
internal ballistic properties; they include
r propellant burning rate (velocity of consumption), m/sec or mm/sec or in/sec.
K ratio of burning surface to throat area, Ab/At
p temperature sensitivity of burning rate, expressed as percent change of burning
rate per degree change in propellant temperature at a particular value of chamber
pressure.
K- temperature sensitivity of pressure expressed as percent change of chamber
pressure per degree change in propellant temperature at a particular value of K,
and the influences caused by pressure, propellant ingredients, gas velocity, or acceleration.
The subsequent solid propellant rocket parameters are performance parameters; they include
thrust, ideal exhaust velocity, specific impulse, propellant mass fraction, flame temperature,
temperature limits and duration.
Propellant Burning Rate
The rocket motors operation and design depend on the combustion characteristics of the
propellant, its burning rate, burning surface, and grain geometry. The branch of applied science
describing these is known as internal ballistics.
Solid propellant burns normal to its surface. The (average) burning rate, r, is defined as theregression of the burning surface per unit time. For a given propellant, the burning rate is mainly
dependent on the pressure, p, and the initial temperature, Ti, of the propellant. Burning rate is
also a function of propellant composition. For composite propellants it can be increased by
changing the propellant characteristics:
1. Add a burning rate catalyst, often called burning rate modifier (0.1 to 3.0% of propellant)or increase percentage of existing catalyst.
2. Decrease the oxidizer particle size.3. Increase oxidizer percentage4. Increase the heat of combustion of the binder and/or the plasticizer5. Imbed wires or metal staples in the propellant
www.Vidyarthiplus.com
www.Vidyarthiplus.com
-
8/13/2019 Aircraft Propulsion-2
66/222
Apart from the propellant formulation and propellant manufacturing process, burning ratein a
full-scale motor can be increased by the following
1. Combustion chamber pressure2. Initial temperature of the solid propellant prior to start3. Combustion gas temperature4. Velocity of the gas flow parallel to the burning surface5. Motor motion ( acceleration and spin-induced grain stress)
Burning rate data are usually obtained in three ways namely, from testing by:
1. Standard strand burners, often called Crawford burners2. Small-scale ballistic evaluation motors3. Full-scale motors with good instrumentation
A strand burner is a small pressure vessal (usually with windows) in which a thin strand
or bar of propellant is ignited at one end and burned to the other end. The strand can be
inhibited with an external coating so that it will burn only on the exposed cross-sectionalsurface; chamber pressure is simulated by pressurizing the container with inert gas. The
burning rate can be measured by electric signals from embedded wires, by ultrasonic
waves, or by optical means. The burning rate measured on strand burners is usually lower
than that obtained from actual rocket motor firing (by 4 to 12%) because it does not truly
simulate the hot chamber environment of an actual rocket motor. Also small ballistic
evaluation motors usually have a slightly lower burning rate than full-scale large motors,
because of scaling factors.
During development of a new or modified solid propellant, it is tested extensively or
characterized. This includes the testing of the burn rate (in several different ways) underdifferent temperatures, pressures, impurities, and conditions. It also requires
measurements of physical, chemical, and manufacturing properties, ignitability, aging,
sensitivity to various energy inputs or stimuli (e.g., shock, friction, fires), moister
absorption, c