air conditioning - toyota service informationbdd59f94-c062-4b8a...this manual has been published to...

INS

IDE

EN

GIN

E C

OM

PA

RT

ME

NT

TOYOTA

ENGLISH

AIR CONDITIONING

EUROPE,GENERAL,AUSTRALIA

© 2001 DENSO CORPORATION

All Rights Reserved. This book may not be reproduced or copied,

in whole or in part, without the written permission of the publisher.

INTRODUCTIONIMPORTANT NOTICE

DEFINITION OF TERMS

FOREWORDThis manual has been published to explain how to install the air conditioning for TOYOTA COROLLA. When installing the air conditioning, installation should be performed as described in this manual.

[APPLICATION VEHICLE]

CAUTION

[DOCUMENT CODE AND DOCUMENT PART NUMBER]

This manual has been designed for technicians who are qualified and educated in the proper procedures of vehicle safety, handling and maintenance; experienced in installation of car air conditioning or who are able to carry out installation procedures when given instructions by an experienced technician in a supervisory capacity; and are certified to handling refrigerant. 1. Take special care to ensure that clearance between air conditioning components and other components such as

brake parts, fuel system and electric wires as specified in this manual.2. If a problem is found with the air conditioning system due to installation, refer back to the manual to correct the

problem(s).3. Vehicle and air conditioning kit components as well as installation procedures are subject to change without

prior notice. Refer to the latest installation manual and service information. Any changes affecting the above items will be given in the form of a “Installation instructions for air conditioning (Supplement)” (issued by DENSO) or a service bulletin (issued by the manufacturer).

WARNING : Describes precautions that should be observed in order to prevent injury or death to the user during installation.

CAUTION : Describes precautions that should be observed in order to prevent damage to the vehicle or its components, which may occur during installation if insufficient care is taken.

NOTE : Provides additional information that facilitates installation work.

FRONT,REARLEFT,RIGHT

: Shows the direction when viewed from the driver’s seat.

VEHICLE NAME MODEL CODE PRODUCTION PERIOD ENGINE TYPE STEERING POSITION

COROLLA NZE12#R 2000.8~ 1NZ/2NZ-FE RHD

ZZE12#R 1ZZ/3ZZ/4ZZ-FE,2ZZ-GE

1. Carefully read the separate manual "GENERAL INFORMATION/AFTER INSTALLATION" before and after installation.

2. Refer to the separate manual "INSTALLATION MANUAL (INSIDE PASSENGER COMPARTMENT)" for details on installation for the passenger compartment side.

MANUAL NAME DOCUMENT CODE DOCUMENT PART NUMBER

GENERAL INFORMATION /AFTER INSTALLATION

AOAMC-01* 988963-475*

INSTALLATION MANUAL(INSIDE PASSENGER COMPARTMENT)

AAAMB-24* 988963-455*

- 1

005001

VEHICLE HARNESS

BATTERY

Disconnect the negative cable first.

AC1895

ENGINE COVER

AC3568

1ZZ-FE E/G MODEL ONLY

1. INSTALLATION INSIDE PASSENGER COMPARTMENT

CAUTION

1. Before starting installation, remove the negative cable from the battery.

2. Before making any hoses and tubes connections, apply a few drops of compressor oil to the seat of O-ring and coupling nuts.

3. When tightening and loosening the fittings, use two wrenches for support.

4. Ensure fender covers are in position.5. Start the work from the inside passenger

compartment side.

CAUTION

First remove the negative terminal on the battery and the vehicle harness connection before installing the equipment.

(1) REMOVAL OF ORIGINAL PARTS
� 1ZZ-FE E/G MODEL ONLY [(a)](a) Engine cover
-

07

- 2

005001

FRONT

AC4368

BATTERY

BATTERY TRAY

AC4369

VEHICLE HARNESS

AIR CLEANER BOX UPPER COVER

AIR CLEANER HOSE

VSV

FRONT

AIR CLEANER BOXUPPER COVER

VSV

HOOK

AC4370

FRONT

AC4371

FILTER

(b) Battery and battery tray

(c) Disconnect the vehicle harness from the air
cleaner box upper cover.
(d) Disconnect the air cleaner hose from the air cleaner box upper cover.

(e) Temporarily remove the air cleaner box upper cover from the air cleaner lower cover.

(f) Temporarily remove the VSV from the air
cleaner box upper cover.
CAUTION

Do not disconnect the intake hoses from the VSV.

(g) Filter

-

07

- 3

005001

FRONT AC4372

VEHICLE HARNESS CLAMP

AC4373

AIR CLEANER BOX LOWER COVER

FRONT

FRONT

AC4374

AIR DUCT

FRONT GRILLE AC3569

RADIATOR UPPER SUPPORTS (RH,LH)

(h) Vehicle harness clamp

(i) Air cleaner box lower cover

(j) Air duct

(k) Radiator upper supports. (RH,LH)
(l) Front grille
-

07

- 4

005001

FRONT FENDER LINER (LH) SCREWS AC3570

CLIPS

AC4379

STEERING WHEEL

FRONT BUMPER

AC3571

SCREW

VEHICLE WITH SURGE TANK ONLY

AC3572 SURGE TANK


(m) Front fender liner (LH)

NOTETake care not to remove the front fender liner (LH)completely.

(n) Fully turn the steering wheel counterclockwise,
before removing the front fender liner (LH).
� VEHICLE WITH SURGE TANK ONLY [o)~(p)]
(o) Screw
(p) Surge tank

-

07

- 5

005001

SCREWSAC4381

UNDER COVER (RH)

CLIPS

CLIPS

CLIP

RESISTOR

BOLTS(M6 16)

AC4382

FRONT

AC4383

VEHICLE HARNESS(2-P)

TAPING

TO RESISTOR

RESISTOR


AC4384

(q) Under cover (RH)

(2) RESISTOR
(a) Install the resistor to the body using two bolts.
(b) Pull the vehicle harness (2-P) down.
(c) Route the vehicle harness (2-P) to the resistor.
(d) Connect the vehicle harness (2-P) to the
resistor.
-

07

- 6

005001

FRONT

FAN SHROUD AC4423

RADIATOR FAN MOTOR

VEHICLE HARNESS

VEHICLE HARNESS CLIP


FRONT

LIQUID TUBE No.1

RADIATOR

AC4385

FRONT

AC4386

LIQUID TUBE No.1

VEHICLE HARNESS

LIQUID TUBE No.1

AC4424

FRONT

(3) LIQUID TUBE(a) Disconnect the vehicle harness from the radiator

fan motor.(b) Temporarily remove the vehicle harness clip

from the fan shroud.

(c) Insert the liquid tube No.1 as shown in the left
figure.
(d) Route the liquid tube No.1 under the vehicle
harness, when inserting the liquid tube No.1.
(e) Set the liquid tube No.1 as shown in the left
figure.
-

07

- 7

005001

AC4420CONDENSER

COLLARS

BUSHINGS

RADIATOR

CORRUGATED BOARD AC4387

CONDENSER

CONDENSER

CONDENSER

AC4388

VIEWED FROM THE BOTTOM SIDE OF VEHICLE

VIHICLE HOLE

VIHICLE HOLE

RUBBER CUSHION

RUBBER CUSHION

(4) CONDENSER(a) Assemble two collars and two bushings to the

condenser.

(b) Lean the radiator backward then insert the
condenser in front of radiator.
CAUTION

Insert a corrugated board and others beforeinserting the condenser to prevent the radiator frombeing damaged.

(c) Make sure that the bushings of condenser

-

positively inserted into the vehicle holes.

07

- 8

005001

CONDENSER

AC4389

BOLTS (M8 32,SILVER)

FRONT

FAN SHROUD AC4425

RADIATOR FAN MOTOR

VEHICLE HARNESS



ADJUSTING BOLT

LOCK BOLTAC3573

ALTERNATOR BELT(DISCARD)

1NZ/2NZ-FE E/G MODEL ONLY

(d) Install the condenser using two bolts.

(e) Reinstall the vehicle harness clip to the fan
shroud.
(f) Reconnect the vehicle harness to the radiator fan motor.

(5) COMPRESSOR AND COMPRESSOR DRIVE
BELT� 1NZ/2NZ-FE E/G MODEL ONLY [(a)~(g)](a) Loosen the lock bolt and the adjusting bolt.(b) Remove and discard the alternator belt.
-

07

- 9

005001

(c) Install the compressor to the engine block using four bolts.

CAUTION

Tightening Torque

24.5 N•m (250 kgf•cm, 18.1 lbf•ft)

Tightening order; [1] » [2] » [3] » [4]

COMPRESSOR

ENGINE BLOCK

AC3574

BOLTS(M8 72)


[3]

[4]

[2]

[1]

-

07

- 10

005001


AC3575

COMPRESSOR DRIVE BELT

COMPRESSORPULLEY

WATER PUMPPULLEY

CRANKSHAFT PULLEY

ALTERNATOR PULLEY

10kgf

ROD

FRONT

ALTERNATOR

OCV

ALTERNATORADJUSTING BAR

COMPRESSOR DRIVEBELT

ADJUSTING BOLT

LOCK BOLT

AC3576


(d) Install the compressor drive belt to the pulleys as shown in the left figure.

CAUTION

(e) Adjust the belt tension as shown in the left figure.

CAUTION

1. The threads on the compressor belt must fit intogrooves on the pulley.

2. The belt tension must be measured betweenthe specified pulleys.

3. The tension may be measured between any

pulleys when using the DENSO belt tensiongauge.

4. Adjust the belt to the center of the range.5. Adjust the belt by tightening the adjusting bolt.

Belt deflection at 98 N•(10 kgf,22 lbf) force

Belt tension using the belt tension gauge

New Belt 7.0-8.5 mm(0.28-0.33 inch)

539-637 N(55-65 kgf, 121-143 lbf)

Used Belt (Re-adjustment)

11.0-13.0 mm(0.44-0.51 inch)

245-392 N(25-40 kgf, 55-88 lbf)

Insert the rod between the alternator adjusting bar and the engine mount bracket, and adjust the belt tension.Do not insert the rod between the alternator adjusting bar and OCV since the OCV might get damaged.

(f) Tighten the adjusting bolt.

(g) Tighten the lock bolt.

Tightening Torque

18.5 N•m (189 kgf•cm, 13.6 lbf•ft)

Tightening Torque

54 N•m (550 kgf•cm, 40 lbf•ft)

-

07

- 11

005001

NOTE

AC3577

FRONT

ALTERNATOR BELT(DISCARD)

1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY

FRONT

BOX-END COMBINATIONWRENCH (19mm)

� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL ONLY[(h)~(l)]

(h) Use the following procedure to remove the alternator belt.

NOTE

(i) Remove and discard the alternator belt.

Set the box-end combination wrench (19mm) as shown in the left figure, and remove the alternator belt to the pulleys while pulling the box-end combination wrench to the front of the vehicle.

-

07

- 12

005001

(j) Install the compressor to engine block using three bolts.

CAUTION

Tightening Torque

24.5 N•m (250 kgf•cm, 18.1 lbf•ft)

Tightening order; [1] » [2] » [3]

COMPRESSOR

ENGINE BLOCK

AC3579

BOLTS(M8 72)

[3]

[1]

[2]


-

07

- 13

005001

NOTE

FRONT

COMPRESSOR DRIVE BELT

AC3580


FRONT

BOX-END COMBINATIONWRENCH (19mm)

AC3578

TENSIONERPULLEY

P/S PUMP PULLEY ORIDLE PULLEY

ALTERNATOR PULLEY

WATER PUMPPULLEY

COMPRESSORPULLEYCRANKSHAFT PULLEY


TAPING

VEHICLE HARNESS (4-P)

FRONT

AC4394

(k) Use the following procedure to install the compressor drive belt.

NOTESet the box-end combination wrench (19mm) as shown in the left figure, and install the compressor drive belt to the pulleys while pulling the box-end combination wrench to the front of the vehicle.

(l) Install the compressor drive belt to the pulleys as
shown in the left figure.
(m) Pull the vehicle harness (4-P) down.

-

07

- 14

005001

FRONT


Mg/C CONNECTOR

AC4395COMPRESSOR

FRONT

AC4397

PLASTIC CLAMP No.2

(n) Connect the vehicle harness (4-P) to the Mg/C connector.

� PIPING LAYOUT

COMPRESSOR

CONDENSER

LIQUID TUBE No.1

PLASTIC CLAMP No.1

LIQUID TUBE No.2

PLASTIC CLAMP No.2

PLASTIC CLAMP No.3

DISCHARGE HOSE

SUCTION HOSE

BRACKET No.2

BRACKET No.1

FRONT

TO PASSENGER COMPARTMENT

AC4396

(6) PIPING
(a) Install the plastic clamp No.2 to the body.
-

07

- 15

005001

CONDENSER AC4421

LIQUID TUBE No.1

PLASTIC CLAMP No.1

BOLT(M6 25)

FRONT

AC4398

BOLT(M6 12)

BRACKET No.1

LIQUID TUBE No.2

AC4399PLASTIC CLAMP No.2 FRONT

LIQUID TUBE No.1

PACKING

PACKING

CROSSSECTION

QUICK JOINT (SMALL) AC4400

LIQUID TUBE No.2

BRACKET No.1

FRONT

(b) Assemble the plastic clamp No.1 to the condenser.

(c) Connect the liquid tube No.1 to the condenser using a bolt.

(d) Fasten the liquid tube No.1 to the plastic clamp No.1.

Tightening Torque

5.4 N•m (55 kgf•cm, 4.0 lbf•ft)

(e) Install the bracket No.1 to the body using a bolt.

(f) Connect the liquid tube No.2 to the liquid tube
No.1.
(g) Fasten the liquid tube No.1 to the plastic clamp No.2.

(h) Attach the packing around connecting portion of the liquid tube No.1 and liquid tube No.2.

(i) Route and connect the liquid tube No.2 to the
liquid and suction tube.
(j) Fasten the liquid tube No.2 to the bracket No.1.(k) Fasten the liquid tube No.2 using a quick joint

(small).

-

07

- 16

005001

BRACKET No.2

FRONT

AC4401

CAUTION

BOLT(M6 12)

AC4402

PLASTIC CLAMP No.3

FRONT

FRONT

SUCTION HOSE

AC4403COMPRESSOR BOLT(M6 35)

AC4404

SUCTION HOSE

NUT (M6)

FRONT

BRACKET No.2

(l) Install the bracket No.2 to the body using a bolt.

CAUTION

Catch the turning stopper to the vehicle holesurely.

(m) Install the plastic clamp No.3 to the body.

(n) Connect the suction hose to the compressor
using a bolt.
Tightening Torque

9.8 N•m (100 kgf•cm, 7.2 lbf•ft)

(o) Fasten the suction hose to the bracket No.2
using a nut.
-

07

- 17

005001

QUICK JOINT (BIG)

AC4405

SUCTION HOSE

FRONT

SUCTION HOSE

PLASTIC CLAMP No.3

AC3585

FRONT

DISCHARGE HOSE

DISCHARGE HOSE

AC4407

DISCHARGE HOSE

CONDENSER

FRONT

BOLT (M6 25)

(p) Connect the suction hose to the liquid and suction tube.

(q) Fasten the suction hose to the plastic clamp No.3.

(r) Fasten the suction hose using a quick joint (big).

(s) Insert the discharge hose as shown in the left
figure.
(t) Connect the discharge hose to the condenser
using a bolt.
Tightening Torque

5.4 N•m (55 kgf•cm, 4.0 lbf•ft)

-

07

- 18

005001

FRONTDISCHARGE HOSE AC3584

COMPRESSOR

BOLT(M6 35)

FRONT

TAPING

AC4409


AC4410


PRESSURE SWITCH

FRONT

RELAY BOX COVER

AC4411

(u) Connect the discharge hose to the compressor using a bolt.

Tightening Torque

9.8N•m (100 kgf•cm, 7.2 lbf•ft)

(v) Pull the vehicle harness (4-P) down.

(w) Connect the vehicle harness (4-P) to the
pressure switch.
(7) RELAYS
(a) Temporarily remove the relay box cover.
-

07

- 19

005001

FRONT

Mg/C RELAY (4-P,BLACK)

AC4412

FRONT

RELAY BOX COVER

AC4413

AC3581

CAUTION PLATE

SCREWSAC4381

UNDER COVER (RH)

CLIPS

CLIPS

CLIP

(b) Install the Mg/C relay into the relay box.

NOTEBe sure to install the relay box by supporting therelay box by hand from the bottom side to preventa contact defect.

(c) Reinstall the relay box cover.

(8) CAUTION PLATE
(a) Attach the caution plate to the frame.
NOTEAffix after completely wiping off dust and oil stainsfrom the frame.

(9) REINSTALLATION OF ORIGINAL PARTS
(a) Under cover (RH)
-

07

- 20

005001

AC3572 SURGE TANK


FRONT BUMPER

AC3571

SCREW


FRONT FENDER LINER (LH) SCREWS AC3570

CLIPS

FRONT GRILLE AC3582

RADIATOR UPPER SUPPORTS (RH,LH)

� VEHICLE WITH SURGE TANK ONLY [(b)~(c)](b) Surge tank

(c) Screw

(d) Front fender liner (LH)

(e) Radiator upper supports (RH,LH)
(f) Front grille
-

07

- 21

005001

FRONT

AC4374

AIR DUCT

AC4416

AIR CLEANER BOX LOWER COVER

FRONT

CAUTION

FRONT AC4417

VEHICLE HARNESS CLAMP

FRONT

AC4418

FILTER

(g) Air duct

(h) Air cleaner box lower cover

CAUTION

Make sure to be inserted the air duct into the aircleaner box lower cover.

(i) Vehicle harness clamp

(j) Filter

-

07

- 22

005001

VSV

FRONT

AIR CLEANER BOXUPPER COVER

VSV

HOOK

AC4419

AC4369

VEHICLE HARNESS

AIR CLEANER BOX UPPER COVER

AIR CLEANER HOSE

FRONT

AC4368

BATTERY

BATTERY TRAY

ENGINE COVER

AC3583

1ZZ-FE E/G MODEL ONLYRIB

(k) Reinstall the VSV to the air cleaner box upper cover.

(l) Air cleaner box upper cover
(m) Reconnect the vehicle harness to the air cleaner
box upper cover.(n) Reconnect the air cleaner hose to the air cleaner

box upper cover.

(o) Battery and battery tray

� 1ZZ-FE E/G MODEL ONLY [(p)]
(p) Engine cover
Tightening Torque

7.0 N•m (71 kgf•cm, 5.1 lbf•ft)

-

07

- 23 -

00500107

2. AFTER INSTALLATION

CAUTION

2-1.CHARGING REFRIGERANT (HFC-134a)

For additional information on charging refrigerant using the charging cylinder, refer to "GENERAL INFORMATION/AF-TER INSTALLATION: CHARGING REFRIGERANT (134a)".

CAUTION

2-2.RE-ADJUSTMENT OF COMPRESSOR BELT (1NZ/2NZ E/G MODEL ONLY)

To correct belt deflection caused by initial elongation, the air conditioning must be operated for at least 5 minutes before the final adjustment of the belt.

CAUTION

2-3.ADJUSTMENT OF ENGINE IDLING SPEED

CAUTION

Refer to the separate manual "GENERAL INFORMATION/AFTER INSTALLATION" for details on what to do after installation. (Document code: AOAMC-01*/Document part number: 988963-475*)

STANDARD AMOUNT OF REFRIGERANT 490 ± 30 g (1.08 ± 0.7 lbs)

Ensure to fill the refrigerant to the specified amount.

Belt deflection[at 98N(10kgf, 22lbf)force]

Belt tension[N (kgf, lbf)]

Vehicle equipped with 1NZ/2NZ E/G 11.0 - 13.0 mm(0.44 - 0.51 inch)

245 - 392 N(25 - 40 kgf, 55 - 88 lbf)

1. Excessive tension of belt may have an adverse effect on bearings, while excessive slackness can cause the belt to slip, make abnormal noise or shorten the belt life.

2. The belt deflection must be measured between the specified pulleys as indicated in this manual.3. The belt tension must be measured between the specified pulleys as indicated in this manual.4. The belt tension must be adjusted to the center of the specified belt tension range.

The engine revolution is controlled by a computer, therefore adjustment is not required. (when the air conditioning system is started, check whether idling revolution increases.)

3. AMPLIFIER� ALL EUROPEAN SPEC. AND 1NZ/2NZ-FE E/G MODEL (VEHICLE WITH HEATER)

- 24 -

00500107

� 1NZ/2NZ-FE E/G MODEL (VEHICLE WITHOUT HEATER)

- 25 -

00500107

� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITH HEATER AND GENERALLY SPEC.)

- 26 -

00500107

� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITHOUT HEATER AND GENERALLY SPEC.)

- 27 -

00500107

4. WIRING DIAGRAM� 1NZ/2NZ-FE E/G MODEL (VEHICLE WITH HEATER)

COMPRESSOR

MIDDLE EASTEXCEPT

Mg/CRELAY

IGRELAY

IG SW

12V

HEATERMAIN RELAY

BLOWERMOTOR

RH

LH

BLOWERRESISTOR

BLOWERRESISTOR

BLOWER SW RH A/C SW

TO RHEOSTAT

TO TAIL RELAY

AC3784

- 28 -

00500107

246108-404

ONLYMIDDLE EAST

COMPRESSOREFI ECUPRESSURE SW

A/C AMP

EVA.THERMISTOR

LH A/C SW

RESISTOR

FAN RELAY No.2

RADIATORFAN MOTOR

FAN RELAY No.1

AC3785

- 29 -

00500107

� 1NZ/2NZ-FE E/G MODEL (VEHICLE WITHOUT HEATER)

MIDOLE EASTEXCEPT

COMPRESSORMg/CRELAY

IGRELAY

IG SW

12V

HEATERMAIN RELAY

BLOWERMOTOR

RH

BLOWERRESISTOR

BLOWERRESISTOR

LH

BLOWER SW

TO GND

TO TAIL RELAY

VOLUME SW

AC3786

- 30 -

00500107

ONLYMIDDLE EAST

COMPRESSOREFI ECUPRESSURE SW

A/C AMP

EVA.THERMISTOR

RESISTOR

FAN RELAY No.2

RADIATORFAN MOTOR

FAN RELAY No.1

246108-406

AC3787

- 31 -

00500107

� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITH HEATER)

COMPRESSORMg/CRELAY

IGRELAY

IG SW

HEATERMAIN RELAY

BLOWERMOTOR

BLOWERRESISTOR

BLOWERRESISTOR

LH

RH

BLOWER SW A/C SW

TO GND

TO TAIL RELAY

12V

AC3788

- 32 -

00500107

246108-647

EFI ECUPRESSURE SW

A/C AMP

EVA.THERMISTOR

RESISTOR

FAN RELAY No.2

RADIATORFAN MOTOR

FAN RELAY No.1

AC3789

- 33 -

00500107

� 1ZZ/3ZZ/4ZZ-FE, 2ZZ-GE E/G MODEL (VEHICLE WITHOUT HEATER)

IGRELAY

IG SW

HEATERMAIN RELAY

BLOWERMOTOR

BLOWERRESISTOR

12V

RH

LH

BLOWERRESISTOR

BLOWER SW

VOLUME SW

TO GND

TO TAIL RELAY

Mg/CRELAY

COMPRESSOR

MIDDLE EASTEXCEPT

AC3790

- 34 -

00500107

A/C AMP

EVA.THERMISTOR

RESISTOR

PRESSURE SW EFI ECU

FAN RELAY No.1

RADIATORFAN MOTOR

FAN RELAY No.2

ONLYMIDDLE EAST

COMPRESSOR

246108-407

AC3791

- 35 -

00500107

� ALL EUROPEAN SPEC.

COMPRESSORMg/CRELAY

IGRELAY

IG SW

12V

HEATERMAIN RELAY

BLOWERMOTOR

BLOWERRESISTOR

BLOWERRESISTOR

LH

RH

BLOWER SW A/C SW

TO GND

TO TAIL RELAY

AC4498

- 36 -

00500107

246108-711

EFI ECUPRESSURE SW

A/C AMP

EVA.THERMISTOR

RESISTOR

FAN RELAY No.2

RADIATORFAN MOTOR

FAN RELAY No.1

AC4499

- 37 -

00500107

- 38 -

00500107

DENSO CORPORATION

SERVICE DEPARTMENT

Kariya, Aichi, Japan

Frist Issue : AUGUST 2000

Second Issue : SEPTEMBER 2001

Publication No. : AAAMB-25A

Printed in Japan

AAAMB-25A988963-4561

air conditioning - toyota service informationbdd59f94-c062-4b8a...this manual has been published to...

Documents