air conditioning system –
TRANSCRIPT
-
8/14/2019 Air Conditioning System
1/73
AIR CONDITIONING SYSTEM AIR CONDITIONING SYSTEM
AC1
-
8/14/2019 Air Conditioning System
2/73
PRECAUTIONS FOR SERVICING R134a AIRCONDITIONERS1. USE OF NEW REFRIGERANT R134a
The very different characteristics of refrigerantsR134a and R12 have determined the design of theirrespective air conditioning systems. Under no circum stances allow R12 to enter an R134a system, or viceversa, because serious damage could occur.
GENERAL DESCRIPTIONNEW AIR CONDITIONING SYSTEM WITHR134a
Refrigerant R12 (CFC12), previously used in automo biles air conditioning systems is believed to contribute
towards the depletion the earths ozone layer. Theozone layer help to protect us against the harmfulultraviolet rays of the sun.
2. USE OF PROPER COMPRESSOR OILCompressor oil used in conventional R12 air condi tioning systems cannot be used in R 134a air condi tioning systems.Always use genuine Toyota R1 34a air conditioning oilN D OIL 8, made expressly for use with R 1 34a.
If even a small amount of the wrong oil is changed, itwill result in clouding of the refrigerant.A large amount will cause the compressor to seize up.
A newly developed refrigerant, R134 a (HFC 134 a),does not the destroy the ozone layer.
AIR CONDITIONING SYSTEM GENERAL DESCRIPTIONAC2
-
8/14/2019 Air Conditioning System
3/73
4. TIGHTEN CONNECTING PARTS SECURELYSecurely tighten the connecting parts to prevent leak ing of refrigerant gas.Apply a few drops of compressor oil to 0ringfittings for easy tightening and to prevent leakingof refrigerant gas.CAUTION: Apply only NDOIL 8 compressor oilTighten the nuts using 2 wrenches to avoid twist
ing the tube.Tighten the 0ring fittings or the bolted typefittings to the specified torque.
5. INSERT PLUG IMMEDIATELY IN DISCONNECTEDPARTSInsert a plug immediately in the disconnected parts toprevent the ingress of moisture and dust.
6. DO NOT REMOVE PLUG FROM NEW PARTS UNTILIMMEDIATELY BEFORE INSTALLATION
3. USE OF PROPER O RINGS AND SEALS0rings and seals used for conventional R12 airconditioning systams cannot be used for R134a airconditioning systems.Always use genuine Toyota R 134a system 0ringsand seals for R 1 34a air conditioning systems.
7. DISCHARGE GAS IN NEW COMPRESSOR FROMCHARGING VALVE BEFORE INSTALLING ITIf the gas in the new compressor is not dischargedfirst, compressor oil will spray out with gas when theplug is removed.
If Orings and/or seals for R1 2 air conditioning sys tems are used by mistake in the connections of an R134a air conditioning system, the Oring and sealswill foam and swell resulting in leakage of refrigerant.
AIR CONDITIONING SYSTEM GENERAL DESCRIPTIONAC3
-
8/14/2019 Air Conditioning System
4/73
-
8/14/2019 Air Conditioning System
5/73
3. BE CAREFUL THAT LIQUID REFRIGERANT DOESNOT GET IN YOUR EYES OR ON YOUR SKINIf liquid refrigerant gets in your eyes or on your skin:
(a) Wash the area with lots of cool water.CAUTION: Do not rub your eyes or skin.
(b) Apply clean petroleum jelly to the skin.(c) GO immediately to a physician or hospital for profes
sional treatment.
HANDLING PRECAUTIONS FORREFRIGERANT CONTAINER1. NEVER HEAT CONTAINER OR EXPOSE IT TO
NAKED FLAME2. BE CAREFUL NOT TO DROP CONTAINER AND NOT
TO APPLY PHYSICAL SHOCKS TO IT
HANDLING PRECAUTIONS FORREFRIGERANT1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED
AREA OR NEAR AN OPEN FLAME2. ALWAYS WEAR EYE PROTECTION
CHARGING AND LEAKCHECK METHODSEvacuate the refrigeration system according to thefollowing procedures.
Fill refrigerant in gas state untilgauge pressure reads 1 kglcm2Abnormal indication of
manifold gauges
Check and correctpipe joints
RefrigerantCharge
RefrigerantCharge
StartEvacuation
StopEvacuation
Leave for 5 min.
Gas LeakCheck
AirtightCheck
10 min.
AIR CONDITIONING SYSTEM GENERAL DESCRIPTIONAC5
-
8/14/2019 Air Conditioning System
6/73
CAUTION: Be sure to connect both the high and low pressure
quickconnectors onto the A/C system when evacuating. If only one side is connected, the systemwould be open to atmosphere through the otherconnector, making it impossible to maintainvacuum.
Be sure to turn off the manifold gauge valve immediately after evacuating the system. Then you mayswitch off the vacuum pump.
PRECAUTIONS WHEN CHARGINGREFRIGERANT1. DO NOT OPERATE COMPRESSOR WITHOUT
ENOUGH REFRIGERANT IN REFRIGERANTSYSTEMIf there is not enough refrigerant in the refrigerant
system oil lubrication will be insufficient and compres sor burnout may occur, so take care to avoid this.2. DO NOT OPEN HIGH PRESSURE MANIFOLD VALVE
WHILST COMPRESSOR IS OPERATINGIf the high pressure valve is opened, refrigerant flowsin the reverse direction and could cause the chargingcylinder to rupture, so open and close the low pres sure valve only.
3. BE CAREFUL NOT TO OVERCHARGE WITH REFRIGERANT IN SYSTEMIf refrigerant is overcharged, it causes problems such
as insufficient cooling, poor fuel economy, engineoverheating etc.
ELECTRICAL PARTSBefore removing and inspecting the electrical parts,set the ignition switch to the LOCK position anddisconnect the negative () terminal cable from bat tery.CAUTION: Work must be started after 90 seconds fromthe time the Ignition switch is turned to the LOCKposition and the negative () terminal cable is disconnected from the battery.
AIR CONDITIONING SYSTEM GENERAL DESCRIPTIONAC6
-
8/14/2019 Air Conditioning System
7/73
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
Failure to carry out service operations in the correctsequence could cause the supplemental restraintsystem to deploy, possibly leading to a serious acci dent.
During removal or installation of the parts and theyellow wire harness and connector for the airbag isnecessary, refer to the precautionary notices in the RSsection before performing the operation.CAUTION: Work must be started after 90 seconds fromthe time the ignition switch is turned to the LOCKposition and the negative () terminal cable is disconnected from the battery.
AIR CONDITIONING SYSTEM GENERAL DESCRIPTIONAC7
-
8/14/2019 Air Conditioning System
8/73
DESCRIPTIONPARTS LOCATION
AIR CONDITIONING SYSTEM DESCRIPTIONAC8
-
8/14/2019 Air Conditioning System
9/73
AIR CONDITIONING SYSTEM DESCRIPTIONAC9
-
8/14/2019 Air Conditioning System
10/73
ELECTRICAL WIRING DIAGRAM(Lever Type On 5SFE Engine Model)
AIR CONDITIONING SYSTEM DESCRIPTIONAC10
-
8/14/2019 Air Conditioning System
11/73
AIR CONDITIONING SYSTEM DESCRIPTIONAC11
-
8/14/2019 Air Conditioning System
12/73
(Push Button Type On 5SFE Engine Model)
AIR CONDITIONING SYSTEM DESCRIPTIONAC12
-
8/14/2019 Air Conditioning System
13/73
AIR CONDITIONING SYSTEM DESCRIPTIONAC13
-
8/14/2019 Air Conditioning System
14/73
(Lever Type On 1 MZFE Engine Model)
AIR CONDITIONING SYSTEM DESCRIPTIONAC14
-
8/14/2019 Air Conditioning System
15/73
AIR CONDITIONING SYSTEM DESCRIPTIONAC15
-
8/14/2019 Air Conditioning System
16/73
(Push Button Type On 1 MZFE Engine Model)
AIR CONDITIONING SYSTEM DESCRIPTIONAC16
-
8/14/2019 Air Conditioning System
17/73
AIR CONDITIONING SYSTEM DESCRIPTIONAC17
-
8/14/2019 Air Conditioning System
18/73
DAMPERS POSITION
AIR CONDITIONING SYSTEM DESCRIPTIONAC18
-
8/14/2019 Air Conditioning System
19/73
PREPARATIONSST (SPECIAL SERVICE TOOLS)
(0711758070) TJoint
(0711778050) Refrigerant Charging Gauge
(0711758080) Quick Coupler
(0711788070) Refrigerant Charging Hose
(0711758090) Quick Coupler
(0711788060) Refrigerant Charging Hose
(0711788080) Refrigerant Charging Nose
(0711758060) Refrigerant Drain Service Valve
Suction (diam. 13 mm)
Discharge (diam. 16 mm)
Suction (Blue)
Discharge (Red)
Utility (Green)
0711638360 Gas Leak Detector Assembly
0711058060 Air Conditioner Service Tool Set
0711266040 Magnetic Clutch Remover
0711276060 Magnetic Clutch Stopper
0711484020 Snap Ring Pliers
AIR CONDITIONING SYSTEM PREPARATIONAC19
-
8/14/2019 Air Conditioning System
20/73
RECOMMENDED TOOL0908200050 TOYOTA Electrical Tester Set
When replacing compressor
When replacing evaporator
When replacing condenser
NDOIL 8 or equivalent
When replacing receiver
LUBRICANT
10 cc (0.34 fl.oz.)
140 cc (4.9 fl.oz.)
40 cc (1.4 fl.oz.)
40 cc (1.4 f I.oz.)
Compressor oil
ClassificationCapacityItem
AIR CONDITIONING SYSTEM PREPARATIONAC20
-
8/14/2019 Air Conditioning System
21/73
USE OF MANIFOLD GAUGE SETMANIFOLD GAUGE SET INSTALLATION1. CONNECT CHARGING HOSES TO MANIFOLD
GAUGE SETTighten the nuts by hand.CAUTION: Do not connect the wrong hoses.
2. CONNECT QUICK CONNECTORS TO CHARGINGHOSESTighten the nuts by hand.
3. CLOSE BOTH HAND VALVES OF MANIFOLDGAUGE SET
4. REMOVE CAPS FROM SERVICE VALVES ON REFRIGERANT LINE
MANIFOLD GAUGE SET REMOVAL1. CLOSE BOTH HAND VALVES OF MANIFOLD
GAUGE SET2. DISCONNECT QUICK CONNECTORS FROM SER
VICE VALVES ON REFRIGERANT LINEHINT: Slide the sleeve of the quick connector upwardto unlock the connector and remove it from the ser vice valve.
3. INSTALL CAPS TO SERVICE VALVES ON REFRIGERANT LINE
5. CONNECT QUICK CONNECTORS TO SERVICEVALVESHINT: Push the quick connector onto the servicevalve, then slide the sleeve of the quick connectordownward to lock it.
AIR CONDITIONING SYSTEM USE OF MANIFOLD GAUGE SETAC21
-
8/14/2019 Air Conditioning System
22/73
-
8/14/2019 Air Conditioning System
23/73
W i r i n g o r
W i r i n g
C o n n e c t
i o n
E x p a n s i o n
V a l v e
( R e p
l a c e
)
A / C C o n
t r o l A s s e m
b l y
A i r o u
t l e t
S e r v o m o t o r
C o n
d e n s e r
F a n
M o t o r
A i r I n l e t S e r v o m o t o r
M a g n e
t C l u t c h
B l o w e r
R e s
i s t o r
A / C A m p l
i f i e r
B l o w e r
M o t o r
C o m p r e s s o r
E v a p o r a
t o r
C o n
d e n s e r
R e c e i v e r
AC57 AC58 AC47AC67 AC49 AC45 AC53AC56 AC66AC55 AC36 AC36AC59
AIR CONDITIONING SYSTEM TROUBLESHOOTINGAC23
-
8/14/2019 Air Conditioning System
24/73
REFRIGERANT SYSTEM INSPECTION WITH MANIFOLD GAUGE SET
This is a method in which the trouble is located by using a manifold gauge set.(See USE OF MANIFOLD GAUGE SET on page AC21 )Read the manifold gauge pressure when the following conditions are established:(a) Temperature at the air inlet with the switch set at RECIRC is 30 35 _ C (86 95 _ F)
(b) Engine running at 1,500 rpm(c) Blower speed control switch set at high(d) Temperature control set at max. cool
HINT: It should be noted that the gauge indications may vary slightly due to ambient temperatureconditions.
1. NORMALLY FUNCTIONING REFRIGERATION SYSTEMGauge reading:
Low pressure side:0.15 0.25 MPa (1.5 2.5 kgf/cm)
High pressure side:1.37 1.57 MPa (14 16 kgf/emt)
AIR CONDITIONING SYSTEM TROUBLESHOOTINGAC24
-
8/14/2019 Air Conditioning System
25/73
(1) Check for gas leakagewith leak detector andrepair if necessary
(2) Charge refrigerant toproper arhount
(3) If pressure indicatedvalue is near 0 whenconnected to gauge,create the vacuum af ter inspecting and re pairing the location ofthe leak
Drier in oversaturatedstate
Moisture in refrigerationsystem freezes at expan sion valve orifice andblocks circulation of re frigerant
Moisture entered in re frigeration systemfreezes at expansionvalve orifice and tempo rarily stops cycle, butnormal state is restoredafter a time when the icemelts
(1) Replace receiver/drier(2) Remove moisture in
cycle through repeat edly evacuating air
(3) Charge new refrigerantto proper amount
Pressure low on bothlow and high pressuresides
Bubbles seen in sightglass continuously
Insufficient cooling per formance
During operation, prea sure on low pressureside sometimesbecomes a vacuumand sometimes normal
2. MOISTURE PRESENT IN REFRIGERATION SYSTEM
Insufficient refrigerant insystem1
Refrigerant leaking
Condition: Periodically cools and then fails to cool
Gas leakage at someplace in refrigeration sys tem
3. INSUFFICIENT REFRIGERANT
Symptom seen inrefrigeration system
Condition: Insufficient cooling
Symptom seen inrefrigeration system
Probable cause
Probable cause
Diagnosis
Diagnosis
Remedy
Remedy
AIR CONDITIONING SYSTEM TROUBLESHOOTINGAC25
-
8/14/2019 Air Conditioning System
26/73
(1) Check heat sensingtube, expansion valveand EPR
(2) Clean out dirt in expan sion valve by blowingwith airIf not able to removedirt, replace expansionvalve
(3) Replace receiver(4) Evacuate air and
charge new refrigerantto proper amount.For gas leakage from
heat sensing tube, re place expansion valve.
Refrigerant flow ob structed by moisture ordirt in refrigeration sys tem
Refrigerant flow ob structed by gas leakagefrom expansion valveheat sensing tube
Vacuum indicated onlow pressure side, verylow pressure indicatedon high pressure side
Frost or dew seen onpiping before and afterreceiver/drier or expan sion valve
Condition: Does not cool (Cools from time to time in some cases)
Pressure low on bothlow and high pressuresides
Frost on tubes from re-ceiver to unit
5. REFRIGERANT DOES NOT CIRCULATE
4. POOR CIRCULATION OF REFRIGERANT
Refrigerant flow ob structed by dirt in re ceiver
Refrigerant does not cir culate
Condition: Insufficient cooling
Symptom seen inrefrigeration system
Symptom seen inrefrigeration system
Diagnosis
R e c e i v e rclogged
Replace receiv-er
Probable cause
Probable cause
Diagnosis
Remedy
Remedy
AIR CONDITIONING SYSTEM TROUBLESHOOTINGAC26
-
8/14/2019 Air Conditioning System
27/73
(1) Clean condenser(2) Check fan motor oper ation
(3) If (1) and (2) are in nor mal state, checkamount of refrigerantCharge proper amountof refrigerant
Excessive refrigerant incycle refrigerant over charged:
Condenser cooling insuf ficient condenser finsclogged or fan motorfaulty
Pressure too high onboth low and highpressure sides
No air bubbles seenthrough the sight glasseven when the enginerpm is lowered.
6. REFRIGERANT OVERCHARGE OR INSUFFICIENT COOLING OF CONDENSER
Unable to develop suffi cient performance due toexcessive refrigerant insystem
.Insufficient cooling ofcondenser
Pressure too high onboth low and highpressure sides
The low pressure pipingis hot to the touch
Bubbles seen in sightglass
(1) Check compressor oilto see if dirty or insuffi cient
(2) Evacuate air andcharge new refrigerant
Air present in refrigera tion system
Insufficient vacuumpurging
7. AIR PRESENT IN REFRIGERATION SYSTEM
Condition: Does not cool down sufficiently
Condition: Does not cool sufficiently
Air entered in refrigera tion system
Symptom seen inrefrigeration system
Symptom seen inrefrigeration system
Probable cause
Probable cause
Diagnosis
Diagnosis
Remedy
Remedy
AIR CONDITIONING SYSTEM TROUBLESHOOTINGAC27
-
8/14/2019 Air Conditioning System
28/73
8. EXPANSION VALVE IMPROPERLYMOUNTED/HEAT SENSING TUBE DEFECTIVE(OPENS TOO WIDE)
Pressure too high onboth low and highpressure sides
Frost or large amountof dew on piping on lowpressure side
(1) Check heat sensingtube installed condition
(2) If (1) is normal, checkexpansion valveReplace if defective
Excessive refrigerant inlow pressure piping
Expansion valve openedtoo wide
Compression defective
Valve leaking or broken,sliding parts
Pressure too high onlow pressure side
Pressure too low onhigh pressure side
Trouble in expansionvalve or heat sensingtube not installed cor rectly
9. DEFECTIVE COMPRESSION COMPRESSOR
Internal leak in compres sor
Repair or replace com pressor
Condition: Insufficient cooling
Symptom seen inref rigeration system
Symptom seen inrefrigeration system
Condition: Does not cool
Probable cause
Probable cause
Diagnosis
Diagnosis Remedy
Remedy
AIR CONDITIONING SYSTEM TROUBLESHOOTINGAC28
-
8/14/2019 Air Conditioning System
29/73
REFRIGERANT VOLUMEREFRIGERANT VOLUME INSPECTION1. RUN ENGINE AT IDLE SPEED2. OPERATE A/C AT MAXIMUM COOLING FOR A
FEW MINUTES3. INSPECT AMOUNT OF REFRIGERANT
OBSERVE THE SIGHT GLASS ON THE LIQUID TUBE.
*: Bubbles in the sight glass with ambient temperatu ers higher can be considered normal if cooling issuff icient.
REFRIGERANT CHARGE VOLUMESpecified amount:
850 50 g (29.98 1.76 oz)
(1) Check for gas lakage with gas leaktester and repair if necessary
(2) Add refrigerant until bubbles dis apear
(1) Check for gas leakage with gas lea
ktester and repair if necessary(2) Add refrigerant until bubbles disap pear
(1) Discharge refrigrant(2)Evacuate air and charge proper amo
unto of purified refrigerant
Immediately after air conditioning isturned off, refrigerant in sight glassstays clear
When air conditioning is turned off, re frigerant foams and then stay clear
Temperature between compressor inletand outlet is noticeably different
No temperature difference betweencompressor inlet and outlet
No bubbles present in sight glass
Bubbles present insight glass
None, sufficient or too much
Empty or nearly empty
Amount of refrigerant
Refer to items 3 and 4
Refer to items 5 and 6Proper or too much
Too much
Insufficient
Symptom Remedy
Proper
Item
AIR CONDITIONING SYSTEM REFRIGERANT VOLUMEAC29
-
8/14/2019 Air Conditioning System
30/73
2. INSPECT DRIVE BELT TENSIONUsing a belt tension gauge, check the drive belt ten sion.Belt tension gauge:Nippondenso BTG20 (9550600020) orBorroughs No. BT3373FDrive belt tension:
5S FE:New belt 165 26 IbfUsed belt 110 11 lbf1 MZFE:New belt 165 26 lbfUsed belt 88 22 lbfHINT: New belt refers to a belt which has been used
less than 5 minutes on a running engine. Used belt refers to a belt which has beenused
on a running engine for 5 minutes or more. After installing the drive belt, check that it fits
properly in the ribbed grooves.
IDLEUP SPEEDIDLE UP SPEED INSPECTION1. WARM UP ENGINE2. INSPECT IDLE SPEED
5S FE:
DRIVE BELT TENSIONDRIVE BELT TENSION INSPECTION1. INSPECT DRIVE BELTS INSTALLATION CONDI
TIONCheck that the drive belt fits properly in the ribbedgrooves.
Standard idle speed (rpm)
Standard idle speed (rpm)Magnet clutch condition
Magnet clutch condition
Approx. 850
Approx. 750
Approx. 700
Approx. 700
1 MZ FE:
No engaged
No engaged
Engaged
Engaged
AIR CONDITIONING SYSTEM DRIVE BELT TENSIONAC30
-
8/14/2019 Air Conditioning System
31/73
ONVEHICLE INSPECTION1. INSPECTION HOSE AND TUBE CONNECTIONS FOR
LOOSENESS
2. INSPECT HOSES AND TUBES FOR LEAKAGEUsing a gas leak tester, check for leakage of refriger ant.
REFRIGERANT LINESTIGHTENING TORQUE OF REFRIGERATION LINES
AIR CONDITIONING SYSTEM REFRIGERANT LINESAC31
-
8/14/2019 Air Conditioning System
32/73
REFRIGERANT LINES REPLACEMENT1. DISCHARGE REFRIGERANT IN REFRIGERATION
SYSTEM(See page AC21 )
2. REPLACE FAULTY TUBE OR HOSEHINT: Cap the open fittings immediately to keep mois
ture or dirt out of the system.3. TORQUE CONNECTIONS TO SPECIFIED TORQUE
NOTICE: Connections should not be torque tighter thanthe specified torque.
4. EVACUATE AIR IN REFRIGERATION SYSTEM ANDCHARGE WITH REFRIGERANTSpecified amount:
850 50g (29.98 1.76 oz)5. INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak tester, check for leakage of refriger ant.
6. INSPECT AIR CONDITIONING OPERATION
AIR CONDITIONING SYSTEM REFRIGERANT LINESAC32
-
8/14/2019 Air Conditioning System
33/73
3. DISCONNECT WATER VALVE CONTROL CABLEFROM WATER VALVE
4. DISCONNECT WATER HOSES FROM HEATER RADIATOR PIPES
5. REMOVE INSTRUMENT PANEL AND REINFORCEMENT(See page BO108 )
6. REMOVE BLOWER UNIT(See page AC35 )
AIR CONDITIONING UNITA/C UNIT REMOVAL1. DISCHARGE REFRIGERANT FROM REFRIGERA
TION SYSTEM(See page AC21 )
2. DRAIN ENGINE COOLANT FROM RADIATORHINT: It is not necessary to drain out all the coolant.
7. DISCONNECT LIQUID AND SUCTION TUBE FROMBLOCK JOINTRemove 2 bolts and both tubes.
8. REMOVE REAR AIR DUCTSRemove the clip and the air duct.
9. REMOVE HEATER PROTECTORRemove the 2 clips and the heater protector.
AIR CONDITIONING SYSTEM AIR CONDITIONING UNITAC33
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
34/73
-
8/14/2019 Air Conditioning System
35/73
BLOWER UNIT INSTALLATION1. INSTALL BLOWER UNIT(a) Install the blower unit with the 3 screws and the nut.(b) Connect the air inlet damper control cable to the
blower unit.(c) Connect the connector.2. INSTALL CONNECTOR BRACKET3. INSTALL ECU BRACKET AND ECU
4. INSTALL GLOVE COMPARTMENT
BLOWER UNITBLOWER UNIT REMOVAL1. REMOVE GLOVE COMPARTMENT
(See page BO108 )2. REMOVE ECU AND ECU BRACKET
3. REMOVE CONNECTOR BRACKET(a) Disconnect the connector from the connector brack
et.(b) Remove the 2 screws and the bracket.
4. REMOVE BLOWER UNIT(a) Disconnect the connector from the blower unit.(b) Disconnect the air inlet damper control cable.(c) Remove the 3 screws, nut and the blower unit.
AIR CONDITIONING SYSTEM BLOWER UNITAC35
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
36/73
Compressor:1. INSTALL MANIFOLD GAUGE SET
(See page AC21 )2. START ENGINE3. INSPECT COMPRESSOR FOR METALLIC SOUND
Check that there is a metallic sound from the com pressor when the A/C switch is turn on.If metallic sound is heard, replace the compressor
assembly.4. INSPECT PRESSURE OF REFRIGERATION SYSTEMSee Refrigerant System Inspection with ManifoldGauge Set on page AC24 .
5. STOP ENGINE6. INSPECT VISUALLY FOR LEAKAGE OF REFRIGER
ANT FROM SAFETY SEALIf there is any leakage, replace the compressor assem bly.
COMPRESSORONVEHICLE INSPECTIONMagnet Clutch:1. MAKE THE FOLLOWING VISUAL CHECKS:
Leakage of grease from the clutch bearing.
Signs of oil on the pressure plate or rotor.Repair or replace, as necessary.2. INSPECT MAGNET CLUTCH BEARING FOR NOISE(a) Start engine.(b) Check for abnormal noise from near the compressor
when the A/C switch is OFF.If abnormal noise is being emitted, replace the mag netic clutch.
3. INSPECT MAGNET CLUTCH(a) Disconnect the connector from the magnet clutch.(b) Connect the positive (+) lead from the battery to the
terminal on the magnetic clutch connector and thenegative () lead to the body ground.
(c) Check that the magnet clutch is energized.If operation is not as specified, replace the magnetclutch.
AIR CONDITIONING SYSTEM COMPRESSORAC36
-
8/14/2019 Air Conditioning System
37/73
1. RUN ENGINE AT IDLE SPEED WITH A/C ON FORAPPROX 10 MINUTES
2. STOP ENGINE
3. DISCONNECT NEGATIVE () CABLE FROM BATTERYCAUTION: Work must be started after 90 seconds fromthe time the ignition switch is turned to the LOCKposition and the negative () terminal cable is disconnected from the battery.
4. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM(See page AC21 )
6. DISCONNECT DISCHARGE HOSE AND SUCTIONHOSE FROM COMPRESSOR
7. DISCONNECT CONNECTOR FROM MAGNETCLUTCH
8. REMOVE COMPRESSOR(a) Loosen the drive belt.(b) Remove 3 bolts and compressor.
COMPRESSOR REMOVAL5SFE Engine Model:
AIR CONDITIONING SYSTEM COMPRESSORAC37
-
8/14/2019 Air Conditioning System
38/73
1. RUN ENGINE AT IDLE SPEED WITH A/C ON FORAPPROX 10 MINUTES
2. STOP ENGINE3. DISCONNECT NEGATIVE () CABLE FROM BAT
TERYCAUTION: Work must be started after 90 seconds fromthe time the ignition switch is turned to the LOCKposition and the negative () terminal cable is disconnected from the battery.
COMPRESSOR REMOVAL1 MZFE Engine Model:
AIR CONDITIONING SYSTEM COMPRESSORAC38
-
8/14/2019 Air Conditioning System
39/73
4. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM(See page AC21 )
5. DISCONNECT DISCHARGE HOSE AND SUCTIONHOSE FROM COMPRESSOR
6. DISCONNECT CONNECTOR FROM MAGNETCLUTCH
7. REMOVE DRIVE BELTLoosen the pivot bolt and adjusting lock bolt andremove the drive belt.
8. REMOVE COMPRESSOR(a) Remove 2 nuts and 2 bolts.(b) Remove the compressor.
AIR CONDITIONING SYSTEM COMPRESSORAC39
-
8/14/2019 Air Conditioning System
40/73
1. REMOVE PRESSURE PLATE(a) Using SST and socket wrench, remove the shaft bolt.
SST 07112 76060
(b) Install a SST on the pressure plate.SST 0711266040
MAGNET CLUTCH DISASSEMBLY
AIR CONDITIONING SYSTEM COMPRESSORAC40
-
8/14/2019 Air Conditioning System
41/73
2. REMOVE ROTOR(a) Using SST, remove the snap ring.
SST 0711484020CAUTION: Do not spread the point of SST widely.Max width:
23.1 mm
3. REMOVE STARTER(a) Disconnect the stator lead wire from the compressor
housing.
(b) Using a plastic hammer, tap the rotor off the shaft.NOTICE: Be careful not to damage the pulley when tapping on the rotor.
(c) Using SST and socket wrench, remove the pressureplate.SST 0711276060
(d) Remove the shims from the pressure plate.
AIR CONDITIONING SYSTEM COMPRESSORAC41
-
8/14/2019 Air Conditioning System
42/73
MAGNET CLUTCH ASSEMBLY1. INSTALL STATOR(a) Install the stator on the compressor.
NOTICE: The snap ring should be installed so that itsbeveled side faces up.
(b) Using SST, install the new snap ring.SST 07114 84020
(b) Using a SST, remove the snap ring.SST 0711484020
(c) Remove the stator.
AIR CONDITIONING SYSTEM COMPRESSORAC42
-
8/14/2019 Air Conditioning System
43/73
2. INSTALL ROTOR(a) Install the rotor on the compressor shaft.(b) Using SST, install the new snap ring.
SST 0711484020CAUTION:Do not spread the point of SST widely.Max width:
23.1 mm
(c) Using SST and torque wrench, fasten the magnetclutch lead wire to the cylinder block.Torque: 3.4 Nm (35 kgf.cm, 30 in.lbf)SST 0711061050
(b) Using SST and torque wrench, install the shaft bolt.SST 0711276060Torque: 13 Nm (135 kgfcm, 10 ftlbf)
NOTICE: The snap ring should be installed so that itsbeveled side faces up.
3. INSTALL PRESSURE PLATE(a) Put the shims on the pressure plate.
AIR CONDITIONING SYSTEM COMPRESSORAC43
-
8/14/2019 Air Conditioning System
44/73
-
8/14/2019 Air Conditioning System
45/73
RECEIVERONVEHICLE INSPECTION
INSPECT FITTINGS FOR LEAKAGEUsing a gas leak tester, check for leakage.If there is leakage, check the tightening torque at the
joints.
RECEIVER REMOVAL1. DICHARGER REFRIGERANT FROM REFRIGERA
TION SYSTEM(See page AC21 )
3. REMOVE RECEIVER FROM RECEIVER HOLDERRemove the bolt, then remove the receiver from re ceiver holder.NOTICE: Cap the open fittings immediately to keeps moisture out of the system.
2. REMOVE 2 LIQUID TUBES FROM RECEIVERRemove the 2 bolts and the both tubes from thereceiver.
AIR CONDITIONING SYSTEM RECEIVERAC45
-
8/14/2019 Air Conditioning System
46/73
RECEIVER INSTALLATION1. INSTALL RECEIVER INTO RECEIVER HOLDER
Install the receiver into the receiver, holder with thebolt.
2. INSTALL 2 LIQUID TUBES TO RECEIVERInstall 2 liquid tubes to the receiver with 2 bolts.
Torque: 5.5 Nm (55 kgfcm, 48 in.lbf)NOTICE: Do not remove the caps until the tubes areconnected.
3. REPLENISH COMPRESSOR OIL IF RECEIVER HASBEEN REPLACEDAdd 15 cc (0.5 fl.oz.)Compressor oil:
ND OIL 8 or equivalent4. EVACUATE AIR IN REFRIGERATION SYSTEM AND
CHARGE WITH REFRIGERANTSpecified amount:
850 50 g (29.98 1.76 oz)5. INSPECT FOR LEAKAGE OF REFRIGERANT6. INSPECT A/C OPERATION
AIR CONDITIONING SYSTEM RECEIVERAC46
-
8/14/2019 Air Conditioning System
47/73
-
8/14/2019 Air Conditioning System
48/73
CONDENSER INSTALLATION1. INSTALL CONDENSER
Install the condenser with the 2 bolt.2. INSTALL LIQUID TUBES
Install both tubes with the 2 bolts.Specified torque: 9.8 Nm (100 kgfcm, 7 ftlbf)NOTICE: Do not remove caps until the tube is installed.
3. INSTALL COOLING FAN4. REPLENISH COMPRESSOR OIL IF CONDENSER
HAS BEEN REPLACEDAdd 40 cc (1.4 fl.oz.)Compressor Oil:
ND OIL 8 or equivalent5. EVACUATE AIR IN REFRIGERATION SYSTEM AND
CHARGE WITH REFRIGERANTSpecified amount:
850 50g (33.51 1.76 oz)6. INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak tester, check for leakage of refriger ant.
7. INSTALL REMOVAL PARTSInstall the removal parts in reverse order of removalprocedure.
7. REMOVE CONDENSERRemove the 2 bolts and lean the radiator backward,then remove the cond enser.
AIR CONDITIONING SYSTEM CONDENSERAC48
-
8/14/2019 Air Conditioning System
49/73
EVAPORATOR INSPECTION1. INSPECT FINS FOR BLOCKAGE
If the fins are clogged, clean them with compressedair.NOTICE: Never use water to clean the evaporator.
2. INSPECT FITTINGS FOR CRACKS OR SCRATCHESRepair as necessary.
EVAPORATOREVAPORATOR REMOVAL1. DISCHARGE REFRIGERANT FROM REFRIGERA
TION SYSTEM(See page AC21 )
2. REMOVE BLOWER UNIT(See page AC35 )
3. REMOVE EVAPORATOR COVER(a) Remove 2 bolts for the liquid and suction tube.(b) Remove 8 screws and evaporator cover.
(b) Remove 2 bolts using a hexagon wrench and separatethe evaporator and expansion valve.
4. REMOVE EVAPORATOR(a) Pull and remove the evaporator.
AIR CONDITIONING SYSTEM EVAPORATORAC49
-
8/14/2019 Air Conditioning System
50/73
EVAPORATOR INSTALLATION1. INSTALL REMOVAL PARTS
Install the removal parts in reverse order of removalprocedure.HINT:The tightening torque for the bolt used to install
the expantion valve on the evaporator is shownbelow.Torque: 5.4 Nm (55 kgfcm, 48 in.lbf)The tightening torque for the bolts used to installthe liquid and suction tube is shown below.Torque: 9.8 Nm (100 kgfcm, 7 ftlbf)
2. REPLENISH COMPRESSOR OIL IF EVAPORATORHAS BEEN REPLACEDAdd 40 cc (1.4 fl.oz)Compressor oil:
ND OIL 8 or equivalent
3. EVACUATE AIR IN REFRIGERATION SYSTEM ANDCHARGE WITH REFRIGERANTSpecified amount:
850 50g (29.98 1.76 oz)4. INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak tester, check for leakage of refriger ant.
AIR CONDITIONING SYSTEM EVAPORATORAC50
-
8/14/2019 Air Conditioning System
51/73
HEATER RADIATOR INSTALLATION1. INSTALL HEATER RADIATOR TO A/C UNIT
(a) Put the radiator in the A/C unit.
(b) Connect teh heater pipes.(c) Install the 3 clamps with 3 screws.2. INSTALL HEATER PROTECTOR
HEATER RADIATOR
HEATER RADIATOR REMOVAL1. REMOVE HEATER PROTECTOR
Remove the 2 clips and the heater protector.
HEATER RADIATOR INSPECTIONIf the fin are clogged, clean them with commpressedair.
2. REMOVE HEATER RADIATOR
(a) Remove the 3 screws and the 3 clamps.
(b) Disconnect the heater pipes.(c) Pull the heater radiator out.
AIR CONDITIONING SYSTEM HEATER RADIATORAC51
-
8/14/2019 Air Conditioning System
52/73
WATER VALVE
WATER VALVE REMOVAL1. DRAIN ENGINE COOLANT FROM RADIATOR
HINT: It is not necessary to drain out all the coolant.2. DISCONNECT WATER VALVE CONTROL CABLE
FROM WATER VALVE
3. DISCONNECT WATER HOSE FROM WATER VALVE
3. CONNECT WATER VALVE CONTROL CABLE TO
WATER VALVE
(a) Set the temperature control switch to COOL.(b) Set the water valve lever to COOL, install the control
cable and lock the clamp.HINT: Lock the clamp while lightly pushing the outercable in the direction shown by the arrow.
WATER VALVE INSTALLATION1. INSTALL WATER VALVE
(a) Push the water hose onto the heater radiator pipe asfar as rigs on the pipe and install the hose clip.
(b) Install water valve with the bolt.2. CONNECT HEATER HOSE TO WATER VALVE
4. REMOVE WATER VALVE
(a) Disconnect the water hose from the heater radiatorpipe.
(b) Remove the bolt and the water valve
AIR CONDITIONING SYSTEM WATER VALVEAC52
-
8/14/2019 Air Conditioning System
53/73
-
8/14/2019 Air Conditioning System
54/73
ASV INSPECTION (5SFE ENGINEMODEL)1. CHECK VACUUM CIRCUIT CONTINUITY IN ASV BY
BLOWING AIR INTO PIPES(a) Connect the ASV terminals to the battery terminals as
illustrated.(b) Blow into pipe A and check that air comes out of
pipe B.
3. CHECK FOR OPEN CIRCUITUsing an ohmmeter, measure the resistance betweenthe 2 terminals.Resistance:
30 34 0 at 20
C (68
F)
If resistance value is not as specified, replace the ASV.
(c) Disconnect the battery.(b) Blow into pipe A and check that air does not come
out of pipe B.If a problem is bound, replace the ASV.
2. CHECK FOR SHORT CIRCUITUsing an ohmmeter, check that there is no continuitybetween each terminal and the ASV.If there is continuity, replace the ASV.
AIR SWITCHING VALVE (ASV)VACUUM HOSE CIRCUIT (5SFE ENGINEMODEL)
AIR CONDITIONING SYSTEM AIR SWITCHING VALVE (ASV)AC54
-
8/14/2019 Air Conditioning System
55/73
BLOWER MOTOR INSTALLATION1. INSTALL MOTOR(a) Install the motor with the 3 screws.(b) Connect the connector.2. INSTALL CONNECTOR BRACKET3. INSTALL INSTRUMENT LOWER PANEL AND
UNDER COVER NO. 2
BLOWER MOTORBLOWER MOTOR REMOVAL1. REMOVE INSTRUMENT LOWER PANEL AND
UNDER COVER NO. 2(See page BO108 )
2. REMOVE CONNECTOR BRACKETRemove the 2 screws and the bracket
BLOWER MOTOR INSPECTIONINSPECT BLOWER MOTOR OPERATIONConnect the positive (+) lead from the battery toterminal 2 and the negative () lead to terminal 1,then check that the motor operation is smooth.
3. REMOVE MOTOR(a) Disconnect the connector.(b) Remove the 3 screws and the motor.
AIR CONDITIONING SYSTEM BLOWER MOTORAC55
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
56/73
CONDENSER FAN MOTORCONDENSER FAN MOTOR INSPECTION5SFE ENGINE MODEL:1. DISCONNECT CONNECTOR2. INSPECT CONDENSER FAN MOTOR
Connect positive (+) lead from battery and negative() lead to terminals, then check that the condenserfan motor operates smoothly.Standard current:
6.7 1 (A)
If current value is not as specified, replace the con denser fan motor.
AIR CONDITIONING SYSTEM CONDENSER FAN MOTORAC56
-
8/14/2019 Air Conditioning System
57/73
AIR INLET SERVOMOTOR INSPECTIONINSPECT SERVOMOTOR OPERATION
(a) Connect the positive (+) lead from the battery toterminal 1 and the negative () lead to terminal 2,check that the arm rotates to the FRESH side smoot hly.
AIR INLET SERVOMOTOR INSTALLATION1. INSTALL SERVOMOTOR(a) Install the servomotor with the 2 screws.(b) Connect the connector.2. INSTALL ECU AND ECU BRACKET3. INSTALL GLOVE COMPARTMENT
(b) Connect the positive (+) lead from the battery toterminal 1 and the negative () lead to terminal 3,check that the arm rotates to the RECI RC side smo othly.If operation is not as specified, replace the servomotor.
AIR INLET SERVOMOTORAIR INLET SERVOMOTOR REMOVAL1. REMOVE GLOVE COMPARTMENT
(See page BO108 )2. REMOVE ECU AND ECU BRACKET
3. REMOVE SERVOMOTOR(a) Disconnect the connector.(b) Remove the 2 screws and the servomotor.
AIR CONDITIONING SYSTEM AIR INLET SERVOMOTORAC57
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
58/73
-
8/14/2019 Air Conditioning System
59/73
BLOWER RESISTORBLOWER RESISTOR REMOVAL1. REMOVE INSTRUMENT LOWER FINISH PANEL
(See page BO108 )2. REMOVE BLOWER RESISTOR(a) Disconnect the connector from the resistor.(b) Remove the 2 screws and the resistor.
BLOWER RESISTOR INSTALLATION1. INSTALL BLOWER RESISTOR(a) Install the resistor with the 2 screws.(b) Connect the connector to the resistor.2. INSTALL INSTRUMENT LOWER FINISH PANEL
If continuity is not as specified, replace the blower
resistor.
If continuity is not as specified, replace the blowerresistor.
INSPECT BLOWER RESISTOR CONTINUITYContinuity
BLOWER RESISTOR INSPECTION
Tester connectoin toterminal number
Tester connectoin toterminal number
t 2356
Specified value
Specified value
1236 Continuity
Continuity
Condition
Condition
Constant
Constant
AIR CONDITIONING SYSTEM BLOWER RESISTORAC59
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
60/73
Cooling Fan Control:(a) Connect the positive (+) lead from the ohmmeter to
terminal 2 and negative () lead to terminal 3.(b) Check continuity between terminals when refrigerant
pressure is changed, as shown.If operation is not as specified, replace the pressureswitch.
5. STOP ENGINE AND REMOVE MANIFOLD GAUGESET
6. CONNECT CONNECTOR TO PRESSURE SWITCH
PRESSURE SWITCHONVEHICLE INSPECTION1. INSTALL MANIFOLD GAUGE SET
(See page AC21 )2. DISCONNECT CONNECTOR FROM PRESSURE
SWITCH3. RUN ENGINE AT APPROX. 2000 RPM
Magnet Clutch Control:(a) Connect the positive (+) lead from the ohmmeter to
terminal 4 and negative () lead to terminal 1.(b) Check continuity between terminals when refrigerant
pressure is changed, as shown.If operation is not as specified, replace the pressureswitch.
4. INSPECT PRESSURE SWITCH OPERATION
AIR CONDITIONING SYSTEM PRESSURE SWITCHAC60
-
8/14/2019 Air Conditioning System
61/73
-
8/14/2019 Air Conditioning System
62/73
EVAPORATOR TEMPERATURE SENSORINSPECTION
Check resistance between terminals of evaporatortemperature sensor (thermistor) connector at eachtemperature.Resistance:
at 0 _ C (32 _ F): 4.6 5.1 k W
at 15 _ C (59 _ F): 2.1 2.6 k WIn addition as temperature increases, the resistancedecreases gradually.
EVAPORATOR TEMPERATURESENSOREVAPORATOR TEMPERATURE SENSORREMOVAL
REMOVE EVAPORATOR TEMPERATURE SENSORRemove the screw and the evaporator temperaturesensor (thermistor).
EVAPORATOR TEMPERATURE SENSORINSTALLATION
INSTALL EVAPORATOR TEMPERATURE SENSORInstall evaporator temperature sensor in reverse orderof removal procedure.
AIR CONDITIONING SYSTEM EVAPORATOR TEMPERATURE SENSORAC62
-
8/14/2019 Air Conditioning System
63/73
3. INSPECT REVOLUTION DETECTING SENSORCheck the resistance between terminals 1 and 2 of thesensor.Specified resistance:
5SFE:165 205 W at 20 _ C (68 _ F)1 MZ FE:65 125 W at 20 _ C (68 _ F)
If the resistance value is not as specified, replace therevolution detecting sensor.
REVOLUTION DETECTING SENSORREMOVAL1. REMOVE COMPRESSOR
(See page AC37 )2. REMOVE REVOLUTION DETECTING SENSOR(a) Remove 2 bolts.(b) Remove the revolution detecting sensor.
REVOLUTION DETECTING SENSORONVEHICLE INSPECTION1. DISCONNECT NEGATIVE () CABLE FROM BAT
TERYCAUTION: Work must be started after 90 seconds fromthe time the ignition swithch is turned LOCK positionand the negative () terminal cable is disconnected fromthe battery.
2. DISCONNECT CONNECTOR OF REVOLUTION DETECTING SENSOR
REVOLUTION DETECTING SENSORINSTALLATION1. INSTALL REVOLUTION DETECTING SENSOR
Using a torque wrench, tighten the bolts.Torque:6 Nm (60 kgfcm, 4 ftlbf)
2. INSTALL COMPRESSOR(See page AC46 )
AIR CONDITIONING SYSTEM REVOLUTION DETECTING SENSORAC63
-
8/14/2019 Air Conditioning System
64/73
RELAYRELAYS REMOVAL1. DISCONNECT NEGATIVE () CABLE FROM BAT
TERYCAUTION: Work must be started after 90 seconds fromthe time the ignition switch is turned to the LOCKposition and the negative () terminal cable is disconnected from the battery.
2. REMOVE RELAYS
RELAYS INSPECTION1. INSPECT MAGNET CLUTCH RELAY CONTINUITY
If continuity is not as specified, replace the relay.2. INSPECT A/C FAN RELAY NO. 2 CONTINUITY
5SFE Engine Model:
If continuity is not as specified, replace the relay.3. INSPECT A/C FAN RELAY NO. 3 CONTINUITY
5SFE Engine Model:
If continuity is not as specified, replace the relay.
Tester connection toterminal number
Tester connection toterminal number
Tester connection toterminal number
Apply6 + betweenterminals 1 and 4.
Apply B + betweenterminals 1 and 4.
Apply B + betweenterminals 1 and 4.
Specified value
Specified value
Specified value
1 43 5
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Condition
Condition
Condition
Constant
Constant
Constant 1 4
1 4
2 3
2 3
2 3
AIR CONDITIONING SYSTEM RELAYAC64
-
8/14/2019 Air Conditioning System
65/73
-
8/14/2019 Air Conditioning System
66/73
AIR CONDITIONING AMPLIFIER
A/C AMPLIFIER INSPECTIONINSPECT AMPLIFIER CIRCUIT
Disconnect the amplifier and inspect the connector onthe wire harness side, as shown in the chart below.Test conditions Ignition switch : ON Temperature control dial : MAX COOL Blower dial: HI
If circuit is not as specified, replace the amplifier.
Refrigerant pressure: less than 196 kPa ormore than 3140 kPa
Refrigerant pressure: 196 3140 kPa
Approx. 115 W at 20 _ C (68 _ F)
1.5 k W at 20 _ C (68 _ F)
Turn A/C switch OFF
Turn A/C switch OFF
Turn A/C switch OFF
Specified condition
Turn A/C switch ON
Turn A/C switch ON
Turn A/C switch ON
Tester connection
Battery voltage
Battery voltage
Battery voltage
Battery voltage
10 Ground
12 Ground
10 Ground
12 Ground
No voltage
No voltage
No voltage
No voltage
2 Ground
Continuity
8 Ground
8 Ground
5 Ground
2 Ground
Condition
Constant
Constant
Constant1413
913
AIR CONDITIONING SYSTEM AIR CONDITIONING AMPLIFIERAC66
-
8/14/2019 Air Conditioning System
67/73
AIR CONDITIONING CONTROLASSEMBLYA/C CONTROL ASSEMBLY REMOVAL(See page BO108 )A/C CONTROL ASSEMBLY INSPECTION(ROTARY SWITCH AND PUSH BUTTONTYPE)
2. INSPECT MODE INDICATOR(a) Connect the positive (+) lead from the battery to
terminal A12 and the negative () lead to terminalA1.
(b) Push each of the mode bottons in and check that theirindicators light up.If operation is not as specified, replace the A/C con trol assembly.
1. INSPECT A/C INDICATOR(a) Connect the positive (+) lead from the battery to
terminal A12 and the negative () lead to terminalA4.
(b) Push the A/C button in and check that the indicatorlight up.If operation is not as specified, replace the A/C con trol assembly.
AIR CONDITIONING SYSTEM AIR CONDITIONING CONTROL ASSEMBLYAC67
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
68/73
4. INSPECT INDICATOR DIMMING OPERATION(a) Connect the positive (+) lead from the battery to
terminal A 12 and the negative () lead to terminalA 1.
(b) Connect the positive (+) lead from the battery toterminal A14 and check that the mode indicatordims.
If operation is not as specified, replace the A/C con trol assembly.
3. INSPECT AIR INLET INDICATOR(a) Connect the positive (+) lead from the battery to
terminal A 12 and the negative () lead to terminalA1.
(b) Check that the FRESH and RECIRC indicators light upalternately each time the air inlet control switchbutton is pressed.If operation is not as specified, replace the A/C con trol assembly.
If continuity is not as specified, replace the A/C con trol assembly.
5. INSPECT A/C SWITCH CONTINUITY
Tester connection toterminal numberSwitch position Specified value
No continuity
ContinuityA7 A8
OFF
AIR CONDITIONING SYSTEM AIR CONDITIONING CONTROL ASSEMBLYAC68
-
8/14/2019 Air Conditioning System
69/73
7. INSPECT AIR INLET CONTROL SWITCH CONTINUITY
If continuity is not as specified, replace the A/C control assembly.
If continuity is not as specified, replace the A/C con
trol assembly.
6. INSPECT MODE CONTROL SWITCH CONTINUITY
Tester connection toterminal number
Tester connectoin toterminal number
Switch position Specified value
Switch position Specified value
FOOT/ oeF
A11 Al
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
A10 A1
A2 A 1
A3 A 1
A5 A 1
A9 A 1
A6A1
RECIRC
FRESH
FOOT
FACEB/L
D EF
AIR CONDITIONING SYSTEM AIR CONDITIONING CONTROL ASSEMBLYAC69
-
8/14/2019 Air Conditioning System
70/73
-
8/14/2019 Air Conditioning System
71/73
If continuity is not as specified, replace the switch.3. INSPECT BLOWER SPEED CONTROL SWITCH CON
TINUITY
2. INSPECT MODE CONTROL SWITCH CONTINUITY
If continuity is not as specified, replace the switch.
ROTARY SWITCH AND LEVER TYPE:
1. INSPECT A/C SWITCH CONTINUITY
Tester connection toterminal number
Tester connection toterminal number
Specified value
Specified value
Switch position
Switch position
No continuity
FOOT/ DEF
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
18
15
1 6
1 7
14
OFF.
FOOT
2 5
B/ LFACE
DEF
AIR CONDITIONING SYSTEM AIR CONDITIONING CONTROL ASSEMBLYAC71
-
8/14/2019 Air Conditioning System
72/73
A/C CONTROL CABLES ADJUSTMENT1. ADJUST AIR INLET DAMPER CONTROL CABLE
Set the air inlet damper and the control lever to FRESH position, install the control cable and lock theclamp.
2. ADJUST AIR MIX DAMPER CONTROL CABLESet the air mix damper and control switch to COOLposition, install the control cable and lock the clampwhile lightly pushing the outer cable in the directionshown by the arrow.
A/C CONTROL ASSEMBLYINSTALLATION
(See page BO108 )
If continuity is not as specified, replace the switch.
Switch position
Terminal
OFF
AIR CONDITIONING SYSTEM AIR CONDITIONING CONTROL ASSEMBLYAC72
http://bo.pdf/http://bo.pdf/ -
8/14/2019 Air Conditioning System
73/73
SERVICE SPECIFICATIONSSERVICE DATA
TORQUE SPECIFICATIONS
Pressure switch x Liquired tube
Discharge hose x Compressor
Expansion valve x Evaporator
Magnetic clutch noT engaged
Magnetic clutch no engaged
Suction hose x Compressor
Magnetic clutch engaged
Refrigerant charge volume
Magnetic clutch clearance
Magnetic clutch engaged
Suction tube x A/C unit
Liquid tube x A/C unit
Compressor x Engine
Lequid x Condensor
Liquid x Receiver
Drive belt tention
Part tightened
Idle speed
1 MZ FE:
1 MZ FE:
Used belt
Used belt
New belt
New belt5SFE:
5SFE:
AIR CONDITIONING SYSTEM SERVICE SPECIFICATIONSAC73