aii30280 xm radio system - honda · receiver unit display module antenna xm radio harness fm...

© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30280 (0509) 1 of 2408B15-SDA-1001-91

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

SEP 2005

ACCORD 4 DOORXM RADIO SYSTEM

PARTS LIST

XM Radio Attachment Kit (sold separately):P/N 08B15-SDA-100

DIN cable

XM radio harness

Front unit bracket

Rear unit bracket

Bracket A

Bracket B

Bracket C

Template

Double-sided adhesive tape

Display module pocket

Fastener

Ground bolt (gold)

6 Washer-screws, 4 x 8 mm

6 Washer-bolts, 6 x 12 mm

4 Flange nuts, 4 mm

Clip nut

3 Self-tapping screws

29 Wire ties

AII 30280

The XM Radio will not fit in a vehicle equipped witha rear entertainment system.

dcs

HandA-Accessories.com

2 of 24 AII 30280 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.

Base Kit (sold separately):P/N 08A15-1E1- 000

Connector clip

8 Wire tie with clips (two not used)

5 Cushion tapes

5 EPT sealers

Fuse label

Mini fuse, 5A

Antenna Kit (sold separately):P/N 08A15-1E1-100

Antenna cable

Display Module

FM modulator unit

Receiver unit

Owner's Manual

© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30280 (0509) 3 of 24

Audio Attachment Kit (sold separately):P/N 08B06-SDA-100(Not required if already equipped with a player.)

Left player bracket

Right player bracket

Left player subbracket

Right player subbracket

Player base-bracket

Player panel

Pocket

BUS cable(Used on vehicles without a navigation system)

2 Latches

8 Flange nuts, 6 mm

2 Grommet screws

2 Wire ties

3 EPT sealers

2 Self-tapping screws, 4 x 12 mm

Audio Subharness (sold separately):P/N 08A31-0E1-010

If the vehicle is equipped with a navigation systemand already has an installed cassette/MP3/CDplayer, use this audio subharness cable. Do notuse this cable when the vehicle is to be equippedwith the XM radio only.

Audio subharness cable(Used on vehicles with anavigation system)


Illustration of the XM Radio System Installed in theVehicle

TOOL AND SUPPLIES REQUIREDPhillips screwdriverStubby phillips screwdriverFlat-tip screwdriverIsopropyl alcoholShop towelTape measureUtility knifeHook toolRatchet wrench8 mm and 10 mm SocketsFelt-tip penScissorsPush pinVinyl tapeDrill3 mm and 10 mm Drill bitsTouch-up paintEye protection (face shield, safety goggles, etc.)Masking tape

2N28160M

RECEIVERUNIT ANTENNADISPLAY MODULE

XM RADIOHARNESS

FM MODULATORUNIT

DIN CABLE

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

2N28010M

DISPLAYMODULE

FM MODULATORUNIT

RECEIVER UNITFUSE BOX6-PINCONNECTOR

VEHICLEANTENNACABLE

ANTENNA

XM RADIOHARNESS

DIN CABLE


3. Remove the trim ring.

M/T Vehicle:

• Squeeze the plastic clip, and pull down on theshift boot. Remove the shift knob by turning itcounterclockwise.

• Gently pry up on the trim ring to release the sixclips.

• Unplug the two seat heater connectors(if equipped), and remove the trim ring.

A/T Vehicle:

• Gently pry up on the trim ring to release the sixclips.

• Unplug the two seat heater connectors(if equipped), and remove the trim ring.

4. Remove the center holder.

• Open the lid, and remove the coin pocket.

• Remove the two self-tapping screws.

• Gently pull out the dashboard center holder torelease the two retaining clips, unplug thevehicle connector, and remove the centerholder.

2206032K

SHIFT KNOB(Turn counterclockwise.)

PLASTICCLIP

SHIFTBOOT

2206041K

RETAININGCLIPS (4)

RETAININGCLIPS (2)

TRIMRING

SEAT HEATERCONNECTOR(if equipped)

2206112K

RETAININGCLIPS (4)

RETAININGCLIPS (2)

TRIM RING

SEAT HEATERCONNECTOR(if equipped)

2206061K

COINPOCKET

CENTER HOLDER

SELF-TAPPINGSCREW

RETAININGCLIPS (2)

LID

VEHICLECONNECTOR

With Coin Pocket:


If the vehicle is equipped with a Cassette/MP3/CDPlayer, go to step 13; otherwise, go to step 5.

5. Remove the pocket:

• Apply masking tape to the edge of the centerpanel.


• Push in on the bottom of the lid, then pull outon the top by inserting the end of a hook toolbetween the pocket and center panel. Pull thepocket toward you to release the two retainingclips.

• Set the pocket aside; it will not be reused.

With Optional Ashtray:

• Open the lid, and remove the ashtray.


• Gently pull out on the two retaining clips,unplug the cigarette lighter harness connector,vehicle connector, illumination bulb, andremove the center holder.

6. Remove the right and left inner covers (one hookand one clip for each cover). Set the inner coversaside; they will not be reused.

2730010K

SELF-TAPPINGSCREW

ASHTRAY

CENTERHOLDER

ILLUMINATIONBULB

CIGARETTELIGHTERHARNESSCONNECTOR

VEHICLECONNECTOR

RETAININGCLIPS (2)

2206073K

HOOKTOOL

POCKET

SELF-TAPPINGSCREW

RETAININGCLIPS (2)

MASKINGTAPE

POCKETLID

2226010K

CLIP

LEFT INNERCOVER

HOOK

POCKETOPENING

RIGHT INNERCOVER


8. Insert the studs from the player base-bracket intothe holes in the vehicle frame from the back.Install the two 6 mm flange nuts while holding thebracket firmly against the vehicle frame. Insert thevehicle harness clip (removed in step 7) into thehole in the player base-bracket.

9. Insert the studs of the left and right playersubbrackets into the holes in the vehicle frame,and install one 6 mm flange nut on the end ofeach stud while pushing each subbracket upward.

7. Remove the vehicle harness clip from the vehicleframe, and move the clip out of the way.

10. Get the pocket from the audio attachment kit.Using a utility knife, cut the two lugs off of thepocket.

11. Install one latch onto the left and right playerbrackets. Slide the clip nut onto the displaymodule pocket flange.

2306011T

PLAYER BASE-BRACKET VEHICLE

FRAME

VEHICLEFRAME

6 mmFLANGENUT

VEHICLEHARNESSCLIP(Remove.)

6 mmFLANGENUT

VEHICLE HARNESS CLIP(Insert into the hole ofthe player base-bracket.)

2306021T

LEFT PLAYERSUBBRACKET

RIGHT PLAYERSUBBRACKET

VEHICLEFRAME

6 mm FLANGE NUT

VEHICLEFRAME

2529041T

LUG(Cut off.)

LUG

POCKET

12 Set the display module pocket on the pocket withthe cut out facing up. Position the left and rightplayer brackets on the display module pocket andpocket, and install five self-tapping screws.

2N28071M

LEFTPLAYERBRACKET

SELF-TAPPINGSCREW (2)(suppliedwith audioattachment kit)

SELF-TAPPINGSCREWS (3)(supplied withXM radioattachment kit)RIGHT

PLAYERBRACKET

POCKET

LATCH LATCH1 mm

DISPLAYMODULEPOCKET

DISPLAYMODULEPOCKETFLANGE

CLIP NUT

SCREWPOSITION

BRACKETHOLE


If the vehicle is not equipped with a Cassette/MP3/CD Player, go to step 18; otherwise, go to step 13.

13. Remove the player panel by removing the twoself-tapping screws and two clips.

14. Remove the player/pocket assembly. Unscrew thefour flange nuts, and pull the assembly out towardyou. Unplug the audio subharness cableconnector.

15. Remove the left and right audio brackets (twowasher-screws and one self-tapping screw foreach bracket). Separate the player and pocket.Set the pocket aside; it will not be reused.

2306141T

CLIP

SELF-TAPPINGSCREW

PLAYER PANEL

VEHICLECONNECTOR(withoutnavigationsystem)

VEHICLE CONNECTOR(with navigation system)

AUDIOSUBHARNESSCONNECTOR(with navigationsystem)

AUDIOSUBHARNESSCONNECTOR(withoutnavigationsystem)

LEFT PLAYERBRACKET

6 mmFLANGENUT

RIGHTPLAYERBRACKET

RIGHT PLAYERSUBBRACKET

PLAYER BASE-BRACKET


2N28080M

WASHER-SCREW

SELF-TAPPINGSCREW

LEFT AUDIOBRACKET

PLAYER(Cassette/MP3/CD)

RIGHT AUDIOBRACKET

WASHER-SCREW

POCKET(Do not reuse.)

16. Slide the clip nut (supplied) onto the displaymodule flange.

17. Set the player on the display module pocket.Position the left and right player brackets on thedisplay module pocket and player, and reinstallthe four washer-screws. Install the three self-tapping screws to secure the display modulepocket.

SELF-TAPPINGSCREW

PLAYER(Cassette/MP3/CD)

SELF-TAPPINGSCREWS (2)(supplied withXM radioattachment kit)

RIGHTPLAYERBRACKET

WASHER-SCREW(suppliedwithaudioattachmentkit)

LEFTPLAYERBRACKET

BRACKETHOLE

SCREWPOSITION

DISPLAYMODULE

SELF-TAPPINGSCREW

CLIP NUT

DISPLAYMODULEPOCKET

WASHER-SCREW(suppliedwith audioattachmentkit)


Installing the Display Module

18. Attach the display module to the display modulepocket:

• Using isopropyl alcohol on a shop towel, cleanthe back of the display module where theadhesive backing will attach.

• Remove the backing from one side of thedouble-sided adhesive tape, and attach it tothe display module.

• Remove the remaining backing from thedouble-sided adhesive tape. Route the displaymodule cable through the hole of the displaymodule pocket, and attach the display moduleto the pocket.

2N28110M

DISPLAY MODULE

Clean withisopropylalcohol.

DOUBLE-SIDEDADHESIVE TAPE

BACKING

DISPLAYMODULEPOCKET

POCKET

PLAYERWith Player

Without Player

DISPLAYMODULEPOCKET

Routing the XM Radio Harness

19. Remove the beverage holder (pull up to releasethe six retaining clips).

20. Remove the rear console.

• Open the lid, and remove the rear console matfrom inside the rear console.

• Remove the two screws and four self-tappingscrews, and unplug the connector and harnessclip (if equipped).

• If equipped with a console-mounted CDchanger, remove the changer from the rearconsole.

2206050K

RETAININGCLIPS (4)

RETAININGCLIPS (2)

BEVERAGEHOLDER

2206090K

SCREWS (2)

REAR CONSOLE MAT

CONNECTOR(if equipped)

SELF-TAPPINGSCREWS (4)

HARNESS CLIP(if equipped)

DISPLAYMODULECABLE

DISPLAY MODULE CABLE


21. Remove the driver’s dashboard lower cover:

• Remove the self-tapping screw.

• First release the four clips on the left side bypulling out on the driver's dashboard lower cover.

• After releasing the four clips, insert a flat-tipscrewdriver behind the clip at the dashboardframe. Gently twist the screwdriver to releasethe clip.

• Release the two clips on the right side. Unplugthe vehicle connector, and then remove thelower cover.

22. If equipped, remove the driver’s dashboard undercover (release the three retaining clips, one pin,and one holder).

23. Remove the self-tapping screw and the clip thatsecure the left front console cover. Take care notto damage the clip, and remove the consolecover.

2205020T

HOLDER

RETAININGCLIPS (3)

DRIVER’S DASHBOARDUNDER COVER

PIN

2206131K

SELF-TAPPINGSCREW

LEFT FRONTCONSOLE COVER

CLIP

PUSH REMOVE

2524010M

GLOVEBOX

DAMPER ROD

BOLTS (2)

PUSH2206120K

CONNECTOR DASHBOARDLOWER COVER

RETAININGCLIPS (7)SELF-

TAPPINGSCREW

24. Remove the glove box by removing the two bolts,and then release the damper rod.


27. Install the XM radio harness fuse cases and the6-pin dummy connector to the fuse box case.

28. Secure the XM radio harness to the vehicleharness with one wire tie. Do not secure it to theyellow SRS harness.

29. Route the XM radio harness under the steeringshaft and toward the center console.

2N28020M

(Do notsecure itto theyellowSRSharness.)

FUSECASES

VEHICLEHARNESS

XM RADIOHARNESS

WIRE TIE

XM RADIO HARNESS6-PIN CONNECTORWITH DUMMYCONNECTOR

Fuse case position

2524060M

OTHERACCESSORY6-PINHARNESS

DUMMYCONNECTOR(Discard.)

XM RADIO HARNESS6-PIN CONNECTOR

25. On the driver's side of the vehicle, locate the 6-pinconnector on the fuse box. Plug the XM radioharness 6-pin connector into the fuse box 6-pinconnector.

2524051M

FUSE BOX6-PINCONNECTOR

6-PINCONNECTOR

XM RADIOHARNESS

FUSECASES

FUSELABEL

2ALABEL

5ALABEL

CLIP

26. Attach the fuse labels to the fuse cases on theXM radio harness.

NOTE: If the 6-pin connector is already being usedby another accessory, locate the 6-pin connectortaped to the XM radio harness. Remove thedummy connector from the harness, and plug theother accessory's harness 6-pin connector into theXM radio harness.

2N28030M

VEHICLE HARNESS

WIRE TIES (3)

CENTERCONSOLE

XM RADIOHARNESS

30. Loosely attach the XM radio harness to thevehicle harness with three wire ties.

3121030M

Use theselabels.

FUSE LABEL


32. Route the XM radio harness 3-pin connectortoward the glove box opening. Set the remainingXM radio harness aside; it will be routed later.

If the vehicle is not equipped with a Cassette/MP3/CD Player, go to step 34; otherwise, go tostep 33.

33. Plug the audio subharness cable into the player.

Without Navigation System:

Cassette Player

Make loops in the audio subharness cable, andsecure it with one wire tie, so that the distancebetween the ends of the cable connector is200 mm. Plug the audio subharness cableconnector into the cassette player connector.

31. Inside the center console, locate the welded nuton the vehicle stay. Attach the XM radio harnessground terminal to the welded nut with the groundbolt supplied.

2N28040M

GROUNDTERMINAL

3-PINCONNECTOR

CENTERCONSOLE

XM RADIOHARNESS

GROUND BOLT(supplied)

WELDEDNUT

2306051T

200 mm

CASSETTEPLAYER

WIRE TIE(supplied withaudioattachment kit)

AUDIOSUBHARNESSCABLE AUDIO

SUBHARNESSCABLECONNECTOR

AUDIOSUBHARNESSCABLECONNECTOR

Multimedia Player

Make loops in the audio subharness cable, andsecure it with one wire tie so that the distancebetween the ends of the cable connectors is200 mm. Plug the audio subharness cableconnector into the multimedia playerconnector.

2306061T

MULTIMEDIAPLAYER


BUS CABLE

200 mm




In-Dash CD Player

• Make loops in the audio subharness cable, andsecure it with one wire tie so that the distancebetween the ends of the cable connector is180 mm. Plug the audio subharness cableconnector into the connector from the in-dashCD player.

• After connecting, secure the connectors to therear of the in-dash player with one wire tie fromthe in-dash CD player kit.

With Navigation System:

Remove the tape that secures the vehicleharness to the upper left pocket opening, andpull the harness out through the pocketopening.

Cassette Player

2306070T

180 mm


AUDIOSUBHARNESSCABLE

IN-DASH CDPLAYER

WIRE TIE(supplied withaudioattachmentkit)


2306090T

CASSETTEPLAYER AUDIO

SUBHARNESSCABLECONNECTOR

AUDIO SUBHARNESSCABLE

2306080T

TAPE(Remove.)

POCKETOPENING

VEHICLECONNECTOR

Multimedia Player

2306100T


MULTIMEDIAPLAYER

In-Dash CD Player

After connecting, secure the connectors to therear of the in-dash CD player with one wire tiefrom the in-dash CD player kit.

2306110T

IN-DASH CDPLAYER

WIRE TIE(suppliedwith audioattachmentkit)


IN-DASH CDCHANGERCONNECTOR





2506010T

MASKINGTAPE

CENTERPANEL

34. To protect the center panel, attach strips ofmasking tape to the center panel in the areashown.

37. Inside the glove box opening, locate the framestay pipe. Align the holes in the frame stay pipewith the welded nuts in bracket A, and looselyattach bracket A to the pipe frame with two6 x 12 mm washer-bolts.

38. Attach the connector clip to the harness connectorof the FM modulator unit. Attach bracket B tothe FM modulator unit with one 4 x 8 mmwasher-screw. Tighten the washer-screw securely.

35. Get a DIN cable from the XM radio attachment kit.Route the 90° end of the DIN cable through thedashboard opening and toward the FM modulatorunit.

2N28120M

DIN CABLE(90° end)

TO THE FMMODULATORUNIT

DISPLAY MODULECABLE

DISPLAY MODULEASSEMBLY

36. Place the display module assembly near thedashboard opening, and route the display modulecable toward the FM modulator unit along the XMradio harness (3-pin connector) and the DIN cable.

2524100M

6 x 12 mmWASHER BOLT

6 x 12 mmWASHER-BOLT

FRAME STAYPIPE

BRACKET A

2524121M

BRACKET B

FMMODULATORUNIT

CONNECTORCLIP

4 x 8 mmWASHER-SCREW

XM RADIOHARNESS

(with player)

(with pocket)


39. Plug the DIN cable and the display module cableinto the FM modulator unit.

40. Attach bracket B with the FM modulator unitagainst bracket A, and install one additional6 x 12 mm washer-bolt. Tighten all three6 x 12 mm washer-bolts securely.

41. Route the antenna harnesses from the FMmodulator unit rearward along the DIN cabletoward the inside of the front console.

42. Below the glove box opening, remove the upperheater blower case mounting bolt.

43. Attach bracket C to the bottom of the FMmodulator unit with one 4 x 8 mm washer-screw,and attach the other end of bracket C to the upperheater blower using the bolt you removed instep 42.

BRACKET A

6 x 12 mmWASHER-BOLT

BRACKET B

DIN CABLE

DISPLAYMODULECABLE

FM MODULATORUNIT

FM MODULATOR UNITANTENNA HARNESSES

WIRE TIEWITH CLIP

FMMODULATORUNIT

BRACKET C

4 x 8 mmWASHER SCREW

VEHICLEBOLT(reused)

FM MODULATORUNIT HARNESS3-PIN CONNECTOR

FM MODULATORUNIT ANTENNAHARNESS

2524111M

BOLT(Reuse.)

HEATERBLOWER CASE

44. On the back of the FM modulator unit, attach onewire tie with clip to the antenna harnesses,and attach the wire tie with clip to the hole inbracket C.

FM MODULATORUNIT ANTENNAHARNESSES

FM MODULATOR

FM MODULATOR UNITHARNESS 3-PINCONNECTOR


45. Connect the XM radio harness 3-pin connector tothe FM modulator unit harness 3-pin connector,then attach the 3-pin connector clip to the hole inbracket B.

48. Secure the XM radio harness to the vehicleharness with one wire tie.

2N28130M

VEHICLE ANTENNA CABLEFM MODULATORANTENNA CABLE

EPT SEAL

WIRE TIE

XM RADIO HARNESS3-PIN CONNECTOR

FM MODULATOR UNIT HARNESS3-PIN CONNECTOR

BRACKET B

46. Unplug the vehicle antenna cable, and plug it intothe FM modulator unit antenna cable. Plug theother FM module antenna jack into the vehicleantenna cable.

47. Wrap one EPT seal around the antenna jack, andsecure the antenna jack to the vehicle antennajack with one wire tie. Secure the DIN cable, thedisplay module cable, and the antenna harness tothe vehicle harness with one wire tie.

WIRE TIE2N28140M

WIRE TIE XM RADIOHARNESS

DISPLAYMODULEASSEMBLY

49. Bundle up the excess display module cable, andsecure it with one wire tie.

WIRE TIEDISPLAYMODULECABLE(Bundle up.)

(with player)

(with pocket)


50. Plug the BUS cable connector into the vehicleconnector. If the vehicle is equipped with anavigation system, plug the subharness connectorinto the vehicle connector, and wrap theconnectors with one EPT sealer.

53. Get one EPT sealer. Measure the EPT sealer, anduse scissors to cut it into three pieces.

2612010T

EPT SEALER(Cut off themarked area.)

PLAYERPANEL

8 mm

8 mm

EPT SEALER

2306141T

SELF-TAPPINGSCREW(Reuse.)

LATCH

PLAYERPANEL

CLIP

2306131TGROMMET SCREW

PLAYERPANEL

51. Install the display module assembly onto thestuds of the left and right player subbrackets, andinstall the 6 mm flange nuts. Tighten the flangenuts securely.

52. If the vehicle is not equipped with a player, attachthe two grommet screws to the player panel in thesquare holes as shown.

54. Using isopropyl alcohol on a shop towel, clean theplayer panel in the area shown. Attach the two cutpieces of the EPT sealer to the player panel, andcut off the excess.

55. Attach the player panel by inserting the clips intothe latches, and install two self-tapping screwsfrom the kit, or reinstall the two self-tappingscrews you removed in step 13. Remove themasking tape.

6 mmFLANGENUTS (4)

VEHICLECONNECTOR(without navigationsystem)

VEHICLECONNECTOR(with navigationsystem)

AUDIOSUBHARNESSCONNECTOR(withnavigationsystem)

BUS CABLECONNECTOR(withoutnavigationsystem)LEFT PLAYER

BRACKET

RIGHT PLAYERBRACKET


STUD

EPT SEALER

DISPLAYMODULEASSEMBLY

(with pocket)

(withplayer)


56. Inside the passengers' compartment, remove therear seat cushion by removing the bolt andreleasing the two locks (pull the hook out towardyou).

2226040K

BOLT

REAR SEATCUSHION

HOOK(Pull.)

LOCK (2)59. Remove the spare tire cover (one clip).

57. Remove the right side cushion by removing onebolt and one hook.

58. Inside the trunk, fold the rear seat-back forward bypulling the lever under the rear shelf.

2527030M

CUSHIONHOOK

BOLT

2322010T

CLIP

SPARE TIRE COVER

2527040M

REAR SEAT BACK

LEVER(Pull.)

Pull.

Pull down.


61. Remove the maintenance lid. Remove the jackcover and the jack.

62. Remove the right trunk side trim panel liner:

• If equipped, remove the hook (one bolt, hook,and washer).

• Remove the four clips.

• Gently pull out on the trunk liner, and removeit.

2502010T

MAINTENANCE LID

JACK

JACK COVER

2527060M

HIGHT MOUNTBRAKE LIGHTASSEMBLY

HIGH MOUNTBRAKE LIGHTCONNECTOR

REAR SHELF

HOOKS (4)

2527050M

WASHER

HOOK(if equipped)

CLIPS (4)

Remove

BOLT

60. Remove the rear trim panel (four clips).

2325010T

REAR TRIM PANEL

TRUNKWEATHERSTRIP

CLIPS (4)

63. Inside the trunk area, unplug the high mount brakelight harness connector. Inside the cabin, removethe high mount brake light from the rear shelf byreleasing the four hooks, and pulling out on thebrake light assembly. Take care not to damagethe clips.


65. Raise the rear seat back. Pull the XM radio harnessand DIN cable out from under the floor carpet andtoward the passenger's side of the vehicle. Securethe harness and DIN cable to the vehicle harnesswith two wire ties. Attach the harness and DIN cableto the floor panel with four cushion tapes in theareas shown.

66. Remove the spacer from the rear quarter panelopening.

2527080M

CUSHIONTAPES (4)

WIRE TIES (2)

VEHICLEHARNESS

VEHICLEHARNESS CLIP

REARSEATBACK

FLOORPANEL

Align.

2527090M

SPACER(Remove andreinstall.)

WIRE TIE

BLACKSEAL(Remove.)

WIRE TIES(with navigationsystem)

WIRE TIES WITH CLIPS (2)(without navigation system)

64. Route the XM radio harness and the DIN cablealong the vehicle harness toward the parkingbrake lever, and under the floor carpet. Secure theharness and DIN cable to the vehicle harness withfive wire ties in the areas shown.

2527072MWIRE TIES (5)

XM RADIO HARNESSAND DIN CABLE

67. Route the XM radio harness and DIN cable upalong the vehicle harness, and into the trunk.

Without Navigation System:

• Remove the two black seals from the body.

• Attach two wire ties with clips to the radioharness and DIN cable near the body holes.

• Insert the wire tie clips into the holes in thebody, and secure the lower portion with threeadditional wire ties.

• Reinstall the spacer.

With Navigation System:

• Secure the XM radio harness and DIN cable tothe vehicle harness with five wire ties in theareas shown.

• Reinstall the spacer.


Installing the Antenna

68. Get the antenna kit. Using isopropyl alcohol on ashop towel, clean the bottom of the antenna.Remove the adhesive backing from the fastener,and attach the fastener to the bottom of theantenna.

69. Route the antenna cable through the high mountbrake light opening, and install the antenna ontothe rear tray in the area shown. Attach onecushion tape to the edge of the high mount brakeopening where the cable touches it.

70. Align the antenna cable on the rear tray with thebrake light case, then using a felt-tip pen, markthe cable position on the edge of the case.

71. Measure the cutting area on the brake light case.Using a felt-tip pen, mark the area shown. Using autility knife, cut out the brake light case in thearea shown. Remove any burrs from the edges ofthe groove. Route the antenna cable through thegroove in the high mount brake light case, andreinstall the brake light case.

72. Route the antenna cable along the vehicleharness, and secure it to the vehicle harness withseven wire ties in the areas shown.

2620010M

WIRE TIES (7)

ANTENNA CABLE

VEHICLE HARNESS

CUSHIONTAPE

ANTENNAClean withisopropyl alcohol

ADHESIVEBACKING

FASTENER

REAR TRAY

20 mm

FELT-TIP PEN

REARTRAY

ANTENNACABLE

BRAKE LIGHTCASE

MARK

Align.

Straight.

ANTENNA CABLE

Cut.

BRAKE LIGHTCASE

5 mm10 mm

MARK

ANTENAClean withisopropyl alcohol.


73. Secure the antenna cable, the DIN cable, and theXM radio harness with three wire ties with clips.Insert the clips on the wire ties into the panelholes.

74. Using scissors, cut out the shaded areas from thetemplate.

75. Position the template on the right trunk side panel,and tape the template in place. While wearing eyeprotection, center punch the three cross marks onthe template.

76. Remove the template. Place a shop towel on theinside of the right trunk side panel to collect anymetal shavings.

2527100M

TEMPLATE

Cut shadedareas.

2620050M

ANTENNACABLE

RADIOHARNESS

WIRE TIE WITH CLIP

2527110M

CENTER PUNCH TEMPLATE

MASKINGTAPE

RIGHT TRUNKSIDE PANEL

CROSS MARKS (3)

2527121M

VINYL TAPE

8 mm DRILL BIT

10 mm

SHOPTOWEL

DIN CABLEANTENNACABLE

77. Drill three 8 mm holes through the inner panel:

• Wrap vinyl tape around the drill bit 10 mm fromthe end, or attach a drill stop.

• While wearing eye protection, drill an 8 mmhole through each center-punched mark.

• Remove all burrs and metal shavings, andapply touch-up paint to the edges of eachdrilled hole.

• Remove and discard the shop towel.


2527131M

4 x 8 mmWASHER SCREWS (4)FRONT UNIT

BRACKET

REAR UNITBRACKET

RECEIVERUNIT

4 mm FLANGENUTS (4)

2621031M

CUSHION TAPE

PANEL HOLE

ANTENNA CABLEAND DIN CABLE

WIRE TIEWITH CLIP

CUSHIONTAPES

2621020M

6 x 12 mmWASHER-BOLTS (3)

DRILLED HOLES (3)

RECEIVER UNIT

78. Install the front and rear unit brackets to thereceiver unit using two 4 x 8 mm washer-screwsand two 4 mm flange nuts for each bracket.

79. Position the receiver unit between the right trunkside panel and the rear fender panel, and plug inthe antenna cable connectors, the DIN cableconnector, and the XM radio harness connectorusing the panel hole to access the receiver unit.

80. Attach the receiver unit to the body panel usingthree 6 x 12 mm washer-bolts. Tighten the boltssecurely.

81. Attach two cushion tapes to the edges of thepanel in the areas shown.

82. Inside the fender area, fold the excess antennacable and DIN cable, and secure them with onewire tie with clip to the hole in the rear unitbracket.

83. Wrap the ends of the antenna cable and the DINcable with two cushion tapes.

2621010M

ANTENNA CABLE

DIN CABLE

XM RADIOHARNESS

RECEIVERUNIT

FENDERPANEL

RIGHT TRUNKSIDE PANEL

PANEL HOLE


2219090T

No. 33

FUSE BOX COVER

5A FUSE LABEL

2219080T

FUSE (5A)

FUSE BOX

84. Install the 5A fuse (provided) into the No. 33 slotof the fuse box.

85. Attach the 5A fuse label over the No. 33 positionon the fuse box cover.

86. Check that all wire harnesses and cables arerouted properly and all connectors are plugged in.

87. Reinstall all removed parts. Check that all clipsand fasteners are installed securely.

88. Reconnect the negative cable to the battery.

89. Enter the radio anti-theft code, and reset thecustomer's radio station presets.

90. Set the clock.

91. Set one of the radio station presets to FM 88.7and check the operation of the XM radio. Ifnecessary, use the XM radio Owner’s Manualsupplied.

NOTE: Whenever the battery is disconnected, thedriver’s window AUTO up function is disabled.

92. Do the driver's window AUTO up procedure:

• Start the engine. Push down on the driver’swindow switch until the window is fully open.

• Pull up on the driver’s window switch to closethe window completely, and hold the switch for2 seconds.

• Test the window AUTO up function.

aii30280 xm radio system - honda · receiver unit display module antenna xm radio harness fm...

Documents