ahcmom302a - perform machinery...
TRANSCRIPT
GREAT SOUTHERN INSTITUTE OF TECHNOLOGY
AHCMOM302A - Perform machinery maintenance
AHCMOM302A - Perform machinery maintenance
Page 1 of 60
AHCMOM302A - Perform machinery maintenance
This document has been created for trainers by trainers with financial assistance from the National VET E-Learning Strategy. The content has been developed and presented with respect to the required elements of the unit and follows the required outcomes of the training package. Any lecturer or trainer is able to use all or any of the following content for their own training needs or modify all or any of the content for their training needs. All images may be used by the trainer or they may substitute for their own as needed.
For more information or clarification, please contact Andrew Morrison at the Great Southern Institute of Technology (Albany, Western Australia) by emailing [email protected] (Project Manager).
AHCMOM302A - Perform machinery maintenance
Page 2 of 60
TABLE OF CONTENTS
Element 1.1 ........................................................................................................................................................................................................................................................... 3
Element 1.2 ........................................................................................................................................................................................................................................................... 8
Element 1.3, 1.4 .................................................................................................................................................................................................................................................. 14
Element 1.5 ......................................................................................................................................................................................................................................................... 18
Element 2.1 ......................................................................................................................................................................................................................................................... 22
Element 2.2 ......................................................................................................................................................................................................................................................... 25
Element 2.3, 2.4 .................................................................................................................................................................................................................................................. 29
Element 2.5 ......................................................................................................................................................................................................................................................... 33
Element 3.1 ......................................................................................................................................................................................................................................................... 36
Element 3.2 ......................................................................................................................................................................................................................................................... 39
Element 3.3 ......................................................................................................................................................................................................................................................... 42
Element 3.4 ......................................................................................................................................................................................................................................................... 46
Element 3.5 ......................................................................................................................................................................................................................................................... 50
Element 3.6 ......................................................................................................................................................................................................................................................... 54
Element 4.1, 4.2& 4.3 .......................................................................................................................................................................................................................................... 57
AHCMOM302A - Perform machinery maintenance
Page 3 of 60
Element 1.1 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 1 Carry out engine/equipment checks
Criteria Criteria 1: Timed and regular engine equipment checks are carried out on specialised machinery and equipment as specified in operator manuals
AHCMOM302A - Perform machinery maintenance
Page 4 of 60
Preventative maintenance
Written Content A well thought out machinery maintenance plan extends the working life of machines by
Reducing down time and cost to do repairs
Improving efficiency by having the machines starting and working well
Keeping up resale value of machinery Maintenance Schedules and Record Keeping Keep records for each machine to make sure these maintenance procedures are being performed at the proper time. These records will also help you predict parts inventory needs. If you keep a stock of required maintenance parts, such as filters, belts and seals, you won’t be caught in a situation where important maintenance was not performed on schedule because of lack of parts.
Images
Caption: Equipment checks should be performed regularly
AHCMOM302A - Perform machinery maintenance
Page 5 of 60
Pre operational checks for a 4 stroke lawnmower
Written Content The pre-operational checks for a 4 stroke petrol engine driven lawnmower include: • Check engine oil • Check fuel level • Check Blades for damage or excessive wear • Refuel in a well-ventilated area • Inspect Air cleaner • Inspect grass Bag • Set cutting height
The maintenance schedule for each machine appears in the manual.
Images
The manual provides all manufacturers recommendations.
AHCMOM302A - Perform machinery maintenance
Page 6 of 60
Safety-identify the risk, make the changes
Written Content Prior to carrying out maintenance on any machine a risk analysis and the identification of potential hazards need to be undertaken. Potential hazards and or precautions when servicing lawnmower include:
Use precaution when lifting the machine into position for a service
Use only the correct tools for the job. Injury can occur when tools slip or break.
Fuel leaks or fuel discharge from the filler cap are a fire risk.
Oil spills and leaks may result in slips and spills.
Stop the engine and disconnect the spark plug cap: Before checking, cleaning or working on the lawn mower.
If lawn mower starts to vibrate abnormally, check immediately.
Do not change the engine governor setting or over-speed the engine.
Do not start the engine when standing in front of the discharge opening..
Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
Allow the engine to cool before undertaking repairs or service.
To reduce the fire hazard, keep the engine, muffler, battery compartment (if applicable) and petrol storage area free of grass, leaves or excessive grease.
Images
Caption: Potential hazards are identified checking mower blades for wear and correct fit
AHCMOM302A - Perform machinery maintenance
Page 7 of 60
Assessment Question No 1 English
Question Timed and regular checks of machines are important because: 1. You can tell if a worker is being rough on a machine 2. The machines can get stolen or lost 3. To prevent breakdowns by finding faulty parts before they cause too much damage 4. Running motors with low oil levels reduces engine life 5. All operators should be aware of the safety instructions in the manual
Answer 3,4
Assessment Question No 2 English
Question A regular check of a 4stroke petrol motor driven lawnmower would not include: 1. Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition 2. Check engine oil level 3. Remove fuel tank and drain 4. Keep the engine, muffler and petrol tank free of grass, leaves or excessive grease. 5. Walk around the mower and check for any fuel or oil spills
Answers 3
AHCMOM302A - Perform machinery maintenance
Page 8 of 60
Element 1.2 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 1 Carry out engine/equipment checks
Criteria Criteria 2: All relevant grease or lubricant points are lubricated according to manufacturer specifications
AHCMOM302A - Perform machinery maintenance
Page 9 of 60
Identifying the lubrication points
Written Content Lubrication points and grease nipples can be found by:
Checking the operation and maintenance manual
Asking your supervisor and looking on the machine.
Images
Caption: cover manual
AHCMOM302A - Perform machinery maintenance
Page 10 of 60
General properties of a lubricating oil
Written Content Viscosity indicates the resistance of a liquid to flow. It describes whether oil is thick or thin. Other properties of oils include
Flash Point
Oxidation Stability
Acidity and Alkalinity (Total Acid Number and Total Base Number)
Detergency
Anti-rust Property
Corrosion Inhibition
Anti-foaming Property
Emulsification and Demulsification
Anti-wear Property
Extreme Pressure Loading Property (EP)
Tackiness Use the recommended oil and change the oil according to the manufacturer’s instructions. Oil loses many of its lubrication qualities with age and use.
Images
Caption: Oil Properties are identified on the label
AHCMOM302A - Perform machinery maintenance
Page 11 of 60
Viscosity of oil
Written Content Viscosity indicates the resistance of a liquid to flow. SAE viscosity ratings SAE (Society of Automotive Engineers) ratings designate the oil’s viscosity; simply put, how thick or thin oil is at a certain temperature. For example SAE 30 oil is “thinner” (less viscous) than SAE 50 oil. The vast majority of carmakers specify multi grade oils which are designed to act like a thin oil when cold so that they can circulate through the engine quickly on start up, and like a thicker oil when hot, to provide the necessary engine protection. An example of a multi grade oil designation is 10W-40. The 10W (W = winter) indicates how the oil would behave when cold, while the 40 is how it acts when hot. Oil with higher viscosity is thick and can stand greater pressure without being squeezed out of the lubricating surfaces. Higher viscosity oils such as SAE 90 are used in gearboxes. Lower viscosity oil is thin and penetrates tight bearings and moving parts. Low viscosity oil have a low number (SAE 10) Low viscosity oil offers less resistance to the moving parts. It is therefore important to use lubricating oil of appropriate viscosity to achieve optimum lubrication effect. The recommended oil is stated in the machine manual. For small 4 stroke motors SAE 10W-30 is recommended for general use in Australia.
Images
Caption: Checking oil
AHCMOM302A - Perform machinery maintenance
Page 12 of 60
General properties grease
Written Content Grease is a semi-solid formed by the dispersion of a thickening agent in a liquid lubricant (base oil). Greases have advantage over oil in some applications because greases stay at the point of lubrication and will hardly be squeezed out. Sometimes, greases can also be used to seal up machine parts to prevent the entry of moisture and dust.
Images
Caption: Grease gun
AHCMOM302A - Perform machinery maintenance
Page 13 of 60
Assessment Question No 1 English
Question Which single statement about viscosity is correct: 1. Viscosity and flash point are the same thing in oils 2. Corrosion inhibition and viscosity are the most important properties of oil 3. Lawnmower motors require oils with a viscosity of 90 SAE 4. Viscosity indicates the resistance to flow of a liquid
Answer 4
Assessment Question No 2 English
Question The recommended oil for a small 4stroke motor is: 1. SAE 125 gear oil 2. SAE 10W-30 3. SAE 5
Answers 2
Assessment Question No 3 English
Question Oil loses many of its lubrication qualities with age and use True False
Answers True
AHCMOM302A - Perform machinery maintenance
Page 14 of 60
Element 1.3, 1.4 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 1 Carry out engine/equipment checks
Criteria Criteria 3: Oils and filters are changed at intervals prescribed in operator manuals Criteria 4: Hydraulic hoses and systems checked for deterioration and defects actioned in line with supervisor's instructions
AHCMOM302A - Perform machinery maintenance
Page 15 of 60
Interval for oil and air filter changes
Written Content The manual prescribes the interval for oil and air filter changes Examples The recommendations for the air cleaner for a Honda lawn mower are:
Check each use
Clean every 3 months or 50 hours and
Replace when damaged or broken The manual recommendation for the oil filter on a Briggs & Stratton 4 stroke petrol motor (Model 210000) as drives a chipper shredder is:
Replace every 50 hours of use. If the air cleaner is not serviced according to the manufacturer’s recommendation and is used clogged or dirty, damage to the motor will occur. A dirty air cleaner will restrict air flow to the carburettor, reducing engine performance. Operating the engine without an air filter or damaged filters, will allow dirt to enter the engine, causing rapid engine wear If the oil and or oil filter are not changed as frequently as recommended then the oil can
Lose its lubrication and anti-oxidation properties
Cause corrosion and wear due to acidification of the oil
Cause corrosion and wear due to impurities being carried in the oil
Images
Caption: Replace air cleaner when damaged or broken
AHCMOM302A - Perform machinery maintenance
Page 16 of 60
Hydraulic Hose Inspection
Written Content It is important to inspect hydraulic hoses regularly. They are often subject to extreme conditions such as:
Pressure differentials during operation.
Exposure to weather, sun, chemicals,
Very warm storage conditions
Mishandling during operation or maintenance. These conditions can cause damage or premature deterioration. Identify the hoses on your machine and inspect them for signs of deterioration or damage. Make sure hoses are properly routed and protected from abrasion. Before disconnecting or performing any work on hydraulic system, all pressure in the system must be relieved by stopping the engine and lowering or supporting the implement. Keep body and hands away from pinhole leaks or nozzles that eject hydraulic fluid under high pressure. Use paper or cardboard, not hands, to search for leaks. Hydraulic fluid escaping under pressure can have sufficient force to penetrate the skin and do serious damage. If fluid is injected into the skin, it must be surgically removed within a few hours by a doctor familiar with this type of injury or gangrene may result.
Images
Caption: Inspect hydraulic hoses regularly
AHCMOM302A - Perform machinery maintenance
Page 17 of 60
Assessment Question No 1 English
Question If the air cleaner is not serviced according to the manufacturer’s recommendation and is used clogged or dirty, the motor will: 1. continue to run well 2. overheat 3. be damaged due to reduced air flow 4. be hard to start
Answers 3
Assessment Question No 2 English
Question If the oil and or oil filter are not changed as frequently as recommended then, the oil will 1. Lose its lubrication and anti-oxidation properties 2. Cause corrosion and wear due to acidification 3. Be fine as long as it is topped up regularly 4. Cause corrosion and wear due to impurities being carried in the oil 5. Overheat and cause a fire
Answers 1,2,4.
Assessment Question No 3 English
Question Check hydraulic hoses while they are working because: 1. They do not work very often 2. It is easy to find leaks by feeling with your hands 3. It is easier to see any potential leaks 4. Never because pin hole leaks or nozzles eject hydraulic fluid under high pressure. 5. Every day things change
Answers 3
AHCMOM302A - Perform machinery maintenance
Page 18 of 60
Element 1.5 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 1 Carry out engine/equipment checks
Criteria Criteria 5: Occupational Health and Safety (OHS) hazards are identified, risks assessed and risk controls are implemented
AHCMOM302A - Perform machinery maintenance
Page 19 of 60
Occupational health and safety act 1984 and regulations 1996
Written Content Occupational health and safety act 1984 and regulations 1996 require all hazards are identified and risks assessed. Prior to operating any machine a risk analysis and the identification of potential hazards need to be undertaken. Potential hazards when using a lawnmower include: • Never operate the lawn mower with defective guards or shields. • Use extreme caution when pulling the lawn mower toward you. • Stop the engine and disconnect the spark plug cap: -
• Before clearing a blockage or unclogging the lawn mower. • Before checking, cleaning or working on the lawn mower.
• Inspect the lawn mower for damage and make repairs before restarting and operating the lawn mower. • If lawn mower starts to vibrate abnormally, check immediately. • Do not change the engine governor setting or over-speed the engine. • Start the engine carefully according to the instructions and with feet well away from the blades. • Do not start the engine when standing in front of the discharge opening. • Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. • Stop the engine:
• Whenever you leave the lawn mower. • Before refuelling the lawn mower.
• Reduce the throttle setting during engine shut down and turn the fuel valve off at the conclusion of mowing. • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. • Allow the engine to cool before storing in any enclosure. • To reduce the fire hazard, keep the engine, muffler and petrol storage area free of grass, leaves or excessive grease.
Images
Caption: Safety First
AHCMOM302A - Perform machinery maintenance
Page 20 of 60
Potential hazards
Written Content Potential hazards when using a chainsaw include:
Use caution when handling fuel. Move the chainsaw at least 10 feet (3 m) from the fuelling point before starting the engine.
Do not allow other persons to be near the chainsaw when starting or cutting with the chainsaw. Keep bystanders and animals out of the work area.
Do not start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree.
Keep all parts of your body away from the saw chain when the engine is running.
Before you start the engine, make sure that the saw chain is not contacting anything.
Carry the chainsaw with the engine stopped, the guide bar and saw chain to the rear, and the muffler away from your body.
Do not operate a chainsaw that is damaged, improperly adjusted, or not completely and securely assembled. Be sure that the saw chain stops moving when the throttle trigger is released.
Shut off the engine before setting the chainsaw down.
Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance.
When cutting a limb that is under tension be alert for spring back so that you will not be struck when the tension in the wood fibres is released.
Keep the handles dry, clean, and free of oil or fuel mixture.
Operate the chainsaw only in well-ventilated areas.
Do not operate a chainsaw in a tree unless you have been specifically trained to do so.
All chainsaw service, other than the items listed in the Owner’s Manual maintenance instructions, should be performed by competent chainsaw service personnel.(For example, if improper tools are used to remove the flywheel or if an improper tool is used to hold the flywheel in order to remove the clutch, structural damage to the flywheel could occur and could be subsequently cause the flywheel to burst).
When transporting your chainsaw, use the appropriate chain guard (scabbard). Other important safety precautions are contained in the body of the Owner’s Manual.
Images
Caption: Wear Correct PPE when using chainsaws
AHCMOM302A - Perform machinery maintenance
Page 21 of 60
Assessment Question No 1 English
Question To reduce the risk of fire when using a lawnmower you should: 1. Never play with matches 2. Keep all nuts, bolts and screws tight 3. Leave the engine running when you refuel the motor 4. Do not put hands or feet near or under rotating parts 5. Keep the engine, muffler and petrol storage area free of grass, leaves or excessive grease 6. Stop the mower if it starts vibrating abnormally
Answer 5
AHCMOM302A - Perform machinery maintenance
Page 22 of 60
Element 2.1 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 2 Carry out transmission checks
Criteria Criteria 1: Drive and steering clutches are checked for operation and adjustment in line with operator manual
AHCMOM302A - Perform machinery maintenance
Page 23 of 60
transmission checks
Written Content Drive clutches Ride on and self-propelled mowers may have a clutch fitted to the drive shaft. The clutch allows the operator to engage and disengage the drive. Thus the clutch allows the operating part of the machine to be disengaged without turning off the motor. You may be familiar with the reel mower pictured. This mower has a clutch. To check the clutch. Operate the mower and ensure the drive fully engages. The recommended service requirements are in the machinery manual and are as follows. The cylinder clutch lever must have a 3-5 mm spacing from the end of the clutch gate when fully engaged. The adjustment bolts are at the bottom of the rod. Slip clutches PTO driven attachments such as a slasher or rotary hoe have slip clutches. These are a safety feature designed to prevent overload and should not be adjusted under general service. The clutch should be inspected looking for worn or faulty parts.
Images
Caption: Inspecting drive clutch on a reel mower
AHCMOM302A - Perform machinery maintenance
Page 24 of 60
Assessment Question No 1 English
Question Drive clutches are useful because 1. If a mower has a drive clutch it is able to handle tougher conditions 2. When you are driving you can take fewer breaks 3. They allow the operator to engage and disengage the working parts 4. There is no need to start the motor as often 5. They provide an additional lubrication point
Answer 3
AHCMOM302A - Perform machinery maintenance
Page 25 of 60
Element 2.2 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 2Carry out transmission checks
Criteria Criteria 2: Transmission oil levels are checked in line with operator manual
AHCMOM302A - Perform machinery maintenance
Page 26 of 60
Transmission/gear Oil levels
Written Content If gear oil is not changed according to the manufacturers instruction excessive wear and early breakdown of gears can result Continued reliability, successful operation and long life of power transmission equipment largely depend upon the constant supply of lubrication oil of proper quantity, quality and condition. The lifeline of the gearbox is its lubrication system, critical for supporting the drive under all modes of operation. Transmission and gearboxes are either filled to the dipstick mark or have an oil level plug. Use only oils as recommended by the manufacturer. Transmission oils require good
Film strength to prevent metal contact and scoring between the gear teeth.
Lubricity to reduce friction
Adhesion to prevent throw off associated with gravity or centrifugal force. Different machines require different transmission oils. The Power take off rotary hoe transmission should be topped up with oil (SAE 140) weekly and drained flushed and filled with new oil every 500 hours. Instruction for the maintenance of the transmission of a “Parklands” ride on mower includes:
Drain and refill Transmission Oil yearly – use one pint of SAE 30
Grease all pivots daily
Images
Caption: Show oil levels
AHCMOM302A - Perform machinery maintenance
Page 27 of 60
Automatic transmission fluid (ATF)
Written Content Automatic transmission fluid (ATF) is the fluid used in vehicles with automatic transmissions. It has very low viscosity (is a thin oil) and typically coloured red or green to distinguish it from motor oil and other fluids in the vehicle. On most vehicles its level is checked by a dipstick while the engine is running. Automatic transmission fluid must not be used in gearboxes The fluid is highly specialised oil optimised for the special requirements of a transmission, such as valve operation, brake band friction and the torque converter as well as gear lubrication.
Images
Caption: Transmission oil for Automatic vehicles
AHCMOM302A - Perform machinery maintenance
Page 28 of 60
Assessment Question No 1 English
Question If gear oil is not changed according to the manufacturers instruction 1. Excessive wear and early breakdown of gears can result. 2. Owners save money because the recommendation is aimed at selling more oil 3. The gears produce a burning smell and can cause fire 4. The owners warranty is voided
Answer 1,4
AHCMOM302A - Perform machinery maintenance
Page 29 of 60
Element 2.3, 2.4 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 2 Carry out transmission checks
Criteria Criteria 3: Tracks/wheels and undercarriage are checked for oil leaks and wear Criteria 4: Faulty seals or leaks are identified and corrective actions taken according to operator's instructions
AHCMOM302A - Perform machinery maintenance
Page 30 of 60
Tracks/wheels and undercarriage are checked for oil leaks and wear
Written Content When checking the undercarriage of a mini digger things to check are:
Loose bolts.
Oil leaks
Stiff or frozen track components
Tyre pressure in the wheels.
Check on the bolts to see if they are complete and tightly bolted
Make sure that the tension of the tracks is neither too tight nor too loose: refer to the manual. When checking under any machine operators must be aware of the risks of crushing if the machine falls.
Never jack up a mini-digger to check the undercarriage.
Never check under a machine with the engine running
Never walk or stand under a raised implement such as the bucket of a loader
Keep all bystanders well away from the machine while checking the undercarriage
Images
Caption: Checking Tyre pressure in the wheels
AHCMOM302A - Perform machinery maintenance
Page 31 of 60
Faulty seals or leaks are identified and corrective actions taken according to operator's instructions
Written Content Faulty seals or leaks are identified by leaking oil. The oil attracts dirt and dust and this can be easily seen. There may be a pool of oil left under the machine when parked overnight. If there appears to be a faulty seal it needs to be reported to your supervisor. The replacement of seals can be a major operation and is best undertaken by a mechanic. In most cases oil leaks need to be reported to the supervisor. In instances where the solution is simple such as, the drain plug is incorrectly fitted or loose the remedy should be undertaken immediately. Faulty seals allow water, dirt and other impurities to penetrate the bearing, transmission or engine. This will damage moving parts and cause undue wear.
Images
Caption: Check for oil Leaks
AHCMOM302A - Perform machinery maintenance
Page 32 of 60
Assessment Question No 2 English
Question Signs of faulty seals or oil leaks on a small machine include which of the following: 1. The engine vibrates excessively 2. Oil on the floor under the machine 3. The paint peels and blisters 4. The oil level requires regular top up 5. A dirt oil mixture gathers around the seal
Answer 2,4,5
Assessment Question No 3 English
Question When checking the tracks of a mini digger which of the following should be checked: 1. Are there any stiff or frozen track components 2. Drive the machine at full speed, jump off and run alongside to check everything is OK 3. Tyre pressure in the wheels. 4. All bolts to see if they are complete and tightly bolted 5. Jack the machine up and check the running of the tracks 6. Make sure that the tension of the tracks is neither too tight nor too loose
Answer 1,3,4,6
Assessment Question No 1 English
Question Which of the following is not a precaution to avoid the crushing hazard if the machine falls? 1. Never jack up a mini-digger to check the undercarriage. 2. Check on the bolts to see if they are complete and tightly bolted 3. Never check under a machine with the engine running 4. Never walk or stand under a raised implement such as the bucket of a loader 5. Keep all bystanders well away from the machine while checking the undercarriage
Answer 2
AHCMOM302A - Perform machinery maintenance
Page 33 of 60
Element 2.5 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 2 Carry out transmission checks
Criteria Criteria 5: Machine is regularly cleaned as an integral part of maintenance checks
AHCMOM302A - Perform machinery maintenance
Page 34 of 60
Put a here
Written Content Washing down the machine provides the opportunity to inspect moving parts and identify leaking seals and excessive wear. Regular cleaning of the machine will be part of the maintenance schedule. Lawnmowers, rotary hoes, mulchers and other garden machines should be cleaned at the end of each day’s use. Cleaning can be done using compressed air and wiping down with a soft cloth. Pressure cleaning using degreaser and high pressure water is used on machines with heavy soiling of oil and grease. When pressure cleaning all electrical parts need to be protected as water can cause the electrics to short out. Alternators and starter motors are particularly prone to water damage
Images
Caption: Washing down the machine provides the opportunity to inspect moving parts
AHCMOM302A - Perform machinery maintenance
Page 35 of 60
Assessment Question No 1 English
Question When washing down machines with water which of the following precautions must be taken 1. Take care and wear appropriate footwear on wet surfaces 2. Cover electrical components such as the starter motor or alternator. 3. Avoid washing off oil and grease 4. Wear the following PPE, a respirator and a welding mask
Answer 1,2,
AHCMOM302A - Perform machinery maintenance
Page 36 of 60
Element 3.1 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 3 Maintain components and attachments
Criteria Criteria 1: Personal protective equipment (PPE) is selected, used and maintained according to procedures
AHCMOM302A - Perform machinery maintenance
Page 37 of 60
Personal protective equipment (PPE) is selected, used and maintained according to procedures
Written Content The type of personal protective equipment required varies depending on the job being done, the equipment used and the chemicals being used. Product labels are required by law to provide directions and list the PPE requirements. The product Material Data Safety Sheet (MSDS) also provides directions concerning the necessary level of protective equipment. Some workplaces will provide a worker induction and specify the requirements for PPE on each job. It is the obligation of the employer to provide a safe work environment. This includes the provision of all required PPE. If the required PPE is not available workers should not commence the task. Workers have the responsibility to work safely and to minimize danger to themselves and their fellow workers. Some workplaces provide Safe Operating Procedures information for tasks and machines. These contain information on the required PPE. If information on PPE is not available workers should consult with their supervisor before commencing the job.
Images
Caption: Safety Operating procedures
AHCMOM302A - Perform machinery maintenance
Page 38 of 60
Assessment Question No 1 English
Question Which of the following statements is/are True? 1. Product labels are required by law to provide directions and list the PPE requirements 2. If information on PPE is not available workers should do the job anyway 3. The type of personal protective equipment required varies depending on the job being done 4. If the required PPE is not available workers should not commence the task 5. Workers have the responsibility to minimize danger to themselves and their fellow workers.
Answer 1,3,4,5
AHCMOM302A - Perform machinery maintenance
Page 39 of 60
Element 3.2 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 3 Maintain components and attachments
Criteria Criteria 2: Machine operational replacement wear components are checked for wear and condition
AHCMOM302A - Perform machinery maintenance
Page 40 of 60
Regular checking of machines for worn or damaged parts
Written Content Machines need to be checked regularly for worn or damaged parts A prestart check will include a visual inspection of the machine looking for worn or loose parts. A prestart inspection will also include checking fuel and oil and the air filter Parts that wear on a rotary lawnmower are the cutter blades. These need to be checked and replaced regularly.
Images
Lawnmower Maintainence.wmv
Caption: Mower Service
AHCMOM302A - Perform machinery maintenance
Page 41 of 60
Assessment Question No 1 English
Question A prestart check includes: 1. The replacement of mower blades 2. A visual inspection of the machine looking for worn or loose parts 3. Checking the fuel and oil level 4. Checking the air filter 5. Notification to the bank to pay the bearer 6. Running your hands over hydraulic hoses to check for oil leaks with the motor running
Answer 2,3,4
AHCMOM302A - Perform machinery maintenance
Page 42 of 60
Element 3.3 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 3 Maintain components and attachments
Criteria Criteria 3:Worn or unserviceable replacement components are replaced as part of daily routines
AHCMOM302A - Perform machinery maintenance
Page 43 of 60
Replacing worn or damaged parts on a lawnmower
Written Content Replacing worn or damaged parts. When checking or replacing the blades on a slasher type lawnmower be aware of the following:
1. If you have removed the blade assembly, always use a torque wrench to reinstall. 2. Wear heavy gloves to protect your hands. 3. The blades can be sharpened if they are still in good condition or replaced if worn out. 4. Poor sharpening technique can lead to weakening the blades or imbalance or poor cutting. The blades must be sharpened
by trained staff, check with your supervisor. Steps to follow when checking, sharpening or removing lawnmower blades
1. Turn the fuel valve to the OFF position. 2. Disconnect the spark plug cap, then tilt the mower to the right side, so the carburettor side is up. 3. Hold the blade disc firmly and remove the blade disc holder bolt. Set a flat blade screwdriver at the engine’s bolt to
prevent the blade disc from turning when removing the blade disc holder bolt. 4. Remove the blade setting bolts, blades, spring washers, blade washers and self-lock nuts from the blade disc.
Images
Caption: Inspect blades for damage
AHCMOM302A - Perform machinery maintenance
Page 44 of 60
Lawnmower repairs – Installation of blades
Written Content Installation: 1. Clean dirt and grass from the blades, blade disc and the inside on the cutter housing. 2. Install the blade, spring washers, blade washers and self-lock nuts to the blade disc using the blade setting bolt as described
below. 3. Tighten the self-lock nuts with a torque wrench. Prevent the blade disc from turning when tightening the self-lock nuts; tighten
the self-lock nuts to the specified torque. The blade setting bolts are specially designed for the mower. Should you ever have to replace them, use only genuine parts.
4. Install the blade/blade disc, washers and blade disc holder bolts. 5. Hold the blade disc firmly and install the blade disc holder bolts. 6. After installing the blade/blade disc check that it does not interfere with the housing.
Images
Caption: Keep mower blades clean
AHCMOM302A - Perform machinery maintenance
Page 45 of 60
Assessment Question No 1 English
Question Which of the following statements is True 1. The blades can be removed with the motor running 2. The blades can be sharpened if they are still in good condition 3. Poor sharpening technique can lead to weakening the blades and/or poor cutting 4. Mower blades should only be changed every three(3) years 5. To save time do not clean out the dirt and grass from the blades
Answer 2,3
AHCMOM302A - Perform machinery maintenance
Page 46 of 60
Element 3.4 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 3 Maintain components and attachments
Criteria Criteria 4: Component inspection and replacement activities are completed safely following enterprise and industry guidelines
AHCMOM302A - Perform machinery maintenance
Page 47 of 60
Safe Work Practices
Written Content The safe completion of repairs to equipment requires workers to follow the enterprise guidelines. These guidelines are provided on Safe Operating Procedures information sheets, in workshop and machinery manuals and in induction manuals. Workers should follow these three steps in all aspects of their work.
Identify the hazard
Assess the risk
Report hazard to your supervisor
Make the changes
Images
Caption: Spot the hazard, Solve the problem, Make the changes,
AHCMOM302A - Perform machinery maintenance
Page 48 of 60
Safety guidelines
Written Content To check, repair or replace lawnmower blades safely follow these guidelines:
Read and understand the Owner’s Manual.
Before using, always visually inspect to see that the blade, blade bolt(s) and mower housing are not worn or damaged. Replace worn or damaged blade and bolt(s) in sets to preserve balance.
Never pick up or carry a lawn mower while the engine is running.
Stop the engine and disconnect the spark plug cap: - Before clearing a blockage or unclogging the lawn mower. - Before checking, cleaning or working on the lawn mower. –
After striking a foreign object. Inspect the lawn mower for damage and make repairs before restarting and operating the lawn mower. –
If lawn mower starts to vibrate abnormally, check immediately.
To reduce the fire hazard, keep the engine, muffler, battery compartment (if applicable) and petrol storage area free of grass, leaves or excessive grease.
Replace worn or damaged parts for safety.
Images
Caption: Job Safety
AHCMOM302A - Perform machinery maintenance
Page 49 of 60
Assessment Question No 1 English
Question Safety guidelines covering the repairs and maintenance of machines can be found in which of the following 1. Phantom comics 2. Safe Operating Procedures information sheets, 3. Workshop and machinery manuals 4. Induction manuals. 5. Newspapers
Answer 2,3,4
AHCMOM302A - Perform machinery maintenance
Page 50 of 60
Element 3.5 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 3 Maintain components and attachments
Criteria Criteria 5: Moving operational components are checked for wear and condition and adjusted to the tolerances specified in operator manuals where applicable
AHCMOM302A - Perform machinery maintenance
Page 51 of 60
Inspecting and servicing Belts
Written Content Ensure engine is shut down and all parts have stopped moving before doing any belt inspections or replacements. The maintenance schedule for belts will be outlined in the machinery manual. Some general rules are: All belts should be inspected at the prestart check Replace belts if they are badly cracked, frayed, rotten or damaged. Broken belts can result in:
A rapid increase in temperature and warning light flashing in the case of a fan belt.
Drive chain not operating in the case of a drive belt
No power steering
Images
Caption: Fan Belt
AHCMOM302A - Perform machinery maintenance
Page 52 of 60
Front tine tiller -Belt removal and replacement Page No: 3
Written Content Belt removal and replacement for a Front Tine Tiller The tiller has been engineered with belts made of special material (Kevlar Tensile). They should not be replaced with an off-the-shelf belt. Disconnect and ground the spark plug wire against the engine. 1. Remove the belt cover from the left side of the tiller as follows. 2. Remove two self-tapping screws and flat washers from the front of belt cover. 3. Remove the hex stop nut and flat washer from the side of the belt cover. Remove belt cover 4. Lift the belt off the transmission pulley 5. Remove the hex nut which secures the reverse idler pulley to the idler bracket. Slide idler pulley out and remove the belt. 6. Reassemble the new belt, following instructions in reverse order. Make certain the reverse drive belt is assembled with the wide side of the belt against the transmission and engine pulleys. Belt tension: Be certain to adjust the clutch control as instructed in the final clutch adjustment section of assembly instructions. The belt tension is adjusted on the cable attached to the tine engagement handle and carried out after the belt has been installed. Refer to your machinery manual when adjusting belt tension.
Images
Caption : belt cover
AHCMOM302A - Perform machinery maintenance
Page 53 of 60
Assessment Question No 1 English
Question Which of the following are False 1. All belts should be inspected at the prestart check 2. Replace belts if they are badly cracked, frayed, rotten or damaged. 3. All belts should be checked with the motor running 4. All belts should be as tight as possible 5. Belts should not be used to tie up pets
Answer 1,2,5
AHCMOM302A - Perform machinery maintenance
Page 54 of 60
Element 3.6 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 3 Maintain components and attachments
Criteria Criteria 6: Work areas are cleaned, returned to operating condition and maintained according to enterprise and OHS requirements
AHCMOM302A - Perform machinery maintenance
Page 55 of 60
Put a here
Written Content Workshop areas must be kept clean and tidy
Put all tools in their proper place
Remove rubbish and broken or replaced parts and packaging
Wipe down benches and sweep floors
Remove any spilt oil, grease or fuel
All machines are stored in their allocated place
Machines returned to the workshop must be cleaned
Images
Caption: Clean Work Shop
AHCMOM302A - Perform machinery maintenance
Page 56 of 60
Assessment Question No 1 English
Question Which of the following are true? An untidy workshop is:
1. Efficient because tools are easier to find 2. Dangerous there are slips and trips hazards 3. More efficient when you are short of time 4. OK if you have plenty of room 5. Hard to keep clean
Answer 2,5
AHCMOM302A - Perform machinery maintenance
Page 57 of 60
Element 4.1, 4.2& 4.3 Module Information
Developers Applied Quality Training Fundamentals (AQTF)
Competency This unit covers the process of maintaining machinery and equipment that is used principally in agriculture, horticulture, and conservation and land management work and defines the standard required to:
carry out engine/equipment checks according to operator manuals and enterprise requirements
carry out lubrication and replacement of oils and filters according to operator manuals
carry out transmission checks, including drive and steering clutches and oil levels
check machinery and equipment components for wear and tear, and replace, tag and report defects if necessary
dispose of replaced parts and oils according to legislation and enterprise procedures
and record all details of maintenance and requirements for monitoring
Element 4 Record maintenance
Criteria Criteria 1: Identified faults and defects are recorded in machine record. Criteria 2: Maintenance procedures including duplicates usage are recorded in workshop record Criteria 3: Service or repair requirements are reported and actioned according to prescribed procedures
AHCMOM302A - Perform machinery maintenance
Page 58 of 60
Maintenance Records
Written Content The importance of records Maintenance records are written notes that provide documentation about the upkeep of a certain piece of equipment. These records are useful in maintenance management because
They help businesses ensure their equipment is kept in good condition.
They provide businesses with a way to manage and track repair and preventative upkeep expenses.
They can help make sure that any appropriate equipment maintenance or plant maintenance has been completed so that plant operations will run smoothly
They help avoid accidents or plant shut-downs resulting from defective equipment.
Images
Caption: Fill in Record Form
AHCMOM302A - Perform machinery maintenance
Page 59 of 60
Recording Maintenance
Written Content Machine and workshop logs need to be filled out after any maintenance or parts replacement is carried out on machinery. Check with your supervisor/workshop manager if you cannot locate logs or record books. Key components of the records include:
1. Any faults that need repair 2. Faults that have been repaired 3. Preventative service and maintenance carried out 4. Work done by each machine is recorded daily
Images
Caption: Work shop log book
AHCMOM302A - Perform machinery maintenance
Page 60 of 60
Assessment Question No 1 English
Question Maintenance records are important because they 1. Help avoid accidents 2. Provide information on the parts used 3. Can be used to check on workers 4. Provide businesses with a way to manage and track repair and preventative upkeep expenses. 5. Provide business with a way to check on poor or rough operators
Answer 1,2,4.