Agriair 1000-3 HO & 1000-3 HO 230VOperation and Maintenance Manual

®

CONFORMS TO UL STD 507CERTIFIED TO CAN/CSA STDC22.2 NO. 113-M1984

WARNINGDo not use with combustible or explosive material. Do not expose to water or rain. Connect only to grounded outlet with GFCI device. Disconnect power for cleaning and servicing. This equipment to be operated only by trained personnel. High intensity Ultraviolet light. Avoid eye and skin exposure. Do not operate without coverings. Do not look directly at UV light source. Wear UV eye protection.

Safety Warning Instructions:READ AND SAVE THESE INSTRUCTIONS

This equipment to be operated only by trained personnel.

Do not use with combustible or explosive material.

Do not expose to water or rain.

Connect only to grounded outlet with GFCI device.

Disconnect power for cleaning and servicing.

Do not operate if cord or plug is damaged. Contact a authorized service facility for examination and/or repair.

Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traf-

fic areas and where it is not a tripping hazard.

High intensity Ultraviolet light inside. Avoid eye and skin exposure.

Do not look directly at UV light source. Wear UV eye protection.

Do not operate without coverings.

Avertissement de sécurité Instructions:LIRE ET CONSERVER CES INSTRUCTIONS

Cet équipement doit être utilisé que par un personnel formé.

Ne pas utiliser avec des matières combustibles ou explosives.

Ne pas exposer à l’eau ou à la pluie.

Connectez uniquement à une prise mise à la terre avec un dispositif GFCI.

Coupez l’alimentation électrique pour le nettoyage et l’entretien.

Ne pas utiliser si le cordon ou la fiche est endommagé. Contactez un centre de service autorisé pour examen et / ou réparation.

Ne pas passer le cordon sous un tapis. Ne pas couvrir le cordon avec des carpettes, les coureurs, ou revêtements similaires. Éloi-

gner le cordon des endroits passants et où il n’est pas un risque de déclenchement.

Haute intensité de lumière ultraviolette à l’intérieur. Évitez les yeux et l’exposition de la peau.

Ne pas regarder directement à la source de lumière UV. Porter des lunettes de protection UV.

Ne pas faire fonctionner sans revêtement.

The AgriAir 1000-3 HO air purifier uses photo hydro ionization (PHI) technology to generate friendly oxidizer plasma which seeks and destroys odors and bio-contaminants at their source, in indoor commercial cultivation facilities. Our energy efficient purifier produces and distributes oxidizer plasma naturally generated from humidity and oxygen in the surrounding area. The 1000-3 HO is sized to sanitize environments 5,000-12,000 cubic feet of flowering, drying and packaging rooms, without the use of chemicals or ozone. It’s portable, easy to install, scalable and ready to plug-in and go.

Agriair 1000-3 HO SpecificationsAirflow: 300 - 650 CFM, variable speed blowerPower Requirements: 115 VAC/60 Hz/3 amps; 230 VAC/50-60 Hz/1.3 ampsIO Generators: (2) 14” IO generator cellsFiltration: 16”x24”x2” MERV 11 pleated filter; 16”x24”x1” pleated carbon filterRecessed Controls: ON/OFF switch, variable speed control, (2) hour meters, (2) ON/OFF generator switchesHousing: aluminum housing with 12” outlet and (2) rubber handlesExhaust Collar: 12” diameterSize/Weight with Filters: 14 W x 20”H x 27”L, 40 lbs.

Receiving InstructionsVisually inspect the unit for damage. Ensure that the filters have not been dislodged during shipping. The unit must be operated with filters in place.

Operation of the Agriair 1000-3 HOThe Agriair 1000-3 HO machine purifies air passing through the unit and disperses eco-friendly oxidizer plasma to purify surrounding air and surfaces. The oxidizer plasma, generated from O2 and humidity in the air, remains active for about 15 minutes then converts back to O2 and humidity. Generation of oxidizer plasma could be set with Gen 1, Gen 2 or with both turned to the ON position, depending on the size of the room and the sanitizing requirements. The airflow through the 1000-3 HO unit is adjustable by the speed controller between 300 and 650 CFM.

Operating Instructions1) Turn the blower On by turning the Speed Controller knob to the desired airflow.2) Select Gen 1 or Gen 2 depending on the size of space and the level of contamination. Each of the Generators cover up to 8000 cf in flowering rooms. Use both for spaces up to 12,000 cf or rapid clean up.3) The green LED light will illuminate when the generator is operating. The running time of each generator is measured by separate Hour Meters.

Application ExamplesFor an occupied room, 20’x25’x10’ (5000 cubic ft), the generator output should be set with one generator on. For coverage of up to 12,000 cf, use both generators.

Prefilter Replacement1. Unplug the unit and remove the filter protection gate.2. Remove the used filter and install a new filter.3. Slide the gate back into the track for closure.

Generator Cell ReplacementThe generator cell’s output slowly degrades and should be replaced after 25,000 hours of running. To replace the generator cell(s):1) Unplug the machine.2) Remove the 12 screws holding the side panel.3) Unplug the power supply connector and remove 4 screws while holding the generator.4) Remove the whole generator from the unit and follow the instructions included with the replacement cell.

Ordering Info Part # Agriair 1000-3 HO AAHPG1000-3 HO

Agriair 1000-3 HO 230 AAHPG1000-3 HO-230

MERV 11 Pleated Filter OPF2416

Carbon Filter OG2416D

Quick Clamp, 12”-16” Dia. QCW14

Flexible Duct, Wire & Fiber Reinforced, 12” Dia. x 25’ L OAD12R

Agriair 14” Replacement Generator Cell EHPG-4

4640 Campus Place, Suite 100T. 425.290.3922 | F. 425.290.3964

Wiring DiagramDRAWN BY: REV

SCALE DATE SHEET

A. Briceno A

Not to Scale Nobember 9, 2018

MODEL

Diagram Legend

Terminated (Capped) Wire

Wiring Connector

Red LED LightR

Green LED LightG

Amber LED LightA

115 or 230VAC

50-60hzON/OFFSWITCH

GEN 1 POWERSUPPLY

GEN 1HOURMETER

GEN1

AAHPG1000-3HO & AAHPG1000-3HO-230

1 of 1

SPEEDCONTROLLER

ECOFIT2RREu45MOTOR

6 or 25 μFCAPACITOR

BROWN

BLUEBLACK

GREEN

GREEN

WHITE

GREEN

WHITE

GEN 1ON/OFFSWITCH

GEN 2 POWERSUPPLY

GEN 2HOURMETER

GEN2

GEN 2ON/OFFSWITCH

OMNITEC DESIGN LIMITED WARRANTY

Omnitec Design warrants, for a period of twelve (12) months from the date of purchase, that all Products, component parts and accessories, excluding filters, will be free from defects in material and workmanship under normal use and service.

THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS F.O.B., Omnitec Design 4640 Campus Place Ste. 100, Mukilteo, WA 98275 Phone: 425-290-3922

In order to keep this warranty in effect for the aforementioned twelve-month period, the purchaser must (i) promptly, i.e., immediately upon discovery, inform Omnitec Design’s customer service of any defects, and (ii) properly use and maintain the Product prior to the discovery of any defect.

This warranty does not cover normal wear and tear or defects caused by (i) improper or negligent handling or unauthorized modifications; (ii) defective or improper premises, chemical, or electrical influences; or (iii) weather or other forces of nature.

In order to provide the best customer service possible, Omnitec Design requests that purchaser completes the enclosed LIMITED WARRANTY REGISTRATION FORM and returns it to Omnitec Design within 30 days of purchase date.

LIMITATIONS OF WARRANTYTHIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER WARRANTIES AND OBLIGATIONS OF Omnitec Design OR ITS SUPPLIERS, EXPRESS OR IMPLIED, AND Omnitec Design EXPRESSLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

LIMITATION OF REMEDYUnder no circumstances shall Omnitec Design or any supplier of Omnitec Design be liable for any loss or damage, including, but not limited to, loss or damage arising out of the failure of the Products to operate for any period of time, inconvenience, the use of rental or replacement equipment, loss of profits or other economic loss, or general, direct, special, indirect, incidental or consequential damages or property damages.

PRODUCT SUITABILITYMany states and localities have their own varied codes and regulations governing sales, construction, installation, and/or use of Products for certain purposes. While Omnitec Design attempts to assure that its Products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the Products are installed or used. Omnitec Design recommends that, before purchasing and using a Product, purchasers review the Product application, and federal, state and local regulations, to be sure that the Products, installation, and use will comply with them.

www.agriairequipment.com 425-290-3922Omnitec Design 4640 Campus Place Ste. 100 Mukilteo, WA 98275

Agriair® RETURN POLICY

Omnitec Design, the manufacturer of the Agriair® , guaranties that the equipment will function properly, to our specifications and will be repaired if necessary at no charge for a period of 1 year (See our warranty policy for details). All equipment returned to us for repairs or exchange requires an RMA number for processing and tracking.

All Agriair® & IO technology has been tested by independent labs and in several indoor grow facilities, proving the performance as described in our literature. Our air purification equipment is a powerful tool to help purify your environment yet, we cannot guaranty that under your operating conditions and procedures, the results will be the same as experienced by other growers.

If you are not satisfied with the purchase or the operation of our equipment, it can be returned under the following conditions:

If the equipment was un-used and was returned within 14 days. The customer will be charged return freight* and an additional 10% of the purchase price as a restocking fee.

Iftheequipmentwasusedandisworkingperourspecifications:Within the first 30 days of receipt, the customer will be charged return freight* and 20% of the purchase price for refurbishing. Within the first 31-60 days of receipt, the customer will be charged return freight* and 30% of the purchase price for refurbishing. Within the first 61-90 days of receipt, the customer will be charged return freight* and 40% of the purchase price for refurbishing.

After 90 days, returns will not accepted.

For returns, repairs or technical support please contact us via email at orders@agriairequipment.com or call (425) 290-3922 for further assistance.

*Please save the original packing to insure possible trouble-free returns and additional fees.

page 1

®