adsp-bf609 ezkit man rev 1-0 march 2012
DESCRIPTION
ADSP ManualTRANSCRIPT
a
ADSP-BF609 EZ-KIT Lite®
Evaluation System Manual
Revision 1.0, March 2012
Part Number82-000269-01
Analog Devices, Inc.One Technology WayNorwood, Mass. 02062-9106
Copyright Information© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-ment may not be reproduced in any form without prior, express written consent from Analog Devices, Inc.
Printed in the USA.
DisclaimerAnalog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by impli-cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark NoticeThe Analog Devices logo, Blackfin, CrossCore, EZ-Board, EZ-Extender, and EZ-KIT Lite are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of their respective owners.
Regulatory Compliance The ADSP-BF609 EZ-KIT Lite is designed to be used solely in a labora-tory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity. This board should not be used in or near any medical equipment or RF devices.
The ADSP-BF609 EZ-KIT Lite is currently being processed for certifica-tion that it complies with the essential requirements of the European EMC directive 2004/108/EC and therefore carries the “CE” mark.
The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent dam-age may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused EZ-KIT Lite boards in the protective shipping package.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Product Overview .......................................................................... xii
Purpose of This Manual .................................................................. xv
Intended Audience .......................................................................... xv
Manual Contents ........................................................................... xvi
What’s New in This Manual ........................................................... xvi
Technical or Customer Support ..................................................... xvii
Supported Processors ..................................................................... xvii
Product Information .................................................................... xviii
Analog Devices Web Site ........................................................ xviii
EngineerZone ......................................................................... xviii
Related Documents ........................................................................ xix
Notation Conventions ..................................................................... xx
USING ADSP-BF609 EZ-KIT LITE
Package Contents .......................................................................... 1-2
ADSP-BF609 EZ-Board ................................................................ 1-3
Default Configuration ................................................................... 1-3
Supported Operating Systems ....................................................... 1-5
Contents
vi ADSP-BF609 EZ-KIT Lite Evaluation System Manual
System Requirements .................................................................... 1-5
EZ-KIT Lite Installation ............................................................... 1-6
EZ-KIT Lite Session Startup ......................................................... 1-7
Evaluation License Restrictions ................................................... 1-10
Memory Map ............................................................................. 1-10
DDR2 SDRAM .......................................................................... 1-12
SPI Interface .............................................................................. 1-13
SMC Interface ............................................................................ 1-13
Ethernet Interface ....................................................................... 1-13
USB OTG HS Interface .............................................................. 1-14
CAN Interface ............................................................................ 1-14
UART Interface .......................................................................... 1-15
SD Interface ............................................................................... 1-16
Rotary Encoder Interface ............................................................ 1-16
Temperature Sensor Interface ...................................................... 1-17
Link Ports Interface .................................................................... 1-17
General-Purpose I/O (GPIO) ...................................................... 1-18
JTAG Interface ........................................................................... 1-18
Power-On-Self Test ..................................................................... 1-20
Expansion Interface III ............................................................... 1-20
Power Architecture ..................................................................... 1-21
Power Measurements .................................................................. 1-21
Example Programs ...................................................................... 1-22
Reference Design Information ..................................................... 1-22
ADSP-BF609 EZ-KIT Lite Evaluation System Manual vii
Contents
ADSP-BF609 EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Software-Controlled Switches (SoftConfig) .................................... 2-3
Overview of SoftConfig ........................................................... 2-3
SoftConfig on the ADSP-BF609 EZ-KIT LITE ...................... 2-7
Programming SoftConfig Switches ........................................... 2-8
Push Buttons and Switches .......................................................... 2-17
JTAG Interface Switches (SW1, SW3–5) ................................ 2-18
Boot Mode Select Switch (SW2) ............................................ 2-19
IRQ/Flag Enable Switches (SW6–7) ....................................... 2-20
Reset Switch (SW8) ............................................................... 2-20
Rotary Encoder With Momentary Switch (SW9) .................... 2-20
Wake Push Switch (SW10) .................................................... 2-21
Power Jumpers ............................................................................ 2-21
LEDs .......................................................................................... 2-22
GPIO LEDs (LED1–4) ......................................................... 2-23
Thermal Limit LED (LED5) ................................................. 2-23
Power LED (LED6) ............................................................... 2-23
Reset LED (LED7) ................................................................ 2-24
SPD LED (LED6) ................................................................. 2-24
Connectors .. ............................................................................... 2-24
DCE UART Connector (J2) .................................................. 2-25
Link Port /JTAG Connectors (J3 and P8) ............................... 2-25
JTAG Connector (P1) ........................................................... 2-25
Contents
viii ADSP-BF609 EZ-KIT Lite Evaluation System Manual
JTAG Connector (ZP1) ......................................................... 2-26
Expansion Interface III Connectors (P1A–C, P2A, P3A) ........ 2-26
USB Connector (P7) ............................................................. 2-26
Power Connector (P18) ......................................................... 2-26
CAN Connector (J4) ............................................................ 2-27
SD Connector (J5) ................................................................ 2-27
Ethernet Connector (J1) ....................................................... 2-27
Ethernet Connectors (P16-17) ............................................... 2-27
ADSP-BF609 EZ-KIT LITE BILL OF MATERIALS
ADSP-BF609 EZ-KIT LITE SCHEMATIC
Title Page ..................................................................................... B-1
Processor DDR2 Interface ............................................................ B-2
Processor Signals ........................................................................... B-3
Processor Power and Ground ......................................................... B-4
Temp Sensor, Boot Switch, DSP CLK, USB Conn ......................... B-5
Memory ....................................................................................... B-6
UART0 ........................................................................................ B-7
CAN and Rotary Encoder ............................................................. B-8
Ethernet ....................................................................................... B-9
JTAG, Link Port 0 and 1 ........................................................... B-10
Push Buttons, Reset, LEDs ......................................................... B-11
SoftConfig Switches, IO Extender ICs ......................................... B-12
Expansion Interface, Page 1 ........................................................ B-13
ADSP-BF609 EZ-KIT Lite Evaluation System Manual ix
Contents
Expansion Interface, Page 2 ........................................................ B-14
Expansion Interface, Page 3 ........................................................ B-15
Power ........................................................................................ B-16
INDEX
Contents
x ADSP-BF609 EZ-KIT Lite Evaluation System Manual
ADSP-BF609 EZ-KIT Lite Evaluation System Manual xi
PREFACE
Thank you for purchasing the ADSP-BF609 EZ-KIT Lite®, Analog Devices, Inc. low-cost evaluation system for the ADSP-BF60x Blackfin® processors.
The ADSP-BF609 processor is a member of the Blackfin family of prod-ucts, incorporating the Analog Devices/Intel Micro Signal Architecture (MSA). Blackfin processors combine a dual-MAC state-of-the-art signal processing engine, the advantages of a clean, orthogonal RISC-like micro-processor instruction set, and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture.
ADSP-BF60x Blackfin processors embody a new type of embedded pro-cessor designed specifically to meet the computational demands and power constraints of today’s automotive systems, embedded industrial, instrumentation, and power/motor control applications.
The evaluation board is designed to be used in conjunction with the CrossCore® Embedded Studio (CCES) development tools to test capabil-ities of the ADSP-BF60x Blackfin processors. The CCES development environment aids advanced application code development and debug, such as:
• Create, compile, assemble, and link application programs written in C++, C, and assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory
Product Overview
xii ADSP-BF609 EZ-KIT Lite Evaluation System Manual
• Read and write core and peripheral registers
• Plot memory
Access to the processor from a personal computer (PC) is achieved through a USB port (when a debug agent is mounted on the EZ-KIT Lite board) or an external JTAG emulator. The USB interface provides unre-stricted access to the ADSP-BF609 processor and evaluation board peripherals. Analog Devices JTAG emulators offer faster communication between the host PC and target hardware. Analog Devices carries a wide range of in-circuit emulation products. To learn more about Analog Devices emulators and processor development tools, go to: http://www.analog.com/processors/tools/.
The ADSP-BF609 EZ-KIT Lite provides example programs to demon-strate the product capabilities.
The ADSP-BF609 EZ-KIT Lite software is part of the EZ-Board BSP (Board Support Package) for the Blackfin ADSP-BF60x family which needs to be installed after CrossCore Embedded Studio. The EZ-KIT Lite is a licensed product that offers an unrestricted evalu-ation license for 90 days after activation. For more information, refer to “Evaluation License Restrictions” on page 1-10 in this manual and the Installation Quick Reference Card.
Product OverviewThe board features:
• Analog Devices ADSP-BF609 Blackfin processor
• 349-pin LFBGA package
• 25 MHz CLKIN oscillator
• 48 MHz USB CLKIN
ADSP-BF609 EZ-KIT Lite Evaluation System Manual xiii
Preface
• Double Data Rate Synchronous Dynamic Random-Access Memory (DDR2 SDRAM)
• Micron MT47H64M16HR-3
• 64M x 16 bit (1 Gb)
• Burst flash memory
• Micron PC28F128P33T85B
• 16M x 16-bit (32 MB) flash memory
• Quad Serial Peripheral Interface (SPI)
• Winbond W25Q32
• 32 Mb serial flash memory
• Ethernet PHY
• National Semiconductor
• DP83848C 10/100 PHY
• Two LEDs integrated into the RJ-45 connector: link/activity
• Universal Asynchronous Receiver/Transmitter (UART)
• ADM3315 RS-232 line driver/receiver
• DB9 female connector
• Temp sensor
• On Semiconductor
• ADM1032 two-wire sensor
Product Overview
xiv ADSP-BF609 EZ-KIT Lite Evaluation System Manual
• Controller Area Network (CAN)
• NXP TJA1041
• RJ-11 connector
• Debug interface
• JTAG header for use with ADI emulators
• Standalone debug agent
• LEDs
• Eight LEDs: one power (green), one board reset (red), one temperature limit (amber), Ethernet speed (green), and four general-purpose (amber)
• Push buttons
• Four push buttons: one reset, one wake, and two IRQ/flag
• Expansion Interface 3 (EI3)
• Next generation of the expansion interface design, provides access to most of the processor signals
• Power supply
• CE approved
• 5V @ 3.6 Amps
• Other features
• Link port connectors
• SD/MMC memory connector
• Rotary encoder
• MP JTAG in and out connectors
• 0.05-ohm resistors for processor current measurement
ADSP-BF609 EZ-KIT Lite Evaluation System Manual xv
Preface
• JTAG ICE 14-pin header
• USB cable
Traditional mechanical switches for changing the board’s factory setup have been removed in favor of I2C controlled software switches. The only remaining mechanical switches are the JTAG switches, boot mode switch, and push buttons. The JTAG switches are provided for setting up sin-gle-processor JTAG communications or multiple-processor configurations.
For information about the hardware components of the EZ-KIT Lite, refer to “ADSP-BF609 EZ-KIT Lite Bill Of Materials” on page A-1.
Purpose of This ManualThe ADSP-BF609 EZ-KIT Lite Evaluation System Manual provides instructions for installing the product hardware (board). The text describes operation and configuration of the board components and pro-vides guidelines for running your own code on the ADSP-BF609 EZ-KIT Lite. Finally, a schematic and a bill of materials are provided for reference.
Intended AudienceThe primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture, instruction set, and C/C++ programming languages.
Programmers who are unfamiliar with Analog Devices processors can use this manual, but should supplement it with other texts (such as the ADSP-BF60x Blackfin Processor Hardware Reference and Blackfin Processor Programming Reference) that describe your target architecture.
Manual Contents
xvi ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Programmers who are unfamiliar with CrossCore Embedded Studio should refer to the CCES online help.
Manual ContentsThe manual consists of:
• Chapter 1, “Using ADSP-BF609 EZ-KIT Lite” on page 1-1.Describes EZ-KIT Lite functionality from a programmer’s perspec-tive and provides a simplified memory map of the processor.
• Chapter 2, “ADSP-BF609 EZ-KIT Lite Hardware Reference” on page 2-1.Provides information about the EZ-KIT Lite hardware components.
• Appendix A, “ADSP-BF609 EZ-KIT Lite Bill Of Materials” on page A-1.Provides a list of hardware components used to manufacture the EZ-KIT Lite board.
• Appendix B, “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1.Lists the resources for board-level debugging.
What’s New in This ManualThis is the first revision (Revision 1.0) of the ADSP-BF609 EZ-KIT Lite Evaluation System Manual.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual xvii
Preface
Technical or Customer SupportYou can reach Analog Devices, Inc. Customer Support in the following ways:
• Visit the Embedded Processing and DSP products Web site athttp://www.analog.com/processors/technical_support
• E-mail tools questions [email protected]
• E-mail processor questions [email protected] (World wide support)
[email protected] (China support)
• Phone questions to 1-800-ANALOGD
• Contact your Analog Devices, Inc. local sales office or authorized distributor
• Send questions by mail to:Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported ProcessorsThis evaluation system supports Analog Devices ADSP-BF609 Blackfin embedded processors.
Product Information
xviii ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Product InformationProduct information can be obtained from the Analog Devices Web site and the CCES online help system.
Analog Devices Web SiteThe Analog Devices Web site, www.analog.com, provides information about a broad range of products—analog integrated circuits, amplifiers, converters, and digital signal processors.
To access a complete technical library for each processor family, go to http://www.analog.com/processors/technical_library. The manuals selection opens a list of current manuals related to the product as well as a link to the previous revisions of the manuals. When locating your manual title, note a possible errata check mark next to the title that leads to the current correction report against the manual.
Also note, myAnalog.com is a free feature of the Analog Devices Web site that allows customization of a Web page to display only the latest infor-mation about products you are interested in. You can choose to receive weekly e-mail notifications containing updates to the Web pages that meet your interests, including documentation errata against all manuals. myAnalog.com provides access to books, application notes, data sheets, code examples, and more.
Visit myAnalog.com (found on the Analog Devices home page) to sign up. If you are a registered user, just log on. Your user name is your e-mail address.
EngineerZoneEngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search
ADSP-BF609 EZ-KIT Lite Evaluation System Manual xix
Preface
FAQs and technical information to get quick answers to your embedded processing and DSP design questions.
Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://ez.analog.com to sign up.
Related DocumentsFor additional information about the product, refer to the following publications.
Table 1. Related Processor Publications
Title Description
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Blackfin Dual Core Embedded Processor Data Sheet
General functional description, pinout, and timing of the processor
ADSP-BF60x Blackfin Processor Hardware Reference
Description of the internal processor archi-tecture and all register functions
Blackfin Processor Programming Reference Description of all allowed processor assembly instructions
Table 2. Related CCES Publications
Title Description
CrossCore Embedded Studio Assembler and Preprocessor Manual
Description of the assembler functions and commands
CrossCore Embedded Studio C/C++ Complier and Library Manual for Blackfin Processors
Description of the complier functions and commands for Blackfin processors
CrossCore Embedded Studio Linker and Utilities Manual
Description of the linker functions and com-mands
CrossCore Embedded Studio Loader and Utilities Manual
Description of the loader/splitter functions and commands
Notation Conventions
xx ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Notation ConventionsText conventions used in this manual are identified and described as follows.
Example Description
Close command (File menu)
Titles in reference sections indicate the location of an item within the CCES environment’s menu system (for example, the Close command appears on the File menu).
{this | that} Alternative required items in syntax descriptions appear within curly brackets and separated by vertical bars; read the example as this or that. One or the other is required.
[this | that] Optional items in syntax descriptions appear within brackets and sepa-rated by vertical bars; read the example as an optional this or that.
[this,…] Optional item lists in syntax descriptions appear within brackets delim-ited by commas and terminated with an ellipse; read the example as an optional comma-separated list of this.
.SECTION Commands, directives, keywords, and feature names are in text with letter gothic font.
filename Non-keyword placeholders appear in text with italic style format.
Note: For correct operation, ...A Note provides supplementary information on a related topic. In the online version of this book, the word Note appears instead of this
symbol.
Caution: Incorrect device operation may result if ...Caution: Device damage may result if ... A Caution identifies conditions or inappropriate usage of the product that could lead to undesirable results or product damage. In the online version of this book, the word Caution appears instead of this symbol.
Warning: Injury to device users may result if ... A Warning identifies conditions or inappropriate usage of the product that could lead to conditions that are potentially hazardous for the devices users. In the online version of this book, the word Warning appears instead of this symbol.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-1
1 USING ADSP-BF609 EZ-KIT LITE
This chapter provides information to assist you with development of pro-grams for the ADSP-BF609 EZ-KIT Lite evaluation system.
The following topics are covered.
• “Package Contents” on page 1-2
• “ADSP-BF609 EZ-Board” on page 1-3
• “Default Configuration” on page 1-3
• “Supported Operating Systems ” on page 1-5
• “System Requirements” on page 1-5
• “EZ-KIT Lite Installation” on page 1-6
• “EZ-KIT Lite Session Startup” on page 1-7
• “Evaluation License Restrictions” on page 1-10
• “Memory Map” on page 1-10
• “DDR2 SDRAM” on page 1-12
• “SMC Interface” on page 1-13
• “Ethernet Interface” on page 1-13
• “USB OTG HS Interface” on page 1-14
• “CAN Interface” on page 1-14
Package Contents
1-2 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
• “UART Interface” on page 1-15
• “Rotary Encoder Interface” on page 1-16
• “Temperature Sensor Interface” on page 1-17
• “Link Ports Interface” on page 1-17
• “General-Purpose I/O (GPIO)” on page 1-18
• “JTAG Interface” on page 1-18
• “Power-On-Self Test” on page 1-20
• “Expansion Interface III” on page 1-20
• “Power Architecture” on page 1-21
• “Power Measurements” on page 1-21
• “Example Programs” on page 1-22
• “Reference Design Information” on page 1-22
For information about the CCES graphical user interface (GUI), includ-ing the boot loading, target options, and other facilities of the EZ-KIT Lite system, refer to the online help.
For detailed information about the ADSP-BF609 Blackfin processor, see documents referred to as Related Documents.
Package ContentsYour ADSP-BF609 EZ-KIT Lite package contains the following items.
• ADSP-BF609 EZ-KIT Lite board
• Standalone debug agent (SADA2)
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-3
Using ADSP-BF609 EZ-KIT Lite
• USB cable
• 5 in 1 USB cable kit
• CE approved power supply
• Ethernet cable
• 2 GB memory card
• 4 nylon standoffs
• 4 nylon hex nuts
With the standalone debug agent removed, the board can connect to an Analog Devices emulator: USB, HP-USB, or ICE-100B.
Contact the vendor where you purchased your EZ-KIT Lite or contact Analog Devices, Inc. if any item is missing.
ADSP-BF609 EZ-BoardThe product ADSP-BF609 EZ-KIT Lite with the Stand Alone Debug Agent removed is referred to as the ADSP-BF609 EZ-Board®.
The EZ-Board requires an Analog Devices USB-based emulator (USB, HP-USB, or ICE-100B).
Default ConfigurationThe ADSP-BF609 EZ-KIT Lite board is designed to run as a standalone unit.
When removing the EZ-KIT Lite board from the package, handle the board carefully to avoid the discharge of static electricity, which can dam-age some components.
Default Configuration
1-4 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Figure 1-1 shows the default jumper and switch settings and LED used in installation. There are four nylon standoffs in a bag included in the box. They can be installed in the four corner mounting holes (MH1, MH7, MH8, MH9) if desired. Place the nylon standoff in the hole and tighten a hex nut on each. Confirm that your board is in the default configuration before using the board.
The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD precau-tions are recommended to avoid performance degradation or loss of function-ality. Store unused EZ-KIT Lite boards in the protective shipping package.
Figure 1-1. EZ-KIT Lite Hardware Setup
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-5
Using ADSP-BF609 EZ-KIT Lite
Supported Operating Systems CCES 1.0.0 is supported on the following operating systems:
• Windows® XP Professional SP3 (32-bit only)
• Windows Vista™ Business, Enterprise, or Ultimate SP2 (32-bit only)
• Windows 7 Professional, Enterprise, or Ultimate (32- and 64-bit)
Windows Vista and Windows 7 users may experience User Access Control (UAC) related errors if the software is installed into a pro-tected location, such as Program Files or Program Files (x86). We recommend installing the software in a non-UAC-protected location.
System RequirementsVerify that your PC has these minimum requirements for the CCSE 1.0.0 installation:
• 2 GHz single-core processor
• 1 GB RAM
• 8 GB available disk space
• One open USB port
A faster disk drive decreases the build time, especially for a large amount of source files.
EZ-KIT Lite Installation
1-6 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite InstallationFollow these instructions to ensure correct operation of the product soft-ware and hardware.
Step 1: Attach the provided USB plugs (labeled Mini and Male) to the pro-vided USB cable.
Step 2: Connect the EZ-KIT Lite board to a personal computer (PC) run-ning CCES.
There are two connection options: using an Analog Devices emulator or using the standalone debug agent.
Using an Emulator:
1. Plug one side of the assembled USB cable into the USB connector of the emulator. Plug the other side into a USB port of the PC run-ning CCES.
2. Attach the emulator to the header connector P1 (labeled JTAG) on the EZ-KIT Lite board.
Using the Debug Agent:
1. Attach the standalone debug agent to connectors P1 and ZP1 of the EZ-KIT Lite board.
2. Plug one side of the provided USB cable into the USB connector of the debug agent ZP1 (labeled USB). Plug the other side of the cable into a USB port of the PC running CCES.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-7
Using ADSP-BF609 EZ-KIT Lite
Step 3: Attach the provided cord and appropriate plug to the 5V power adaptor.
1. Plug the jack-end of the assembled power adaptor into the power connector P18 (labeled 5V) on the EZ-KIT Lite board.
2. Plug the other side of the power adaptor into a power outlet. The power LED (labeled LED6) lights green when power is applied to the board.
3. Power the emulator. Plug the jack-end of the assembled power adaptor into the emulator and plug the other side of the power adaptor into a power outlet. The ENABLE/POWER indicator lights green.
Step 4 (if connected through the debug agent): Verify that the yellow USB monitor LED and the green power LED on the debug agent are both on. This signifies that the board is communicating properly with the host PC and ready to run CCES.
EZ-KIT Lite Session StartupIt is assumed that the CrossCore Embedded Studio software is installed and running on your PC.
Note: If you connect the board or emulator first (before installing CCES) to the PC, the Windows driver wizard may not find the board drivers.
1. Navigate to the CCES environment via the Start menu.
Note that CCES is not connected to the target board.
EZ-KIT Lite Session Startup
1-8 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
2. Use a debug configuration to connect to the EZ-KIT Lite board.
If a debug configuration exists already, select the appropriate configuration and click Apply and Debug or Debug. Go to step 9.
To create a debug configuration:
• Click the down arrow next to the little bug icon, select Debug Configurations, or
• Choose Run > Debug Configurations.
3. (To create a new debug configuration) Select CrossCore Embed-ded Studio Application and click (New launch configuration).
The Select Processor page of the Session Wizard appears on the screen.
4. Ensure Blackfin is selected in Processor family. In Processor type, select ADSP-BF609. Click Next.
The Select Connection Type page of the Session Wizard appears on the screen.
5. Select one of the following:
• For standalone debug agent connections, EZ-KIT Lite and click Next.
• For emulator connections, Emulator and click Next.
The Select Platform page of the Session Wizard appears on the screen.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-9
Using ADSP-BF609 EZ-KIT Lite
6. Do one of the following:
• For standalone debug agent connections, ensure that the selected platform is ADSP-BF609 EZ-KIT Lite via Debug Agent.
• For emulator connections, choose the type of emulator that is connected to the board.
7. Click Finish to close the wizard.
The new debug configuration is created and added to the pro-gram(s) to load list.
8. In the Program(s) to load section, choose the program to load when connecting to the board. If not loading any program upon connection to the target, do not make any changes.
Note that while connected to the target, there is no way to choose a program to download. To load a program once connected, termi-nate the session.
To delete a configuration, go to the Debug Configurations dialog box and select the configuration to delete. Click and choose Yes when asked if you wish to delete the selected launch configuration. Then Close the dialog box.
To disconnect from the target board, click the terminate button (red box) or choose Run > Terminate.
To delete a session, choose Target > Session > Session List. Select the session name from the list and click Delete. Click OK.
Evaluation License Restrictions
1-10 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Evaluation License RestrictionsThe ADSP-BF609 EZ-KIT Lite software is part of the EZ-Board BSP (Board Support Package) for the Blackfin ADSP-BF60x family. The EZ-KIT Lite is a licensed product that offers an unrestricted evaluation license for 90 days after activation. Once the evaluation period ends, the evaluation license becomes permanently disabled. If the evaluation license is installed but not activated, it allows 10 days of unrestricted use and then becomes disabled. The license can be re-enabled by activation.
An evaluation license can be upgraded to a full license. Licenses can be purchased from:
• Analog Devices directly. Call (800) 262-5645 or 781-937-2384 or go to: http://www.analog.com/en/content/buy_online/fca.html.
• Analog Devices, Inc. local sales office or authorized distributor. To locate one, go to:http://www.analog.com/salesdir/continent.asp.
The EZ-KIT Lite hardware must be connected and powered up to use CCES with a valid evaluation or full license.
Memory MapThe ADSP-BF609 processor has a single unified 4G memory space for instructions and data storage. See Figure 1-2. The processor’s memory details can be found in the ADSP-BF60x Blackfin Processor Hardware Reference.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-11
Using ADSP-BF609 EZ-KIT Lite
Figure 1-2. ADSP-BF609 Processor Memory Map
DDR2 SDRAM
1-12 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
The board has a 16M x 16-bit burst flash memory connected to the pro-cessor’s Static Memory Controller (SMC). The processor also is connected to a 32 Mb quad serial flash memory via the Serial Peripheral Interface (SPI). Both flash memories can be used for non-volatile data storage and processor boot.
DDR2 SDRAMThe ADSP-BF609 processor connects to a 128 MB Micron MT47H64M16HR-3 chip through the Double Data Rate Synchronous Dynamic Random-Access Memory (DDR2 SDRAM) controller. The DDR2 memory controller on the processor and DDR2 memory chip are powered by the on-board 1.8V regulator. Data is transferred between the processor and DDR2 on both the rising and falling edges of the DDR2 clock. The DDR2 controller on the processor can operate at a maximum clock frequency of 250 MHz.
With a CCES session running and connected to the EZ-KIT Lite via the USB standalone debug agent, the DDR2 registers are configured automat-ically each time the processor is reset. The values are used whenever DDR2 is accessed through the debugger (for example, when viewing memory or loading a program).
To disable the automatic setting of the DDR2 registers, select Target Options from the Session menu in CCES and uncheck Use XML reset values.
An example program is included in the EZ-KIT Lite installation directory to demonstrate how to setup and access the DDR2 interface. For more information on how to initialize the registers after a reset, refer to the hardware reference manual.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-13
Using ADSP-BF609 EZ-KIT Lite
SPI InterfaceThe ADSP-BF609 processor has two SPI interfaces, SPI0 and SPI1. SPI0 is connected to a Winbond W25Q32BV 32 Mb serial flash memory with dual and quad SPI support.
Quad mode is enabled by default. The processor flag signals, PD00 and PD01 (SPI0 D2 and D3), can be disconnected by using SoftConfig. Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 for more infor-mation. By default, the SPI0 chip select 1 is connected to the memory device. This can also be disconnected by using SoftConfig.
SMC InterfaceThe Static Memory Controller (SMC) interface of the ADSP-BF609 EZ-KIT Lite contains a 32 MB (16M x 16) Numonyx PC28F128P33B parallel flash chip. Flash memory is connected to the 16-bit data bus and address lines 1–23. Chip enable is decoded by using SMC0_AMS0.
The flash memory is bottom boot and provides One-Time-Programmable (OTP) memory.
Flash memory is pre-loaded with boot code for the POST program. For more information, refer to “Power-On-Self Test” on page 1-20.
Ethernet InterfaceThe ADSP-BF609 processor has two Reduced Media Independent Inter-faces (RMIIs), one of which connects to an external Ethernet PHY device. The EZ-KIT Lite provides a National DP83848C, Auto-MDIX, fully compliant PHY with IEEE 802.2/802.2u standards. The PHY supports 10BASE-T and 100BASE-TX operations. The PHY and processor support IEEE 1588 time stamping, available on the EZ-KIT Lite via a standard
USB OTG HS Interface
1-14 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
RJ-45 connector. For more information, see “Ethernet Connector (J1)” on page 2-27.
The MAC address is stored in parallel flash (U44) at address 0x0106 0000, and can be found on a sticker on the bottom side of the board.
If a program is written over this area of the flash, the MAC address will be lost.
Example programs are included in the EZ-KIT Lite installation directory to demonstrate how to use the Ethernet interface.
USB OTG HS InterfaceThe ADSP-BF609 processor has an integrated USB PHY, and the EZ-KIT Lite provides a mini AB connector. A 48 MHz oscillator provides the clocking for the high-speed USB 2.0 On-the-Go (OTG) interface.
The board allows 5V at 500 mA to a peripheral by enabling the FET switch U50. The USB controller has native support for controlling the FET through the USB_VBC signal.
A test point also is provided for the USB clock input of the processor. A user can remove the series resistor and feed an external clock from a func-tion generator.
Use the example programs in the EZ-KIT Lite installation directory to learn about the processor’s device and host modes. For more information, refer to the ADSP-BF60x Blackfin Processor Hardware Reference.
CAN InterfaceThe Controller Area Network (CAN) interface of the EZ-KIT Lite is con-nected to the NXP TJA1041 high-speed CAN transceiver. The transceiver
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-15
Using ADSP-BF609 EZ-KIT Lite
is attached to the CAN0 port of the ADSP-BF609 processor via an RJ-11 connector. See “CAN Connector (J4)” on page 2-27.
The PE02 programmable flag connects to the error and power on indica-tion output of the CAN transceiver, CAN0. The transmit and receive pins of the transceiver are connected to the dedicated CAN0 transmit and receive pins of the processor.
To disconnect the CAN IC signals CAN0RX and CAN0_ERR, change the appropriate settings via SoftConfig. See “Software-Controlled Switches (SoftConfig)” on page 2-3.
Example programs are included in the EZ-KIT Lite installation directory to demonstrate CAN circuit operation.
UART InterfaceThe ADSP-BF609 processor has two built-in universal asynchronous transmitters (UARTs), with only UART0 connected to a UART line trans-mitter. UART0 has full RS-232 functionality via the Analog Devices ADM3315 line driver and receiver (U39).
Pin PD07/UART0_TX/TM0_ACI3 of the processor is connected to the ADM3315 device directly. Pin PD08/UART0_RX/TM0_ACI0 is connected as well by the default setting of SoftConfig. (This can be changed by the SoftConfig switch).
By default, UART0 RTS and CTS signals are not connected (but can be through SoftConfig). The SoftConfig switches also allow the loopback of CTS and RTS. UART CTS can be added as an input to the reset circuit through SoftConfig. Pins 1, 4 and 6 of the UART connector (J2) can be enabled as an input to the on-board reset circuit through SoftConfig.
Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 for more information.
SD Interface
1-16 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
An example program demonstrating UART0 in POST is included in the EZ-KIT Lite installation directory. Note that the loopback of TX and RX data is done through an external connector.
SD InterfaceThe ADSP-BF609 processor has a secure digital (SD) interface. The SD interface consists of a clock pin, command pin, card detect pin, write pro-tect pin, and an 8-bit data bus. SoftConfig controls the connection of processor pins PG10 and PG13 to the card detect and write protect features of the SD interface. Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 and “SD Connector (J5)” on page 2-27for more details.
An example program is included in the EZ-KIT Lite installation directory to demonstrate how to set up and access the SD interface.
Rotary Encoder InterfaceThe ADSP-BF609 processor has a built-in, up-down counter with support for a rotary encoder. The three-wire rotary encoder interface connects to the rotary switch (SW9). The rotary encoder can be turned clockwise for the up function, counter clockwise for the down function, or can be pushed towards the center of the board to clear the counter.
The rotary switch is a two-bit quadrature (gray code) counter with detent, meaning that both the down signal (CNT0_DG) and up signal (CNT0_UD) tog-gle when the count register increases on a rotation to the right. Upon rotating to the left, CNT0_DG and CNT0_UD toggle, and the overall count decreases.
If the processor pins are needed on the expansion interface III, disconnect the rotary encoder switch via SoftConfig. See “Software-Controlled Switches (SoftConfig)” on page 2-3 for details.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-17
Using ADSP-BF609 EZ-KIT Lite
An example program is included in the EZ-KIT Lite installation directory to demonstrate how to set up and access the rotary encoder.
Temperature Sensor InterfaceTwo external pins (SYS_TDA and SYS_TDK) of the processor are connected to an internal thermal diode. The EZ-KIT Lite uses ON Semiconductor ADM1032 digital thermometer and under/over temperature alarm to monitor the processor’s temperature as well as the thermal diodes inside the ADM1032 device. The thermometer uses the I2C bus and flag pins of the processor. The following software-controlled signals are used for tem-perature monitoring.
• TEMP_IRQ_EN (programmable flag pin PG9)
• TEMP_THERM_EN (programmable flag pin PB15)
The thermal limit flag is connected to an LED (LED5) for a visual alarm if the temp exceeds the limit. The thermal limit flag and ADM1032 IRQ connect to flag pins of the processor, but are nonessential for temperature monitoring. Consequently, the software-controlled switches have these signals disconnected from the ADSP-BF609 processor by default.
See “Thermal Limit LED (LED5)” on page 2-23 and “Software-Con-trolled Switches (SoftConfig)” on page 2-3 for more information.
Example programs are included in the EZ-KIT Lite installation directory to demonstrate temperature sensor operations.
Link Ports InterfaceThe ADSP-BF609 processor has four dedicated link ports. Each link port has a clock pin, an acknowledgment pin, and eight data pins. The ports can operate at up to 83 MHz and act as either a receiver or a transmitter.
General-Purpose I/O (GPIO)
1-18 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
The ports are used to interface gluelessly to other ADSP-BF609 processors which also have the link ports pins brought out.
The EZ-KIT Lite enables access to link ports 0 and 1 (referred to as LP0 and LP1 in schematics) via connectors P8 and J3, respectively. Two ADSP-BF609 EZ-KIT Lites can mate gluelessly via the link port connec-tors. The processors communicate via the link ports, all while performing independent tasks on each of the EZ-KIT Lite. To loopback the link port connectors on one EZ-KIT Lite or connect three or more EZ-KIT Lites, obtain a standard, off the shelf connector from Samtec. For more informa-tion, see “Link Port /JTAG Connectors (J3 and P8)” on page 2-25.
By default, the EZ-KIT Lite boots from the parallel flash memory. Link port 0 can be selected as the boot source by setting the boot mode select switch (SW2) to position 6. See “Boot Mode Select Switch (SW2)” on page 2-19.
General-Purpose I/O (GPIO)Four LEDs are available via programmable pins PG14, PG15, PE14, and PB11. The connections are on by default and can be shut off through SoftConfig.
Two push buttons are available on programmable flags PB10 and PE01. The push buttons are connected to the processor by default. Use SoftCon-fig to disconnect the push buttons. Refer to “Software-Controlled Switches (SoftConfig)” on page 2-3 for more information.
JTAG InterfaceThe EZ-KIT Lite design enables a multi-processor JTAG session using connectors P8 and J3. By default, the board is set up in single-processor mode. In single-processor mode, create a CCES session based on a stand-alone debug agent or an external emulator. To use the EZ-KIT Lite in
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-19
Using ADSP-BF609 EZ-KIT Lite
multi-processor mode, install an external emulator. Only one external emulator is required for the main EZ-KIT Lite; other EZ-KIT Lites in the JTAG chain do not require an emulator. In this mode, create a CCES platform based on the number of JTAG devices in the JTAG chain using the CCES Target Configurator. Then create a session for the EZ-KIT Lite based on the newly created platform.
For a dual ADSP-BF609 EZ-KIT Lite session, connect two EZ-KIT Lites via connectors J3 and P8. Flip one of the two EZ-KIT Lites by 180 degrees to allow the boards to mate. To switch between single- and multi-processor modes, use DIP switches SW1 and SW3-5. The switch set-tings can be found in “JTAG Interface Switches (SW1, SW3–5)” on page 2-18.
For three or more ADSP-BF609 EZ-KIT Lite sessions, connect each of the boards with JTAG cables. The cables connect JTAG pins of each board and put the EZ-KIT Lites in a JTAG serial chain. For three EZ-KIT Lites, three JTAG cables are required. Similarly, for four EZ-KIT Lites, four JTAG cables are required. Note that each respective EZ-KIT Lite board also requires its own power supply.
The standalone debug agent can be replaced by an external emulator, such as the Analog Devices high-performance USB-based emulator. Be careful not to damage the connectors when removing the debug agent. The emu-lator is connected to P1 on the top side of the board. See “EZ-KIT Lite Installation” on page 1-6 for more information.
Part numbers for Samtec standard, off the shelf link port cables can be found in “Link Port /JTAG Connectors (J3 and P8)” on page 2-25.
For more information about emulators, contact Analog Devices or go to:http://www.analog.com/en/processors-dsp/software-and-refer-
ence-designs/content/tools_product_overview/fca.html.
Power-On-Self Test
1-20 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Power-On-Self TestThe Power-On-Self-Test Program (POST) tests all EZ-KIT Lite peripher-als and validates functionality as well as connectivity to the processor. Once assembled, each EZ-KIT Lite if fully tested for an extended period of time with POST. All EZ-KIT Lite boards are shipped with POST pre-loaded into one of their on-board flash memories. The POST is executed by resetting the board and pressing the proper push button(s). The POST also can be used as a reference for a custom software design or hardware troubleshooting. Note that the source code for the POST program is included in the EZ-KIT Lite installation directory along with the readme.txt file, which describes how the board is configured to run POST.
Expansion Interface IIIThe Expansion Interface III (EI3) allows an Analog Devices EZ-Extender® or a custom-design daughter board to be tested across vari-ous hardware platforms that have the same expansion interface.
The EI3 implemented on the ADSP-BF609 EZ-KIT Lite consists of five connectors, P1A, P1B, P1C, P2A, and P3A. The connectors contain a major-ity of the processor's signals. For pinout information, go to “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1. The mechanical dimensions of the expansion connectors can be obtained by contacting “Technical or Cus-tomer Support”.
For more information about daughter boards, visit the Analog Devices Web site at:http://www.analog.com/en/processors-dsp/Blackfin/proces-
sors/Blackfin_evaluation_kits/fca.html.
Limits to current and interface speed must be taken into consideration when using the EI3. Current for the EI3 can be sourced from the EZ-KIT
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 1-21
Using ADSP-BF609 EZ-KIT Lite
Lite; therefore, the current should be limited to 200 mA for 5V and 300 mA for the 3.3V planes. If more current is required, then a separate power connector and a regulator must be designed on the daughter card. Additional circuitry can add extra loading to signals, decreasing their max-imum effective speed.
Analog Devices does not support and is not responsible for the effects of additional circuitry.
Power ArchitectureThe ADSP-BF609 EZ-KIT Lite has three primary voltage domains: 3.3V, 1.25V and 1.8V.
The Analog Devices ADP1864 controller provides 3.3V for the VDD_USB, VDD_EXT, and the 3.3V power requirements of the board. The Analog Devices ADP1715 regulator provides 1.8V for VDD_DMC. The processor’s VDD_INT is regulated to 1.25V by the ADP2119 controller.
Power MeasurementsLocations are provided for measuring the current draw from various power planes. Precision 0.05 ohm shunt resistors are available on the VDD_EXT, VDD_INT, VDD_DDR2, VDD_USB, 3.3V, and USB_VBUS voltage domains. For current draw, the jumper is removed, voltage across the resistor can be measured using an oscilloscope, and the value of the resistor can be mea-sured using a precision multi-meter. Once voltage and resistance are measured, the current can be calculated by dividing the voltage by the resistance. For the highest accuracy, a differential probe should be used for measuring the voltage across the resistor. For more information, refer to “Power Jumpers” on page 2-21.
Example Programs
1-22 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Example ProgramsExample programs are provided with the ADSP-BF609 EZ-KIT Lite to demonstrate various capabilities of the product. The programs are installed with CCES and can be found in the CrossCore Embedded Stu-dio directory. Refer to a readme file provided with each example for more information.
Reference Design InformationA reference design info package is available for download on the Analog Devices Web site. The package provides information on the design, lay-out, fabrication, and assembly of the EZ-KIT Lite.
The information can be found at:http://www.analog.com/en/processors-dsp/blackfin/proces-
sors/board-design-database/resources/index.html.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-1
2 ADSP-BF609 EZ-KIT LITE HARDWARE REFERENCE
This chapter describes the hardware design of the ADSP-BF609 EZ-KIT Lite board.
The following topics are covered.
• “System Architecture” on page 2-2Describes the board’s configuration and explains how the board components interface with the processor.
• “Software-Controlled Switches (SoftConfig)” on page 2-3Lists and describes the processor signals routed through the soft-ware-controlled switches.
• “Push Buttons and Switches” on page 2-17Shows the locations and describes the push buttons and switches.
• “Power Jumpers” on page 2-21Shows the locations and describes the configuration jumpers.
• “LEDs” on page 2-22Shows the locations and describes the LEDs.
• “Connectors” on page 2-24Shows the locations and provides part numbers for the on-board connectors. In addition, the manufacturer and part number infor-mation is provided for the mating parts.
System Architecture
2-2 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
System ArchitectureThis section describes the processor’s configuration on the EZ-KIT Lite board (Figure 2-1).
The EZ-KIT Lite is designed to demonstrate the ADSP-BF609 Blackfin processor’s capabilities.
The clock rate can be set up on the fly by the processor. The input clock is 25 MHz. The core clock runs at a maximum of 500 MHz. The default boot mode for the processor is parallel flash boot. See “Boot Mode Select Switch (SW2)” on page 2-19 for information on how to change the default boot mode.
Figure 2-1. EZ-KIT Lite Block Diagram
ADSP-BF609500 MHz
Dual Core349-lead LFBGA
0.80mm 19x19mm pkg
JTAGPort
25 MHz Oscillator
PowerRegulation
SMC0
32 MBBurst Flash(16M x 16 )
CLK
JTAGConn
Quad SPIFlash32Mb
ADM3315
RS232DB9Conn
5VPWR
IN
3.30V (Adjustable)
1.25V (Adjustable)
Expansion Interface III
PBs/LEDs
ExtClock
Test Point/Crystal
128 MB DDR2
(64M x 16)
DDR2
USB OTGCircuitry
EthernetRMIIPHY
SD/MMCConn
RotaryEncoder
Conn
ADM1032Temp
Sensor
CANRJ11Conn
TJA 1041Transceiver
10/100MAC SPI
RJ45CONN
USB MiniConn U
SB
2.0
(HS
)
Tem
pS
enso
r /TW
I
MM
CR
SI
GPCOUNTER GPIOs CAN
2.0 UART
Link
Por
ts
1.80V (Adjustable)
Ser
ial
Por
tsE
PPI
Ports
Link Port 0/ MPJTAG Out
Conn
DIPSWTs
Link Port 1 / MPJTAG In
Conn
EPPIs
UART
SPI
Power
ACM PWM
TWI
EBIU
Serial Ports
GPIOs
USB
C
LK
48 MHz Oscillator
ExtClock
Test Point/Crystal
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-3
ADSP-BF609 EZ-KIT Lite Hardware Reference
Software-Controlled Switches (SoftConfig)
On the ADSP-BF609 EZ-KIT Lite, most of the traditional mechanical switches have been replaced by I2C software-controlled switches. The remaining mechanical switches are provided for setting up a single- or multiprocessor JTAG session, changing the boot mode, and push buttons. Reference any SoftConfig*.c file found in the installation directory of CCES for an example of how to set up the SoftConfig feature of the ADSP-BF609 EZ-KIT Lite through software.
The SoftConfig section of this manual serves as a reference to any user that intends to modify an existing software example. If software provided from ADI is used there should be little need to reference this section.
Care should be taken when changing SoftConfig settings not to create a conflict with interfaces. This is especially true when con-necting extender cards. There is one possible conflict on the EZ-KIT Lite when using SoftConfig—the wake push button must be disconnected when using the SD card interface. The wake push button is disabled by default, but if making changes, the signal ~WAKE_PUSHBUTTON_EN must be set to high if the SD card function is desired.
Overview of SoftConfigIn order to further clarify the use of electronic single FET switches and multi-channel bus switches, an example of each is illustrated and com-pared to a traditional mechanical switching solution. This is a generic example that uses the same FET and bus switch components that are on the EZ-KIT Lite. After this generic discussion there is a detailed explana-tion of the SoftConfig interface specific to the ADSP-BF609 EZ-KIT Lite.
Software-Controlled Switches (SoftConfig)
2-4 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Figure 2-2 shows two individual FET switches (Pericom PI3A125CEX) with reference designators UA and UB. Net names ENABLE_A and ENABLE_B control UA and UB. The default FET switch enable settings in this example are controlled by resistors RA and RB which pull the enable pin 1 of UA and UB to ground (low). In a real example, these enable signals are controlled by the Microchip IO expander. The default pull-down resistors connects the signals EXAMPLE_SIGNAL_A and EXAMPLE_SIGNAL_B and also connects signals EXAMPLE_SIGNAL_C and EXAMPLE_SIGNAL_D. To disconnect EXAMPLE_SIGNAL_A from EXAMPLE_SIGNAL_B, the Microchip IO expander is used to change ENABLE_A to a logic 1 through software that interfaces with the Microchip. The same procedure for ENABLE_B would disconnect EXAMPLE_SIGNAL_C from EXAMPLE_SIGNAL_D.
Figure 2-3 shows the equivalent circuit to Figure 2-2 but utilizes mechan-ical switches that are in the same package. Notice the default is shown by black boxes located closer to the ON label of the switches. In order to dis-connect these switches, physically move the switch to the OFF position.
Figure 2-2. Example of Individual FET Switches
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-5
ADSP-BF609 EZ-KIT Lite Hardware Reference
Figure 2-4 shows a bus switch example, reference designator UC (Pericom PI3LVD512ZHE), selecting between lettered functionality and numbered functionality. The signals on the left side are multiplexed signals with naming convention letter_number. The right side of the circuit shows the signals separated into letter and number, with the number on the lower group (eg. 0B1) and the letter on the upper group (eg. 0B2). The default setting is controlled by the signal CONTROL_LETTER_NUMBER which is pulled low. This selects the number signals on the right to be connected to the multiplexed signals on the left by default. In this example, the Microchip IO expander is not shown but controls the signal CONTROL_LETTER_NUMBER and allows the user to change the selection through software.
Figure 2-5 shows the equivalent circuit to Figure 2-4 but utilizes mechan-ical switches. Notice the default for reference designators SWC and SWD is illustrated by black boxes located closer to the ON label of the switches to enable the number signals by default. Also notice the default setting for reference designators SWE and SWF is OFF. In order to connect the letters instead of the numbers, the user physically changes all switches on SWC and SWD to the OFF position and all switches on SWE and SEF to the ON position.
Figure 2-3. Example of Mechanical Switch Equivalent to Figure 2-2
Software-Controlled Switches (SoftConfig)
2-6 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Figure 2-4. Example of Bus Switch
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-7
ADSP-BF609 EZ-KIT Lite Hardware Reference
SoftConfig on the ADSP-BF609 EZ-KIT LITEThe Microchip MCP23017 GPIO expander provides control for individ-ual and 10-bit electronic switches. The TWI0 interface of the processor communicates with the Microchip device. Two 10-bit switches, U40-41 are connected to the link port 1 and 0 interfaces, respectively. There are an additional 27 individual switches with default settings that enable basic board functionality.
Table 2-1 lists the ADSP-BF609 processor and EZ-KIT Lite interfaces that are available by default. Note that only interfaces affected by software switches are listed in Table 2-1.
Figure 2-5. Example of Mechanical Switch Equivalent to Figure 2-4
Software-Controlled Switches (SoftConfig)
2-8 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Programming SoftConfig SwitchesOn the ADSP-BF609 EZ-KIT Lite, three Microchip MCP23017 devices exist. Each of these devices have the following programming characteristics:
• Each switch has two programmable GPIO registers.
• Each GPIO register controls eight signals (software switches).
Table 2-1. Default ADSP-BF609 Processor Interface Availability
Interface Availability by Default
EMAC0 Fully connected, need SoftConfig to enable RMII clock
Rotary encoder Enabled
Link port 0 Enabled with selection of the boot mode 6 setting, or by configuring SoftConfig
CAN Enabled, the CAN0_ERR connection to the processor is disabled
UART TX, RX and RTS are enabled by default, use SoftConfig to enable other fea-tures listed in the UART0 section and Table 2-5
SMC (parallel flash) Enabled with selection of boot mode 1, can be changed with SoftConfig
SPI Flash Fully connected for quad mode by default
Temperature sensor Enabled, requires SoftConfig to connect interrupts
Push buttons Enabled (except for wake push button)
LEDs Enabled
GPIO Register Register Address
GPIOA 0x12
GPIOB 0x13
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-9
ADSP-BF609 EZ-KIT Lite Hardware Reference
• By default, the Microchip MCP23017 GPIO signals function as input signals.
The signals must be programmed as output signals to override their default values. The following table shows the Microchip register addresses and the values that must be written to them to program the signals as output signals.
Each of the examples in Cross Core Embedded Studio include source files that program the soft switches, even if the default settings are being used. The README for each example identifies only the signals that are being changed from their default values. The code that programs the soft switches is located in the SoftConfig_BF609.c file in each example.
The following tables (Table 2-2, Table 2-3, and Table 2-4) outline the default values for each of the three Microchip MCP23017 devices.
IODIR Register IODIR Register Address Value to be Written to Program Signals as Outputs
IODIRA 0x00 0
IODIRB 0x01 0
Table 2-2. I2C Hardware Address 0x21
GPIO MCP23017 Register Address Default Value
GPIOA 0x12 0x07
GPIOB 0x13 0xFC
Table 2-3. I2C Hardware Address 0x22
GPIO MCP23017 Register Address Default Value
GPIOA 0x12 0x0A
GPIOB 0x13 0x00
Software-Controlled Switches (SoftConfig)
2-10 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Page 12 of the “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1 shows how the three Microchip GPIO expanders are connected to the board’s ICs.
U41, a 10-bit bus switch, connects the link port 0 processor interface to J3 (link port connector) when the select input signal (pin 12) is high. By default, the U41 select input is controlled by the boot mode switch (SW2). When the boot mode switch is set to 1 (parallel flash boot), the select line is high, enabling the system memory controller (SMC) signals, connected through pins PA0-7 and PB0-1 of the processor. Setting the boot mode switch to 6 (link port boot) drives the select line low and enables the link port 0 connection to the J3 connector.
The U41 output selection, which is based on the boot mode selection, can be overridden by the Microchip (U46) signal GPA0. This override is useful in a case where the application needs to boot from parallel flash but then use the link port 0 afterwards. After setting the signal high (to disable U29), use GPA3 to control the output of U41.
The processor signals connected to U41 can be disconnected from the link port to support other features. The selection line must be low in order to disconnect the signals from the link port connector J3. This allows the signals to connect to the on-board parallel flash memory and EI3 connec-tors. See “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1 for details.
Table 2-4. I2C Hardware Address 0x23
GPIO MCP23017 Register Address Default Value
GPIOA 0x12 0x00
GPIOB 0x13 0x00
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-11
ADSP-BF609 EZ-KIT Lite Hardware Reference
U40, a 10-bit bus switch, controls the link port 1 connection to P8 (link port connector), EI3 (expansion interface), and SMC address signals. The default setting is high, which connects the SMC address bus to the parallel flash memory and connects the link port pins PA8-15 and PB2-3 to the expansion interface. The link port 1 can be selected by setting U46 signal GPA1 low.
Table 2-5 and Table 2-6 show the output signals of the Microchip GPIO expander (U45), with a TWI address of 0100 001X, where X represents the read or write bit. The signals that control an individual FET have an entry under the FET column. The Component Connected column shows the board IC that is connected if the FET is enabled. Note that some of the Microchip (U45) output signals are connected directly to components on the board. However, in most cases, the Microchip (U45) is controlling the enable signal of a FET switch. Also note that if a particular functionality of the processor signal is being used, it will be in bold font under the “Pro-cessor Signal” column.
Table 2-5. Output Signals of Microchip GPIO Expander (U45 Port A)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
0 CAN_EN Enable CAN IC, enabled by default
U55 High
1 ~CAN_STB CAN standby control input U55 High
2 ~CAN0_ERR_EN GPIO PE02 for CAN0 error U33 PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
U55 High
3 ~CAN0RX_EN CAN0RX connected to CAN IC U55
U34 PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
U55 Low
4 ~CNT0UD_EN Rotary counter 0 count up connected to rotary connec-tor
U30 PG11/SPT2_BD1/TM0_TMR6/CNT0_UD
SW9 Low
Software-Controlled Switches (SoftConfig)
2-12 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
5 ~CNT0DG_EN Rotary counter 0 count down connected to rotary connector
U31 PG12/SPT2_BD0/TM0_TMR7/CNT0_DG
SW9 Low
6 ~CNT0ZM_EN Rotary counter 0 count zero connected to rotary connec-tor
U32 PG07/SPT2_BFS/TM0_TMR5/CNT0_ZM
SW9 Low
7 RMII_CLK_EN RMII clock for EMAC0 dis-abled
U43 Low
Table 2-6. Output Signals of Microchip GPIO Expander (U45 Port B)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
0 ~UART0RTS_EN UART0 RTS connected to UART transceiver U39
U21 PD09/~SPI0_SEL5/UART0_RTS/SPI1_SEL4
U39 Low
1 ~UART0RX_EN UART0 RX connected to UART transceiver U39
U20 PD08/~UART0_RX~/TM0_ACI0
U39 Low
2 ~UART0CTS_EN UART0 CTS disconnected from UART transceiver U39 by default
U19 PD10/SPI0_RDY/~UART0_CTS/SPI1_SEL3
U39 High
3 ~UART0CTS_RTS_LPBK UART0 CTS and RTS not connected. Change to low for looping back UART0 CTS and RTS signals
U18 High
4 ~UART0CTS_RST_EN UART0 CTS signal not con-nected to input of reset IC (U48)
U17 High
Table 2-5. Output Signals of Microchip GPIO Expander (U45 Port A) (Cont’d)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-13
ADSP-BF609 EZ-KIT Lite Hardware Reference
Table 2-7 and Table 2-8 show the output signals of the Microchip GPIO expander (U46), with a TWI address of 0100 010X, where X represents the read or write bit. The signals that control an individual FET have an entry under the FET column. The Component Connected column shows the board IC that is connected if the FET is enabled. Note that some of the Microchip (U46) output signals are connected directly to components on the board. However, in most cases, the Microchip (U46) is controlling the enable signal of a FET switch. Also note that if a particular functionality of the processor signal is being used, it will be in bold font under the “Pro-cessor Signal” column.
5 ~UART0CTS_146_EN Allows pins 1, 4 and 6 of UART connector (J2) to be connected together and used as input to reset IC (U48). This is disabled by default.
U16 High
6 ~TEMP_IRQ_EN PG09 can be used as TEMP interrupt, disconnected by default
U9 PG09/SPT2_AD0/TM0_TMR4
U54 High
7 ~TEMP_THERM_EN PB15 can be used as TEMP thermal limit, disconnected by default
U10 PB15/ETH0_PTPPPS/PPI1_FS3
U54 High
Table 2-7. Output Signals of Microchip GPIO Expander (U46 Port A)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
0 OVERRIDE_SMC0_LP0_BOOT Overrides U41 select U29 Low
1 SMC0_EPPI2_LP1_SWITCH Controls U40 select line U28 High
Table 2-6. Output Signals of Microchip GPIO Expander (U45 Port B) (Cont’d)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
Software-Controlled Switches (SoftConfig)
2-14 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
3 SMC0_LP0_EN Controls U41 select if Override High
U28 High
4 ~LED1_GPIO_EN PG14 is used as GPIO output for LED1, enabled by default
U27 PG14/~UART1_RX~/~SYS_IDLE1~/TM0_ACI1
LED1 Low
5 ~LED2_GPIO_EN PG15 is used as GPIO output for LED2, enabled by default
U26 PG15/~UART1_TX/SYS_IDLE0~/SYS_SLEEP/TM0_ACI4
LED2 Low
6 ~LED3_GPIO_EN PE14 is used as GPIO output for LED3, enabled by default
U25 PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
LED3 Low
7 ~LED4_GPIO_EN PB11 is used as GPIO output for LED4, enabled by default
U24 PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
LED4 Low
Table 2-8. Output Signals of Microchip GPIO Expander (U46 Port B)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
0 ~PUSHBUTTON1_EN PB10 is used as GPIO input for push button 1, enabled by default
U23 PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
SW6 Low
1 ~PUSHBUTTON2_EN PE01 is used as GPIO input for push button 2, enabled by default
U22 PE01/SPI1_D2/PPI0_D19/SPT1_BD0
SW7 Low
2 ~SD_CD_EN SD memory card detect connected to GPIO PG10, enabled by default
U15 PG10/~UART1_RTS~/SPT2_BCLK
J5 Low
Table 2-7. Output Signals of Microchip GPIO Expander (U46 Port A) (Cont’d)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-15
ADSP-BF609 EZ-KIT Lite Hardware Reference
Table 2-9 and Table 2-10 show the output signals of the Microchip GPIO expander (U47), with a TWI address of 0100 011X, where X represents the read or write bit. The signals that control an individual FET have an entry under the FET column. The Component Connected column shows the board IC that is connected if the FET is enabled.Note that some of the Microchip (U47) output signals are connected directly to components on the board. However, in most cases, the Microchip (U47) is controlling the enable signal of a FET switch. Also note that if a particular functionality of the processor signal is being used, it will be in bold font under the “Pro-cessor Signal” column.
3 ~SD_WP_EN SD memory write pro-tect connected to GPIO PG10, enabled by default
U14 PG13/~UART1_CTS~/TM0_CLK
J5 Low
4 ~SPIFLASH_CS_EN SPI flash chip select SPI0SEL1 connection to U38 SPI flash, connected by default
U13 PD11/~SPI0_SEL1/SPI0_SS
U38 Low
5 ~SPI0D2_EN SPI flash data 2 connec-tion to U38 SPI flash, connected by default. This is needed for quad access mode.
U12 PD00/SPI0_D2/PPI1_D16/~SPI0_SEL3
U38 Low
6 ~SPI0D3_EN SPI flash data 3 connec-tion to U38 SPI flash, connected by default. This is needed for quad access mode.
U16 PD01/SPI0_D3/PPI1_D17/~SPI0_SEL2
U38 Low
Table 2-8. Output Signals of Microchip GPIO Expander (U46 Port B) (Cont’d)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
Software-Controlled Switches (SoftConfig)
2-16 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Table 2-9. Output Signals of Microchip GPIO Expander (U47 Port A)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
0 PHYINT_EN1 Connects Ethernet 0 interrupt signal to Ethernet PHY, con-nected by default
U35 PD06/~ETH0_PHYINT~/PPI1_FS2/TM0_ACI5
U49 Low
1 PHY_PWR_DWN_INT2 Controls power down of the Ethernet PHY if PHYINT_EN high
U49 High-Z
2 PHYAD03 Allows the PHY to be placed in isolate mode
U49 High-Z
3 ~ETHERNET_EN Disconnects EMAC0 signals from U49
U4/U5 Low
4 ~WAKE_PUSHBUTTON_EN Enables push button input to processor
U7 PE12/~ETH1_PHYINT~/PWM1_CL/RSI0_D5
U1 High
5 ~PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3_EN
Connects processor sig-nal to EI3 connectors, disabled by default
U36 PD00/SPI0_D2/PPI1_D16/~SPI0_SEL3
EI3 High
6 ~PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3_EN
Connects processor sig-nal to EI3 connectors, disabled by default
U51 PD01/SPI0_D3/PPI1_D17/~SPI0_SEL2
EI3 High
7 ~PD2_SPI0MISO_EI3_EN
Connects processor sig-nal to EI3 connectors, disabled by default
U57 PD02/SPI0_MISO EI3 High
1 This is an active low signal but the signal name does not show this. 2 This signal defaults to an input setting, putting the signal in High-Z. Must be used in concert with
PHYINT_EN. Set PHYINT_EN high first and then control PHY_PWR_DWN_INT. 3 This signal defaults to an input setting, putting the signal in High-Z. There is a 2.21k resistor pull-up,
which sets the PHY address appropriately. If isolate mode is desired, the signal needs to be set as an out-put and driven appropriately.
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-17
ADSP-BF609 EZ-KIT Lite Hardware Reference
Push Buttons and SwitchesThis section describes operation of the push buttons and switches. The push button and switch locations are shown in Figure 2-6.
Table 2-10. Output Signals of Microchip GPIO Expander (U47 Port B)
Bit Signal Name Description FET Processor Signal (if applicable)
Component Connected
Default
0 ~PD3_SPI0MOSI_EI3_EN Connects processor sig-nal to EI3 connectors, disabled by default
U56 PD03/SPI0_MOSI EI3 High
1 ~PD4_SPI0CK_EI3_EN Connects processor sig-nal to EI3 connectors, disabled by default
U58 PD04/SPI0_CLK EI3 High
Figure 2-6. Push Button and Switch Locations
Push Buttons and Switches
2-18 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
JTAG Interface Switches (SW1, SW3–5)The JTAG switches (SW1, SW3, SW4, and SW5) select between a single-pro-cessor (one board) and multi-processor (more than one board) configurations. By default, the four DIP switches are set up for a single EZ-KIT Lite configuration. See Table 2-11.
The default configuration applies to either a debug agent or an external emulator, such as the Analog Devices high-performance USB-based emu-lator (HP-USB) or ICE-100B emulator.
To use an external emulator and multiple EZ-KIT Lites simultaneously in one CrossCore Embedded Studio (CCES) multi-processor session, set up the boards as shown in Table 2-12. Attach the boards to each other via connectors J3 and P8. For two EZ-KIT Lites, no external cables are required. For three or more EZ-KIT Lites, obtain Samtec JTAG cables described in “Link Port /JTAG Connectors (J3 and P8)” on page 2-25.
Table 2-11. Single-Processor Configuration
Switch Position Single EZ-KIT Lite Use (Default)
SW1.1 ON
SW1.2 OFF
SW1.3 ON
SW1.4 OFF
SW1.5 ON
SW1.6 OFF
SW1.7 ON
SW1.8 OFF
SW3.1 ON
SW3.2 OFF
SW4.1 ON
SW4.2 OFF
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-19
ADSP-BF609 EZ-KIT Lite Hardware Reference
Boot Mode Select Switch (SW2)The rotary boot mode select switch (SW2) determines the boot mode of the processor. Table 2-13 shows the available boot mode settings. By default, the ADSP-BF609 processor boots from 8-bit flash memory (parallel flash boot).
SW5.1 OFF
SW5.2 OFF
Table 2-12. Multiple-Processor Configuration
Switch Position Main EZ-KIT LiteAttached to Emulator
EZ-KIT LiteNot Attached to Emulator
SW1.1 ON OFF
SW1.2 ON ON
SW1.3 ON OFF
SW1.4 ON ON
SW1.5 ON OFF
SW1.6 ON ON
SW1.7 ON OFF
SW1.8 ON ON
SW3.1 ON OFF
SW3.2 OFF OFF
SW4.1 OFF OFF
SW4.2 ON ON
SW5.1 OFF ON
SW5.2 ON OFF
Table 2-11. Single-Processor Configuration (Cont’d)
Switch Position Single EZ-KIT Lite Use (Default)
Push Buttons and Switches
2-20 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
IRQ/Flag Enable Switches (SW6–7)The IRQ/flag enable switches (SW6–7) are push buttons which provide a momentary low signal on processor signals PB10_A24_SP1D1 and PE1_SPI1D2_EPPI0D19_SP3D0 when enabled through the software-controlled switch.
Reset Switch (SW8)The reset switch (SW8) is a push button which provides a reset pulse to the ADSP-BF609 processor (U1), Ethernet PHY (U49), GPIO extenders (U45-47), and the expansion interface (EI3) connectors.
Rotary Encoder With Momentary Switch (SW9)The rotary encoder (SW9) can be turned clockwise for an up count or counter-clockwise for a down count. The encoder also features a momen-tary switch, activated by pushing the switch towards the center of the board, that can be used to set the counter to zero. The rotary encoder is a two-bit quadrature (Gray code) encoder.
Table 2-13. Boot Mode Select Switch (SW2)
SW2 Position Processor Boot Mode
0 Idle—no boot
1 Parallel flash boot (default)
2 RSI master boot
3 SPI0 master boot
4 SPI0 slave boot
5 Reserved
6 Link port 0 slave boot
7 UART0 slave boot
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-21
ADSP-BF609 EZ-KIT Lite Hardware Reference
The rotary encoder can be disconnected from the processor by setting SoftConfig, see “Software-Controlled Switches (SoftConfig)” on page 2-3 for more information.
Wake Push Switch (SW10)One of the wake input signals (PE12/~ETH1_PHYINT/PWM1_CL/RSI0_D5) is connected to a push button switch (SW10). This feature is disabled by default and can be enabled through SoftConfig. Refer to “Software-Con-trolled Switches (SoftConfig)” on page 2-3 for more details.
Power JumpersThis section describes functionality of the power jumpers (P10-15). Figure 2-7 shows the jumper locations.
Figure 2-7. Configuration Jumper Locations
LEDs
2-22 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Remove jumpers listed in Table 2-14 to measure the respective voltage domain.
LEDsThis section describes the on-board LEDs. Figure 2-7 shows the LED locations.
Table 2-14. Power Jumpers (P10-15)
Jumper Power Domain
P15 VDD_DMC
P14 VDD_INT
P13 3.3V
P12 VDD_EXT
P11 VDD_USB
P10 USB_VBUS
Figure 2-8. LED Locations
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-23
ADSP-BF609 EZ-KIT Lite Hardware Reference
GPIO LEDs (LED1–4)Four LEDs (LED1, LED2, LED3, and LED4) are connected to four gen-eral-purpose I/O pins of the processor (see Table 2-15). The LEDs are active high and lit (amber) by writing a “1” to the corresponding program-mable flag signal.
Thermal Limit LED (LED5)The thermal limit LED (LED5) reports the status of the thermal sensor, ADM1032 (U54). The thermal sensor monitors the processor’s tempera-ture. When the high temperature limit set by the IC is violated, LED5 is turned on (amber) as a visual indicator. The ADM1032 device has built-in hysteresis, which causes the LED to de-activate only when the temperature is significantly within the limit. For more information, see “Temperature Sensor Interface” on page 1-17.
Power LED (LED6)When LED6 is lit solid (green), it indicates that power is being supplied to the board properly.
Table 2-15. GPIO LEDs
LED Reference Designator Processor Programmable Flag Pin
LED1 PG14
LED2 PG15
LED3 PE14
LED4 PB11
Connectors
2-24 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Reset LED (LED7)When LED4 is lit (red), it indicates that the master reset of the processor is active. The reset signal is controlled by the Analog Devices ADM13305 supervisory reset circuit.
SPD LED (LED6)SPD LED indicates the speed of the Ethernet port. When LED6 is lit (green), the speed is 100 Mb/s and when not lit, the speed is 10 Mb/s.
ConnectorsThis section describes connector functionality and provides information about mating connectors. The connector locations are shown in Figure 2-9.
Figure 2-9. Connector Locations
Components with a dotted outline are on the back side of the board
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-25
ADSP-BF609 EZ-KIT Lite Hardware Reference
DCE UART Connector (J2)The pinout of the J2 connector can be found in “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1.
Link Port /JTAG Connectors (J3 and P8)The J3 and P8 connectors provide access to the Link Port and JTAG sig-nals of the ADSP-BF609 processor. J3 supports link port 0 and the P8 connector is for link port 1.
JTAG Connector (P1)The JTAG interface of the ADSP-BF609 processor is connected to the 14-pin 0.1” header, P1. Pin 3 is missing to provide keying. Pin 3 in the mating connector must have a plug. For more information, see “JTAG Interface” on page 1-18.
Remove the standalone debug agent when an emulator is used with the board. Follow the installation instructions provided in “EZ-KIT Lite Installation” on page 1-6, using P1 as the JTAG connection point.
Part Description Manufacturer Part Number
IDC header FCI 68737-410HLF
Mating Connector
IDC socket DIGI-KEY S4205-ND
Part Description Manufacturer Part Number
ERF8 10X2, RA female (J3) SAMTEC ERF8-010-01-S-D-RA-L
ERm8 10x2, RA male (P8) SAMTEC ERM8-010-01-S-D-RA-TR
Mating Cable
6" cable ERF8 to ERM8 10X2 SAMTEC ERCD-010-06.00-TBL-SBR-1
Connectors
2-26 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
JTAG Connector (ZP1)ZP1 is the connecting point for the SADA2 debug interface and is a 14-pin 0.1” header.
Expansion Interface III Connectors (P1A–C, P2A, P3A)
Five board-to-board connectors (P1A, P1B, P1C, P2A, and P3A) provide sig-nals from the SPI, TWI, UART, SPORT, and GPIO interfaces of the processor. The connectors are located on the bottom side of the board. For more information, see “Expansion Interface III” on page 1-20.
USB Connector (P7)
Power Connector (P18)
Part Description Manufacturer Part Number
120-pin, 0.6 mm HIROSE FX8-120P-SV1(91)
Mating Connector
120-pin, 0.6 mm HIROSE FX8-120S-SV(21)
Part Description Manufacturer Part Number
USB mini-Ab MOLEX 56579-0576
Part Description Manufacturer Part Number
0.65 mm power jack CUI 045-0883R
Mating Connector
[email protected] power supply GLOBETEK GS-1750(R)
ADSP-BF609 EZ-KIT Lite Evaluation System Manual 2-27
ADSP-BF609 EZ-KIT Lite Hardware Reference
CAN Connector (J4)
SD Connector (J5)
Ethernet Connector (J1)
Ethernet Connectors (P16-17)P16 and P17 allow connection to the Ethernet port IEEE 1588 signals. They are 6-pin 0.1” headers. The pinout of the P16 and P17 connectors can be found in “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1.
Part Description Manufacturer Part Number
RJ-11 4-pin modular jack TYCO 5558872-1
Mating Cable
4-conductor modular jack cable L-COM TSP3044
Part Description Manufacturer Part Number
SD 8-bit, 2 GB SANDISK MHC-W21-601
Memory Card
2 GB SANDISK SDSDB-2048-A11
Part Description Manufacturer Part Number
RJ-45 Ethernet jack Pulse Engineer PN J0011D21BNL
Mating Cable
Standard Ethernet cable
Connectors
2-28 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
ADSP-BF609 EZ-KIT Lite Evaluation System Manual A-1
A ADSP-BF609 EZ-KIT LITE BILL OF MATERIALS
The bill of materials corresponds to “ADSP-BF609 EZ-KIT Lite Schematic” on page B-1.
Ref. Qty. Description Reference Designator
Manufacturer Part Number
1 1 ADM708SARZ SOIC8
U48 ADI ADM708SARZ
2 1 ADM3315 TSSOP24
U39 ADI ADM3315EARUZ
3 1 ADSP-BF609 BGA349C80P22X22_1900X1900
U1 ADI ADSP-BF609-ENG
4 1 ADP1864AUJZ SOT23-6
VR1 ADI ADP1864AUJZ-R7
5 1 ADP1715 MSOP8 VR3 ADI ADP1715ARMZ-1.8-R7
6 1 74LVC14A SOIC14 U3 TI 74LVC14AD
7 1 IDT74FCT3244APY SSOP20
U8 IDT IDT74FCT3244APYG
8 2 SN74LVC1G08 SOT23-5
U52-U53 TI SN74LVC1G08DBVR
9 1 TJA1041 SOIC14 U55 NXP TJA1041T/VM,512
10 1 SN74LVC1G04 SOT23-5
U59 TI SN74LVC1G04DBVT
11 2 SN74CB3Q3245 TSSOP20
U4-U5 DIGI-KEY 296-19130-1-ND
12 1 MIC2025-1 SOIC8 U50 DIGI-KEY 576-1057-ND
A-2 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
13 1 MT47H64M16 FBGA84
U37 MICRON MT47H64M16HR-3 L
14 1 ADM1032 SOIC_N8
U54 ON SEMI ADM1032ARZ
15 1 DP83848 LQFP48 U49 NATIONAL SEMI
DP83848CVV/NOPB
16 1 50MHZ OSC012 U43 DIGI-KEY 300-8264-2-ND
17 33 PI3A125 SC70_5 U7,U9-U36,U51, U56-U58
PERICOM PI3A125CEX
18 3 MCP23017 QFN65P600X600-29N
U45-U47 DIGI-KEY MCP23017-E/ML-ND
19 2 PI3LVD512 QFN50P350X900-43N
U40-U41 PERICOM PI3LVD512ZHE
20 1 BF609 PC28F128P33B U44
U44 MICRON PC28F128P33BF60D
21 1 BF609 W25Q32 U38
U38 WINBOND W25Q32BVSSIG
22 1 SI7403BDN ICS010 U6 VISHAY SI7403BDN
23 1 25MHZ OSC003 U42 DIGI-KEY SG-8002CA-SCB-ND
24 1 48MHZ OSC003 U2 DIGI-KEY SG-8002CA-SCB-ND(48.00M)
25 1 ADP2119ACPZ-R7 DFN50P300X300-11N
VR2 ANA00 ADP2119ACPZ-R7
26 1 DIP8 SWT016 SW1 C&K TDA08H0SB1
27 2 IDC 3X2 IDC3X2_SMT
P16-P17 SAMTEC TSM-103-01-T-DV
28 1 DB9 9PIN CON038 J2 NORCOMP 191-009-213-L-571
Ref. Qty. Description Reference Designator
Manufacturer Part Number
ADSP-BF609 EZ-KIT Lite Evaluation System Manual A-3
ADSP-BF609 EZ-KIT Lite Bill Of Materials
29 1 RJ11 4PIN CON039
J4 TYCO 5558872-1
30 3 DIP2 SWT020 SW3-SW5 C&K CKN9064-ND
31 6 IDC 2X1 IDC2X1 P10-P15 FCI 90726-402HLF
32 1 3A RESETABLE FUS004
F1 TYCO SMD300F-2
33 6 IDC 2PIN_JUMPER_SHORT
SJ1-SJ6 DIGI-KEY S9001-ND
34 1 PWR .65MM CON045
P18 DIG CP1-023-ND
35 1 USB_MINI-AB 5PIN CON052
P7 MOLEX 56579-0576
36 4 MOMENTARY SWT024
SW6-SW8,SW10 PANA-SONIC
EVQ-Q2K03W
37 1 ROTARY_ENC_EDGE SWT025
SW9 PANA-SONIC
EVQ-WKA001
38 2 IDC 7x2 IDC7x2_SMTA
P1,ZP1 SAMTEC TSM-107-01-T-DV-A
39 1 ROTARY SWT027 SW2 COPAL S-8110
40 1 ERM8 10X2 ERM8_10X2_SMT
P8 SAMTEC ERM8-010-01-S-D-RA-TR
41 1 ERF8 10X2 ERF8_10X2_SMT
J3 SAMTEC ERF8-010-01-S-D-RA-L-TR
42 1 RJ45 W/LEDS CON065
J1 PULSE ENG.
J0011D21BNL
43 1 SD_CONN 8-BIT CON067
J5 MORETHA-NALL
MHC-W21-601-LF
44 5 .6MM 120PIN HIROSE_FX8-120P-SV1(91)
P1A,P1B,P1C,P2A,P3A
HIROSE FX8-120P-SV1(91)
Ref. Qty. Description Reference Designator
Manufacturer Part Number
A-4 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
45 1 TEST LOOP LOOP_2838
GP1 KEYSTONE 5016
46 5 YELLOW LED001 LED1-LED5 DIGI-KEY P512TR-ND
47 3 600 100MHZ 500MA 1206
FER1-FER3 STEWARD HZ1206B601R-10
48 2 1UF 16V 10% 0805 C87-C88 DIGI-KEY 399-1284-2-ND
49 2 0 1/8W 5% 0805 R200,R211 VISHAY CRCW08050000Z0EA
50 1 190 100MHZ 5A FER002
FER4 MURATA DLW5BSN191SQ2
51 7 10UF 6.3V 10% 0805
C39,C117-C118, C163-C164, C177-C178
AVX 08056D106KAT2A
52 1 4.7UF 6.3V 10% 0805
C90 AVX 08056D475KAT2A
53 40 0.1UF 10V 10% 0402
C17-C18, C41-C45,C84, C95,C100, C115-C116, C135-C142, C153-C162, C173-C176,C186,C188-C191,C200
AVX 0402ZD104KAT2A
54 124 0.01UF 16V 10% 0402
C1-C15,C19, C22-C24, C26-C38,C40, C46-C61, C64-C83,C94, C96-C98, C104-C107, C111-C113, C119-C134, C143-C152, C165-C172, C179-C185,C192,C198-C199
AVX 0402YC103KAT2A
Ref. Qty. Description Reference Designator
Manufacturer Part Number
ADSP-BF609 EZ-KIT Lite Evaluation System Manual A-5
ADSP-BF609 EZ-KIT Lite Bill Of Materials
55 102 10K 1/16W 5% 0402
R9-R12,R17-R18,R20-R33,R39-R48,R50-R52,R56-R63,R65-R67,R69-R72,R80-R84,R89-R96,R100-R101,R104-R105,R107-R111,R113,R118-R119,R133-R135,R142,R146,R148-R149,R158-R160,R167,R169-R170,R174,R188,R205-R206,R210,R218-R221,R230-R235,R239
VISHAY CRCW040210K0FKED
56 1 4.7K 1/16W 5% 0402
R64 VISHAY CRCW04024K70JNED
57 13 0 1/16W 5% 0402 R5-R6,R53,R120,R136,R161-R162,R165,R168,R228-R229,R238,R240
PANA-SONIC
ERJ-2GE0R00X
58 17 33 1/16W 5% 0402 R8,R13,R34,R37-R38,R54-R55,R85-R86,R137-R138, R140,R172-R173,R227,R244-R245
VISHAY CRCW040233R0JNEA
59 1 1.5UH 20% IND003
L2 COIL CRAFT
DO1608C-152MLC
60 1 150UF 10V 10% D CT1 DIGI-KEY 478-3321-2-ND
61 2 2.2UF 10V 10% 0805
C99,C101 AVX 0805ZD225KAT2A
62 1 1A SK12 DO-214AA
D8 DIODES INC
B120B-13-F
63 2 107.0 1/10W 1% 0805
R190,R192 DIGI-KEY 311-107CRTR-ND
Ref. Qty. Description Reference Designator
Manufacturer Part Number
A-6 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
64 1 4.7UF 25V 20% 0805
C25 AVX 0805ZD475KAT2A
65 1 68PF 50V 5% 0603 C91 AVX 06035A680JAT2A
66 1 470PF 50V 5% 0603 C92 AVX 06033A471JAT2A
67 1 220UF 6.3V 20% D2E
CT3 SANYO 10TPE220ML
68 1 1M 1/10W 5% 0603 R19 VISHAY CRCW06031M00FNEA
69 5 0.0 1/10W 1% 0603 R129,R214-R217 PHYCOMP 232270296001L
70 3 10 1/10W 5% 0603 R151-R152,R237 VISHAY CRCW060310R0JNEA
71 1 4700PF 16V 10% 0603
C110 DIGI-KEY 311-1083-2-ND
72 2 100PF 50V 5% 0603 C108-C109 AVX 06035A101JAT2A
73 10 2.21K 1/10W 1% 0603
R186-R187,R191,R199,R201-R204,R207-R208
DIGI-KEY 311-2.21KHRTR-ND
74 2 62.0 1/10W 1% 0603
R153-R154 DIGI-KEY 311-62.0HRTR-ND
75 3 1UF 6.3V 20% 0402 C62-C63,C93 PANA-SONIC
ECJ-0EB0J105M
76 3 100 1/16W 5% 0402
R87-R88,R141 DIGI-KEY 311-100JRTR-ND
77 1 24.9K 1/10W 1% 0603
R132 DIGI-KEY 311-24.9KHTR-ND
78 3 10UF 10V 10% 0805
C16,C114,C187 PANA-SONIC
ECJ-2FB1A106K
79 6 0.05 1/2W 1% 1206 R121,R124-R126,R144-R145
SEI CSF 1/2 0.05 1%R
80 2 10UF 16V 10% 1210
C86,C103 AVX 1210YD106KAT2A
Ref. Qty. Description Reference Designator
Manufacturer Part Number
ADSP-BF609 EZ-KIT Lite Evaluation System Manual A-7
ADSP-BF609 EZ-KIT Lite Bill Of Materials
81 2 GREEN LED001 LED6,LED8 PANA-SONIC
LN1361CTR
82 1 RED LED001 LED7 PANA-SONIC
LN1261CTR
83 2 1000PF 50V 5% 1206
C85,C89 AVX 12065A102JAT2A
84 1 255.0K 1/10W 1% 0603
R130 VISHAY CRCW06032553FK
85 1 80.6K 1/10W 1% 0603
R131 VISHAY CRCW060380K6FKEA
86 3 5A MBRS540T3G SMC
D5-D7 ON SEMI MBRS540T3G
87 1 VARISTOR V5.5MLA 30A 0603
R1 LITTLE-FUSE
V5.5MLA0603
88 1 THERM 0.5A 0.4 1206
R209 LITTLE-FUSE
1206L050-C
89 1 2.5UH 30% IND013
L1 COIL-CRAFT
MSS1038-252NL_
90 7 330.0 1/16W 1% 0402
R73-R79 DIGI-KEY 541-330LCT-ND
91 5 1.0K 1/16W 1% 0402
R2-R3,R155-R157 PANA-SONIC
ERJ-2RKF1001X
92 3 1.50K 1/16W 1% 0402
R15-R16,R175 PANA-SONIC
ERJ-2RKF1501X
93 13 0 1/16W 5% RNS005
RN1-RN13 PANA-SONIC
EXB-28VR000X
94 3 22UF 16V 10% 1210
C201-C203 YAIYO YUDEN
EMK325BJ226KM-T
95 1 33 1/16W 5% RNS003
RN14 PANA-SONIC
EXB-2HV330JV
Ref. Qty. Description Reference Designator
Manufacturer Part Number
A-8 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
96 1 100.0 1/16W 1% 0402
R4 DIGI-KEY 541-100LCT-ND
97 2 0.036 1/2W 1% 1206
R127-R128 SUSUMU RL1632S-R036-F
98 1 30A GSOT05 SOT23-3
D2 VISHAY GSOT05-GS08
99 2 30A GSOT03 SOT23-3
D3-D4 VISHAY GSOT03-GS08
100 1 40A ESD5Z2.5T1 SOD-523
D1 ON SEMI ESD5Z2.5T1G
101 2 165.0 1/10W 1% 0603
R197-R198 DIGI-KEY P165HTR-ND
102 1 220.0 1/10W 1% 0603
R185 DIGI-KEY P220HTR-ND
103 1 4.87K 1/10W 1% 0402
R189 DIGI-KEY 541-4.87KHCT-ND
104 13 49.9 1/16W 1% 0402
R176-R184,R193-R196
STACK-POLE
RMCF0402FT49R9
105 1 15KV ESD7004 DFN50P250X100-10N
D10 ON SEMI ESD7004MUTAG
106 1 15KV ESDA6V1SC SOT95P280-6N
D9 DIGI-KEY 497-6637-1-ND
107 1 30K 1/10W 1% 0402
R242 PANA-SONIC
ERJ-2RKF3002X
108 1 32.4K 1/10W 1% 0402
R243 PANA-SONIC
ERJ-2RKF3242X
Ref. Qty. Description Reference Designator
Manufacturer Part Number
ADSP-BF609 EZ-KIT Lite Evaluation System Manual I-1
I INDEX
AADSP-BF609 Blackfin processor, xiiADSP-BF609 processor memory map, 1-11architecture, of this EZ-KIT Lite, 2-2
Bbill of materials, A-1board schematic (ADSP-BF609), B-1boot
modes, 2-19mode select switch (SW2), 2-19
bus switch, 2-5example, 2-6
CCAN connector (J4), 2-27CAN interface, 1-14configuration, of this EZ-KIT Lite, 1-3connectors, 2-24
diagram of locations, 2-24J1 (ethernet), 2-27J2 (DCE UART), 2-25J3 and P8 (Link Port / JTAG), 2-25J4 (CAN), 2-27J5 (SD), 2-27P16-17 (ethernet), 2-27P18 (power), 2-26P1A-C (expansion), 2-26P1 (JTAG), 2-25
P2A (expansion), 2-26P3A (expansion), 2-26P7 (USB), 2-26ZP1 (JTAG), 2-26
contents, of this EZ-KIT Lite package, 1-2customer support, xvii
DDCE UART connector (J2), 2-25DDR2 SDRAM controller, 1-12default configuration, of this EZ-KIT Lite, 1-3default jumper and switch settings, 1-4default processor interface availability, 2-7design reference info, 1-22
EEngineerZone, xviiiethernet
connector (J1), 2-27connectors (P16-17), 2-27
ethernet interface, 1-13example programs, 1-22expansion interface, 1-20, 2-26
FFET switches, 2-4
example, 2-4
Index
I-2 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Ggeneral-purpose I/O (GPIO), 1-18general-purpose I/O pins (GPIO), 2-23
Iinstallation, of this EZ-KIT Lite, 1-4, 1-6IRQ / Flag enable switches (SW6-7), 2-20
JJTAG connector (P1), 2-25JTAG connector (ZP1), 2-26JTAG interface, 1-18JTAG interface switches (SW1, SW3-5), 2-18jumpers
diagram of locations, 2-21
LLEDs, 2-22
diagram of locations, 2-22LED1-4 (GPIO), 2-23LED5 (thermal limit), 2-23LED6 (power), 2-23LED6 (SPD), 2-24LED7 (reset), 2-24
license restrictions, xii, 1-10Link Port / JTAG connectors (J3 and P8), 2-25link ports interface, 1-17
Mmechanical switch, 2-5, 2-7memory map, of this EZ-KIT Lite, 1-10Micro Signal Architecture (MSA), xi
Nnotation conventions, xx
Ooperating systems, supported, 1-5
Ppackage contents, 1-2power
architecture, 1-21LED (LED6), 2-23measurements, 1-21
power connector (P18), 2-26power jumpers, 2-21power-on-self test (POST), 1-20product overview, xiiprogramming SoftConfig switches, 2-8push buttons and switches, 2-17
RReduced Instruction Set Computing (RISC), xirelated documents, xixreset
LEDs (LED7), 2-24reset switch (SW8), 2-20restriction, of the evaluation license, 1-10rotary encoder interface, 1-16rotary encoder switch (SW9), 2-20
Sschematic, of ADSP-BF609 EZ-KIT Lite, B-1SD connector (J5), 2-27SD interface, 1-16SMC interface, 1-13SoftConfig
on the EZ-KIT Lite, 2-7, 2-11overview, 2-3programming switches, 2-8
SPDLEDs (LED6), 2-24
SPI interface, 1-13
ADSP-BF609 EZ-KIT Lite Evaluation System Manual I-3
SRAM memory, 1-12See also memory map
startup, of this EZ-KIT Lite, 1-7supported operating systems, 1-5SW1, SW3-5 (JTAG) interface switches, 2-18SW10 (wake push) switch, 2-21SW2 (boot mode select) switch, 2-19SW6-7 (IRQ / Flag enable) switches, 2-20SW8 (reset) switch, 2-20SW9 (rotary encoder) switch, 2-20switches
programming SoftConfig, 2-8SW1, SW3-5 (JTAG interface), 2-18SW10 (wake push), 2-21SW2 (boot mode select), 2-19SW6-7 (IRQ / Flag enable), 2-20SW8 (reset), 2-20SW (rotary encoder), 2-20
switches, diagram of locations, 2-17system architecture, of this EZ-KIT Lite, 2-2system requirements, 1-5
Ttemperature sensor interface, 1-17thermal limit
LED (LED5), 2-23
UUART interface, 1-15USB connector (P7), 2-26USB OTG HS interface, 1-14
Wwake push switch (SW10), 2-21
Index
I-4 ADSP-BF609 EZ-KIT Lite Evaluation System Manual
Title Block
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.01
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
ADSP-BF609 EZ-BoardSCHEMATIC
DSP DDR2 Interface
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.02
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
R600402
0402
R31.0K
C20.01UF0402
C90.01UF0402
C30.01UF0402
C180.1UF0402
R21.0K0402
R4100.00402
C40.01UF0402
C50.01UF0402
C60.01UF0402
C70.01UF0402
C80.01UF0402
C100.01UF0402
C110.01UF0402
C120.01UF0402
C130.01UF0402
C140.01UF0402
C150.01UF0402
C170.1UF0402
C1610UF0805
RN8
0RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
0
RN3
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
0
RN13
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
RN10
0RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
RN11
0RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
RN6
0RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
RN7
0RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
0
RN2
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
C10.01UF0402
C84
04020.1UF
0
RN12
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
0
RN5
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
0
RN4
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
U37
MT47H64M16FBGA84
K3
A8
K7
E8
L8
K8L7
J2
G7
G3
G1
E9
C9
C7
C3
C1
G9
A9
J1R1
M9
J9E1
A1
B7
B3
R7
R3
R8
K9 E2
A2
F7
F3
H2
F8
F2
E7
D8
D2
B8
B2
H8
A7 J7P9
N1J3E3
A3
C2
C8
F9
F1
H9
H1
H3
H7
B9
B1
D9
D1
D3
D7
G2
G8
K2
J8
L1
L3
L2
P3
P8
P2
N7
N3
N8
N2
M7
R2
P7
M2
M3
M8A0
A1
A10/AP
A11
A12
A2
A3
A4
A5
A6
A7
A8
A9
BA0
BA1
BA2
CK
CKE
DQ0
DQ1
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
GN
D1
GN
D2
GN
D3
GN
D4
GN
D5
GN
DL
GN
DQ
1
GN
DQ
10
GN
DQ
2G
ND
Q3
GN
DQ
4G
ND
Q5
GN
DQ
6G
ND
Q7
GN
DQ
8G
ND
Q9
LDM
LDQS
NC1
NC2ODT
RFU/A13
RFU/A14
RFU/A15
UDM
UDQS
VD
D1
VD
D2
VD
D3
VD
D4
VD
D5
VD
DL
VD
DQ
1
VD
DQ
10
VD
DQ
2V
DD
Q3
VD
DQ
4V
DD
Q5
VD
DQ
6V
DD
Q7
VD
DQ
8V
DD
Q9
VREF
CAS CK
CS
LDQS
RAS
UDQS
WE
R500402
U1
ADSP-BF609BGA349C80P22X22_1900X1900
L19
R20
V20
R21
J20
H20
N20
P20
E20
F20
L20
M20
K20
G20
G22
G21
K21
K22
F22
H21
E21
J22
J21
E22
H22
F21
M21
M22
P21
N22
N21
P22
L21
L22
Y21
U22
Y22
T20
W20
U21
W21
T21
W22
U20
R22
V22
T22
V21DMC0_A13
DMC0_A12
DMC0_A11
DMC0_A10
DMC0_A09
DMC0_A08
DMC0_A07
DMC0_A06
DMC0_A05
DMC0_A04
DMC0_A03
DMC0_A02
DMC0_A01
DMC0_A00
DMC0_DQ07
DMC0_DQ06
DMC0_DQ05
DMC0_DQ04
DMC0_DQ03
DMC0_DQ02
DMC0_DQ01
DMC0_DQ00
DMC0_DQ15
DMC0_DQ14
DMC0_DQ13
DMC0_DQ12
DMC0_DQ11
DMC0_DQ10
DMC0_DQ09
DMC0_DQ08
DMC0_LDQS
DMC0_LDQS
DMC0_UDQS
DMC0_UDQS
DMC0_UDM
DMC0_LDM
DMC0_CK
DMC0_CK
DMC0_CS0
DMC0_CAS
DMC0_CKE
DMC0_WE
DMC0_RAS
DMC0_ODT
DMC0_BA0
DMC0_BA1
DMC0_BA2
VREF_DMC
0
RN1
RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
RN9
0RNS005
3
4
2
1 8
7
6
5R4B
R3B
R2B
R1BR1A
R2A
R4A
R3A
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
DMC0_DQ04_Z
DMC0_DQ04_Z
DMC0_ODT
DMC0_ODT
DMC0_CS0
DMC0_CS0
DMC0_UDM
DMC0_UDM
DMC0_LDM
DMC0_LDMDMC0_CK
DMC0_CK
DMC0_RAS
DMC0_RAS
DMC0_CK
DMC0_CK
DMC0_CAS
DMC0_CAS
DMC0_WE
DMC0_WE
DMC0_CKE
DMC0_CKE
DMC0_A13
DMC0_A13
DMC0_A10
DMC0_A10
DMC0_A09
DMC0_A09
DMC0_A08
DMC0_A08
DMC0_A07
DMC0_A07
DMC0_A05
DMC0_A05
DMC0_A03
DMC0_A03
DMC0_A02
DMC0_A02
DMC0_A01
DMC0_A01
DMC0_A00
DMC0_A00
DMC0_BA0
DMC0_BA0
DMC0_DQ05
DMC0_DQ05
DMC0_DQ04
DMC0_DQ04
DMC0_DQ03
DMC0_DQ03
DMC0_DQ02
DMC0_DQ02
DMC0_DQ01
DMC0_DQ01
DMC0_DQ00
DMC0_DQ00
DMC0_DQ15
DMC0_DQ15
DMC0_DQ12
DMC0_DQ12
DMC0_DQ13
DMC0_DQ13
DMC0_DQ14
DMC0_DQ14
DMC0_BA1
DMC0_BA1
DMC0_BA2
DMC0_BA2
DMC0_A11
DMC0_A11
DMC0_DQ07
DMC0_DQ07
DMC0_DQ06
DMC0_DQ06
DMC0_DQ11
DMC0_DQ11
DMC0_DQ10
DMC0_DQ10
DMC0_DQ09
DMC0_DQ09
DMC0_DQ08
DMC0_DQ08
DMC0_UDQS
DMC0_UDQS
DMC0_UDQS
DMC0_UDQS
DMC0_A12
DMC0_A12
DMC0_A06
DMC0_A06
DMC0_A04
DMC0_A04
DMC0_LDQS
DMC0_LDQS
DMC0_LDQS
DMC0_LDQS
DMC0_CS0_Z
DMC0_CS0_Z
DMC0_BA2_Z
DMC0_BA2_Z
DMC0_BA1_Z
DMC0_BA1_Z
DMC0_BA0_Z
DMC0_BA0_Z
DMC0_A09_Z
DMC0_A09_Z
DMC0_A08_Z
DMC0_A08_Z
DMC0_A07_Z
DMC0_A07_Z
DMC0_A06_Z
DMC0_A06_Z
DMC0_A05_Z
DMC0_A05_Z
DMC0_A04_Z
DMC0_A04_Z
DMC0_A03_Z
DMC0_A03_Z
DMC0_A02_Z
DMC0_A02_Z
DMC0_A13_Z
DMC0_A13_Z
DMC0_A12_Z
DMC0_A12_Z
DMC0_A11_Z
DMC0_A11_Z
DMC0_A10_Z
DMC0_A10_Z
DMC0_A01_Z
DMC0_A01_Z
DMC0_A00_Z
DMC0_A00_Z
VREF_DMC
VREF_DMC
DMC0_WE_Z
DMC0_WE_Z
DMC0_RAS_Z
DMC0_RAS_Z
DMC0_UDQS_Z
DMC0_UDQS_Z
DMC0_CAS_Z
DMC0_CAS_Z
DMC0_ODT_Z
DMC0_ODT_Z
DMC0_UDQS_Z
DMC0_UDQS_Z
DMC0_LDQS_Z
DMC0_LDQS_Z
DMC0_UDM_Z
DMC0_UDM_Z
DMC0_LDM_Z
DMC0_LDM_Z
DMC0_DQ09_Z
DMC0_DQ09_Z
DMC0_DQ08_Z
DMC0_DQ08_Z
DMC0_DQ15_Z
DMC0_DQ15_Z
DMC0_DQ14_Z
DMC0_DQ14_Z
DMC0_DQ13_Z
DMC0_DQ13_Z
DMC0_DQ12_Z
DMC0_DQ12_Z
DMC0_DQ11_Z
DMC0_DQ11_Z
DMC0_DQ10_Z
DMC0_DQ10_Z
DMC0_CKE_Z
DMC0_CKE_Z
DMC0_DQ07_Z
DMC0_DQ07_Z
DMC0_DQ06_Z
DMC0_DQ06_Z
DMC0_DQ05_Z
DMC0_DQ05_Z
DMC0_DQ03_Z
DMC0_DQ03_Z
DMC0_DQ02_Z
DMC0_DQ02_Z
DMC0_DQ01_Z
DMC0_DQ01_Z
DMC0_DQ00_Z
DMC0_DQ00_Z
DMC0_LDQS_Z
DMC0_LDQS_Z
omitted since overall trace length is less than 2.5" for each net.DDR2 end of line terminators and VTT tracking circuit have been
and any recommendations by the memory manufacturer.For a custom design, please adhere to any EE-note from ADI
CLK termination at the memory
DSP Signals
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.03
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
U1
ADSP-BF609BGA349C80P22X22_1900X1900
T1
U2
P1
R2
P2
N1
N2
M1
M2
L1
T2
R1
L2
K1
V2
U1
AB3
Y4
V1
W2
V3
AA1
Y2
Y1
W1
AB2
P3
R3
U3
T3
AA3
W3
L3
M3
C12
C11
A4
B4
C10
C9
C8
C7
C6
A5
C5
B5
K3
C4
B6
A6
A13
B13
A12
B12
A11
B11
A10
B10
A9
B9
A8
B8
A7
B7PA13/SMC0_A18/PPI2_D13/LP1_D5
PA12/SMC0_A17/PPI2_D12/LP1_D4
PA11/SMC0_A15/PPI2_D11/LP1_D3
PA10/SMC0_A14/PPI2_D10/LP1_D2
PA09/SMC0_A12/PPI2_D09/LP1_D1
PA08/SMC0_A11/PPI2_D08/LP1_D0
PA07/SMC0_A10/PPI2_D07/LP0_D7
PA06/SMC0_A09/PPI2_D06/LP0_D6
PA05/SMC0_A08/PPI2_D05/LP0_D5
PA04/SMC0_A07/PPI2_D04/LP0_D4
PA03/SMC0_A06/PPI2_D03/LP0_D3
PA02/SMC0_A05/PPI2_D02/LP0_D2
PA01/SMC0_A04/PPI2_D01/LP0_D1
PA00/SMC0_A03/PPI2_D00/LP0_D0
PA14/SMC0_A19/PPI2_D14/LP1_D6
PA15/SMC0_A20/PPI2_D15/LP1_D7
PB12/SMC0_BG/SPT0_BTDV/SPT0_AD1/TM0_ACLK1
PB13/ETH0_TXEN/PPI1_FS1/TM0_ACI6
PB08/SMC0_A23/PPI2_D17/SPT0_BCLK
PB09/SMC0_BGH/SPT0_AD0/TM0_ACLK2
PB07/SMC0_A22/PPI2_D16/SPT0_BFS
PB06/SMC0_A21/SPT0_ATDV/TM0_ACLK4
PB05/SMC0_AMS3/SMC0_ABE1/SPT0_ACLK
PB04/SMC0_AMS2/SMC0_ABE0/SPT0_AFS
PB03/SMC0_A16/PPI2_FS3/LP1_CLK
PB02/SMC0_A13/PPI2_FS2/LP1_ACK
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PB01/SMC0_AMS1/PPI2_FS1/LP0_ACK
PB00/SMC0_NORCLK/PPI2_CLK/LP0_CLK
PB15/ETH0_PTPPPS/PPI1_FS3
PB14/ETH0_REFCLK/PPI1_CLK
PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PD13/SPI1_MOSI/TM0_ACLK5
PD08/UART0_RX/TM0_ACI0
PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD07/UART0_TX/TM0_ACI3
PD06/ETH0_PHYINT/PPI1_FS2/TM0_ACI5
PD05/SPI1_CLK/TM0_ACLK7
PD04/SPI0_CLK
PD03/SPI0_MOSI
PD02/SPI0_MISO
PD11/SPI0_SEL1/SPI0_SS
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3
PD01/SPI0_D3/PPI1_D17/SPI0_SEL2
PD00/SPI0_D2/PPI1_D16/SPI0_SEL3
PD15/SPI1_SEL2/PPI0_D21/SPT1_AD0
PD14/SPI1_MISO/TM0_ACLK6
PC14/SPI1_SEL7/PPI1_D14
PC15/SPI0_SEL4/PPI1_D15
PC00/ETH0_RXD0/PPI1_D00
PC01/ETH0_RXD1/PPI1_D01
PC10/PPI1_D10
PC11/PPI1_D11/ETH_PTPAUXIN
PC02/ETH0_TXD0/PPI1_D02
PC03/ETH0_TXD1/PPI1_D03
PC04/ETH0_RXERR/PPI1_D04
PC05/ETH0_CRS/PPI1_D05
PC06/ETH0_MDC/PPI1_D06
PC07/ETH0_MDIO/PPI1_D07
PC09/ETH1_PTPPPS/PPI1_D09
PC08/PPI1_D08
PC13/SPI0_SEL6/PPI1_D13/ETH_PTPCLKIN
PC12/SPI0_SEL7/PPI1_D12
R2710K0402
3.3V
R6510K0402
040233R245
R6710K0402
R6610K0402
R16100402
R2270402
33
U1
ADSP-BF609BGA349C80P22X22_1900X1900
J2
K2
F3
G2
H2
N3
H1
C1
C2
B1
B3
A2
A3
F1
G3
F2
H3
J3
E1
D2
D1
E3
E2
D3
C21
D21
D22
C22
Y11
Y12SYS_TDA
SYS_TDK
TWI0_SCL
TWI0_SDA
TWI1_SDA
TWI1_SCL
JTG_TCK
JTG_EMU
JTG_TMS
JTG_TDI
JTG_TDO
JTG_TRST
SYS_BMODE0
SYS_BMODE1
SYS_FAULT
SYS_BMODE2
SYS_FAULT
USB0_DP
USB0_DM
USB0_ID
USB0_VBUS
USB0_VBC
USB0_CLKIN
SYS_CLKIN
SYS_CLKOUT
SYS_XTAL
SYS_HWRST
SYS_NMI/SYS_RESETOUT
SYS_EXTWAKE
SYS_PWRGD
U1
ADSP-BF609BGA349C80P22X22_1900X1900
B16
C19
B19
C15
C18
A20
B17
C17
A19
C14
B20
A18
A17
B18
B15
A15
AB18
AA20
AA18
Y16
AA19
AB16
AA17
Y18
AB15
AB17
Y19
AB21
Y17
AA14
AB20
AB19
B22
A21
C16
D20
A14
B14
A16
C13
AA6
AB6
AA13
AB13
AA8
AB8
AA12
AB12
AA11
AB11
AA10
AB10
AB9
AA9
AB7
AA7
AA15
AA16
AA4
AB4
Y5
AA5
AB5
Y6
Y7
Y8
Y9
Y10
Y14
Y15
Y13
AB14PE13/ETH1_CRS/PWM1_CH/RSI0_D4
PE12/ETH1_PHYINT/PWM1_CL/RSI0_D5
PE11/ETH1_MDIO/PWM1_DH/RSI0_D7
PE10/ETH1_MDC/PWM1_DL/RSI0_D6
PE09/PPI0_CLK/LP2_CLK/PWM0_TRIP0
PE08/PWM0_SYNC/PPI0_FS1/LP2_ACK/ACM0_T0
PE07/SPT1_BTDV/PPI0_FS2/LP3_ACK
PE06/SPT1_ATDV/PPI0_FS3/LP3_CLK
PE05/PPI0_D23/SPT1_AFS
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE15/ETH1_RXD1/PWM1_BL/RSI0_D3
PF12/ACM0_A2/PPI0_D12/LP3_D4
PF13/ACM0_A3/PPI0_D13/LP3_D5
PF08/SPI1_SEL5/PPI0_D08/LP3_D0
PF09/SPI1_SEL6/PPI0_D09/LP3_D1
PF07/PWM0_DH/PPI0_D07/LP2_D7
PF06/PWM0_DL/PPI0_D06/LP2_D6
PF05/PWM0_CH/PPI0_D05/LP2_D5
PF04/PWM0_CL/PPI0_D04/LP2_D4
PF03/PWM0_BH/PPI0_D03/LP2_D3
PF02/PWM0_BL/PPI0_D02/LP2_D2
PF11/PPI0_D11/LP3_D3/PWM0_TRIP1
PF10/ACM0_A4/PPI0_D10/LP3_D2
PF01/PWM0_AH/PPI0_D01/LP2_D1
PF00/PWM0_AL/PPI0_D00/LP2_D0
PF15/ACM0_A1/PPI0_D15/LP3_D7
PF14/ACM0_A0/PPI0_D14/LP3_D6
SMC0_BR
SMC0_AMS0
SMC0_A2
SMC0_A1
SMC0_ARDY/SMC0_NORWT
SMC0_ARE
SMC0_AWE
SMC0_AOE/SMC0_NORDV
PG14/UART1_RX/SYS_IDLE1/TM0_ACI1
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
PG00/ETH1_RXD0/PWM1_BH/RSI0_D2
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
PG10/UART1_RTS/SPT2_BCLK
PG11/SPT2_BD1/TM0_TMR6/CNT0_UD
PG02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
PG05/ETH1_TXEN/RSI0_CMD/PWM1_SYNC/ACM0_T1
PG06/ETH1_REFCLK/RSI0_CLK/SPT2_BTDV/PWM1_TRIP0
PG07/SPT2_BFS/TM0_TMR5/CNT0_ZM
PG09/SPT2_AD0/TM0_TMR4
PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PG13/UART1_CTS/TM0_CLK
PG12/SPT2_BD0/TM0_TMR7/CNT0_DG
SMC0_D0
SMC0_D1
SMC0_D2
SMC0_D3
SMC0_D4
SMC0_D5
SMC0_D6
SMC0_D7
SMC0_D8
SMC0_D9
SMC0_D10
SMC0_D11
SMC0_D12
SMC0_D13
SMC0_D14
SMC0_D15
R2290402
0
R2280402
0
R244 330402
PE08/PWM0_SYNC/PPI0_FS1/LP2_ACK/ACM0_T0
PG05/ETH1_TXEN/RSI0_CMD/PWM1_SYNC/ACM0_T1
PF07/PWM0_DH/PPI0_D07/LP2_D7
PF05/PWM0_CH/PPI0_D05/LP2_D5
PF03/PWM0_BH/PPI0_D03/LP2_D3
PF01/PWM0_AH/PPI0_D01/LP2_D1
SMC0_AMS0
PB05/SMC0_AMS3/SMC0_ABE1/SPT0_ACLK
PB09/SMC0_BGH/SPT0_AD0/TM0_ACLK2
PB04/SMC0_AMS2/SMC0_ABE0/SPT0_AFS
PB12/SMC0_BG/SPT0_BTDV/SPT0_AD1/TM0_ACLK1
PA10/SMC0_A14/PPI2_D10/LP1_D2
PA01/SMC0_A04/PPI2_D01/LP0_D1
PA02/SMC0_A05/PPI2_D02/LP0_D2
PA14/SMC0_A19/PPI2_D14/LP1_D6
PA12/SMC0_A17/PPI2_D12/LP1_D4
PA08/SMC0_A11/PPI2_D08/LP1_D0
PA06/SMC0_A09/PPI2_D06/LP0_D6
PA04/SMC0_A07/PPI2_D04/LP0_D4
PB02/SMC0_A13/PPI2_FS2/LP1_ACK
PA11/SMC0_A15/PPI2_D11/LP1_D3
PA15/SMC0_A20/PPI2_D15/LP1_D7
PB03/SMC0_A16/PPI2_FS3/LP1_CLK
PA09/SMC0_A12/PPI2_D09/LP1_D1
PA05/SMC0_A08/PPI2_D05/LP0_D5
PA03/SMC0_A06/PPI2_D03/LP0_D3
PC14/SPI1_SEL7/PPI1_D14
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
SMC0_ARE
SMC0_D3
SMC0_D9
SMC0_D13
PA00/SMC0_A03/PPI2_D00/LP0_D0
SMC0_D11
PB01/SMC0_AMS1/PPI2_FS1/LP0_ACK
SMC0_D1
SMC0_D5
SMC0_D7
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
SMC0_D14
SMC0_A2
SMC0_D4
SMC0_D6
SMC0_D10
SMC0_D2
SMC0_D8
SMC0_D12
SMC0_D15
SMC0_AWE
SMC0_D0
PD04/SPI0_CLK
PD00/SPI0_D2/PPI1_D16/SPI0_SEL3
PD01/SPI0_D3/PPI1_D17/SPI0_SEL2
PC12/SPI0_SEL7/PPI1_D12
PD07/UART0_TX/TM0_ACI3
PD06/ETH0_PHYINT/PPI1_FS2/TM0_ACI5
PC02/ETH0_TXD0/PPI1_D02
PC04/ETH0_RXERR/PPI1_D04
PC06/ETH0_MDC/PPI1_D06
PB15/ETH0_PTPPPS/PPI1_FS3
PC01/ETH0_RXD1/PPI1_D01
PC03/ETH0_TXD1/PPI1_D03
PC05/ETH0_CRS/PPI1_D05
PC07/ETH0_MDIO/PPI1_D07
USB0_CLKIN
JTG_TDI
SYS_MODE0
SYS_MODE2
SYS_FAULT
SYS_FAULT
USB0_DP
USB0_DM
USB0_ID
SYS_CLKIN
SYS_PWRGD
JTG_TDO
SMC0_A1
SYS_MODE1
PB14/ETH0_REFCLK/PPI1_CLK
PA13/SMC0_A18/PPI2_D13/LP1_D5
PB13/ETH0_TXEN/PPI1_FS1/TM0_ACI6
PE10/ETH1_MDC/PWM1_DL/RSI0_D6
PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PF08/SPI1_SEL5/PPI0_D08/LP3_D0
PF09/SPI1_SEL6/PPI0_D09/LP3_D1
USB0_VBUS
PC00/ETH0_RXD0/PPI1_D00
PB00/SMC0_NORCLK/PPI2_CLK/LP0_CLK
PC08/PPI1_D08
PC09/ETH1_PTPPPS/PPI1_D09
PC10/PPI1_D10
PC11/PPI1_D11/ETH_PTPAUXIN
PC13/SPI0_SEL6/PPI1_D13/ETH_PTPCLKIN
PC15/SPI0_SEL4/PPI1_D15
PD02/SPI0_MISO
PD03/SPI0_MOSI
PD05/SPI1_CLK/TM0_ACLK7
PD08/UART0_RX/TM0_ACI0
PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3
PD11/SPI0_SEL1/SPI0_SS
PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PD13/SPI1_MOSI/TM0_ACLK5
PD14/SPI1_MISO/TM0_ACLK6
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PB08/SMC0_A23/PPI2_D17/SPT0_BCLK
PB07/SMC0_A22/PPI2_D16/SPT0_BFS
PB06/SMC0_A21/SPT0_ATDV/TM0_ACLK4
PA07/SMC0_A10/PPI2_D07/LP0_D7
PD15/SPI1_SEL2/PPI0_D21/SPT1_AD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE05/PPI0_D23/SPT1_AFS
PE06/SPT1_ATDV/PPI0_FS3/LP3_CLK
PE07/SPT1_BTDV/PPI0_FS2/LP3_ACK
PE09/PPI0_CLK/LP2_CLK/PWM0_TRIP0
PF00/PWM0_AL/PPI0_D00/LP2_D0
PF02/PWM0_BL/PPI0_D02/LP2_D2
PF04/PWM0_CL/PPI0_D04/LP2_D4
PF06/PWM0_DL/PPI0_D06/LP2_D6
PF10/ACM0_A4/PPI0_D10/LP3_D2
PF11/PPI0_D11/LP3_D3/PWM0_TRIP1
PF12/ACM0_A2/PPI0_D12/LP3_D4
PF13/ACM0_A3/PPI0_D13/LP3_D5
PF14/ACM0_A0/PPI0_D14/LP3_D6
PF15/ACM0_A1/PPI0_D15/LP3_D7
SMC0_ARDY/SMC0_NORWT
SMC0_BR
SMC0_BR
PG07/SPT2_BFS/TM0_TMR5/CNT0_ZM
PG09/SPT2_AD0/TM0_TMR4
PG10/UART1_RTS/SPT2_BCLK
PG11/SPT2_BD1/TM0_TMR6/CNT0_UD
PG12/SPT2_BD0/TM0_TMR7/CNT0_DG
PG13/UART1_CTS/TM0_CLK
PG14/UART1_RX/SYS_IDLE1/TM0_ACI1
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
SMC0_AOE/SMC0_NORDV
USB0_VBC
SYS_CLKOUT
SYS_XTAL
SYS_HWRST
SYS_NMI/SYS_RESETOUT
SYS_NMI/SYS_RESETOUT
SYS_EXTWAKE
TWI0_SCL
TWI1_SCL
TWI1_SCL
TWI0_SDA
TWI1_SDA
TWI1_SDA
SYS_TDA
SYS_TDK
JTG_EMU
JTG_TCK
JTG_TMS
JTG_TRST
PG02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG00/ETH1_RXD0/PWM1_BH/RSI0_D2
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG06/ETH1_REFCLK/RSI0_CLK/SPT2_BTDV/PWM1_TRIP0
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
PE11/ETH1_MDIO/PWM1_DH/RSI0_D7
PE12/ETH1_PHYINT/PWM1_CL/RSI0_D5
PE13/ETH1_CRS/PWM1_CH/RSI0_D4
PE15/ETH1_RXD1/PWM1_BL/RSI0_D3
SMC0_D[0:15]
3.3V
TP3
A0269-2011
ADSP-BF609 EZ-Board
1.04
DSP Power and Ground
1/5/12 16
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
C1190.01UF0402
C1210.01UF0402
C1220.01UF0402
C1230.01UF0402
C1240.01UF0402
C1250.01UF0402
C1260.01UF0402
C1270.01UF0402
C1280.01UF0402
U1
ADSP-BF609BGA349C80P22X22_1900X1900
F6
E5
U17
R16
R17
T16
T17
L17
M17
N17
P17
H17
J17
K17
H16
G17
G16
F17
U13
U14
U15
U16
U7
U8
U9
U10
T8
T9
T14
T15
G8
G9
G14
G15
F13
F14
F15
F16
F10
F9
F8
W12
T11
T12
T13
U6
U11
U12
M6
N6
P6
R6
R7
T6
T7
T10
G12
G13
H6
H7
J6
K6
L4
L6
G6
G7
G10
G11
F12
F11
F7D11VDD_EXT1 VDD_INT1
VDD_EXT3
VDD_EXT4
VDD_EXT8
VDD_EXT7
VDD_EXT6
VDD_EXT5
VDD_EXT16
VDD_EXT15
VDD_EXT14
VDD_EXT13
VDD_EXT12
VDD_EXT11
VDD_EXT10
VDD_EXT9
VDD_EXT24
VDD_EXT23
VDD_EXT22
VDD_EXT21
VDD_EXT20
VDD_EXT19
VDD_EXT18
VDD_EXT17
VDD_EXT30
VDD_EXT29
VDD_EXT28
VDD_EXT27
VDD_EXT26
VDD_EXT25
VDD_TD
VDD_INT2
VDD_INT3
VDD_INT4
VDD_INT8
VDD_INT7
VDD_INT6
VDD_INT5
VDD_INT12
VDD_INT11
VDD_INT10
VDD_INT9
VDD_INT16
VDD_INT15
VDD_INT14
VDD_INT13
VDD_INT20
VDD_INT19
VDD_INT18
VDD_INT17
VDD_INT24
VDD_INT23
VDD_INT22
VDD_INT21
VDD_DMC1
VDD_DMC2
VDD_DMC3
VDD_DMC4
VDD_DMC7
VDD_DMC6
VDD_DMC5
VDD_DMC11
VDD_DMC10
VDD_DMC9
VDD_DMC8
VDD_DMC15
VDD_DMC14
VDD_DMC13
VDD_DMC12
VDD_DMC16
VDD_USB
VDD_EXT2
0805
C11810UF
C1290.01UF0402
C1730.1UF0402
C1360.1UF0402
C1370.1UF0402
C1380.1UF0402
C1390.1UF0402
C1400.1UF0402
C1410.1UF0402
C1300.01UF0402
C1310.01UF0402
C1200.01UF0402
C1320.01UF0402
C1330.01UF0402
C1340.01UF0402
C1350.1UF0402
C1420.1UF0402
DNP
R16610K0402
C1440.01UF0402
C1450.01UF0402
C1460.01UF0402
C1470.01UF0402
C1480.01UF0402
C1490.01UF0402
C1500.01UF0402
C1510.01UF0402
C1520.01UF0402
C1540.1UF0402
C1650.01UF0402
C1660.01UF0402
C1740.1UF0402
C1750.1UF0402
C17810UF0805
C1760.1UF0402
04020R165
04020.1UFC115
C1430.01UF0402
04020.1UFC116
C11710UF0805
C1670.01UF0402
C1680.01UF0402
C1690.01UF0402
C1700.01UF0402
C1710.01UF0402
C1720.01UF0402
C16410UF0805
C17710UF0805
C1550.1UF0402
C1560.1UF0402
C1570.1UF0402
C1580.1UF0402
C1590.1UF0402
C1600.1UF0402
C1610.1UF0402
C1620.1UF0402
C16310UF0805
C1530.1UF0402
080510UFC114
040210KR167
R16800402
U1
ADSP-BF609BGA349C80P22X22_1900X1900
C3
B2
M4
AB22
AB1
AA22
AA21
AA2
Y20
Y3
W11
P14
P13
P12
P11
P10
P9
N15
N14
N13
N12
N11
N10
N9
N8
M19
M15
M14
M13
M12
M11
M10
M9
M8
L15
L14
L13
L12
L11
L10
L9
L8
K15
K14
K13
K12
K11
K10
K9
K8
J14
J13
J12
J11
J10
J9
J1
G1
D12
C20
B21
A22
A1GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
GND10
GND11
GND12
GND13
GND14
GND15
GND16
GND17
GND18
GND19
GND20
GND21
GND22
GND23
GND24
GND25
GND26
GND27
GND28
GND29
GND30
GND31
GND32
GND33
GND34
GND35
GND36
GND37
GND38
GND39
GND40
GND41
GND42
GND43
GND44
GND45
GND46
GND47
GND48
GND49
GND50
GND51
GND52
GND53
GND54
GND55
GND56
GND57
GND58
GND59
GND60
GND61
GND62
GND63
VDD_DMC VDD_DMC
VDD_DMC
VDD_INT
VDD_INT
VDD_INT
VDD_INTVDD_INT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXTVDD_EXT
VDD_USB
VDD_TD
IDC
P16
IDC3X2_SMT
1
3
65
4
2
U2
48MHZOSC003
2
4
31STANDBY OUT
VDD
GND
DNP
R710K0402
04020.01UFC19
D9
ESDA6V1SCSOT95P280-6N
4 5
23
1
6IN3
IN0
IN1 GND0
GND1IN2
Temp. Sensor, Boot Switch, DSP Clock, USB Conn
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.05
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
U10
PI3A125SC70_5
2 4
1OE
BA
R16200402
R1VARISTOR
0603
USB_MINI-AB
P7
CON052
1
6
4
5
2
3D+
D-
GND
ID
SHELL
VBUS
C240.01UF0402
TP11
TP23.3V
3.3V
3.3V
040233R8
3.3V
3.3V
R1810K0402
C220.01UF0402
3.3V
3.3V
R21100805
R13330402
3.3V
3.3V
3.3V
C2118PF0402DNP
DNP
Y125MHzOSC013
TP1
R1010K0402
R1110K0402
R13600402
R161.50K0402
DNP
C2018PF0402
C230.01UF0402
ADM1032
U54
SOIC_N8ADM1032
4
6
1
7
8
5
2
3D_MINUS
D_PLUS
GND
SCK
SI
VCC
ALERT
THERM
C254.7UF0805
C260.01UF0402
R1210K0402
R151.50K0402
R1710K0402
R191M0603
R910K0402
R209THERM
1206
D10
ESD7004DFN50P250X100-10N
7
6
10
9
4 8
32
1
5IN3
IN0
IN1 GND0
GND1IN2
NC2
NC3
NC0
NC1FER16001206
3.3V
SW2
ROTARYSWT027
4
2
1C
0
12
3
4
56
7
DNP
R21200402
C270.01UF0402
C280.01UF0402
C290.01UF0402
C300.01UF0402
C310.01UF0402
C320.01UF0402
C330.01UF0402
R2010K0402
R21300402DNP
IDC
P17
IDC3X2_SMT
1
3
65
4
2
U9
PI3A125SC70_5
2 4
1OE
BA
R2110K0402
3.3V
TP10
DNP
Y224MHzOSC013
040218PFC193
DNP
3.3V
R133
040210K
R134
040210K
3.3V
R13510K0402
U42
25MHZOSC003
2
4
31STANDBY OUT
VDD
GND
R14
04020
DNP
USB_VBUS
PB15/ETH0_PTPPPS/PPI1_FS3
PB15/ETH0_PTPPPS/PPI1_FS3
USB0_CLKIN
USB0_CLKIN
SYS_MODE0
SYS_MODE2
SYS_FAULT
SYS_FAULT
USB0_DP
USB0_DM
USB0_ID
SYS_CLKIN
SYS_CLKIN
SYS_PWRGD
TEMP_IRQ
TEMP_IRQ
TEMP_THERM
TEMP_THERM
SYS_MODE1
TEMP_IRQ_EN
TEMP_THERM_EN
USB0_VBUS
PC09/ETH1_PTPPPS/PPI1_D09
PC11/PPI1_D11/ETH_PTPAUXIN PC13/SPI0_SEL6/PPI1_D13/ETH_PTPCLKIN
PG09/SPT2_AD0/TM0_TMR4
SYS_XTAL
SYS_NMI/SYS_RESETOUT
SYS_EXTWAKE
SYS_EXTWAKE
TWI0_SCL
TWI0_SDA
SYS_TDA
SYS_TDK
UART0 slave boot
DSP OSC
USB OSC
USB OSC
OPTIONAL DSP CRYSTAL
"USB OTG"
111
SW1: Boot mode selection switch
DEFAULT
LP0 slave boot
reserved
SPI0 slave boot
SPI0 master boot
RSI master boot
Parrallel Flash boot
No-boot/Idle
110
101
100
011
010
001
000
BMODE[2:0]
10KR222
DNP0402
R223
040210K
DNP
U44
PC28F128P33BEBGA64
E8
F1
B8
B3
C6
G8
D4
F8
B4
F6
F7
A4
G4
D6
D5
H3
A6
H8
B6
H1
G2
H6
H2
H4
B2
E3
E1
H7
G6
G5
E5
E4
G3
E7
G7
H5
F5
F4
F3
E2
F2
E6
A3
C2
A2
D2
D1
C1
G1
A8
C8
C7
B1
B7
A7
D8
D7
C5
B5
A5
C4
D3
C3
A1 A1
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A2
A20
A21
A22
A23
A3
A4
A5
A6
A7
A8
CLK
D0
D1
D10
D11
D12
D13
D14
D15
D2
D3
D4
D5
D6
D7
D8
D9
GN
D1
GN
D2
GN
DQ
1G
ND
Q2
NC4
NC5
NC6
NC7
VC
C1
VC
C2
VC
CQ
1V
CC
Q2
VC
CQ
3
VPEN
WAIT
ADV
CE
OE
RST
WE
WP
A9
NC2
NC3
NC1
U38
W25Q32SO8W
3
7
1
8
25
6
4GND
SCK
SI SO
VCC
CS
HOLD
WP
Memory
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.06
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
040210KR26
040210KR25
040210KR24
040210KR23
R137330402
3.3V
DNP
R3610K0402
C350.01UF0402
3.3V
R2810K0402 R138
330402
R3110K0402
3.3V
R2910K0402
C360.01UF0402
C370.01UF0402
040210KR22
3.3V
DNP
R3510K0402
C380.01UF0402
3.3V
R37 330402
3.3V
R34330402
R38 330402
33RNS003
RN14
98
107
116
125
134
143
152
161R1A R1B
R2A R2B
R3A R3B
R4A R4B
R5A R5B
R6A R6B
R7A R7B
R8A R8B
R4010K0402
R4110K0402
SD_CONN
J5
CON067
14
15
194
16
24
23
22
17
20
2827211863
13
12
11
10
1
9
8
7
2
5 CLK
CMD
DAT0
DAT1
DAT2
DAT3
DAT4
DAT5
DAT6
DAT7
GN
D1
GN
D2
GN
D3
GN
D4
GN
D5
GN
D6
MINI_SD_CLK
MINI_SD_CMD
MINI_SD_DAT0
MINI_SD_DAT1
MINI_SD_DAT2
MINI_SD_DAT3
VD
D1
VD
D2
CD
WP
C3910UF0805
C400.01UF0402
3.3V
3.3V
R3010K0402
R3210K0402
R3910K0402
C340.01UF0402
R3310K0402
R4210K0402
SC70_5PI3A125
U15
2 4
1OE
BA
SC70_5PI3A125
U14
2 4
1OE
BA
SC70_5PI3A125
U13
2 4
1OE
BA
SC70_5PI3A125
U12
2 4
1OE
BA
SC70_5PI3A125
U11
2 4
1OE
BA
U59
SN74LVC1G04SOT23-5
DNP
R13900402
PG05/ETH1_TXEN/RSI0_CMD/PWM1_SYNC/ACM0_T1
SMC0_AMS0
SMC0_ARE
SMC0_D3
SMC0_D9
SMC0_D13
SMC0_D11
SMC0_D1
SMC0_D5
SMC0_D7
SMC0_D14
SMC0_A2
SMC0_D4
SMC0_D6
SMC0_D10
SMC0_D2
SMC0_D8
SMC0_D12
SMC0_D15
SMC0_AWE
SMC0_D0
PD04/SPI0_CLK
PD00/SPI0_D2/PPI1_D16/SPI0_SEL3
PD01/SPI0_D3/PPI1_D17/SPI0_SEL2
SD_CD
SD_CD
SD_WP
SD_WP
SPIFLASH_CS
SPIFLASH_CS
SPIFLASH_SPI0D2
SPIFLASH_SPI0D2
SPIFLASH_SPI0D3
SPIFLASH_SPI0D3
MMC_D0
MMC_D0
MMC_D1
MMC_D1
MMC_D2
MMC_D2
MMC_D3
MMC_D3
MMC_D4
MMC_D4
MMC_D5
MMC_D5
MMC_D6
MMC_D6
MMC_D7
MMC_D7
SMC0_A1
PE10/ETH1_MDC/PWM1_DL/RSI0_D6
SD_WP_EN
SD_CD_EN
SPI0D3_EN
SPI0D2_EN
SPIFLASH_CS_EN
PD02/SPI0_MISOPD03/SPI0_MOSI
PD11/SPI0_SEL1/SPI0_SS
PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PB08/SMC0_A23/PPI2_D17/SPT0_BCLK
PB07/SMC0_A22/PPI2_D16/SPT0_BFS
PB06/SMC0_A21/SPT0_ATDV/TM0_ACLK4
SMC0_ARDY/SMC0_NORWT
PG10/UART1_RTS/SPT2_BCLK
PG13/UART1_CTS/TM0_CLK
SMC0_AOE/SMC0_NORDV
SYS_NMI/SYS_RESETOUT
PA00/SMC0_A03/PPI2_D00
PA01/SMC0_A04/PPI2_D01
PA02/SMC0_A05/PPI2_D02
PA03/SMC0_A06/PPI2_D03
PA04/SMC0_A07/PPI2_D04
PA05/SMC0_A08/PPI2_D05
PA06/SMC0_A09/PPI2_D06
PA07/SMC0_A10/PPI2_D07
PB00/SMC0_NORCLK/PPI2_CLK
PA08/SMC0_A11/PPI2_D08
PA09/SMC0_A12/PPI2_D09
PA10/SMC0_A14/PPI2_D10
PA11/SMC0_A15/PPI2_D11
PA12/SMC0_A17/PPI2_D12
PA13/SMC0_A18/PPI2_D13
PA14/SMC0_A19/PPI2_D14
PA15/SMC0_A20/PPI2_D15
PB02/SMC0_A13/PPI2_FS2
PB03/SMC0_A16/PPI2_FS3
PG02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG00/ETH1_RXD0/PWM1_BH/RSI0_D2
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG06/ETH1_REFCLK/RSI0_CLK/SPT2_BTDV/PWM1_TRIP0
PE11/ETH1_MDIO/PWM1_DH/RSI0_D7
PE12/ETH1_PHYINT/PWM1_CL/RSI0_D5
PE13/ETH1_CRS/PWM1_CH/RSI0_D4
PE15/ETH1_RXD1/PWM1_BL/RSI0_D3SMC0_D[0:15]
32Mb QUAD SPI FLASH
SD CARD
(16M x 16)32 MB BURST FLASH
"SD CARD"
10K0402
R48
C450.1UF0402
R54 330402
R5710K0402
C410.1UF0402
C430.1UF0402
UART0
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.07
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
U39
ADM3315TSSOP24
22
24
19
5
13
16
12
9
14
15
17
18
21
1
11
10
8
7
4
2
20
6C1+
C1-
C2+
C2-
T1IN
T2IN
R1OUT
R2OUT
V+
V-
T1OUT
T2OUT
R1IN
R2IN
T3IN
R3OUT
T3OUT
R3IN
EN
SD
C3+
C3-
U16
PI3A125SC70_5
2 4
1OE
BA
U17
PI3A125SC70_5
2 4
1OE
BA
U18
PI3A125SC70_5
2 4
1OE
BA
U19
PI3A125SC70_5
2 4
1OE
BA
U20
PI3A125SC70_5
2 4
1OE
BA
U21
PI3A125SC70_5
2 4
1OE
BA
C460.01UF0402
R55 330402
R5610K0402
3.3V
R5210K0402
J2
DB9CON038
9
8
7
6
5
4
3
2
1C420.1UF0402
3.3V
C440.1UF0402
C470.01UF0402
R4310K0402
3.3V
R4610K0402
R4710K0402
R5010K0402
R53 00402
C490.01UF0402
C500.01UF0402
C510.01UF0402
C520.01UF0402
R5110K0402
DNP
R4910K0402
3.3V
R4510K0402
R4410K0402
3.3V
3.3V
C480.01UF0402
3.3V
PD07/UART0_TX/TM0_ACI3
CTS
UART0CTS_EN
UART0CTS_146_EN
UART0CTS_RST_EN
UART0CTS_RTS_LPBK
UART0RX_EN
UART0RTS_EN
UART0_DTR_DCD_DSR
PD08/UART0_RX/TM0_ACI0
PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3
UART 0
"DCE"
U30
PI3A125SC70_5
2 4
1OE
BA
U32
PI3A125SC70_5
2 4
1OE
BA
U34
PI3A125SC70_5
2 4
1OE
BA
CAN and Rotary Encoder
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.08
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
R21010K0402
3.3V
DNP
R14710K0402
R151100603
J4
RJ11CON039
4
3
2
1
DNP
R15010K0402
C1070.01UF0402
R14810K0402
C109100PF0603
R152100603
R15462.00603
R1551.0K0402
R15362.00603
C108100PF0603
C1104700PF0603
R14910K0402
U55
TJA1041SOIC14
14 9
5 3 10
1
114
7
2
8
6
12
13CANH
CANL
EN
ERR
GN
D
INH
RXD SPLIT
TXD
VB
AT
VD
D
VIO
WAKESTB
5V 3.3V
3.3V
3.3V 5V
R1561.0K0402
R1571.0K0402
C1110.01UF0402
3.3V3.3V3.3V
C1050.01UF0402
3.3VR14610K0402
C1040.01UF0402
C1060.01UF0402
C1130.01UF0402
R15810K0402
R16010K0402
SW9
ROTARY_ENC_EDGESWT025
4
5
2
6
1 A
B
COMMON
SW1
SW2
C1120.01UF0402
3.3V
U33
PI3A125SC70_5
2 4
1OE
BA
R15910K0402
U31
PI3A125SC70_5
2 4
1OE
BA
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
CAN_STB
CAN_EN
CNT0ZM_EN
CNT0DG_EN
CAN0RX_EN
CAN0_ERR_EN
CAN0RXCAN0RX
CAN0_ERR
CAN0_ERR
CNT0UD_EN
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PG07/SPT2_BFS/TM0_TMR5/CNT0_ZM
PG11/SPT2_BD1/TM0_TMR6/CNT0_UD
PG12/SPT2_BD0/TM0_TMR7/CNT0_DG
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
"CAN"
CAN 0
ROTARY ENCODER
R173330402
U35
SC70_5PI3A125
2 4
1OE
BA
Ethernet
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.09
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
R1912.21K0603
R177 49.90402
04020.01UFC183
SHGND2
2.21K0603
R1992.21K0603
R204 R207
06032.21K
R20000805
06032.21KR208
C1910.1UF0402
R19349.90402
R192107.00805
C1880.1UF0402
R198165.00603
R19449.90402
R19549.90402
R19649.90402
RJ45
J1
CON065
14
13
11
10
9
8
7
6
5
4
3
2
12
1
LED1
LED2
SHIELD1
SHIELD2
C1900.1UF0402
3.3V
3.3V
C18710UF0805
10KR205
0402
04020.01UFC185
3.3V
R178 49.90402R179 49.90402R180 49.90402R181 49.90402
040210KR169
04020.01UFC181
U43
50MHZOSC012
4
31
2GND
OE OUT
VDD
SHGND2
R1751.50K0402
04020.01UFC184
R176 49.90402
0603
R2022.21K
0603
R2012.21K
3.3V
R184 49.90402
R182 49.90402
LED8GREENLED001
R1872.21K0603
U4
SN74CB3Q3245TSSOP20
2010
19
11
12
13
14
15
16
17
18
9
8
7
6
5
4
3
2A1
A2
A3
A4
A5
A6
A7
A8
B1
B2
B3
B4
B5
B6
B7
B8
OE
GND
VCC
R18810K0402
C1860.1UF0402
C1890.1UF0402
R1894.87K0402
R197165.00603
040210KR174
3.3V
R183 49.90402
3.3V
U5
SN74CB3Q3245TSSOP20
2010
19
11
12
13
14
15
16
17
18
9
8
7
6
5
4
3
2A1
A2
A3
A4
A5
A6
A7
A8
B1
B2
B3
B4
B5
B6
B7
B8
OE
GND
VCC
04020.01UFC182
R2032.21K0603
R20610K0402
R190107.00805
R1862.21K0603
3.3V
3.3V
R185220.00603
040210KR170
3.3V
04020.01UFC179
04020.01UFC180
3.3V
R172330402
TP28
TP4
3.3V
3.3V
3.3V
DNP040210KR171
U49
DP83848LQFP48
23
37
18
19
29
33
34
2
1
17
16
6
5
4
3 11
10
9
12
841
39
38
14
1346
45
44
43
21
20
24
7
30
31
27
28
26
48324735 36
40
42
2215
25 25MHZ_OUT
AG
ND
1A
VD
D
COL/PHYAD0
CRS/CRS_DV/LED_CFG
DG
ND
IOG
ND
1
IOG
ND
2IO
VD
D1
IOV
DD
2
LED_ACT/AN_EN
LED_LINK/AN0
LED_SPEED/AN1
MDC
MDIO
PWR_DOWN/INT
RBIAS
RESERVED1
RESERVED2
RXD0/PHYAD1
RXD1/PHTAD2
RXD2/PHYAD3
RXD3/PHYAD4 RXN
RXP
RX_CLK
RX_DV/MII_MODE
RX_ER/MDIX_EN TCK
TDI
TDO
TMS
TRSTTXD0
TXD1
TXD2
TXD3/SNI_MODE
TXN
TXP
TX_CLK
TX_EN
X1
X2
RESET
AG
ND
2
PFBIN1
PFBIN2
PFBOUT
3.3V
PD06/ETH0_PHYINT/PPI1_FS2/TM0_ACI5
PC02/ETH0_TXD0/PPI1_D02
PC04/ETH0_RXERR/PPI1_D04
PC06/ETH0_MDC/PPI1_D06
PC01/ETH0_RXD1/PPI1_D01
PC03/ETH0_TXD1/PPI1_D03
PC05/ETH0_CRS/PPI1_D05
PC07/ETH0_MDIO/PPI1_D07
PB14/ETH0_REFCLK/PPI1_CLK
RMII_CLK_EN
PB13/ETH0_TXEN/PPI1_FS1/TM0_ACI6
PHYAD4
PHYAD4
PHYAD3
PHYAD3
PHYAD0
PHYAD0
PHYINT_EN
MII_MODE
MII_MODE
SNI_MODE
SNI_MODE
ET0RXERR_Z
ET0RXERR_Z
PHY_CLKIN
PHY_CLKIN
PHY_PWR_DWN_INT
PHY_PWR_DWN_INT
PD06/ETH0_PHYINT_Z
PD06/ETH0_PHYINT_Z
PD06/ETH0_PHYINT_Z
ETHERNET_EN
ETHERNET_EN
ET0RXD1_Z
ET0RXD1_ZET0RXD1_Z
ET0RXD0_Z
ET0RXD0_Z
ET0RXD0_Z
ET0CRS_Z
ET0CRS_Z
ET0TXD0_Z
ET0TXD0_Z
ET0TXD1_Z
ET0TXD1_Z
ET0TXEN_Z
ET0TXEN_Z
ET0MDC_ZET0MDC_Z
ET0MDIO_Z
ET0MDIO_ZET0MDIO_Z
PC00/ETH0_RXD0/PPI1_D00
SYS_HWRST
PHY Address is 00001
OSC
PHY OSC
"SPEED"
DNP040210KR68
IDC1X1DNP
TP9
3.3V
ZU1
DS28E01TSOC6
2
1GND
IO
JTAG, Linkport 0 and 1
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.010
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
ERM8
P8
ERM8_10X2_SMT
1
3
5
7
9
11
13
15
17
1920
18
16
14
12
10
8
6
4
2MSC1
GND1
MSC2
GND2
MSC3
MSC4
MSC5
MSC6
GND3
GND4 CLK
ACK
D0
D1
D2
D3
D4
D5
D6
D7
LINKPORT_EDGE_M
R5810K0402
R5910K0402
R6010K0402
R6110K0402
IDC
P1
IDC7x2_SMTA
14
12
10
8
6
4
2
13
11
9
7
5
3
1
SW3
DIP2SWT020
3
4
2
1 12
ON
3.3V3.3V
ZP1
IDC7x2_SMTA
14
12
10
8
6
4
2
13
11
9
7
5
3
1R6310K0402
SW1
DIP8SWT016
9
10
11
12
13
14
15
16
4
5
6
3
7
2
1
8 81
24
56
7
ON
3
R6210K0402
SW5
DIP2SWT020
3
4
2
1 12
ON
SW4
DIP2SWT020
3
4
2
1 12
ON
R644.7K0402
ERF8
J3
ERF8_10X2_SMT
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2MSC1
GND1
MSC2
GND2
MSC3
MSC4
MSC5
MSC6
GND3
GND4
D7
D6
D5
D4
D3
D2
D1
D0
ACK
CLK
LINKPORT_EDGE_F
JTG_TDI
JTG_TDI
JTG_TDO
LP0_D0
LP0_D1
LP0_D2
LP0_D3
LP0_D4
LP0_D5
LP0_D6
LP0_D7
LP1_D0
LP1_D1
LP1_D2
LP1_D4
LP1_D6
LP1_D7
LP0CK
LP0ACK LP1ACK
LP1CK
TDO_IN
TDO_IN
TDO_IN
TCK_LINKPORTTCK_LINKPORT
TCK_LINKPORT
TMS_LINKPORT
TMS_LINKPORTTMS_LINKPORT
EMU_LINKPORT
EMU_LINKPORTEMU_LINKPORT
TRST_LINKPORT
TRST_LINKPORTTRST_LINKPORT
TDO_OUT
TDO_OUT
TRST_LOCAL
TRST_LOCAL
TDI_LOCAL
TDI_LOCAL
TDO_LOCAL
TDO_LOCAL
TDO_LOCAL
LP1_D5
TCK_LOCALTCK_LOCAL
TMS_LOCAL
TMS_LOCAL
EMU_LOCAL
EMU_LOCAL
JTG_EMU
JTG_TCK
JTG_TMS
JTG_TRST
LP1_D3
LINK PORT 0 / JTAG OUT LINK PORT 1 / JTAG IN
OFFONOFF
SW5.2SW5.1
SW4.1SW4.2
ONOFF
ON
ONOFF
TO EMULATORBOARD ATTACHED
TO EMULATORBOARD(S) NOT ATTACHED
TO EMULATORBOARD ATTACHED
SWITCHON
SINGLE PROCESSOR JTAG SETTINGS USING TWO OR MORE EZ-BOARDS (LINK PORT CABLESREQUIRED FOR MORE THAN TWO BOARDS)
MULTI PROCESSOR JTAG SETTINGS VIA HP-USB EMUALTOR
EMUALTOR OR DEBUG AGENT (DEFAULT)
OFFON
OFFON
ONONONON
OFFONOFF
SWITCH
"JTAG"
SW1.1
SW1.8SW1.7SW1.6SW1.5SW1.4SW1.3SW1.2
SW3.1SW3.2
SW4.2
SW5.1SW5.2
SW4.1
SW3.2SW3.1
ONOFFONOFF
ONOFF
OFFOFF
ONONONON
OFFONOFFONOFFONOFFON
OFF
JTAG SWITCHES
OFF
SW1.8SW1.7SW1.6SW1.5SW1.4SW1.3SW1.2SW1.1
U52
SN74LVC1G08SOT23-5
42
1
SC70_5PI3A125
U27
2 4
1OE
BA
U23
PI3A125SC70_5
24
1OE
B A
U53
SN74LVC1G08SOT23-5
42
1
LED7REDLED001
C600.01UF0402
C590.01UF0402
R21910K0402
R22010K0402
U22
PI3A125SC70_5
24
1OE
B A
U26
PI3A125SC70_5
2 4
1OE
BA
R7110K0402
R6910K0402
3.3V
C610.01UF0402
C570.01UF0402
3.3V
R74330.00402
R75330.00402
R21810K0402
U3
74LVC14ASOIC14
21
Push Buttons, Reset, LEDs
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.011
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
R86330402
04020.01UFC58
3.3V
04020.01UFC192
3.3V
U3
74LVC14ASOIC14
43
0402330.0R79
040210KR81
R140
040233
3.3V
040210KR80
3.3V
R76330.00402
R77330.00402
R78330.00402
C530.01UF0402
R73330.00402
LED3YELLOWLED001
LED2YELLOWLED001
LED1YELLOWLED001
3.3V
LED5YELLOWLED001
LED6GREENLED001
040210KR94
040210KR89
3.3V
3.3V
C631UF0402
C621UF0402
040210KR90
040210KR91
R881000402
R142
040210K
C640.01UF0402
R871000402
U3
74LVC14ASOIC14
65
3.3V
R85330402
U3
74LVC14ASOIC14
89
U3
SOIC1474LVC14A
1011
SW7MOMENTARYSWT024
SW8MOMENTARYSWT024
U48
ADM708SARZSOIC8
7
5
1 8
4PFI
RESETMR
PFO
RESET
040210KR93
LED4YELLOWLED001
U25
PI3A125SC70_5
2 4
1OE
BA
040210KR92
U24
PI3A125SC70_5
2 4
1OE
BA
R7010K0402
R7210K0402
U8
IDT74FCT3244APYSSOP20
19
1
3
5
7
9
17
15
13
11
12
14
16
18
8
6
4
21A1
1A2
1A3
1A4
1Y1
1Y2
1Y3
1Y4
2A1
2A2
2A3
2A4
2Y1
2Y2
2Y3
2Y4
OE1
OE2
C550.01UF0402
C560.01UF0402
040210KR82
SW6MOMENTARYSWT024
040210KR83
040210KR84
R22110K0402
C540.01UF0402
3.3V
3.3V
U7
PI3A125SC70_5
24
1OE
B A
C940.01UF0402
3.3V
R9510K0402
C93
04021UF
3.3V
R141
0402100
SW10
SWT024MOMENTARY
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
TEMP_THERM
CTS
UART0_DTR_DCD_DSR
LED1_GPIO1_EN
LED2_GPIO2_EN
LED3_GPIO3_EN
LED4_GPIO4_EN
PUSHBUTTON2_EN
PUSHBUTTON1_EN
WAKE_PUSHBUTTON_EN
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PG14/UART1_RX/SYS_IDLE1/TM0_ACI1
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
SYS_HWRST
PE12/ETH1_PHYINT/PWM1_CL/RSI0_D5
"RESET"
POWER
"RESET"
LABEL "PB1"
LABEL "PB2"
3.3V
0402
C680.01UF
C740.01UF0402
C750.01UF0402
3.3V
3.3V
C760.01UF0402C82
0.01UF0402
C770.01UF0402
040210KR108
C690.01UF0402
C780.01UF0402
C700.01UF0402
C710.01UF0402
3.3V
C790.01UF0402
C800.01UF0402
C720.01UF0402
3.3V
040210KR96
3.3V
C730.01UF0402C81
0.01UF0402
C650.01UF0402 DNP
040210KR102
U40
PI3LVD512QFN50P350X900-43N
42
41
19
17
4331 4022134 7
27
29
1
12
30
28
2
3
5
6
8
9
10
11
36
23
25
38
24
37
26
39
35
16
33
20
34
18
21
32
15
14A8
A9
3B2
9B2
9B1
3B1
8B2
2B2
8B1
2B1
0B1
6B1
0B2
6B2
1B1
7B1
7B2
1B2
A7
A6
A5
A4
A3
A2
A1
A0
4B2
4B1
SEL
VD
D0
5B1
5B2
VD
D2
VD
D1
VD
D3
VD
D4
VD
D6
VD
D5
GN
D
NC0
NC1
NC2
NC3
U41
PI3LVD512QFN50P350X900-43N
42
41
19
17
4331 4022134 7
27
291
12
30
28
2
3
5
6
8
9
10
11
36
23
25
38
24
37
26
39
35
16
33
20
34
18
21
32
15
14A8
A9
3B2
9B2
9B1
3B1
8B2
2B2
8B1
2B1
0B1
6B1
0B2
6B2
1B1
7B1
7B2
1B2
A7
A6
A5
A4
A3
A2
A1
A0
4B2
4B1
SEL
VD
D0
5B1
5B2V
DD
2
VD
D1
VD
D3
VD
D4
VD
D6
VD
D5
GN
D
NC0
NC1
NC2
NC3
3.3V
040210KR109
040210KR110
C670.01UF0402
3.3V
C660.01UF0402
3.3V
040210KR98
DNP040210KR99
DNP
040210KR101
3.3V
040210KR100
040210KR103
DNP
U45
MCP23017QFN65P600X600-29N
17
18
19
20
5
8
9
14
16
15
11
12
28
24
23
27
22
26
21
25
1
2
3
413A2 GPB7
GPB6
GPB5
GPB4
GPB0
GPA4
GPB1
GPA5
GPB2
GPA6
GPA7
GPB3
A1
A0
INTB
INTA
RESET
SDA
SCL
VDD
GPA3
GPA2
GPA1
GPA0
SoftConfig Switches, IO Extender ICs
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.012
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
DNP
R11610K0402
DNP040210KR97
R10510K0402
DNP040210KR106
040210KR104
040210KR107
3.3V
U46
MCP23017QFN65P600X600-29N
17
18
19
20
5
8
9
14
16
15
11
12
28
24
23
27
22
26
21
25
1
2
3
413A2 GPB7
GPB6
GPB5
GPB4
GPB0
GPA4
GPB1
GPA5
GPB2
GPA6
GPA7
GPB3
A1
A0
INTB
INTA
RESET
SDA
SCL
VDD
GPA3
GPA2
GPA1
GPA0
040210KR111
040210KR113
040210KR115
DNP
U47
MCP23017QFN65P600X600-29N
17
18
19
20
5
8
9
14
16
15
11
12
28
24
23
27
22
26
21
25
1
2
3
413A2 GPB7
GPB6
GPB5
GPB4
GPB0
GPA4
GPB1
GPA5
GPB2
GPA6
GPA7
GPB3
A1
A0
INTB
INTA
RESET
SDA
SCL
VDD
GPA3
GPA2
GPA1
GPA0
3.3V
DNP
R11710K0402
U3
74LVC14ASOIC14
1213
R143
040210K
DNP
3.3V
R230
040210K
SC70_5PI3A125
U28
2 4
1OE
BA
SC70_5PI3A125
U29
2 4
1OE
BA
040210KR114
DNP
DNP040210KR112
3.3V
3.3V
C830.01UF0402
PA10/SMC0_A14/PPI2_D10/LP1_D2
PA01/SMC0_A04/PPI2_D01/LP0_D1
PA02/SMC0_A05/PPI2_D02/LP0_D2
PA14/SMC0_A19/PPI2_D14/LP1_D6
PA12/SMC0_A17/PPI2_D12/LP1_D4
PA08/SMC0_A11/PPI2_D08/LP1_D0
PA06/SMC0_A09/PPI2_D06/LP0_D6
PA04/SMC0_A07/PPI2_D04/LP0_D4
PB02/SMC0_A13/PPI2_FS2/LP1_ACK
PA11/SMC0_A15/PPI2_D11/LP1_D3
PA15/SMC0_A20/PPI2_D15/LP1_D7
PB03/SMC0_A16/PPI2_FS3/LP1_CLK
PA09/SMC0_A12/PPI2_D09/LP1_D1
PA05/SMC0_A08/PPI2_D05/LP0_D5
PA03/SMC0_A06/PPI2_D03/LP0_D3
PA00/SMC0_A03/PPI2_D00/LP0_D0
PB01/SMC0_AMS1/PPI2_FS1/LP0_ACK
SYS_MODE0
LP0_D0
LP0_D1
LP0_D2
LP0_D3
LP0_D4
LP0_D5
LP0_D6
LP0_D7
LP1_D0
LP1_D1
LP1_D2
LP1_D4
LP1_D6
LP1_D7
LP0CK
LP0ACK
LP1ACK
LP1CK
CAN_STB
CAN_EN
UART0CTS_EN
UART0CTS_146_EN
UART0CTS_RST_EN
UART0CTS_RTS_LPBK
UART0RX_EN
UART0RTS_EN
CNT0ZM_EN
CNT0DG_EN
CAN0RX_EN
CAN0_ERR_EN
TEMP_IRQ_EN
TEMP_THERM_EN
LED1_GPIO1_EN
LED2_GPIO2_EN
LED3_GPIO3_EN
LED4_GPIO4_EN
PUSHBUTTON2_EN
PUSHBUTTON1_EN
CNT0UD_EN
PA13/SMC0_A18/PPI2_D13/LP1_D5
SMC0_EPPI2_LP1_SWITCH
SMC0_EPPI2_LP1_SWITCH
RMII_CLK_EN
PHYAD0
PHYINT_EN
PHY_PWR_DWN_INT
ETHERNET_EN
OVERRIDE_EBIU_LP0_BOOT
OVERRIDE_EBIU_LP0_BOOT
SMC0_LP0_EN
SMC0_LP0_EN
OVERRIDE_SMC0_LP0_BOOT
OVERRIDE_SMC0_LP0_BOOT
OVERRIDE_SMC0_LP0_BOOT
LP1_D5
U41_SEL
SD_WP_EN
SD_CD_EN
SPI0D3_EN
SPI0D2_EN
SPIFLASH_CS_EN
WAKE_PUSHBUTTON_EN
PD4_SPI0CK_EI3_EN
PD2_SPI0MISO_EI3_EN
PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3_EN
PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3_EN
PD3_SPI0MOSI_EI3_EN
PB00/SMC0_NORCLK/PPI2_CLK/LP0_CLK
PA07/SMC0_A10/PPI2_D07/LP0_D7
SYS_HWRST
SYS_HWRST
SYS_HWRST
TWI0_SCL
TWI0_SCL
TWI0_SCL
TWI0_SDA
TWI0_SDA
TWI0_SDA
LP1_D3
PA00/SMC0_A03/PPI2_D00
PA01/SMC0_A04/PPI2_D01
PA02/SMC0_A05/PPI2_D02
PA03/SMC0_A06/PPI2_D03
PA04/SMC0_A07/PPI2_D04
PA05/SMC0_A08/PPI2_D05
PA06/SMC0_A09/PPI2_D06
PA07/SMC0_A10/PPI2_D07
PB00/SMC0_NORCLK/PPI2_CLK
PB01/SMC0_AMS1/PPI2_FS1
PA08/SMC0_A11/PPI2_D08
PA09/SMC0_A12/PPI2_D09
PA10/SMC0_A14/PPI2_D10
PA11/SMC0_A15/PPI2_D11
PA12/SMC0_A17/PPI2_D12
PA13/SMC0_A18/PPI2_D13
PA14/SMC0_A19/PPI2_D14
PA15/SMC0_A20/PPI2_D15
PB02/SMC0_A13/PPI2_FS2
PB03/SMC0_A16/PPI2_FS3
I2C address 0100 011
I2C address 0100 001I2C address 0100 010
BOOT[0] OVERRIDE_SMC0_ SMC0_LP0_EN U41 output
0
1
0
1
ISOLATE MODE FOR PHY (SET TO OUTPUT LOW)
0
1
1
0
X
0
X
1
LP0
LP0
SMC0_EPPI2
SMC0_EPPI2
U41 output selection table
LP0_BOOT
5V
3.3V
P1A
HIROSE_FX8-120P-SV1(91)
101
100
71
70
120
118
116
114
112
110
108
106
104
102
98
96
94
92
90
88
86
84
82
80
78
76
74
72
119
117
115
113
111
109
107
105
103
99
97
95
93
91
89
87
85
83
81
79
77
75
73
69
66
6867
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
53
51
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37 38SPI0_SEL_CSPI0_SEL_B
SPORT1_D1
SPORT0_TDV
PPI_FS1
RSVD5
GND6
RSVD2
PPI0_D3
GND5
PPI0_D9
PPI0_D13
SPORT0_D1
SPORT1_TDV
GND7
PPI0_FS3
RSVD4
PPI0_D11
RSVD3
PPI0_D1
PPI0_D5
PPI0_D7
SPI0_D2 SPI0_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI0_RDY
GND11
RSVD8
TWI0_A0*
SPI0_SEL1/SPI0_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RSVD6
RSVD7
RSVD9
RESET_IN*
UART0_RX
PPI0_D17
PPI0_D14
VIN
GND1
USB_VCC
PPI0_D23
PPI0_D19
RSVD1
GND2
GND3
PPI0_D21
SPORT_INT
GND8
UART0_TX
GND4
WAKE*
GND13
EXT_BOOT
SLEEP*
RSVD11 RSVD12
RSVD10
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI0_MISO
SPI0_SEL_A
SPORT0_CLK
SPORT0_FS
SPORT1_D0
GND18
PPI0_FS2
RSVD15
PPI0_INT
PPI0_D4
PPI0_D6
PPI0_D10
GND21
PPI0_D16
PPI0_D20
GND22
GND23
RSVD17
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI0_CLK
SPI0_MOSI
GND17
SPORT0_D0
SPORT1_FS
SPORT1_CLK
PPI0_CLK
RSVD14
GND19
PPI0_D2
GND20
PPI0_D8
PPI0_D12
PPI0_D15
PPI0_D18
PPI0_D22
VIO
GND24
PS_IN
RSVD13
CLKOUT
RSVD16
PPI0_D0
Expansion Interface, Page 1
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.013
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
R232
040210K
U51
SC70_5PI3A125
2 4
1OE
BA
U36
SC70_5PI3A125
2 4
1OE
BA
U56
SC70_5PI3A125
2 4
1OE
BA
R118 10K0402
R233
040210K
U57
SC70_5PI3A125
2 4
1OE
BA
R234
040210K
R235
040210K
U58
SC70_5PI3A125
2 4
1OE
BA
3.3V
3.3V
C96
04020.01UF
C97
04020.01UF
C98
04020.01UF
C198
04020.01UF
C199
04020.01UF
R231
040210K
PE08/PWM0_SYNC/PPI0_FS1/LP2_ACK/ACM0_T0
PF07/PWM0_DH/PPI0_D07/LP2_D7
PF05/PWM0_CH/PPI0_D05/LP2_D5
PF03/PWM0_BH/PPI0_D03/LP2_D3
PF01/PWM0_AH/PPI0_D01/LP2_D1
PB05/SMC0_AMS3/SMC0_ABE1/SPT0_ACLK
PB09/SMC0_BGH/SPT0_AD0/TM0_ACLK2
PB04/SMC0_AMS2/SMC0_ABE0/SPT0_AFS
PB12/SMC0_BG/SPT0_BTDV/SPT0_AD1/TM0_ACLK1
PB12/SMC0_BG/SPT0_BTDV/SPT0_AD1/TM0_ACLK1
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
PD04/SPI0_CLK
PD00/SPI0_D2/PPI1_D16/SPI0_SEL3
PD01/SPI0_D3/PPI1_D17/SPI0_SEL2
PC12/SPI0_SEL7/PPI1_D12
PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PF08/SPI1_SEL5/PPI0_D08/LP3_D0 PF09/SPI1_SEL6/PPI0_D09/LP3_D1
PD4_SPI0CK_EI3
PD4_SPI0CK_EI3
PD3_SPI0MOSI_EI3PD3_SPI0MOSI_EI3
PD2_SPI0MISO_EI3
PD2_SPI0MISO_EI3
PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3
PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3
PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3
PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3
PD4_SPI0CK_EI3_EN
PD2_SPI0MISO_EI3_EN
PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3_EN
PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3_EN
PD3_SPI0MOSI_EI3_EN
PC15/SPI0_SEL4/PPI1_D15
PD02/SPI0_MISO
PD03/SPI0_MOSI
PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3
PD11/SPI0_SEL1/SPI0_SS
PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PB08/SMC0_A23/PPI2_D17/SPT0_BCLK
PB07/SMC0_A22/PPI2_D16/SPT0_BFS
PB06/SMC0_A21/SPT0_ATDV/TM0_ACLK4
PD15/SPI1_SEL2/PPI0_D21/SPT1_AD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE05/PPI0_D23/SPT1_AFS
PE06/SPT1_ATDV/PPI0_FS3/LP3_CLKPE07/SPT1_BTDV/PPI0_FS2/LP3_ACK
PE09/PPI0_CLK/LP2_CLK/PWM0_TRIP0
PF00/PWM0_AL/PPI0_D00/LP2_D0
PF02/PWM0_BL/PPI0_D02/LP2_D2
PF04/PWM0_CL/PPI0_D04/LP2_D4
PF06/PWM0_DL/PPI0_D06/LP2_D6
PF10/ACM0_A4/PPI0_D10/LP3_D2 PF11/PPI0_D11/LP3_D3/PWM0_TRIP1
PF12/ACM0_A2/PPI0_D12/LP3_D4 PF13/ACM0_A3/PPI0_D13/LP3_D5
PF14/ACM0_A0/PPI0_D14/LP3_D6 PF15/ACM0_A1/PPI0_D15/LP3_D7
PG13/UART1_CTS/TM0_CLK
PG14/UART1_RX/SYS_IDLE1/TM0_ACI1
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
SYS_CLKOUT
SYS_HWRST SYS_NMI/SYS_RESETOUT
SYS_EXTWAKE
TWI0_SCL TWI1_SCL
TWI0_SDA TWI1_SDA
PG02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
1A
HIROSE_FX8-120P-SV1(91)
P1C
97
95
99
96
94
101
119
71
70
120
118
116
110
108
106
104
102
98
112
100
92
90
88
86
84
82
80
78
7674
72
117
115109
107
105
103
114
113
111
93
91
89
87
85
83
81
79
77
75
73
69
66
68
67
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
5351
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37
38ASYNC_A14
ASYNC_A13
ASYNC_A8
ASYNC_A6
ASYNC_A5
ASYNC_BGH
GND6
ASYNC_ARDY
ASYNC_D19
GND5
ASYNC_D25
ASYNC_D29
ASYNC_A9
ASYNC_A7
GND7
ASYNC_A4
ASYNC_BG
ASYNC_D27
ASYNC_BR
ASYNC_D17
ASYNC_D21
ASYNC_D23
ASYNC_A10 ASYNC_A11
PWM0_TRIP0
GND12
ASYNC_A17
ASYNC_A19
GND10
PWM0_AL
GND9
PWM0_BL
GND11
PWM0_DH
PWM0_SYNC
ASYNC_A15
ASYNC_A16
ASYNC_A18
ASYNC_A20
PWM0_AH
PWM0_BH
PWM0_CH PWM0_CL
PWM0_DL
RSVD2
PWM0_TRIP1
ASYNC_AMS3
ASYNC_D30
VIN
GND1
USB_VCC
ASYNC_AOE
ASYNC_AMS2
RSVD1
GND2
GND3
ASYNC_AMS0
ASYNC_A12
GND8
RSVD4
GND4
ACM0_A1
GND13
RSVD3
ACM0_A0
ACM0_A3
ACM0_A4
ACM0_A2
GND14
ACM0_CLK
GND15
RSVD7
RSVD9
GND16
RSVD12
RSVD14
RSVD15
RSVD17
RSVD19
GND18
RSVD22
RSVD24
RSVD25
ASYNC_D20
ASYNC_D22
ASYNC_D26
GND21 GND22
GND23
ACM0_T1
RSVD5 RSVD6
RSVD8
RSVD10
RSVD11
RSVD13
GND17
RSVD16
RSVD18
RSVD20
RSVD21
RSVD23
GND19
ASYNC_D18
GND20
ASYNC_D24
ASYNC_D28
ASYNC_D31
VIO
GND24
PS_IN
ACM0_FS
ACM0_T0
RSVD26
ASYNC_D16
ASYNC_A21
ASYNC_A23
ASYNC_A25
ASYNC_A22
ASYNC_A24
3.3V
HIROSE_FX8-120P-SV1(91)
P1B
101
100
71
70
120
118
116
114
112
110
108
106
104
102
98
96
94
92
90
88
86
84
82
80
78
76
74
72
119
117
115
113
111
109
107
105
103
99
97
95
93
91
89
87
85
83
81
79
77
75
73
69
66
68
67
64
61
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
55
53
51
49
47
45
43
41
39
56
54
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37 38SPI1_SEL_CSPI1_SEL_B
SPORT3_D1
SPORT2_TDV
RSVD7
ASYNC_A1
GND6
ASYNC_RD
ASYNC_D3
GND5
ASYNC_D9
ASYNC_D13
SPORT2_D1
SPORT3_TDV
GND7
RSVD6
ASYNC_A3
ASYNC_D11
ASYNC_AMS1
ASYNC_D1
ASYNC_D5
ASYNC_D7
SPI1_D2 SPI1_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI1_RDY
GND11
RSVD10
TWI0_A0*
SPI1_SEL1/SPI1_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RSVD8
RSVD9
RSVD11
RESET_IN*
UART1_RX
RSVD5
ASYNC_D14
VIN
GND1
USB_VCC
RSVD2
RSVD4
RSVD1
GND2
GND3
RSVD3
SPORT_INT
GND8
UART1_TX
GND4
WAKE*
GND13
RSVD12
SLEEP*
RSVD14
RSVD15
RSVD13
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI1_MISO
SPI1_SEL_A
SPORT2_CLK
SPORT2_FS
SPORT3_D0
GND18
RSVD18
ASYNC_A2
ASYNC_INT
ASYNC_D4
ASYNC_D6
ASYNC_D10
GND21
RSVD19
RSVD21
GND22
GND23
RSVD23
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI1_CLK
SPI1_MOSI
GND17
SPORT2_D0
SPORT3_FS
SPORT3_CLK
RSVD17
ASYNC_A0
GND19
ASYNC_D2
GND20
ASYNC_D8
ASYNC_D12
ASYNC_D15
RSVD20
RSVD22
VIO
GND24
PS_IN
RSVD16
CLKOUT
ASYNC_WR
ASYNC_D0
3.3V
5V
3.3V
R215 00603
DNP
C1944.7UF0603
C1954.7UF0603DNP
C1964.7UF0603DNP
C1974.7UF0603DNP
R216 00603
R214 00603
R217 00603
Expansion Interface, Page 2
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.014
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
5V
R119 10K0402
PE08/PWM0_SYNC/PPI0_FS1/LP2_ACK/ACM0_T0
PE08/PWM0_SYNC/PPI0_FS1/LP2_ACK/ACM0_T0
PG05/ETH1_TXEN/RSI0_CMD/PWM1_SYNC/ACM0_T1
PF07/PWM0_DH/PPI0_D07/LP2_D7
PF05/PWM0_CH/PPI0_D05/LP2_D5
PF03/PWM0_BH/PPI0_D03/LP2_D3
PF01/PWM0_AH/PPI0_D01/LP2_D1
SMC0_AMS0
PB05/SMC0_AMS3/SMC0_ABE1/SPT0_ACLK
PB09/SMC0_BGH/SPT0_AD0/TM0_ACLK2
PB04/SMC0_AMS2/SMC0_ABE0/SPT0_AFS
PB12/SMC0_BG/SPT0_BTDV/SPT0_AD1/TM0_ACLK1
PC14/SPI1_SEL7/PPI1_D14
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
SMC0_ARE
SMC0_D3
SMC0_D9
SMC0_D13
SMC0_D11
SMC0_D1
SMC0_D5
SMC0_D7
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
SMC0_D14
SMC0_A2
SMC0_D4
SMC0_D6
SMC0_D10
SMC0_D2
SMC0_D8
SMC0_D12
SMC0_D15
SMC0_AWE
SMC0_D0
SMC0_A1
PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PWM0AH
PWM0AH
PWM0DH
PWM0DH
PWM0CH
PWM0CH
PWM0BH
PWM0BH
PD05/SPI1_CLK/TM0_ACLK7
PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PD13/SPI1_MOSI/TM0_ACLK5PD14/SPI1_MISO/TM0_ACLK6
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3PB10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PB08/SMC0_A23/PPI2_D17/SPT0_BCLKPB07/SMC0_A22/PPI2_D16/SPT0_BFS
PB06/SMC0_A21/SPT0_ATDV/TM0_ACLK4
PD15/SPI1_SEL2/PPI0_D21/SPT1_AD0 PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE03/PPI0_D16/ACM0_FS/SPT1_BFSPE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE05/PPI0_D23/SPT1_AFS
PE06/SPT1_ATDV/PPI0_FS3/LP3_CLK PE07/SPT1_BTDV/PPI0_FS2/LP3_ACK
PE09/PPI0_CLK/LP2_CLK/PWM0_TRIP0
PF00/PWM0_AL/PPI0_D00/LP2_D0
PF02/PWM0_BL/PPI0_D02/LP2_D2
PF04/PWM0_CL/PPI0_D04/LP2_D4
PF06/PWM0_DL/PPI0_D06/LP2_D6
PF10/ACM0_A4/PPI0_D10/LP3_D2
PF11/PPI0_D11/LP3_D3/PWM0_TRIP1
PF12/ACM0_A2/PPI0_D12/LP3_D4 PF13/ACM0_A3/PPI0_D13/LP3_D5
PF14/ACM0_A0/PPI0_D14/LP3_D6 PF15/ACM0_A1/PPI0_D15/LP3_D7
SMC0_ARDY/SMC0_NORWT
SMC0_BR
PG13/UART1_CTS/TM0_CLK
PG14/UART1_RX/SYS_IDLE1/TM0_ACI1
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
SMC0_AOE/SMC0_NORDV
SYS_CLKOUT
SYS_HWRST SYS_NMI/SYS_RESETOUT
SYS_EXTWAKE
TWI0_SCL TWI1_SCL
TWI0_SDA TWI1_SDA
PA00/SMC0_A03/PPI2_D00 PA01/SMC0_A04/PPI2_D01 PA02/SMC0_A05/PPI2_D02
PA03/SMC0_A06/PPI2_D03 PA04/SMC0_A07/PPI2_D04
PA05/SMC0_A08/PPI2_D05 PA06/SMC0_A09/PPI2_D06
PA07/SMC0_A10/PPI2_D07
PB01/SMC0_AMS1/PPI2_FS1
PA08/SMC0_A11/PPI2_D08
PA09/SMC0_A12/PPI2_D09
PA10/SMC0_A14/PPI2_D10 PA11/SMC0_A15/PPI2_D11
PA12/SMC0_A17/PPI2_D12
PA13/SMC0_A18/PPI2_D13 PA14/SMC0_A19/PPI2_D14
PA15/SMC0_A20/PPI2_D15
PB02/SMC0_A13/PPI2_FS2
PB03/SMC0_A16/PPI2_FS3
PG02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
1B1C
112
110
108
106
104
102
98
96
94
92
90
88
86
84
82
80
78
76
74
72
119
117
115
113
111
109
107
105
103
99
97
95
93
91
89
87
85
83
81
79
77
75
73
69
66
6867
64
63
65
11
62
36
35
8
6
4
2
9
7
5
3
1
12
10
59
60
61
53
51
49
47
45
43
41
39
56
52
50
40
48
46
44
42
58
57
3433
16
18
20
22
14
24
26
28
30
32
13
15
17
19
21
23
25
27
29
31
37 38
P2A
HIROSE_FX8-120P-SV1(91)
55
54
101
100
71
70
120
118
116
114
SPI2_SEL_CSPI2_SEL_B
SPORT3_D1
SPORT2_TDV
PPI_FS1
RSVD5
GND6
RSVD2
PPI1_D3
GND5
PPI1_D9
PPI1_D13
SPORT2_D1
SPORT3_TDV
GND7
PPI1_FS3
RSVD4
PPI1_D11
RSVD3
PPI1_D1
PPI1_D5
PPI1_D7
SPI2_D2 SPI2_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI2_RDY
GND11
RSVD8
SPI2_SEL1/SPI2_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RSVD6
RSVD7
RSVD9
RESET_IN*
UART2_RX
PPI1_D17
PPI1_D14
VIN
GND1
USB_VCC
PPI1_D23
PPI1_D19
RSVD1
GND2
GND3
PPI1_D21
SPORT_INT
GND8
UART2_TX
GND4
WAKE*
GND13
SLEEP*
RSVD13 RSVD14
RSVD12
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI2_MISO
SPI2_SEL_A
SPORT2_CLK
SPORT2_FS
SPORT3_D0
GND18
PPI1_FS2
RSVD17
PPI1_INT
PPI1_D4
PPI1_D6
PPI1_D10
GND21
PPI1_D16
PPI1_D20
GND22
GND23
RSVD19
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI2_CLK
SPI2_MOSI
GND17
SPORT2_D0
SPORT3_FS
SPORT3_CLK
PPI1_CLK
RSVD16
GND19
PPI1_D2
GND20
PPI1_D8
PPI1_D12
PPI1_D15
PPI1_D18
PPI1_D22
VIO
GND24
PS_IN
RSVD15
CLKOUT
RSVD18
PPI1_D0
RSVD10
RSVD11
5V5V
3.3V
P3A
HIROSE_FX8-120P-SV1(91)
55
54
100
70 96
119
97
66
6867
2
61
53
51
56
22 24
21
25
101
71
120
118
116
114
112
110
108
106
104
102
98
94
92
90
88
86
84
82
80
78
76
74
72
117
115
113
111
109
107
105
103
99
95
93
91
89
87
85
83
81
79
77
75
73
69
64
63
65
11
62
36
35
8
6
4
9
7
5
3
1
12
10
59
60
49
47
45
43
41
39
52
50
40
48
46
44
42
58
57
3433
16
18
20
14
26
28
30
32
13
15
17
19
23
27
29
31
37 38SPI3_SEL_CSPI3_SEL_B
SPORT5_D1
SPORT4_TDV
PPI_FS1
GND6
PPI2_D3
GND5
PPI2_D9
PPI2_D13
SPORT4_D1
SPORT5_TDV
GND7
PPI2_FS3
PPI2_D11
PPI2_D1
PPI2_D5
PPI2_D7
SPI3_D2 SPI3_D3
RESET_OUT*
GND12
SCL1*
GPIO2
GND10
TMR_A
GND9
SPI3_RDY
GND11
SPI3_SEL1/SPI3_SS*
SDA1*
GPIO0
GPIO4
GPIO6
TMR_C
RESET_IN*
UART3_RX
PPI2_D17
PPI2_D14
VIN
GND1
USB_VCC
PPI2_D23
PPI2_D19
GND2
GND3
PPI2_D21
SPORT_INT
GND8
UART3_TX
GND4
WAKE*
GND13
SLEEP*
GND14
TMR_B
GND15
GPIO3
SCL0*
GND16
SPI3_MISO
SPI3_SEL_A
SPORT4_CLK
SPORT4_FS
SPORT5_D0
GND18
PPI2_FS2
PPI2_INT
PPI2_D4
PPI2_D6
PPI2_D10
GND21
PPI2_D16
PPI2_D20
GND22
GND23
TMR_D*
GPIO7*
GPIO5
GPIO1
SDA0*
SPI3_CLK
SPI3_MOSI
GND17
SPORT4_D0
SPORT5_FS
SPORT5_CLK
PPI2_CLK
GND19
PPI2_D2
GND20
PPI2_D8
PPI2_D12
PPI2_D15
PPI2_D18
PPI2_D22
VIO
GND24
PS_IN
CLKOUT
PPI2_D0
RSVD5
RSVD2
RSVD4RSVD3
RSVD8
RSVD6
RSVD7
RSVD9
RSVD1
RSVD13 RSVD14
RSVD12
RSVD17
RSVD19
RSVD16RSVD15
RSVD18
RSVD10
RSVD11
3.3V
Expansion Interface, Page 3
1/5/12 16
A0269-2011
ADSP-BF609 EZ-Board
1.015
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
PC14/SPI1_SEL7/PPI1_D14
PC14/SPI1_SEL7/PPI1_D14
PE00/SPI1_D3/PPI0_D18/SPT1_BD1 PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE00/SPI1_D3/PPI0_D18/SPT1_BD1
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0 PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
PG01/SPT2_AFS/TM0_TMR2/CAN0_TX
PC12/SPI0_SEL7/PPI1_D12
PC12/SPI0_SEL7/PPI1_D12
PD07/UART0_TX/TM0_ACI3
PD06/ETH0_PHYINT/PPI1_FS2/TM0_ACI5
PC02/ETH0_TXD0/PPI1_D02
PC04/ETH0_RXERR/PPI1_D04
PC06/ETH0_MDC/PPI1_D06
PB15/ETH0_PTPPPS/PPI1_FS3
PC01/ETH0_RXD1/PPI1_D01
PC03/ETH0_TXD1/PPI1_D03
PC05/ETH0_CRS/PPI1_D05
PC07/ETH0_MDIO/PPI1_D07
PB14/ETH0_REFCLK/PPI1_CLK PB13/ETH0_TXEN/PPI1_FS1/TM0_ACI6
PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1 PG08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PD4_SPI0CK_EI3
PD3_SPI0MOSI_EI3PD2_SPI0MISO_EI3
PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3
PD0_SPI0D2_EPPI1D16_SPI0SEL3_EI3
PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3
PD1_SPI0D3_EPPI1D17_SPI0SEL2_EI3
PC00/ETH0_RXD0/PPI1_D00
PC08/PPI1_D08 PC09/ETH1_PTPPPS/PPI1_D09
PC10/PPI1_D10 PC11/PPI1_D11/ETH_PTPAUXIN
PC13/SPI0_SEL6/PPI1_D13/ETH_PTPCLKIN
PC15/SPI0_SEL4/PPI1_D15
PC15/SPI0_SEL4/PPI1_D15
PD05/SPI1_CLK/TM0_ACLK7
PD08/UART0_RX/TM0_ACI0
PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4 PD09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3
PD10/SPI0_RDY/UART0_CTS/SPI1_SEL3
PD11/SPI0_SEL1/SPI0_SS
PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PD12/SPI1_SEL1/PPI0_D20/SPT1_AD1/SPI1_SS
PD13/SPI1_MOSI/TM0_ACLK5PD14/SPI1_MISO/TM0_ACLK6
PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3 PB11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB08/SMC0_A23/PPI2_D17/SPT0_BCLKPB07/SMC0_A22/PPI2_D16/SPT0_BFS
PD15/SPI1_SEL2/PPI0_D21/SPT1_AD0 PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE01/SPI1_D2/PPI0_D19/SPT1_BD0 PE01/SPI1_D2/PPI0_D19/SPT1_BD0
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE02/SPI1_RDY/PPI0_D22/SPT1_ACLK
PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE03/PPI0_D16/ACM0_FS/SPT1_BFS PE03/PPI0_D16/ACM0_FS/SPT1_BFS
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK PE04/PPI0_D17/ACM0_CLK/SPT1_BCLK
PE05/PPI0_D23/SPT1_AFS
PE06/SPT1_ATDV/PPI0_FS3/LP3_CLK PE07/SPT1_BTDV/PPI0_FS2/LP3_ACK
PG07/SPT2_BFS/TM0_TMR5/CNT0_ZM
PG09/SPT2_AD0/TM0_TMR4
PG10/UART1_RTS/SPT2_BCLK
PG11/SPT2_BD1/TM0_TMR6/CNT0_UD
PG12/SPT2_BD0/TM0_TMR7/CNT0_DG
PG13/UART1_CTS/TM0_CLK PG13/UART1_CTS/TM0_CLK
PG14/UART1_RX/SYS_IDLE1/TM0_ACI1 PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4 PG15/UART1_TX/SYS_IDLE0/SYS_SLEEP/TM0_ACI4
SYS_CLKOUT SYS_CLKOUT
SYS_HWRST SYS_HWRSTSYS_NMI/SYS_RESETOUT SYS_NMI/SYS_RESETOUT
SYS_EXTWAKE SYS_EXTWAKE
TWI0_SCL TWI0_SCLTWI1_SCL TWI1_SCL
TWI0_SDA TWI0_SDATWI1_SDA TWI1_SDA
PA00/SMC0_A03/PPI2_D00 PA01/SMC0_A04/PPI2_D01
PA02/SMC0_A05/PPI2_D02 PA03/SMC0_A06/PPI2_D03
PA04/SMC0_A07/PPI2_D04 PA05/SMC0_A08/PPI2_D05
PA06/SMC0_A09/PPI2_D06 PA07/SMC0_A10/PPI2_D07
PB00/SMC0_NORCLK/PPI2_CLK PB01/SMC0_AMS1/PPI2_FS1
PA08/SMC0_A11/PPI2_D08 PA09/SMC0_A12/PPI2_D09
PA10/SMC0_A14/PPI2_D10 PA11/SMC0_A15/PPI2_D11
PA12/SMC0_A17/PPI2_D12 PA13/SMC0_A18/PPI2_D13
PA14/SMC0_A19/PPI2_D14 PA15/SMC0_A20/PPI2_D15
PB02/SMC0_A13/PPI2_FS2 PB03/SMC0_A16/PPI2_FS3
PG02/ETH1_TXD1/PWM1_AL/RSI0_D1 PG02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG06/ETH1_REFCLK/RSI0_CLK/SPT2_BTDV/PWM1_TRIP0
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
PG04/SPT2_ACLK/TM0_TMR1/CAN0_RX/TM0_ACI2
2A 3A
C851000PF1206
TP25
MH20.144
3.3V
R1260.051206
R1250.051206
C904.7UF0805
PGND
4A
W2COPPER
DEFAULT=INSTALLED
SJ4
JUMPERSHORTING
MH30.144
MH40.144
MH50.144
MH60.144
5V 3.3V
5V
R1210.051206
FER26001206
C8610UF1210
FER36001206
0603
R13224.9K
PGND
R12000402D2
GSOT05
SOT23-3
C881UF0805
CT1150UFD
C891000PF1206
C871UF0805
U50
MIC2025-1SOIC8
1
3
8
67
2FLG
IN1 OUT1
OUT2
GND
EN
FER4190FER002
2
3
1
4
D5MBRS540T3G
SMC
R130255.0K0603
5V
PGND
PGND
CT3220UFD2E
VR1
ADP1864AUJZSOT23-6
2
1
3 6
4
5IN
CS
PGATEFB
COMP
GNDR13180.6K0603 D6
MBRS540T3G
SMC
R1270.0361206
L12.5UHIND013
TP12 TP13 TP14 TP15 TP16 TP17 TP18 TP19 TP20
TP7
C2000.1UF0402
080510UF
DNP
C102
C9168PF0603
R236
04020
DNP
C92470PF0603
C10310UF1210
P11
IDC2X1
1 2
F13AFUS004
SHGND
SHGND
PGND
R12900603
R1280.0361206
TP21
MH90.144
MH80.144
MH70.144
GP1LOOP_2838
VR2
ADP2119ACPZ-R7DFN50P300X300-11N
7
11
6
8
10
5
2
9
4
3
1VIN
SW
PGND
SYNC/MODE
PVIN
GND
EN
PGOOD
FB
EPAD
TRK
ADSP-BF609 EZ-Board
161/5/12
Power
16
A0269-2011 1.0
D
4
3
2
1
A B C
20 Cotton Road
Nashua, NH 03063
A B C D
4
3
2
1
PH: 1-800-ANALOGD
C
Title
Size Board No.
Date Sheet of
DEVICESANALOG
Rev
VR3
ADP1715MSOP8
4
2
5
31
6 7 8 GN
D4
GN
D3
GN
D2
EN OUT
GN
D1
IN
SS
DNP
R12210K0402P10
IDC2X1
1 2
TP5
R12310K0402DNP
R1240.051206
DNP
CT22.2UFB
C1012.2UF0805
R1450.051206
TP26
D8SK12
DO-214AA
D1ESD5Z2.5T1
SOD-523
DEFAULT=INSTALLED
SJ2
JUMPERSHORTING
DEFAULT=INSTALLED
SJ3
JUMPERSHORTING
R237
060310
DEFAULT=INSTALLLED
SJ1
JUMPERSHORTING
R23800402
C992.2UF0805
P15
IDC2X1
1 2
TP8
D4GSOT03
SOT23-3
L2
IND0031.5UH
MH10.144
R23910K0402
R24230K0402
R24000402
TP27
R24100402DNP
C201
121022UF
R24332.4K0402
5V
C202
121022UF
C203
121022UF
TP23
TP24
DEFAULT=INSTALLED
SJ6
JUMPERSHORTING
DEFAULT=INSTALLED
SJ5
JUMPERSHORTING
P12
IDC2X1
1 2
D3GSOT03
SOT23-3
C950.1UF0402
P13
IDC2X1
1 2U6
SI7403BDNICS010
TP22
PWR
P18
CON045
2
3
1
POWER
P14
IDC2X1
1 2
TP6
3.3V
5V
R1440.051206
D7MBRS540T3G
SMC
C1000.1UF0402
USB_VBUS
VDD_DMC
VDD_INT
VDD_EXT
USB_VBUS_EN
USB_VBUS_EN
VDD_USB
USB0_VBC
SYS_EXTWAKE
Remove P13 when measuring 3.3V
"VDD_DMC"
1.8V @ 500mA
"3.3V"
Remove P10 when measuring USB_VBUS
3.3V @ 2A
LABEL "GND" ON ALL TPs
"5V"
GND Test Points are scattered on PCB for Test Measurement Purposes.
"VDD_INT"
Remove P11 when measuring VDD_USB
Remove P12 when measuring VDD_EXT
Remove P15 when measuring VDD_DMC
Remove P17 when measuring VDD_INT1.25V @ 1.5A
"VDD_EXT"
"VDD_USB"
"USB_VBUS"