adjustments sam via minidialog

8/11/2019 Adjustments Sam via Minidialog

http://slidepdf.com/reader/full/adjustments-sam-via-minidialog 1/4

Adjustments SAM via MINIDIALOG40012_A3

- 1 -

File Release Last Save Date of Creation Status Author FB_SAM_MiniDialog_MOTIVLINE_r02-v00_08-03-25.doc 02-002008-03-25 2008-03-25 released Schmauder, MAA-I

Hardware:SAM - PN: X00E5 0200008Software-Version: 40012_A3

Adjustments SAM via MINIDIALOG

1 Configuration node-nr. & Baudrate (only necessary if “SAM.dat” isnot available on CF-card)

Prerequisites: Power supply switched Off

Push and simultanously and switch on the Power Supply

Use or to scroll through the menu

2 Download with programmed CF-card

2.1 Cleanup SAM-card (Not necessary if SAM is new -> no software to be erased)

Select with or

Possible Choices:

- NO- NOW

Confirm with

This function erases all data on SAM (similar to format C:\)

Caution: After cleanup is complete, the SAM has to be reset in order for the DiaSys - parameters in the CF card totake effect.

2.2 Downlad Software

- Download procedure is starting automatically after cleanup or shuton wait about 3 mins.

Confirm with

now the A - parameters from the Flash card will be programmed into the SAM-Flash

ENTERCleanup? NOWPrev Next

Cleanup? NOPrev Next

Reconf. A-Param?NO YES

ENTER

ESC ENTER




- 2 -


- A - Params = Anlagen - (Plant-) Parameters like Node-Nr. and Baudrate of SAM

Confirm with

now the D - parameters from the Flash card will be taken into the SAM-Flash

- D-Params = DiaSys Parameters

- SAM starts operation with default page = Alarm page

3 Configuration of J1939 or CAN - Open:

Prerequisites: Power Supply on, SAM operating in Alarm Page

Push and simultaneously for approx. 5secs

The menue tree shows up

Confirm with

3.1 Password Options:

3.1.1 Option 1: ADEC is connected, CAN communication is operational.

- Password is Engine Operating hours converted into HEX - adecimal format

- Read-out Engine operating hours in SAM-module:

- Return to previous menu with


Confirm with

- First measuring point in this menue is Operating Hours:

PV001115 ECU Operating hoursX.XX h

Select : Act, value page

ENTER

Select :Password page

ENTER

ESC

ESC ENTER

Reconf. D-Param?NO YES

ENTER




- 3 -


- Return to previous menu with

- Return to Password Page

- Convert Operating hours into HEX - format and enter into password

3.1.2 Option 2: ADEC is not connected, no CAN communication:

Enter the password as: A-C-D-C

3.2 Enter the Parameter Page - menue:

After the password has been entered, the following menue pops up:

Confirm with

3.2.1 Select your engine:

• 12 V 4000 C 13• 12 V 4000 C 23• 16 V 4000 C 13• 16 V 4000 C 23• 20 V 4000 C 13• 20 V 4000 C 23

3.2.2 Select Display Start Page

Aux PageECU OverviewECU PressureECU Temp

3.2.3 Select the used interface:

Select with or

Possible Choices:

- No- SAE J1939- CAN Open

Interface Config No

Select :Parameter page

ENTER

ESC




- 4 -


3.2.4 Save Changes

Confirm with

The following Menue item pops up:


Until the menue

Pops up and confirm withENTERSelect:

Alarm Page

Select:Parameter Page

ENTERSave Changes?Exit Yes

adjustments sam via minidialog

Documents