L U M I N A I R E S P E C I F I C A T I O N

Specifications and dimensions subject to change without notice. Specification sheets that appear on pinnacle-ltg.com are the most recent version and supersede all other previously printed or electronic versions.

®

T8Architectural Recessed Luminaire

Project Name

TypeCatalog Number

Date

Satine Lens (A) Baffle (B) Linear Slot (L) Round Perf (R)

CONSTRUCTION Formed 20 gauge cold rolled steel housing. Highly reflective die-formed white painted reflector. Wiring access available on top of housing.

FINISH Powder-coat white painted finish on exposed trim.

LABELS UL and cUL Listed, approved for dry/damp location unless otherwise noted.

ELECTRICAL Instant start 120/277V electronic ballast with less than 10% THD. Standard single circuit. Each ballast provided with disconnects to meet luminaire disconnect code requirement.

MOUNTING Designed to install into acoustical grid and inaccessible ceilings. Specify G1, G9 or GS for acoustical grid ceiling. Specify FL or S for inaccessible ceilings. Grid retention clips integral to housing. Consult factory for detailed installation instructions.

OPTICS Captive and hinged center satine curved, co-extruded acrylic lens with ribbed side channels evenly illuminates the side reflector giving the appearance of a fully lensed luminaire.

Baffle with Satine Lens (BF)

__- ___- W- ___

Matte White

W-120-277-347-UNV-

120 V277 V347 V1

UNV (120/277)2

__-MOUNTING VOLTAGE CIRCUITING FINISH OPTIONSHOUSING LAMPS

___-

Through-Wired5

Step Switching7

Daylight Sensor Master - Sensor Included6,7

Daylight Sensor Satellite - Sensor Not Included6,7

Internal Fast-Blow FuseAir ReturnChicago Plenum6’, 18-gauge, Flex Whip12’, 18-gauge, Flex WhipAntimicrobial Paint

TW- SW-DSM-

DSS-

GLR-AR-CP-FW6-FW12-AM-

AD24__-

AD24A- Adeo 2X4 Recessed with Satine Lens

Sample Catalog #: AD24A-2T8-G1-120-1C-W

G1-G9-GS-

1” Ceiling Grid9/16” Ceiling GridScrew Slot Ceiling Grid

Acoustical Grid Ceiling Single Circuit, Normal Dual Circuit, Normal3

Single Circuit Dimming7

Dual Circuit Dimming3,7

Single Circuit with Emergency Circuit4,7

Single Circuit with a Battery Pack4,7

Dual Circuit with a Battery Pack3,4,7

1C-2C-1D-2D-1E-

1B-

2B-

1T8-2T8-3T8-

(1) 32W T8 (2) 32W T8 (3) 32W T8

1Consult factory for 347 volt ballast. 2Not available for use with a battery pack. 3Dual circuit available for 2 (side-by-side) and 3 (inboard/outboard) lamp configurations. 4Emergency circuit or battery pack to be on center lamp with 3 lamp configurations. 5Individual fixtures are through-wired for continuous pattern. Fixtures cannot be joined. 6See back page for ordering information. Requires 0-10 volt dimming. 7Some Adeo configurations will not accommodate all options. Consult factory.

AD24L- Adeo 2X4 Recessed with Linear SlotAD24B- Adeo 2X4 Recessed with internal Baffle

AD24R- Adeo 2X4 Recessed with Round Perf

Inaccessible CeilingFL-

S-

Standard Flange(Separate Flange Kit)Surface Mount(See surface mount specification sheet for dimensions)

AD24BF- Adeo 2X4 Recessed Satine Lens with internal Baffle

Pinnacle Architectural Lighting 12655 East 42nd Avenue, Suite 50 Denver, CO 80239 Phone 303.322.5570 Fax 303.322.5568 www.pinnacle-ltg.com© 2017 Pinnacle Architectural Lighting® January 2017

ADEO2X4

YEARWARRANTY

ConvertibleLED

ConvertibleLFL

LFL LED

YEARWARRANTY

ConvertibleLED

ConvertibleLFL

LFL LED

YEARWARRANTY

ConvertibleLED

ConvertibleLFL

LFL LED

24"

4-3/8”

1, 2 Biax 1, 2, 3 T8

LAMP OPTIONS

LAMP OPTIONS

2 T81 T8

LAMP OPTIONS

Adeo 2x2 (AD22)

Adeo 2x4 (AD24)

Adeo 1x4 (AD14)

Side View

4-3/8”

24"

Side View

2”

24"

4-3/8” 4-3/8”

48"

Side View

2”

4-3/8”

48"

2”

12"

4-3/8”

1 T8 2 T8 3 T8

24"

4-3/8”

1, 2 Biax 1, 2, 3 T8

LAMP OPTIONS

LAMP OPTIONS

2 T81 T8

LAMP OPTIONS

Adeo 2x2 (AD22)

Adeo 2x4 (AD24)

Adeo 1x4 (AD14)

Side View

4-3/8”

24"

Side View

2”

24"

4-3/8” 4-3/8”

48"

Side View

2”

4-3/8”

48"

2”

12"

4-3/8”

1 T8 2 T8 3 T8

Specifications and dimensions subject to change without notice. Specification sheets that appear on pinnacle-ltg.com are the most recent version and supersede all other previously printed or electronic versions.

P H O T O M E T R I C S A D E O 2 x 4 ( T 8 )

G1 (1”Ceiling Grid) Mounting Options G9 (9/16”Ceiling Grid) Mounting Options GS (Screw Slot Grid) Mounting Options

1” Ceiling Grid with Standard Tile

1” Ceiling Grid with Tegular Tile

9/16” Ceiling Grid with Standard Tile

9/16” Ceiling Grid with Tegular Tile

Screw Slot Ceiling Grid 9/16” Ceiling Grid with Tegular Tile (fixture flush with tile)

M O U N T I N G D E T A I L

Pinnacle Architectural Lighting 12655 East 42nd Avenue, Suite 50 Denver, CO 80239 Phone 303.322.5570 Fax 303.322.5568 www.pinnacle-ltg.com© 2017 Pinnacle Architectural Lighting® January 2017

Notched endcap

Lamps

(2) #8-32 Screws

Ballast Tray

BallastCaptive Lens

AIR RETURNINTEGRAL DAYLIGHT SENSOR

ORDERING INFORMATION: Specify Air Return in the options section of the part number. (Sample Catalog #: AD24A-1T8-G1-120-1C-W-AR)

TECHNICAL: Air Return component is integral to the fixture housing. Made of 20 gauge cold rolled steel painted. Slot size is .50” x .06” and spaced .12” apart from each other.

DAYLIGHT SENSOR: Daylight sensor dims lights based on electric light and presence of daylight. Sensor can control up to 20 dimming ballasts. Sensor is factory calibrated to 45 footcandles (fc), adjustable by 1/3 to 3 times the default setting by rotating the aperture.ORDERING INFORMATION: Specify “DSM” or “DSS” in the Options section of the part number when ordering Integral Daylight Sensor. Daylight Sensor Master (DSM) includes the fixture with sensor and dimming ballast. Controls DSS units. Daylight Sensor Satellite (DSS) includes the fixture with a sensor compatible dimming ballast only. Must be used in conjunction with a DSM unit. (0-10v) dimming must be utilized. (Sample Catalog #: AD24A-1T8-G1-120-1C-W-DSM)

APPLICATION: Daylight sensor is a turn key solution for lighting control. Integral sensor is wired to the 0-10 volt dimming ballast at the factory. No additional wiring is required by the contractor.

LAMP AND BALLAST MAINTENANCEOPENING THE LENS: Locate notch on the fixture endcap. Pull down on the notched side to release the lens. Lens swings open.

ACCESSING THE LAMPS: Lamps are accessible once lens is open. Lens remains captive to fixture housing during lamp maintenance.

REMOVING BALLAST SCREWS: Remove (2) screws holding the bal-last tray. Be sure to hold tray while removing the screws.

REMOVING BALLAST TRAY: Gently pull on socket and ballast tray will release from housing. Ballast is fully accessible.

APPLICATION: Air Return is an alternative method for allowing air to access the plenum. Optional Air Return slots are located on side panels. Slots are evenly spaced for most efficient air flow into plenum with minimal distraction to fixture appearance.

®

Test #: 203623Part #: AD24A-1T8Total Luminaire Efficiency: 79.0%

719

540

360

180

Test #: 203634Part #: AD24A-2T8Total Luminaire Efficiency: 63.0%

964

643

321

1285