additional tail lamps - til.scania.com · if the led tail lamp is fitted on a tractor, an adapter...

PGRT

11:60-08/02 Issue 8.1 e

Additional tail lamps

General information on connecting additional tail lamps

More information on changing from bulb to LED lamp is found in the document, LED lamps for tractors, trucks and trailers under Electrical system.

341

740

Compact 7-chamber lamp assembly

340 9

05

LED lamp

341 7

22

7-chamber lamp

General information on connecting addi-tional tail lampsTail lampsThere are 3 types of tail lamps:

• Compact 7-chamber lamp assembly• LED lamp• 7-chamber lamp assembly

Additional tail lamps can be connected in the following two ways:

1. Connection via cable harness for twin tail lamps.2. Connection via bodywork cable harness in frame.

The cable harness in connection instructions 1 is a complete cable harness which can be connected to the vehicle’s standard connector. The cable harness and connector fit all types of lamps and are available from Scania dealers.

The compact 7-chamber lamp assembly is a shorter option, e.g. for trucks with a tail lift. It is certified in Europe for horizontal mounting.

Note:Comply with local legal requirements when fitting tail lamps on underrun protection.

All three lamps have the same hole template for fitting.

Note:If the LED tail lamp is fitted on a tractor, an adapter plate is required that moves the lamp out approx. 50 mm sideways.

n-GB 1 (10)© Scania CV AB 2015, Sweden

PGRT General information on connecting additional tail lamps


The individual chassis specification (ICS) can be ordered together with the individ-ual main dimension drawing (ICD) under Drawings (requires login).

The parts can be purchased from a Scania dealer.

Connection optionsThere are two different connection options depending on which control unit for the regulation of sight and visibility functions the vehicle is equipped with. The latest one is called CUV2 in the document and the previous one CUV1. The control unit version can be seen from the vehicle’s individual chassis specification, ICS. The con-nection alternatives do not have any clear chassis number limit, therefore variant codes are used instead.

Control unit Variant codeCUV2 3115BCUV1 3115A

© Scania CV AB 2015, Sweden

11:60-08/02 Issue 8.1 en-GB 2 (10)



Standard load, bulb

Standard load, LED

Maximum loada Fuse

Approx. 40 W 10.2 W 144 W10 As Approx. 40 W 10.2 W 144 W

4 x 21 W 2 x 3.7 W + trailer 2 x 21 W + 2 x 70 W + 10 W

CUV2b

2 x 21 W 2 x 2.8 W 4 x 21 W + 10 W6 x 21 W

1 x 21 W 2 x 9.8 W 4 x 21 W5 x 21 W

1 x 21 W 2 x 9.8 W 4 x 21 W5 x 21 W

4 x 21 W 2 x 3.7 W + trailer 8 x 21 W

More information about electrical connections can be found in the document Gener-al information about installation instructions.

Connecting (CUV2)When connecting additional tail lamps, the normal vehicle electrical system and fus-es must not be overloaded. See the table below for the maximum permitted continu-ous loads. If more power is required, a relay must be used.

Connection Standard current consumers

a. 60% of the rated current of the fuse or electronic overload protection at continuous load

Position lamp, right-hand side End-outline marker lamp for truckPosition lamp, left-hand side End-outline marker lamp and registration plate lamp

on truckReversing light Truck and trailer

b. Electronic overload protection

Brake lamp Rigid truckTrailer

Direction indicator, right-hand side

Truck, rearTrailer

Direction indicator, left-hand side

Truck, rearTrailer

Rear foglight Rear foglight on truck and trailer


11:60-08/02 Issue 8.1 en-GB 3 (10)



Standard load, bulb

Standard load, LED Maximum loada Fuse

Approx. 40 W 10.2 W 144 W

10 Amps on Approx. 40 W 10.2 W 144 W

4 x 21 W 2 x 3.7 W + trailer 6 x 21 W4 x 21 W 2 x 2.8 W + trailer 6 x 21 W3 x 21 W 2 x 9.8 W 5 x 21 W

CUV1b3 x 21 W 2 x 9.8 W 5 x 21 W2 x 21 W 2 x 3.7 W + trailer 4 x 21 W

More information about electrical connections can be found in the document Gener-al information about installation instructions.

Connecting (CUV1)When connecting additional tail lamps, the normal vehicle electrical system and fus-es must not be overloaded. See the table below for the maximum permitted continu-ous loads. If more power is required, a relay must be used.

Connection Standard current consumers

a. 60% of the rated current of the fuse or electronic overload protection at continuous load

Position lamp, right-hand side End-outline marker lamp for truckPosition lamp, left-hand side End-outline marker lamp and registration plate la

truckReversing light Truck and trailerBrake lamp Truck and trailerRH direction indicators RH direction indicators on truck

b. Electronic overload protection

LH direction indicators LH direction indicators on truckRear foglights Rear foglights on truck and trailer


11:60-08/02 Issue 8.1 en-GB 4 (10)

PGRT Chassis conditions


Alternative Variant coderom cab to frame 7-pin 2411B

7+7-pin 2411E7+7+7-pin 2411F

n frame 2 m 3023A8 m 3023D12 m 3023C

Alternative Variant coderom cab to frame 7-pin 2411B

4+7-pin 2411C4+7+7-pin 2411D7+7-pin 2411E

n frame 2 m 3023A7 m 3023B12 m 3023C

Chassis conditionsExtra tail lamps can be connected to the cable harness for tail lamps on all Scania trucks. Two cable harnesses with part number 1 858 746 are required.

If the extra tail lamps should be connected using a cable harness for bodywork, the following requirements apply:

Vehicle production period Preparations from factoryProduction site Chassis serial number Option

2005-01-21 - Bodywork cable harness fSödertälje 2 006 429 -Zwolle 5 117 958 -Angers 9 097 244 - Bodywork cable harness i

Vehicle production period Preparations from factoryProduction site Chassis serial number Option

- 2005-01-20 Bodywork cable harness fSödertälje - 2 006 428Zwolle - 5 117 957Angers - 9 097 243

Bodywork cable harness i


11:60-08/02 Issue 8.1 en-GB 5 (10)

PGRT Connection instructions


304

320

Cable with shrinking tubing

Connection instructionsAlternative 1: Connection via cable harness for twin tail lampsWork descriptionDisconnect the cable from the tail lamp and route it into the frame so that the connec-tor ends up in the beam web and then connect the cable harness for twin tail lamps.

IMPORTANT!

Do not clamp the cable to the shrinking tubing close to the connector, the grey-marked area on the cable in the illustration.


11:60-08/02 Issue 8.1 en-GB 6 (10)



304

321

Cable harness for twin tail lamps. Part number 1 858 746.

Part informationTwo cable harnesses are required, one for the right-hand side of the vehicle and one for the left-hand side.

The short part of the cable harness is 1,105 mm and the longer part is 1,355 mm.

The parts are available from Scania dealers.


11:60-08/02 Issue 8.1 en-GB 7 (10)



330

791

C487

C488

C486

348

620

Alternative 2: Connection via bodywork cable har-ness in frameWork descriptionObtain the signals for the additional tail lamps from the connector for standard func-tions, C489, and from the central electric unit. The signals are bridged to connector C494 which passes the signals on to the DIN connectors under the cab via the option bodywork cable harness from cab to frame.

The option Bodywork cable harness in frame is to be connected to the DIN connec-tors and then routed to the tail lamps.

For vehicles manufactured up to 8 March 2011, the bodywork cable harness connec-tions can be found on the upper part of the left-hand wheel housing.


11:60-08/02 Issue 8.1 en-GB 8 (10)



C494

+24 V G151

2

3

5

6

7

C489

321

57

2021

1918171615

4

C48667

54321

4

C494

815

C494

C494 C494

C489C489

359 2

22

C486

Part information and connection positions

Rear foglight is applicable from the following chassis serial numbers onwards:

1 Fuse Supplied from the factory2 Cable Cable cross-sectional area 1.5

mm² minimum 3 Cable Cable cross-section 2.5 mm² min-

imum Connected with ring cable termi-nal to G15Fitted by bodybuilder

4 Bodywork cable harness from cab to frame Pre-routed at the factory5 Bodywork cable harness in frame Cable cross-sectional area 1.5

mm² minimum Supplied from the factory, fitted by bodybuilder

6 Additional tail lamps Fitted by bodybuilder7 Bodywork cable harness in frame Cable cross-section 2.5 mm²

Supplied from the factory, fitted by bodybuilder

8 Rear foglight Output +24 V

Vehicle production periodProduction site Chassis serial number

2010-05-21 -Södertälje 2 054 445 -Zwolle 5 240 385 -Angers 9 148 934 -


11:60-08/02 Issue 8.1 en-GB 9 (10)



The parts are available from Scania dealers.

São Bernardo do Campo 3 663 314 -


11:60-08/02 Issue 8.1 en-GB 10 (10)

Additional tail lampsGeneral information on connecting additional tail lampsTail lampsConnection optionsConnecting (CUV2)Connecting (CUV1)

Chassis conditionsConnection instructionsAlternative 1: Connection via cable harness for twin tail lampsWork descriptionPart information

Alternative 2: Connection via bodywork cable harness in frameWork descriptionPart information and connection positions

additional tail lamps - til.scania.com · if the led tail lamp is fitted on a tractor, an adapter...

Documents