active bandpass filters

www.electronics-tutorials.com

LAST MODIFIED: Wednesday, 30-Nov-2005 18:46:43 PST

Active band pass Filters

YOU ARE HERE: HOME > FILTERS > ACTIVE band pass FILTERS

What are active band pass filters?

Active band pass filters are simply filters constructed by using operational amplifiers as active devices configured to simulate inductors or what are known as "gyrators". Active band pass filters are used largely at audio frequencies where otherwise the size of the inductor would become prohibitive. The are many different types of active filters including high pass, low pass, band reject and there are numerous responses including multiple feedback band pass (MFBP), dual-amplifier band pass (DABP) and, state variable bi-quad all pole circuits. Interestingly all known filter responses such as Butterworth and Chebyshev may be synthesised.

Active band pass filter schematic

Here we will only consider the time honoured multiple feedback band pass (MFBP) type which uses capacitors of equal value and leads us to simplified calculations. Let's look at the basic circuit in figure 1 below.

Figure 1 - an active band pass filter

Now the calculations are fairly simple. You need to determine several things first, Ho the gain per stage, Q the bandwidth and Wo which is 2 * pi * Fc.

Finally pick a convenient value for C which if reasonably large, leads to smaller values of resistance and consequently some aid in reducing noise.

Valuable feedback (no pun intended) from readers using rate-this-page (see below

of 4active bandpass filters

6/25/2011file://D:\CSG\datasheets\active bandpass filters.htm

and on every other page) indicates the following needs clarification:

(a) the 100 uF capacitor above is purely part of the power supply reservoir and has nothing to do with the filter itself. The two 10K resistors are part of the power supply biasing of the op amps because we are not using positive and negative power supplies.

(b) The capacitor and resistor values are simply the value of C you choose to use and the resistor values result from the following calculations. It's that simple.

Active band pass filter calculations

We'll proceed with a typical design example and say we need an audio filter for a CW receiver. Fc will be 750 Hz, gain per stage we'll fix at 3 and we'll make the bandwidth 150 Hz leading to Q = 750 / 150 = 5. For convenience C will equal 0.027 uF being a polyester capacitor we have on hand.

NOTE: If the calculations below look funny to you in Netscape, just hit the reload button - just another Netscape "quirk" we poor web designers have to live with.

Calculate R1 firstly:

R1 = Q / [ Ho * Wo * C ]

= 5 / [ 3 * 4712.4 * 0.027 X 10 - 6 ]

= 5 / 0.0003817 = 13099 or 13K

Next calculate R2:

R2 = Q / [ ( 2 * Q2 - Ho ) * C * Wo ]

= 5 / [ ( 2 * 52 - 3 ) * 0.027 X 10 - 6 * 4712.4 ]

= 5 / [ (50 - 3 ) * 0.000127234 ] = 5 / .00598 = 836 or 820R

Finally calculate R3:

R3 = 2 * Q / [ C * Wo ]

R3 = 10 / [ 0.027 X 10 - 6 * 4712.4 ]

R3 = 10 / [ 0.000127234 ] = 78,595 or 75K

Active band pass filter components

Resistors in this application could be typical 5% types but in Australia 1% metal film types in the E24 series don't cost much more anyway. The capacitor would be a 5% "Greencap" type. Notice with the resistors I've gone for the nearest standard E24 value.

The IC could be 741 op amps or for significantly improved performance select one of the better quality low noise types such as Philips NE/SA5534 premium low noise operational amplifiers (op-amps).

Pay particular attention to the two 10K resistors splitting the 12V power supply to



correctly bias the non-inverting (pin 3) input of the op-amps. You can add as many stages as you wish for sharper cut off (shape factor) but I don't believe more than two stages are usually justified

For this kind of active band pass filter don't try for very high Q's or very high gains, Ho, per stage. If I receive sufficient feedback (no pun intended) I might extend the series to other types of active filters.

Got a question on this topic?

If you are involved in electronics then consider joining our "electronics Questions and Answers" news group to ask your question there as well as sharing your thorny questions and answers. Help out your colleagues!.

The absolute fastest way to get your question answered and yes, I DO read most posts.

This is a mutual help group with a very professional air about it. I've learn't things. Not for absolute newcomers to ask questions BUT it is an excellent learning resource for lurkers.

RELATED TOPICS ON ACTIVE BAND PASS FILTERS

passive band pass filters passive high pass filters passive low pass filters NE5533 / NE5534 low noise operational amplifier data sheet - (109K) in PDF format. join our "electronics discussion group" Bibliography: - Philips Semiconductors - Semiconductors for Wireless Communications 1999 - IC17

NOW YOU CAN BUY BOOKS WHICH COVERS THESE TOPICS EXCEPTIONALLY WELL

The page cannot be displayed

The page you are looking for is currently unavailable. The Web site

might be experiencing technical difficulties, or you may need to adjust

your browser settings.

Please try the following:

� Click the Refresh button, or try again later.

� If you typed the page address in the Address bar, make sure

that it is spelled correctly.

� To check your connection settings, click the Tools

then click Internet Options. On the Connections



active bandpass filters

Documents