accurate approximate and analytical methods for...
TRANSCRIPT
Applied Mathematical Sciences, Vol. 9, 2015, no. 35, 1697 - 1719 HIKARI Ltd, www.m-hikari.com
http://dx.doi.org/10.12988/ams.2015.5182
Accurate Approximate and Analytical
Methods for Vibration and Bending
Problems of Plates: A Literature Survey
Thongperm Yoowattana1, Patiphan Chantarawichit1
Jakarin Vibooljak2 and Yos Sompornjaroensuk1,*
1 Department of Civil Engineering Mahanakorn University of Technology
Bangkok, 10530, Thailand * Correspondence author
2 Vibool Choke Ltd., Part Bangkok, 10110, Thailand
Copyright © 2015 T. Yoowattana et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Abstract
Three types of both accurate approximate and analytical solution methods, namely, the Rayleigh-Ritz method, the superposition method, and the integral transform method, that have been used with considerable success to solve many problems of plate having stress singularities either vibration or static bending problems are dealt with in this paper with emphasis on explaining the details of each method. In additions, some problems of plate that have been solved efficiently by these mentioned methods are also explored and reviewed.
Mathematics Subject Classification: 35Q74, 44A05, 65N30, 74H45, 74K20
Keywords: Analytical method, Approximate method, Integral transform method, Plate, Rayleigh-Ritz method, Static bending, Stress singularities, Superposition method, Vibration.
1698 Thongperm Yoowattana et al. 1 Introduction In solving the differential equation of plates, it is naturally desirable to obtain the exact solutions. However, the exact solutions are found only in a limited number of problems so that many research works on plate analysis have been conducted using a wide range of methods. There are two main types of solution that can be classified herein, namely, approximate solution and analytical solution which depended upon the methods used in the analysis. Analytical solutions are the most desirable, but not always easily attainable, as in the case of the plates with mixed boundary conditions (discontinuities in the edge support) [3-5,9,21,24-28,45,52-58,63] or plates with irregular boundaries [22,23,33,36-39,44,61]. This is due to the difficulty lied in the requirements to satisfy both, the governing differential equation and all of the boundary conditions exactly [59]. Approximate mathematical techniques have been developed to remedy the situation. Concerning bending problems of plates, a valuable study was made by Leissa et al.[32], to compare approximate methods.
Generally, the approximate methods can further be categorized into continuum types like the Rayleigh-Ritz method and the Galerkin method, and discrete types like the finite difference method, finite element method, boundary element method, and recently, the meshfree method. Some of them are, however, basically discussed herein depending upon whether the solutions satisfy the differential equation or the boundary conditions.
The Rayleigh-Ritz method [31] is an energy method that makes use of the energy concept by determining the maximum strain energy and maximum kinetic energy (only for the vibration problems) of the system and then, minimizing these energy terms to obtain the condition of equilibrium equations. An inherent advantage of this method is that no need to solve the governing differential equation, only the suitable series of functions are required to be chosen in satisfying exactly the prescribed geometric boundary conditions of the problem. Forced or natural boundary conditions may be ignored. In the Galerkin method, it only requires that the residual of the differential equation be orthogonal to each term of the series that satisfy the boundary conditions.
The finite element method is one of the powerful methods and has advanced with the development of computers. It has been very successful in finding the solution of various problems, particularly its applicability to problems having irregularly shaped boundaries, which involved in discretizing the numerical solution domain. However, incorrect results may be obtained if the element-type is poorly chosen to model and the number of elements is not enough to represent the overall domain properly.
The boundary element method is another numerical method which makes use of the fundamental solution of problem considered together with the reciprocal theorems. Its characteristic feature is that only the boundary of the solution domain is needed to be modeled. This leads to a relatively smaller set of resulting algebraic equations when compared to the finite element method, but the mathematical formulation of problems is more difficult than those of finite element method. Nevertheless, finite
Accurate approximate and analytical methods 1699 element method has become the first choice for many researchers, while the Rayleigh- Ritz method is still popular.
It is obvious that in the last five decades, there are many other approximate methods employed to analyze the plate problems. Most approximate solution methods appear to be limited to special problems. These solutions have a place as a check for the finite element method. However, it should not be forgotten that they are still only approximate in nature because the solutions do not satisfy exactly the governing differential equation, the all prescribed boundary conditions, or even both. With this reason, analytically oriented methods are still of importance to verify the results obtained from those approximate methods and they are good means to yield accurate numerical results since the solutions satisfy both the governing equation exactly and the boundary conditions with an arbitrary degree of exactitude. Two types of analytical method will be presented and described in details in the subsequent sections.
2 The Rayleigh-Ritz method Because the Rayleigh-Ritz method is one of the most effective approximate methods to obtain a highly accurate solution when a more enough terms of appropriate admissible functions being used, only the published papers relevant to this method that found in the scientific or technical literature will then be focused and explored in this section.
The Rayleigh method was first introduced by Lord Rayleigh in 1877 for solving the vibration problems to obtain the fundamental natural frequency of continuum systems by assuming the mode shape, and setting the maximum values of potential and kinetic energy in a cycle of motion equal to each other. In 1908, W. Ritz des- cribed his method for solving the boundary value problems, and the eigenvalue problems to determine the frequencies and their corresponding mode shapes by choosing multiple admissible displacement functions, and minimizing a functional involving both potential and kinetic energies [31]. Nevertheless, many research articles and many books have appeared to use the terms either Ritz method or Rayleigh- Ritz method in their works.
Before proceeding further to the detailed explanation of the Rayleigh-Ritz method, the governing biharmonic differential equation for the static bending problem of isotropic rectangular thin plates with uniform thickness (h) in terms of deflection function W(x,y) and subjected to a distributed load Q(x,y) can be given in form as
4 4 4
4 2 2 4
( , ) ( , ) ( , ) ( , )2
W x y W x y W x y Q x y
x x y y D
, (1)
and
3
212(1 )
EhD
, (2)
in which D is the plate rigidity, E and υ are the Young’s modulus and Poisson’s ratio
1700 Thongperm Yoowattana et al. of the plate, respectively [59].
For the strain energy (U) of the plate, it can be expressed by [59]
2 2
222 2
( , ) ( , )U ( , ) 2(1 )
2 A
D W x y W x yW x y
x y
22 ( , )W x y
dxdyx y
, (3)
whereas A is the total area of the plate and 2 is the Laplacian operator. The work done (W) that produced by the external load is
1W ( , ) ( , )
A
Q x y W x y dxdyD
. (4)
Thus, the corresponding total potential energy or energy functional (Π) can be defined by U W . (5)
In the case of free vibration problem of plates, the kinetic energy (T) has the form as given in Leissa [29],
2
2T [ ( , )]2 A
hW x y dxdy
, (6)
where ρ is the density of mass per unit area of the plate, and ω is the circular frequency of plate vibration.
Therefore, the energy functional for free vibration of the plates can be defined by the sum of expressions given in (3) and (6),
U T . (7)
Since the Rayleigh-Ritz method is applied, the deflection function W(x,y) can be chosen in terms of admissible function ψij(x,y) satisfying boundary conditions of the plate as
1 1
( , ) ( , )I J
ij iji j
W x y a x y
, (8)
where I, J are the highest integer numbers to be used in approximation of W(x,y), aij is defined to be the adjustable arbitrary coefficients, and the function ψij(x,y) may be assumed to be the algebraic polynomials or trigonometric functions satisfying essential (geometric) boundary conditions (i.e., deflection or slope) of the plate.
When the admissible functions ψij(x,y) cannot be satisfied in some points of
Ac bothto
wth
mde
inuntovi
botoif
ap
prTh
ccurate app
oundary conhen needed otal potentia
where χk is thhat includes
After thminimizing th
erivatives,
n which (10)ndeterminedo be the statiibration ana
It is geneound solutioo the exact sf the used ad
The follopplication of
Qatu et aroblem of trhe algebraic
proximate a
nditions, theto introduc
al energy (Π
he Lagrangthe terms inat, applyinghe total pote
is the systemd coefficienic equilibriu
alysis. erally well-k
ons for vibratsolution as tdmissible funowing paragf the Rayleigal.[44] accurapezoidal pc polynomia
Figure 1 G
nd analytic
e method oce into somΠ) equation.
*
e multipliernvolving thg the princiential energ
m of algebrants aij and χk
um equation
known that ttion frequenthe number nctions are fgraphs are agh-Ritz methurately preselates with cals were use
Geometry an
cal methods
of Lagrangeme constrain
. Thus,
1
(K
kk
W
rs and Π* is
he Lagrangeiple of min
gy with resp
*
0ija
,
aic linear eqk. Moreoverns or the equ
the Rayleighncies, and theof admissib
from a matha list of somhod for solvented the fircompletely fed for repre
nd dimensio
’s undetermnt condition
, )k kx y ,
s the new fo multipliers
nimum poteect to aij
by
quations to br, it may be uilibrium eq
h-Ritz methe upper bounble functionhematically c
me importantving the probrst known nfree boundaresenting the
ns of trapez
mined multips and then,
orm of eners. ential energy simply taki
be solved forstated that (
quations of m
od always pnd solutionss is sufficiencomplete sett works thatblem of thin atural frequries as showadmissible
zoidal plates
17
pliers (χk) a added to t
(
rgy function
gy theorem king the part
(1
r obtaining t(10) is knowmotion in fr
provides upps will converently large at of functiont related to telastic plate
uencies for twn in Figure functions.
s
01
are the
(9)
nal
or tial
10)
the wn ree
per rge and ns. the es. the e 1.
17
Vmwthcain
702
Leissa etV-notches (semathematicalwere guaranthat the cornease as beingn McGee et
Figure
Figure 4 G
t al.[33] anaee Figure 2lly completeteed and accer functions rg of the secal.[37].
e 2 Geomet
Figure 3 G
Geometry a
alyzed the f). Two sets e algebraic-tcelerated threpresentedtorial plates
try and dime
Geometry a
and dimensi
free vibratio of admissibtrigonometr
he convergethe singulars that demo
ensions of c
and dimensi
ions of circu
Thong
on problem ble displaceric polynomence to the erities at the nonstrated in
circular plat
ions of secto
ular plates w
gperm Yoow
of circular ement funct
mials and corexact frequ
notch angle [Figure 3 w
tes with V-n
orial plates
with clampe
wattana et a
plates havitions, namerner function
uencies. Not[61]. A spec
was also giv
notches
ed V-notch
al.
ing ly, ns, ted cial ven
Ac
clobcoth
(gan
ccurate app
Within tlamped V-nbtained in Monditions alhen shown in
Figur
McGee egeometry andnd free edge
F
proximate a
the same adnotches or riMcGee et along the stran Figure 5.
re 5 Circular
et al.[36] offd dimension
es (see Figur
Figure 6 Co
nd analytic
dmissible funigidly constal.[38]. An aight V-not
r plate havin
fered accurans shown in re 7).
ordinate sys
cal methods
unctions as utrained radiextension wtch edges [3
ng various V
ate free vibrFigure 6) w
stem definit
used beforeal cracks as
was also ma39]. The pro
V-notch bou
ation solutiowith combina
tions for a r
, the circulas seen in Fiade for the oblem confi
undary cond
ons for the rations of sim
rhombic pla
17
ar plates wiigure 4 can
various edfigurations a
ditions
rhombic platmply support
ate
03
ith be
dge are
tes ted
17
Fi
thth
704
igure 7 Rho
The cornhe obtuse anhe case of hi
Fi
Figur
ombic plate
ner functionngle in ordeighly skewe
igure 8 Geo
e 9 Geomet
es with comb
s were alsor to acceler
ed plates.
ometry of fr
try of cantil
bination of
accounted frate the conv
ree rectangu
levered rect
Thong
simply supp
for the bendvergence of
ular plate ha
angular plat
gperm Yoow
ported and f
ding stress sf solutions,
aving V-not
te having V
wattana et a
free edges
singularitiesespecially f
tch
V-notch
al.
s at for
Accurate approximate and analytical methods 1705
Huang et al.[22] obtained the accurate natural frequencies of rectangular plates having V-notches along their edges (see Figure 8) by using two sets of algebraic polynomials from a mathematically complete set of functions and corner functions as the admissible displacement functions. The results were demonstrated for free, square plates with a single V-notch only. Additionally, Huang et al.[23] extended the previous work [22] to obtain the results for the case of cantilevered rectangular plates with an edge V-notch as depicted in Figure 9, and further investigated the cases of V-notch angle equal to zero (slit). 3 The superposition method The present and the next sections aim to exhaustively propose the two efficient analytical solution methods for investigating the problem of plates with various boundary conditions because the plate problems have been analyzed and successfully solved using the advantages of these two methods. The first is referred to the building block superposition method [12] and the second is the integral transform method [51]. For the method of superposition, it has a little limitation on applications that the plates must have straight edges only. This is due to the solution of problems obtained by means of the Levy-type solution [59]. In the case of integral transform method, it can be applied to solve the problem of rectangular or circular plates.
Among the methods utilized for plate analysis in the past, one of them is known to be the superposition method developed by D.J. Gorman for analyzing free vibration of rectangular plates with numerous different types of boundary conditions and point supports. This powerful method gives the best values for the natural frequencies of plates having various aspect ratios when compared with other computing methods. It can, however, be noted that the method of superposition itself is not new, in fact it has long been in use for solving static plate problems for more decades.
The superposition method has been successfully applied for analysis of vibrations of plates having classical boundary conditions, such as, clamped support [10,35,46-48], free support [11,40] and simple support [34], and more complicated systems, such as elastic support [14,15], orthotropic [13,16,17,41,64], and shear deformable plates [42].
In many cases the results from the superposition method are the benchmarks for the natural frequencies because it is very efficient and accurate for a range of geometric shapes. However, it is interesting to note that the solutions obtained by this method would give an upper bound or a lower bound result depending on whether the boundary conditions of the building blocks (separate plate problems) are stiffer or more flexible than those of the actual system.
Based on the method mentioned in paragraph above, solutions always satisfy the governing differential equation and all boundary conditions. If the solutions are possible to sum infinity terms then the solutions would be exact. Therefore, the superposition method is an analytical-type method of solution because it is closed form as an infinite series [12]. Although it is of course necessary to truncate the series, it can be done at any highest desired degree of accuracy with the high speed electronic
17 co
crsmbubothorcaeqgoea
toadthmth
wcois
plfreofofdoto
706
omputer perThe conc
redit. By thimaller j-platuilding blocoundary conhe criterion friginal plate an be represquation exacoverning diach building
F
Once eaco obtain the djusted suchhe boundary
moment and vhe following
while j is theoordinates. Inot necessa
The follolate that solvee vibrationf superpositf the plate aoubly symmo the central
rformance. cept of impis method, tte problems cks as shownditions in wfor the net bproblem. Th
sented in thctly. This mifferential eg block can
igure 10 Bu
ch buildingoriginal pla
h that the suy conditionsvertical edgeg to be true,
e number ofIt may also barily uniqueowings are ved by mea
ns of compleion in which
and prescribmetric, doubl
co-ordinate
lementationthe original (two or mon in Figure which their boundary cohe solutions e form of L
means that thequation. In
be determin
uilding bloc
block is soate solution wuperimposeds, namely, te reaction. M
( ,w
f separate pbe noted thae. the research
ans of the suetely free reh their solut
bed boundarly antisymme axes of the
n on the sup plate probl
ore appropri10. Each bcombinatio
onditions sim of each bui
Levy-type soheir superpo
n addition, tned by adju
cks concept
olved separaw(ξ,η). The d set of builthe continu
Mathematica
1
) (j
ii
w
plate problemat the choice
h works invuperpositionectangular ptions satisfyry condition
metric, and sye plate were
Thong
perposition mlem will be ate plates) tuilding bloc
on of boundamilar to thosilding blockolution, whosition soluthe unknow
ustment of th
t in superpo
ately, the soconstants p
lding blocksuity of displally, the supe
, ) ,
ms, ξ and ηe of separate
volving the in method. Glate, see Figy identicallyns. Three clymmetric-anconsidered.
gperm Yoow
method is Dbroken into
that called thck will haveary conditiose specified wi(ξ,η) wherich satisfy ttions will al
wn constantshe boundary
sition metho
lutions are spresented in s satisfy all lacement, slerposition m
η are the noe plates or bu
isotropic recGorman [11]gure 11, usiny the differelasses of vibntisymmetriMochida an
wattana et a
D.J. Gormano a number he rectangue the differeons must mein the desir
ere i=1,2,3,…the governi
also satisfy ts appeared y conditions
od
superimposw(ξ,η) can constraints lope, bendi
method requir
(1
ondimensionuilding bloc
ctangular th] analyzed tng the methential equatibration modic with respend Ilanko [4
al.
n’s of lar ent eet red …,j ing the in
s.
sed be of
ing res
11)
nal cks
hin the
hod ion de, ect
40]
Ac rethanm
soreprdefom
suinspsufu[3
ccurate app
eexamined thhe finite diffend an upper
method and t
Figure 1
Considerolutions for estraint alonroblem wheresired distribor the free v
metrically dis
Figure
Li and Gupported recn Figure 13 paced point upport can bunction to re35] also dev
proximate a
he completeerence and sr bound forthe superpos
11 Geometr
r Figure 12the rectangg the edgesre elastic subutions alon
vibration anastributed rei
12 Rectangu
Gorman [34ctangular plin which thsupports. Th
be expanded epresent the veloped the
nd analytic
ely free rectauperposition
r the eigenvsition metho
ry and dimen
, Gorman [gular plates . Gorman [1
upport of botng the four ralysis of thininforcing be
ular plate w
4] analyticallates with ine line suppohe highlightas a cosine harmonic ffirst accura
cal methods
angular platn methods. Tvalues wereod, respecti
nsions of co
14] presentewith an arb
15] also obtth the rotatiorectangular n corner-supeams, or str
with a distrib
lly solved thnternal line ort was replt is that the series. Henc
forces in plaate analytica
tes for the boThe results s obtained frively.
ompletely fr
ed the first bitrarily disttained a soluonal and lateplate edgespported rectrips, attache
buted elastic
he free vibrsupport alo
laced by a liharmonic foce, Gorman
ate vibrational type solut
ounded eigeshowed that from the fin
free rectangu
comprehentributed elaution for theeral types ca. An extenstangular pla
ed to the pla
c rotational
ration problong the diagimited numborce respon[18] consid
n analysis. Ltion for the
17
envalues usia lower bou
nite differen
ular plate
nsive vibratiastic rotatione most genean take on asion was maates with symate edges [17
restraint
lem of simpgonals as se
mber of equanse at the podered the DirLi and Gorm
free vibrati
07
ing und nce
ion nal ral
any ade m- 7].
ply een lly int rac
man on
17 ofasgish
ha
708
f clamped res shown in iven and tabhapes were p
Figure 1
Figu
Figu
Saliba [4aving rigid p
ectangular pFigure 14. bulated for plotted for a
13 Simply s
ure 14 Clam
ure 15 Rect
46] gave the point support
plates with liThe comprea large numa square pla
upported re
mped rectan
tangular can
theoretical vts (Figure 15
ine support ehensive stumber of modate.
ectangular p
ngular plate
ntilever plat
vibration sol5). Only for t
Thong
along the diudy for the des and pla
plate with di
with diagon
te with rigid
lution for rethe case of s
gperm Yoow
iagonals, conatural freq
ate geometri
iagonal line
nal line supp
d point supp
ctangular caquare plate w
wattana et a
orner-to-cornquencies weies, and mo
e supports
ports
ports
antilever plawith four rig
al.
ner ere
ode
ates gid
Accurate approximate and analytical methods 1709 point supports symmetrically placed along the diagonals were given. However, a large number of plate aspect ratios and point support locations were also demonstrated in Saliba [47] together with the experimental results. It can be observed from this work that data obtained from the testing of plates show excellent agreement between the experimental and theoretical results where the maximum deviation is seen to be of the order of 4% with a mean deviation of about 1%. 4 The integral transform method Another analytical method that will be stated is the method of integral transforms. Various types of integral transform method have been used successfully to solve many kinds of mixed boundary value problems in engineering and in mathematical physics.
By the integral transform method, most problems are usually reduced to the final equation form of integral equations of special type [49] depending on the integral transform techniques used [51] and some of their solutions have already been provided in Polyanin and Manzhirov [43]. If the closed-form solutions of integral equation are not possible to be determined due to the complexity of the kernel then the numerical treatments would be made there [1,2].
A more comprehensive presentation of mixed boundary value problems using the method of integral transforms can be found in the textbook of Sneddon [50]. However, it is remarkable that the main task for obtaining the final integral equation governing the problem considered instead of the differential equation, some certain identities involving the integral representations are needed to be employed. These may necessarily be consulted with the help of handbook of Gradshteyn and Ryzhik [19].
It is generally well-known in the plate problems that the moment singularities existed in the problem of plates with mixed boundary conditions are in the order of an inverse-square-root type at the transition points of discontinuous support [61-62]. Moreover, the necessity of singularity considerations in the static bending problems of plates with mixed boundary conditions were given by Leissa et al.[32], while the eigenvalue problems (free vibration and buckling) were discussed by Leissa [30]. In their works, it is concluded that the accurate solutions cannot be achieved without the use of appropriate singularity functions. With this conclusion, one of the advantages of the integral transform method is that it can be coped with the singularity at the points of discontinuity of the boundary conditions.
Therefore, a brief review of important works that pertained to solve the mixed boundary value problems of plates using the method of integral transforms are listed in the following paragraphs.
Yang [63] dealt with the static bending problem of a rectangular plate with an internal line support in which the plate configuration is illustrated in Figure 16. The problem was reduced to the solution of a singular integral equation governing the pressure distribution along the internal line support by means of the Hilbert transform techniques. Based on a technique proposed by Westmann and Yang [60], the problem
17 ofincoinin
an[5thof
re
710
f uniformly n Figure 17 wonditions as ntegral transntegral equa
F
The samnalyze the fr56] as shownhe inverse-sf internal lin
Additionectangular p
loaded rectawas analyze dual-seriesforms. The
ation of the s
Figure 16 R
Fi
me method aree vibrationn in Figure quare-root ne support [nally, Keer plates with m
angular platd by Keer a equations afinal equatiosecond kind
Rectangular
igure 17 Re
as previouslyn and stabili18 and cracmoment sin
[61] and in tand Stahl [2
mixed edge c
tes with straand Sve [26]and solved bon was in thd.
r plate with
ectangular c
y treated inity of rectancked rectangngularities wthe vicinity 25] analyzeconditions b
Thong
aight line of ] who formuby using thehe form of in
an internal
cracked plat
n Keer and Sngular platesgular plates were taken of the crack
ed the free vbetween clam
gperm Yoow
f cracks that ulated the mie method ofnhomogene
line suppor
tes
Sve [26] was with an in[57]. It caninto accoun
k tips [62]. vibration anmped and sim
wattana et a
demonstratixed boundaf finite Hankeous Fredho
rt
as extended nternal suppon be noted thnt at the en
nd buckling mple suppo
al.
ted ary kel lm
to ort hat nds
of rts
Ac (FthIt thge
ccurate app
Figure 19). Inhe simple an
can be notehat the integeneous Fred
Figure
Figure 19
Figure
A more c
proximate a
n the cases ond free suppoed for the eiggral equationdholm-type
18 Rectang
9 Rectangul
20 Rectang
complicated
nd analytic
of rectangulorts (Figure genvalue prons governingof the secon
ular plate h
ar plates wi
gular plates
d problem, w
cal methods
lar plate with20), they w
oblems of plg to the prond kind.
having an in
ith mixed ed
with mixed
which is eith
h mixed bouwere treated
lates with moblems cons
nternal line s
dges (simpl
d edges (sim
her square pl
undary condiby Kiattikom
mixed boundideration we
support at th
y supported
mply support
lates or recta
17
ditions betwemol et al.[2
dary conditiowere the hom
he center
d-clamped)
ted-free)
angular plat
11
een 7].
ons mo-
tes
1712 Thongperm Yoowattana et al. having mixed boundary conditions around all edges, was analyzed by Kiattikomol et al. [28] and Thonchangya [58]. In the recent years, Sompornjaroensuk and Kiattikomol [52,54,55] demonstrated the rigorous treatment of uniformly loaded rectangular plates with a partial internal line support. The deformations and stress resultants of the plates including some important physical quantities, namely, the strain energy and the stress intensity factors were presented in the form of graphs and tables.
In the field of contact problems of plates [20], the advancing contact between a plate and sagged supports under a uniformly distributed load was first presented by Dundurs et al.[9] using the Hankel integral transform method. It is worth noticing that the shear distribution along the line of sagged supports was singular in the order of square root type corresponding to the nature of contact problems [6-8]. In addition, the extent of contact was increased with increasing the loading and the support reaction was not proportional to the applied external load.
The receding contact at the vicinity of a right-angle corner of semi-infinite plate with unilaterally constrained was formulated and solved by Keer and Mak [24]. The finite Fourier integral transform was used through the dual-series equations and reduced to the singular integral equation. For the case of finite plates, Dempsey et al. [5] studied the receding contact problem of square plate using the method similar to that of Keer and Mak [24]. Moreover, Dempsey and Li [3,4] further investigated the problems of rectangular plate with sagged and no sag supports. The mixed boundary conditions were formulated as a coupled system of dual-series equations and then, reduced to a system of two simultaneously Cauchy singular integral equations. Recently, a similar problem with respect to the previous work that made by Dempsey et al.[5] was reexamined by Sompornjaroensuk and Kiattikomol [53] using the method of Hankel integral transforms together with introducing an inverse-square-root shear singularity at the tips of contact interval between the plate and the unilateral supports [6]. The governing equation was finally reduced to an inhomogeneous Fredholm integral equation of the second kind. Furthermore, the obtained results were in agreement with the previous work, and also well-compared to other numerical methods which are the finite element method [45] and boundary element method [21].
Additionally, it may also be expected, by observing the previous works, that the final form of equations governing to the problem of rectangular plate having mixed boundary conditions in two directions would be a coupled system of integral equations similar to those treated by Keer and Stahl [25], Keer and Mak [24], Dempsey and Li [3], and Thonchangya [58]. Since the Hankel integral transforms are selected to be applied in the static bending problem of rectangular plates, the integral equations are in the form of inhomogeneous Fredholm-type of the second kind.
1
1 11 1 12 2 1
0
( ) [ ( , ) ( ) ( , ) ( )] ( )K r r K r r dr f , (12)
and
1
2 21 1 22 2 2
0
( ) [ ( , ) ( ) ( , ) ( )] ( )K r r K r r dr f , (13)
where ρ is an independent variable and 0 ≤ ρ ≤ 1, r is a dummy variable, Φ1(ρ) and
Accurate approximate and analytical methods 1713 Φ2(ρ) are the unknown auxiliary functions to be determined, and introduced in the Hankel integral transform techniques which related to the unknown constants of integration of plate’s differential equation, f1(ρ) and f2(ρ) are known functions that involved to the load applied on the plate, and K11(ρ,r) through K22(ρ,r) are the kernels of integral equation.
5 Summary In closing, the efficient accurate methods which are the Rayleigh-Ritz method, the superposition method, and the integral transform method are presented and reviewed for solving the eigenvalue and boundary value problems of plate having stress singu- larities due to geometry or boundary condition. Some important relevant research works that have been treated successfully for this class of mentioned problems are also explored and then exhaustively explained in the present paper.
References [1] C.T.H. Baker, The Numerical Treatment of Integral Equations, Clarendon Press, Oxford, 1978. [2] L.M. Delves and J. Walsh, Numerical Solution of Integral Equations, Clarendon Press, Oxford, 1974. [3] J.P. Dempsey and H. Li, Rectangular plates on unilateral edge supports: Part 1- Theory and numerical analysis, Journal of Applied Mechanics, ASME, 53(1986), 146- 150. http://dx.doi.org/10.1115/1.3171702 [4] J.P. Dempsey and H. Li, Rectangular plates on unilateral edge supports: Part 2- Implementation; concentrated and uniform loading, Journal of Applied Mechanics, ASME, 53(1986), 151-156. http://dx.doi.org/10.1115/1.3171703 [5] J.P. Dempsey, L.M. Keer, N.B. Patel, and M.L. Glasser, Contact between plates and unilateral supports, Journal of Applied Mechanics, ASME, 51(1984), 324- 328. http://dx.doi.org/10.1115/1.3167620 [6] J. Dundurs and M. Stippes, Role of elastic constants in certain contact problems, Journal of Applied Mechanics, ASME, 37(1970), 965-970. http://dx.doi.org/10.1115/1.3408725 [7] J. Dundurs, Dependence of stress on Poisson’s ratio in plane elasticity, International Journal of Solids and Structures, 3(1967), 1013-1021.
1714 Thongperm Yoowattana et al. http://dx.doi.org/10.1016/0020-7683(67)90026-1 [8] J. Dundurs, Effect of elastic constants on stress in a composite under plane deformation, Journal of Composite Materials, 1(1967), 310-322. [9] J. Dundurs, K. Kiattikomol, and L.M. Keer, Contact between plates and sagged supports, Journal of the Engineering Mechanics Division, ASCE, 100(1974), 445- 456. [10] D.J. Gorman and R. Singhal, Free vibration analysis of cantilever plates with step discontinuities in properties by the method of superposition, Journal of Sound and Vibration, 253(2002), 631-652. http://dx.doi.org/10.1006/jsvi.2001.4067 [11] D.J. Gorman, Free vibration analysis of the completely free rectangular plate by the method of superposition, Journal of Sound and Vibration, 57(1978), 437-447. http://dx.doi.org/10.1016/0022-460x(78)90322-x [12] D.J. Gorman, Free Vibration Analysis of Rectangular Plates, Elsevier North Holland, Inc., New York, 1982. [13] D.J. Gorman, Accurate free vibration analysis of the completely free orthotropic rectangular plate by the method of superposition, Journal of Sound and Vibration, 165 (1993), 409-420. http://dx.doi.org/10.1006/jsvi.1993.1267 [14] D.J. Gorman, Free vibration analysis of rectangular plates with step-wise dis- continuities in rotational stiffness along the edges, Journal of Sound and Vibration, 166 (1993), 397-408. http://dx.doi.org/10.1006/jsvi.1993.1303 [15] D.J. Gorman, A general solution for the free vibration of rectangular plates with arbitrarily distributed lateral and rotational elastic edge support, Journal of Sound and Vibration, 174(1994), 451-459. http://dx.doi.org/10.1006/jsvi.1994.1287 [16] D.J. Gorman, Accurate free vibration analysis of the orthotropic cantilever plate, Journal of Sound and Vibration, 181(1995), 605-618. http://dx.doi.org/10.1006/jsvi.1995.0161 [17] D.J. Gorman, Free vibration analysis of corner-supported rectangular plates with symmetrically distributed edge beams, Journal of Sound and Vibration, 263(2003), 979- 1003. http://dx.doi.org/10.1016/s0022-460x(03)00269-4
Accurate approximate and analytical methods 1715 [18] D.J. Gorman, A critical look at the Dirac function and its role in representing concentrated harmonic forces in vibration analysis of structures, Proceedings of the 6th International Symposium on Vibrations of Continuous Systems, California, July 23-27, 2007, 10-12. [19] I.N. Gradshteyn and I.M. Ryzhik, Table of Integrals, Series, and Products, 4th ed., Academic Press, New York, 1956. [20] E.I. Grigolyuk and V.M. Tolkachev, Contact Problems in the Theory of Plates and Shells, MIR Publishers, Moscow, 1987. [21] C. Hu and G.A. Hartley, Boundary element analysis of thin plates unilaterally edge supported, Engineering Analysis with Boundary Element, 12(1993), 47- 55. http://dx.doi.org/10.1016/0955-7997(93)90068-v [22] C.S. Huang, A.W. Leissa, and S.C. Liao, Vibration analysis of rectangular plates with edge V-notches, International Journal of Mechanical Sciences, 50(2008), 1255- 1262. http://dx.doi.org/10.1016/j.ijmecsci.2008.05.005 [23] C.S. Huang, S.C. Liao, and I.C. Lee, Vibration of cantilevered rectangular plates with edge V-notches of slits, Proceedings of the 7th International Symposium on Vibrations of Continuous Systems, Zakopane, Poland, July 19-24, 2009, 24- 26. [24] L.M. Keer and A.F. Mak, Loss of contact in the vicinity of a right-angle corner for a simply supported, laterally loaded plate, Journal of Applied Mechanics, ASME, 48(1981), 597-600. http://dx.doi.org/10.1115/1.3157680 [25] L.M. Keer and B. Stahl, Eigenvalue problems of rectangular plates with mixed edge conditions, Journal of Applied Mechanics, ASME, 39(1972), 513-520. http://dx.doi.org/10.1115/1.3422709 [26] L.M. Keer and C. Sve, On the bending of cracked plates, International Journal of Solids and Structures, 6(1970), 1545-1559. http://dx.doi.org/10.1016/0020-7683(70)90063-6 [27] K. Kiattikomol, L.M. Keer, and J. Dundurs, Application of dual series to rectan- gular plates, Journal of the Engineering Mechanics Division, ASCE, 100(1974), 433- 443. [28] K. Kiattikomol, S. Porn-anupapkul, and N. Thonchangya, Application of dual series equations to a square plate with varying corner supported lengths, Japan-Thai Civil Engineering Conference, Proceedings of The Recent Advances in Structural
1716 Thongperm Yoowattana et al. Engineering, 14-15 March, 1985, Bangkok, 115-130. [29] A.W. Leissa, Vibration of Plates, Reprinted ed., Acoustical Society of America, Washington, DC., 1993. [30] A.W. Leissa, Singularity considerations in membrane, plate and shell behaviors, International Journal of Solids and Structures, 38(2001), 3341-3353. http://dx.doi.org/10.1016/s0020-7683(00)00262-6 [31] A.W. Leissa, The historical bases of the Rayleigh and Ritz methods, Journal of Sound and Vibration, 287(2005), 961-978. http://dx.doi.org/10.1016/j.jsv.2004.12.021 [32] A.W. Leissa, W.E. Clausen, L.E. Hulbert, and A.T. Hopper, A comparison of approximate methods for the solution of plate bending problems, AIAA Journal, 7 (1969), 920-928. http://dx.doi.org/10.2514/3.5245 [33] A.W. Leissa, O.G. McGee, and C.S. Huang, Vibrations of circular plates having V-notches of sharp radial cracks, Journal of Sound and Vibration, 161(1993), 227-239. http://dx.doi.org/10.1006/jsvi.1993.1068 [34] N. Li and D.J. Gorman, Free Vibration Analysis of Simply Supported Rectangular Plates with Internal Line Support along Diagonals, Journal of Sound and Vibration, 165(1993), 361-368. http://dx.doi.org/10.1006/jsvi.1993.1262 [35] N. Li and D.J. Gorman, Free vibration analysis of clamped rectangular plates with line support along the diagonals, Journal of Sound and Vibration, 173 (1994), 591-598. http://dx.doi.org/10.1006/jsvi.1994.1248 [36] O.G. McGee, J.W. Kim, and A.W. Leissa, The influence of corner stress singu- larities on the vibration characteristics of rhombic plates with combinations of simply supported and free edges, International Journal of Mechanical Sciences, 41(1999), 17-41. http://dx.doi.org/10.1016/s0020-7403(97)00120-3 [37] O.G. McGee, A.W. Leissa, and C.S. Huang, Vibrations of completely free sec- torial plates, Journal of Sound and Vibration, 164(1993), 565-569. http://dx.doi.org/10.1006/jsvi.1993.1236 [38] O.G. McGee, A.W. Leissa, C.S. Huang, and J.W. Kim, Vibrations of circular plates with clamped V-notches or rigidly constrained radial cracks, Journal of Sound and Vibration, 181(1995), 185-201.
Accurate approximate and analytical methods 1717 http://dx.doi.org/10.1006/jsvi.1995.0134 [39] O.G. McGee, A.W. Leissa, J.W. Kim, and Y.S. Kim, Vibration of plates with constrained V-notches or cracks, Journal of Engineering Mechanics, ASCE, 129 (2003), 812-822. http://dx.doi.org/10.1061/(asce)0733-9399(2003)129:7(812) [40] Y. Mochida and S. Ilanko, Bounded eigenvalues of completely free rectangular plates, Proceedings of the 6th International Symposium on Vibrations of Continuous Systems, California, July 23-27, 2007, 22-24. [41] F. Moussu and M. Nivoit, Determination of elastic constants of orthotropic plates by a modal analysis/method of superposition, Journal of Sound and Vibration, 165 (1993), 149-163. http://dx.doi.org/10.1006/jsvi.1993.1248 [42] F. Ohya, M. Ueda, T. Uchiyama, and M. Kikuchi, Free vibration analysis by the superposition method of rectangular Mindlin plates with internal columns resting on uniform elastic edge supports, Journal of Sound and Vibration, 289(2006), 1-24. http://dx.doi.org/10.1016/j.jsv.2005.01.030 [43] A.D. Polyanin and A.V. Manzhirov, Handbook of Integral Equations, 2nd ed., Chapman & Hall/CRC, Boca Raton, 2008. http://dx.doi.org/10.1201/9781420010558 [44] M.S. Qatu, N.A. Jaber, and A.W. Leissa, Natural frequencies for completely free trapezoidal plates, Journal of Sound and Vibration, 167(1993), 183-191. http://dx.doi.org/10.1006/jsvi.1993.1328 [45] N.J. Salamon, T.P. Pawlak, and F.F. Mahmoud, Plates in unilateral contact with simple supports: Pressure loading, Journal of Applied Mechanics, ASME, 53 (1986), 141-145. http://dx.doi.org/10.1115/1.3171701 [46] H.T. Saliba, Theoretical free vibration analysis of rectangular cantilever plates with rigid point supports, Journal of Sound and Vibration, 164(1993), 383-397. http://dx.doi.org/10.1006/jsvi.1993.1224 [47] H.T. Saliba, Experimental free vibration analysis of rectangular cantilever plates with rigid point supports, Journal of Sound and Vibration, 171(1994), 459-472. http://dx.doi.org/10.1006/jsvi.1994.1134 [48] H.T. Saliba, Transverse free vibrations of right triangular thin plates with com- binations of clamped and simply supported boundary conditions: A highly accurate
1718 Thongperm Yoowattana et al. simplified solution, Journal of Sound and Vibration, 183(1995), 765- 778. http://dx.doi.org/10.1006/jsvi.1995.0285 [49] T.O. Shaposhnikova, R.S. Anderssen, and S.G. Mikhlin, Integral Equations - A Reference Text, Noordhoff International Publishing, Leyden, 1975. [50] I.N. Sneddon, Mixed Boundary Value Problems in Potential Theory, John Wiley & Sons, New York, 1966. [51] I.N. Sneddon, The Use of Integral Transforms, McGraw-Hill, New York, 1972. [52] Y. Sompornjaroensuk and K. Kiattikomol, Dual-series equations formulation for static deformation of plates with a partial internal line support, Theoretical and Applied Mechanics, 34(2007), 221-248. http://dx.doi.org/10.2298/tam0703221s [53] Y. Sompornjaroensuk and K. Kiattikomol, The solution of certain loss of contact between a plate and unilateral supports, Theoretical and Applied Mechanics, 34 (2007), 289-308. http://dx.doi.org/10.2298/tam0704289s [54] Y. Sompornjaroensuk and K. Kiattikomol, Exact analytical solutions for bending of rectangular plates with a partial internal line support, Journal of Engineering Mathematics, 62(2008), 261-267. http://dx.doi.org/10.1007/s10665-007-9207-x [55] Y. Sompornjaroensuk and K. Kiattikomol, Inverse square root moment singu- larities in rectangular plates containing an internal line support, International Journal of Computational Methods, 6(2009), 1-21. http://dx.doi.org/10.1142/s0219876209001693 [56] B. Stahl and L.M. Keer, Vibration and buckling of a rectangular plate with an internal support, Quarterly Journal of Mechanics and Applied Mathematics, 25(1972), 467-478. http://dx.doi.org/10.1093/qjmam/25.4.467 [57] B. Stahl and L.M. Keer, Vibration and stability of cracked rectangular plates, International Journal of Solids and Structures, 8(1972), 69-91. http://dx.doi.org/10.1016/0020-7683(72)90052-2 [58] N. Thonchangya, Analysis of the bending of a uniformly loaded rectangular plate with variable width corner supports, International Journal of Computational Engi- neering Science, 2(2001), 31-42. http://dx.doi.org/10.1142/s1465876301000222
Accurate approximate and analytical methods 1719 [59] S.P. Timoshenko and S. Woinowsky-Krieger, Theory of Plates and Shells, 2nd ed., McGraw-Hill, Singapore, 1959. [60] R.A. Westmann and W.H. Yang, Stress analysis of cracked rectangular beams, Journal of Applied Mechanics, ASME, 34(1967), 693-701. http://dx.doi.org/10.1115/1.3607763 [61] M.L. Williams, Surface stress singularities resulting from various boundary conditions in angular corners of plates under bending, Proceedings of the First U.S. National Congress of Applied Mechanics, ASME, 1952, vol.1, 325-329. [62] M.L. Williams, The bending stress distribution at the base of a stationary crack, Journal of Applied Mechanics, ASME, 28(1961), 78-82. http://dx.doi.org/10.1115/1.3640470 [63] W.H. Yang, On an integral equation solution for a plate with internal support, Quarterly Journal of Mechanics and Applied Mathematics, 21(1968), 503-513. http://dx.doi.org/10.1093/qjmam/21.4.503 [64] S.D. Yu and W.L. Cleghorn, Generic free vibration of orthotropic rectangular plates with clamped and simply supported edges, Journal of Sound and Vibration, 163(1993), 439-450. http://dx.doi.org/10.1006/jsvi.1993.1180 Received: February 10, 2015; Published: March 5, 2015