accreditation no: lab 016pnac.org.pk/wp-content/uploads/2017/03/lab-016-sgs-lahore.pdf · issue...

ACCREDITATION

DOCUMENT

F-06/02

Issue Date: 10/08/15

Rev. No: 07

LAB 016

of 14

Accreditation No: LAB 016

Awarded to

SGS Pakistan (Pvt) Ltd. Lahore, Pakistan.

The scope of accreditation is in accordance with the standard specifications outlined in

the following page(s) of this document. The accredited scope shall be visible and

legible in areas such as customer service, sample-receiving section etc and shall not

mislead its users.

The accreditation was first time granted on 2511-2008 by Pakistan National

Accreditation Council.

The laboratory complies with the requirements of ISO/IEC 17025:2005.

The accreditation requires regular surveillance, and is valid until 24-11-2017.

The decision of accreditation made by Pakistan National Accreditation Council

implies that the organization has been found to fulfill the requirements for

accreditation within the scope.

The organization however, itself is responsible for the results of performed

measurements/tests.

PAKISTAN NATIONAL ACCREDITATION COUNCIL

_____________ ____________________________

Date Director General

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Testing Laboratory.

Accreditation Scope of SGS Pakistan(Pvt) ltd. Lahore, Pakistan.

Permanent laboratory premises Plot # 7, Din Muhammad Town,

( Opposite Police Training Institute) 19-Km off Multan Road, Chuhang,

Lahore, Pakistan.

Materials/

Products

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit.

Uncertainty

of

Measurement

(where

applicable)

MU (±)

Standard

specification/

Technique

Equipment

Used

All textile

material /

products /

physical

tests

Fabric weight

per unit area

Depends upon the

behavior of the

material-

0.1 gm/m² 1.66 %

ASTM D3776/D3776

M − 09a (Reapproved

2013)ISO

3801:1977

Ends &picks

(woven fabric)

Depends upon the

type of fabrication 1 thread 1 thread

ASTM D3775 − 12

Stitch density

(knitted fabric)

Depends upon the


ASTM D3887 − 96

(Reapproved

2008)/BS

5441: 1988

Ends &

Picks(Woven

Fabric)

Depends upon the


ISO-

7211/2:1984

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/

Products

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit.

Uncertainty

of

Measurement

(where

applicable)

MU (±)

Standard

specification/

Technique

Equipment

Used

All textile

material /

products /

physical

tests

Tearing strength

( Elmendorf )

Pendulum

A 0.00 to 0.8 N

B8.0 to 16 N

C 16 to 32 N

D 32 to 64 N

E 64 to 128 N

0.1 N

Warp 2.3 %

Weft 2.7 %

ASTM D

1424:09(re-

approved

2013) / ISO

13937-1:2000

Spray rating test

Spray rating

photographs, from 1

till 5 scale rating

Qualitative

(assessment

made

visually by

using

photographs

)

0.5

AATCC

22:2014 /

ISO

4920:2012

Pilling

resistance

Pilling photographs

from 1 till 5 scale

rating

Qualitative

assessment

made

visually with

pilling

replicas

0.5

ASTM D3512/D3512

M − 16 (Reapproved

2014)

Tensile strength

Max force:

03 load range

a) 3000 N

b) 600

c) 120

0.01 N

0.01 N

Warp 1.8 %

Weft 2.1 %

ASTM D5034 − 09

(Reapproved

2013)/

ASTM D

5035:2011 (Reapproved

2015)/

Abrasion

Qualitative test as

assessment made

visually

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5

BS EN ISO

12947-2 :

1998

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/

Products

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit.

Uncertainty

of

Measurement

(where

applicable)

MU (±)

Standard

specification/

Technique

Equipment

Used

All textile

material /

products /

physical

tests

Tear strength

( Single rip )

Max force:

03 load range

a) 3000 N

b) 600

c) 120

0.01N

0.01N

Warp 2.5 %

Weft 3.5 %

ASTM D

2261-2013

Tear strength

(trapezoid)

Max force:

03 load range

a) 3000 N

b) 600

c) 120

0.01 N

0.01 N

Warp 2.8 %

Weft 3.2 %

ASTM D

5587:2015

Tensile strength

( grab/strip

method)-

measuring

breaking force.

Max force:

03 load range

a) 3000 N

b) 600

c) 120

0.01N

0.01N

Warp 1.2 %

Weft 1.4 %

BS EN ISO

13934-1

2013/ BS EN

ISO 13934-2

2014

Pilling

resistance-

sample visual

assessment is

required

2 – 999999 cycles

(qualitative test as

assessment made

visually by using

pilling photographs)

Visual

assessment

using pilling

photographs

0.5 BS EN ISO

12945-2:2000

Pilling

resistance-

sample visual

assessment is

required

2 – 999999 cycles

(qualitative test as

assessment made

visually by using

pilling photographs)

Visual

assessment

using pilling

photographs

0.5

BS 5811:1986

/BS EN ISO

12945.1:2001

ISO 12945-1

2000

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/

Products

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit.

Uncertainty

of

Measurement

(where

applicable)

MU (±)

Standard

specification/

Technique

Equipment

Used

All textile

material /

products /

physical

tests

Tear strength

Max force:

03 load range

a) 3000 N

b) 600

c) 120

0.01 N

0.01 N

Warp 2.1 %

Weft 2.9 %

BS EN ISO

13937-

2/3:2000

Seam slippage

Max force:

a) 200 N

0.01 N

0.01 N

Warp 3.8 %

Weft 4.8 %

BS 3320:1988

Superseded

by ISO

13936-

1(2004) used

only upon

confirmation

Bursting

strength

Max force:

03 load range

a) 3000 N

b) 600

c) 120

0.01 N

3.7 %

ASTM D

3787:2016

Bursting

strength

Max force-kpa

15kpa – 1250 kpa 12.5 Kpa 2.6 %

BS EN ISO

13938-2:1999

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment

used

All textile

material /

products /

physical

tests

Seam Slippage Max. Force 3000 N 0.1 N Warp 4.2 %

Weft 5.3 %

BS EN ISO

13936-1/ 2

:2004

ASTM

434:1995

Seam strength Max. Force 3000 N 0.1 N Warp 3.2 %

Weft 4.3 %

ISO 13935

1/2:2014

Determination

of Extension

and Modulus

120 N `

1 %

0.9 %

BS EN 14704 -

1 :2005

Slide Fastness

( Zips) 300 Kgf

.1 Kgf or

0.01N 5.4 % BS 3084:2006

Stretch

Properties of

Fabrics Woven

from Stretch

Yarns

4 Lbf, & 3 Lbf 1 % 2.3 %

ASTM D3107

− 07 (Reapproved

2015)

Fabric Width 3.5 m 1 mm 0.1 %

ASTM D3774

− 96 (Reapproved

2016)

Leather

Formaldehyde

Content 20 ppm – 600 ppm 20 ppm 0.30 ppm

ISO/ 17226-2

/:2008 DIN 53315 (1996-

03)

Cr VI Content 3 ppm – 125 ppm 3 ppm 0.020 ppm

ISO

17075:2007

BSEN

420:1994

DIN 53314 (1996-04) /CEN/TS

14495 :2003

Azo Amines 5 ppm – 30 ppm 5 ppm For all amines

0.020 ppm -

ISO 17234-

1:2015/ ISO

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment

used

0.091 ppm 17234-2:2011

pH 1 – 14 1.0 0.05 ISO 4045 :2008

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

All textile

material /

products /

Washing &

CF tests

Fabric

/Garment

shrinkage

Depends upon the

type of fabrication

0.4 % 0.2%

AATCC

135:2015/

AATCC 150:2012

0.33 % 0.2% ISO 3759-5077-

6330:2012

Appearance

after wash

Smoothness

appearance replicas

Qualitative

(assessment

made

visually by

using the

SA Replicas

)

0.5 AATCC 124:2014

Skewness after

wash

Depend upon actual

fabrication 0.3% 0.2% AATCC 179:2012

Colour

fastness to

washing

Grey scale from 1 till

5, GS for colour

change and staining

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5

ATCC 61:2013,

BS EN ISO

105:CO6 :2010

ISO

105:CO8:2010-

CO9:2001-C10-

2006

Colour

fastness to

perspiration


5, GS for colour

change and staining

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5

AATCC 15: 2013

/BS EN ISO 105 -

EO4:2013

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

All textile

material /

products /

Washing &

CF tests

Colour

fastness to

rubbing


5, GS for colour

change and staining

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5

AATCC

8:2013/BS EN

ISO

105X12:2016/

ISO 105X12:2016

Colour

fastness to

water


5, GS for colour

change and staining

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5

AATCC 107:2013

/BS EN ISO 105

EO1:2013

Colour

fastness to sea

water


5, GS for colour

change and staining

Colour

fastness to

sea water

0.5

AATCC 106:2013

/ BS EN ISO 105

EO2:2013

Colour

fastness to dry

cleaning


5, GS for colour

change and staining

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5 BS EN ISO 105

DO1:2010

Colour

fastness to non

chlorine bleach


5, GS for colour

change and staining

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5 AATCC 172:

2010

Colour

fastness to

light


5, GS for colour

change

Qualitative

(assessment

made

visually by

using the

grey scales)

0.5 AATCC –

16:2014

Color Fastness

to Artificial

Light: Xenon

Arc Fading

Blue Wool Scale 1 to

8 Qualitative 0.5

BS EN ISO 105

BO2:2014

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

All textile

material /

products /

Washing &

CF tests

Lamp Test.

Phenolic

yellowing


5, GS for colour

change and staining

Qualitative

(visual

assessment)

0.5

Courtlaulds

research,

ISO 105

X18:2007

Colour

fastness to

chlorinated

water


5, GS for colour

change and staining

Qualitative

(visual

assessment)

0.5 BS EN ISO 105

EO3 :2010

Print

Durability

Grey Scale Rating 1 to

5

0.5 0.5 IHTM – 1, BHS

12-A

Smoothness of

Seams in

Fabrics after

Repeated

Home

Laundering

Smoothness Replicas

Scale range from 1-5 0.5 0.5

AATCC 88 B :

2014

Retention of

Creases in

Fabrics after

Repeated

Home

Laundering

Smoothness Replicas

Scale range from 1-5 0.5 0.5

AATCC 88

C :2014

Colourfastness

to commercial

and domestic

Laundering


5

0.5 0.5 ISO 105

CO8:2010

Colourfastness

to Hot pressing


5 0.5 0.5

ISO 105

X11:1994/BS EN

ISO X11 :1996

Fiber Analysis 0.1 to 100 % 0.1 % 0.3 %

AATCC 20A

2014 /ISO

1833 :2006 /In

accordance with

73/44/EEC and

96/73/EC as

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

All Textile

Materials /

Products/

Chemical

tests

All Textile

Materials /

Products/

Chemical

tests

amended by

2006/2/EC

pH Value of

aqueous

extract

1 - 13 0.1 AATCC 0.021

ISO 0.023

AATCC 81 :2012

ISO 3071 :2005

Azo Amines 5 ppm – 30 ppm 5 ppm

For all amines

0.020 ppm -

0.091 ppm

ISO 14362-

1/2:2012

Formaldehyde

Content 20 ppm – 600 ppm 20 ppm 0.30 ppm

ISO 14184-

1/2:2011

/ AATCC 112

:2008 , JPLAW

112 / JISL 1041

:2011

Lead &

Cadmium

Content

20 ppm – 375 ppm 20 ppm 5.1 ppm

US Public law

110-314 ASTM E

1613-04 ASTM E

1645-01 (2007)

CPSC-CH-E-

1001- 08 CPSC-

CH-E- 1002- 08

CPSC-CH-E-

1003-09 16 CFR

1303-1

All Textile

Materials /

Products/

Regulatory

Flammability 1 Sec – 9999 Sec 1 sec 1.4 %

16CFR

1610:2008ASTM

D 1230:2010 (re –

approved 2016)

TEXTILE

S

/ACCESS

ORIES

Determination

of Sharp point Qualitative

Visual

assessment

N/A

ASTM F 963 / 16

CFR 1500.48/ EN

71-1: 2014)

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

TEXTILE

S

/ACCESS

ORIES

Determination

of Sharp Edge Qualitative Visual

assessment

N/A

ASTM F 963 / 16

CFR 1500.49/ EN

71-1 : 2014)

Determination

of Torque 2.3 kg /cm

4.6 kg/cm 0.2 kg

0.07 Kg/cm

ASTM F 963 / 16

CFR 1500.49/ EN

71-1 : 2014)

Determination

of small parts

Qualitative Visual

assessment

N/A

ASTM F 963 / 16

CFR 1501/ EN

71-1 :2014)

Tension test 10 lbs – 15 lbs

1 lb Visual 16CFR 1500.51

/52/53

Leather and

Footwear

Tear Strength

1-3000 N

1 N

3.26 N

ISO 3377 1:2011-

ISO 3377 -2 2002

EN 13571:2002,

STM -162.

Tensile

strength

1-3000 N 1 N 2.13 N

ISO-3376 2011,

STM-43,

Distension of

grain

elastability-

lastometer ball

burst

1-3000 N 1 N 9.45 N STM-24, ISO

3379 :2015

Adhesion of

finish

0-900 N

0.1 N

0.56 N

EN ISO 11644:

2009

VAMP FLEX

TEST –

RESISTANCE

TO

CREASING

AND

CRACKING

Qualitative

Visual

assessment

Visual

SATRA TM 25.

Flexing

Resistance

(Bally)

Qualitative

Visual

assessment

Visual

ISO 5402:2011

ROSS FLEX Qualitative

Visual

assessment

Visual

BS 5131 2.1

1991; STM 60;

EN 12769

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

:1980:04

RESISTANCE

OF

FOOTWEAR

TO FLEXING

Qualitative Visual

assessment

Visual

STM 92.

Flexing

Resistance of

outsole

Qualitative

Visual

assessment

Visual STM 133;

Abrasion

Resistance of

Leather

Qualitative Visual

assessment

Visual

ISO-20344 :2011,

ASTM-D4966

:2012 e1，STM

31

Colour

Fastness

to Rubbing

Qualitative Visual

assessment

0.5

EN ISO 17700 :

2004, EN ISO

11640 :2012,

STM 167, ASTM

D 5053:03(2015)

Water and

perspiration

fastness

Qualitative Visual

assessment

0.5 STM 335, BS EN

ISO 1164 :2012,

IUF 426

Colourfastness

to light

Qualitative Visual

assessment

0.5 STM 160; ISO

105 BO2 :2014

Density 0.1 mg/mm3 to 1.6

mg/mm3

0.1mg/ mm3 .05 mg/mm3 ISO 2781 2008

Dry cleaning Qualitative Visual

assessment

0.5

ISO 11643:2009

BS EN ISO

11643:2009

EN ISO

11643:2009

Washing Qualitative Visual

assessment

0.5

ISO 15702 , ISO

15703

:1999

Shrinkage

temperature

Qualitative Visual

assessment

ISO 3380 2015 &

IUP 16

Thickness 0.1-12mm 0.01 mm 0.033 mm IUP 4;

ISO 2589:2002

Abrasion of ISO 4649 2010/

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

outsole 0 – 300 mg

1 mg 5 mg STM 174

Textile /

Leather /

Plastic

Alkylphenol

and

Alkylphenol

Ehoxylate

( AP, APEO )

0.05 to 3 ppm

0.05 to 3

ppm

0.01 ppm

RSTS-CHEM-

213-1

Textile

/Surface

Coating/

Plastic

Phthalates

Contents

0.3 to 10 ppm

0.3 to 10

ppm

0.3 and 0.5

ppm

CPSC—CH-

1001.09.3 ISO

14389:2014

All Types

of Gloves

Abrasion

Resistance

Level 1 – 5

Visual

N/A

EN 388:2003

Blade Cut

Resistance

1.2, 2.5, 5.0, 10 and

20

0 Level

N/A

Tear

Resistance

10,25,50,75

0 Level

N/A

Puncture

Resistance

20, 60, 100, 150

0 Level

N/A

Water Vapour

absorption

8 mg/cm2

0.1 to 1000

mg/cm2

0.1 mg/cm2

EN 420

:2003+A12009

Water vapour

Permeability /

Transmission

5 - mg/cm2/

/hour

0.1 to 1000

mg/cm2

0.1 mg/cm2

Dexterity

Level 1 - 5

Level 1

N/A

Size

Size 6 – 11

Size 6

N/A

Cr VI

3-125 mg/Kg

3 mg/Kg

0.02 mg/Kg

ACCREDITATION

DOCUMENT

F-06/02


Rev. No: 07

LAB 016

_____________ ____________________________

Date Director

of 14

Materials/P

roducts

tested

Types of test/

Properties

measured

Range of

measurement

Minimum

detection

limit

Uncertainty

of

Measurement

(where

applicable)

Standard

specification/

Techniques/

equipment used

pH 1-14 0.01 0.05

All Leather

and Textile

Products

Formaldehyde

20 – 600 mg/Kg

20 mg/Kg

0.30 mg/Kg

GB/T 2912

pH

1-4

0.1

0.5

(GB/T 7573,

GB/T 2724)

AZO dyes

analysis

2.5 to 30

2.5

For all amines

0.020 ppm -

0.091 ppm

(GB/T 17592,

GB/T 23344)

accreditation no: lab 016pnac.org.pk/wp-content/uploads/2017/03/lab-016-sgs-lahore.pdf · issue...

Documents