7/27/2019 Access Controller 9901A

1/2

1BTS-9901A Standalone Access Controller Product introduction

This Radio Frequency Identification (RFID) access controller is the 3rd

generation controller. With newly added functions it is one of the most advanced

standalone access controller. The controller is built on powerful modern Central

Processing Unit. It manages up to 500 card holders, and access mode can be set t o

Authorized Card Only, Authorized Card or Public PIN and Authorized Card +

Personal PIN. Additional functions includes: door sensor input, alarm relay output,

safe mode and anti-break. Door bell, exit button and electric locks can be

connected to the controller. When users forget the programming password, they

can restore the factory default password without erasing the card holders

information. It is ideal for different occasions such as business apartment,

governmental, factory buildings and so on.

2. Product specification

Item Specification

1 Voltage 12VDC+10%; Current 1.2A

2 Relay output 12VDC/2A

3 Dimension 116mm x 116mm x 20mm

4 Weight 180g

5 Temperature -10~55

6 Humidity 20%~90%

7 Capacity 500 cards, each with one Personal Password and one

Public Password

8 Reading Distance 5~15CM

9 Compatible Cards EM or EM compatible cards 125KHz

3. LED and Buzzer

LED:

Event Red LED Green LED

Normal Flash once a second

Authorized card On

Unauthorized card On

Door o en On

Programming mode On Flash quickly

Programming confirm On On

Alarm Flash quickly

Buzzer:

Event Buzzer

Authorized card Two short bee s

Unauthorized card One lon bee

Valid key input One short beep

Valid Password entered Two short beeps

Invalid Password entered One long beep

In alar Continuous lo

n bee s

4. Functions and settings

1) Default password: programming password: 990101, public

password: 1234, personal password: 0000.

2) Enter programming mode: Press [*]+[990101]

3) Settings (Enter programming mode firstly, letters inside []

represents the key to press)

A. Change programming password:

Press [0]+ [new 6 digits pa ssword]+ [confirm new password]

B. Change access mode:

Press [1]+[0] (Authorized Card or Public Password)

Press [1]+[1] (Authorized Card and Personal Password)

Note: If access mode is set to Authorized Card and Personal

Password, card holders should input personal password within 10

seconds after presenting their cards to the reader. The personal

password can not be used alo ne.The default mode is Authorized

Card Only.

C. Set authorized card:

Press [5]+ [3 digits card index 1]+ [card index 2]+ !+[card index

n]+[*]

If the cards are presented in sequence, all of them will be enrolled

after [*] pressed. Card index ranges from 001 to 500 exclusively.

Default personal password: 0000

D. Delete authorized card: (in 3 ways):

Press [86] to delete all cards

Press [7]+presenting the card+[*] to delete specific card

Press [7]+ [3 digits card index]+[*] to delete specific card

E. Set door opening time:

Press [2]+time+[TT]

[TT] is seconds in 2 digits. Default is 3 seconds, that is TT=03.

F. Set door sensor input:

Press [6]+[0] to disable the input

Press [6]+[1] to enable the input

G. Set alarm delay time:

Press [82]+[TT]

[TT] is seconds in 2 digits. If it i s 3 seconds, that is TT=03.

H. Set door sensor alarm:

Press [8]+[0] to disable

Press [8]+[1] to enable

I. Set anti-dismantle alarm:

Press [4]+[0] to disable

Press [4]+[1] to enable

J. Change public password:

Press [3]+ [new 4 digits password] (default 1234)

When public password or personal password is 0000, password is

invalid under access mode of "card or password#

K. Press [86] to restore factory defaults.

4)

Exit programming mode

Press [*] to exit programming mode.

5) Change personal password

A.Press [1]+[2] to disable changing personal password.

B.Press [1]+[3] to enable changing personal password.

C.Press [#]+presenting the card+[ 4 digits original password]

(default 0000) +[4 digits new password] +[ confirm new password]

6)

Restore the programming password

Short J2 on board to restore the default programming password. All

other information will be kept.

5. Frequently asked questions

Q: After the lock is opened, there are 8 short beeps.

A: The controller needs higher voltage; the power supply should be

checked.

7/27/2019 Access Controller 9901A

2/2