abaqus 6.11, example problems manual, vol. 2
TRANSCRIPT
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
1/600
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
2/600
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
3/600
Abaqus
Example Problems Manual
Volume II
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
4/600
Legal Notices
CAUTION: This documentation is intended for qualified users who will exercise sound engineering judgment and expertise in the use of the AbaqusSoftware. The Abaqus Software is inherently complex, and the examples and procedures in this documentation are not intended to be exhaustive or to apply
to any particular situation. Users are cautioned to satisfy themselves as to the accuracy and results of their analyses.
Dassault Systèmes and its subsidiaries, including Dassault Systèmes Simulia Corp., shall not be responsible for the accuracy or usefulness of any analysis
performed using the Abaqus Softwar e or the procedures, examples, or explanations i n this documentation. Dassault Systèmes and its subsidiaries shall not
be responsible for the consequ ences of any erro rs or omissions that may appear in thi s documen tation.
The Abaqus Software is available only under license from Dassault Systèmes or its subsidiary and may be used or reproduced only in accordance with the
terms of such license. This documentation is subject to the terms and conditions of either the software license agreement signed by the parties, or, absent
such an agreement, the then current software license agreement to which the documentation relates.
This documentation and the software described in this documentation are subject to change without prior notice.
No p art of this do cumentation may be repr oduced or distributed in any form without p rior written permi ssion of Dassault Systèmes or its subsidiary.
The Abaqus Software is a product of Dassault Systèmes Simulia Corp., Providence, RI, USA.
© Dassault Systèmes, 2011
Abaqus, the 3DS logo, SIMULIA, CATIA, and Unified FEA are trademarks or registered trademarks of Dassault Systèmes or its subsidiaries in the United
States and/or other countries.
Other company, product, and service names may be trademarks or service marks of their respective owners. For additional information concerning
trademarks, copyrights, and licenses, see the Legal Notices in the Abaqus 6.11 Release Notes.
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
5/600
Locations
SIMULIA Worldwide Headquarters Rising Sun Mills, 166 Valley Street, Providence, RI 02909–2499, Tel: +1 401 276 4400,
Fax: +1 401 276 4408, [email protected], http://www.simulia.com
SIMULIA European Headquarters Stationsplein 8-K, 6221 BT Maastricht, The Netherlands, Tel: +31 43 7999 084,
Fax: +31 43 7999 306, [email protected]
Dassault Systèmes’ Centers of Simulation Excellence
United States Fremont, C A, Tel: +1 510 794 5891, s imulia.west.s upport@3ds .com
West Lafayette, IN, Tel: +1 765 497 1373, [email protected]
Northville, MI, Tel: +1 248 349 4 669, [email protected]
Woodbury, MN, Tel: +1 612 424 9044, [email protected]
Beachwood, OH, Tel: +1 216 378 1070, [email protected]
West Chester, OH, Tel: +1 513 275 1430, [email protected]
Warwick, RI, Tel: +1 401 739 3637, [email protected]
Lewisville, TX, Tel: +1 972 221 6500, [email protected]
A ust ralia Ri ch mond VI C, Tel: +61 3 94 21 2 900, simu lia. au .su ppo rt@ 3ds. co m
A ustria Vienna, Tel: +43 1 22 707 200, [email protected]
B enelux M aarss en, The Netherlands , Tel: +31 346 585 710, s imulia.benelux.support@3ds. com
C anada Tor onto, ON, Tel : +1 41 6 402 2 219 , sim ulia. greatlakes. in fo @3 ds. com
C hi na Beij ing, P. R. Chin a, Tel: +8610 653 6 22 88, sim uli a.cn.s upp ort@ 3ds. comShanghai, P. R. China, Tel: +8621 3856 8000, [email protected]
F inland Espoo, Tel: +358 40 902 2973, [email protected]
France Velizy Villacoublay C edex, Tel: +33 1 61 62 72 72, s imulia.fr. support@3ds. com
G ermany A achen, Tel: +49 241 474 01 0, [email protected]
Munich, Tel: +49 89 543 48 77 0, [email protected]
I ndia Chennai, Tamil Nadu, Tel: +91 44 43443000, sim [email protected]
I taly Lainate MI, Tel: +39 02 334306150, [email protected]
Japan Tokyo, Tel: +81 3 5442 6300, simulia.tokyo.support@3 ds.com
Osaka, Tel: +81 6 7730 2703, [email protected]
Yokohama-shi, Kanagawa, Tel: +81 45 470 9381, [email protected] orea Mapo-Gu, Seoul, Tel: +82 2 785 6707/8, [email protected]
Latin America Puerto Madero, Buenos Aires, Tel: +54 11 4312 8700, [email protected]
Scandinavia Väs terås, Sweden, Tel: +46 21 150870, s imulia.nordic. info@3ds .com
United Kingdom Warrington, Tel: +44 1925 830900, [email protected]
Authorized Support Centers
Czech & Slovak Republics Synerma s. r. o., Psáry, Prague-West, Tel: +420 603 145 769, [email protected]
G reece 3 Dim en si onal Data Systems, Cr ete, Tel: +3 0 28 210 400 12, sup port@ 3dd s. gr
I srael A DC OM, Givataim , Tel: + 972 3 732 5311 , shmul ik .k eidar@ adcom si m. co .il
Malaysia WorleyParsonsAdvanced Analysis, Kuala Lumpur, Tel: +603 2039 9000, [email protected] New Zealand Matrix Applied Com puting Ltd., Auckland, Tel: +64 9 623 1223 , abaqu [email protected]
Poland BudSoft Sp. z o.o., Poznań, Tel: +48 61 8508 466, [email protected]
Russia, Belarus & Ukraine TESIS Ltd., Moscow, Tel: +7 495 612 44 22, [email protected]
Singapore WorleyParsons Advanced Analysis, Singapore, Tel: +65 6735 8444, [email protected]
South Africa Finite Element Analysis Services (Pty) Ltd., Parklands, Tel: +27 21 556 6462, [email protected]
Spain & Portugal Principia Ingenieros Consultores, S.A., Madrid, Tel: +34 91 209 1482, [email protected]
Taiwan Simutech Solution Corporation, Taipei, R.O.C., Tel: +886 2 2507 9550, [email protected]
Thailand WorleyParsons Advanced Analysis, Singapore, Tel: +65 6735 8444, [email protected]
Tur key A -Z tech Ltd ., Istanb ul, Tel: +90 216 361 8 850 , inf o@ a- ztech. co m. tr
Complete contact information is available at http://www.simulia.com/locations/locations.html.
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
6/600
Preface
This section lists various resources that are available for help with using Abaqus Unified FEA software.
Support
Both technical engineering support (for problems with creating a model or performing an analysis) and
systems support (for installation, licensing, and hardware-related problems) for Abaqus are offered through
a network of local support of fices. Regional contact information is listed in the front of each Abaqus manual
and is accessible from the Locations page at www.simulia.com.
Support for SIMULIA products
SIMULIA provides a knowledge database of answers and solutions to questions that we have answered,
as well as guidelines on how to use Abaqus, SIMULIA Scenario Definition, Isight, and other SIMULIA
products. You can also submit new requests for support. All support incidents are tracked. If you contact
us by means outside the system to discuss an existing support problem and you know the incident or support
request number, please mention it so that we can consult the database to see what the latest action has been.
Many questions about Abaqus can also be answered by visiting the Products page and the Support page at www.simulia.com.
Anonymous ftp site
To facilitate data transfer with SIMULIA, an anonymous ftp account is available on the computer
ftp.simulia.com. Login as user anonymous, and type your e-mail address as your password. Contact support
before placing files on the site.
Training
All of fices and representatives offer regularly scheduled public training classes. The courses are offered in
a traditional classroom form and via the Web. We also provide training seminars at customer sites. All
training classes and seminars include workshops to provide as much practical experience with Abaqus as
possible. For a schedule and descriptions of available classes, see www.simulia.com or call your local of fice
or representative.
Feedback
We welcome any suggestions for improvements to Abaqus software, the support program, or documentation.
We will ensure that any enhancement requests you make are considered for future releases. If you wish to
make a suggestion about the service or products, refer to www.simulia.com. Complaints should be addressed
by contacting your local of fice or through www.simulia.com by visiting the Quality Assurance section of
the Support page.
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
7/600
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
8/600
CONTENTS
Forming analyses
Upsetting of a cylindrical billet: quasi-static analysis with mesh-to-mesh solution
mapping (Abaqus/Standard) and adaptive meshing (Abaqus/Explicit) 1.3.1Superplastic forming of a rectangular box 1.3.2
Stretching of a thin sheet with a hemispherical punch 1.3.3
Deep drawing of a cylindrical cup 1.3.4
Extrusion of a cylindrical metal bar with frictional heat generation 1.3.5
Rolling of thick plates 1.3.6
Axisymmetric forming of a circular cup 1.3.7
Cup/trough forming 1.3.8
Forging with sinusoidal dies 1.3.9
Forging with multiple complex dies 1.3.10
Flat rolling: transient and steady-state 1.3.11
Section rolling 1.3.12
Ring rolling 1.3.13
Axisymmetric extrusion: transient and steady-state 1.3.14
Two-step forming simulation 1.3.15
Upsetting of a cylindrical billet: coupled temperature-displacement and adiabatic
analysis 1.3.16
Unstable static problem: thermal forming of a metal sheet 1.3.17
Inertia welding simulation using Abaqus/Standard and Abaqus/CAE 1.3.18
Fracture and damage
A plate with a part-through crack: elastic line spring modeling 1.4.1
Contour integrals for a conical crack in a linear elastic infinite half space 1.4.2
Elastic-plastic line spring modeling of a finite length cylinder with a part-through axial
flaw 1.4.3Crack growth in a three-point bend specimen 1.4.4
Analysis of skin-stiffener debonding under tension 1.4.5
Failure of blunt notched fiber metal laminates 1.4.6
Debonding behavior of a double cantilever beam 1.4.7
Debonding behavior of a single leg bending specimen 1.4.8
Postbuckling and growth of delaminations in composite panels 1.4.9
Import analysesSpringback of two-dimensional draw bending 1.5.1
Deep drawing of a square box 1.5.2
2. Dynamic Stress/Displacement Analyses
Dynamic stress analyses
Nonlinear dynamic analysis of a structure with local inelastic collapse 2.1.1
Detroit Edison pipe whip experiment 2.1.2
ii
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
9/600
CONTENTS
Rigid projectile impacting eroding plate 2.1.3
Eroding projectile impacting eroding plate 2.1.4
Tennis racket and ball 2.1.5Pressurized fuel tank with variable shell thickness 2.1.6
Modeling of an automobile suspension 2.1.7
Explosive pipe closure 2.1.8
Knee bolster impact with general contact 2.1.9
Crimp forming with general contact 2.1.10
Collapse of a stack of blocks with general contact 2.1.11
Cask drop with foam impact limiter 2.1.12
Oblique impact of a copper rod 2.1.13Water sloshing in a baffled tank 2.1.14
Seismic analysis of a concrete gravity dam 2.1.15
Progressive failure analysis of thin-wall aluminum extrusion under quasi-static and
dynamic loads 2.1.16
Impact analysis of a pawl-ratchet device 2.1.17
High-velocity impact of a ceramic target 2.1.18
Mode-based dynamic analyses
Analysis of a rotating fan using substructures and cyclic symmetry 2.2.1
Linear analysis of the Indian Point reactor feedwater line 2.2.2
Response spectra of a three-dimensional frame building 2.2.3
Brake squeal analysis 2.2.4
Dynamic analysis of antenna structure utilizing residual modes 2.2.5
Steady-state dynamic analysis of a vehicle body-in-white model 2.2.6
Eulerian analyses
Rivet forming 2.3.1
Impact of a water-filled bottle 2.3.2
Co-simulation analyses
Closure of an air-filled door seal 2.4.1
Dynamic impact of a scooter with a bump 2.4.2
iii
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
10/600
CONTENTS
Volume II
3. Tire and Vehicle Analyses
Tire analyses
Symmetric results transfer for a static tire analysis 3.1.1
Steady-state rolling analysis of a tire 3.1.2
Subspace-based steady-state dynamic tire analysis 3.1.3
Steady-state dynamic analysis of a tire substructure 3.1.4
Coupled acoustic-structural analysis of a tire filled with air 3.1.5
Import of a steady-state rolling tire 3.1.6
Analysis of a solid disc with Mullins effect and permanent set 3.1.7
Tread wear simulation using adaptive meshing in Abaqus/Standard 3.1.8
Dynamic analysis of an air-filled tire with rolling transport effects 3.1.9
Acoustics in a circular duct with flow 3.1.10
Vehicle analyses
Inertia relief in a pick-up truck 3.2.1
Substructure analysis of a pick-up truck model 3.2.2Display body analysis of a pick-up truck model 3.2.3
Continuum modeling of automotive spot welds 3.2.4
Occupant safety analyses
Seat belt analysis of a simplified crash dummy 3.3.1
Side curtain airbag impactor test 3.3.2
4. Mechanism Analyses
Resolving overconstraints in a multi-body mechanism model 4.1.1
Crank mechanism 4.1.2
Snubber-arm mechanism 4.1.3
Flap mechanism 4.1.4
Tail-skid mechanism 4.1.5
Cylinder-cam mechanism 4.1.6
Driveshaft mechanism 4.1.7
Geneva mechanism 4.1.8
Trailing edge flap mechanism 4.1.9
Substructure analysis of a one-piston engine model 4.1.10
Application of bushing connectors in the analysis of a three-point linkage 4.1.11
Gear assemblies 4.1.12
5. Heat Transfer and Thermal-Stress Analyses
Thermal-stress analysis of a disc brake 5.1.1
iv
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
11/600
CONTENTS
A sequentially coupled thermal-mechanical analysis of a disc brake with an Eulerian
approach 5.1.2
Exhaust manifold assemblage 5.1.3Coolant manifold cover gasketed joint 5.1.4
Conductive, convective, and radiative heat transfer in an exhaust manifold 5.1.5
Thermal-stress analysis of a reactor pressure vessel bolted closure 5.1.6
6. Fluid Dynamics and Fluid-Structure Interaction
Conjugate heat transfer analysis of a component-mounted electronic circuit board 6.1.1
7. Electromagnetic Analyses
Piezoelectric analyses
Eigenvalue analysis of a piezoelectric transducer 7.1.1
Transient dynamic nonlinear response of a piezoelectric transducer 7.1.2
Joule heating analyses
Thermal-electrical modeling of an automotive fuse 7.2.1
8. Mass Diffusion Analyses
Hydrogen diffusion in a vessel wall section 8.1.1
Diffusion toward an elastic crack tip 8.1.2
9. Acoustic and Shock Analyses
Fully and sequentially coupled acoustic-structural analysis of a muffler 9.1.1Coupled acoustic-structural analysis of a speaker 9.1.2
Response of a submerged cylinder to an underwater explosion shock wave 9.1.3
Convergence studies for shock analyses using shell elements 9.1.4
UNDEX analysis of a detailed submarine model 9.1.5
Coupled acoustic-structural analysis of a pick-up truck 9.1.6
Long-duration response of a submerged cylinder to an underwater explosion 9.1.7
Deformation of a sandwich plate under CONWEP blast loading 9.1.8
10. Soils Analyses
Plane strain consolidation 10.1.1
Calculation of phreatic surface in an earth dam 10.1.2
Axisymmetric simulation of an oil well 10.1.3
Analysis of a pipeline buried in soil 10.1.4
Hydraulically induced fracture in a well bore 10.1.5
Permafrost thawing–pipeline interaction 10.1.6
v
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
12/600
CONTENTS
11. Structural Optimization Analyses
Topology optimization analyses
Topology optimization of an automotive control arm 11.1.1
Shape optimization analyses
Shape optimization of a connecting rod 11.2.1
12. Abaqus/Aqua Analyses
Jack-up foundation analyses 12.1.1Riser dynamics 12.1.2
13. Design Sensitivity Analyses
Overview
Design sensitivity analysis: overview 13.1.1
Examples
Design sensitivity analysis of a composite centrifuge 13.2.1
Design sensitivities for tire inflation, footprint, and natural frequency analysis 13.2.2
Design sensitivity analysis of a windshield wiper 13.2.3
Design sensitivity analysis of a rubber bushing 13.2.4
14. Postprocessing of Abaqus Results Files
User postprocessing of Abaqus results files: overview 14.1.1
Joining data from multiple results files and converting file format: FJOIN 14.1.2
Calculation of principal stresses and strains and their directions: FPRIN 14.1.3
Creation of a perturbed mesh from original coordinate data and eigenvectors: FPERT 14.1.4
Output radiation viewfactors and facet areas: FRAD 14.1.5
Creation of a data file to facilitate the postprocessing of elbow element results:
FELBOW 14.1.6
vi
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
13/600
TIRE AND VEHICLE ANALYSES
3. Tire and Vehicle Analyses
• “Tire analyses,” Section 3.1
• “Vehicle analyses,” Section 3.2
• “Occupant safety analyses,” Section 3.3
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
14/600
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
15/600
TIRE ANALYSES
3.1 Tire analyses
• “Symmetric results transfer for a static tire analysis,” Section 3.1.1
• “Steady-state rolling analysis of a tire,” Section 3.1.2
• “Subspace-based steady-state dynamic tire analysis,” Section 3.1.3
• “Steady-state dynamic analysis of a tire substructure,” Section 3.1.4
• “Coupled acoustic-structural analysis of a tire filled with air,” Section 3.1.5• “Import of a steady-state rolling tire,” Section 3.1.6
• “Analysis of a solid disc with Mullins effect and permanent set,” Section 3.1.7
• “Tread wear simulation using adaptive meshing in Abaqus/Standard,” Section 3.1.8
• “Dynamic analysis of an air-filled tire with rolling transport effects,” Section 3.1.9
• “Acoustics in a circular duct with flow,” Section 3.1.10
3.1–1
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
16/600
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
17/600
TIRE RESULTS TRANSFER
3.1.1 SYMMETRIC RESULTS TRANSFER FOR A STATIC TIRE ANALYSIS
Product: Abaqus/Standard
This example illustrates the use of the *SYMMETRIC RESULTS TRANSFER option as well as the
*SYMMETRIC MODEL GENERATION option to model the static interaction between a tire and a rigid
surface.
The *SYMMETRIC MODEL GENERATION option (“Symmetric model generation,” Section 10.4.1
of the Abaqus Analysis User’s Manual) can be used to create a three-dimensional model by revolving an
axisymmetric model about its axis of revolution or by combining two parts of a symmetric model, where one part is the original model and the other part is the original model reflected through a line or a plane. Both
model generation techniques are demonstrated in this example.
The *SYMMETRIC RESULTS TRANSFER option (“Transferring results from a symmetric mesh or
a partial three-dimensional mesh to a full three-dimensional mesh,” Section 10.4.2 of the Abaqus Analysis
User’s Manual) allows the user to transfer the solution obtained from an axisymmetric analysis onto a
three-dimensional model with the same geometry. It also allows the transfer of a symmetric three-dimensional
solution to a full three-dimensional model. Both these results transfer features are demonstrated in this
example. The results transfer capability can signifi
cantly reduce the analysis cost of structures that undergosymmetric deformation followed by nonsymmetric deformation later during the loading history.
The purpose of this example is to obtain the footprint solution of a 175 SR14 tire in contact with a flat
rigid surface, subjected to an inflation pressure and a concentrated load on the axle. Input files modeling a
tire in contact with a rigid drum are also included. These footprint solutions are used as the starting point in
“Steady-state rolling analysis of a tire,” Section 3.1.2, where the free rolling state of the tire rolling at 10 km/h
is determined and in “Subspace-based steady-state dynamic tire analysis,” Section 3.1.3, where a frequency
response analysis is performed.
Problem description
The different components of the tire are shown in Figure 3.1.1–1. The tread and sidewalls are made of
rubber, and the belts and carcass are constructed from fi ber-reinforced rubber composites. The rubber is
modeled as an incompressible hyperelastic material, and the fi ber reinforcement is modeled as a linear
elastic material. A small amount of skew symmetry is present in the geometry of the tire due to the
placement and 20.0° orientation of the reinforcing belts.
Two simulations are performed in this example. The fi
rst simulation exploits the symmetry in thetire model and utilizes the results transfer capability; the second simulation does not use the results
transfer capability. Comparisons between the two methodologies are made for the case where the tire
is in contact with a flat rigid surface. Input files modeling a tire in contact with a rigid drum are also
included. The methodology used in the first analysis is applied in this simulation. Results for this case
are presented in “Steady-state rolling analysis of a tire,” Section 3.1.2.
The first simulation is broken down into three separate analyses. In the first analysis the inflation of
the tire by a uniform internal pressure is modeled. Due to the anisotropic nature of the tire construction,
the inflation loading gives rise to a circumferential component of deformation. The resulting stress field
3.1.1–1
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
18/600
TIRE RESULTS TRANSFER
is fully three-dimensional, but the problem remains axisymmetric in the sense that the solution does not
vary as a function of position along the circumference. Abaqus provides axisymmetric elements with
twist (CGAX) for such situations. These elements are used to model the infl
ation loading. Only half thetire cross-section is needed for the inflation analysis due to a reflection symmetry through the vertical
line that passes through the tire axle (see Figure 3.1.1–2). We refer to this model as the axisymmetric
model.
The second part of the simulation entails the computation of the footprint solution, which
represents the static deformed shape of the pressurized tire due to a vertical dead load (modeling the
weight of a vehicle). A three-dimensional model is needed for this analysis. The finite element mesh
for this model is obtained by revolving the axisymmetric cross-section about the axis of revolution.
A nonuniform discretization along the circumference is used as shown in Figure 3.1.1–3. In addition,the axisymmetric solution is transferred to the new mesh where it serves as the initial or base state in
the footprint calculations. As with the axisymmetric model, only half of the cross-section is needed
in this simulation, but skew-symmetric boundary conditions must be applied along the midplane of
the cross-section to account for antisymmetric stresses that result from the inflation loading and the
concentrated load on the axle. We refer to this model as the partial three-dimensional model.
In the last part of this analysis the footprint solution from the partial three-dimensional model is
transferred to a full three-dimensional model and brought into equilibrium. This full three-dimensional
model is used in the steady-state transport example that follows. The model is created by combiningtwo parts of the partial three-dimensional model, where one part is the mesh used in the second analysis
and the other part is the partial model reflected through a line. We refer to this model as the full three-
dimensional model.
A second simulation is performed in which the same loading steps are repeated, except that the full
three-dimensional model is used for the entire analysis. Besides being used to validate the results transfer
solution, this second simulation allows us to demonstrate the computational advantage afforded by the
Abaqus results transfer capability in problems with rotational and/or reflection symmetries.
Model definition
In the first simulation the inflation step is performed on the axisymmetric model and the results are
stored in the results files (.res, .mdl, .stt, and .prt). The axisymmetric model is discretized
with CGAX4H and CGAX3H elements. The belts and ply are modeled with rebar in surface elements
embedded in continuum elements. The ROUNDOFF TOLERANCE parameter on the *EMBEDDED
ELEMENT option is used to adjust the positions of embedded element nodes such that they lie exactly on
host element edges. This feature is useful in cases where embedded nodes are offset from host elementedges by a small distance caused by numerical roundoff. Eliminating such gaps reduces the number
of constraint equations used to embed the surface elements and, hence, improves performance. The
axisymmetric results are read into the subsequent footprint analysis, and the partial three-dimensional
model is generated by Abaqus by revolving the axisymmetric model cross-section about the rotational
symmetry axis. The *SYMMETRIC MODEL GENERATION, REVOLVE option is used for this
purpose. The partial three-dimensional model is composed of four sectors of CCL12H and CCL9H
cylindrical elements covering an angle of 320°, with the rest of the tire divided into 16 sectors of
C3D8H and C3D6H linear elements. The linear elements are used in the footprint region. The use of
3.1.1–2
TIRE RESULTS TRANSFER
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
19/600
TIRE RESULTS TRANSFER
cylindrical elements is recommended for regions where it is possible to cover large sectors around the
circumference with a small number of elements. In the footprint region, where the desired resolution
of the contact patch dictates the number of elements to be used, it is more cost-effective to use linear
elements. The road (or drum) is defined as an analytical rigid surface in the partial three-dimensional
model. The results of the footprint analysis are read into the final equilibrium analysis, and the full
three-dimensional model is generated by reflecting the partial three-dimensional model through a
vertical line using the *SYMMETRIC MODEL GENERATION, REFLECT=LINE option. The line
used in the reflection is the vertical line in the symmetry plane of the tire, which passes through the axis
of rotation. The REFLECT=LINE parameter is used, as opposed to the REFLECT=PLANE parameter,
to take into account the skew symmetry of the tire. The analytical rigid surface as defined in the partial
three-dimensional model is transferred to the full model without change. The three-dimensional fi
niteelement mesh of the full model is shown in Figure 3.1.1–4.
In the second simulation a datacheck analysis is performed to write the axisymmetric model
information to the results files. The full tire cross-section is meshed in this model. No analysis is
needed. The axisymmetric model information is read in a subsequent run, and a full three-dimensional
model is generated by Abaqus by revolving the cross-section about the rotational symmetry axis. The
*SYMMETRIC MODEL GENERATION, REVOLVE option is again used for this purpose. The road
is defined in the full model. The three-dimensional finite element mesh of the full model is identical to
the one generated in the first analysis. However, the inflation load and concentrated load on the axle areapplied to the full model without making use of the results transfer capability.
The footprint calculations are performed with a friction coef ficient of zero in anticipation
of eventually performing a steady-state rolling analysis of the tire using the *STEADY STATE
TRANSPORT option, as explained in “Steady-state rolling analysis of a tire,” Section 3.1.2.
Since the results from the static analyses performed in this example are used in a subsequent time-
domain dynamic example, the input files contain the following features that would not ordinarily be
included for purely static analyses:
• The TRANSPORT parameter is included with the *SYMMETRIC MODEL GENERATIONoption to define streamlines in the model, which are needed by Abaqus to perform streamline
calculations during the *STEADY STATE TRANSPORT analysis in the next example problem.
The TRANSPORT parameter is not required for any analysis type except *STEADY STATE
TRANSPORT.
• The hyperelastic material that models the rubber has a *VISCOELASTIC, TIME=PRONY optionincluded. This enables us to model viscoelasticity in the steady-state transport example that follows.
As a consequence of defi
ning a time-domain viscoelastic material property, the *HYPERELASTICoption includes the LONG TERM parameter to indicate that the elastic properties defined on the
associated data lines define the long-term behavior of the rubber. In addition, all *STATIC steps
include the LONG TERM parameter to ensure that the static solutions are based upon the long-term
elastic moduli.
3.1.1–3
TIRE RESULTS TRANSFER
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
20/600
TIRE RESULTS TRANSFER
Loading
As discussed in the previous sections, the loading on the tire is applied over several steps. In the first
simulation the inflation of the tire to a pressure of 200.0 kPa is modeled using the axisymmetric tire model
(tiretransfer_axi_half.inp) with a *STATIC analysis procedure. The results from this axisymmetric
analysis are then transferred to the partial three-dimensional model (tiretransfer_symmetric.inp) in
which the footprint solution is computed in two sequential *STATIC steps. The first of these static
steps establishes the initial contact between the road and the tire by prescribing a vertical displacement
of 0.02 m on the rigid body reference node. Since this is a static analysis, it is recommended that
contact be established with a prescribed displacement, as opposed to a prescribed load, to avoid
potential convergence dif ficulties that might arise due to unbalanced forces. The prescribed boundary
condition is removed in the second static step, and a vertical load of 1.65 kN is applied to the
rigid body reference node. The 1.65 kN load in the partial three-dimensional model represents a
3.3 kN load in the full three-dimensional model. The transfer of the results from the axisymmetric
model to the partial three-dimensional model is accomplished by using the *SYMMETRIC RESULTS
TRANSFER option. Once the static footprint solution for the partial three-dimensional model has been
established, the *SYMMETRIC RESULTS TRANSFER option is used to transfer the solution to the full
three-dimensional model (tiretransfer_full.inp), where the footprint solution is brought into equilibrium
in a single *STATIC increment. The results transfer sequence is illustrated in Figure 3.1.1–5.
Boundary conditions and loads are not transferred with the *SYMMETRIC RESULTS TRANSFER
option; they must be carefully redefined in the new analysis to match the loads and boundary conditions
from the transferred solution. Due to numerical and modeling issues the element formulations for the
two-dimensional and three-dimensional elements are not identical. As a result, there may be slight
differences between the equilibrium solutions generated by the two- and three-dimensional models.
In addition, small numerical differences may occur between the symmetric and full three-dimensional
solutions because of the presence of symmetry boundary conditions in the symmetric model that arenot used in the full model. Therefore, it is advised that in a results transfer simulation an initial step be
performed where equilibrium is established between the transferred solution and loads that match the
state of the model from which the results are transferred. It is recommended that an initial *STATIC
step with the initial time increment set to the total step time be used to allow Abaqus/Standard to find
the equilibrium in one increment.
In the second simulation identical inflation and footprint steps are repeated. The only difference is
that the entire analysis is performed on the full three-dimensional model (tiretransfer_full_footprint.inp).
The full three-dimensional model is generated using the restart information from a datacheck analysisof an axisymmetric model of the full tire cross-section (tiretransfer_axi_full.inp).
Contact modeling
The default contact pair formulation in the normal direction is hard contact, which gives strict
enforcement of contact constraints. Some analyses are conducted with both hard and augmented
Lagrangian contact to demonstrate that the default penalty stiffness chosen by the code does not
affect stress results signifi
cantly. The augmented Lagrangian method is invoked by specifying the
3.1.1–4
TIRE RESULTS TRANSFER
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
21/600
TIRE RESULTS TRANSFER
AUGMENTED LAGRANGE parameter on the *SURFACE BEHAVIOR option. The hard and
augmented Lagrangian contact algorithms are described in “Contact constraint enforcement methods in
Abaqus/Standard,” Section 36.1.2 of the Abaqus Analysis User’s Manual.
Solution controls
Since the three-dimensional tire model has a small loaded area and, thus, rather localized forces, the
default averaged flux values for the convergence criteria produce very tight tolerances and cause more
iteration than is necessary for an accurate solution. To decrease the computational time required for
the analysis, the *CONTROLS option can be used to override the default values for average forces and
moments. The default controls are used in this example.
Results and discussion
The results from the first two simulations are essentially identical. The peak Mises stresses and
displacement magnitudes in the two models agree within 0.3% and 0.2%, respectively. The final
deformed shape of the tire is shown in Figure 3.1.1–6. The computational cost of each simulation is
shown in Table 3.1.1–1. The simulation performed on the full three-dimensional model takes 2.5 times
longer than the results transfer simulation, clearly demonstrating the computational advantage that can
be attained by exploiting the symmetry in the model using the *SYMMETRIC RESULTS TRANSFER option.
Input files
tiretransfer_axi_half.inp Axisymmetric model, inflation analysis (simulation 1).
tiretransfer_symmetric.inp Partial three-dimensional model, footprint analysis
(simulation 1).
tiretransfer_symmetric_auglagr.inp Partial three-dimensional model, footprint analysis using
augmented Lagrangian contact (simulation 1).
tiretransfer_full.inp Full three-dimensional model, final equilibrium analysis
(simulation 1).
tiretransfer_full_auglagr.inp Full three-dimensional model, final equilibrium analysis
using augmented Lagrangian contact (simulation 1).
tiretransfer_axi_full.inp Axisymmetric model, datacheck analysis
(simulation 2).
tiretransfer_full_footprint.inp Full three-dimensional model, complete analysis(simulation 2).
tiretransfer_symm_drum.inp Partial three-dimensional model of a tire in contact with
a rigid drum.
tiretransfer_full_drum.inp Full three-dimensional model of a tire in contact with a
rigid drum.
tiretransfer_node.inp Nodal coordinates for the axisymmetric models.
tiretransfer_axi_half_ml.inp Axisymmetric model, inflation analysis (simulation 1)
with Marlow hyperelastic model.
3.1.1–5
TIRE RESULTS TRANSFER
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
22/600
TIRE RESULTS TRANSFER
tiretransfer_symmetric_ml.inp Partial three-dimensional model, footprint analysis
(simulation 1) with Marlow hyperelastic model.
tiretransfer_full_ml.inp Full three-dimensional model, final equilibrium analysis
(simulation 1) with Marlow hyperelastic model.
Table 3.1.1–1 Comparison of normalized CPU times for the footprint analysis (normalized
with respect to the total “No results transfer” analysis).
Use results transfer
and symmetry
conditions
No results
transfer
Inflation 0.005(a) +0.040(b) 0.347(e)
Footprint 0.265(c) +0.058(d) 0.653(e)
Total 0.368 1.0
(a) axisymmetric model
(b) equilibrium step in partial three-dimensional model
(c) footprint analysis in partial three-dimensional model
(d) equilibrium step in full three-dimensional model
(e) full three-dimensional model
3.1.1–6
TIRE RESULTS TRANSFER
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
23/600
carcass
bead
sidewall
belts
tread
Figure 3.1.1–1 Tire cross-section.
1
2
3
Embedded surface elementscarrying rebar
Figure 3.1.1–2 Axisymmetric tire mesh.
3.1.1–7
TIRE RESULTS TRANSFER
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
24/600
Z
12
3
R T
Figure 3.1.1–3 Partial three-dimensional tire mesh.
Z
12
3
R T
Figure 3.1.1–4 Full three-dimensional tire mesh.
3.1.1–8
TIRE RESULTS TRANSFER
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
25/600
Z
12
3
R T
Z
12
3
R T
carcass
bead
sidewall
belts
tread
Axisymmetric model
Resultstransfer
Resultstransfer
Partial 3-D model Full 3-D model
1
2
3
Embedded surfaceelements carrying rebar
Figure 3.1.1–5 Results transfer analysis sequence.
Z
12
3
R T
Figure 3.1.1–6 Deformed three-dimensional tire (deformations scaled by a factor of 2).
3.1.1–9
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
26/600
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
27/600
3.1.2 STEADY-STATE ROLLING ANALYSIS OF A TIRE
Product: Abaqus/Standard
This example illustrates the use of the *STEADY STATE TRANSPORT option in Abaqus (“Steady-state
transport analysis,” Section 6.4.1 of the Abaqus Analysis User’s Manual) to model the steady-state dynamic
interaction between a rolling tire and a rigid surface. A steady-state transport analysis uses a moving reference
frame in which rigid body rotation is described in an Eulerian manner and the deformation is described in
a Lagrangian manner. This kinematic description converts the steady moving contact problem into a purespatially dependent simulation. Thus, the mesh need be refined only in the contact region—the steady motion
transports the material through the mesh. Frictional effects, inertia effects, and history effects in the material
can all be accounted for in a *STEADY STATE TRANSPORT analysis.
The purpose of this analysis is to obtain free rolling equilibrium solutions of a 175 SR14 tire traveling
at a ground velocity of 10.0 km/h (2.7778 m/s) at different slip angles on a flat rigid surface. The slip angle
is the angle between the direction of travel and the plane normal to the axle of the tire. Straight line rolling
occurs at a 0.0° slip angle. For comparison purposes we also consider an analysis of the tire spinning at a
fixed position on a 1.5 m diameter rigid drum. The drum rotates at an angular velocity of 3.7 rad/s, so that a point on the surface of the drum travels with an instantaneous velocity of 10.0 km/h (2.7778 m/s). Another
case presented examines the camber thrust arising from camber applied to a tire at free rolling conditions.
This also enables us to calculate a camber thrust stiffness.
An equilibrium solution for the rolling tire problem that has zero torque, T, applied around the axle isreferred to as a free rolling solution. An equilibrium solution with a nonzero torque is referred to as either a
traction or a braking solution depending upon the sense of T. Braking occurs when the angular velocity of thetire is small enough such that some or all of the contact points between the tire and the road are slipping and
the resultant torque on the tire acts in an opposite sense from the angular velocity of the free rolling solution.Similarly, traction occurs when the angular velocity of the tire is large enough such that some or all of the
contact points between the tire and the road are slipping and the resultant torque on the tire acts in the same
sense as the angular velocity of the free rolling solution. Full braking or traction occurs when all the contact
points between the tire and the road are slipping.
A wheel in free rolling, traction, or braking will spin at different angular velocities, , for the same
ground velocity, Usually the combination of and that results in free rolling is not known in advance.
Since the steady-state transport analysis capability requires that both the rotational spinning velocity, , and
the traveling ground velocity, , be prescribed, the free rolling solution must be found in an indirect manner.
One such indirect approach is illustrated in this example. An alternate approach involves controlling the
rotational spinning velocity using user subroutine UMOTION while monitoring the progress of the solution
through a second user subroutine URDFIL. The URDFIL subroutine is used to obtain an estimate of the free
rolling solution based on the values of the torque at the rim at the end of each increment. This approach is
also illustrated in this example.
A finite element analysis of this problem, together with experimental results, has been published by
Koishi et al. (1997).
3.1.2–1
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
28/600
Problem description and model definition
A description of the tire and finite element model is given in “Symmetric results transfer for a static tireanalysis,” Section 3.1.1. To take into account the effect of the skew symmetry of the actual tire in the
dynamic analysis, the steady-state rolling analysis is performed on the full three-dimensional model, also
referred to as the full model. Inertia effects are ignored since the rolling speed is low ( 10 km/h).
As stated earlier, the *STEADY STATE TRANSPORT capability in Abaqus uses a mixed
Eulerian/Lagrangian approach in which, to an observer in the moving reference frame, the material
appears to flow through a stationary mesh. The paths that the material points follow through the
mesh are referred to as streamlines and must be computed before a steady-state transport analysis can
be performed. As discussed in “Symmetric results transfer for a static tire analysis,” Section 3.1.1,the streamlines needed for the steady-state transport analyses in this example are computed using
the *SYMMETRIC MODEL GENERATION, REVOLVE option. This option generates the
three-dimensional mesh by revolving the two-dimensional tire cross-section about the symmetry axis
so that the streamlines follow the mesh lines.
The incompressible hyperelastic material used to model the rubber in this example includes a
time-domain viscoelastic component, which is enabled by the *VISCOELASTIC, TIME=PRONY
option. A simple 1-term Prony series model is used. For an incompressible material a 1-term Prony
series in Abaqus is defined by providing a single value for the shear relaxation modulus ratio, , and
its associated relaxation time, . In this example = 0.3 and = 0.1. The viscoelastic—i.e., material
history—effects are included in a *STEADY STATE TRANSPORT step unless the LONG TERM
parameter is used. See “Time domain viscoelasticity,” Section 21.7.1 of the Abaqus Analysis User’s
Manual, for a more detailed discussion of modeling time-domain viscoelasticity in Abaqus.
Loading
As discussed in “Symmetric results transfer for a static tire analysis,” Section 3.1.1, it is recommended
that the footprint analyses be obtained with a friction coef ficient of zero (so that no frictional forces
are transmitted across the contact surface). The frictional stresses for a rolling tire are very different
from the frictional stresses in a stationary tire, even if the tire is rolling at very low speed; therefore,
discontinuities may arise in the solution between the last *STATIC analysis and the first *STEADY
STATE TRANSPORT analysis. Furthermore, varying the friction coef ficient from zero at the beginning
of the steady-state transport step to its final value at the end of the steady-state transport step ensures that
the changes in frictional forces reduce with smaller load increments. This is important if Abaqus must
take a smaller load increment to overcome convergence dif ficulties while trying to obtain the steady-state
rolling solution.
Once the static footprint solution for the tire has been computed, the steady-state rolling contact
problem can be solved using the *STEADY STATE TRANSPORT option. The objective of the first
simulation in this example is to obtain the straight line, steady-state rolling solutions, including full
braking and full traction, at different spinning velocities. We also compute the straight line, free rolling
solution. In the second simulation free rolling solutions at different slip angles are computed. In the first
and second simulations material history effects are ignored by including the LONG TERM parameter on
3.1.2–2
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
29/600
the *STEADY STATE TRANSPORT steps. The third simulation repeats a portion of the straight line,
steady-state rolling analysis from the first simulation; however, material history effects are included by
omitting the LONG TERM parameter. A steady ground velocity of 10.0 km/h is maintained for all the
simulations. The objective of the fourth simulation is to obtain the free rolling solution of the tire in
contact with a 1.5 m rigid drum rotating at 3.7 rad/s.
In the first simulation (rollingtire_brake_trac.inp) the full braking solution is obtained in the first
*STEADY STATE TRANSPORT step by setting the friction coef ficient, , to its final value of 1.0 using
the *CHANGE FRICTION option and applying the translational ground velocity together with a spinning
angular velocity that will result in full braking. The *TRANSPORT VELOCITY and *MOTION options
are used for this purpose. An estimate of the angular velocity corresponding to full braking is obtained
as follows. A free rolling tire generally travels farther in one revolution than determined by its center
height, H, but less than determined by the free tire radius. In this example the free radius is 316.2 mmand the vertical deflection is approximately 20.0 mm, so 296.2 mm. Using the free radius and the
effective height, it is estimated that free rolling occurs at an angular velocity between 8.78 rad/s
and 9.38 rad/s. Smaller angular velocities would result in braking, and larger angular velocities
would result in traction. We use an angular velocity 8.0 rad/s to ensure that the solution in the first
steady-state transport step is a full braking solution (all contact points are slipping, so the magnitude of
the total frictional force across the contact surface is ).
In the second steady-state transport analysis step of the full model, the angular velocity is increasedgradually to 10.0 rad/s while the ground velocity is held constant. The solution at each load
increment is a steady-state solution to the loads acting on the structure at that instant so that a series
of steady-state solutions between full braking and full traction is obtained. This analysis provides us
with a preliminary estimate of the free rolling velocity. The second simulation (rollingtire_trac_res.inp)
performs a refined search around the first estimate of free rolling conditions.
In the third simulation (rollingtire_slipangles.inp) the free rolling solutions at different slip angles
are computed. The slip angle, , is the angle between the direction of travel and the plane normal to
the axle of the tire. In the first step the straight line, free rolling solution from the first simulation is brought into equilibrium. This step is followed by a *STEADY STATE TRANSPORT step where the
slip angle is gradually increased from 0.0° at the beginning of the step to 3.0° at the end of
the step, so a series of steady-state solutions at different slip angles is obtained. This is accomplished
by prescribing a traveling velocity vector with components and on the
*MOTION, TRANSLATION option, where 0.0° in the first steady-state transport step and 3.0°
at the end of the second steady-state transport step.
The fourth simulation (rollingtire_materialhistory.inp) includes a series of steady-state solutions
between full braking and full traction in which the material history effects are included.
The fifth simulation (rollingtire_camber.inp) analyzes the effect of camber angle on the lateral thrust
at the contact patch under free rolling conditions.
The final simulation in this example (rollingtire_drum.inp) considers a tire in contact with a rigid
rotating drum. The loading sequence is similar to the loading sequence used in the first simulation.
However, in this simulation the translational velocity of the tire is zero, and a rotational angular velocity
is applied to the reference node of the rigid drum using the *TRANSPORT VELOCITY option. Since
a prescribed load is applied to the rigid drum reference node to establish contact between the tire and
3.1.2–3
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
30/600
drum, the rotation axis of the drum is unknown prior to the analysis. Abaqus automatically updates the
rotation axis to its current position if the angular velocity is defined using the *TRANSPORT VELOCITY
option. The rotational velocity of the rigid surface can also be defined using the *MOTION, ROTATION
option. In that case the position and orientation of the axis of revolution must be defined on the data
lines in the steady-state configuration and, therefore, must be known prior to the analysis. The position
and orientation of the axis are applied at the beginning of the step and remain fixed during the step.
When the drum radius is large compared to the axle displacement, as in this example, it is a reasonable
approximation to define the axle in the original configuration without significantly affecting the accuracy
of the results.
Results and discussion
Figure 3.1.2–1 and Figure 3.1.2–2 show the reaction force parallel to the ground (referred to as rolling
resistance) and the torque, T, on the tire axle at different spinning velocities. The figures comparethe solutions obtained for a tire rolling on a flat rigid surface with those for a tire in contact with a
rotating drum. The figures show that straight line free rolling, 0.0, occurs at a spinning velocity
of approximately 9.0 rad/s. Full braking occurs at spinning velocities smaller than 8.0 rad/s, and full
traction occurs at velocities larger than 9.75 rad/s. At these spinning velocities all contact points are
slipping, and the rolling resistance reaches the limiting value
Figure 3.1.2–3 and Figure 3.1.2–4 show shear stress along the centerline of the tire surface in thefree rolling and full traction states for the case where the tire is rolling along a flat rigid surface. The
distance along the centerline is measured as an angle with respect to a plane parallel to the ground passing
through the tire axle. The dashed line is the maximum or limiting shear stress, , that can be transmitted
across the surface, where p is the contact pressure. The figures show that all contact points are slippingduring full traction. During free rolling all points stick.
A better approximation to the angular velocity that corresponds to free rolling can be made by
using the results generated by rollingtire_brake_trac.inp to refine the search about an angular velocity of
9.0 rad/s. The file rollingtire_trac_res.inp restarts the previous straight line rolling analysis from Step 3,
Increment 8 (corresponding to an angular velocity of 8.938 rad/s) and performs a refined search up to
9.04 rad/s. Figure 3.1.2–5 shows the torque, T, on the tire axle computed in the refined search, whichleads to a more precise value for the free rolling angular velocity of approximately 9.022 rad/s. This
result is used for the model where the free rolling solutions at different slip angles are computed.
Figure 3.1.2–6 shows the transverse force (force along the tire axle) measured at different slip angles.
The figure compares the steady-state transport analysis prediction with the result obtained from a pure
Lagrangian analysis. The Lagrangian solution is obtained by performing an explicit transient analysis
using Abaqus/Explicit (discussed in “Import of a steady-state rolling tire,” Section 3.1.6). With this
analysis technique a prescribed constant traveling velocity is applied to the tire, which is free to roll along
the rigid surface. Since more than one revolution is necessary to obtain a steady-state configuration, fine
meshing is required along the full circumference; hence, the Lagrangian solution is much more costly
than the steady-state solutions shown in this example. The figure shows good agreement between the
results obtained from the two analysis techniques.
Figure 3.1.2–7 compares the free rolling solutions with and without material history effects included.
The solid lines in the diagram represent the rolling resistance (force parallel to the ground along the
3.1.2–4
ROLLING TIRE
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
31/600
traveling direction); and the broken lines, the torque (normalized with respect to the free radius) on
the axle. The figure shows that free rolling occurs at a lower angular velocity when history effects are
included. The influence of material history effects on a steady-state rolling solution is discussed in detail
in “Steady-state spinning of a disk in contact with a foundation,” Section 1.5.2 of the Abaqus Benchmarks
Manual.
Figure 3.1.2–8 shows the camber thrust as a function of camber angle. The lateral force at zero
camber and zero slip is referred to as ply-steer and arises due to the asymmetry in the tire caused by the
separation of the belts by the interply distance. Discretization of the contact patch is responsible for the
non-smooth nature of the curve, and an overall camber stiffness of 44 N/degree is reasonably close to
expected levels.
Figure 3.1.2–9 shows the torque on the rim as the rotational velocity is applied with user subroutine
UMOTION , based on the free rolling velocity predicted in user subroutine URDFIL. As the torque on the
rim falls to within a user-specified tolerance of zero torque, the rotational velocity is held fixed and the
step completed. Initially, when the free rolling rotational velocity estimates are beyond a user-specified
tolerance of the current rotational velocity, only small increments of rotational velocity are applied. The
message file contains information on the estimates of free rolling velocity and the incrementation as the
solution progresses. The angular velocity thus found for free rolling conditions is 9.026 rad/s.
Acknowledgments
SIMULIA gratefully acknowledges Hankook Tire and Yokohama Rubber Company for their cooperation
in developing the steady-state transport capability used in this example. SIMULIA thanks Dr. Koishi of
Yokohama Rubber Company for supplying the geometry and material properties used in this example.
Input files
rollingtire_brake_trac.inp Three-dimensional full model for the full braking and
traction analyses.rollingtire_trac_res.inp Three-dimensional full model for the refined braking and
traction analyses.
rollingtire_slipangles.inp Three-dimensional full model for the slip angle analysis.
rollingtire_camber.inp Three-dimensional full model for the camber analysis.
rollingtire_materialhistory.inp Three-dimensional full model with material history
effects.
rollingtire_drum.inp Three-dimensional full model for the simulation of rolling
on a rigid drum.rollingtire_freeroll.inp Three-dimensional full model for the direct approach to
finding the free rolling solution.
rollingtire_freeroll.f User subroutine file used to find the free rolling solution.
Reference
• Koishi, M., K. Kabe, and M. Shiratori, “Tire Cornering Simulation using Explicit Finite ElementAnalysis Code,” 16th annual conference of the Tire Society at the University of Akron, 1997.
3.1.2–5
ROLLING TIRE
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
32/600
DrumRoad
Figure 3.1.2–1 Rolling resistance at different angular velocities.
DrumRoad
Figure 3.1.2–2 Torque at different angular velocities.
3.1.2–6
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
33/600
Lower shear limitUpper shear limit
Shear stress
Figure 3.1.2–3 Shear stress along tire center (free rolling).
Shear stressLower shear limitUpper shear limit
S h e a r s t r e s s ( M P a )
0.30
0.20
0.10
0.00
–0.10
–0.20
–0.30
70.00 80.00 90.00 100.00 110.00
Angle (degrees)
Figure 3.1.2–4 Shear stress along tire center (full traction).
3.1.2–7
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
34/600
Torque
Figure 3.1.2–5 Torque at different angular velocities (refined search).
StandardExplicit
T r a
n s v e r s e F o r c e ( k N )
2.4
2.0
1.6
1.2
0.8
0.4
0.0 0.5 1.0 1.5 2.0 2.5 3.0
Slip angle (degrees)
Figure 3.1.2–6 Transverse force as a function of slip angle.
3.1.2–8
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
35/600
Force - no convectionForce - convection includedTorque/R - no convectionTorque/R - convection included
Figure 3.1.2–7 Rolling resistance and normalized torque as
a function of angular velocity (R=0.3162 m).
Camber thrust
Figure 3.1.2–8 Camber thrust as a function of camber angle.
3.1.2–9
ROLLING TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
36/600
Torque on Rim
Figure 3.1.2–9 Torque on the rim for the direct approach
to finding the free rolling solution.
3.1.2–10
DYNAMIC TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
37/600
3.1.3 SUBSPACE-BASED STEADY-STATE DYNAMIC TIRE ANALYSIS
Product: Abaqus/Standard
This example illustrates the use of the *STEADY STATE DYNAMICS, SUBSPACE PROJECTION option
to model the frequency response of a tire about a static footprint solution.
The *STEADY STATE DYNAMICS, SUBSPACE PROJECTION option (“Subspace-based steady-state
dynamic analysis,” Section 6.3.9 of the Abaqus Analysis User’s Manual) is an analysis procedure that can be
used to calculate the steady-state dynamic response of a system subjected to harmonic excitation. It does so
by the direct solution of the steady-state dynamic equations projected onto a reduced-dimensional subspace
spanned by a set of eigenmodes of the undamped system. If the dimension of the subspace is small compared
to the dimension of the original problem (i.e., if a relatively small number of eigenmodes is used), the subspace
method can offer a very cost-effective alternative to a direct-solution steady-state analysis.
The purpose of this analysis is to obtain the frequency response of a 175 SR14 tire subjected to a harmonic
load excitation about the footprint solution discussed in “Symmetric results transfer for a static tire analysis,”
Section 3.1.1. The *SYMMETRIC RESULTS TRANSFER and *SYMMETRIC MODEL GENERATION
options are used to generate the footprint solution, which serves as the base state in the steady-state dynamics
calculations.
Problem description
A description of the tire being modeled is given in “Symmetric results transfer for a static tire analysis,”
Section 3.1.1. In this example we exploit the symmetry in the tire model and utilize the results transfer
capability in Abaqus to compute the footprint solution for the full three-dimensional model in a manner
identical to that discussed in “Symmetric results transfer for a static tire analysis,” Section 3.1.1.
Once the footprint solution has been computed, several steady-state dynamic steps are performed.
Both the *STEADY STATE DYNAMICS, DIRECT and the *STEADY STATE DYNAMICS,
SUBSPACE PROJECTION options are used. Besides being used to validate the subspace projection
results, the direct steady-state procedure allows us to demonstrate the computational advantage afforded
by the subspace projection capability in Abaqus.
Model definition
The model used in this analysis is essentially identical to that used in the first simulation discussed
in “Symmetric results transfer for a static tire analysis,” Section 3.1.1, with CGAX4H and CGAX3Helements used in the axisymmetric model and rebar in the continuum elements for the belts and
carcass. However, since no *STEADY STATE TRANSPORT steps are performed in this example,
the TRANSPORT parameter is not needed during the symmetric model generation phase. In addition,
instead of using a nonuniform discretization about the circumference, the uniform discretization shown
in Figure 3.1.3–1 is used.
The incompressible hyperelastic material used to model the rubber includes a viscoelastic
component described by a 1-term Prony series of the dimensionless shear relaxation modulus:
3.1.3–1
DYNAMIC TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
38/600
with relaxation coef ficient and relaxation time . Since the material is incompressible,the volumetric behavior is time independent. This time domain description of the material must be
written in the frequency domain to perform a *STEADY STATE DYNAMICS analysis. By applying a
Fourier transform, the expressions for the time-dependent shear modulus can be written in the frequency
domain as follows:
where is the storage modulus, is the loss modulus, and is the angular frequency. Abaqus
will perform the conversion from time domain to frequency domain automatically if the Prony series
parameters are defined with the *VISCOELASTIC, FREQUENCY=PRONY option. See “Time domain
viscoelasticity,” Section 21.7.1 of the Abaqus Analysis User’s Manual, for a more detailed discussion on
frequency domain viscoelasticity.
Loading
The loading sequence for computing the footprint solution is identical to that discussed in “Symmetric
results transfer for a static tire analysis,” Section 3.1.1, with the axisymmetric model contained in
tiredynamic_axi_half.inp, the partial three-dimensional model in tiredynamic_symmetric.inp, and
the full three-dimensional model in tiredynamic_freqresp.inp. Since the NLGEOM=YES parameter
is active for the *STATIC steps used in computing the footprint solution, the steady-state dynamicanalyses, which are linear perturbation procedures, are performed about the nonlinear deformed shape
of the footprint solution.
The first frequency response analyses of the tire are performed using the *STEADY STATE
DYNAMICS, SUBSPACE PROJECTION option. The excitation is due to a harmonic vertical load
of 200 N, which is applied to the analytical rigid surface through its reference node. The frequency
is swept from 80 Hz to 130 Hz. The rim of the tire is held fixed throughout the analysis. Prior to
the subspace analysis being performed, the eigenmodes that are used for the subspace projection are
computed in a *FREQUENCY step. In the frequency step the first 20 eigenpairs are extracted, for which the computed eigenvalues range from 50 to 185 Hz.
The accuracy of the subspace analysis can be improved by including some of the stiffness associated
with frequency-dependent material properties—i.e., viscoelasticity—in the eigenmode extraction step.
This is accomplished by using the PROPERTY EVALUATION parameter with the *FREQUENCY
option. In general, if the material response does not vary significantly over the frequency range of
interest, the PROPERTY EVALUATION parameter can be set equal to the center of the frequency span.
Otherwise, more accurate results will be obtained by running several separate frequency analyses over
3.1.3–2
DYNAMIC TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
39/600
smaller frequency ranges with appropriate settings for the PROPERTY EVALUATION parameter. In
this example a single frequency sweep is performed with PROPERTY EVALUATION=105 Hz.
The main advantage that the subspace projection method offers over mode-based techniques
(“Mode-based steady-state dynamic analysis,” Section 6.3.8 of the Abaqus Analysis User’s Manual) isthat it allows frequency-dependent material properties, such as viscoelasticity, to be included directly in
the analysis. However, there is a cost involved in assembling the projected equations, and this cost must
be taken into account when deciding between a subspace solution and a direct solution. Abaqus offers
four different parameter values that may be assigned to the SUBSPACE PROJECTION option to control
how often the projected subspace equations are recomputed. These values are ALL FREQUENCIES, in
which new projected equations are computed for every frequency in the analysis; EIGENFREQUENCY,
in which projected equations are recomputed only at the eigenfrequencies; PROPERTY CHANGE, in
which projected equations are recomputed when the stiffness and/or damping properties have changed
by a user-specified percentage; and CONSTANT, which computes the projected equations only once
at the center of the frequency range specified on the data lines of the *STEADY STATE DYNAMICS
option. Setting SUBSPACE PROJECTION=ALL FREQUENCIES is, in general, the most accurate
option; however, the computational overhead associated with recomputing the projected equations at
every frequency can significantly reduce the cost benefit of the subspace method versus a direct solution.
The SUBSPACE PROJECTION=CONSTANT option is the most inexpensive choice, but it should be
chosen only when the material properties do not depend strongly on frequency. In general, the accuracy
and cost associated with the four SUBSPACE PROJECTION parameter values are strongly problem
dependent. In this example problem the results and computational expense for all four parameter values
for SUBSPACE PROJECTION are discussed.
The results from the various subspace analyses are compared to the results from a *STEADY STATE
DYNAMICS, DIRECT analysis.
Results and discussion
Each of the subspace analyses utilizes all 20 modes extracted in the *FREQUENCY step. Figure 3.1.3–2
shows the frequency response plots of the vertical displacements of the road’s reference node for the
direct solution along with the four subspace solutions using each of the SUBSPACE PROJECTION
parameter values discussed above. Similarly, Figure 3.1.3–3 shows the frequency response plots of the
horizontal displacement of a node on the tire’s sidewall for the same five analyses. As illustrated in
Figure 3.1.3–2 and Figure 3.1.3–3, all four of the subspace projection methods yield almost identical
solutions; except for small discrepancies in the vertical displacements at 92 and 120 Hz, the subspace
projection solutions closely match the direct solution as well. Timing results shown in Table 3.1.3–1 show
that the SUBSPACE PROJECTION method results in savings in CPU time versus the direct solution.
Input files
tiredynamic_axi_half.inp Axisymmetric model, inflation analysis.
tiredynamic_symmetric.inp Partial three-dimensional model, footprint analysis.
tiredynamic_freqresp.inp Full three-dimensional model, steady-state dynamic
analyses.
3.1.3–3
DYNAMIC TIRE
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
40/600
tiredynamic_axi_half_ml.inp Axisymmetric model, inflation analysis with Marlow
hyperelastic model.
tiredynamic_symmetric_ml.inp Partial three-dimensional model, footprint analysis with
Marlow hyperelastic model.tiredynamic_freqresp_ml.inp Full three-dimensional model, steady-state dynamic
analyses with Marlow hyperelastic model.
tiretransfer_node.inp Nodal coordinates for axisymmetric model.
Table 3.1.3–1 Comparison of normalized CPU times (normalized
with respect to the DIRECT analysis) for the frequency sweep from80 Hz to 130 Hz and the *FREQUENCY step.
Normalized
CPU time
SUBSPACE PROJECTION=ALL FREQUENCIES 0.89
SUBSPACE PROJECTION=EIGENFREQUENCY 0.54
SUBSPACE PROJECTION=PROPERTY CHANGE 0.49SUBSPACE PROJECTION=CONSTANT 0.36
DIRECT 1.0
*FREQUENCY 0.073
12
3
Figure 3.1.3–1 Uniform three-dimensional tire mesh.
3.1.3–4
DYNAMIC TIRE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
41/600
Direct
All frequencies
EigenfrequenciesProperty change
Constant
Figure 3.1.3–2 Frequency response of the vertical road displacement due to a vertical
harmonic point load of 200 N applied to the reference node.
Direct
All frequenciesEigenfrequencies
Property change
Constant
Figure 3.1.3–3 Frequency response of the horizontal sidewall displacement due to a vertical
harmonic point load of 200 N applied to the reference node.
3.1.3–5
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
42/600
TIRE SUBSTRUCTURE
3 1 4 STEADY STATE DYNAMIC ANALYSIS OF A TIRE SUBSTRUCTURE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
43/600
3.1.4 STEADY-STATE DYNAMIC ANALYSIS OF A TIRE SUBSTRUCTURE
Product: Abaqus/Standard
This example illustrates the use of the substructuring capability in Abaqus (“Defining substructures,”
Section 10.1.2 of the Abaqus Analysis User’s Manual) to create a substructure from a tire under inflation and
footprint loading. Use of tire substructures is often seen in vehicle dynamic analyses where substantial cost
savings are made using substructures instead of the whole tire model. Since tires behave very nonlinearly, it
is essential that the change in response due to preloads is built into the substructure. Here the substructure
must be generated in a preloaded state. Some special considerations for creating substructures with preloads
involving contact are also discussed.
Problem description and model definition
A description of the tire model used is given in “Symmetric results transfer for a static tire analysis,”
Section 3.1.1. In this problem inflation and fooptrint preloads are applied in a series of general
analysis steps identical to “Symmetric results transfer for a static tire analysis,” Section 3.1.1. The
*SYMMETRIC MODEL GENERATION and *SYMMETRIC RESULTS TRANSFER options are
used to exploit the symmetric nature of the structure and loading. Nodes in the bead area are tied to therigid body representing the rim.
The substructure’s retained nodes include the rim node and all nodes in the footprint. To enhance
the dynamic response of the substructure, these interfacial degrees of freedom are augmented with
generalized degrees of freedom associated with the first 20 fixed interface eigenmodes. Depending on
the nature of the loading, it may be necessary to increase the number of generalized degrees of freedom
to cover a suf ficient range of frequencies. The extra cost incurred due to the addition of the extra
frequency extraction step is offset by the enhanced dynamic response of the substructure.
Loading
An inflation load of 200 kPa is applied in the axisymmetric half-tire model contained in
substructtire_axi_half.inp. This is followed by a footprint load of 1650 N applied to the three-dimensional
half-tire model given in substructtire_symmetric.inp; and, subsequently, results are transferred to
the full tire model with the complete footprint load of 3300 N. All of these steps are run with the
NLGEOM=YES parameter, so all preload effects including stress stiffening are taken into account
when the substructure is generated.To retain degrees of freedom that are involved in contact constraints at the footprint, it is necessary
to replace the contact constraints with boundary conditions. This is done once the footprint solution is
obtained by fixing the retained nodes in the deformed state and using the *MODEL CHANGE option
to remove the contact pair between the footprint patch and the road surface. Without this change,
the contact constraints produce large stiffness terms in the substructure stiffness that can produce
non-physical behavior at the usage level. The mechanical response of the substructure is unchanged
since the *BOUNDARY, FIXED option is used to hold the tire in its deformed state. These boundary
3.1.4–1
TIRE SUBSTRUCTURE
conditions on the retained degrees of freedom are then released in the *SUBSTRUCTURE GENERATE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
44/600
conditions on the retained degrees of freedom are then released in the *SUBSTRUCTURE GENERATE
step, in which they are replaced with concentrated loads. To carry out these steps, it is necessary to
obtain the list of nodes in contact with the road. Hence, the substructure is generated in a restart analysis
following the analysis with the preloads. This makes it possible to construct the list of nodes that areinvolved in contact with the road at the end of the preloading. It is necessary to specify the *MODEL
CHANGE option with the ACTIVATE parameter in the analysis prior to substructure generation to
enable the removal of the contact constraints.
To enhance the dynamic response of the substructure, several restrained eigenmodes are included
as generalized degrees of freedom. These restrained eigenmodes are obtained from a *FREQUENCY
step with all the retained degrees of freedom restrained. In this example the first 20 eigenmodes,
corresponding to a frequency range of 50 to 134 Hz, are computed. With 67 nodes in the footprint, one
rim node with six degrees of freedom, and 20 generalized degrees of freedom, the substructure has 227degrees of freedom.
At the usage level the nodes that form the footprint patch in the tire model are restrained to a single
node. The steady-state response of the substructure to harmonic footprint loading is analyzed over a
range of frequencies from 40 to 130 Hz.
Results and discussion
A steady-state dynamic analysis of the substructure with *STEADY STATE DYNAMICS, DIRECT isrelatively inexpensive compared to running a similar analysis with the entire tire model. The results for
the frequency sweep are shown in Figure 3.1.4–1, which compares the response of the substructure to
the response of the entire tire model. All resonances in the tire model are captured by the substructure.
This result shows that, although the static response of the tire is used to condense the stiffness and the
mass for the retained degrees of freedom, relatively few generalized degrees of freedom can adequately
enhance the dynamic response of the substructure. However, the associated expense of calculating the
restrained eigenmodes must be taken into account when considering the total cost.
The tire model used for comparison in this example is the same as the model used in “Symmetricresults transfer for a static tire analysis,” Section 3.1.1, with one difference. Friction is activated in a
step prior to the *STEADY STATE DYNAMICS step to activate constraints in the contact tangential
direction on nodes in the footprint so that constraints equivalent to those applied on the footprint nodes
in the substructure model are produced.
Input files
substructtire_axi_half.inp Axisymmetric model, inflation analysis.substructtire_symmetric.inp Partial three-dimensional model, footprint analysis.
substructtire_full.inp Full three-dimensional model, final equilibrium analysis.
substructtire_generate.inp Substructure generation analysis.
substructtire_dynamic.inp Usage level model with steady-state dynamics analysis.
3.1.4–2
TIRE SUBSTRUCTURE
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
45/600
Figure 3.1.4–1 Vertical response of the road node due to unit vertical harmonic load.
3.1.4–3
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
46/600
TIRE-AIR ACOUSTIC ANALYSIS
3.1.5 COUPLED ACOUSTIC-STRUCTURAL ANALYSIS OF A TIRE FILLED WITH AIR
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
47/600
Product: Abaqus/Standard
The air cavity resonance in a tire is often a significant contributor to the vehicle interior noise, particularly
when the resonance of the tire couples with the cavity resonance. The purpose of this example is to study
the acoustic response of a tire and air cavity subjected to an inflation pressure and footprint load. This
example further demonstrates how the *ADAPTIVE MESH option can be used to update an acoustic mesh
when structural deformation causes significant changes to the geometry of the acoustic domain. The effect
of rolling motion is ignored; however, the rolling speed can have a significant influence on the coupled
acoustic-structural response. This effect is investigated in detail in “Dynamic analysis of an air-filled tirewith rolling transport effects,” Section 3.1.9.
The acoustic elements in Abaqus model only small-strain dilatational behavior through pressure degrees
of freedom and, therefore, cannot model the deformation of the fluid when the bounding structure undergoes
large deformation. Abaqus solves the problem of computing the current configuration of the acoustic
domain by periodically creating a new acoustic mesh. The new mesh uses the same topology (elements
and connectivity) throughout the simulation, but the nodal locations are adjusted periodically so that the
deformation of the structural-acoustic boundary does not lead to severe distortion of the acoustic elements.
The calculation of the updated nodal locations is based on adaptive mesh smoothing.
Problem description
A detailed description of the tire model is provided in “Symmetric results transfer for a static tire
analysis,” Section 3.1.1. We model the rubber as an incompressible hyperelastic material and include
damping in the structure by specifying a 1-term Prony series viscoelastic material model with a
relaxation modulus of 0.3 and relaxation time of 0.1 s. We define the model in the frequency domain
using the *VISCOELASTIC, FREQUENCY=PRONY option since we want to include the dampingeffects in a steady-state dynamic simulation.
The air cavity in the model is defined as the space enclosed between the interior surface of the tire
and a cylindrical surface of the same diameter as the diameter of the bead. A segment of the tire is shown
in Figure 3.1.5–1. The values of the bulk modulus and the density of air are taken to be 426 kPa and
3.6 kg/m3 , respectively, and represent the properties of air at the tire inflation pressure.
The simulation assumes that both the road and rim are rigid. We further assume that the contact
between the road and the tire is frictionless during the preloading analyses. However, we use a nonzero
friction coef ficient in the subsequent coupled acoustic-structural analyses.
Model definition
We use a tire model that is identical to that used in the simulation described in “Symmetric results transfer
for a static tire analysis,” Section 3.1.1. The air cavity is discretized using linear acoustic elements and
is coupled to the structural mesh using the *TIE option with the slave surface defined on the acoustic
domain. We model the rigid rim by applying fixed boundary conditions to the nodes on the bead of the
3.1.5–1
TIRE-AIR ACOUSTIC ANALYSIS
tire, while the interaction between the air cavity and rim is modeled by a traction-free surface; i.e., no
-
8/15/2019 Abaqus 6.11, Example Problems Manual, vol. 2
48/600
boundary conditions are prescribed on the surface.
The *SYMMETRIC MODEL GENERATION and *SYMMETRIC RESULTS TRANSFER
options, together with a *STATIC analysis procedure, are used to generate the preloading solution,which serves as the base state in the subsequent coupled acoustic-structural analyses.
In the first coupled analysis we compute the eigenvalues of the tire and air cavity system. This
analysis is followed by a direct-solution and a subspace-based steady-state dynamic analysis in which
we obtain the response of the tire-air system subjected to harmonic excitation of the spindle.
A coupled structural-acoustic substructure analysis is performed as well. Frequency-dependent
viscoelastic material properties are evaluated at 230 Hz, which is the middle of the frequency range of
the steady-state dynamic analysis. The viscoelastic material contributions to the stiffness and st