abac formula 5.5 22kw
DESCRIPTION
Aiir compressor manualTRANSCRIPT
Rotary screw compressorskW 5,5–7,5–11–15–18,5–22
bar 8–10–13–15
FORMULA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Air end TriAB 51/TriAB 69
Electric motor IP55
MC2 controller
Star Delta starter IP54
Refrigerant air dryer with pre-filter and final filter (optional)
Frequency Inverter (optional)
Electric fan
Intake filter
Oil separator filter
Oil filter
Intake valve
Pre-filter panel
Air/oil cooler
Automatic belt tensioner
Minimum pressureand check valve
11 7109 8 131
In the FORMULA.E version, the compressed air provided is dried and filtered througha refrigeration air dryer with R134A ecological gas and by two air treatment filters. The airdryer package is installed in a separate area of the compressor cabinet but it is controlledby the compressors microprocessor based controller which regulates its operating cyclesmatching the compressed air demands of the system, providing constant monitoring andcontrol of the dew point. The air treatment filters eliminate all polluting particles which occurnormally in industrial conditions along with water droplets and any lubricant particles resultingfrom the compression cycle:
The ceramic pre-filter intercepts solid particles and emulsions up to 5 micron;A further desoiling filter intercepts solid and liquid particles up to 1 micron.
The compressed air at outlet is thus clean, environmentally friendly and suitable for use inpneumatic applications throughout industry. A condensate drain controlled by the compressormicroprocessor provides for the single discharge of all the condensate. The discharge timeas well as intervals can be customized by the end-user.
Compressed air treatment
1415
6 43
2
FORMULA
12
One of the most important factors in achievingincreased performance and a longer service life withall rotary screw compressors is the quality of the inletair. With this in mind, the FORMULA range featuresa two stage air filtration system: air enters througha pre-filter panel, which helps to keep the internalcomponents of the compressor clean as wellas maintaining optimum cooling efficiency.The second stage of filtration occurs as the air flowsthrough a highly efficient air suction filter, this ensuresthat the air entering the compressor element iscleaned efficiently, thus providing a considerablylonger service life to the whole compressor.
The ABAC screw compressors are fitted with theunique TriAB air ends that are designed and builtexclusively at the ABAC factories, which arecertified to ISO 9001. The highest quality standards arestrictly adhered to throughout the manufacturingprocess ensuring constantly high quality.
Highly developed, asymmetric rotor profiles withprecision ground 5/6 lobe configuration,provides higher compressed air output with lowerpower consumption.Each rotor is fitted with 3 oversized high precisionbearings allowing a longer air end life.Shaft seal with a 3 lip design providing a total protection from oil and other contaminants.Toothed safety washers and special locking nut ensure that the rotor tolerances are set throughoutthe life of the unit for improved reliability.
Latest generation microprocessor.Easy to use, with a backlit display, extended messages,multi-language, with special functions and/or emergencysignaling led’s, the MC2 controller also features:
Possible hardware expansion.Possibility to interface with other compressors usingthe optional interface card.Daily and/or weekly operational programming of up to4 compressors allowing start/stop switchingand sequencing control.Remote ControlAuto-restartProgrammed routine maintenance.Diagnostic functions with fault log.
MC2 Controller
Clean inlet air
TriAB Air endsPATENTED
In the design of the FORMULA series agood deal of consideration was givento providing accessibility and easeof maintenance, all standard servicecomponents have been positionedat the front of the compressor thusallowing immediate accessibility by simplyremoving the front panel.
The quick and easy access to the routinemaintenance components allowsminimum compressor downtime and alsoa drastic reduction in service time and thus lower costs.
Providing high quality compressed air inLine with key environmental objectives hasbeen given a lot of attention during thedevelopment of the FORMULA range.Thanks to the unique internal design ofThe vertical air/oil separator vessel andthe high efficiency air/oil separatorcartridge, very clean compressed air isprovided.Residual oil content within the deliveredcompressed air is less than 3 mg. percubic metre. Furthermore, an oversizedand extremely robust stainless steel deliveryhose allows for very low load losses.
Accessibility Oil filtrationLow maintenancetimes and costs
The constant air flow generated by theelectric fan provides very efficient coolingeven during continuous use and in highambient temperatures. This combined withthe high efficiency air/oil cooler allowsoperating temperatures to be verylow. The lower operating temperaturesresult in longer life to both componentsand to the lubricant.
The entire FORMULA range featuresan automatic belts tensioning systemensuring longer life to the drive belts,preventing slipping and allowing for simplequick replacement.
All drive components such as the mainmotor and the air end etc. are mountedon a sturdy baseplate which is supportedby anti vibration-dampers absorbingvibration and any resulting noise.The sound absorbent cabinet panels finallyensure the lowest possible noise levels.
Air cooling
Silence
Automatic belt adjustment
FORMULA.I VARIABLE SPEEDtechnical charactheristics
8 0,7810 0,6913 0,5415 0,408 1,20
10 1,0413 0,8015 0,648 1,65
10 1,4013 1,1715 0,958 2,01
10 1,7213 1,4915 1,168 2,32
10 1,9313 1,6215 1,308 2,82
10 2,5013 2,1015 1,648 3,32
10 2,9513 2,5015 1,93 Te
chn
ica
l da
ta m
ay
vary
with
out
no
tice
FORMULA Technical charactheristics
FORMULA 5,5
FORMULA 7,5
FORMULA 11
FORMULA 15/51
FORMULA 15/69
FORMULA 18,5
FORMULA 22
m3minbar
PressureModel Capacity ISO 1217 Motor PowerKw
Air end type
Dimensions mmLenght x Width x Height
WeightKg
5,5 TriAB 51 1030 x 615 x 1045 270
7,5 TriAB 51 1030 x 615 x 1045 275
11 TriAB 51 1030 x 615 x 1045 275
15 TriAB 51 1030 x 615 x 1045 286
15 TriAB 69 1500 x 660 x 1170 400
18,5 TriAB 69 1500 x 660 x 1170 410
22 TriAB 69 1500 x 660 x 1170 420
6 - 13 0,44 1,65
6 - 13 0,92 3,32
FORMULA 11
FORMULA 22
m3min
Min Max
bar
PressureModel Capacity* ISO 1217 Motor PowerKw
Air endtype
Dimensions mmLenght x Width x Height
WeightKg
11 TriAB 51 1030 x 615 x 1045 300
22 TriAB 69 1500 x 660 x 1170 440
*Capacity referred at 8 bar
Nic
olet
to D
esig
n A
ssoc
iati
- Fo
toni
co
Providing the highest levels of performance for the entirelife of the compressor is our main objective. The use ofGENUINE ABAC SPARE PARTS garantees the correct and safefunction of the FORMULA screw compressor, maintaining over time continuous performance.Demand GENUINE ABAC SPARE PARTS from your localdistributor.
CODE DESCRIPTION
8234149 Complete filters kit FORMULA 5,5-7,5
8234150 Complete filters kit FORMULA 11-15/51
8234151 Complete filters kit FORMULA 15/69-18,5 -22
GENUINE ABAC spare parts
Abac UK LTDUnit 11, Granville WayChaucer Industrial Park-BicesterOxfordshire OX26 4JTTel. +44(0)1869 326226Fax +44(0)1869 326216e-mail: [email protected]: www.abac.co.uk
CUSTOMER SERVICEA full product support package is available to all of our customers throughout the world.Qualified technical advice and support is provided in strategic locations and in all majorcountries. Advice on installation, selection, additional equipment, maintenancemanagement and environmental issues are available on request.
Tel. +44(0)1869 326226 Fax: +44(0)1869 326216 e-mail: [email protected]
Distributor
ABAC air compressors are manufactured in compliance with:98/37 CE machinery Directive; 87/404 CE simple pressure vessels Directive; 73/23 CE low voltage Directive;89/336 CE for electromagnetic compatibility;2000/14 CE for noise level.
cod.
90
36
33
9 P
rint
ing
03
/2
00
4