a11 low temperature cutout control a19 high range ... · valve bodies: commercial--3/8",...

OKLAHOMA CITY • (405) 239-7301 TULSA • (918) 249-1918 (800) 289-3331 • FAX: (405) 232-5438 (800) 955-1918 • FAX: (918) 249-9014 163

4

______________________JOHNSON CONTROLS

Order No. Switch Action Range Fo Differential Bulb and Capillary Range Adjuster Max. Bulb Temp.A19AAB10 Spst, Open High,

Oven Thermostat200-550oF 10oF 3/16" X 6"copper,

8' cap.Convertible 620oF

Motor Ratings VAC 120 208 240AC Full Load Amp 16 9.2 8AC Locked Rotor Amp 96 55.2 48

A19 HIGH RANGE TEMPERATURE CONTROLThe A19 Series are single stage temperature controls that incorporate liquid filled sensing elements.

johnson A19 high Temp 6/12/2008

Order No.Switch Action Range Differential

Bulb and Capillary

Bulb well No. (order

separately)

Max. Bulb

Temp.

A19ABC24 Spdt --30 - 100oF 3 - 12oF 3/8" X 4"; 6' cap. WEL14A-602R 140oF

Motor Ratin 120 208 240AC Full Load 16 9.2 8AC Locked R 96 55.2 48

A19 REMOTE BULB CONTROLThe A19 series are single-stage temperature controls that incorporate liquid filled sensing elements. A19's are suitable for temperature control in heating, ventilating , and refrigeration.

johnson A19 remote bulb 6/12/2008

Order No. Model No.Main

ContactsAuxillary Contacts Range Diff. Fo

Bulb and Capillary

Bulb Temp

Fo Range Adjuster

A70HA11 A70HA-1C Open Low Close Low 15 - 55oF Manual Reset 20" of 1/8" OD Tubing

400oF Screwdriver Slot

Switch Action

1 Low cutout stop is set and sealed at 35oF. Control responds only to the lowest temperature along any one foot of entire 20' element or bellows cup.

The A70 Series are heavy duty temperature controls

A70 SERIES 4-WIRE, 2 CIRCUIT TEMPERATURE CONTROLS

johnson a70 temp control 6/12/2008

Order No.Switch Action

Range ºF Diff ºF

Range Adjuster

A11A1

SPST Open Low 35-45

Manual Reset

Screwdriver Slot

Bulb and Capillary

20 ft. of 1/8" O.D. Tubing, 4 ft. Cap.

The A11 reacts to the coldest 18" section of the controls sensing element. It is suitable for monitoring the face temperature of hot water coils for freeze protection.

A11 LOW TEMPERATURE CUTOUT CONTROL

Order No. Model No. Description Set Point Range Differential Input VoltageA319ABC2401 A319ABC-24-01 Field-selectable mode jumpers work

to control either heating or cooling equipment with LED indication of relay energization status.

--20 - 100 Fo 1 - 30 FO 120 or 208/240 Vac

Special order A319ABC-12-01 Field-selectable mode jumpers work to control either heating or cooling equipment with LED indication of relay energization status.

100-200oF. 1-30oF. 120 or 208/240 Vac

A319 ELECTRONIC TEMPERATURE CONTROLThe A319 Series is a line voltage single-stage electronic temperature control with single-pole, double-throw relay output and LED indication. The A319 is designed with heating or cooling modes of operation, adjustable differential, and an interchangeable temperature sensor. The A319 couples electronic accuracy with remote sensing capability in a NEMA 1 high-impact plastic enclosure suitable for surface or DIN rail mounting.

johnson a319 electronic control 6/12/2008

164 www.federalcorp.com

4

Order No.Switch Action

Range Pressure

Differential psi

Switch Differential

Pressure Connections

Bellows Material

P74FA5 SPDT8-60

Adjustable 1.5 Fixed 1/4" FNPT Brass

P74 DIFFERENTIAL PRESSURE CONTROLThe P74 measures the pressure difference between two sources. A change in differential pressure will cause corrective action of the supplementary control equipment.

JOHNSON CONTROLS_______________________F63 SERIES LIQUID LEVEL FLOAT SWITCHESCONTROL FOR CLOSED TANKS & SUMPSSPECIFICATIONSMinimum tank diameter: 9" Pipe Connection: 1" NPT brass

Order No. Switch Action Type of Enclosure Max. MinMax. Ambient

Temp.Max. Liquid

PressureMotor Ratings @

120 Vac

F63AC1 spdt General Purpose 250oF 32oF 180oF 100 psig 16ANote: Not for use with hazardous fluids or in hazardous atmosphere.

Liquid Temp.

johnson f63 float switch 6/12/2008

Order No. Model No.100%

LockoutDamper

PlugG600AX1 G600AX-1 No YesG670AW1 G670AW-1 No No

G600/670 SERIES IGNITION CONTROL AND VALVE REPLACEMENT PARTS

Remarks24 Vac, Non-100% Lockout, Terminal board wiring24 Vac, Non-100% Lockout, Replacement for Non-100% Lockout G67's.

FOR REPLACEMENT OF G60, G65, G67, AND CSA CONTROLS

Johnson G6XXX ignition 6/12/2008

Order No. DescriptionG779LHA1 Prepurge period less than 1 second. Pilot burners with flow rates of

1,500 BTU/hr or less. Operates with or without vent dampers.

G779 UNIVERSAL REPLACEMENT INTERMITTENT PILOT IGNITION CONTROLThe G779 replaces many existing intermittent pilot controls made by various manufacturers. It is a safety control designed for indirect burner ignition and supervision. The G779 can be used with all gas-fired appliances with a maximum firing rate of 400,000 BTU/hr.

johnson g779 univ ign 6/12/2008

K16 "HUSKY" REPLACEMENT THERMOCOUPLES

Order No. Model No. Length Use With mV RangeSpecial Order K16BT24 24" Series 300 and 500 25-35 mVK16BT36 K16BT36 36" Series 300 and 500 25-35 mVK16WT48 K16WT48 48" Baso, Basoid, Basotrol 25-35 mVSpecial Order K16WT60 60" Baso, Basoid, Basotrol 25-35 mVSpecial Order K16WT72 72" Baso, Basoid, Basotrol 25-35 mVReplaces: Baso 17D, 50, 58D, 87D, 88D, 97D, 107D and K15DA thermocouples. Also fits Baso 19119 pilot burner

This heavy-duty, high performance thermocouple provides high output for residential, commercial and industrial applications. Packed with adapters to effect the necessary replacement.

johnson k16 thermocouples 6/12/2008

P70 SERIES SINGLE POLE HIGH PRESSURE CONTROLS

Order No.Switch Action Range Differential

Pressure Connector

Limited Knob Adjustment

Max. Bellows Pressure

Electrical Rating @ 120 Vac

P70AA118 Close High, Open Low

100-400 psi

Min. 35 psi Max. 200 psi

36" Cap. With 1/4" Flare Nut

None 500 psig 20A

HEAD PRESSURE FAN CYCLING

johnson p70 series high 6/12/2008


4

_______________________JOHNSON CONTROLSWEL SERIES BULB WELLSFOR REMOTE BULB THERMOSTATS AND WATER VALVES

Order No. Model No. Fig. A B CInside

DOutside

E Connector TubeMax.

Temp.Max

Pressure Plating

WEL11A601R1 WEL11A-601R 2 2 3/8" 2 5/16" 0.3 N/A 1/2" Brass Copper 250oF. 300 psig N/AWEL14A602R2 WEL14A-602R 3 4 15/16"1 13/16" 0.43 N/A 1/2" Brass Copper 250oF. 300 psig Brite-Dip

2 With phenolic bushing; .125" slot

Pipe Thread Material

1 With phenolic bushing; .093" slot

Dimensions

johnson WEL series BULB WELLS 6/12/2008

V46 SERIES PRESSURE ACTUATED VALVESWATER REGULATING

SPECIFICATIONSMax. water supply pressure: 150 psiMax. bellows pressure: 230 psg for R12 models, 320 psg for R-22 and all range models.Max. water supply temp.: 170oFValve bodies: Commercial--3/8", 1/2", 3/4" cast brass; 1" and larger cast iron with special finish

Order No. Model No. Pipe SizeInlet and

Outlet ServiceOpening Point

RangePressure

Element Style Seat Repair KitReplacement Power

ElementsV46AA1 V46AA-1C 3/8" NPT Threaded All-range 70-260 psig 13 STT14A-600R SEP91A-600R and

SEC37A-601R1

V46AB1 V46AB-1C 1/2" NPT Threaded All-range 70-260 psig 13 STT15A-602R SEP91A-602R and SEC37A-602R1

V46AC1 V46AC-1C 3/4" NPT Threaded All-range 70-260 psig 13 STT16A-601R SEP91A-601R and SEC37A-602R1

1 Replacement element supplied with 1/4" male SAE connector. Order SEC37A capillary kit with 2 flare nuts separately, if needed.

Modulating valve for closed or open systems. Opens on pressure increase to regulate flow of water or glycol to a water cooled condensers.

johnson v46 series valves 6/12/2008

JOHNSON CONTROLS_______________________

V47 SERIES TEMPERATURE ACTUATED MODULATING VALVES

SPECIFICATIONSMax. water supply pressure: 150 psi Capillary Length: 6 feet Nylon ArmorMax. water supply temp.: 170oFMax. bulb temperature: 20oF above maximum range

Order No. Model No. Pipe Size

Range (Opening

Point) Bulb Size

Standard By-Pass

Orifice Dia. Seat Repair Kit

Replacement Sensing Element

Bulb Well No. Order

Separately

V47AB3 V47AB-3C 1/2" NPT 115-180oF.11/16" X 3 1/4 1/16" STT15A-602R SET29A-624R WEL18A-602RV47AB5 V47AB-5C 1/2" NPT 75-135oF. 11/16" X 10" 1/16" STT16A-602R SET29A-602R WEL17A-600RV47AC3 V47AC-3C 3/4" NPT 115-180oF.11/16 X 3 1/4 1/16" STT16A-601R SET29A-626R WEL18A-602R

The V47 is a temperature actuated modulating valve that regulates the flow of water or glycol to maintain a desired temperature. Valve action is open on temperature increase.

johnson v47 series valves 6/12/2008


4

PARTS AND ACCESSORIES

Order No. Model No. DescriptionApplication (Volume)

T4002124 T-4002-124 BRACKET, SURFACE MTNG ALL T-STATS High

T-4000 SERIES PNEUMATIC ROOM THERMOSTATOrder No. Action Mounting Dial

SINGLE TEMPERATURE, PROPORTIONAL, HIGH VOLUME OUTPUTT40022011 Direct Horizontal 55-85o F.T40022021 Reverse Horizontal 55-85o F.T40022031 Direct Vertical 55-85o F.T40022041 Reverse Vertical 55-85o F.1. Order cover and mounting bracket separately.

johnson T4000 THERMOSTAT 6/12/2008

Order No. Model No. Action Mounting IncludesT41001 T4100-1 Direct Vertical Cover and mounting plate

T-4100 LOW VOLUME OUTPUT THERMOSTATThe T4100 is a pneumatic, single temperature thermostat that is low volume and requires only one air connection.

johnson pneumtc t4100 6/12/2008

JOHNSON CONTROLS______________________

Order No. Model No.

A350AA1C A350AA-1C

A350AA2C A350AA-2C

D350AA1C D350AA-1C

S350AA1C S350AA-1C

BKT2871R BKT287-1RBKT2872R Special OrderPLT3441R PLT344-1RWEL11A601R WEL11A-601RY350R1C Y350R-1C

A99BC25C A99BC25C

ACCESSORIES

System 350TM is a modular electronic control series consisting of a wide variety of on/off temperature, humidity, and pressure applications, as well as proportional temperature and temperature reset. The basic system consists of a control module, which accepts add-on stage, LCD display, and transformer modules. A variety of temperature, pressure, and humidity sensors are also available. Hundreds of different control systems can be configured using combination of the controls and their add-on accessories. Five-pin connectors eliminate wiring errors. The modules can be DIN rail or surface mounted.

SYSTEM 350TM ELECTRONIC MODULAR CONTROLS

Temperature Display Module; Display Range: --30-250oF.Temperature Stage Module; Offset Range 1-30oF., Differential 1-30oF.

Temperature Controller, spdt, Temperature Range, 90-250oF., Differential 1-30oF.Temperature Controller, spdt, Temperature Range:--30-130oF.,Differential: 1-30oF.

Description

Sensor with 9" leads; 1/4" diameter bulb X 1.75" - replaces SET189A-600R

Power module. 120/240 to 24Vac transformer, 10VA. For use with A350, A350P, A350R, P352, R353/S353 and W351 modules.

DIN rail, 12"DIN rail, 36"DIN rail end plate1/2" copper immersion well

Johnson system 350 6/12/2008

JOHNSON PNEUMATIC______________________

Order No. Size RangeR13015 3/8" 2-30

Air Pressure Reducing Valve with gauge port. Fitting Size 3/8 in. NPT. Flow capacity 20 SCFM (9.4 L/s). Replacement for the discontinued R-130-14.

R130 AIR PRESSURE REDUCING VALVE

JOHNSON r130 AIR PRESS REDU VALV 6/12/2008


4

______________________JOHNSON PNEUMATIC

Order No. Model No.

T47522011 T4752-201T47562011 T4756-201 Dual dial, direct acting at 15 psi and reverse acting at 20 psi.

Single dial, direct acting at 15 psi and reverse acting at 20 psi

1. Order cover and mounting bracket separately.

T-475X PNEUMATIC HEAT/COOL THERMOSTATThe T-475X series thermostats are high volume output and provide automatic changeover between heating and cooling when supply pressure changes from 15psi to 20psi. They are two pipe thermostats.

Description

johnson pneumatc t475X 6/12/2008

T SERIES ROOM THERMOSTAT COVERSOrder No. Description Mounting Set Point Thermometer

T40002139 Beige plastic with logo Horizontal Concealed NoT40002141 Beige plastic with logo Horizontal Window NoT40002142 Beige plastic with logo Horizontal Window YesT40002144 Beige plastic with logo Vertical Concealed NoT40002146 Beige plastic with logo Vertical Window Yes

johnson T SERIES THERMOSTAT COVERS 7/24/2008

T-5210 SERIES PNEUMATIC TEMPERATURE TRANSMITTERS

Order No.Operating Temperature

Range Element Style

T52101004 40-240o F. Copper bulb with 5 1/2" copper capillaryT52101114 0-100o F. Copper bulb with 4' copper capillary

The T-5210 Pneumatic Temperature Transmitter is designed to measure a temperature and convert this measurement to an air pressure signal that is transmitted to a pneumatic receiver, controller, or receiver-indicator. When used with a Dewcel® (purchased locally), the T-5210 can also be used as a dew point transmitter. The T-5210 operates in any position and should be mounted on a rigid flat surface. The instrument requires a .007 in. restricted supply.

johnson t5210 SERIES transmitters 6/12/2008

JOHNSON CONTROLS______________________


T-5800 SERIES PNEUMATIC RECEIVER-CONTROLLERS

SPECIFICATIONSAction: Direct or reversing acting; field selectable Body: Black Noryl® thermoplasticGain: Adj. From 0.5:1-15:1 Cover: 170oF Clear acrylic thermoplasticSupply pressure: 18-22 psig Mounting: SurfaceOutput capacity: 1000 scim

Order No. Description Control Mode Air ConsumptionT58003 Dual input receiver-controller Proportional 60 scim

The T-5800 Series Receiver-Controllers are designed for use with remote temperature, humidity, or pressure transmitters (connected to the controlled variable “CV” input) to provide precise control of pneumatic devices. These receiver-controllers are capable of providing restricted supply air to low volume remote transmitters, thus requiring only one air line connection between the two instruments. In addition, the “CV” input can accept the transmitted output of any pneumatic device which has a calibrated output of 3 to 15 psig (21 to 105 kPa), such as a process transmitter.

johnson t5800 SERIES recv-contl 6/12/2008

T-8000 BULB ELEMENT PNEUMATIC THERMOSTAT

Order No. Element Dial (Two-Sided) Capillary Length

T80001 Bulb -10 - 124oF./110 - 244oF. 4 feetT80003 Bulb -10 - 124oF./110 - 244oF. 15 feet

The T-8000 Bulb Element Thermostat provides proportional, direct action, or reverse action temperature control. The T-8000 is designed for applications which require the sensing element to be located where extreme conditions do not permit controller mounting or where operational adjustments to the controller would be inconvenient. This relay-type instrument is ideally suited for installations requiring the controller to be mounted on a local control panel.

johnson T8000 THERMOSTAT 6/12/2008

Order No.SHL10A603R

T8001605

ACCESSORIES FOR T8000Description

Weather shield for T8000 and T5XXX sensing bulbs6 1/2" brass well for 1/4" diameter bulb


4

Order No. Model No. Size Cv Spring Range Normal positionVG7241ET-8 VG7241ET+3008B0 1/2" NPT 1.8 3-6# OpenVG7241LT-12 VG7241LT+3008B0 3/4" NPT 7.3 3-6# OpenVG7241NT010 VG7241NT+3008B0 1" 11.6 3-6# OpenVG72441ET-8 VG7441ET+3008E0 1/2" NPT 1.8 9-13# ClosedVG7441GT-8 VG7441GT+3008E0 1/2" NPT 4.6 9-13# ClosedVG7441NT010 VG7441NT+3008E0 1" NPT 11.6 9-13# Closed

VG7X41 VALVES W/PNEUMATIC ACTUATORSThe VG7X41 series valves are brass control valves with brass trim and flow characteristics. They are equal percentage and come with the V-3000 pneumatic actuator factory mounted. They are two way valves with standard threaded stems.

johnson pneu vg7x41 valves 6/12/2008

Order No. Model No. DescriptionV37546009 V-3754-6009 Spring kit; 9-13#, for valves with 1/2" strokeV37546010 V-3754-6010 Spring kit; 3-6#, for valves with 1/2" strokeV39746008 V-3974-6008 Spring kit; 4-8# for valves with 1/2" strokeV9999608 V-9999-608 Ring packing kit for valves with 1/4" stem

VALVE PARTS

johnson valve parts 6/12/2008

Order No. Model No. Size Cv Spring RangeVG7842ET-8 VG7842ET-3008D0 1/2" NPT 1.8 4-8#VG7842LT-12 VG7842LT+3008E0 3/4" NPT 7.3 9-13#VG7842NT010 VG7842NT+3008E0 1" NPT 11.6 9-13#VG7842PT012 VG7842PT+3008E0 1 1/4" NPT 18.5 9-13#VG7842RT015 VG7842RT+3008E0 1 1/2" NPT 28.9 9-13#

VG7842 VALVES W/PNEUMATIC ACTUATORSThe VG7842 series bronze control valves have brass linear trim and flow characteristics. They are three-way mixing valves and come with the V-3000 pneumatic actuator factory mounted. The stem type is standard threaded.

johnson vg7842 valves 6/12/2008


V-3000 SERIES PNEUMATIC VALVE ACTUATORS

Order No. Model No. Style Description

V30001 V3000-1 Exposed1 For installation in a protected location, less springs.Special Order V3000-2 Enclosed For installation in a location where the actuator would be subjected

to tampering.

V30006000

1. A V-9502 Valve Positioner can be ordered separately for use on the exposed model only in applications where sequential operation is desired or additional positioning power is necessary. The V-9502 Valve Positioner can also be factory mounted.

Designed to accurately position steam or water valve modulating plugs in response to a pneumatic signal from a controller

V3000-1 REPLACEMENT DIAPHRAGM

johnson v3000 valve actuator 6/17/2008

Order No. Voltage

V11HAA100110/120 V, 50/60 Hz

Operating Presssure: 0-25 psig

Description

1/4" Barb in Common and N.C.Ports; N.O. Port is 1/8" NPT

V11 3-WAY SOLENOID AIR VALVEThe V11 is used where an electrical circuit operates a pneumatic control device.Maximum Pressure Rating: 30 psig


4

JOHNSON PNEUMATIC PARTS & ACCESSORIES

Order No. Model No. DescriptionA4000604 A-4000-604 Filter cartridge, 20 scfm, for Auto-DrainA4000610 A-4000-604 Replacement auto-drain trapA40001037 A-4000-137 1/4" barb in-line air filterR13015 R-130-15 Pressure regulatorR37102005 R-3710-2005 1/4" Straight barb restrictor; red, .005R37102007 R-3710-2007 1/4" Straight barb restrictor, aqua, .007R37103007 R-3710-3007 1/4" Tee barb restrictor, aqua, .007T4000119 T-4000-119 Adjustment tool

PNEUMATIC ACCESSORIES

johnson pneu accessories 7/24/2008


GAS APPLIANCE REGULATORSOrder No. Model No. Size Range (In. WC) Max Inlet PSI

RV SERIES RUBBER SEAT POPPET DESIGN. (Main Burner & Pilot Applications)RV12LT-2 RV12LT 1/8" 3-5 1/2RV20L-4 RV20L 1/4" 3-5 2RV20L-6 RV20L 3/8" 3-5 1/2RV48L-8 RV48L 1/2" 3-6 1/2STRAIGHT-THRU FLOW DESIGN. (Main Burner Applications Only)RV53-12 RV53 3/4" 3-6 1/2RV53010 RV53 1" 3-6 1/2RV61010 RV61 1" 5-12 1RV61012 RV61 1-1/4" 5-12 1RV81012 RV81 1-1/4" 5-12 1RV81015 RV81 1-1/2" 5-12 1RV91020 RV91 2" 5-12 1RV91025 RV91 2-1/2" 3-8 1RV111030 RV111 3" 5.5-15 1325 SERIES LEVER ACTING DESIGN. (Main burner & pilot applications)3253-6 325-3 /12A09 3/8" 2-6 103253-8 325-3 /12A09 1/2" 4-12 10 325-3L/12A09 1/2" 7-11 23255AL-12 325-5AL 3/4" 7-11 23255A-12 325-5A 3/4" 4-12 103255AL010 325-5AL 1" 7-11 23255A010 325-5A 1" 4-12 103257012 325-7 1-1/4" 12-Apr 103257015 325--7 1-1/2" 4-12 10R & 210 SERIES BALANCED VALVE DESIGN. (Main Burner & Pilot, larger Higher Pressure Applications)R600S010 R600S 1" 10-22 5210D010 210D 1" 4-8 10210D015 210D 1-1/2" 5-15 10210E020 210E 2" 5-15 10210G030 210G 3" 15-30 10Note: Replacement springs and optional springs for other ranges are available for these pressure regulators. Some application assistance is required. Please call us to assist you in selecting the proper spring.

maxitrol low press gas reg 7/24/2008

________________________________MAXITROL

LOW PRESSURE REGULATOR SPRINGSOrder No. Model No. Color Code Range (In. WC) Valve Model

R5310512 R5310-12 BLUE 5-12" RV53/R600R611038 R6110-38 PINK 3-8" RV61R811038 R8110-38 PINK 3-8 RV81/210DR81101022 R8110-1022 RED 10-22 RV81/210DR911038 R9110-38 PINK 3-8 RV91/210ER91101530 R9110-1530 YELLOW 15-30 RV91/210ER325C26 R325C26 PLATED 2-6 325-3R325E1022 R325E1022 RED 10-22 325-5A

maxitrol low press springs 7/24/2008

NOTE: Tech Tip# 37 on page 346 explains how to select and size gas regulators.


4

MAXITROL________________________________

12A SERIES GAS PRESSURE REGULATOR ACCESSORIESLimits gas escapment to within ANSI standards should diaphragm rupture. For use with certain 325 series regulators.Order No. Model No. Description

12A04 12A04 AUTOMATIC VENT LIMIT DEVICE 1/8" NPT, for 14" WC - use on RV48, 52, 53, 6112A09 12A09 AUTOMATIC VENT LIMIT DEVICE 1/8" NPT, for 2# LP & # 5# nat. gas, 325-3, 325-3L, 325-3LX12A39 12A39 AUTOMATIC VENT LIMIT DEVICE 3/8" NPT, for 2# LP# & 5# nat. gas, 325-5A, 325-5AL, 325-ALX

maxitrol 12a series reg access 6/12/2008

Order No.TS114 55 - 90º F.

Description

DISCHARGE AIR SENSORThe discharge air sensor is to be used with an existing mixing tube or we can Special Order a mixing tube for new installations.

Order No.

13A15

REGULATOR VENT PROTECTORVent protector is designed for outdoor applications. Use on vent opening to protect breather hole from rain, snow, dust or other foreign particles and insects.

DescriptionVent protector for gas regulators

MAXON___________________________________


4

___________________________________MAXON


4

For further information on MAXON products, please call Federal.

MAXON __________________________________

Order No. Model No. Application/Description61 140100 Installed with 1" steam and water equalizing lines. Requires separate blow-off valve.67 149400 "Quick Hook Up" fittings, deep sediment chamber, self-closing blow-off valve, adjustable conduit

outlet, 1/4" NPT tapping.69 153900 Fits 2-1/2" NPT tappings. "Built-in" low water cut-off. 4-1/8" insertion length.

Full load amps: 7.4 @ 120 VAC, 3.7 @ 240 Vac

LOW WATER CUT-OFFS FOR LOW PRESSURE STEAM BOILERSFor boilers of any size. UL listed.SPECIFICATIONSMaximum steam pressure: 20 psi

MC DONNELL & MILLER____________________

Please visit page 316 for Tech Tip #18 which has a wealth of valuable information on steam boiler controls.


4

____________________MC DONNELL & MILLER

Series 63

63, 64 SERIES LOW WATER CUT-OFFS

Order No.

Boiler Size

Maximum Boiler Pressure Method of Installation Description

63 Any size 50 psi 1" NPT top and bottom equalizing pipes Provides a test opening64 Any size 50 psi 1" NPT top and bottom equalizing pipes Utilizes a no. 11 cut-off

and alarm switch

FOR HOT WATER OR STEAM

Model No.142400143600

MCDONNELL 63, 64 SERIES 6/12/2008

Order No. Model No. Description750MT120 176207 CONTROL W/MANUAL RESET AND TEST SWITCH750PMT120 176234 CONTROL W/MANUALRESET & PROBE PA800 AND TEST SWITCH750T120 176206 CONTROL W/AUTO RESET AND TEST SWITCH

SERIES 750 LOW WATER CUT-OFFS - ELECTRONIC FOR HOT WATER AND STEAM BOILERSLow water cut-offs with remote sensor for commercial and industrial applications. Features include electronic circuitry with remote conductance probe level sensing; LED low water indicator light; optional manual reset and test switches available; no lock out with loss of power (if probe is in water). Model 750-MT-120 meets ASME Code CSD-1 requirements. Maximum ambient temperature 130oF; voltage across probe to ground 14 VAC.

MCDONNELL MILLER SERIES 750 LOW WATER CUT-OFFS

FS SERIES LIQUID FLOW SWITCHES

Order No. Model No.Spdt

SwitchUse on

Pipe Sizes Connection

Primary Wetted Parts

Maximum Pressure

Fluid Temperature

Minimum Ambient

Temperature Switch Enclosure

FS251 114400 1 1-6" NPT Brass 160 psi 32-250oF 32oF General PurposeFS254 120601 1 1-6" NPT Brass 160 psi 32-250oF 32oF NEMA 4XFS5-12 114760 1 3/4" NPT Brass 150 psi 32-250oF 32oF General Purpose

HIGH SENSITIVITY APPLICATIONSFS1 113200 1 1/2" NPT Brass 100 psi 32-225oF 32oF General PurposeFS6010 115600 1 1" NPT Brass 100 psi 32-225oF 32oF General Purpose

INDUSTRIAL/HEAVY DUTY APPLICATIONSFS74 119700 1 1-1/4--16" NPT Brass 300 psi 32-300oF 32oF General PurposeSpecial Order FS7-4S 1 1-1/4--16" NPT S.S. 1,000 psi 32-300oF 32oF General Purpose

Locked rotor: 44.4 @

GENERAL PURPOSE APPLICATIONS

For making (or breaking) an electric circuit when liquid flow starts or stops.SPECIFICATIONSSwitch rating (amps): Full load: 7.4 @ 120 Vac; 3.7 @

Pilot duty: 125 VA; 120-240V

REPLACEMENT PARTS FOR FLOW SWITCHESOrder No. Model No. Application/Description Where Used

FS415 336800 PADDLE KIT FS4-3, FS8.WFS117 304300 SWITCH FS-1,4-3,5,6,8-W AFE-1FS433 305200 SWITCH ALL FS4-3 UNITS (EXCEPT D)

MCDONNELL FS REPL PARTS 8/1/2008


4

MC DONNELL & MILLER____________________

Order No. Model No. DescriptionPS851M120 153896 WITH MANUAL RESET

SERIES PS-850 LOW WATER CUT-OFF FOR HOT WATER BOILERS

For residential, commercial and industrial hot water boilers, this series includes electronic operation LED low water indicator light, test switch and LED indicator light, no lock out with loss of power (if probe is in water). No blow down required and no moving parts. Voltage across probe to ground is 14 VA, probe sensitivity 3,500 ohms at 120 or 24 VAC supply. Power consumption 3 VA. Meets ANSI specifications Z21,13A. Maximum water pressure 160 psi. Maximum water temperature 250oF.

LOW WATER CUT-OFF WITH REMOTE SENSOR FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS

MCDONNELL MILLER SERIES 850 LOW WATER CUT-OFFS

FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS

Order No. Model No. Part No. DescriptionRS1BR1 RS-1-BR-1 179524 REMOTE SENSOR

Maximum water temperature 406oF

Maximum water pressure 250 psi

RS1BR1 LOW WATER SENSOR

MCDONNELL MILLER RS1BR1 LOW WATER SENSOR

Series 51

Series 21

BOILER WATER FEEDER AND FEEDER CUT-OFF COMBINATION

Order No.

Model No. Description

Maximum Boiler

PressureMaximum Water Supply Pressure

21 126400 21 Make-Up water feeder for boiler reciever tanks 35 psi 150 psi47 136900 471 or 47-2; includes quick hook-up fittings, 1/2" pipe connection. 25 psi 150 psi247 135600 247' or 247-2; like #47, but has 1" pipe connection no quick hookup fitting 30 psi 150 psi51 134700 511 or 51-2; 1" pipe connection. 35 psi 150 psi51S 135600 51S1 or 51S-2; 1" pipe connection, highest capacity feeder. 35 psi 100 psi

53 136900 531 or 53-2; similar to 51, heavy-duty components for higher pressures. 75 psi 150 psi1 Boiler feder only, without #2 cut-off switch. #2 or #2M (manual reset) switch can be field added.

Mechanically adds water as needed to maintain water level, and electrically stops burner in case of low water condition. These can be used on steam or hot water boilers. See manufacturer's literature for feeder capacities.

MCDONNELL FEEDER & CUTOFF COMBO 8/1/2008

MAKE-UP WATER FEEDERS

Order No.

Model No.

Maximum Body Pressure

Maximum Supply

Pressure Description

25A 126800 35 psi 100 psiFloat operated feeder. Mounted to the tank with 1" NPT top and bottom equalizing lines. Feeds water through a separate pipe.

21 126400 35 psi 150 psiFlange mounts on side of receiver with six bolts. Flange bolt circles No. 21-5-3/4"; No. 221-8-1/2".

In higher pressure boiler feed systems, it serves to add make-up water to the receiver when necessary so there is always an adequate supply for boiler demand.

MCDONNELL MAKEUP WATER FEEDER 6/13/2008


4

MC DONNELL & MILLER____________________ ____________________MC DONNELL & MILLER

Model 150

Model 157

Order No. Model No.Maximum Boiler

Pressure Switches Description42SA 50 psi Snap

acting"Quick hook-up" fittings. Completely packless. Float operated. Installed with 1" NPT equalizer pipes.

93 162300 150 psi Snap acting

Combination pump controller/low water cut-off,1" NPT connection.


Combination pump controller/low water cut-off,1 1/4" NPT connection.

150EHD 171640 150 Electro- nic

Head mech electronic for 150E automatic reset

150EMHD 171650 150 Electro- nic

Head mech electronic for 150EM manual reset

150MHD 173200 150 psi Mercury Auto

Head mech mercury manual reset

150SMD 171802 150 psi Snap acting

For boilers with separate water columns; with maximum differential option.

150SMMD 172802 150 psi Snap acting

For boilers with separate water columns. Packless. Includes manual resets on cut-off switch; with maximum differential option.

157SMD 173603 150 psi Snap acting

Water column type body, with all tappings for steam trim . Integral water column. For larger tapping over 157-A. For glass tapping inside of body, order 157R and 157RL. Model has maximum differential option. All models available with manual reset on cut-off switch by adding suffix M.


Combination pump controller/low water cut-off, 1" connection, water column with integral tappings for gauge glass & tri-cock installation.


Combination pump controller/low water cut-off, 1 1/4" connection, water column with integral tappings for gauge glass & tri-cock installation.

Note: For boilers of any size

PUMP CONTROLLERS AND LOW WATER CUT-OFFS FOR STEAM BOILERSFLOAT ACTUATED ELECTRICAL SWITCHES - first switch turns pump on, second switch cuts off burner

controllers MCDONNELL PUMP CONTROLLERS 8/1/2008

For 150, 157 and 42 Series. UL Listed.

Motor Duty 120 Vac. 240 Vac. 120 Vdc. 240 Vdc.Full Load 7.4A 3.7A 2.4A 1.2ALocked Rotor 44.4A 22.2A 24.0A 12.0APilot duty service: 34 VA @ 120/240 Vac

ELECTRICAL RATINGS FOR PUMP AND CUT-OFF CIRCUITS

ratings1 MCDONNELL PUMP CONTROLLERS 8/1/2008

Order No. Model No. Application/Description Where Used25AHD 127100 Replacement Head Assy. 25A42SHD 129502 Replacement Head Assy. 42, 42A51HD 134900 Replacement Head Assy. 5163HD 142600 Replacement Head Assy. 63 Series64HD 144400 Replacement Head Assy. 64 and 764 Series93HDLS 162402 Replacement Head Assy. Less Switch 93 SeriesSpecial Order 162600 Head Mech. Manual Reset 93 and 193 Series94MHD 166000 Head Mech. (W/5M Switch) Manual Reset 94 and 194 Series150SHD 173003 Head Mech. Over 50# Pressure Auto Reset, Snap Switch 150 and 157 Series150SMDHD 173103 Head Mech. Max. Diff., Snap Switch 150(MD), 157(MD)150SMHD 173203 Head Mech. Man. reset, Snap Switch 150 and 157 Series150SMMDHD 173302 Head Mech. Man. Reset, Max. Diff., Snap Switch 150 and 157 Series6667 153825 6667 Comp. Mech. 120VAC for 115V or 230V Circuits 61, 67, 69 and 70 Series150EHD 171640 Head Mech. Elec. 150# max w/auto reset 150150EMHD 171650 Head Mech Elec 150# max w/ Manual reset 150

INCLUDES ALL OPERATING PARTS EXCEPT FLOAT BOWL

REPLACEMENT HEAD MECHANISMS FOR FEEDERS, CUT-OFFS AND PUMP CONTROLLERS

MCDONNELL HEAD MECH REPL PARTS 7/28/2008


4

MC DONNELL & MILLER____________________FLOAT OPERATED SWITCHESSPECIAL ORDER

Order No.Model

No.Maximum Pressure Description

Special Order 65 40 psi

Special Order 80 5 psi Single pole double throw switch. Mercury switch inside float. 1/2" NPT tappings. Maximum temperature 190oF.

Hazardous duty. Float operated controller. Opens circuit with falling level. Reverse acting.

MCDONNELL FLOAT SWITCH 6/12/2008

For additional information on McDonnell & Miller products and helps, go to www.mcdonnellmiller.com

SWITCHESOrder No. Model No. Description Where Used

5 110300 SWITCH ASSEMBLY All controls using #5 switchSA150106R 347900 BELLOWS 150SWA150SMD 310464 SNAP ACTING SWITCH 15011 309100 SWITCH 61, 64, 67, 69, 702 110000 CUT-OFF/ALARM SWITCH 47, 51, 53, 632M 110100 CUT-OFF/ALARM SWITCH 47, 51, 53, 635M 110400 SWITCH ASSEMBLY MANUAL 93/193/94/1947B 110800 SWITCH ASSEMBLY 93/94, 193/1947BM 110900 PROP. SWITCH WITH MANUAL RESET 93/94/193/194

GASKETSOrder No. Model No. Description Where Used

15014 150-14H HEAD GASKET (1 ONLY) 150,15737101 324435 O-RING 21,47,101-A3726 3726 BODY GASKET (1) 47/47-2,247,247-23739 3739 BLOW-OFF VALVE GASKET (1) 47,53,67,703727 312800 VLV BRACKET GSK (1 ONLY) 47, 51, 53, 315S6712 318800 FLOAT GASKET (1 ONLY) 61, 64, 67, 70, 8084726 84726 HEAD GASKET (1 ONLY) 851,847,851-S9268 323300 HEAD GASKET (1 ONLY) 94, 194CO11 CO11 BELLOWS BASE GASKET (1) E-28, 63CO12 CO12 HEAD GASKET (1 ONLY) 42,61,63,64,65,42SF26 302600 HEAD GASKET (1 ONLY) 221,25-A,51-S,51-S-2,53/53-

2,315S, 551-S

FLOATSOrder No. Model No. Description Where Used

SA15011 347600 FLOAT AND ROD 150SA3730 340600 FLOAT 47FLT51 310480 FLOAT 51, 3155FLT5105 310437 FLOAT 51, 3155

MISCELLANEOUS PARTSOrder No. Model No. Application/Description Where Used

7B1R 309000 RESISTOR & SLIDEWIRE KIT 7B,93,193,94,19414B 310447 BLOW-OFF VALVE ASSMBY. 47,67,70BBA5105 BELLOWS ASSEMBLY 310439 NEW STYLE FEB 05 OR LATERCTRD51 310452 CARTRIDGE/STRAINER KIT, 51 SERIES 51,851CTRD101 CARTRIDGE/STRAINER KIT,101A SERIES 47,101A,247,847PA800 354081 PROBE PS800,850 SERIES W/ REMOTE

PROBESA47101102 341600 VALVE & STRAINER ASSEMBLY 47,247,847SA2138R 339700 STRAINER BASKET ASSEMBLY 21SA474 341500 LARGE SIPHON ASSEMBLY 47SA51101102 342500 VALVE & STRAINER ASSEMBLY 51SA642 343500 BELLOWS BASE ASSEMBLY 64

REPLACEMENT PARTS FOR LEVEL & BOILER CONTROLS - (CONT.)

REPLACEMENT PARTS FOR LEVEL & BOILER CONTROLS - CONT.

REPLACEMENT PARTS FOR LEVEL & BOILER CONTROLS

MCDONNELL LEVEL & BOILER REPL PARTS 7/28/2008


4

MC DONNELL & MILLER____________________ __________________________________POWERS

100 psig 200oF

100 psig

Order No. Model No.Temperature

Range Inlets Outlets 5 20 45 60 100 Finish

4311000 431-1000 65-115oF 2 min., 8 max. 3/4" 3/4" 7.5 16 25 29 38.5 Satin Spray4321000 432-1000 65-115oF 3 min., 15 max. 3/4" 1" 15 30 45 52 67 Satin Spray1 With 140oF hot inlet, 60oF cold inlet and 100oF delivery temperatureNote: all units have brass body with noncorrosive parts

Group Shower Capacity (No. of 3

gpm Heads Served)

Capacities (in gpm)1 As Related to Pressure Differential (psi)

SPECIFICATIONSMax. pressure differential:Max. static pressure:

Max. hot water temp.:

430 SERIES HYDROGUARD THERMOSTATIC CONTROLSFOR MULTIPLE SHOWER-HYDROTHERAPY-INDUSTRIAL PROCESSThermostatically blends hot and cold water to desired temperatures, compensates for both temperature and pressure changes on the supply lines and protects against water supply failure. For larger capacity requirements, two or more Hydroguards can be teamed up to provide progressive rinse or wash down sprays. Features include: Self-aligning bronze trim; balanced and independently seated hot and cold water valves; tamper-proof temperature adjustment control; union inlets for an infinite variety of piping arrangements and easy servicing; combination strainer-check-stops.

Selection warning: Do not oversize. Minimum recommended flow should have 5 psi drop. Industry standard is 45 psi pressure drop.

POWERS 430 SERIES 7/28/2008

590 SERIES #11 LOWER HOUSING ASSEMBLIES (VALVE BODY)

Order No. Model No. Body Style Size Valve ActionSpecial Order 590-CD-075H Single Seat Comp. Disc 3/4" Heating590ST075H 590-ST-075H Single Seat SS Trim 3/4" HeatingSpecial Order 590-DS-100-H Double Seat SS Trim 1" HeatingSpecial Order 590-ST-050-H Single Seat SS Trim 1/2" HeatingSpecial Order 590-ST-100-H Single Seat SS Trim 1" Heating

FOR NON-ELECTRIC TEMPERATURE CONTROL-FOR HEATING, COOLING OR MIXING, SELECT THERMAL SYSTEM TO ACTUATE VALVE

bodies POWERS 590 series 7/28/2008

ACCESSORIESOrder No. Model No. Description For Use With

590184A 590-184A Valve Stem Lubricator Recommended to keep stem moving freelyP590164 111 Valve Stem Lube #590184A Stem Lubricator

accessories POWERS 590 series 7/28/2008

Order No. Model No. Description Type Temperature Range

7441214 744-1214 Reverse Acting 1 Air Operated, includes gauges 50-350oF1 Can be converted to direct acting in field

ACCRITEMPNEUMATIC TEMPERATURE CONTROLLERSFor control of Flowrite or other pneumatic operated valves, for heating DHW or other process applications.

#11 THERMAL SYSTEM REGULATOR VALVES

Order No. Model No.Bulb and Cap.

Material Cap Length Bulb Style Head AssemblyTemperature

Range1

Special Order 700-C-08-D-I Copper 8' Fixed Union Indicating 55-115oFSpecial Order 700-C-08-D-I Copper 8' Fixed Union Indicating 110-170oFSpecial Order 700-C-08-D-I Copper 8' Fixed Union Indicating 140-200oFSpecial Order 700-C-08-D-N Copper 8' Fixed Union Non-Indicating 85-145oF700C08DN05 700-C-08-D-N Copper 8' Fixed Union Non-Indicating 110-170oF1 Temperature range represents a summary of the separate heating, cooling and water mix ranges. Consult the manufacturer for each individual range. For best performance, select range with a setpoint in the upper third.

For non-electric temperature control, for heating, cooling or mixing. Select 590 valve and 700 thermal system for complete system.

bodies POWERS #11 series 7/28/2008

STYLE "S" WELLS

Order No. Model No. Material Well Dia. 1X9" Bulb 1X20" Bulb Shock Non-ShockSpecial Order 709-075 Chrome Plated Copper 1" ---- 22" 175 psi 675 psi

Max. Well PressureWell-Length

style s wells POWERS #11 series 7/28/2008


4

ROBERTSHAW_____________________________

Order No. Model No. Valve Size Voltage Regulator Setting Capacity1

R700059 700-059 1" 24/60 4.0" Nat Gas 720,000R700442 700-442 1" 24/60 3.5" Nat Gas 600,0001 1000 Btu/Cu. Ft. 0.64 sp. gr. natural gas or 2500 Btu/Cu. Ft. 1.53 sp. gr. L. P. gas @ 1" W.C. pd.

700 SERIES COMBINATION GAS VALVESDesigned for intermittent pilot, direct spark and hot surface applications, these valves incorporate a manual valve, pilot valve and a main gas pressure regulator. They are designed for many residential and commercial applications such as central heating units, wall heaters, boilers and mobile home furnaces.

ROBERTSHAW 700 SERIES GAS VALVE 9/8/2008

SENSUS__________________________________

SIEMENS_________________________________

UNDER 500 CUBIC FEET PER HOUR

R-275 R-315 415• Residential / Domestic: Average Volume • Residential / Domestic: Medium Volume • Residential / Domestic: Larger

Volume• Operating temperature range: --30°-150° F • Operating temperature range: --30° - 150° F • Operating temperature range: --

30° - 150° F

DOMESTIC/RESIDENTIAL GAS METERS

Sensus domestic / residential meters incorporate the latest design concepts with modern engineering materials to provide lighter weight, easier to handle and more durable meters that require less maintenance and offer greater life expectancy. They feature a modular design that reduces repair time and costs. They are available in both temperature compensated and non-temperature compensated versions.

A variety of index options are provided for Equimeter residential meters. Plastic circular (dial) and direct (odometer) reading indexes are available with 1', 2', or "2-foot, half-foot" proving hands. First reading circle values range from 10 to 1,000 cubic feet. All indexes are available in standard or temperature compensated configurations. Metric meters feature cubic meter indexes.

sensus domestic GAS METERS 7/10/2008

750 TO 10,000 CUBIC FEET PER HOUR

• ease of repair;• replaceability of the measurement module;• simple installation;

Sensus intermediate and large capacity meter cases are made of corrosion-resistant aluminum alloy castings and designed around our single joint concept. The single joint concept means a single seal joining the upper and lower halves of the meter body and incorporating the valve plate area. Coupled with complete interchangeable valve plate assemblies and lightweight aluminum bodies, this design offers several important benefits, including:

The full line of our intermediate and large capacity meters is available in both temperature compensated and non-temperature compensated versions.

INTERMEDIATE AND LARGE CAPACITY DIAPHRAGM GAS METERS

• Iighter weight for ease of handling and lower shipping costs; and - because of the single joint seal - minimal risk of leakage.

sensus LARGE GAS METERS 7/10/2008

SIEMENS CONTROL PRODUCTS

Siemens has a wide variety of control products available. No one distributor can possibly stock all of them. If you have a need for any of the Siemens control product line, please give us a call. Chances are we can order it in just for you. Most of the controls are readily available with a short lead time. Let us help you with your Siemens control needs.

siemens controls header 9/8/2008


4

____________________________SPIRAX SARCO

Style FTI

Style FT

Order No. Model No. Conn. Size 1 psi 5 psi 15 psi15 PSI MAX. STEAM PRESSURE (FT & FTI SERIES)FT15-12 50926 3/4" 489 785 1075FT15010 50927 1" 489 785 1075FT15012 51313 1-1/4" 980 1640 2340FT15015 57059 1-1/2" 2400 5000 7600FT15020 57063 2" 3600 6900 10900FTI15-8 66664 1/2" 489 785 1075FTI15-12 66669 3/4" 489 785 1075FTI15010 66674 1" 489 785 1075

Order No. Model No. Conn. Size 1 psi 5 psi 15 psi 20 psi20 PSI MAX. STEAM PRESSURE (FTB HIGH CAP. SERIES)FTB20020 58476 2" 4000 15500 22000 25000

Order No. Model No. Conn. Size 1 psi 5 psi 15 psi 30 psi30 PSI MAX. STEAM PRESSUREFTI30-12 66670 3/4" 489 785 1075 1370FTI30010 66675 1" 489 785 1075 1370

Order No. Model No. Conn. Size 15 psi 50 psi 100 psi 125 psi125 PSI MAX. STEAM PRESSURE (FTI SERIES)FTI125-8 66667 1/2" 500 830 1110 1190FTI125-12 66672 3/4" 500 830 1110 1190FTI125010 66677 1" 500 830 1110 1190

Order No. Model No. Conn. Size 15 psi 50 psi 100 psi 125 psi 200 psi200 PSI MAX. STEAM PRESSURE (FTI SERIES)FTI200-12 66673 3/4" 365 575 750 820 985

Capacity (lb/hr) Condensate @ Press. Diff. Shown


FLOAT & THERMOSTATIC STEAM TRAPS




Float & Thermostatic Traps discharge condensate at steam temperature continuously and modulate with the condensate load. They are recommended to drip low pressure steam mains, unit heaters, heat exchangers and are the first choice for all process applications requiring removal of condensate as quickly as it is formed. Air binding is impossible. These traps are equipped with with separate thermostatic air vents which remove automatically and immediately all air and gases reaching the trap. FTI have straight through flow patterns, while all other styles have entering and leaving connections on the same side of the trap.

FLOAT & THERMOSTATIC STEAM TRAPS con't

bodies sarco FT STEAM traps 7/28/2008

Order No. Model No. Conn. Size 5 psi 10 psi 15 psi15 PSI MAX. STEAM PRESSUREB1H15-8 B1H/64147 1/2" 835 960 1040B1H15-12 B1H/64159 3/4" 835 960 1040B215-12 B2/62755 3/4" 2370 2810 3220B315010 B3/6279 1" 2920 3590 3900B415012 B4/62781 1-1/4" 4980 5990 6560B515020 B5/62769 2" 14700 17800 20000

Order No. Model No. Conn. Size 60 psi 100 psi 125 psi125 PSI MAX. STEAM PRESSUREB1H125-8 B1H/64150 1/2" 695 830 920B1H125-12 B1H/64162 3/4" 695 830 920B2125-12 B2/62762 3/4" 1700 2080 2240B3125010 B3/62801 1" 3020 3640 4100B4125012 B4/62788 1-1/4" 6350 7750 8540B5125020 B5/62775 2" 15600 18900 20000

STYLE "B" INVERTED BUCKET STEAM TRAPSimple bucket and lever mechanism. Robust bodies with a variety of connections. Naturally resistant to waterhammer. Inverted bucket traps are the most robust of the mechanical types and employ the simple, well-proven operating principle of density difference between steam and water.

Capacity (lb/hr Condensate @ Press. Diff. Shown


bodies sarco style B bucket traps 7/28/2008

PARTS FOR BUCKET TRAPS

Order No. Model No. Application/Description Order No. Model No. Application/DescriptionSpecial Order 41939 BUCKET BRS FOR B3 Special Order 54734 MECH ASSY FOR B3-125Special Order 42439 BUCKET BRS FOR B4 Special Order 54740 MECH ASSY FOR B4-125Special Order 55551 STRAINER ASSY BRS B3 Special Order 54743 MECH ASSY FOR B5-15 OR B52-15

Special Order 55554 STRAINER ASSY SS B4 Special Order 55458 AIR VENT (OPTIONAL) FOR B1X,

B1H, B2Special Order 54719 MECH ASSY FOR B1H-15

OR B1X-1555543 55543 COVER GASKET FOR B1X OR B1H

(SET OF 3)64260 64260 MECH ASSY FOR B1H-125

B1X-125 Special Order 55544 COVER GASKET FOR B2 (SET OF 3)Special Order 54725 MECH ASSY FOR B2-15 55545 55545 COVER GASKET FOR B3 (SET OF 3)Special Order 54728 MECH ASSY FOR B2-125 Special Order 55546 COVER GASKET FOR B4 (SET OF 3)Special Order 54731 MECH ASSY FOR B3-15 55547 55547 COVER GASKET FOR B5 (SET OF 3)

parts sarco style B bucket traps 7/28/2008

Look at Tech Tip #34 on pages 340 & 341 and Tech Tip # 35 on pages 342 & 343 for steam trap tips.


4

TD52

TD42

SPIRAX SARCO____________________________

Order No. Model No. Conn. Size 1 psi 5 psi 15 psi15 PSI MAX. STEAM PRESSURE (FT & FTI SERIES)FT15-12 50926 3/4" 489 785 1075FT15010 50927 1" 489 785 1075FT15012 51313 1-1/4" 980 1640 2340FT15015 57059 1-1/2" 2400 5000 7600FT15020 57063 2" 3600 6900 10900FTI15-8 66664 1/2" 489 785 1075FTI15-12 66669 3/4" 489 785 1075FTI15010 66674 1" 489 785 1075

Order No. Model No. Conn. Size 1 psi 5 psi 15 psi 20 psi20 PSI MAX. STEAM PRESSURE (FTB HIGH CAP. SERIES)FTB20020 58476 2" 4000 15500 22000 25000

Order No. Model No. Conn. Size 1 psi 5 psi 15 psi 30 psi30 PSI MAX. STEAM PRESSUREFTI30-12 66670 3/4" 489 785 1075 1370FTI30010 66675 1" 489 785 1075 1370

Order No. Model No. Conn. Size 15 psi 50 psi 100 psi 125 psi125 PSI MAX. STEAM PRESSURE (FTI SERIES)FTI125-8 66667 1/2" 500 830 1110 1190FTI125-12 66672 3/4" 500 830 1110 1190FTI125010 66677 1" 500 830 1110 1190

Order No. Model No. Conn. Size 15 psi 50 psi 100 psi 125 psi 200 psi200 PSI MAX. STEAM PRESSURE (FTI SERIES)FTI200-12 66673 3/4" 365 575 750 820 985



FLOAT & THERMOSTATIC STEAM TRAPS




Float & Thermostatic Traps discharge condensate at steam temperature continuously and modulate with the condensate load. They are recommended to drip low pressure steam mains, unit heaters, heat exchangers and are the first choice for all process applications requiring removal of condensate as quickly as it is formed. Air binding is impossible. These traps are equipped with with separate thermostatic air vents which remove automatically and immediately all air and gases reaching the trap. FTI have straight through flow patterns, while all other styles have entering and leaving connections on the same side of the trap.

FLOAT & THERMOSTATIC STEAM TRAPS con't

bodies sarco FT STEAM traps 7/28/2008

PARTS FOR FLOATS & THERMOSTATIC TRAPSOrder No. Model No. Application/Description Order No. Model No. Application/Description

54749 54749 VALVE MECH ASSY 3/4--1" FT-15 58129 58129 FLOAT 1-1/2 FT-15 54751 54751 VALVE MECH ASSY FTI-125 (1/2

,3/4 ,1")Special Order 58130 FLOAT 2" FT-15

54752 54752 VALVE MECH ASSY 1-1/4" FT-15 55475 55475 GASKET KIT FT/FA (SET OF 3) FT Special Order 58131 VALVE MECH ASSY 1-1/2" FT-15 58127 58127 GASKET 1-1/2 FT15 (KIT)Special Order 58135 VALVE MECH ASSY 2" FT-15 58128 58128 GASKET 2" FT, ALL

PRESSURES(SET OF 3)55447 55447 FLOAT FT15 1-1/4" AND FA150, FTI

(30-200#)67049 67049 GASKET SET FOR ATT FTI

Special Order 55448 FLOAT FTI-15, 3/4 & 1" FT-15 62652 62652 AIR VENT ASSY FOR FT SERIES

parts sarco FT STEAM traps 7/28/2008

Order No. Model No. Description Conn. Size 5 psi 50 psi 100 psi 200 psi 400 psi 600 psiTD52-6 54529 Standard 3/8" 185 245 370 610 960 1250TD52L-8 54771 Reduced Capacity 1/2" 185 245 370 610 960 1250TD52-8 54530 Standard 1/2" 310 575 810 1140 1630 2000TD52L-12 59314 Reduced Capacity 3/4" 310 575 810 1140 1630 2000TD52-12 54531 Standard 3/4" 420 810 1160 1670 2430 3050TD52010 54532 Standard 1" 670 1200 1750 2600 3780 4700TD42L-8 680790 Reduced w/strainer 1/2" 150 240 320 470 615 700


TD-52 & TD-42 SERIES THERMO-DYNAMIC Just one moving part—a hardened, stainless steel disc. Withstands superheat, waterhammer, freezing, corrosive condensate and vibration. Works in any altitude. Typical applications include: Steam tracing lines, steam main drips, process equipment, laundry and kitchen equipment, superheated steam applications, and outdoor installations subject to possible freezing. Model TD52L is low capacity. Model TD42L is low capacity with built in strainer, with option to add blowdown valve.

sarco TD-52 traps 7/28/2008

Order No. Model No. Application/DescriptionRTA125-8 66437 1/2 ANGLE THERM TRAP W/STD SPUDRTA125-12 66439 3/4 ANGLE THERM TRAP W/STD SPUDSPECIAL ORDER 70589, RTH-125 1/2 STRAIGHTWAY TRAP

THERMOSTATIC STEAM TRAPSFOR RADIATORS, LAUNDRY AND KITCHEN EQUIPMENT, TRACING LINES, STEAM MAIN DRIPSThe unique capsule element resists superheat and waterhammer. The ball cone valve head ensures tight shutoff. The thermostatic elements are entirely stainless steel. Because the trap is wide open when cold, start-up time is reduced.

bodies sarco THERMOSTATIC STEAM traps 7/28/2008


4

____________________________SPIRAX SARCO

1/4” FA 150

3/4” FA 150

VS204

13WS

Order No. Model No. Application/Description Conn. Size ConstructionVB14 190190 VACUUM BREAKER 1/2 x 1/8" 210 psi Brass body, SS internals

VACUUM BREAKER

Max. Pressure

Some of the most troublesome heat transfer problems are caused by condensate flooding equipment due to vacuum. Model VB14 corrects this problem by equalizing system pressure and allowing condensate to drain, thus improving heat transfer, and equipment life by avoiding waterhammer.

sarco VACUUM BREAKER 7/28/2008

Order No. Model No. Application/DescriptionUBP32TRAP 1270500 TRAP BAL PRESS LESS CONNECTORUBP30-12 66180 3/4 SWIVEL CONN ONLY UBP30Special Order 66178 1/2 SWIVEL CONN ONLY UBP30

THE ULTIMATE TRAP FOR STEAM MAIN DRIP LEG APPLICATIONSPressures up to 435 psi steam. Adequate capacity for any drip leg. Balanced Pressure feature insures condensate discharge 5-20oF below steam temperature. Resists waterhammer and freezing. Select ½" or ¾" swivel connector with trap body.

UPB30 THERMOSTATIC STEAM TRAP

sarco UBP30 THERMOSTATIC STEAM traps 7/28/2008

Order No. Model No. Description 1 psi 10 psi 50 psi 100 psi 150 psiFA150-12 52589 DRAIN TRAP 3/4" 150 330 840 1550 2050 2400FA150-4 59279 STAINLESS DRAIN

TRAP1/4" 150 125 330 650 900 1025

Capacity (lb/hr Cold Water @ Press. Diff. Shown

FA SERIES LIQUID DRAIN TRAPSAutomatic drain traps for compressed air and other pressurized gases. When compressed, air cannot retain the moisture normally found at atmospheric pressure, the moisture is literally "squeezed out". Unless it is removed it is harmful to the distribution system and the equipment. This float operated drain trap which fully modulates and responds instantaneously to any change in flow will efficiently drain the system. For liquids of specific gravity down to 0.5.

Max. Diff. Pressure

Conn. Size

bodies sarco FA SERIES traps 7/28/2008

PARTSOrder No. Model No. Application/Description

55475 55475 COVER GSKT KIT FT/FA (SET OF 3)Special Order 58153 VALVE MECH ASSY 3/4 FA-150

sarco FA SERIES traps 7/28/2008PARTS

Order No. Model No. Application/Description MaterialsT202 61292 Thermostatic Air Vent, Steam Sys. 3/8 X 1/4"125# steam Brasss body, SS internalsVS204 61685 Thermostatic Air Vent, Steam Sys. 1/2" 250# steam CI Body, SS internals13WS-12 13WS-12 Float Type Air Vent, Hydronic Sys. 3/4" 150# water CI Body, SS internals, EPDM vlv head69843 69843 Float Type Air Vent, Hydronic Sys. 3/4" 150# water CI Body, SS internals, EPDM vlv head

AIR VENTSA must for every piping system to eliminate air and any non-condensable gas that retards circulation and reduces heat transfer efficiency. Install 13WS in hydronic systems at all piping system and equipment high points--wherever air can collect. VS204 is installed at end of steam mains, and on equipment where air might be pushed as steam fills the system on cold startup.

Max. PressureConn. Size

bodies sarco AIR VENTS 7/28/2008

PARTSOrder No. Model No. Application/Description Order No. Model No. Application/Description55548 55548 COVER GASKET 3/4 13W (SET OF 3) Special Order 57453 VLV HD ASSY 3/4 13W Special Order 57406 VLV SEAT 3/4 13W Special Order 55448 FLOAT FOR 13W

PARTS sarco AIR VENTS 7/28/2008


4

SPIRAX SARCO____________________________

MAIN VALVE

Order No. Model No. Size/Connection Max Steam Pres

25-8 55222 1/2" NPT 250 psi

25-12 55223 3/4" NPT 250 psi

25010 55224 1" NPT 250 psi

25012 55225 1-1/4" NPT 250 psi

25015 55226 1-1/2" NPT 250 psi

25020 55227 2" NPT 250 psi

Special Order 54697 2-1/2" 125# FLG 125 psi

25030 54681 3" 125# FLG 125 psi

PRESSURE PILOTSOrder No. Model No. Application/Description Spring Color Pressure Range25P330 54819 PRESSURE PILOT Yellow 3-30 psi25P20100 59607 PRESSURE PILOT Blue 20-100 psi

TEMPERATURE PILOTS

Order No. Model No. Application/Description Temp. RangeBulb Style Model & Length of Cap Tube

25T60120 65233 TEMP PILOT 60-120F T2, 8FT25T100160 63629 TEMP PILOT 100-160F T2, 8FT25T120180 63630 TEMP PILOT 120-180F T2, 8FT25T160220 63631 TEMP PILOT 160-220F T2, 8FT

ELECTRICAL PILOTOrder No. Model No.S25E 63951 NEMA 4&7 PILOT 115V, 250# Max pressure

Application/Description

25 SERIES PILOT-OPERATED REGULATORS

The 25 Series is a versatile family of self-powered regulators with control pilots and interchangeable main valves for every application. You can combine up to three pilots (pressure, temperature and/or electrical) on a valve for a dependable and economical multiple control installation.

FOR REGULATION OF STEAM BY PRESSURE, TEMPERATURE AND/OR ELECTRICAL ON-OFF. CI CONSTRUCTION.

bodies sarco 25 SERIES 8/1/2008

ACCESSORIESOrder No. Model No. Application/Description

55717 55717 ADAPTER BRACKET KIT, FOR BUILDING 25PT OR PTE

56967 56967 25E PILOT CAP W/GASKET & BOLTS53916 53916 T6 340SS WELL

PARTSOrder No. Model No. Application/Description

52152F 52152 RED SPRING FOR 25P PILOT, FOR CHANGING LOWER PRESSURE PILOT TO 80-250#57155 57155 GASKET KIT FOR 1/2 OR 3/4" 2557156 57156 GASKET KIT FOR 1" 25Special Order 57157 GASKET KIT FOR 1-1/4" 2557158 57158 GASKET KIT FOR 1-1/2" 2557159 57159 GASKET KIT FOR 2" 2557160 57160 GASKET KIT FOR 2-1/2" 2557161 57161 GASKET KIT FOR 3" 2557305 57305 TRANS TUBING W, FTGS FOR 2" #2567225 57167 DIA ASSY FOR P PILOT67194 67194 SQ GSK FOR ALL 25 PILOTS (3 PER KIT)68780 68780 DIA FOR 1/2 & 3/4 25 (SET OF 2)68781 68781 DIA FOR 1 THRU 1-1/2 25 (SET 2)68782 68782 DIA FOR 2 25 (SET OF 2)68783 68783 DIA FOR 2-1/2 & 3 25 (SET OF 2)80201 80201 PRESSURE PILOT COVER W/RETAINING RING

PARTS sarco 25 SERIES 8/1/2008


4

___________________________SPIRAX SARCO

SB VALVE BODYOrder No. Model No. Size Cv P Band (deg F)1 Max Steam Pres

SB-8 0440490 1/2" NPT 3.0 8 250 psi

SB-12 0441490 3/4" NPT 4.5 8 150 psi

SB010 0442490 1" NPT 7.9 10 100 psi

SA121 ACTUATOR Order No. Model No. Range121R2 3850191 105-225oF

Range #2

ACCESSORIES (use union for direct insertion, use well for indirect insertion)

Order No. Model No.121UNION 0460379121BRWELL 0460579

CAPACITIES (lbs steam/hr)1/2" 3/4" 1"

Inlet psi Outlet psi3 0 64 96 1685 1 76 114 2007 2 88 132 231

10 5 95 143 25015 9 114 172 30150 0/22 311 466 818

100 0/52 550 825 1450150 0/80 790 1185250 0/138 1270

Description

SB/SA121 DIRECT OPERATING TEMPERATURE REGULATORThe SB/SA121 non-electric control valve and actuator is the simple answer to controlling steam to a heat exchanger to maintain temperatures. This regulator gives stable, modulating control within close tolerances. Because these systems operate through liquid expansion within a friction free bellows, they have a long maintenance free life with repeatable performance. "Set and forget" this controller. One SA121 controller can handle ranges of temperature from 105o to 225o F. Select a valve body, actuator and either a union kit or thermal well for a complete system.

13 Ft. captube, dial style adjustment control at sensor

Temp. Probe Dimensions

1 The proportional band (P Band) is the difference required between the desired set temperature and the actual controlled temperature to open the valve fully. For example, a 3/4" SB valve will not fully open until the controlled temperature drops to 8o F below the set point.

Brass well 121, 1"MPT x 12.5" L

Representative Steam Pressures

Union Kit 121, for use of probe w/o well

1" D x 12.2" L

Description & Dimensions

bodies sarco SB SA temp reg 7/28/2008

Order No. Model No. Conn. Size NPT Order No. Model No. Conn. Size NPT

CAST IRON BODY, 250 PSI SWP1 CAST STEEL BODY, 984 PSI SWP2 continuedSpecial Order 60308 1/4" CT012 52078 1-1/4"Special Order 60309 3/8" CT015 52079 1-1/2"IT-8 60310 1/2" CT020 52080 2"IT-12 60311 3/4" REPLACEMENT SCREENS3

IT010 60312 1" Special Order 53822 1/4" or 3/8"IT012 60313 1-1/4" 53828 53828 1/2"IT015 60314 1-1/2" Special Order 53834 3/4"IT020 60315 2" 53840 53840 1"CAST STEEL BODY, 984 PSI SWP2 53846 53846 1-1/4"CT-8 52075 1/2" 53852 53852 1-1/2"Special Order 52076 3/4" 53858 53858 2"CT010 52077 1"

IT & CT SERIES Y-STRAINERS

3 Will fit styles IT, CT, BT--20 mesh stainless steel.

1 250 psi maximum steam pressure (non shock), 300 psi (non shock), water oil or gas @ 150oF max.2 984 psi maximum steam pressure (non shock), 1,480 psi (non shock), water oil or gas @ 150oF max.

All strainer screens are 20 mesh stainless steel with other mesh available from the factory. Spirax Sarco strainers offer a vital safeguard against dirt, scale, rust and other foreign particles which are common in pipelines, and provide inexpensive insurance for protecting equipment. IT & CT Series have NPT connections.

sarco Y STRAINERS 7/28/2008


4

For additional information on Spirax Sarco products, go to www.spiraxsarco.com

SPIRAX SARCO____________________________

Order No. Model No. & Conn. Application/Description Construction

Approx. Cap. (lb/hr) Using SS check valves1

PRESSURE POWERED PUMPSSpecial Order APT14 1-1/2" x 1" Automatic Pump Trap, most compact Ductile Iron body/SS internals 1500PPEC PPEC 1" Pressure Powered Pump CI, Steel or SS body/SS internals 2150Special Order PPEC 1-1/2" Low Profile Pressure Powered Pump CI, Steel or SS body/SS internals 3350Special Order PPC 2" Pressure Powered Pump Ductile Iron body/SS internals 7400Special Order PPC 3" x 2" Pressure Powered Pump, high capacity Ductile Iron body/SS internals 9800150 psi motive, 15 psi backpressure.

CHECK VALVES (REPLACEMENTS ONLY; CHECK VALVE SET COMES WITH NEW UNIT)Order No. Model No. Application/Description Use With

Special Order 69901 2" SS WAFER CHECK VALVE W/GSK PPCSpecial Order 61776 1-1/2 BRZ CK VLV PKG (2/PKG) PPEC OR PPC62999 62999 EXHAUST VALVE PPEC63000 63000 INLET VALVE PPEC

PARTS AND ACCESSORIESOrder No. Model No. Application/Description Use With

60291 60291 SPRING ASSEMBLY PPC OR PPF66105 66105 COVER GASKET PPC OR PPF72962.3 72962.3 PIVOTROL COVER & MECH KIT PTC80084 80084 INLET VLV ASSEMBLY PPC OR PPFSpecial Order 80085 EXHAUST VALVE ASSEMBLY PPC OR PPFSpecial Order 66952 LINKAGE MECH KIT PPC OR PPF (ALL)Special Order 70937 PUSH ROD REPAIR KIT PPC OR PPFSpecial Order 64299 SPRING ASSEMBLY PPEC66413 66413 COVER GASKET PPECSpecial Order 70938 PUSH ROD REPAIR KIT PPEC

Both a pump and a pumping trap designed for trouble-free operation under all conditions. It transfers high temperature condensate or other liquids from a low point, low pressure or a vacuum to an area of higher pressure or elevation. Eliminates electric motors, float switches, seals and other maintenance problems normally associated with condensate return systems. The APT14 Pumping Trap is compact enough to be installed with steam coil or HX in tight quarters. The PPEC and PPC have large capacities for whole equipment rooms or systems.

PRESSURE POWERED CONDENSATE PUMPS

sarco PRESSURE POWERED PUMP 7/28/2008

APT14

Order No.

72962.3

PRESSURE POWERED PUMP KITDescription

Cover and mechanical kit for pressure powered pumps; replaces all but the body.

Tech Tip # 27 on page 332 has useful information on pressure powered pumps.


4

__________________________T.A.C. CONTROLS

AE-504 ELECTRIC PARALLELING RELAYS

SPECIFICATIONSInput signal: 100-1000 ohms potentiometerInput power: 24Vac, 50/60 Hz, 5VA normally supplied from an actuatorInput impedance: 50 ohms @ 0 Vac, 350 ohms @ 12 VacAmbient operating temp: 30-135oF

Order No. Max. Ohms

Watts per AE-

504

Max. no. of AE-504's per

Potentiometer Actuators Controlled

1001-135 1.5 3 MP-300, 400, 2000, 4000, 9700 Series, MP-98102

98302, 99102

3 1 MP-300, 400, 2000, 4000, 9700 Series,MP-98102

98302, 99102

1. Actuator equipped with AM332 potentiometer kit2. Required AM-345 or AE-347

Transmitting Potentiometer

Over 135-1000

For controlling or manually positioning MP type proportional gear train actuators from a potentiometer

AE504

invensys ae504 relay

Order No. Model No.LP20 4024660

PA20 4024698

LIQUID LEVEL CONTROLS

PRE-AMPLIFIER PROBE 1/2" CONNECTION, USE WITH LP20 LEVEL

PROBE

CAPACITANCE LEVEL PROBE 14.6", 1/2"NPT CONNECTION, USE WITH PA20

PRE-AMPLIFIER

Description

The LP20 is a capacitance probe designed for modulating level control in conductive liquids, in conjunction with a PA20 preamplifier, which is supplied separately. It can also be used for adjustable on/off control.

MAXIMUM PRESSURE 464 PSI G

MAXIMUM TEMPERATURE 462ºF

SUPPLY VOLTAGE 14-36 Vdc

____________________________SPIRAX SARCO

LP20

PA20


4

AV-601 VALVE LINKAGE EXTENSION KITELECTRIC/ELECTRONIC

Order No. DescriptionAV601 Used to increase the allowable ambient temperature ratings of MA and MP-5X10 and MP-5X10-XXX

series and MP-541X series actuators on applications with hot water or steam. The MP-541X series of actuators used on valves controlling steam require the AV-601 extension. The kit consists of an extension coupling and a spacer.

invensys AV601 linkage EXTENSION kit

CP-8102 ELECTRONIC TWO INPUT TEMPERATURE OR HUMIDITYCONTROLLERSFOR HEATING, COOLING, HUMIDIFICATION OR DEHUMIDIFICATION IN HVAC SYSTEMSSPECIFICATIONSAuthority ratio adjustment: 0.5:1 through 25:1, adjustable Power supply available: 6.2 Vdc, 7 mA maximumby dial

Control output voltage: 1-15 Vdc, 10 mA maximum Number of controlled devices: Maximum of 6Power requirements: 20 Vdc, 23 mA System 8000

Order No.

Control Dial Range Setpoint "A" & "B"1

Throttling Range for 3Vdc Output Change Construction Sensors

CP8102 20-120oF Adj 2-10oF by Dial2 Self-contained package incorporating an amplifier with two input bridges for 1000 ohm Balco temperature sensors, humidity sensor or remote setpoint adjustor.

Used with single sensor or three sensors.

1 For reset control, set setpoint "B" at zero reset point, setpoint "A" at control point desired with no reset action from sensor "B"

invensys cp8102 controllers

T.A.C. CONTROLS__________________________

VA: 18Input: 10 W

Order No. Model No. Hz) Stroke Length (nominal) Aux Switch DimensionsMA5210 MA-5210 120V 9/16" No 6 3/4" X 3 1/4"MA5213 MA-5213 24V 9/16" No 6 3/4" X 3 1/4"

Order No. Model No.AV600 AV-600AV601 AV-601

AV7600 AV-7600-1

MA SERIES SPRING RETURN ACTUATORSTWO POSITION, OIL IMMERSED - BARBER COLMAN LOGOFor two- position operation of dampers or valves which require the return to normal position upon power interruption.SPECIFICATIONS

Retract on power loss: 15 sec.Actuator electrical ratings:Max output torque extended/retracted: 20 lbs./in.

VALVE LINKAGE ACCESSORIES

Circuit: Two wire

Timing @ 72oF no load stroke: 60 sec.Mounting: Any position

2. Use with AV-600. Consists of extension coupling and spacer.

DescriptionValve linkage for MA-521X1

Valve linkage extension kit for higher temperature fluid applications 2

1.For use with 1/2" to 1 1/4" VB-9XXX, VB111, VB-7XXX valve bodies.

Valve linkage for MA and MP 5000

Order No.AV391AV393

AV390 VALVE LINKAGE KITSComplete kits for assembling electric gear train actuators to VB-9XXX and VB-7XXX valve bodies.

Minimum Actuator Torque Required(Actuator must be

180 lb-in stroke)Stem Force

(lb)40 15070 300


4

T.A.C. CONTROLS__________________________

MP-52XX SERIES PROPORTIONAL, SPRING RETURN ACTUATORSELECTRONIC PROPORTIONAL CONTROL OF VALVES

SPECIFICATIONSPower supply: 20 Vdc, 25 mA Dimensions: 6 3/4"(H) X 3 1/4" DiaInput impedance: 10,000 ohms or greater Controller signal: 2-15 Vdc from System 8000 controllersMounting: upright position preferred Auxilliary switch -500 modeLinkage: Order separately Damper: AM-601 Valve: AV-600Valve bodies: 1/2"-1 1/4" VB-9XXX, VB-111, VB-7XXX valve bodies

Order No.

Supply Voltage 50/60 Hz 10 Rating Output Description Start Point

Positive Positioner1 Extend Retract

Aux. Switch2

10 Amps 120/24

MP5210 120 Vac 22.8 VA Proportional Stroke 9/16" 6 Vdc. Fixed No 60 Sec 40 Sec NoMP5213 24 Vac 23 VA Proportional Stroke 9/16" 6 Vdc. Fixed No 60 Sec 40 Sec No1 Internal feedback circuitry provides positive positioning of the valve stem in relation to the control signal.2 Common of switch in series with AC power supply to the motor. The switch must be wired to control the same voltage as the actuator itself.

For two-position operation of dampers or valves which require the return to normal position upon power interruption

Timing @ 72oF (No Load)

Adj spdt, factory set to close one contact and open the other at retracted end of stroke.

invensys MP-52XX series actuators 6/5/2008

Order No.Output Force

Max. Stroke in

inches Actuator Power Input

Typical Timing in Sec. @ 75º for

1/2" StrokeFeedback

Pot

MF22203 45 lb. 9/1624 Vac, 50/60 Hz, 1.5

VA 126 ± 30 sec. No

MF SERIES ACTUATORS

The MF22XX series floating valve actuators are non-spring return actuators used with floating DDC controllers and standard 1/2 to 2" two-way and three-way globe valve bodies for control of hot water and steam. The DDC controller provides contact or Traic output or SPDT center off (drive open-hold-drive closed).

FLOATING, NON SPRING RETURN VALVE ACTUATORS

__________________________T.A.C. CONTROLS

MP SERIES PROPORTIONAL ACTUATORS

SPECIFICATIONSControl Circuit: Requires spdt switch with neutral or floating position rated at .9A min. @ 24 VacShaft rotation: Reversable proportional can stop at any point in the stroke. Adj. 45-320o except for some modelsAuxiliary switch: Adj. spdt snap-acting, on some models. Factory set to close one contact and open the other at end of CW stroke.Mounting: Upright is preferred.

Order No. Model No. InputTorque Lb./In.

Timing Sec. (No Load) Rot.

Aux. Switch

Spring Return

Built in Trans.

MP381 MP-381 24V, 2.2A @ 60 HZ 220 130 180o spdt No NoMP2150500 MP-2150-500 120V, -/.5A @ 60 HZ 50 25 180o 1 spdt No Yes1 Stroke non-adj.

For floating or proportional controls of dampers, valves and program switches in heating, ventilating and air conditioning applications.

invensys MP series proportional actuators 6/5/2008

MA SERIES TWO-POSITION ACTUATORS

SPECIFICATIONSCircuit: Two-wire No load timing @ 75oF 120 sec.

Shaft rotation: CW 170o when power is applied Dimensions: 5-3/4" (H) x 5-3/8" (W) x 6-9/16" (D)Spring return:

Order No. Power Supply Aux. Switch Running Holding Rated Torque Parallel OppossedMA418 120 Vac @ 60 Hz No 108 VA 42 VA 60 lb./in. 33 sq.ft. 43 sq. ft1 Damper ratings are nominal and based on standard (low low leakage) dampers at 1" WC pressure and 2,000 fpm.

OIL-SUBMERGED, SPRING RETURN

VA Nominal1 Damper Area

CCW to original position when actuator is de-energized

For two-position operation of dampers, valves and other equipment which require the return to normal position upon power interruption

Mounting: Allow 6" clearance above the actuator wiring compartment

INVENSYS MA SERIES Actuators 6/9/2008


4

TC SERIES TWO-POSITION HEATING/COOLING ROOM THERMOSTATS

Order No. TypeSetpoint

Dial Range Differential Electrical Switch Dimensions (HxWxD)TC1191 Single stage,

Single Bulb -40-120oF Heat, 2oF; Neutral,

2oF; Cool, 2oF.

spdt snap action (neutral center)

4-3/8" x 2-7/8" x 1-5/8"

LOW OR LINE VOLTAGE ON-OFF CONTROL OF HEAT/COOL SYSTEMS SUCH AS 3 OR 4 PIPE UNITARY

invensys tc series room thermostats 6/5/2008

\

TP SERIES SINGLE OUTPUT ROOM THERMOSTATSFOR USE IN HEATING AND AIR CONDITIONING SYSTEMSSPECIFICATIONSPower requirements: 20 VdcOutput Voltage: 2-15 Vdc or 15-2 Vdc1

Ambient temperature limits: Mounting: Shipping and storage: --40-160oF Operating: --40-140oF Dimensions: 4 3/8"(H) x 2 3/4"(W) x 1 5/8"(D)

Order No.2 DescriptionRange Temp.

Power Requirements

Power Supply

FACTORY SET. DIRECT-ACTING: JUMPER TERMINAL 4-5;FOR REVERSE-ACTING: JUMPER TERMINAL 4-3TP8101 Single setpoint with single

output signal room controller.55-

85oF.320 Vdc (-1.5/

+1) 13 mA6.2 Vdc 2.2 mA

Max1 Units factory calibration for 7.5 Vdc output with sensor at set point temperature2 Optional cover styles available for TP-810X series only3 Unit dial marked in oF and oC

Throttling Range

2,3,6 and 20oF. Factory set 3oF. by jumper pins

Wall. For panel, order AD-8951 mounting assembly and AD-8953 mounting track

6 System 8000 devices or 2 MP-5200 series actuators

Number of controlled devices:

invensys TP ROOM THERMOSTATS 6/5/2008

Order No. Model No. Device Type Electrical Switch Voltage Vac Full Load Amps Locked Rotor Amps Pilot Duty (VA)

243 -- -- 1001202082404

4. Full load and locked rotor ratings are suitable for hermetic compressors only.

1. Reset cannot be accomplished until the sensed temperature is at least 5oF above setpoint.

720

2. Do not exceed pilot duty rating on one side of switch.3. Less than 0.5 Amp is not recommended.

TC5241 LOW TEMPERATURE THERMOSTATSThe TC-5241 low temperature thermostats are used to control temperature in air conditioning or refrigeration systems. A 20' element senses temperature over a large area. Control responds to coldest one-foot section of the sender. Adjustable setpoint from 35o to 60oF with 5oF fixed differential. Capillary clips are provided.

17 102

TC-5241TC5241 Low temp manual reset1

SPDT2

invensys TC5241 6/9/2008

T.A.C. CONTROLS________________________

Order No. Setpoint Dial Range Throttling Range Amp Rating @ 24 Vac Includes

TP1011 55-85oF. 4oF. 1.0A 44-75oF dial label

TP-1011 PROPORTIONAL ROOM THERMOSTATFor proportional temperature control of electric actuated valves, dampers actuators and sequence controllers. Sensing element is bimetal. Flush or surface mounting.

invensys tp1011 6/12/2008


4

T.A.C. CONTROLS________________________ _________________________T.A.C. CONTROLS

Order No. Model No. Valve size Cv Rating Body Seat Stem Plug Packing DiscVB72130404 VB-7213-0-4-04 1/2" 4.4VB72130406 VB-7213-0-4-06 3/4" 7.5VB72130408 VB-7213-0-4-08 1" 14VB72130409 VB-7213-0-4-09 1 1/4" 20VB72130410 VB-7213-0-4-10 1 1/2" 28VB72130411 VB-7213-0-4-11 2" 40

VB-7213-0-4 SERIES SCREWED NPT 2-WAY VALVES

ANSI Pressure Class (PSIG) 250 (up to 400 PSIG below 150oF)

Material

CompositionSpring Loaded

TFE

NORMALLY OPEN GLOBE VALVES

Bronze BronzeStainless

SteelBrass

invensys vb7213 6/5/2008

Order No. Model No. Valve Size Cv Rating Body Seat Stem Plug Packing Disc

VB72230404 VB-7223-0-4-04 1/2" 4.4

VB72230406 VB-7223-0-4-06 3/4" 7.5

VB72230408 VB-7223-0-4-08 1" 14

VB72230409 VB-7223-0-4-09 1 1/4" 20

Spring Loaded

TFEComposition

Stainless Steel

Bronze Bronze Brass

VB7223 SERIES SCREWED 2-WAY VALVESNORMALLY CLOSED GLOBE VALVESANSI Pressure Class (PSIG) 250 (up to 400 PSIG below 150oF)

Material

invensys vb7223 valves 6/5/2008

Order No. Model No. Valve Size Cv Rating Body and Seat Stem Plug Packing Disc

VB73130404 VB-7313-0-4-04 1/2" 4.4

VB73130406 VB-7313-0-4-06 3/4" 7.5CompositionBronze

Stainless Steel

BrassSpring Loaded

TFE

VB7313 SERIES SCREWED NPT 3-WAY VALVESMIXING GLOBE VALVESANSI Pressure Class (PSIG) 250 (up to 400 PSIG below 150oF)

Material


Order No.Valve Size

Cv Rating Body Seat Stem Plug Packing Disc

VB73120402 1/2" 2.2 Brass Brass SS Brass PTFE None

Material

VB-7312-0-4 SERIES FLARED 3-WAY VALVESMIXING GLOBE VALVESANSI Pressure Class (PSIG) 250

TS SERIES REMOTE TEMPERATURE SENSORSFOR USE IN DUCTS, PLENUM CHAMBERS, LIQUID LINES, TANKS, OUTDOOR AIR, ETC.SPECIFICATIONSSensing element: Temperature-sensitive Balco resistance, 1000 ohms @ 70oF, changes 2.2 ohms per 1oF

Order No. Element EnclosureWiring

ConnectionTS8201 Plate1 1/4" dia. X 6" Long 3 1/2" (H) X 2 1/4" (W) X 2 1/4" (D)

with 2 1/2" extension to element, 1/2" knockouts (bottom)

12" black pigtail leads

1 Immersion requires AT-226 bulb well

DimensionsMounting

Connection

invensys TS series remote temp sensors 6/5/2008


4

Order No. Model No. Valve Size Cv Rating Body and Seat Stem Plug Packing Disc

VB73230406 VB-7323-0-4-06 3/4" 7.5

VB73230408 VB-7323-0-4-08 1" 14

VB7323 SERIES SCREWED NPT 3-WAY VALVESDIVERTING 3-WAY VALVESANSI Pressure Class (PSIG) 250 (up to 400 PSIG below 150oF)

Material

CompositionBronzeStainless

SteelBrass

Spring Loaded

TFE


VALVE PARTS AND ACCESSORIESOrder No. Model No. Description Use With

OYBB289 OYBB-289 Packing gland Nut and Follower Kit 1/2" - 2" valve, VB202,212, 252,804,807

YBA6222 YBA-622-2 Packing assembly with cartridge 1/2"-2" VB90XXXYBA635 YBA-635 Packing assembly (less cartridge) 1/2"-2" VB9XXX

invensys VALVE PARTS & ACCESS 6/9/2008

T.A.C. CONTROLS___________________________

Order No. Replaces Belimo P/NMA407043501 LF24

MS416043 LM24-SR

MS407043 LF24-SR

MA517100000 NoneMA517103100 NoneMS517103140 None

VALVE LINKAGES FOR MOUNTING ABOVE ACTUATORS TO TAC GLOBE VALVES

VALVE LINKAGES Order No. DescriptionAV602AV603AV611

DIRECT COUPLED ACTUATORS

Description

24 Vac, floating signal, 35 in.lb torque, spring return with Auxillary Switch

The DuraDriveTM direct coupled actuators are designed to accept two-position, floating, or proportional control signals from a DDC system or from a thermostat, for control of HVAC applications. The actuators are designed to be used in both damper and valve control applications.

NOTE : A wide variety of TAC Direct Coupled Actuators is available by Special Order. Please call us for technical assistancewith your direct coupled actuator applications..

120Vac, 2 position, SPDT, 105 in.lb torque, spring return

24 Vac,proportional signal, 35 in.lb torque, non-spring return, 0-10 Vdc

24 Vac, proportional signal, 35 in.lb. torque, spring return

Linkage

24Vac, 2 position, SPDT, 105 in.lb. torque, spring return24Vac, Proportional, 6-9 Vdc, 105 in.lb torque, spring

LinkageLinkage

invensys duradrive actuators 6/5/2008


4

Order No. Action Temperature Voltage LeadsOption

IncludedAG13A02A Normally Closed 32 to 200ºF. 24 Vac 18" End SwitchAG13B02A Normally Closed 32 to 200ºF. 120 Vac 18" End SwitchAG13B020 Normally Closed 32 to 200ºF. 120 Vac 18" None

AT33A000 3-wire Floating 32 to 125ºF 24 VacNone-Terminal

Block

Order No. Configuration Size Connection CvVT2213 2-way 1/2" Sweat 3.5VT2223 2-way 1/2" NPT (female) 3.5VT2253 2-way 1/2" SAE Flare 3.5VT2315 2-way 3/4" Sweat 5VT2322 2-way 3/4" NPT (female) 2.5VT2325 2-way 3/4" NPT (female) 5VT2417 2-way 1" Sweat 7.5/8.0VT3213 3-way 1/2" Sweat 4VT3223 3-way 1/2" NPT (female) 4VT3315 3-way 3/4" Sweat 5VT3325 3-way 3/4" NPT(female) 5VT3417 3-way 1" Sweat 8VT3427 3-way 1" NPT(female) 8

REPLACEMENT PART

30118B Motor, 120V/60 Hz

Order No. Configuration Size Connection

VT2322G13B020 2-way 3/4" NPT (female)

POPTOPTM VALVE BODIESPopTopTM valves are designed for two position (on/off) control of fluid flow in a wide variety of heating and cooling applications. They feature brass forged bodies rated at 300 psi, positive 100% shut-off with a easy cleanout plug.

ERIETM POPTOPTM ZONE VALVES & ACTUATORS

The PopTopTM line of motorized hydronic valves provide convenient, reliable and easy installation for a variety of heating and cooling applications. The PopTopTM gives you the same advantages as the Classic Zone Valve and makes installation a snap with easy, one-handed removal or engagement of actuator to valve body. Select one actuator and one valve body to make a complete valve assembly.

GENERAL CLOSE-OFF ACTUATORSThe Pop TopTM series actuators features a synchronous motor designed for long life. They also feature spring return operation and heavy duty gears.

FLOATING NON-SPRING RETURN ACTUATOR

VALVE AND ACTUATOR ASSEMBLYCv

2.5 with 120 Vac N.C. actuator

30118A Motor, 24V/60

TAC erie valves&actuators 7/10/2008

_________________________T.A.C. CONTROLS


4

T.A.C. BARBER-COLMAN PNEUMATICS_______AK POSITIVE POSITIONING PNEUMATIC RELAY

SPECIFICATIONSAir connections: "M" & "B", Barbed for 1/4" OD plastic tubing. "P", Dual-contoured for 1/4" OD and 5/32" OD tubingAir consumption for sizing air compressor: 0.011 scfm @ 20 psig supply.Air capacity for sizing air mains: 20 scimFlow capacity: 860 scim @ 20 psig supply.

Order No. Model No. Input/Output Start Point Span Max. Nom. SupplyAK42309500 AK-42309-500 0 to main air pressure, psig 1-12 psig, adj 2-13 psi, adj 30 psig 15-20 psig

Used to accurately position an actuator stroke with respect to signal pressure from the controller. It can also be used to change the effective spring range of an actuator and increase the capacity of a controller.

Includes: All necessary linkage to assemble AK-42309-500 to MK-2690-0-0-1, 3000, 4600-0-0-2, 4700, 4800, 6900, 7000, 8800 and 8900 actuators.

Caution: AK-42309-500 Positive Positioner cannot be used with MK-556, MK-573, MK-693, MK-2400, MK-2690-0-0-0, MK-4600-0-0-(0,1), MK-11000 and MK-12000 series actuators.

Air Pressure

invensys ak pneumatic relay

AV401 VALVE LINKAGE KITS

Order No. Use with Actuator1 Spring RangeAV401 MK-4602 3-6 psig

MK-4611 5-10 psigMK-4621 10-13 psigMK-4641 3-13 psig

1 Effective area 11 sq. in. Pneumatic actuator is not included with AV-401

For assembling MK-46XX series pneumatic actuators to specific 1/2-2 " Invensys(TAC) valve bodies

invensys AV401 LINKAGE KIT

AV 400 VALVE LINKAGE KITS

Order No. Spring Range Spring ColorAV400 3-7 psig Yellow

5-10 psig Black8-13 psig Blue

For assembling MK-2690 6 sq. in. pneumatic actuator to specific 1/2-1 1/4" Invensys(TAC) valve bodies.

1 Nominal (no load) spring ranges based on 1/2" maximum stroke, provided by AV-400 linkage (order separately).

invensys AV400 LINKAGE KIT

AL-180 SERIES SOLENOID AIR VALVES

SPECIFICATIONSPower consumption: 6.5 W (energized) Humidity: 5-95% RH, non condensingMax. inlet air pressure: 30 psig ConnectionsFlow Capacity: 0.3 scfm @ 15 psig with 1 psig drop Air: Three barbed fittings for 1/4" OD plastic tubingAmbient temperature limits: Electrical: 8" leads on the coilShipping: - 40-150oF Dimensions: 3 3/4"(H) x 3 3/16"(W) x 1 3/8"(D)Operating: 40-130oF

Order No. Type Voltage (AC 60 Hz)AL180 J Box 24AL181 J Box 1201

AL183 J Box 2401 Coils may be changed to convert voltage to 24V/60

For applications where an electrical circuit is used to control a pneumatically operated device. Solenoid air valves are used to direct supply air to a pneumatic device when the coil is energized or de-energized depending on the supply and exhaust air connections.

TAC al-180 series valves


4

CP8551 ELECTRONIC/PNEUMATIC TRANSDUCERSSPECIFICATIONSInput signals: 4-20 mA DC Operating characteristicInput impedance: 500 ohms Linearity: +/- 1% of spanOut signals: 3-15 psig Hysteresis: 0.75% of spanAir supply required:

Ambient operating temp.: - 20-140oFAir consumption1: .008 scfm @ 20 psig supply Humidity: 5-95% RH, noncondensingAir capacity for sizing air mains: 16 scim Air connections: Barbed 1/4" OD plastic tubeMaximum air capacity: 515 sicm

Order No. Model No. Action DescriptionCP8551 CP-8551

Direct acting output pressure rises as input increases

Transducer receives a 4-20 mA input signal and produces a 3-15 psig pneumatic output signal

1 For sizing air compressor.

20 psig nominal, 30 psig max. Clean, dry, oil-free air required.

invensys CP8551 electronic-pneumatic transducers 6/5/2008

K-335 COMPRESSED AIR FILTERS

Order No. Model No. Conn. Size DescriptionK335 K-335 1/4" OD Barb Air flow 0.45 scfm @ 1 psi drop. Maximum operating air pressure:

30 psig. Construction: clear nylon body, borosilicate glass microfiber filter, mineral base oil soluble red dye indicator. Dimensions: 3-1/4" (L) x 1" (dia).

Caution: This filter will not protect or indicate the presence of synthetic paraffin base oils.

In-line air filter used to remove oil and particulates from supply air to a final pneumatic control device. In addition, the filter media turns red if oil is present. Coalescing Filter: 99.99% efficient. Particle Size: 0.1 micron. Aerosol Size: 0.4 micron.

invensys k-335 filter 6/9/2008

_______T.A.C. BARBER-COLMAN PNEUMATICS

MK-2690 VALVE ACTUATORS

SPECIFICATIONSStroke: 1/2" nominalMax. air pressure: 30 psigAir connections: 1/8" FNPTDimensions: 3 5/8"(H) x 4 5/8"(W) x 2 1/4"(D)

Order No. psig kPaMK2690 3-7 psig (yellow) spring 21-48 kPa

5-10 psig (black) spring 34-60 kPa8-13 psig (blue) spring 55-90 kPa

Order No. DescriptionAV430 Valve Linkage Kit

Nominal Spring Range1

1 Nominal (no load) spring ranges based on 1/2" maximum stroke, provided by AV-400 linkage (order separately).

Proportional pneumatic actuator with 6 sq. in. effective area used to control 1/2-2" VB-7XXX (subject to close-off ratings) and VB-9XXX series valves. Mount in any upright position with actuator head above the center line of the valve body.

ACCESSORIES

TAC mk-2690 actuators 7/28/2008


4

T.A.C.BARBER-COLMAN PNEUMATICS_______

Order No.N8000555P

N800 SERIES POSITIVE POSITIONERFor accurate positioning of valve and damper actuators, this positioner utilizes a pilot-operated, relay-type position-sensing mechanism.

DescriptionPlastic positive positioner kit. (includes positioner, feedback arm and 5 and 10 psi feedback springs for M556 (6 in. stroke), M573 (3 in. stroke), and M574 (4 in. stroke).

invensys pneumatic n800 positioner 6/5/2008

PC-100 SERIES PNEUMATIC-ELECTRIC PRESSURE SWITCH

Order No. Mounting Switch Action Scale Range psig psig Pressure PC110 Surface or

TrackSpdt Makes N.O. Contact to Common On Pressure Increase

1-20 1-5 adj; factory set @ 2

50

For on-off control of electrical devices such as air compressors, fans, pilot lights, etc., by the use of a pre-determined air pressure signal

invensys pc100 series SWITCHES 6/9/2008

MK-46XX SERIES VALVE ACTUATORS

SPECIFICATIONSStroke: 1/2" nominal Air connections: 1/8" FNPTMax. air pressure: 30 psig Dimensions: 3 7/8"(H) x 4 3/4"(W) x 4 3/4"(D)Starting point: Adj. +/- 2 psi

Order No. psig kPaMK4601 3-6 21-41MK4611 5-10 34-69MK4621 10-13 69-901 Nominal (no load) spring ranges based on 1/2" maximum stroke.Available: valve linkage AV-401

Nominal Spring Range1

Proportional pneumatic actuator with 11 sq. in. effective diaphragm area used to control 1/2-1 1/4" VB-7XXX and VB-9XXX series valves. Mount in any upright position with actuator head above the center line of the valve body.

actuators invensys mk series valve actuators 6/9/2008

MK-3000 SERIES DAMPER ACTUATORS

SPECIFICATIONSConstruction Air connections: 1/8" FNPT Housing: die cast aluminum Mounting: Diaphragm: Beaded molded neopreneSpring:

Maximum air pressure: 30 psig

Order No.

Nominal Operating

Range (psi)

Starting Pressure (psi)

Nominal Stroke3

Stroke Based on

1.5 psi Pressure to

Actuator

15 psi Supply Dual

Press. System

15 psi Supply Single Press.

System4

20 psi Supply

Single or Dual Press.

System4

15 psi Supply Dual

Press. System

15 psi Supply Single Press.

System4

20 psi Supply

Single or Dual Press.

System4

MK3101 3-8 3(+/-)1 3-1/2, adj 2-4"

12 lbs 44 lbs 56 lbs 96 lbs 21 lbs/in

21 lbs/in 21 lbs/in

MK3121 8-13 8 (+/-)1 3-1/2, adj 2-4"

52 lbs 4 lbs 16 lbs 56 lbs 7 lbs/in 21 lbs/in 21 lbs/in

1 Force and torques based on factory set stroke and starting position2 Nominal torque for actuators without positive positioner is based on 1.5 psi pressure change at the actuator.3 Factory setting required for published operating range.4 Adjust pressure reducing valve so listed pressures are available at the actuator.

Power Stroke

AREA USED TO CONTROL DAMPERS, MIXING BOXES, AIR VALVES, ETC.

Nominal Torque2 Proportional Control1Maximum Force1

In any position. Mounting bracket and connector for 5/16" dia. push rod (MK-3821 and MK4-38XX include clevis for leaf connector) included with actuator.

Retracts actuator shaft on loss of air pressure.

invensys MK3000 ACTUATORS 6/9/2008


4



TK SERIES RELAY BULB THERMOSTATS

SPECIFICATIONS

Sensing element: Remote liquid-filled copper. Maximum: 30 psig

Air connections: 1/8" FNPT for main, branches and 2420001 gauges (not included).

Throttle range: Adj 3-35oF/10 psi change in output, factory set at 5oF.

Output air signal: 0.5 psig to supply air pressure -0.5.Supply air pressure: Clean, oil free, dry air required Capillary length: 6'

Order No. Action Style Dimensions

TK6024 D.A.1 Straight 3/8 x 4-5/8"TK6124 R.A.2 Straight 3/8 x 4-5/8"

2 R.A. (Reverse Acting) decreases output pressure on temperature rise.

For proportional temperature control of pneumatic valves and actuators to maintain air or liquid temperatures in duct, plenum chambers, liquid lines, tanks, etc. May also be used as a low limit thermostat.

Bulb

1 D. A. (Direct Acting) increases output pressure on a temperature rise.

Thermostat: Proportional two pipe type.Thermostats are ambient compensated.Mounting: Upright position on a wall or vertical flat surface.

Control dial range: -20-240oF. Shipped as --20-120oF, reverse side of dial 100-240ºF

invensys tk series bulb thermostat 6/5/2008

Humidity: 10-98% RH, non-condensingSupply air pressure: Clean, oil-free, dry air required. 30 psig max. Mounting: Upright on surface of wall or panelReceiver-controller: Beaded molded neopreneForced balanced pneumatic amplifier.Input signals: 3-15 psig. Max. input pressure 30 psigOutput air signal: 0.5 psig to supply air pressure -0.5 psig

Order No. Description Remote SPA Action1 Type Authority2 Proportional BandRKSR4000 Replacement

single or dual input

+/- 10% of Primary Transmitter Span

D.A/R.A. 2-Pipe 10-200% of Primary (input 1) Transmitter Span Adj.

2-1/2-40% of Primary (input 1) transmitter span Adj.

RKS5001 Replacement Single Input

None D.A/R.A. 1-Pipe None 4-40% of Input Transmitter Span Adj.

2 Primary transmitter connects to input 1.

For use in conjunction with remote proportional transmitters for proportional control of pneumatic actuated dampers, valves, etc. in air conditioning systems. The transmitter-receiver-controller system may be used to control temperature, humidity or pressure

1 D. A. (Direct Acting) factory shipped. Increases output pressure on rise in 1 pressure. Field changeable to R.A./R.A. (Reverse Acting); Decreases output pressure on rise in input 1 pressure.

Setpoint: Adj., oF, oC, in water, mm water, % RH labels (included with controller).

RKS, RKSR SERIES SINGLE/DUAL TRANSMITTER INPUT RECEIVER-CONTROLLER

SPECIFICATIONS

invensys RKS, RKSR RECEIVER-CONTROLLER 6/5/2008

SPECIFICATIONSAction: Direct (increse in output with an increase of pilot pressure).Air pressure Maximum: 30 psig Nominal supply: 15-20 psigAir connections: Barbed for 1/4" OD plastic tubing. No clamps are required.Air consumption for sizing air compressor: 0.016 scfm @ 15 psig and 0.024 scfm @ 20 psig supply.Air capacity for sizing air mains: 40 scim @ 15 psig and 48 scim @ 20 psig supply.Order No. Model No. Description Output Inputs2372502 RS532-H High Pressure Selector Highest of Two Input Pressures 22372501 RS532-L Low Pressure Selector Lowest of Two Input Pressures 2

RS532/2372 SERIES PNEUMATIC PRESSURE SELECTORS

invensys RS532 Series pneumatic press selector


4Order No. Description

2360501 Connections marked M(main), B(branch), and S1(input signal)

PNEUMODULAR® REVERSING RELAYThe branch line pressure on the reversing relay decreases in direct proportion to an increase in input signal pressure and also amplifies the volume of air available for the final control devices, thereby minimizing system lag.

invensys pneu 2360 relay 6/5/2008

Order No. Description Port Connected toM Main air or input signal no. 2B Branch outputS1 Input signal no. 1B OutputS1 Input Signal no. 1S2 Input Signal no. 2

PNEUMODULAR® VOLUME BOOSTER/PRESSURE y p p g g p yapplication requires amplifying the volume of control air to final control devices. The relay may also be used as a low pressure selector. The high pressure selector relay is a device designed for use in pneumatic control systems where the application requires the comparison, selection, and transmission of the higher of two proportional input signals.

Port Connections

High pressure selector; NOT for use with "restricted" signals (use R432-2)

2372501

2372502

Volume booster or low pressure selector

invensys pneumodular volume booster pressure selector 6/5/2008


Order No. Action2341521 Direct2341522 Reverse

Includes the Receiver-Controller and two gauge fittings mounted on the base.

PNEUMODULAR® RECEIVER CONTROLLERThe receiver controllers are used with remote pneumatic transmitters to provide proportional control in pneumatic control systems. They may also be used with any pneumatic device having an output of 3 to 15 psig. The receiver controllers are dual input, but may be used as single input by using only the desired input.

Description

invensys 2341 reccntrs 6/5/2008

TK, TKR SINGLE SETPOINT ROOM THERMOSTATS

SPECIFICATIONS

30 psig max.

Order No. Application Type Thermostat Control Dial Range1 Supply Pressure & Control Action2

TK1001 Heating and/or cooling 2-pipe, relay type 55-85F Direct acting 15 or 20 psiTKR1001 Heating and/or cooling 2-pipe, relay type 55-85F Direct acting 15 or 20 psiTKR1101 Heating and/or cooling 2-pipe, relay type 55-85F Reverse acting 15 or 20 psiTKR50013 Heating and/or cooling 1-pipe, bleed type 55-85F Direct acting

1 Dial stops pins included to limit dual range on all units.2 D. A. (Direct Acting) increases output pressure on a temperature rise. R.A. (Reverse Acting) decreases output pressure on temperature rise.

Order No. DescriptionAT111 Replacement Kit fittings

ACCESSORY

For proportional temperature control of pneumatic actuated valves and damper actuators to maintain room air temperatures in heating, ventilating and air conditioning systems. Bi-metal sensing element.

3REstat kit. Includes cover, mounting plate and installation parts.

Output air signal: 0.5 psig to supply air pressure - 0.5.Supply air pressure: Clean, oil free, dry air required.

TAC tk,TKR ROOM thermostat 7/28/2008


4


Order No. Replaced By1,2 Dial Range Air Consumption Description2211512 2211012 55-85oF 0.017 scfm Single temperature, one-pipe, direct acting; includes thermostat,

cover and conversion kit.2211513 2211013 55-85oF 0.017 scfm Single temperture, one-pipe, reverse acting; Replacement does

not include conversion kit.2212118 Active 55-85oF 0.009 scfm Single temperature, two-pipe, direct acting; throttling adjustable

o2212128 2212118 55-85oF 0.009 scfm Single temperature, two-pipe, direct acting; throttling range

adjustable 2o-12oF2212418 2212118 55-85oF 0.009 scfm Replacement does not include wall mounting kit.

2298060 Active 65-85oF 0.017 scfm RA at 16 psi, DA at 25 psi, includes cover and remote sensor; Temperature Controller

2298063 Active 65-85oF 0.017 scfm DA at 16 psi, RA at 25 psi, includes cover and remote sensor; Temperature Controller

PNEUMATIC ROOM THERMOSTATS AND TEMPERATURE CONTROLLERSThese pneumatic room thermostats are designed for proportional temperature control of pneumatic valves and damper actuators in heating, ventilating, and air conditioning systems. They feature a small size and are factory calibrated.

1 Thermostat with plastic thermostat cover, adjustment cover, standard cover, standard mounting plate, and mounting screws. Replacement does not include dial stops. Dial Stop Kit 20-712 should be ordered.2 If you require additional components to mount thermostats to drywall with holes greater than 5/8", the Universal Mounting Kit is required.

invensys pneu tstats 6/9/2008

FEATURES:

PNEUMODULAR® MULTI-INPUT HIGH AND LOW SELECTOR RELAYThe selector relay is a device designed for use in pneumatic control systems where the application requires the comparison, selection, and transmission of the highest and/or the lowest of up to six pneumatic input signals. All input ports are "dead-ended" and no signal passes through the relay to the output ports.

Order No.Port Connections

Port Connected to:

*Six-input high and low pressure selector. Requires main air connection.*Highest of 6 inputs is output at Port H.

Input signals

*Lowest of 6 inputs is output at Port L.

2373501 MLH

1 through 6

Main airLowest branch outputHighest branch output

TAC multi-input selector relay 8/26/2008

_T.A.C. BARBER-COLMAN PNEUMATIC PARTS

Order No. Range (non-adjustable) Span Mounting Sensing Element Description

2252252 0-100oF 100oF Duct Rigid (coiled) element, 10" long2252655 --25-125oF 100oF Duct or outdoor air 10 1/2" X 1/4" bulb with 9' capillary2252703 --40-160oF 200oF Duct or outdoor air 1/4" X 2 1/2" bulb with 42" capillary

DUCT, IMMERSION AND OUTDOOR-AIR TEMPERATURE These pneumatic temperature transmitters are designed to measure air or fluid temperatures in pneumatic control systems and transmit a fixed span, 3 to 15# signal to controlling and indicating devices. These transmitters are one-pipe devices requiring an externally restricted source of constant pressure control air.

invensys pneu transmittors 6/9/2008


PNEUMATIC ACTUATOR PARTS Order No. Description Use With

N8009423 Diaphragm M573N8009424 Diaphragm M574PND0021 Diaphragm MK3XXX seriesPNV1021 Diaphragm MK690, MK2400, AL161-4PNV2 Diaphragm MK-4XXXPNV202 Diaphragm MK6600, 6700,6800,6900,8800,8900 series

TAC ACTUATOR PARTS & ACCESS


4

T.A.C. BARBER-COLMAN ACCESSORIES______

BARB FITTINGSPNEUMATIC AIR SUPPLY

Order No. Description Std. Pack Order No. Description Std. PackMALE ADAPTORS BARB PLUGB1311 1/4" or 5/32" x 1/8" MPT 100 B391 1/4" Plug 100B132 1/4" x 1/8" MPT 100 B392 3/8" Plug 100B133 3/8" x 1/8" MPT 100 BARB TO MPT 90 DEG ELLFEMALE ADAPTER B571 1/4" x 1/8" MPT 100B135 1/4" x 1/8" FPT 100 BARB 90 DEG ELLCOUPLINGS B573 1/4" x 1/4" 100B260 5/32" x 5/32" 100 B574 3/8" x 3/8" 100B261 1/4" x 5/32" 100

B263 1/4" x 1/4" 100 (L X R X B)B264 3/8" x 3/8" 50B265 3/8" x 1/4" 50FEMALE BRANCH TEEB373 1/4" x 1/8" FPT 100BARB TEESB374 5/32" x 5/32" x 5/32" 100B376 1/4" x 1/4" x 1/4" 100B377 3/8" x 3/8" x 1/4" 100B378 3/8" x 3/8" x 3/8" 100

B137BARB TO COMPRESSION ADAPTOR

1/4" Barb X 1/4" Compression

Note: When ordering tees, fitting size reads left to right to branch

TAC BARB FITTINGS

PNEUMATIC RESTRICTORS Order No. Description Application

21153 In-line restrictor, 1.0 scfh at 20 psig. One pipe thermostats

invensys pneumatic restrictors 6/5/2008

Order No. Item No. DescriptionAT528 130 Clamp Plate

131 Gasket132 Gasket133 Restrictor Plate134 Aspirating Tube146 Aspirating Restrictor Cup84 Screw

147 Screw1064 3/16" Tygothane Tubing Assembly

PILOT RESTRICTOR KIT FOR NON-ASPIRATED THERMOSTATS & MISC. ACCESSORIES

Set Contents

Pilot restrictor kit for TK1XXX pneumatic thermostats1.

1 Except -600 models.

invensys pilot restrictor kit 6/9/2008

T.A.C.BARBER-COLMAN PNEUMATIC PARTS__


4

T.A.C.BARBER-COLMAN PNEUMATIC PARTS__

____________________________T.A.C./POTTER

Order No.Model No. Cover Contacts

For Pipe Sizes

9000002 PTR-IFS-2 Nema 1 2 spdt 1" - 8"9000005 PTR-IFS-WP-1 Nema 4 1 spdt 1" - 8"

POTTER FLOW SWITCHESVANE TYPE FLOW SWITCHES FOR NON-HAZARDOUS FLUIDS

TOOL SERIES CALIBRATION TOOLS AND KITSOrder No. Model No. Description

TOOL201 TOOL-020 Packing wrench for VB-111, VB-121, VB-131, VB-151, VB-314, VB-324, VB-334, VB-354, VP-9XXX.TOOL82 TOOL-082 Pocket wrench with 5/64" Allen wrench for branch test port on pneumatic thermostats and locking

cover screws and .048" 6-spline wrench for thermostat calibration.TOOL95 TOOL-095-1 Pneumatic calibration tool kit. Calibrates all Invensys pneumatic equipment. 1

20881 20-881 Thermostat calibration wrench.22138 22-138 Gage adapter2420001 2420-001 1 1/2" gauge, 0-30#, 1/8" MNPT back connectJC5216 TOOL-85 Pressure bulb used to simulate pressures in pneumatic air lines.1Includes: MCS-GA gauge adaptor, N2-4 2 X 2, 1/16" hexhead thermostat calibration cover screw wrench, TOOL-10 magnetic screwdriver, female branch tee (1/4" barb x 1/4" barb x 1/8" FPT), TOOL-11 calibration wrench, TOOL-69 calibration & cover screw wrench for TK-9X01, TOOL-70 needle probe for TK-9X01, TOOL-78 adaptor, TOOL-80 chjangeover wrench, TOOL-82 combination wrench, TOOL-83 mullion thermostat calibration wrench, TOOL-85 manual hand pump, TOOL-87 needle and adaptor, TOOL-110 3/32" hex wrench, AL-361 0-30 psi gauge, air line tubing for barbed fitting, air line tubing with compression fitting, 3/16" x 4" blade screwdriver.

invensys TOOLS AND KITS 6/9/2008

PNEUMATIC PLASTIC/COPPER TUBINGOrder No. Dimensions Roll Length Description

PLASTICT100 5/32" OD x .030" wall 500' Fire resistant (FR) polyethylene tubing.T1002 5/32" OD x .030" wall

500'Fire resistant (FR) polyethylene "twin" tubing (2 tubes extruded together).

T101 1/4" OD x .030" wall 250' Fire resistant (FR) polyethylene tubing.T1012 1/4" OD x .030" wall 250' Fire resistant (FR) polyethylene "twin"

tubing (2 tubes extruded together).T110 3/8" OD x .062 wall 250' Fire resistant (FR) polyethylene tubing.COPPERCCONTU-2X025 1/8" NOM X .025 20 FT JT Control tubing, straight lengths

invensys pneumatic tubing 6/9/2008

______T.A.C. BARBER-COLMAN ACCESSORIES


4

TECO WESTINGHOUSE______________________

Drives engineered for HIGH PERFORMANCE.Flexible, low-cost, and reliable – TECO-Westinghouse drives and controls offer an ex-tensive line of products that you can trust and depend on. Teco-Westinghouse offers a complete line of drives to meet any application you have. We are featuring two of the most commonly used models.

MA7200 GENERAL PURPOSE DRIVE VOLTAGE RANGE 230V _______40 HP 460V _____________75HP FEATURES

General Purpose AC Drive Sensorless Vector, V/Hz and

PG Feedback Control NEMA 1 Enclosure

230V, 50/60Hz,3-Phase from 1 – 40 HP 460V, 50/60Hz,3-Phase from 1 - 75 HP

NEMA 4/12 Enclosure 230V, 50/60Hz, 3 - Phase from 1 – 20 HP 460V, 50/60Hz, 3 - Phase from 1 – 20 HP

English LCD Display/ Copy Unit Modbus Communication (Built-in) Profibus Communication (Optional) PG Feedback (Built-in) PID Control Simple PLC Function Timer Function Energy Savings Function MA Link Software UL, cUL, and CE Approved

Applications

HVAC Wood/Lumber Mixing Compressors Extrusion Conveyors

The MA is Teco Westinghouse’s most versatile drive. It is capable of controlling virtually every application using its adaptive software.

PA7300 FAN & PUMP DRIVE VOLTAGE RANGE 230V ________125 HP 400V _____________________500HP 575V _______100 HP FEATURES

Designed for Variable Torque Applications

208V, 50/60Hz, 3 – Phase from 5 – 100 HP 230V, 50/60Hz, 3 – Phase from 5 – 125HP 460V, 50/60Hz, 3 – Phase from 5 – 500HP 575V, 50/60Hz, 3 – Phase from 5 – 100HP PID & Auto Energy Savings Functions PID Sleep Mode Function 2 Line English Language LCD Keypad /

Copy Unit Communication Options

Metasys N2, Lon Works, Profibus, Others PA Link Software UL, cUL, CE Approved

Applications

Fans Pumps Refrigeration Waste Water Chillers

The PA is designed specifically for the HVAC market. Built-in HVAC/R software is designed with today’s demanding requirements.


4

TECO WESTINGHOUSE______________________

___________________________________WEISS4CTS SERIES HVAC PRESSURE GAUGES

Order No. Dial Size Type Size Pressure Range Bourdon Tube Material

4CTS15 4-1/2" Lower conn 1/4" 0/15 PSI Brass4CTS30 4-1/2" Lower conn 1/4" 0/30 PSI Brass4CTS60 4-1/2" Lower conn 1/4" 0/60 PSI Brass4CTS100 4-1/2" Lower conn 1/4" 0/100 PSI Brass4CTS160 4-1/2" Lower conn 1/4" 0/160 PSI Brass4CTS200 4-1/2" Lower conn 1/4" 0/200 PSI Brass4CTS300 4-1/2" Lower conn 1/4" 0/300 PSI Brass4CTS600 4-1/2" Lower conn 1/4" 0/600 PSI Brass4CTSV 4-1/2" Lower conn 1/4" 30"/0 VAC Brass4CTSVP30 4-1/2" Lower conn 1/4" 30" X 30 PSI Brass4CTSVP100 4-1/2" Lower conn 1/4" 30"x100PSI Brass

Connection

Meets the requirements and needs of contractors in heating, plumbing, air conditioning and ventilating and all equipment manufacturers in these fields. They are intended for general service conditions, for pressure or vacuum on air, oil, water, gas or other mediums that do not attack brass. Accuracy: 1% middle half, 2% remainder, ANSI, B40.1, grade A.

WEISS 4CTS SERIES PRESSURE GAUGES 7/16/2008

DRY/LIQUID FILLED GAUGES, STAINLESS STEEL CASE

Order No. Model No. Dial Size Type Size Pressure Range Bourdon Tube Material

LIQUID FILLED GAUGES LF25BR15L4 LF25S-1 2-1/2 LOWER 1/4 0/15 psi BronzeLF25BR30L4 LF25S-1 2-1/2 LOWER 1/4 0/30 psi BronzeLF25BR60L4 LF25S-1 2-1/2 LOWER 1/4 0/60 psi BronzeLF25BR100B4 LF25S-1 2-1/2 BACK 1/4 0/100 psi BronzeLF25BR100L4 LF25S-1 2-1/2 LOWER 1/4 0/100 psi BronzeLF25BR160L4 LF25S-1 2-1/2 LOWER 1/4 0/160 psi BronzeLF25BR200B4 LF25S-1 2-1/2 BACK 1/4 0/200 psi BronzeLF25BR200L4 LF25S-1 2-1/2 LOWER 1/4 0/200 psi BronzeLF25BR300L4 LF25S-1 2-1/2 LOWER 1/4 0/300 psi BronzeLF25SS30L4 LF25S-2 2-1/2 LOWER 1/4 0/30 psi Stainless steelLF25SS60L4 LF25S-2 2-1/2 LOWER 1/4 0/60 psi Stainless steelLF25SS100L4 LF25S-2 2-1/2 LOWER 1/4 0/100 psi Stainless steelLF25SS160L4 LF25S-2 2-1/2 LOWER 1/4 0/160 psi Stainless steelLF25SS200L4 LF25S-2 2-1/2 LOWER 1/4 0/200 psi Stainless steelLF25SS300L4 LF25S-2 2-1/2 LOWER 1/4 0/300 psi Stainless steelLF25SS400L4 LF25S-2 2-1/2 LOWER 1/4 0/400 psi Stainless steelCOMPOUND GAUGESLF25BR15CL4 LF25S-1 2-1/2 LOWER 1/4 30"X15 psi BronzeLF25BR30CL4 LF25S-1 2-1/2 LOWER 1/4 30"X30 psi BronzeLF25BR100CL4 LF25S-1 2-1/2 LOWER 1/4 30"X100 psi BronzeVACUUM GAUGESLF25BRVL4 LF25S-1 2-1/2 LOWER 1/4 30"/0 vac BronzeLF25SSVL4 LF25S-2 2-1/2 LOWER 1/4 30"/0 vac Stainless steelDRY GAUGES

NF25SS30CL4 NF255-S 2-1/2 LOWER 1/4"30 psi x 30" Hg

Compound Stainless steelNF25SS30L4 NF25S-2 2-1/2 LOWER 1/4 0/30 psi Stainless steelNF25SS60L4 NF25S-2 2/1/2002 LOWER 1/4" 0/60 psi Stainless steelNF25SS100L4 NF25S-2 2-1/2 LOWER 1/4 0/100 psi Stainless steelNF25SS160L4 NF25S-2 2/1/2002 LOWER 1/4" 0/160 psi Stainless steelNF25SS200L4 NF25S-2 2-1/2 LOWER 1/4 0/200 psi Stainless steelNF25SS300L4 NF25S-2 2-1/2 LOWER 1/4 0/300 psi Stainless steel

PROCESS GAUGES

NF4UGBR30L4 NF4UGY-1 4-1/2 LOWER 1/4 0/30 psi BronzeNF4UGBR100L4 NF4UGY-1 4-1/2 LOWER 1/4 0/100 psi BronzeNF4UGBR200L4 NF4UGY-1 4-1/2 LOWER 1/4 0/200 psi BronzeNF4UGBR300L4 NF4UGY-1 4-1/2 LOWER 1/4 0/300 psi BronzeNF4UGS60L4 NF4UGY-2 4-1/2 LOWER 1/4 0/60 psi Stainless SteelNF4UGS100L4 NF4UGY-2 4-1/2" LOWER 1/4 0/100 psi Stainless SteelNF4UGS160L4 NF4UGY-2 4-1/2 LOWER 1/4 0/160 psi Stainless Steel

Connection

Industrial stainless steel case, phosphor bronze or stainless steel "C-Tube", 2-1/2" gauge accuracy 1.6% of span, clear acrylic or glass window. Liquid flled gauges ideal for service with vibration present. Dry gauge is recommended for steam and other high temperature services (always use gauge syphon on steam service).

Ideal for precise requirements of process, industrial, power and chemical industries. Process gauges with phenolic case, phosphor bronze or stainless steel "C-Tube", glass window, 0.5 accuracy. Conforms to ANSI/ASME standard B40.1 grade 2A

WEISS LIQUID FILL GAUGES 9/8/2008


4

WEISS____________________________________

TL SERIES UTILITY PRESSURE GAUGES

Order No. Model No. Dial Size Type Size Pressure Range CommentsTL15P30B2 TL15P1/8CBM3 1-1/2" Center Back 1/8" 0/30 psiTL15P200L2 TL15P1/8LM20 1-1/2" Lower 1/8" 0/200 psiTL20P30B2 TL20P1/8CBM3 2" Center Back 1/8" 0/30 psiTL20VL4 TL20V1/4LM 2" Lower 1/4" 30" VACTL20P60L4 TL20P1/4LM60 2" Lower 1/4" 0/60 psiTL20PU60B2 TL20PU1/8CBM 2" Center Back 1/8" 0/60 psi Panel MountTL20P100B4 TL20P1/4CBM1 2" Center Back 1/4" 0/100 psiTL20P100L4 TL20P1/4LM10 2" Lower 1/4" 0/100 psiTL20P160B2 TL20P1/8CBM1 2" Center Back 1/8" 0/160 psiTL20P160B4 TL20P1/4CBM1 2" Center Back 1/4" 0/160 psiTL20P200L4 TL20P1/4LM20 2" Lower 1/4" 0/200 psiTL25P15L4 TL25P1/4LM15 2-1/2" Lower 1/4" 0/15 psiTL25P30L4 TL25P1/4LM30 2-1/2" Lower 1/4" 0/30 psiTL25P60L4 TL25P1/4LM60 2-1/2" Lower 1/4" 0/60 psiTL25P100B4 TL25P1/4CBM4 2-1/2" Center Back 1/4" 0/100 psiTL25P100L4 TL25P1/4LM10 2-1/2" Lower 1/4" 0/100 psiTL25P160B2 TL25P1/8CBM1 2-1/2" Center Back 1/8" 0/160 psiTL25P160L4 TL25P1/4LM16 2-1/2" Lower 1/4" 0/160 psiTL25P200B2 TL25P1/8CBM2 2-1/2" Center Back 1/8" 0/200 psiTL25P200L4 TL25P1/4LM20 2-1/2" Lower 1/4" 0/200 psiTL25P300L4 TL25P1/4LM30 2-1/2" Lower 1/4" 0/300 psiTL25VP30L4 TL25VP1/4LM3 2-1/2" Lower 1/4" 30" X 30 psiTL25VP60L4 TL25VP1/4LM3 2-1/2" Lower 1/4" 30" X 60 psiTL35P30L4 TL35P1/4LM30 3-1/2" Lower 1/4" 0/30 psiTL35P60L4 TL35P1/4LM60 3-1/2" Lower 1/4" 0/60 psiTL35P100L4 TL35P1/4LM10 3-1/2" Lower 1/4" 0/100 psiTL35P160L4 TL35P1/4LM16 3-1/2" Lower 1/4" 0/160 psiTL35P200L4 TL35P1/4LM20 3-1/2" Lower 1/4" 0/200 psiTL35P300L4 TL35P1/4LM30 3-1/2" Lower 1/4" 0/300 psiTL35VP60L4 TL35VP1/4LM3 3-1/2" Lower 1/4" 30" X 60 psi

Connection

General service gauges, bronze bourdon tube, brass socket. Accuracy 2% of middle 1/3 of range. ANSI/ASME B40.1 Grade B.

WEISS TL SERIES PRESSURE GAUGES 7/28/2008

LOW PRESSURE DIAPHRAGM GAUGES

Order No. Dial Size Type Size Pressure RangeDG25C20OZL4 2-1/2" Lower 1/4" 20 oz X 35"DG25C9OZL4 2-1/2" Lower 1/4" 9 oz X 15" wcDG25P30OZL4 2-1/2" Lower 1/4" 0/30 ozDG25P5L4 2-1/2" Lower 1/4" 0/5 psi

Connection

Designed for pressures below 10 psi. These gauges offer an instrument highly sensitive yet durably constructed. Accuracy 1.5% of full scale range.

WEISS low press diaphg gauges 7/29/2008

AMMONIA PRESSURE GAUGES

Order No. Dial Size Type Size Pressure Range Bourdon Tube MaterialMG35-300 3-1/2" LC 1/4" 300/VAC 316SS

Connection

READS IN BOTH PSI AND CORRESPONDING AMMONIA TEMPERATURE

WEISS AMMONIA PRESSURE GAUGES 7/28/2008

DRY/LIQUID FILLED GAUGES, STAINLESS STEEL CASE


LIQUID FILLED GAUGES LF25BR15L4 LF25S-1 2-1/2 LOWER 1/4 0/15 psi BronzeLF25BR30L4 LF25S-1 2-1/2 LOWER 1/4 0/30 psi BronzeLF25BR60L4 LF25S-1 2-1/2 LOWER 1/4 0/60 psi BronzeLF25BR100B4 LF25S-1 2-1/2 BACK 1/4 0/100 psi BronzeLF25BR100L4 LF25S-1 2-1/2 LOWER 1/4 0/100 psi BronzeLF25BR160L4 LF25S-1 2-1/2 LOWER 1/4 0/160 psi BronzeLF25BR200B4 LF25S-1 2-1/2 BACK 1/4 0/200 psi BronzeLF25BR200L4 LF25S-1 2-1/2 LOWER 1/4 0/200 psi BronzeLF25BR300L4 LF25S-1 2-1/2 LOWER 1/4 0/300 psi BronzeLF25SS30L4 LF25S-2 2-1/2 LOWER 1/4 0/30 psi Stainless steelLF25SS60L4 LF25S-2 2-1/2 LOWER 1/4 0/60 psi Stainless steelLF25SS100L4 LF25S-2 2-1/2 LOWER 1/4 0/100 psi Stainless steelLF25SS160L4 LF25S-2 2-1/2 LOWER 1/4 0/160 psi Stainless steelLF25SS200L4 LF25S-2 2-1/2 LOWER 1/4 0/200 psi Stainless steelLF25SS300L4 LF25S-2 2-1/2 LOWER 1/4 0/300 psi Stainless steelLF25SS400L4 LF25S-2 2-1/2 LOWER 1/4 0/400 psi Stainless steelCOMPOUND GAUGESLF25BR15CL4 LF25S-1 2-1/2 LOWER 1/4 30"X15 psi BronzeLF25BR30CL4 LF25S-1 2-1/2 LOWER 1/4 30"X30 psi BronzeLF25BR100CL4 LF25S-1 2-1/2 LOWER 1/4 30"X100 psi BronzeVACUUM GAUGESLF25BRVL4 LF25S-1 2-1/2 LOWER 1/4 30"/0 vac BronzeLF25SSVL4 LF25S-2 2-1/2 LOWER 1/4 30"/0 vac Stainless steelDRY GAUGES

NF25SS30CL4 NF255-S 2-1/2 LOWER 1/4"30 psi x 30" Hg

Compound Stainless steelNF25SS30L4 NF25S-2 2-1/2 LOWER 1/4 0/30 psi Stainless steelNF25SS60L4 NF25S-2 2/1/2002 LOWER 1/4" 0/60 psi Stainless steelNF25SS100L4 NF25S-2 2-1/2 LOWER 1/4 0/100 psi Stainless steelNF25SS160L4 NF25S-2 2/1/2002 LOWER 1/4" 0/160 psi Stainless steelNF25SS200L4 NF25S-2 2-1/2 LOWER 1/4 0/200 psi Stainless steelNF25SS300L4 NF25S-2 2-1/2 LOWER 1/4 0/300 psi Stainless steel

PROCESS GAUGES

NF4UGBR30L4 NF4UGY-1 4-1/2 LOWER 1/4 0/30 psi BronzeNF4UGBR100L4 NF4UGY-1 4-1/2 LOWER 1/4 0/100 psi BronzeNF4UGBR200L4 NF4UGY-1 4-1/2 LOWER 1/4 0/200 psi BronzeNF4UGBR300L4 NF4UGY-1 4-1/2 LOWER 1/4 0/300 psi BronzeNF4UGS60L4 NF4UGY-2 4-1/2 LOWER 1/4 0/60 psi Stainless SteelNF4UGS100L4 NF4UGY-2 4-1/2" LOWER 1/4 0/100 psi Stainless SteelNF4UGS160L4 NF4UGY-2 4-1/2 LOWER 1/4 0/160 psi Stainless Steel

Connection

Industrial stainless steel case, phosphor bronze or stainless steel "C-Tube", 2-1/2" gauge accuracy 1.6% of span, clear acrylic or glass window. Liquid flled gauges ideal for service with vibration present. Dry gauge is recommended for steam and other high temperature services (always use gauge syphon on steam service).

Ideal for precise requirements of process, industrial, power and chemical industries. Process gauges with phenolic case, phosphor bronze or stainless steel "C-Tube", glass window, 0.5 accuracy. Conforms to ANSI/ASME standard B40.1 grade 2A

WEISS LIQUID FILL GAUGES 9/8/2008


4

WEISS____________________________________ ____________________________________WEISS

BIMETAL DIAL THERMOMETERS

Order No. Dial Size Type Size Stem Length Temperature Range

2BM4200 2 REAR 1/4 4 0/200oF3BMS25250 3 LOWER 1/2 2-1/2 0/250oF3BMS4130 3 LOWER 1/2 4 30/130oF3BMS4200 3 LOWER 1/2 4 0/200oF3BMS4250 3 LOWER 1/2 4 0/250oF3BM25120 3 REAR 1/2 2-1/2 20/120oF3BM25130 3 REAR 1/2 2-1/2 30/130oF3BM25200 3 REAR 1/2 2-1/2 0/200oF3BM25250 3 REAR 1/2 2-1/2 0/250oF3BM25300 3 REAR 1/2 2-1/2 50/300oF3BM25400 3 REAR 1/2 2-1/2 50/400oF3BM25550 3 REAR 1/2 2-1/2 50/550oF3BM41000 3 REAR 1/2 4 200/1000oF3BM4120 3 REAR 1/2 4 20/120oF3BM4130 3 REAR 1/2 4 30/130oF3BM4200 3 REAR 1/2 4 0/200oF3BM4250 3 REAR 1/2 4 0/250oF3BM4300 3 REAR 1/2 4 50/300oF3BM4400 3 REAR 1/2 4 50/400oF3BM4550 3 REAR 1/2 4 50/550oF3BM61000 3 REAR 1/2 6 200/1000oF3BM6120 3 REAR 1/2 6 20/120oF3BM6130 3 REAR 1/2 6 30/130oF3BM6200 3 REAR 1/2 6 0/200oF3BM6250 3 REAR 1/2 6 0/250oF3BM6550 3 REAR 1/2 6 50/550oF3BM12200 3 REAR 1/2 12 0/200oF

Connection

Type 304 SS case assembly, hermetically sealed to prevent entry of moisture, glass face, accurate within 1% of scale range. Available with lower or rear connections with varied stem lengths. Manufacturer suggests using a socket well .For wells, see Well Tech section, page 205.

WEISS BIMETAL dial thermometers

TRI-O-METER GAUGES


40TP200B-8 HTP40RSX 3-1/4" Back 1/2" 200 psi, 100/290oF Bronze40TP200L-8 HTP40L 3-1/4" Lower 1/2" 200 psi, 100/290oF Bronze40TP55B-8 CTP40RSX 3-1/4" Back 1/2" 75 psi, 20/220oF Bronze40TP55L-8 CTP40L 3-1/4" Lower 1/2" 75 psi, 20/220oF Bronze

Connection

The Weiss Tri-o-meter is designed for use on all types of hot water heating systems. One instrument reads the water pressure, water temperature and system head in feet of H2O.

WEISS 30tp tri-gauges 7/29/2008

BIMETAL RECALIBRATION THERMOMETERS

Order No. Dial Size Type Size Stem Length Temperature Range

3RBM25120 3" Rear 1/2" 2-1/2" --20-120oF3RBM25200 3" Rear 1/2" 2-1/2" 0-200oF

Connection

WEISS BIMETAL recal thermometers


4

For more Weiss information, go to www.weissinstruments.com.

WEISS____________________________________DIGITAL VARIABLE ANGLE THERMOMETERS

Order No. Model No. Stem LengthDVBM25 DVBM25 2-1/2"DVBM4 DVBM4 4"DVBM6 DVBM6 6"DVU35 DVU35 3-1/2"DVU6 DVU6 6"

WELLS (for above)Order No. Model No. Use With Connection MaterialE35-75BS E35-75BS DVU35 3/4" BrassER6-75BS ER6-75BS DVU6 3/4" BrassBRSW-8X025 100031A DVBM25 1/2" BrassBRSW-12X025 100032A DVBM25 3/4" BrassBRSW-8X040 105051A DVBM4 1/2" BrassBRSW-12X040 105052A DVBM4 3/4" BrassBRSW-8X060 110091A DVBM6 1/2" BrassBRSW-12X060 110092A DVBM6 3/4" BrassSSW-8X025 100031C DVBM25 1/2" Stainless SteelSSW-8X040 105051C DVBM4 1/2" Stainless SteelSSW-8X060 110091C DVBM6 1/2" Stainless Steel

DVBM series fit the standard well for Bi-Metal thermometers. DVU series fit standard well for the Ind Scale thermometers. Thermometers are vari-angle and can replace either lower or back mount. Range -50/300oF. No batteries needed. Can operate in low light levels. Accuracy 1%

WEISS DIGITAL VARI-ANGLE therm 7/29/2008

REMOTE READING DIGITAL THERMOMETERS

Order No. Model No. Temp Range Cap

56SD-230 56SD-160 --40/230oF 5 ft

Lexan 2.25" square flange to fit std 2" round panel hole dia. 3/8" LCD digits. 3V Solar Cell provides power. 15 second update time.

WEISS REMOTE READ digital thermometer 7/29/2008

HOT WATER THERMOMETERS

Order No. Model No. Scale Size Type Size Stem Length Temperature Range

HW5A2 22200 5" Angle 1.2" 2" 40-260oFHW5S2 22210 5" Straight 1/2" 2" 40-260oF

Connection

Trade line thermometers intended for small pipeline applications, fixed stems in a straight or angle form suitable for chilled or hot water installations. 5" scale, 2" stem, 1/2" NPT brass socket.

VARIABLE ANGLE THERMOMETERS

Order No. Model No. Scale Size Stem Length Temp Range Size

9VU35120 9VU35-120 9 3-1/2 0-120oF9VU35240 9VU35-240 9 3-1/2 30-240oF9VU6120 9VU6-120 9 6 0-120oF9VU6160 9VU6-160 9 6 0-160ºF9VU6240 9VU6-240 9 6 30-240oFWells for Variable Angle ThermometersE35-75BS E35-75BS 3-1/2" 3/4"EN6-75BS EN6-75BS 6" 3/4"ER6-75BS ER6-75BS 6" 3/4"Note: well "EN' is with lag.

Red reading, mercury filled thermometer, molded plastic case with glass front, adjustable joint to provide full 360 deg positioning of thermometer case and stem. Requires well for installation.


4

WEISS____________________________________ ____________________________________WEISSVAPOR ACTUATED DIAL THERMOMETERS

Order No. Model No. Temperature Range Dial Size Type Size Cap. Length

35VAT100 35BL3-5211-1 --20/100oF 3-1/2" Brass 1/2" 10 FT35VAT240 35BL3-5211-1 40/240oF 3-1/2" Brass 1/2" 10 FT35VAT300 35BL3-5211-1 100/350oF 3-1/2" Brass 1/2" 10 FTUse #231 well with above.

WELLOrder No. Description231 1/2" Brass Well

Connection

3-1/2" back flange case, bottom connection, union process connection, copper braid over copper cap tube.

WEISS vat SERIES therm 7/29/2008

GAUGE ACCESSORIES

Order No. Model No. Type Size MaterialLC14 51010 F X F 1/4" BrassMTC14 51005 M X F 1/4" BrassLC12 LC-12 F X F 1/2" Brass

Order No. Model No. Size Material PSIPSNBE 5000 1/4" Brass 1500 psi

PRESSURE SNUBBER

NEEDLE VALVEOrder No. Model No. Size Material PSI

25NVBR-4 51040 1/4" Brass 600

SYPHONSOrder No. Model No. Size Material PSI

SYPHN-4BA 371A 1/4" Angle Iron 500 @ 400oFSYPHN-4BRS 372A 1/4" Straight Brass 250 @ 400oFSYPHN-4BS 373E 1/4" Straight Iron 500 @ 400oF

COCKSConnection

Some form of pressure snubber should always be used in conjunction with any gauge subjected to rapidly fluctuating pressures and/or sudden shock. The dampening element is a 3/8" diameter X 1/8" thick disc of corrosion resistant, porous metal through which the pressure fluid is filtered. Discs of different pororsity are available for use with different fluids.

WEISS gauge ACCESSORIES 7/29/2008

_______________________________WELL TECHSTEM WELLSVarious wells for Bi-Metal dial thermometers or temperature controllers using 1/4" stem with 1/2" MPT threads.

Order No. Model No. Connection Stem MaterialBRSW-8X025-6 140051A 1/2" 2-1/2" BrassBRSW-8X025 100031A 1/2" 2-1/2" BrassBRSW-12X025 100032A 3/4" 2-1/2" BrassBRSW-8X040 105051A 1/2" 4" BrassBRSW-12X040 105052A 3/4" 4" BrassBRSW-8X060 110091A 1/2" 6" BrassBRSW-12X060 110092A 3/4" 6" BrassBRSWL-12X060 115052A 3/4" 6" BrassSSW-12X040 105052C 3/4" 4" Stainless SteelSSW-8X060 110091C 1/2" 6" Stainless SteelSSW-12X060 110092C 3/4" 6" Stainless Steel

well tech wells 7/29/2008


4

DELTA TRAK_______________________________

THERMOMETERSDigital pocket thermometer.

Order No. Description

PDT POCKET DIGITAL THERM 40/300oF

DELTA TRAK THERMOMETERS

POCKET THERMOMETERS____________________SPECIALTY THERMOMETERS

Order No. Model No. DescpriptionPTT010125 MA-PT125 1" DIAL POCKET TEST 25-125ºFPTT010160 MA-PT160 1" DIAL POCKET TEST --40/160oFPTT010220 MA-PT220 1" DIAL POCKET TEST --0/220oF

THERMOMETER, SPECIALTY 7/29/2008

a11 low temperature cutout control a19 high range ... · valve bodies: commercial--3/8",...

Documents