a104.extron dvs605setup

7/28/2019 A104.Extron DVS605setup

1/4

Mounting and Cabling

Step 1 Mounting

Turn o or disconnect all equipment power sources and rack mount the DVS 605 unit

using the pre-installed brackets (see image at right).

Step 2 Connect inputs

Connect inputs rom video sources to the applicable connectors marked Inputs.

See b through c above or video connector types andd or audio connectivity.

Step 3 Connect outputs

Connect video and audio output devices to the applicable connectors marked Outputs

(seee through k above).Step 4 Connect control devices

LAN portm Connect an LAN or WAN via this RJ-45 connector or remote control o the DVS 605 using an Internet browser orthe Extron conguration program, installed on a connected PC.

One connection LED lights green when connected to the LAN and one fickers amber as the devices communicate.

NOTE: Do not use standard telephone cables or LAN connection, as they do not support Ethernet or Fast Ethernet.Do not stretch or bend cables as transmission errors could occur.

Power and video input connections Output, user interface, and control connections

a AC power connector

b Universal analog VGA connectors inputs 1 and 2

c HDMI connectors inputs 3-5(Note: PIP is not available on input 5.)

d Audio 5-pole captive screw connectors inputs 1- 5 (audio models only)

e HDMI connector

fRGB/R-Y,Y, B-Y component VGAconnector

g 3G/HD-SDI connector (optional)(SDI models only)

h Genlock connectors input and loopthrough (SDI models only)

i Audio output (xed), 5-pole captivescrew connector (audio models only)

jRCA audio (S/PDIF) output connector(audio models only)

k Audio output (variable), 5-pole captivescrew connector (audio models only)

l Reset button and LED

m RJ-45 LAN connector

n RS-232 and IR 5-pole captive screwconnector

o Contact closure 5-pole captive screwconnector (shares a ground with RS-232)

DVS 605 Setup GuideThe Extron DVS 605 Digital Video Scalers are scaling products that allow most common signal ormats to be processed, scaled, andoutput in any desired ormat. This setup guide allows an experienced user to easily and quickly set up and congure aDVS 605 using step by step instructions. It covers how to perorm basic operations using the ront panel controls and selectedSimple Instruction Set (SIS) commands.

NOTE: For ull installation, conguration, menus, connector wiring, and operation details, see theDVS 605 User Guide,available at www.extron.com

Rack Mount

Bracket

Installation

L

1

R L

2

R L

3

R L

4

R L

5

R LFIXED

R LVARIABLE

R

100-240 VAC ~ .7A MAX

50/60HzRGB/R-Y, Y, B-Y

1

5

2

3

4

UNIVERSAL

AUX

HDMI

HDMI

GENLOCK3G/HD - SDI

RS-232 IR

Tx Rx SGG

CONTACT1 2 3 4 5

S/PDIF

FIXED

LAN

RESET

INPUT OUTPUTS REMOTE

AUDIO INPUTS AUDIO OUTPUTS

DVS 605 AD

1251

15

13 1462 94 10 11

873

RS-232/IR port For serial RS-232 control, connect a host computer or control system to the 5-pole captive screw connectorn.RS-232 protocol (deault values): 9600 baud, 1 stop bit, no parity, 8 data bits, no fow control. By deault the IR port is disabled.

Contact closure port For remote input selection o any o the ve inputs, connect a suitable contact closure control device tothe 5-pole captive screw connectoro. The contact closure port and the RS-232 port share a common ground.

Rear Panel Features

The DVS 605 AD is shown here. All other DVS 605 models have some but not all o the eatures shown below.


2/4

DVS 605 Setup Guide (Continued)

2

Setting the Front Panel Locks (Executive Modes)The DVS 605 has three modes o ront panel security lock that limit the operation o the unit rom the ront panel.

Executive mode 0 (disabled) The ront panel is ully unlocked. This is the deault setting.

Executive mode 1 (enabled) The ront panel is completely locked. It can only be enabled

and disabled using SIS commands, or through the embedded

web pages.

See the online DVS 605 User Guide or SIS commands.

Executive mode 2 (enabled) The ront panel is locked except or input switching, PIP, swap, and Auto-Image.

Step 5 Connect power

AC power connector Plug in a standard IEC power cord rom a 100 - 240 VAC, 50 - 60 Hz power source into this receptaclea.

Powering UpWhen powering up the DVS 605 unit, it undergoes a sel testing sequence (see image below). The LCD displays the deault displaycycle, with the signal type, resolution, and reresh rate or the currently selected input and the output resolution and reresh rate.

NOTE: When powered and not in any menu, the LCD screen deaults to cycling through the current input/output status. The

displayed content may vary depending on the input video signal type (see typical deault display below).

13sec.

Apply

Power

EXTRONDVS 605 XX

11sec.

Last active input

button(s) remains lit.

16sec. 60-1059-xx

FW v1.xx

All input LEDs flash

(red then green).

1 2 3

4 5 PIP

EXTRONELECTRONICS

1

2 sec.

2sec.

Default Display Cycle

IN RGBHV#1 640x480

IN 31.47 kHz#1 59.94 Hz

OUTPUT720p@60

2 sec.

2sec.

Display screen

first lights blank

Note: Times shown are approximate.

Front Panel OverviewThe DVS 605 is shown here. All other models have the same eatures shown below.

DVS 605

DIGITAL VIDEO SCALER

CONFIG

1 2 3

4 5 PIP

AUTO

SWAP

MENU

NEXT

ADJUST

1 762 4 5

3

EXTRON

DVS 605

aFront panel mini USB confguration port Connect a control system or computer to this mini USB port (cable not supplied)or device conguration, control, and upgrading the rmware.

bInput selection buttons and LEDs (1-5) Selects/switches inputs; adjacent LEDs indicate which input is active (current inputlights green, PIP input lights red).

cAuto-Image button Allows automatic image size and centering adjustments on selected input.

dPIP and Swap Image buttons These two buttons are: PIPOpens or closes the PIP (Picture-In-Picture) window SwapSwapsthemaindisplayedimageandthecurrentPIPinputwitheachother,orwhennotinPIPmode,itwil

switch between current and previous input.

eLCD display This 12x2 screen displays device settings and menu conguration inormation.

fMenu navigation buttons (Menu, Next) These buttons allow navigation through the menu system o the DVS 605.

gAdjust knobs These are used with the menu navigation buttons to adjust the device settings and picture control.

MENU

NEXT

Press and

hold for about

2 seconds.

EXEC. MODE 2ENABLED

EXEC. MODEDISABLED

or

LCD screen displays

either

Enabling or disabling Executive mode 2 from the front panel

I the DVS 605 unit is in Executive mode 0 (unlocked), the procedure shown at right selects

mode 2 (locked). I it is in Executive mode 2, this procedure selects mode 0 (unlocked).

When Executive mode 2 is enabled and a ront panel action is attempted (other than input

switching, PIP enable or disable, swap, and Auto-Image), the LCD displays the lock status or 2 seconds.


3/4 3

Conguring the DVS 605DVS 605 devices can be congured by any o the ollowing: via the ront panel, the Extron Congurator sotware, via the internal

web pages, or via RS-232/Ethernet or USB connection, using the Extron Simple Instruction Set (SIS) o commands (see rear page).

Front Panel Menu System

The scaler has seven ront panel conguration menus:UserPresetsPictureControlInputConfgurationOutputConfgurationAudioConfgurationAdvancedConfguration ViewCommSettingsExitMenu.Ahiddenmenu(EditCommSettings)isalsoaccessible.

NOTE: To access the hidden Edit Comm Settings menu, press and hold the input 5 and the Next button simultaneously. Releasethe buttons when the menu appears. Edit the setting as needed, then press Menu to exit and save the settings.

To use any menu, press the Menu button to access the main menu, then repeatedly press the Menu button to cycle through to thedesired menu. Press the Next button to enter and cycle through the desired submenu.

NOTE: Press Menu at any time to exit a submenu and return to the main menu.For detailed inormation on the menus, see theDVS 605 User Guide, available online at www.extron.com.

Menu

MenuMenu Menu

Menu Menu

USER

PRESETS

INPUT

CONFIGPICTURE

CONTROL

OUTPUT

CONFIG

AUDIO

CONFIGADVANCED

CONFIG

VIEW COMM

SETTINGSEXIT MENU?

PRESS NEXT

Menu

Menu

Menu

MenuNextNext

sec.

2sec.

Default Display Cycle

IN RGBHV#1 640x480

IN 31.47 kHz#1 59.94 Hz

TP T720p 6

2 sec.

To congure the DVS 605 using the front panel, follow the steps below:

1. Within the Output Conguration menu, use the Adjust knobs to select the output resolution and reresh rate, the outputsignal type, and the sync polarity to match the requirements o the display device. The HDMI ormat can be set to matchthe connected HDMI display.

2. From the Advanced Conguration menu, Test Pattern submenu, select the Alternating Pixels (Alt. Pixels) test pattern.Adjust the connected analog display's active pixels (size), total pixels (clocking), and pixel phase (ne sync) settings oroptimal picture quality.

3. From the Advanced Conguration menu, change the test pattern to Crop, and adjust the display's position settings untilall our sides o the crop pattern are visible. Disable the test pattern. No urther adjustments or Auto Images should beperormed on the display device itsel.

4. Use the Advanced Conguration menu to set the Aspect Ratio (Fill or Follow) or each input. Rotate either Adjust knob tothe desired setting.

5. Perorm Auto-Image on each DVS 605 input. Auto-Image is a quick way to size an input to t the current window size.To perorm Auto-Image on the current input, press the Auto-Image button, then press it again to conrm.

NOTE: Alternatively using the Input Conguration menu, make any desired advanced adjustments, including turning on oro Film detection, Horizontal and Vertical Start, Active Lines, Pixel Phase, and EDID setting selection.

6. Adjust the Overscan mode under the Advanced Conguration menu as required. Overscan masks Closed Caption andancillary data common on broadcast signals. (Applies to SMPTE input resolutions only.)

7. Use the Picture Control buttons to adjust the Horizontal and Vertical Position and Size, Brightness and Contrast, Color andTint, and Detail settings i needed.

8. Use the User Presets menu to save the adjustments to each input or manual recall later.

Extron Congurator SoftwareTo congure the unit using the Extron Congurator sotware, the sotware must be installed (rom the included DVD or romwww.extron.com) on a PC connected to the DVS 605 via an RS-232 or a LAN connection, or via the ront panel USB cong port.Installation creates a C:\Program Files\Extron\DVS 605 older and installs the program, a help le, and an uninstall utility.Ater installation, start the program and either connect via the comm (RS-232) port, TCP/IP, or by USB. For ull instructions press or click on Help>Contents.

Web pages

The DVS 605 can be congured, controlled, and operated through the Ethernet port when connected to a LAN or WAN, using aweb browser such as Microsot Internet Explorer. The browser displays the actory-installed web pages, which provide a means oviewing and operating the device. Access the HTML pages by entering the IP address o the unit in the browserAddress eld.

NOTE: I the system administrator has not changed it, DHCP is On (actory deault setting).I the unit is password-protected, enter the administrator or user password in thePassword eld.

A user name entry is required. Enteradmin or administrator level oruser or user level (all lower case letters).
http://www.extron.com/http://www.extron.com/


4/4

Upgrading the Firmware Using the Web Pages

The onboard rmware version o the DVS 605 unit can be upgraded via the actory-installed web pages when connected via theEthernet port to a LAN or WAN, using a web browser such as Microsot Internet Explorer.

Firmware upgrade les (with an EFF or ESS extension) or the DVS 605 unit are available atwww.extron.com. At the website,browse to the le location and download the latest rmware version to a PC connected to the DVS 605.

Access the DVS 605 internal web pages by entering the IP address o the unit in the browserAddress eld.

When the web pages open do the ollowing:

1. Click the Hardware button above the global navigation bar.

2. Click the Firmware Loader icon on the global navigation bar. The Firmware Loader screen opens.

3. Click Browse. The Choose File to Upload dialog box opens.

4. Browse to and select the downloaded rmware le to upload to the device. Valid rmware les have an EFF or ESS extension.

5. Click Open. This closes the dialog box and returns you to the Firmware Loader screen.

6. Click Upload. Uploading progress is displayed and will indicate when completed.

7. When the upload is complete the unit reboots. Any IP connections to the unit will need to be re-established.

4

DVS 605 Setup Guide (Continued)

Basic SIS Commands TableThe DVS 605 can be congured with specic SIS commands via RS-232 or a LAN connection. This table lists a selection o the

commands. For a ull list o SIS commands and variables see theDVS 605 User Guide, online at www.extron.com.

Command ASCII command(host to scaler)

Response(scaler to host)

Additional description

Select video and audio input X!! InX!All] Selects video and audio rom input X!.

Select video input X!& InX!RGB] Selects video only rom input X!.

Select audio input X!$ InX!Aud] Selects audio only rom input X!.

Execute Auto-Image 0*A Img0] Executes Auto-Image or current input.

Mute video to black 1B Vmt1] Mutes video and display a black screen.

Mute video and output sync 2B Vmt2] Mutes video and sync output.

Unmute video 0B Vmt0] Unmutes video.

PIP on EX!PIP} PipX!] Turns on PIP and displays input X!.

PIP o E0PIP} Pip0] Turns o PIP.

Swap % Tke] Swaps inputs between main and PIP windows, or currentand previous input when not in PIP mode.

Recall PIP preset (without input) 3*X2@. 3RprX2@] Recalls PIP preset X2@ without input.

Recall PIP preset (with input) 4*X2@. 4RprX2@] Recalls PIP preset X2@ with input.

Save PIP preset 4*X2@, 4SprX2@] Saves PIP preset X2@.

Enable Executive mode 1 1X Exe1] Locks out entire ront panel.

Enable mode 2 2X Exe2] Allows limited ront panel adjustments only.

Disable Executive mode 0X Exe0] Allows all ront panel adjustments and selections.

View ront panel lock status X 0](or 1])(or 2])

Shows executive mode status.

NOTE: Changes made to all Ethernet settings do not take eect until the reboot networking command (2BOOT) is issued.

Set DHCP to O or On EX1&DH} IdhX1&] Sets DHCP mode.

View DHCP status EDH} X1&] Shows DHCP setting.

Set IP address EX1(CI} X1(] Sets IP address to X1(.

View IP address ECI} X1(] Shows current IP address X1(.

Reboot network E2BOOT} Boot2] Restarts network ater IP address or DHCP changes.

NOTE: X! = Input number (1 5) X1& = DHCP mode (0 = O, 1 = On, deault) X1( = IP address (such as 192.168.254.254)X2@ = PIP presets (1-16)

68-2110-5

Rev. 04 1

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron Asia

+65.6383.4400

Extron China

+86.21.3760.1568)

Extron Korea

+82.2.3444.1571

Extron Europe

+31.33.453.4040

Extron Japan

+81.3.3511.7655

Extron Middle East

+971.4.2991800

Extron India

+91.80.3055.3777

2012 Extron Electronics All rights reserved. All trademarks mentioned are the property o their respective owners. www.extron.com
http://c/Documents%20and%20Settings/cpeace/Local%20Settings/Application%20Data/Adobe/InDesign/Version%207.0/en_US/Caches/InDesign%20ClipboardScrap1.pdfhttp://c/Documents%20and%20Settings/cpeace/Local%20Settings/Application%20Data/Adobe/InDesign/Version%207.0/en_US/Caches/InDesign%20ClipboardScrap1.pdfhttp://c/Documents%20and%20Settings/cpeace/Local%20Settings/Application%20Data/Adobe/InDesign/Version%207.0/en_US/Caches/InDesign%20ClipboardScrap1.pdfhttp://c/Documents%20and%20Settings/cpeace/Local%20Settings/Application%20Data/Adobe/InDesign/Version%207.0/en_US/Caches/InDesign%20ClipboardScrap1.pdf