86902551 infrared headphones project report

3
Infrared headphones project report/pdf/ppt download Abstract : Using this low-cost project one can reproduce audio from TV without disturbing others. It does not use any wire connection between TV and headphones. In place of a pair of wires, it uses invisible infrared light to transmit audio signals from TV to headphones. Without using any lens, a range of up to 6 metres is possible. Range can be extended by using lenses and reflectors with IR sensors comprising transmitters and receivers. IR transmitter uses two-stage transistor amplifier to drive two series-connected IR LEDs. An audio output transfonner is used (in reverse) to couple audio output from TV to the IR transmitter. Transistors Tl and T2 amplify the audio signals received from TV through the audio transformer. Low-impedance output windings (lower gauge or thicker wires) are used for connection to TV side while high-impedance windings are connected to IR transmitter. This IR transmitter can be powered from a 9-volt mains adapter or battery. Red LED1 in transmitter circuit functions as a zener diode (0.65V) as well as supply-on indicator. IR receiver uses 3-stage transistor amplifier. The first two transistors (T4 and T5) form audio signal amplifier while the third transistor T6 is used to drive a headphone. Read more: Infrared headphones project report/pdf/ppt download - | FaaDoOEngineers.com http://www.faadooengineers.com/threads/5182-Infrared-headphones-project-report-pdf-ppt- download#ixzz1qKIu6NpW

Upload: arjun-sreenivas

Post on 02-Jan-2016

10 views

Category:

Documents


0 download

DESCRIPTION

Abstract : Using this low-cost project one can reproduce audio from TV without disturbing others. It does not use any wire connection between TV and headphones.

TRANSCRIPT

Page 1: 86902551 Infrared Headphones Project Report

Infrared headphones project report/pdf/ppt download

Abstract : Using this low-cost project one can reproduce audio from TV without disturbing

others. It does not use any wire connection between TV and headphones.

In place of a pair of wires, it uses invisible infrared light to transmit audio signals from TV to

headphones.

Without using any lens, a range of up to 6 metres is possible. Range can be extended by using

lenses and reflectors with IR sensors comprising transmitters and receivers.

IR transmitter uses two-stage transistor amplifier to drive two series-connected IR LEDs.

An audio output transfonner is used (in reverse) to couple audio output from TV to the IR

transmitter.

Transistors Tl and T2 amplify the audio signals received from TV through the audio

transformer.

Low-impedance output windings (lower gauge or thicker wires) are used for connection to

TV side while high-impedance windings are connected to IR transmitter.

This IR transmitter can be powered from a 9-volt mains adapter or battery. Red LED1 in

transmitter circuit functions as a zener diode (0.65V) as well as supply-on indicator.

IR receiver uses 3-stage transistor amplifier. The first two transistors (T4 and T5) form audio

signal amplifier while the third transistor T6 is used to drive a headphone.

Read more: Infrared headphones project report/pdf/ppt download - | FaaDoOEngineers.com

http://www.faadooengineers.com/threads/5182-Infrared-headphones-project-report-pdf-ppt-

download#ixzz1qKIu6NpW

Page 2: 86902551 Infrared Headphones Project Report

Using this wireless IR Headphones circuit electronic project you can transmit audio signal

using an infrared connection .This wireless IR Headphones circuit diagram electronic project

is composed by two parts : transmitter and receiver . This is not an RF transmitter , so you

will need to design both parts of application .

Using this infrared audio signal transmitter you can build an infrared cordless headphone ,

that can be very useful if is used with an TV or some other electronics device that can disturb

other persons .

Without using some special devices this electronic project can be used over an 6 meters range

.The transmitter circuit use an output transformer ( in reverse ) to couple the TV to the IR

transmitter . T1 and T2 transformers are used to amplify the audio signal from the audio

transformer .

The IR receiver module use a three stage transistor amplifier .The VR2 potentiometer is used

to adjust the clarity . To have an high efficiency and a maximum range for this IR circuit

direct photo-transistor towards IR LEDs of transmitter .

Both of these circuits needs to be powered by a 9 volts DC power supply .

Page 3: 86902551 Infrared Headphones Project Report