8/02 abpa 81/2x112 august meeting details meetings of the san antonio chapter abpa are usually held...
TRANSCRIPT
TheDirectConnection
A newsletter dedicated to Cross Connection Control and Backflow PreventionAugust 2002 Vol. 12 Issue 8
NoticeTo: All Backflow Assembly TestersDate: August 1, 2002Subject: Field modifications to Backflow Prevention Assemblies
Gentlemen,This letter is in regards to SAWS position on field modifications to backflow prevention assemblies.Specifically, we are concerned with field changes of an assembly from a double check detector backflowprevention assembly (DCDA) to a double check valve assembly (D/C). This question has been raised beforeby field personnel who wanted to change the “gender” of an assembly after receiving it from the supplier/manufacturer. SAWS follows the University of Southern California Foundation for Cross ConnectionControl and Hydraulic Research specifications which states that an Approved backflow preventionassembly “… shall be delivered for installation completely assembled by the original manufacturer…”This has been required for many years to insure that the assembly is installed in its proper configuration.Any modifications to the assembly by field personnel will invalidate the assembly and cause disapproval bySAWS.
The DC and DCDA configurations may be similar, but for most manufacturers the springs contained in theDCDA mainline check valve(s) are different (i.e., greater spring load) than the DC. If the proper DCDAsprings are not utilized, the bypass may not function properly (i.e., detect unauthorized flow of waterthrough the bypass). Even if performed by representatives of the manufacturer, the assembly would not beconsidered approved by SAWS. Field modifications do not have the same quality control procedures as atthe manufacturers’ manufacturing plant. So in keeping with USC recommendations and SAWSrequirements changing the “gender” of an approved backflow prevention assembly will be disallowed.
Respectfully,
Bruce RathburnSupervisor-Backflow PreventionSan Antonio Water System
Membership Duesshould be paid
before the end ofJanuary or a late fee
will be assessed
Safety TipOne thing you see going down the road every day is construction going on with theuse of water hauling equipment. The water purveyor has a keen interest on howthis equipment is filled. If you see a tank being filled and no air gap or backflowpreventer protecting the water source. Be a concerned citizen and check it out. Youcould be saving yourself or some unsuspecting worker from drinking contami-nated water!!!
2
August Meeting DetailsAugust Meeting DetailsAugust Meeting DetailsAugust Meeting DetailsAugust Meeting Details
Meetings of the San Antonio Chapter ABPA areusually held the second Thursday of every month. -Dinner and refreshments are served at 6:15 p.m. sharp,with the meeting at 7:00 p.m. the entry gates to thepump station will be closed and locked promptly at6:30 p.m. due to security reasons. The next meeting is:
Date: Thursday, March 14, 2002Time: 6:15 p.m. - 10:00 p.m.Location: 615 E. Theo
Mission Pump StationProgram: SAWS Mission Pump StationMeal: U.S. Filter / Watts-Ames
No alcoholic beverages allowed by SAWS policy
Backflow TriviaWhat is the best method of backflow
prevention protection?Answer on page 4
Backflow HappensRon Renouf, President, [email protected]
Have you mailed your application with the$105 fee for conversion of your BPAT accreditation toa license? I would like to use this space to make onelast effort to stress the importance of doing this byAugust 30,2002. It is your personal license and youneed to be sure that the paperwork is submitted ontime. Remember, you will be the one who has to takethe forty hour course again if somehow things havefallen through the cracks. This can be expensive andthere are no plans for ABPA-SA to provide the fortyhour course training for members who fail to apply ina timely manner. If you have any questions you maycall the TNRCC Operator Certification Section at(512)239-6133.
Help WantedTalented model builders needed to
participate in the designing and buildingof a working backflow display.
Big ThanksTO: Bacflo Unlimited (Troy) and Santos
Trousdale(David) for a great presentation!!!
Please Make Time To Attend:
The Texas Home and Garden ShowConvention Center August 24,25
ABPA-SA Booth #TBA
The South Texas Industrial & Construction ShowFreeman Coliseum
September 17 and 18 noon ‘til 7 and noon till 5ABPA-SA Booth # 214
Looking for volunteers to work the boothsContact Ron Renouf at 696-1411
You Are Your Own Safety Supervisor
In today s environment, no businessorganization of any size attempts to operate without asafety department. The person in charge of thisdepartment may be called the safety director, safetymanager, or the safety administrator. Whatever thetitle: that person is responsible for conducting thecompany s safety program. However the safety personcan not get into the batter s box, let alone to first base,without the help and cooperation of the employees onthe job - You.
When you were hired, you were giveninstructions covering every detail of the work youwere expected to perform. You may have beenassigned to other types of work now and then, buteach time your job was changed the same procedurewas followed. Before doing the job on your own, youreceived enough training to assure your supervisoryou could handle the work safely and efficiently. Thenand only then did the supervisor allow you to go aheadwith your job duties!
There are many ways to bring home theimportance of safety. Two ways are distributingpublications and holding regular meetings or safetytalks. These talks emphasize safe practices for specificoperations. No matter what methods are used to getthe word out about safety, the basic purpose is thesame: To Prevent Accidents.
Cont’d on Page 4
3
303 NORTH PARK DRIVE (78216-2726)P.O. BOX 460169 • SAN ANTONIO, TEXAS 78246-0169
Stocking Distributors of Industrial, Commercial,and Residential Plumbing Supplies
Phone: (210) 344-3013 • FAX: (210) 344-8120
FERGUSONENTERPRISES, INC.
Contact:Febco PO Box 8070, Fresno, CA 93747PH. (209) 252-0791 FAX (209) 453-9030
BackflowPreventionAssemblies
®
Model 825YReduced Pressure Assemblies• All sizes are USC approved.• Lowest independently documented head
loss in the industry.• Available from inventory now.
Advertise in TheDirectConnection
Business Card1/4 Page1/2 PageFull Page
$100$150$300$500
HOT BOX®ENCLOSURES
Insulated EnclosuresFor: Pipes, Valves and
EquipmentFAX (904) 783-6965
(800) 736-0238http://www.hot-box.com
See
Us In
SweetsourceCERTIFIED
ASSE
THE ORIGINAL
Post Office Box 16045, Houston, Texas 77222-604533 Lyerly, Suite B-5, Houston, Texas 77022Phone (713) 699-5778FAX (713) 699-0842
WWIP CORP.
11410 Grissom LaneDallas, Texas 75229
Phone (214) 243-3633FAX (214) 243-3632
ADSIZE
ONEYEAR
4
“The Direct Connection” is published monthly and may be obtained by becoming a member of theABPA-SA. Due to the expenses associated with printing and mailing, future editions will be mailedto members only. Opinions or facts within “The Direct Connection” are not necessarily representa-tive of the opinions of the American Backflow Prevention Association and may or may not representan official policy. Additionally, the opinions or facts of contributors or advertisers may or may notrepresent an official policy.
Published by the ABPA-Region IV,Editor: Bruce Rathburn,Assistant Editor: Robert Stricker.Layout, Publishing & Circulation:Alamo Iron Works-Fernando Galdeano
For further information about ABPA,contact:Bruce Rathburn1222 N. Main(210) 704-7136
®
ALAMO IRON WORKS
Call our valve specialistswith any questions!
Shop online at our award-winning Web site:www.AIWnet.com
Or call toll-free: 1-800-292-7817
Alamo Iron WorksAlamo Iron WorksStocks Backflow PreventersStocks Backflow Preventers
And Spare PartsAnd Spare Parts
If the company’s safety program is to succeed, you must take responsibility for’your own safety. If you don’t, youendanger not only your own life but also the lives of those with whom you work.
In the water utility industry, all individuals are expected to supervise their own work to a large extent. Safebehavior is right at the top of the items to watch. Although your supervisor is charged with seeing that your work iscompleted safely and satisfactorily, maximum safety results only from teamwork. Each of you must supervise your ownwork. After all, your supervisor cannot watch every move of every person on the team.
You can work hard and long to develop the best safety program possible and can provide a variety of interesting andinformative materials to carry out the program. However if you and your fellow employees fail to cooperate and refuse toact as your own safety supervisors, the safety program will fall apart at the seams. Accepting your personal responsibility isan essential cog in a gear that must always be in excellent running order.
The main areas of responsibility for the operation of a good safety program include top management’sresponsibility, supervisory responsibility, and your responsibility as the employee on the job. For aneffective safety program, each of these areas must be handled competently. If anyone fails to carry outhis or her duties or responsibilities for accident prevention, injuries can and will occur.
So in conclusion, never underestimate your responsibility for the success of a safetyprogram. No matter how much time and honest effort go into the organization of this program, if youdo not accept your responsibility, the program will never attain its goal of an accident-free operation.
BackflowTrivia Answer:
Air gap!
Safety Supervisor... Cont’d from Page 2
5
“BAC-FLO UNLIMITED”“BAC-FLO UNLIMITED”“BAC-FLO UNLIMITED”“BAC-FLO UNLIMITED”“BAC-FLO UNLIMITED”TRAINING BY EXPERIENCED INSTRUCTORS
“BAC-FLO UNLIMITED: DON’T SETTLE FOR LESS”
� BACKFLOW PREVENTION CONSULTING & TRAINING – INTRO. COURSES FOR CLERKS� 40 HOUR TESTER CERTIFICATION COURSES - TNRCC STATE AND NATIONAL CERT.� TESTER RE-CERTIFICATION COURSES (EXCLUSIVE: FREE PARTS MANUAL)� SITE TUBES – BLEED OFF VALVES – GAUGE TESTING� ADVANCED TROUBLESHOOTING & REPAIR COURSES� EXCLUSIVE: FREE GAUGE TEST INCLUDED WITH TESTING COURSES� FREE FUTURE TROUBLESHOOTING ASSISTANCE
TNRCC APPROVED TRAINING CREDITS — ASK ABOUT ABPA DISCOUNTS
NOTE: SAN ANTONIO TESTER COURSES ARE CONDUCTED BI-MONTHLY BOTH AT BFU'S NEWI-H 10 BOERNE LOCATION AND AT THE USUAL SOUTH SAN ANTONIO LOCATION
EXCLUSIVE: TWO INSTRUCTORS FOR EACH COURSE &SEPARATED PRACTICE STATIONS
LEAD INSTRUCTOR: Fred Baird – Over 30 Yrs. Backflow Related ExperienceContact: Bac-Flo Unlimited @ Ph/Fax 210-698-0411 www.bacflo.com
6
7
8
WATTS, THE BROADEST LINEIN BACKFLOW PREVENTION...
offers as standarda double check valveassembly that can bemounted in a meter boxwith test cocks& access coverspointing up for easeof maintenance.Fully approved.
◆ Top access - testing/maintenance
◆ One cover for all maintenance
◆ USC approved orientation
◆ Replaceable seats
◆ Captured springs
For Improved Performance,True Line Size Valves!
Watts true line size valves give you
exactly what you've wanted in backflow
preventer valves: better performance,
smaller size, lighter weight
and significantly in-
creased dependability.
Unlike typical "Y"
pattern valves, true line size valves provide an
BACKFLOW PREVENTION DIVISION
WATTSREGULATOR
Houston office 1-800-460-1940Dallas office 1-800-568-5686
even distribution of flow, reduce wear on internal
parts and allow more dirt and debris to pass
without causing failures. Available in
three of our most popular perfor-
mance models, 007, 008
and 009, true
line sizing will forever
change the way you
look at backflow
preventers.
9
Backflow Preventer &Water Meter Assembliesfor Fireline, Domestic, & Irrigation Water Service
City Approved:Austin
Dallas/FWSan Antonio
HoustonCorpus Christi
Brownsville& More...
Other Products:Grease/Lint Traps
Oil-Water InterceptorsAcid Neutralization Tanks
Wastewater TreatmentManholes/Catchbasins
Pump Lift StationsAboveGround Fuel Tanks
Water Storage/Break Tanks• Preassembled in Concrete Vault• Pre-Engineered & Pre-Tested• Certified Brand Name Components• Saves Time, Labor, & $$$$• Immediate Delivery & Setting Service Throughout Texas
800-256-8041
10
WILKINSWILKINS
SAN ANTONIO STOCKSTOCKING:1/4" thru 8"
DCs & RPs (NRS & OSY Gates)100s of devices...plus
THE NEW TOP ACCESS/TOP REPAIRWILKINS Double Check.
Why go to Dallas or Houston?USE A SAN ANTONIO SOURCE. Save
freight, time & money!
CMR, Inc. - mfrs. rep.4446 Centergate
San Antonio, Texas 78217(210) 654-8015fax: 654-1327
Model 950XL Top Access Double Check Valve Assembly
FINDING BACKFLOW REPAIR PARTS A PROBLEM??
BAVCOBACKFLOW APPARATUS
&VALVE CO.
Call the parts experts
BE GUARANTEEDNO PROBLEMS
(800) 458-3492
RIGHT PARTS
RIGHT INFO
RIGHT NOW
✓✓✓
11
Here’s the best wayto keep foreignsubstancesout of awater supply system.
U.S. made backflow preventers from Conbraco Industries make your job easier.
You get a complete selection for commercial, residential, and industrialapplications. Choose from sizes as small as 1/4 inch to as large as 8 inch. Selectcontinuous pressure, RPZ, dual check, double check, and vacuum breakerdevices.
Each Conbraco backflow prevention device is engineered and manufactured withprecision for worry-free performance.
You get tested, proven performers, conforming to AWWA, ASSE, LAPMO, andCSA specifications and designed to meet USC Research Foundation approval.
They're easy to install. Easy to maintain in line. Easy to field test in line.
Our extensive distributor network is ready to serve you anytime, anywhere. Calltoday for more technical information.
(704) 847-9191 FAX: (704) 847-4610
MANUFACTURERS REPRESENTATIVE
KNOX& ASSOCIATES
Houston (713) 462-7766GENE LAKE Wats 800-231-7191830-583-2448 Fax (713) 690-6228
707 Loma Vista Office/WarehouseKenedy, Texas 78119 10002 Grover
Houston, Texas 77041
Conbraco Industries, Inc.P.O. Box 247Matthews, NC 28106
ABPA - S.A. ChapterP.O. Box 47895San Antonio, TX 78265
ABPA-SA Chapter(210) 599-6525
Address Service Requested
M
AD E
I N U
SA