80158

SOFTWARE RELEASE FORMSOFTWARE RELEASE FORM

Project Domestic L-Band MDS Project Number 5376

Software Identity and Release No.

LES BAP and SOC Executables Release 80158

Release to Telecomunicaciones de Mexico Date 8/4/23

Reason for Release

This maintenance release of the Domestic L-Band MDS LES software is the latest version of the software baseline.

Release Definition See accompanying Release Notes for an overview of the functions supported and content of the release.

Release Media A TK85 tape containing the released BAP will be sent to site, labelled TELECOMUNICACIONES DE MEXICO BAP REL 80158 060921 A TK85 tape containing the released SOC will be sent to site, labelled SOCREL Telecomunicaciones de Mexico 80158 060921

Associated changes

Software Release Notes accompany this release. These notes must be read fully before installation of the software.

A list of documents accompanying this release is included in the Software Release Notes.

Approvals Name Date Comments

Prepared by M.J.Franklin 8/4/23

Approved by G.A.Bond

1

Hughes Network Systems EuropeSunrise Parkway, Linford Wood, MILTON KEYNES,MK14 6LS, U.K.

Software Acceptance

Name Date

Installed by

Accepted for Customer by

Build Record

Source Location See firesafe log/project release notes log

Compiler VAX Ada v2.2-38 , Linker 05-13

Build Instructions As per Inmarsat-C local procedure Integration Build Procedure (IBP) A4-SPM-002840-1

Programming Information (for firmware)

Target Hardware N/A

Programming Equipment N/A

File format N/A

Devices N/A

File names N/A N/A N/A N/A N/A

Devices location N/A N/A N/A N/A N/A

Part number N/A N/A N/A N/A N/A

Checksum N/A N/A N/A N/A N/A

Release Notes

Problems Fixed Maintenance Release bringing TdM up to the latest software baseline.

Testing Appendix B shows the results of Integration and System testing performed at HNS.

Outstanding faults No faults were found during testing of this release.

Operational Considerations There are no operational considerations associated with this release.

Documentation Changes Appendix E lists the documentation changes associated with this release.

Installation notes See Release Notes

Support Information Any missing items should be reported immediately to Customer Support at HNS Europe. Telephone +44 1908 425300. System problems should be reported to HNS Europe using the agreed CSPR procedure.

2

SOFTWARE RELEASE NOTESSOFTWARE RELEASE NOTES

- PROBLEMS FIXEDThis is a full release of the latest baseline of LES Software.

- TESTING Appendix B shows the results of Integration and System testing that has been performed at HNS.

- FAULTS FOUND No faults were found during testing of this release.

- OPERATIONAL CONSIDERATIONS There are no operational considerations associated with this release

- INSTALLATION GUIDE Appendix C describes the installation procedures for release 80158.

Appendix D contains details of the save-sets and any other files in this release.

- DOCUMENTATION CHANGESAppendix E lists the documentation changes associated with this release.

- SUPPORT INFORMATION Any missing items should be reported immediately to Customer Support at HNS Europe,

Telephone: +44 1908 425300. System problems should be reported to HNS Europe using the agreed CSPR procedure.

- SOFTWARE COPYRIGHT NOTICEAppendix F lists this notice.

Hughes Network Systems EuropeSunrise Parkway, Linford Wood, MILTON KEYNES,MK14 6LS, U.K.

PROJECT: Domestic L-Band MDS PROJECT NUMBER(S): 5376 SOFTWARE ITEM: LES BAP and SOC Executables RELEASE: 80158 CUSTOMER: Telecomunicaciones de Mexico DATE: 8/4/23

Table of Contents

Appendix A Enhancements and Problems fixed....................................................................................................................2

A.1 (C)SPRs Fixed in this Release...................................................................................................................................2

Appendix B Testing................................................................................................................................................................2

Appendix C Installation Guide for Release 80158.................................................................................................................3

C.1 Introduction................................................................................................................................................................3C.2 Actions Prior to Installation.......................................................................................................................................3C.3 Installation..................................................................................................................................................................3C.4 Fall-Back....................................................................................................................................................................6

Appendix D Save Set Details..................................................................................................................................................7

D.1 BAP tape contents......................................................................................................................................................7D.2 SOC tape contents......................................................................................................................................................7

Appendix E Documents included in 80158...........................................................................................................................8

Appendix F Software Copyright Notice.................................................................................................................................9

Appendix A Enhancements and Problems fixed

A.1 (C)SPRS FIXED IN THIS RELEASE

There are no Telecomunicaciones de Mexico CSPRs fixed in this release hence no test details are included.

Appendix B Testing

The released executables have been subjected to a regression test covering those aspects affected by this release. No problems have been found.

Appendix C Installation Guide for Release 80158

C.1 Introduction

The installation should be scheduled to take place at such time that the outage will result in minimum disruption to traffic, and when support will be available from HNS.

The saveset must be loaded, following instructions in the Customer Release Configuration Guide (A4-SCG-3076-1).In summary the installation steps to be performed, unless specifically excluded in the comments column, are:

For the new automated installation procedure to function smoothly it is important not to log into the first newly installed BAP until the correct stage ( see Installation Instructions below). Review Sections 11 through 14 at this point.

C.2 Actions Prior to Installation

In installations where the SOC Workstations do not have integral Tape devices either an external unit should be procured or the SOC Software Savesets can be installed via the BAPs. The latter is performed as follows:

Identify a BAP Disk with at least 80000 spare blocks. ( DSA1 on MXBPA is assumed in this example hereafter).The following commands will create the directory that the SOCs will require for installation from this BAP:MXBPA> SET DEF DSA1:[CES.REL8015]MXBPA> CREATE/DIRECTORY [] Insert the SOC Software tape into BAP Tape device ( MUA0 assumed ).These commands will transfer the raw Savsets onto BAP disk from the tape:MXBPA> MOUNT MUA0 8015MXBPA> COPY/LOG MUA0:*.SAV []*A proxy user account will be required by each of the SOCs (SOC01A in the next example). Check if they exist by:MXBPA> SET DEF SYS$MANAGERMXBPA> MC AUTHORIZEUAF> SHOW /PROXY [SOC Node]::SYSTEMIf proxy accounts do not exist then:UAF> ADD/PROXY [SOC Node]::SYSTEM SYSTEM /DEFAULT

Now the SOC Savesets are available on a BAP Disk. During the SOC Installation specify MXBPA::DSA1 as the location for all savesets.

C.3 INSTALLATION

XConfig.Guide Section

Action Comments

PREPARATION

1. Copy the SAD_PROTECT_FILES.DAT file to [BAPSW.REL801x.SAD.EXECUTE], where x represents the highest (current) release.

Only required if this file does not exist here already as a result of a previous release, or has been updated by HNS.

2. Insert tape

3. 4.1.2.2 Extract the PROJINSTALL.SAV save set. Re-insert tape ready for BAP installation

4. 2.2.1 Protect the following extra-ordinary files which are not covered by the automated process:

None required in this release

5. 2.3 Archive the Online Database.

6. 2.4 (7.2.1)

Dump the Online Database.

7.2.5

Generate the following POP files that may be needed in case of fallback:


INSTALL FIRST SOC

8. 4.2.1 Stop and deinstall one SOC. First determine if the logical SOC$REL_DISK is defined in terms of LES$DISK0, or a disk name

9. 4.2.3 Install the new software on the SOC.(Including 'Projinstall.Sav')

Not 4.2.3.1, 4.2.3.2Use the SOC$REL_DISK translation when prompted for the installation disk

INSTALL FIRST BAP (NON REDUNDANT)

10.7

4.1.1 Stop and deinstall the Standby BAP. No standby now

11. 4.1.2 Install the new software on the stopped BAP (this includes the first pass FEP install).With the tape already inserted, the installation procedure should offer correct default locations and file names.

Not 4.1.2.1All defaults should be accepted, unless stated below or are known to be wrong, in which case, supply the correct informationDo NOT manually delete the [BAPSW.REL…] files

Reply 'N' to the change FEP load file question. Enter N when asked if each FEP should be triggered

When asked if the INSTALLFEP.COM file should be run, ONLY accept the default (N) if the 'old' BAP is to remain Master for any appreciable time following this installation and re-starting this BAP, otherwise IGNORE this default and enter Y

This completes the installation and the BAP may be re-booted as prompted

DO NOT log in to BAPSYS until required.

Before logging in, ensure that both Email PCs (where applicable) have BAPA and BAPB definitions pointing to the BAP NOT affected. Remember to restore once installation completed.When starting the BAP for the first time, observe all start-up messages – check for errors which may scroll off.


Action Comments

OUTAGE

12.14

4.1.4 Start of installation outage - stop current master

13.15

7.2.2 Optionally perform DBCC on the Online Database.

Customer must trade off longer outage (+~30 mins.) against added security).

14.9

4.1.5 Log on via BAPSYS on upgraded BAP and carry out 'Additional post installation actions'

(Automated sequence)

Do not recreate SOI files when asked The original protected SOI files containing the workstation set up will be restored next.

No 'protected' files have been updated in this release, so choose the options to replace the protected files - overwriting the released files

(See 4.1.5.2). However, if local changes have been made to SAD_PROTECT_FILES.COM, then this should be replaced.

This should be detected as a 'first pass'. The node name of the other BAP will be displayed and its installation disk found.The option to rename the FEP load files on that disk will be offered. Assuming that there is no reason for delay, proceed and rename those filesReply 'Y' to the request to trigger FEPs (see 4.1.4.1/4.1.4.3 for description)

IF and ONLY if the option to run the INSTALLFEP.COM file was not exercised (i.e. there has been a delay) then answer N. Immediately after this installation utility has completed, the this installation file should be run, followed by the re-trigger COM file displayed at this time.

An online database update is now required, reply to the questions as indicated in the comments:

If the online database has not yet been started on this node, then this will be done now

Perform online database conversion for: Options 39 to 46

Is installation complete AND no database upgrade required Y/N [Y] NIs installation complete AND a database upgrade IS required Y/N [Y] Do you need to upgrade the ONLINE database now Y/N [Y]

Once ONDB has started, reply again to the questionDo you need to upgrade the ONLINE database now Y/N [Y]

This is likely to take approximately 30-60 seconds per step - see 7.2.3.

If no other actions outstanding, then:

15.17

8 Start newly upgraded BAP and SOC. End of outageBefore logging in, ensure that both Email PCs (where applicable) have BAPA and BAPB definitions pointing to the BAP NOT affected. Remember to restore once installation completed.When starting the BAP for the first time, observe all start-up messages – check for errors which may scroll off.

CHECK SYSTEM

16.18

4.1.5(10)

Ensure system functions correctly (do not move on until agreed that there will be no fall back).

Tests required by Appendix B of these release notes are the OSAT tests

PREPARE AND INSTALL SECOND BAP

17. - In addition protect the following files for this installation:


18. 4.1.1 Deinstall the second BAP (already stopped).

19. 4.1.2 Install the second BAP (this includes the second pass FEP install).

Not 4.1.2.1

No 'protected' files have been updated in this release, so choose the options to replace the protected files - overwriting the released files

(See 4.1.5.2). However, if local changes have been made to SAD_PROTECT_FILES.COM, then this should be replaced.

Reply 'Y' to the change FEP load file question as new question requests the entry of the VAX type, enter the appropriate number as prompted.

FEP load files will need updating for this installation. The FEP load file type will be required Enter N when asked if each FEP should be triggered

When asked if the INSTALLFEP.COM file should be run, enter Y

20. 4.1.3 Perform post installation checks.

21. 8 Start second BAP. Redundant BAPsFEPs will not be re-triggered

Do not recreate the SOI files when asked. No changes are required.


Action Comments

INSTALL OTHER SOC(S)

22. 4.2.1 Stop and deinstall 'other' SOC(s). First determine if the logical SOC$REL_DISK is defined in terms of LES$DISK0, or a disk name

23. 4.2.3 Install the 'other' SOC(s).(Including 'Projinstall.Sav')

Not 4.2.3.1, 4.2.3.2Use the SOC$REL_DISK translation when prompted for the installation disk

24. 8 Start the 'other' SOC(s)

TIDY AND BACKUP

25. 2.1 Tidy up & backup disks

26. 2.3 Archive the Online Database.

27. 2.4 (7.2.1)

Dump the Online Database.

C.4 Fall-Back

See Configuration Guide, Section 10The actions listed there are only to be performed if it is required to restore the system to the previous release.

Appendix D Save Set Details

This release comprises the full set of LES software contained within the supplied saveset(s) . The contents will not be listed here. The approximate total size of this release is 825000 for the BAP, and 69000 blocks for the SOC.

D.1 BAP TAPE CONTENTS.

PROJINSTALL.SAV

Save set: BAPSW.SAVWritten by: INTEGRATION UIC: [000020,000244]Date: 21-SEP-2006 15:19:56.11Command: BACKUP/LOG/IGNORE=LABEL/LABEL=8015/COMMENT=MEXICO/NOASSIST/VERIFY [000000]BASELINE.DAT;,[ADV.*]*.*;,[APM.*]*.*;,[BM.*]*.*;,[CD.*]*.*;,[CRM.*]CRM_MEMORY_PARAMETERS*.DAT;,[CUTL.*]*.*;,[DAC.*]*.*;,[DBCONV80000.*]*.*;,[DCD.*]*.*;,[DEB.*]*.*;,[DIM.*]*.*;,[DRH.*]*.*;,[EM.*]*.*;,[ERR.*]*.*;,[FCR.*]*.*;,[FDCD.*]*.*;,[FELNSYS.*]*.*;,[INT.*]*.*;,[KRMT.*]*.*;,[LFM.*]*.*;,[MAR.*]*.*;,[MC.*]*.*;,[MCM.*]*.*;,[MDIR.*]*.*;,[MSCH.*]*.*;,[OFDB.*]*.*;,[PINS.*]*.*;,[PIPM.*]*.*;,[PRC.*]*.*;,[RG.*]*.*;,[RP.*]*.*;,[SAD.*]*.*;,[SDA.*]*.*;,[SDC.*]*.*;,[SM.*]*.*;,[SOCV.*]*.*;,[SOI.*]*.*;,[TOKM.*]*.*;,[UTL.*]*.*;,[X4BM.*]*.*;,[XCCC.*]*.*;,[XCDC.*]*.*;,[XCIC.*]*.*;,[XCTI.*]*.*;,[XCVP.*]*.*;,[PINS_MEXICO.*]*.*;,[FAX.*]*.*;/EXCLUDE=(*AMSC*.*,*ITALY*.*,*OTC*.*,*GREE*.*,*THAI*.*,*_FT_*.*,*_FT.*,*_INT.*,FDCD_EXT_MGR_DATA.DAT,SAD_PROCESS_DATA.DAT,XCCC_GEN*.*,XCCC_*CALL*.*,XCCC_LOAD*.*,XCCC_CREA*H.*) MKA0:BAPSW.SAVOperating system: OpenVMS VAX version V5.5BACKUP version: V5.5-2CPU ID register: 0B000006Node name: EARTH::Written on: _EARTH$MKA0:Block size: 8192

D.2 SOC TAPE CONTENTS.

PROJINSTALL.SAV

Save set: SOCSW.SAVWritten by: INTEGRATION UIC: [000020,000244]Date: 21-SEP-2006 16:48:55.72Command: BACKUP/LOG/IGNORE=LABEL/LABEL=8015/COMMENT=MEXICO/NOASSIST/VERIFY [CD.*]*.*;,[DEB.*]*.*;,[DIM.*]*.*;,[ERR.*]*.*;,[MC.*]*.*;,[PIPM.*]*.*;,[PRC.*]*.*;,[SAD.*]*.*;,[SOC.*]*.COM;,[SOC.*]*.EXE;,[SOC.*]UISBG_GENERIC.DAT;,[SOC.*]*.RLB;,[UTL.*]*.*;,[SOC.*]*MEXICO*.DAT;/EXCLUDE=SADCONFIG*.COM MKA200:SOCSW.SAVOperating system: OpenVMS VAX version V5.5BACKUP version: V5.5-2CPU ID register: 0B000006Node name: EARTH::Written on: _EARTH$MKA200:Block size: 8192Group size: 10Buffer count: 36

Appendix E Documents included in 80158

TITLE NUMBER VERSION

Operator Guide A4-OPG-003076 3.23Config Guide A4-SCG-003076-1 3.9ACSE System Manual A4-OMM-003076 4.2X25 and Async. IFD A4-IFD-003076-1 3.9FAX IFD A4-IFD-003076-4 2.10Satellite Driver IFD A4-IFD-003076-5 3.7Reporting Data Formats IFD A4-IFD-003076-6 3.0Billing Tape Format IFD A4-IFD-003076-7 3.4

Appendix F Software Copyright Notice

This software release is furnished pursuant to a contract between Hughes Network Systems Limited and Telecomunicaciones de Mexico. This software release may only be used in the manner specified in that contract, unless such software is, or lawfully becomes, available in the public domain, or is, or lawfully becomes available to the user on other terms.

HUGHES NETWORK SYSTEMS EUROPESunrise Parkway Linford WoodMilton KeynesMK14 6LS EnglandTel: +44 (0) 1908 425300 Registered in England No. 1508514 Fax: +44 (0) 1908 425301 VAT Registration No. 354 0273 76

SOFTWARE SHIPPING FORM

THIS DOCUMENT IS FOR SHIPPING PURPOSES ONLY AND DOES NOT AUTHORISE THE RELEASE OR INSTALLATION OF ANY SOFTWARE AT ANY TIME

Customer: TELECOMUNICACIONES DE MEXICO

Sales order DC: 5376

Contact: Mr A.A.Castillo See attached Copyright Proprietary Notice

Software release: 80158 Raised by: M.J.Franklin

Software item: LES EXECUTABLES Date: 8/4/23

Description CCN Value each (£) Qty Value (£)

Mag tape: TK 852440 10 00 23.00 2 46.00

Mag. tape: DAT 852440 10 00 10.00 2 20.00

Mag tape: Travan 852440 10 00 10.00

Mag tape: 2400 ft 852440 10 00 4.00

Mag tape: 600 ft 852440 10 00 2.00

Diskette: 3.5 inch 852320 90 10 1.00

CD 852320 90 90 1.00 2 2.00

Other:

Total value (£'s) = 68.00

To be completed by the HNS Ltd Sales Order Administrator (Support)

Dispatch Reference: Export Licence Reference:

Consignee Address:

Telecomunicaciones de Mexico,CONTEL,Av. de las Telecomunicaciones S/N,Col. Leyes de ReformaIZTAPALAPA,09300 Mexico D.F.MEXICO

Signature: Date:

HNS FORM 1200 ISSUE H FEB '00 COP 0002

HUGHES NETWORK SYSTEMS EUROPESunrise Parkway Linford WoodMilton KeynesMK14 6LS EnglandTel: +44 (0) 1908 425300 Registered in England No. 1508514 Fax: +44 (0) 1908 425301 VAT Registration No. 354 0273 76

This software release is furnished pursuant to a contract between Hughes Network Systems Limited and Telecomunicaciones de Mexico. This software release may only be used in the manner specified in that contract, unless such software is, or lawfully becomes, available in the public domain, or is, or lawfully becomes available to the user on other terms.

HNS FORM 1200 ISSUE H FEB '00 COP 0002

Telecomunicaciones de Mexico

BAPREL 80158

060921

Telecomunicaciones de Mexico BAP

REL 80158 060921

Telecomunicaciones de Mexico SOC

REL 80158 060921

DOMESTIC L-BAND MDS


DOMESTIC L-BAND MDS



DOMESTIC L-BAND MDS


BAP REL 80158 060921

Telecomunicaciones de Mexico BAP REL 80158 060921
