72 quadcycler deck parts manual - hustler turf · pdf file339622 10/08 1-1 chapter 1 general...
TRANSCRIPT
•••••••Hustler Turf Equipment
•••••P.O. Box 7000
•••Hesston, Kansas
•67062-2097
72" QuadcyclerTM DeckParts Manual
t-2 399622 10/08
IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or operate this engine on any forest-covered, brush-covered, or grass-covered unimproved land. Other states or federal areas may have similar laws.
This spark ignition system complies with Canadian ICES-002.
The Engine Owner’s Manual provides information regarding the U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.
Keep Engine Owner’s Manual with your unit. Should the Engine Owner’s Manual become damaged or illegible, re-place immediately. Replacements may be ordered per the information found in the Product Information section of the owner’s manual.
The engine exhaust from this product contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive harm.
WARNING:
399622 10/08 t-3
t-4 399622 10/08
339622 10/08 c-1
Table of Contents
Chapter 1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Chapter 2 Deck Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Deck Subassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4Spindle Assembly - 506212 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Chapter 3 Gauge Arm Assembly - 466888 . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2Gearbox Breakdown - 532861 (Agrigear)(Yellow) . . . . . . . . . . . . . 3-4Gearbox Breakdown - 532861 (Curtis)(Black) . . . . . . . . . . . . . . . . 3-6
Chapter 4 Air Deflector Kit - 470344 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2Flotation Kit - 469189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Chapter 5 Decal Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-1
c-2 339622 10/08
339622 10/08 1-1
Chapter 1
General Information
This manual covers 72” Quadcycler Deck model: 925107.
Frequently Ordered Parts
Service Literature
Note: When ordering parts, you must use the part number as shown for each part, not the index number. Always give the tractor model and serial number and the engine model and serial number to your parts and service representative.
Note: Items sold in bulk such as seals and hoses are sold by the foot.
Using this manual
Illustrations used were current at the time of printing, but subsequent production changes may cause your machine to vary slightly in detail. Excel Industries, Inc. reserves the right to redesign and change the machine as deemed neces-sary, without notification. If a change has been made to your machine which is not reflected in this parts manual, see your Hustler dealer for current information and parts.
PART NO. DESCRIPTION
084178 Double Angle V-Belt754853 24" Blade506212 Spindle Housing Assembly
PART NO DESCRIPTION
084210 72" Quadcycler Owner’s Manual033514 72” Quadcycler Deck Assembly Instructions
1-2 339622 10/08
Hardware Description Codes & Abbreviations
The following codes are used throughout this parts manual. Refer to this list when ordering parts.
Standard Torques
The following chart lists the standard torque values for the threaded fasteners found in this manual. Torque all cap screws, nuts and set screws to these values unless a different torque is shown in the Notes section next to the fastener.
NOTE:
Loctite 592 to be used on all pipe threads.Lubricate all grease zerks
ABBREVIATION DESCRIPTION
CB Carriage BoltCE Clevis PinCP Cotter PinCS Cap ScrewCW Cup Washer
FDRW Fender WasherFW Flat WasherHX Hex HeadID Inside DiameterLW Lock WasherMB Machine BushingMS Machine ScrewNT NutOD Outside DiameterSC Self Tapping Cap ScrewSH Socket HeadSB Shoulder BoltSS Set Screw
SIZE FT-LBS NM SIZE FT-LBS NM
.250 8.2 11.1 M3 1 1.3
.312 17 23 M4 2.2 3
.375 30 40 M5 4.5 6.1
.438 48 65 M6 7.7 10.4
.500 73 99 M8 18.5 25
.562 105 143 M10 37 50
.625 145 200 M12 64 87
.750 260 350 M16 160 215
.875 420 565 M20 320 4351.00 625 850 M24 555 750
339622 10/08 2-1
Chapter 2 Contents
Deck Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Deck Subassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Spindle Assembly - 506212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-2 339622 10/08
Deck Assembly
2
1
31
2
1920
22
23
17
18
21
9
10
11
33
8
87
3132
2526
27
2829
30
1615
20
12
6
13
78
36
14
924
39
19
1211
38
5
34
78
38
37
35
4
339622 10/08 2-3
Deck Assembly
NOTES:
1. Supplied with item 15 but may be ordered separately.2. See “Gauge Arm Assembly - 466888” on page 3-2 for breakdown.
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 075291 075291 2 CLAMPING KNOB2 076547 076547 2 FW .344 X .688 X .065 SAE ZN3 307124 307140 1 R/H DECK COVER4 307132 307157 1 L/H DECK COVER5 467126 467126 1 ADJUSTER ARM6 074252 074252 2 CS .50-13 X 1.50 HX G5 ZN7 017046 017046 7 LW .50 MEDIUM SPRING ZN8 008193 008193 7 NT .50-13 HX G5 ZN9 017137 017137 4 FW .560 X 1.370 X .109 SAE ZN
10 028274 028274 2 CB .50-13 X 1.50 FULL ZN11 058875 058875 2 MB .510 X .870 X .050 ZN12 025601 025601 1 CS .50-13 X 4.620 ZN13 467266 467266 1 RIGHT REAR DISCHARGE DOOR14 467241 467241 1 CENTER REAR DISCHARGE DOOR15 474445 474452 1 DEFLECTOR16 054528 054528 1 BUMPER17 074559 074559 1 GRIP18 467258 467258 1 HANDLE19 024927 024927 8 NT .25-20 HX G5 ZN20 017079 017079 5 FW .250 X .560 X .040 SAE ZN21 467274 467274 1 SIDE DISCHARGE COVER22 055939 055939 4 CS .25-20 X .750 HX G5 ZN23 089789 089789 4 FW .266 X .750 X .060 ZN24 017038 017038 6 LW .250 MEDIUM SPRING ZN25 056077 056077 2 CS .25-20 X 1.00 HX G5 ZN26 287649 287649 1 SIDE DISCHARGE CLIP27 315465 315465 1 CLIP PLATE28 035626 035626 4 NT 10-24 HX ZN29 056176 056176 4 LW #10 MEDIUM SPRING ZN30 758821 758821 2 OVER CENTER LATCH31 025320 025320 2 HP .091 X 1.875 ZN32 016048 016048 4 MS 10-24 X .625 TH SL ZN33 467118 467118 4 PLUG BUTTON34 467175 467175 1 R/H MULCHER BAFFLE35 467167 467167 1 L/H MULCHER BAFFLE36 016527 016527 2 CS .50-13 X 1.00 HX G5 ZN37 537175 480228 2 TIE DOWN BRACKET38 016816 016816 2 NT .250-20 HX FL LK ZNY39 N/A 466888 2 GAUGE ARM ASSEMBLY
2-4 339622 10/08
Deck Subassembly
4
1
4
2
3
3
72
3
7 11
12
13
16
5
6
19
17
1521
235
622
10
9
8
6
27
18
24
25
332635
5
20
20
1
5
28
31
2930
33
34
1314
32
36
56
2
5
339622 10/08 2-5
Deck Subassembly
NOTES:
1. Item 9, pulley, must be in the same horizontal plane as item 28, drive pulleys, within ± .03" tolerance.
2. Assemble item 29, spindle housing, so the grease zerk faces the front of the deck.
3. Torque to 65-75 Ft. Lbs.4. Item 4, gearbox, to be filled to center of sight gauge when changing oil,
with ISO VG 46 Oil or equivalent oil.
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 532820 467316 1 72" 4-WAY DECK ASSEMBLY2 074252 074252 8 CS .50-13 X 1.50 HX G5 ZN3 028118 028118 4 FW .620 X 1.00 X .134 ZN4 532861 466664 1 GEARBOX5 017046 017046 23 LW .50 MEDIUM SPRING ZN6 008193 008193 11 NT .50-13 HX G5 ZN7 036715 036715 2 WOODRUFF KEY8 467100 467100 1 GEARBOX SUPPORT9 467324 467324 1 PULLEY 8”
10 042051 042051 2 SS .375-16 X 1.00 SQ-HD ZN11 706168 706168 2 NT .375-16 HX JAM G5 ZN12 773242 773242 4 CS .437-14 X 1.250 HX G5 ZN13 773259 773259 8 FW .50 X 1.250 X .064/.104 SAE F436 ZN14 041707 041707 4 NT .437-14 HX G5 ZN15 068759 068759 4 CW .560 X 1.340 X .050 PN16 315291 315291 1 IDLER ARM BRACKET17 263517 263517 1 BEARING DISC18 078949 078949 1 CS .50-13 X 2.00 G5 ZN19 503748 503748 1 IDLER PULLEY20 017137 017137 6 FW .560 X 1.370 X .109 SAE ZN21 036384 036384 1 IDLER SPRING22 244384 244384 1 IDLER CHAIN23 017277 017277 1 CP .187 X 1.00 LG HML ZN24 084178 084178 1 DOUBLE ANGLE V-BELT25 078378 078378 3 CS .50-20 X 1.50 HX G5 ZN26 212076 212076 3 KEY .250 X .250 X 1.5027 504142 504142 3 DRIVE PULLEY 8"28 016527 016527 12 CS .50-13 X 1.00 HX G5 ZN29 506212 249318 3 SPINDLE HOUSING ASSEMBLY30 712372 712372 3 KEY .250 X .250 X .66031 035808 035808 3 BLADE SADDLE32 754853 754853 3 24" BLADE33 752386 752386 6 CW .515 X 2.250 X .204 ZN34 753798 753798 3 CS .50-20 X 1.750 HX G5 ZN35 705954 705954 2 CS .50-13 X 1.250 HX G5 ZN36 532887 466631 2 GAUGE ARM MOUNT
6
2-6 339622 10/08
5. To check proper blade alignment, both ends of center blade must align with both end of outer blades. When blade tips are closest together they must be within .20" vertically.
6. See “Spindle Assembly - 506212” on page 2-7 for breakdown.
339622 10/08 2-7
Spindle Assembly - 506212
INDEX
NO.SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 077123 N/A 2 BEARING2 712364 N/A 1 SPINDLE SHAFT3 034843 N/A 1 SPINDLE HOUSING4 012005 N/A 1 GREASE ZERK
1
2
3
1
4
2-8 339622 10/08
339622 10/08 3-1
Chapter 3 Contents
Gauge Arm Assembly - 466888. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Gearbox Breakdown - 532861 (Agrigear)(Yellow). . . . . . . . . . . . . . . 3-4
Gearbox Breakdown - 532861 (Curtis)(Black). . . . . . . . . . . . . . . . . . 3-6
3-2 339622 10/08
Gauge Arm Assembly - 466888
1
2
1
34
5
25 61
2
3
4
5
6
19 20
23
2522
24
26
7
215
4
8
10
9
11
1312
14
1110
17
1516
1827
339622 10/08 3-3
Gauge Arm Assembly - 466888
NOTES:
1. Pack wheel bearings thoroughly with grease before installing.2. Fill wheel hub cavity between bearings approximately 2/3 full with
grease.3. To adjust wheel bearing, raise wheel off floor, tighten item 16, nut, while
rotating the wheel, until there is a slight bind to be sure all bearing surfaces are in contact.Then back off nut 1/6-1/4 turn to nearest locking hole or sufficiently to allow wheel to rotate freely within limits of .001"-.010" (ref) end play. Lock nut at this position by installing cotter pin.
4. Fill cap 3/4 full with grease then press into wheel hub.5. Do not fully spread item 24, cotter pin, for quicker adjustment of
washers.6. Use as spares.
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 016527 016527 1 CS .50-13 X 1.00 HX G5 ZN2 017046 017046 1 LW .50 MEDIUM SPRING ZN3 344267 344267 1 FW .510 X 2.150 X .187 SPL ZN4 082180 082180 2 MB 1.00 X 1.50 X .049 PN5 077123 077123 2 BEARING6 310185 310185 1 SPACER7 532911 083584 1 GAUGE WHEEL ARM8 506428 506428 1 GAUGE WHEEL FORK9 049148 049148 1 OIL SEAL
10 049155 049155 2 BEARING11 049163 049163 2 BEARING CUP12 747410 747410 1 GAUGE WHEEL 6 X 3.513 019521 019521 1 VALVE STEM14 747402 747402 1 TIRE 13 X 5 X 615 048850 048850 1 MACHINE BUSHING16 048868 048868 1 NT .75-16 HXSL PN17 011387 011387 1 CP .125 X 1.250 LG HML ZN18 049171 049171 1 DUST CUP19 017350 017350 1 SS .25-20 X .250 SH BO20 466698 466698 1 GAUGE WHEEL ARM HANDLE21 315226 315226 1 HANDLE PIN22 466680 466680 1 LOCK LINKAGE23 315234 315234 1 LINKAGE PIN24 017277 017277 1 CP .187 X 1.00 LG HML ZN25 068759 068759 15 CW .560 X 1.340 X .050 PN26 466672 466672 1 LOCK PIN27 747428 747428 TIRE & WHEEL ASSEMBLY (INCLUDES ITEMS 11-14)
3-4 339622 10/08
Gearbox Breakdown - 532861 (Agrigear)(Yellow)
1
4
6
7
2
3
5
8
9 10
11
6
12
7
13
14
15
1819
76
20
21
1
2212
25
2324
16
17
7
6
339622 10/08 3-5
Gearbox Breakdown - 532861 (Agrigear)(Yellow)
NOTES:
1. Gearbox Gear Set (108884) is replacement set for Items 8 and 19.
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 036707 N/A 8 CS .312-18 X .875 HX G5 BO2 036046 N/A 1 RELIEF VALVE3 036731 N/A 1 REDUCER BUSHING4 036525 N/A 1 BEARING CAP5 036640 N/A 2 BEARING CAP SHIM6 036608 N/A 4 BEARING CUP7 036616 N/A 4 BEARING CONE8 034769 N/A 1 GEAR (25 TEETH)9 036715 N/A 1 WOODRUFF KEY
10 034736 N/A 1 GEAR SHAFT11 036673 N/A 1 GEAR SHAFT SPACER12 036624 N/A 2 SEAL13 N/A 1 CASE14 740829 N/A 1 SIGHT GLASS15 036665 N/A 2 SEAL CAP SHIM16 036558 N/A 1 SEAL CAP17 055939 N/A 4 CS .25-20 X .750 HX G5 ZN18 036632 N/A 2 CARRIER SHIM19 034751 N/A 1 PINION SHAFT (19 TEETH)20 036533 N/A 1 PINION CARRIER21 036681 N/A 1 LOCK WASHER22 036699 N/A 1 LOCK NUT23 036657 N/A 2 SEAL CAP SHIM24 036541 N/A 1 CARRIER SEAL CAP25 036723 N/A 4 MS 10-24 X .750 FT SH BO
108884 N/A 1 GEARBOX GEAR SET (NOT SHOWN)1
3-6 339622 10/08
Gearbox Breakdown - 532861 (Curtis)(Black)
1
7
12
10
2
5
8
11
8
7
13
15
18
23
22
25
15
20
9
1
87
87
14
11
4
6
2119
24
1617
3
339622 10/08 3-7
Gearbox Breakdown - 532861 (Curtis)(Black)
NOTES:
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 601738 N/A 8 SEMS CAP SCREW2 601735 N/A 1 RELIEF VALVE3 601736 N/A 1 BLANK CAP4 601732 N/A 1 GASKET (0.015)5 601733 N/A A/R GASKET (0.005)6 601734 N/A A/R GASKET (0.003)7 601745 N/A A/R BEARING CUP8 601744 N/A 4 BEARING CONE9 601731 N/A 1 GEAR (RH)
10 601751 N/A 1 THRU SHAFT11 601737 N/A 1 1/4 X .875 KEY12 N/A N/A 1 GEAR BOX HOUSING13 601755 N/A 1 SIGHT PLUG14 601752 N/A 1 SEAL15 601743 N/A 2 V-RING SEAL16 601750 N/A 1 RETAINING RING17 601749 N/A 1 PINION (LH)18 601742 N/A 1 HUB SHAFT19 601746 N/A A/R GASKET (0.015)20 601747 N/A A/R GASKET (0.005)21 601748 N/A A/R GASKET (0.003)22 N/A N/A 1 HUB23 601739 N/A 1 LOCKWASHER24 601740 N/A 1 LOCKNUT25 601741 N/A 1 SEAL
108884 N/A 1 GEARBOX GEAR SET (NOT SHOWN)
3-8 339622 10/08
339622 10/08 4-1
Chapter 4 Contents
Air Deflector Kit - 470344. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Flotation Kit - 469189. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4-2 339622 10/08
Air Deflector Kit - 470344
72" QUADCYCLER DECK
11
1
2
1
2
5
7
3
4
8
9
5
6
4
1
5
1
1
4
4
5
2
2
2
2
4
339622 10/08 4-3
Air Deflector Kit - 470344
NOTES:
1. After installation, the 3 air deflectors should be positioned .25" above blade tips.
2. Part installed when High Lift Bac Vac blower is used.
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 034280 N/A 7 CS .312-18 X .750 HX G5 ZN2 076547 N/A 9 FW .344 X .688 X .065 ZN3 471318 N/A 1 LEFT SIDE AIR DEFLECTOR4 017004 N/A 9 LW .312 MEDIUM SPRING ZN5 034272 N/A 9 NT .312-18 HX G5 ZN6 471292 N/A 1 CENTER AIR DEFLECTOR7 471300 N/A 1 RIGHT SIDE AIR DEFLECTOR8 079186 N/A 2 CS .312-18 X 1.250 HX G5 ZN9 471326 N/A 1 FILL PANEL
4-4 339622 10/08
Flotation Kit - 469189
72" QUADCYCLER DECK
18
14 13
12
15
7
16
1517
10
5
8 9
11
6
7
1
3
4
3
4
3
21
3
4
4
1
339622 10/08 4-5
Flotation Kit - 469189
NOTES:
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 705954 N/A 8 CS .50-13 X 1.250 HX G5 ZN2 533877 N/A 1 RIGHT SIDE CASTER ARM3 017046 N/A 8 LW .50 MEDIUM SPRING ZN4 008193 N/A 8 NT .50-13 HX G5 ZN5 527788 N/A 1 LEFT SIDE CASTER ARM6 078634 N/A 2 LINCH PIN7 045765 N/A 4 FW 1.060 X 1.50 X .134 ZN8 015495 N/A 2 GREASE FITTING9 018747 N/A 4 BRONZE BUSHING
10 469924 N/A 4 SPACER .25011 469882 N/A 2 SPACER .5012 469916 N/A 6 SPACER 1.0013 470674 N/A 2 CASTER MOUNT14 089938 N/A 2 CS .50-13 X 4.00 HX G5 ZN15 025296 N/A 4 FW .760 X 1.625 X .080 ZN16 025288 N/A 2 CASTER WHEEL17 025262 N/A 2 SPANNER BUSHING18 023317 N/A 2 NT .50-13 UNT LK G5 ZN
4-6 339622 10/08
Flotation Kit - 469189
72‘” QUADCYCLER DECK
SPRINGBRACKET
9
5
7
8
3
2
106
4
1
339622 10/08 4-7
Flotation Kit - 469189
NOTES:
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 036236 N/A 2 CS .312-18 X 1.00 HX G5 ZN2 470708 N/A 1 TIGHTENER3 034272 N/A 2 NT .312-18 HX G5 ZN4 025502 N/A 1 SPRING TIGHTENER5 334052 N/A 1 LOWER SPRING MOUNT6 735670 N/A 1 TIGHTENER DECAL7 011379 N/A 3 DECK SPRING8 370452 N/A 1 UPPER SPRING MOUNT9 023036 N/A 3 HAIRPIN
10 370494 N/A 2 DECK SPRING STRAP
4-8 339622 10/08
Flotation Kit - 469189
2
72" QUADCYCLER DECK
4
1
EXISTINGHARDWARE
EXISTINGHARDWARE
5
21
34
3
339622 10/08 4-9
Flotation Kit - 469189
NOTES:
1. Discard lock washer and move nut to location shown.
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 728550 N/A 2 SB .50 X .750 SH .375-16 TD ZN2 058875 N/A 8 MB .510 X .870 X .050 ZN3 712919 N/A 4 FW .406 X 1.00 X .120 HRD ZN4 016865 N/A 4 NT .375-16 UNT LK ZN5 740878 N/A 2 SB .50 X 1.00 SH .375-16 TH
4-10 339622 10/08
339622 10/08 5-1
Chapter 5 Contents
Decal Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5-2 339622 10/08
Decal Group
1
4
7
.50
.25
.25
2.0
8.0
1.0
1.50
1.50
8.0
20.0710.25
3.02.0
1.0
1.0.50
8.0
1
1
1
LOCATE ALONG CORNER& EDGE OF STRINGERAS SHOWN (2 PLACES)
5
3
2
9
10
11
8
5
21
6
339622 10/08 5-3
Decal Group
NOTES:
1. .25" between decals
INDEX NO.
SERVICE PART NO.
MFG. PART NO. QTY. DESCRIPTION
1 727438 727438 3 WHIRLING BLADES DECAL2 359547 359547 2 STEP TREAD3 760637 760637 1 MOWER DECK QUICK REFERENCE DECAL4 727842 727842 1 PTO SHAFT DECAL5 727453 727453 2 BELT & PULLEY DECAL6 728519 728519 1 HUSTLER LOGO DECAL7 727685 727685 1 72” 4-WAY DECK DECAL8 727917 727917 1 PATENT NUMBER DECAL9 741264 741264 1 MADE IN U.S.A. DECAL
10 727420 727420 1 DEFLECTOR SHIELD DECAL11 N/A 083279 1 SERIAL NUMBER PLATE12 757112K N/A 1 DECAL KIT (INCLUDES ITEMS 1-12)
5-4 339622 10/08
399622 10/08 r-1
NOTES:
r-2 399622 10/08
339622 10/08 i-1
Numerical IndexPart PageNo. No.
Part PageNo. No.
Part PageNo. No.
IndexNumerics008193 2-3, 2-5, 4-5011379 4-7011387 3-3012005 2-7015495 4-5016048 2-3016527 2-3, 2-5, 3-3016816 2-3016865 4-9017004 4-3017038 2-3017046 2-3, 2-5, 3-3, 4-5017079 2-3017137 2-3, 2-5017277 2-5, 3-3017350 3-3018747 4-5019521 3-3023036 4-7023317 4-5024927 2-3025262 4-5025288 4-5025296 4-5025320 2-3025502 4-7025601 2-3028118 2-5028274 2-3033514 1-1034272 4-3, 4-7034280 4-3034736 3-5034751 3-5034769 3-5034843 2-7035626 2-3035808 2-5036046 3-5036236 4-7036384 2-5036525 3-5036533 3-5036541 3-5036558 3-5036608 3-5036616 3-5036624 3-5036632 3-5036640 3-5036657 3-5
036665 3-5036673 3-5036681 3-5036699 3-5036707 3-5036715 2-5, 3-5036723 3-5036731 3-5041707 2-5042051 2-5045765 4-5048850 3-3048868 3-3049148 3-3049155 3-3049163 3-3049171 3-3054528 2-3055939 2-3, 3-5056077 2-3056176 2-3058875 2-3, 4-9068759 2-5, 3-3074252 2-3, 2-5074559 2-3075291 2-3076547 2-3, 4-3077123 2-7, 3-3078378 2-5078634 4-5078949 2-5079186 4-3082180 3-3083279 5-3083584 3-3084178 1-1, 2-5084210 1-1089789 2-3089938 4-5108884 3-7212076 2-5244384 2-5249318 2-5263517 2-5287649 2-3307124 2-3307132 2-3307140 2-3307157 2-3310185 3-3315226 3-3315234 3-3
315291 2-5315465 2-3334052 4-7344267 3-3359547 5-3370452 4-7370494 4-7466631 2-5466664 2-5466672 3-3466680 3-3466698 3-3466888 2-3467100 2-5467118 2-3467126 2-3467167 2-3467175 2-3467241 2-3467258 2-3467266 2-3467274 2-3467316 2-5467324 2-5469189 4-4, 4-5, 4-6, 4-7, 4-
8, 4-9469882 4-5469916 4-5469924 4-5470344 4-2, 4-3470674 4-5470708 4-7471292 4-3471300 4-3471318 4-3471326 4-3474445 2-3480228 2-3503748 2-5504142 2-5506212 1-1, 2-5506428 3-3527788 4-5532820 2-5532861 2-5, 3-4, 3-5, 3-6, 3-7532887 2-5532911 3-3533877 4-5537175 2-3601731 3-7601732 3-7601733 3-7
Part PageNo. No.
Part PageNo. No.
Part PageNo. No.
i-2 339622 10/08
601734 3-7601735 3-7601736 3-7601737 3-7601738 3-7601739 3-7601740 3-7601741 3-7601742 3-7601743 3-7601744 3-7601745 3-7601746 3-7601747 3-7601748 3-7601749 3-7601750 3-7
601751 3-7601752 3-7601755 3-7705954 2-5, 4-5706168 2-5712364 2-7712372 2-5712919 4-9727420 5-3727438 5-3727453 5-3727685 5-3727842 5-3727917 5-3728519 5-3728550 4-9735670 4-7
740829 3-5740878 4-9741264 5-3747402 3-3747410 3-3747428 3-3752386 2-5753798 2-5754853 1-1, 2-5757112K 5-3758821 2-3760637 5-3773242 2-5773259 2-5925107 1-1