7 trim and upholstery - cars.usoft.czcars.usoft.cz/soubory/manualy/fluence7.pdffluence - megane...

© Renault s.a.s 2007

"The repair procedures given by the manufacturer in this document are based on thetechnical specifications current when it was prepared.

The procedures may be modified as a result of changes introduced by the manufacturer inthe production of the various component units and accessories from which the vehicles areconstructed".

All rights reserved by Renault.

Copying or translating, in part or in full, of this document or use of the service part referencenumbering system is forbidden without the prior written authority of Renault.

OCTOBER 2009 EDITION ANGLAISE

X38, and B32 or L38

7 Trim and upholstery

71A BODY INTERNAL TRIM

72A SIDE OPENING ELEMENT TRIM

73A NON-SIDE OPENING ELEMENTS TRIM

75A FRONT SEAT FRAMES AND MECHANISMS

76A REAR SEAT FRAMES AND MECHANISMS

77A FRONT SEAT TRIM

78A REAR SEAT TRIM

79A SEAT ACCESSORIES

FLUENCE - MEGANE GENERATION -Section 7

Contents

Pages

FLUENCE - MEGANE GENERATION - Section 7 ContentsPages

71A BODY INTERNAL TRIM

Floor carpet: Removal - Refitting 71A-1

Headlining: Removal - Refitting 71A-3

Front door sill lining: Removal - Refitting 71A-12

B-pillar lower trim: Removal - Refitting 71A-14

Rear door sill lining: Removal - Refitting 71A-15

Rear wheel arch trim: Removal - Refitting 71A-17

Windscreen pillar trim: Removal - Refitting 71A-18

B-pillar upper trim: Removal - Refitting 71A-19

Quarter panel trim: Removal - Refitting 71A-22

Rear panel lining: Removal - Refitting 71A-24

Rear parcel shelf side trim: Removal - Refitting 71A-25

72A SIDE OPENING ELEMENT TRIM

Front side door trim: Removal - Refitting 72A-1

Rear side door trim: Removal - Refitting 72A-4

73A NON-SIDE OPENING ELEMENTS TRIM

Tailgate trim: Removal - Refitting 73A-1

Luggage compartment lid trim: Removal - Refitting 73A-2

75AFRONT SEAT FRAMES AND MECHANISMS

Front seat base frame: Removal - Refitting 75A-1

Front seatback frame: Removal - Refitting 75A-2

Front seat runner: Removal - Refitting 75A-4

Front seat height adjuster control: Removal - Refitting 75A-6

Front seat height adjustment: Removal - Refitting 75A-8

Front seat lumbar adjustment: Removal - Refitting 75A-9

Front seat lumbar adjustment control: Removal - Refitting 75A-11

Front seat backrest tilt control: Removal - Refitting 75A-12

Complete front seat: Removal - Refitting 75A-13

Contents

76A REAR SEAT FRAMES AND MECHANISMS

Rear bench seatback: Removal - Refitting 76A-1

Rear bench seat base: Removal - Refitting 76A-4

Rear bench seat mechanism: Removal - Refitting 76A-6

77A FRONT SEAT TRIM

Front seat base trim: Removal - Refitting 77A-1

Front seatback trim: Removal - Refitting 77A-4

Front seat lower casing: Removal - Refitting 77A-12

78A REAR SEAT TRIM

1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A-1

Rear bench seat base trim: Removal - Refitting 78A-7

79A SEAT ACCESSORIES

Front headrest: Removal - Refitting 79A-1

Front seat headrest guide: Removal - Refitting 79A-4

Front armrest: Removal - Refitting 79A-6

Rear centre armrest: Removal - Refitting 79A-7

Rear bench seat headrest guide: Removal - Refitting 79A-8

Rear bench seat headrest: Removal - Refitting 79A-10

71A-1

BODY INTERNAL TRIMFloor carpet: Removal - Refitting 71A

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).

a Remove:

- the front seats completely (see 75A, Front seatframes and mechanisms, Complete front seat:Removal - Refitting, page 75A-13) ,

- the central console (see Centre console: Remov-al - Refitting) (57A, Interior equipment).

a Remove the single unit rear bench seat base (seeSingle unit rear bench seat base: Removal - Re-fitting) .

a Remove the 1/3 and 2/3 rear bench seat base (see1/3 and 2/3 rear bench seat base: Removal - Re-fitting) .

a Remove:

- the front door sill lining (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,page 71A-12) ,

- the rear door sill lining (see 71A, Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-15) ,

- the rear inner sill upper trim (see Rear inner sillupper trim: Removal - Refitting) ,

- the B-pillar lower trim (see 71A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-14) .

II - OPERATION FOR REMOVAL OF PART CONCERNED

a Remove:

- the clips (1) ,

- the mounting supports of the rear bench seat base(2) .

a Remove the clips (3) .

FOLDING REAR BENCH SEAT

1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK

136664

135098

71A-2

BODY INTERNAL TRIMFloor carpet: Removal - Refitting 71A

a Unclip the clip (4) .

a Remove:

- the accelerator pedal stop (5) ,

- the floor carpet.

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

a Refit:

- the floor carpet,

- the accelerator pedal stop (5) ,

- the clips (4) , (3) and (1) ,

- the mounting supports of the rear bench seat base(2) .

II - FINAL OPERATION

a Refit:

- the B-pillar lower trim (see 71A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-14) ,


- the rear door sill lining (see 71A, Body internaltrim, Rear door sill lining: Removal - Refitting,page 71A-15) ,

- the front door sill lining (see 71A, Body internaltrim, Front door sill lining: Removal - Refitting,page 71A-12) .

a Refit the 1/3 and 2/3 rear bench seat base (see 1/3and 2/3 rear bench seat base: Removal - Refit-ting) .

a Refit the single unit rear bench seat base (see Sin-gle unit rear bench seat base: Removal - Refit-ting) .

a Refit:

- the central console (see Centre console: Remov-al - Refitting) (57A, Interior equipment),

- the front seats completely (see 75A, Front seatframes and mechanisms, Complete front seat:Removal - Refitting, page 75A-13) .

a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).

136661

135097



71A-3

BODY INTERNAL TRIMHeadlining: Removal - Refitting

B32

71A

REMOVAL



a Remove the sunroof switch (see Sunroof switch:Removal - Refitting) (52A, Non-side opening ele-ment mechanisms).

a Remove:

- the interior lights (see Interior light: Removal -Refitting) (81B, Interior lighting),

- the sun visors (see Sun visor: Removal - Refit-ting) (57A, Interior equipment),

- the courtesy lights (see Courtesy light: Removal -Refitting) (81B, Interior lighting),

- the grab handles (see Grab handle: Removal -Refitting) (57A, Interior equipment),

- the windscreen pillar trims (see 71A, Body inter-nal trim, Windscreen pillar trim: Removal - Re-fitting, page 71A-18) .

a Disconnect the connector (1) from the headliningwiring.

a Disconnect the sunroof wiring connectors.

Special tooling required

Car. 1363 Set of tr im removal levers.

IMPORTANT

To avoid all risk of damage to the systems, apply the safety and cleanliness instructions and opera-tion recommendations before carrying out any repair:

- (see Airbag and pretensioners: Precautionsfor the repair) (88C, Airbag and pretensioners),

- (see Vehicle: Precautions for the repair) (01D,Mechanical introduction).

ELECTRIC SUNROOF

137500

ELECTRIC SUNROOF

71A-4


B32

71A

a Remove:

- the upper cover of the interior rear view mirror (3)using the tool (Car. 1363),

- the lower cover of the interior rear view mirror.

a Disconnect the connectors (4) on the interior rearview mirror.

a Mark the positioning of the finishing seals.

a Remove the finishing seals (5) .

a Remove the single unit rear bench seat base (seeSingle unit rear bench seat base: Removal - Re-fitting) .

a Remove the 1/3 and 2/3 rear bench seat base (see1/3 and 2/3 rear bench seat base: Removal - Re-fitting) .

a Remove:

- the side door seals partially,

- the luggage compartment seal partially,

- the B-pillar lower trims (see 71A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-14) ,

137004

137003

ELECTRIC SUNROOF

137172



71A-5


B32

71A- the B-pillar upper trims (see 71A, Body internaltrim, B-pillar upper trim: Removal - Refitting,page 71A-19) ,

- the rear parcel shelf side trim panels (see 71A,Body internal trim, Rear parcel shelf side trim:Removal - Refitting, page 71A-25) ,

- the rear quarter panel trims (see 71A, Body inter-nal trim, Quarter panel trim: Removal - Refit-ting, page 71A-22) .


a Unclip the rear mountings.

a Unclip the headlining front section (6) .

a Unclip the headlining central section (7) .

a Remove the headlining (this operation requires twopeople).

a

137511

137174

137482

137175

ELECTRIC SUNROOF

Note:

For vehicles equipped with a sunroof, the head-lining must be handled with care. The side edgesare weakened by the design of the sunroof.

71A-6


B32

71AREFITTING

I - REFITTING PREPARATION OPERATION

a Check the presence and the condition of the velcrostrips (8) .

II - REFITTING OPERATION FOR PART CONCERNED

a

a Fit the headlining (this operation requires two peo-ple).

a Clip on:

- the headlining central section,

- the headlining front section.

III - FINAL OPERATION

a Refit:

- the rear quarter panel trims (see 71A, Body inter-nal trim, Quarter panel trim: Removal - Refit-ting, page 71A-22) ,

- the rear parcel shelf side trim panels (see 71A,Body internal trim, Rear parcel shelf side trim:Removal - Refitting, page 71A-25) ,

- the B-pillar upper trims (see 71A, Body internaltrim, B-pillar upper trim: Removal - Refitting,page 71A-19) ,

- the B-pillar lower trims (see 71A, Body internaltrim, B-pillar lower trim: Removal - Refitting,page 71A-14) ,

- the side door seals,

- the luggage compartment seal.

a Refit the 1/3 and 2/3 rear bench seat base (see 1/3and 2/3 rear bench seat base: Removal - Refit-ting) .

137482

137483

ELECTRIC SUNROOF

Note:



71A-7


B32

71A

a Refit the single unit rear bench seat base (see Sin-gle unit rear bench seat base: Removal - Refit-ting) .

a Refit the finishing seal.

a Connect the connectors on the interior rear view mir-ror.

a Clip on:

- the lower trim of the rear view mirror cover,

- the upper trim of the rear view mirror cover.

a Connect the headlining wiring connector.

a Connect the sunroof wiring connectors.

a Refit:

- the windscreen pillar trims (see 71A, Body inter-nal trim, Windscreen pillar trim: Removal - Re-fitting, page 71A-18) ,




- the interior lights (see Interior light: Removal -Refitting) (81B, Interior lighting).

a Refit the sunroof switch (see Sunroof switch: Re-moval - Refitting) (52A, Non-side opening elementmechanisms).

a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).


ELECTRIC SUNROOF

ELECTRIC SUNROOF

ELECTRIC SUNROOF

71A-8


L38

71A

REMOVAL

I - PREPARATION OPERATION


a Remove:


- the interior lights (see Interior light: Removal -Refitting) (81B, Interior lighting),



- the windscreen pillar trims (see 71A, Body inter-nal trim, Windscreen pillar trim: Removal - Re-fitting, page 71A-18) .

a Disconnect the connector (1) from the headliningwiring.

a Remove interior rear view mirror (see Interior rear-view mirror: Removal - Refitting) .



IMPORTANT

To avoid all risk of damage to the systems, apply the safety and cleanliness instructions and opera-tion recommendations before carrying out any repair:

- (see Airbag and pretensioners: Precautionsfor the repair) (88C, Airbag and pretensioners),

- (see Vehicle: Precautions for the repair) (01D,Mechanical introduction).

137500

71A-9


L38

71A

a Mark the positioning of the finishing seal (2) .

a Remove the finishing seal (3) .

a Partially remove the side door seals.

a Remove:

- the B-pillar upper trims (see 71A, Body internaltrim, B-pillar upper trim: Removal - Refitting,page 71A-19) ,

- the rear quarter panel trims (see 71A, Body inter-nal trim, Quarter panel trim: Removal - Refit-ting, page 71A-22) .

II - REMOVAL OPERATION

a Unclip:

- the clip (4) using the tool (Car. 1363),

- the rear mountings at (5) .

a Disconnect:

- the speaker connector,

- the connector of the sunroof wiring.

a Unclip the headlining front section (6) .

ELECTRIC SUNROOF

137503

144086

144071

ELECTRIC SUNROOF

144089

71A-10


L38

71A

a Unclip the headlining central section (7) .

a

a Remove the headlining (this operation requires twopeople).

REFITTING


a Check the presence and the condition of the velcrostrips (8) .

144090

ELECTRIC SUNROOF

Note:


144087

144088

71A-11


L38

71AII - REFITTING OPERATION

a

a Proceed in the reverse order to removal.

ELECTRIC SUNROOF

Note:


71A-12

BODY INTERNAL TRIMFront door sill lining: Removal - Refitting 71A

REMOVAL


a Remove:

- the front side door seal partially,

- the bonnet release control (1) from the left-handside, using the tool (Car. 1363),



a Remove the front door sill lining (2) , using the tool(Car. 1363) .



138756

138755

71A-13

BODY INTERNAL TRIMFront door sill lining: Removal - Refitting 71A

a Remove the A-pillar lower trim (3) using the tool(Car. 1363).

REFITTING


a Refit:

- the A-pillar lower trim (3) ,

- the front door sill lining (2) .


a Refit:


- the bonnet release control (1) from the left-handside,

- the front side door seal.

138757

137117

71A-14

BODY INTERNAL TRIMB-pillar lower trim: Removal - Refitting 71A

REMOVAL


a Partially remove the front and rear side door seals.


a Remove the B-pillar lower trim at (1) and (2) .

REFITTING


a Refit the B-pillar lower trim.


a Refit the front and rear side door seals.

137107

137109

71A-15

BODY INTERNAL TRIMRear door sill lining: Removal - Refitting 71A

REMOVAL


a Remove:


- the rear inner sill upper trim (see Rear inner sillupper trim: Removal - Refitting) .


a Remove:

- the clip (1) ,

- the rear door sill lining at (2) .

REFITTING


a Refit the rear door sill lining.

137099

137102

71A-16

BODY INTERNAL TRIMRear door sill lining: Removal - Refitting 71A

a Refit the clip (1) .


a Refit:



71A-17

BODY INTERNAL TRIMRear wheel arch trim: Removal - Refitting

B32

71AREMOVAL


a Remove:

- the rear end panel lining (see Rear end panel lin-ing: Removal - Refitting) ,

- the rear inner sill upper trim (see Rear inner sillupper trim: Removal - Refitting) .

a Remove the rear parcel shelf side trim (see 71A,Body internal trim, Rear parcel shelf side trim:Removal - Refitting, page 71A-25) .


a Remove the rear wheel arch trim (1) .

REFITTING


a Refit the rear wheel arch trim.


a Refit the rear parcel shelf side trim (see 71A, Bodyinternal trim, Rear parcel shelf side trim: Remov-al - Refitting, page 71A-25) .

a Refit:


- the rear end panel trim (see Rear end panel lin-ing: Removal - Refitting) .

137096

71A-18

BODY INTERNAL TRIMWindscreen pillar trim: Removal - Refitting 71A

REMOVAL


a Partially remove the front side door seal.


a Partially unclip the windscreen pillar trim at (1) usingthe tool (Car. 1363).

a Remove the windscreen pillar trim at (2) .

REFITTING


a Insert the lower section of the windscreen pillar trim.

a Clip on the entire length of the A-pillar trim.


a Refit the front side door seal.



138799

138800

71A-19

BODY INTERNAL TRIMB-pillar upper trim: Removal - Refitting 71A

REMOVAL


a Remove the B-pillar lower trim (see 71A, Body in-ternal trim, B-pillar lower trim: Removal - Refit-ting, page 71A-14) .

a Unclip the trim by pressing on the locking clips (1)using a flat-blade screwdriver.

a Remove the trim (2) .

Tightening torquesm

bolt of the front sideseat belt return mecha-nism

21 N.m

139020

139018

71A-20


a Remove:

- the bolt (3) ,

- the front side seat belt return mechanism.

a Remove:

- the bolt (4) ,

- the guide of the front side seat belt return mecha-nism.


a Use a flat-blade screwdriver to press at (7) to re-lease the lower section of the trim.

a Remove the clips (9) .

a Unclip the lower section of the B-pillar upper trim.

137457

137036

137438

137072

71A-21


a Remove the B-pillar upper trim at (10) and (11) .

REFITTING


a Refit the B-pillar upper trim.

a Clip on the lower section of the trim at (7) .


a Refit the guide of the front side seat belt returnmechanism.

a Refit the front side seat belt return mechanism.

a Torque tighten the bolt of the front side seat beltreturn mechanism (21 N.m).

a Refit:

- the trim of the front side seat belt return mecha-nism,


139024

71A-22

BODY INTERNAL TRIMQuarter panel trim: Removal - Refitting

B32

71A

REMOVAL


a Remove:

- the rear parcel shelf side trim (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-25) ,


- the bolt of the rear side seat belt lower mounting.


a Remove the rear quarter panel trim (3) .

REFITTING


a Refit the rear quarter panel trim.


a Torque tighten the bolt of the rear side seat beltlower mounting (21 N.m).

a Refit:


- the rear parcel shelf side trim (see 71A, Body in-ternal trim, Rear parcel shelf side trim: Removal- Refitting, page 71A-25) .

Tightening torquesm

bolt of the rear side seatbelt lower mounting

21 N.m

137451

137450

71A-23

BODY INTERNAL TRIMQuarter panel trim: Removal - Refitting

L38

71AREMOVAL


a Tilt the rear bench seatback.

a Partially unclip the rear door sill upper trim (see Rearinner sill upper trim: Removal - Refitting) .


a Remove the rear quarter panel trim (1) .

REFITTING

I - REFITTING OPERATION

a Refit the rear quarter panel trim.


a Clip on the rear door sill upper trim (see Rear innersill upper trim: Removal - Refitting) .

a Fit the rear bench seatback.

143767

143766

71A-24

BODY INTERNAL TRIMRear panel lining: Removal - Refitting

L38

71A

REMOVAL


a Tilt:

- the rear bench seat base,

- the rear bench seatback.

a Remove:


- partially the rear side door seal,

- the luggage compartment seal partially,

- the luggage compartment carpet.


a Remove:

- the clips (1) using the tool (Car. 1363),

- the trim (2) using the tool (Car. 1363),

- the rear panel trim.

REFITTING


a Always check the condition of the clips and replacethem if necessary.

II - REFITTING OPERATION




144143

71A-25

BODY INTERNAL TRIMRear parcel shelf side trim: Removal - Refitting

B32

71AREMOVAL


a Partially remove the tailgate seal.

a Pull down the rear bench seatback.

a Remove the rear parcel shelf.

a Remove the luggage compartment light (see Lug-gage compartment light: Removal - Refitting)(81B, Interior lighting).


a Remove:

- the bolts (1) ,

- the rear parcel shelf side trim (2) .

REFITTING


a Refit the rear parcel shelf side trim.


a Refit the luggage compartment light (see Luggagecompartment light: Removal - Refitting) (81B, In-terior lighting).

a Refit the rear parcel shelf.

a Lock the rear bench seatback in place.

a Refit the tailgate seal.

137439

137441

72A-1

SIDE OPENING ELEMENT TRIMFront side door trim: Removal - Refitting 72A

REMOVAL


a Remove the trim of the front side door handle usingthe tool (Car. 1363) by inserting it at (1) .

a Remove the rear view mirror interior trim.

a Remove the blanking cover (4) .



EQUIPMENT LEVEL EA3 or EQUIPMENT LEVELEA4

137392

137394

139034

72A-2



a Remove the bolts (5) .

a Remove the bolts (5) .

a Unclip the front side door trim.

a Disconnect:

- the connectors of the front side door window con-trol switch plate,

- the front side door light.


137407


137405

139012

72A-3


a Unclip the front side door interior opening control ca-ble.

a Remove the front side door trim.

REFITTING


a parts always to be replaced: Front side openingelement trim clip (70,03,02,22).


a Fit the front side door trim.

a Connect:

- the connectors of the front side door window con-trol switch plate,

- the front side door light.

a Clip on the front side door interior opening releasecable.

a Clip on the front side door trim.

a Refit the bolts (5) .


a Refit the blanking cover (4) .

a Refit the door mirror interior trim.

a Refit the front side door handle trim.

a Carry out a function test.


72A-4

SIDE OPENING ELEMENT TRIMRear side door trim: Removal - Refitting

B32

72AREMOVAL


a Pull the ring towards the vehicle interior (1) .


a Remove the manual window winder control handle.

MANUAL REAR WINDOW

137399

137400

137396

137398

72A-5


B32

72A

a Remove the bolt (3) from the rear side door trim.

a Remove:

- the blanking cover (6) ,

- the bolt (7) .


a Unclip:

- the rear side door trim,

- the interior opening release cable of the rear sidedoor.

a Disconnect the connectors from the rear side doorwindow control switch plate.

a Disconnect the tweeter speaker.

142218

139034

139015

ELECTRIC REAR WINDOW

RADIO 03A or RADIO 05A

72A-6


B32

72A

a Remove the rear side door trim.

REFITTING


a parts always to be replaced: Rear side openingelement trim clip (70,03,02,23).


a Partially refit the rear side door trim.

a Connect the tweeter speaker.

a Connect the connectors to the rear side door win-dow control switch plate.

a Clip on:

- the interior opening release cable of the rear sidedoor,

- the rear side door trim.


a Refit:

- the bolt (7)

- the blanking cover (6) .

a Refit the bolt (3) of the rear side door trim.

a Clip on the clip (2) .

a Refit the manual window winder control handle.


139016

RADIO 03A or RADIO 05A

ELECTRIC REAR WINDOW

MANUAL REAR WINDOW

Note:

Refit the manual window winder handle for therear side door in a vertical position with the but-ton at the bottom.

72A-7


L38

72A

REMOVAL


a Pull the ring towards the vehicle interior (1) .


a Remove the manual window winder control handle.



MANUAL REAR WINDOW

137399

137400

137396

137398

72A-8


L38

72A

a Remove:

- the side bolt of the rear side door trim (3) ,

- the blanking cover (4) ,

- the bolt of the rear side door opening handle,

- the rear side door opening handle (5) .

a Unclip the window winder plate of the rear side doorusing the tool (Car. 1363).

a Disconnect the connector of the rear side door win-dow winder.


a Partially unclip the rear side door trim using unclip-ping pliers at (6) .

a Disconnect the connector from the rear side doortweeter.

a Remove the rear side door trim.

REFITTING


a parts always to be replaced: Rear side openingelement trim clip (70,03,02,23).


a Fit the rear side door trim.

a Refit the rear side door opening handle.

a Connect:

- the connector of the rear side door tweeter,

- the connector of the rear side door window winder.

a Clip on:

- the rear side door window winder plate,

- the rear side door trim.

143835

136968

140837

72A-9


L38

72AIII - FINAL OPERATION

a Refit the manual window winder control handle.

a Pull the ring (1) .



MANUAL REAR WINDOW

Note:

Refit the manual window winder handle for therear side door in a vertical position with the but-ton at the bottom.

73A-1

NON-SIDE OPENING ELEMENTS TRIMTailgate trim: Removal - Refitting

B32

73AREMOVAL

OPERATION FOR REMOVAL OF PART CONCERNED

a Remove the centre trim.

a Remove the side trims.

a Remove:

- the bolts (1) ,

- the tailgate trim.

REFITTING


a


a Refit:

- the tailgate trim,

- the side trims,

- the centre trim.

137385

137387

137391

Note:

Always check the condition of the clips andreplace them if necessary.

73A-2

NON-SIDE OPENING ELEMENTS TRIMLuggage compartment lid trim: Removal - Refitting

L38

73A

REMOVAL

REMOVAL OPERATION

a Unclip the clips (1) using the tool (Car. 1363).

a Unclip the clips (2) of the side trims using the tool(Car. 1363).

a Remove the side trims.

a Remove the boot lid trim.

REFITTING


a Always check the condition of the clips and replacethem if necessary.





143945

EQUIPMENT LEVEL EA3

144142

75A-1

FRONT SEAT FRAMES AND MECHANISMSFront seat base frame: Removal - Refitting

EXPORT EQUIPMENT LEVEL ADDITIONAL

75A

REMOVAL


a Disconnect the battery (see Battery: Removal - Re-fitting) .

a Remove:

- the front headrest (see 79A, Seat accessories,Front headrest: Removal - Refitting, page 79A-1) ,

- the front seat (see 75A, Front seat frames andmechanisms, Complete front seat: Removal -Refitting, page 75A-13) ,

- the front seat lower casings (see 77A, Front seattrim, Front seat lower casing: Removal - Refit-ting, page 77A-12) ,

- the front seat base trim (see 77A, Front seat trim,Front seat base trim: Removal - Refitting, page77A-1) ,

- the front seat belt buckle stalk (see Front seat beltbuckle: Removal - Refitting) (88C, Airbag andpretensioners),

- the side airbag (see Front (chest-level) side air-bag: Removal - Refitting) ,

- the front seat lap belt pretensioner (see Front seatlap belt pretensioner: Removal - Refitting)

- the front seat runners (see 75A, Front seat framesand mechanisms, Front seat runner: Removal -Refitting, page 75A-4) .

- the electrical wiring,

- the front seat base pad.

a Remove the front seat height adjustment mecha-nism (see Front seat height adjuster: Removal -Refitting) .


a Remove:

- the bolts (1) from the front seat « seatback - seatbase » frame,

- the front seat base frame.

REFITTING


a parts always to be replaced: Front seatbackframe mounting on front seat base frame (70,08,02,09).



a Torque tighten the new bolts for the « seatback -seat base » frame on the front seat (40 N.m).


Tightening torquesm

new bolts for the« seatback - seatbase » frame on thefront seat

40 N.m

Note:

It is prohibited to carry out any welding operation onthe frames of the seat and bench seat.

FRONT SEAT TYPE 02 or FRONT SEAT TYPE 04or FRONT SEAT TYPE 05 or FRONT SEAT TYPE06

138035

75A-2

FRONT SEAT FRAMES AND MECHANISMSFront seatback frame: Removal - Refitting


75A

REMOVAL



a Remove:

- the front seat headrest (see 79A, Seat accesso-ries, Front headrest: Removal - Refitting, page79A-1) ,

- the compete front seat (see 75A , Front seatframes and mechanisms, Complete front seat:Removal - Refitting, page 75A-13) ,

- the front seat lower casings (see 77A, Front seattrim, Front seat lower casing: Removal - Refit-ting, page 77A-12) .

a Remove the front seat height adjustment control(see 75A, Front seat frames and mechanisms,Front seat height adjuster control: Removal - Re-fitting, page 75A-6) .

a Remove the front seat lumbar adjustment control(see 75A, Front seat frames and mechanisms,Front seat lumbar adjustment control: Removal -Refitting, page 75A-11) .

a Remove:

- the front seat headrest guides (see 79A, Seat ac-cessories, Front seat headrest guide: Removal- Refitting, page 79A-4) ,

- the front seatback « foam - cover » assembly (see77A, Front seat trim, Front seatback trim: Re-moval - Refitting, page 77A-4) ,

- the front side (chest-level) airbag (see Front(chest-level) side airbag: Removal - Refitting)(88C, Airbags and pretensioners).

a Remove the front seat lumbar adjustment mecha-nism (see 75A, Front seat frames and mecha-nisms, Front seat lumbar adjustment: Removal -Refitting, page 75A-9) .

a Remove the lumbar pad of the front seatback.

Tightening torquesm

new bolts for the« seatback - seatbase » frame on thefront seat

40 N.m

Note:

It is prohibited to carry out any welding operation onthe frames of the seat and bench seat.

Note:

Depending on the method of sale defined by theParts Department, adaptations can be made to theseat frames.

In this case, it is permitted to eliminate certain com-ponents (supports, wires, brackets, inserts, etc)depending on vehicle type.


FRONT ARMREST, and FRONT SEAT TYPE 05 orFRONT SEAT TYPE 06

FRONT ARMREST, and FRONT SEAT TYPE 05 orFRONT SEAT TYPE 06

75A-3

FRONT SEAT FRAMES AND MECHANISMSFront seatback frame: Removal - Refitting


75AII - REMOVAL OPERATION

a Remove:

- the bolts (1) from the front seat « seatback - seatbase » frame,

- the front seatback frame.

REFITTING


a parts always to be replaced: Front seatbackframe mounting on front seat base frame (70,08,02,09).


a Refit the front seatback frame.

a Torque tighten the new bolts for the « seatback -seat base » frame on the front seat (40 N.m).




138050

75A-4

FRONT SEAT FRAMES AND MECHANISMSFront seat runner: Removal - Refitting


75A

REMOVAL


a

a Lock the airbag computer using the Diagnostic tool(see Fault finding - Replacement of components)(88C, Airbag and pretensioners).

a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery). .

a Remove the front headrest (see 79A, Seat acces-sories, Front headrest: Removal - Refitting, page79A-1) (79A, Front seat accessories).

a Remove:

- the compete front seat (see 75A , Front seatframes and mechanisms, Complete front seat:Removal - Refitting, page 75A-13) ,

- the front seat lower casings (see 77A, Front seattrim, Front seat lower casing: Removal - Refit-ting, page 77A-12) ,

- the front seat lap belt pretensioner (see Preten-sioner: Removal - Refitting) (88C, Front seat lapbelt pretensioner).


a Remove:

- the nuts of the front seat "seat base - runner"frame,

- the front seat runners.

REFITTING


a parts always to be replaced: Front seat runnermounting on front seat frame (70,08,04,27)

Equipment required

Diagnostic tool

Tightening torquesm

new nuts of the frontseat "seat base - run-ner" frame

21 N.m

IMPORTANT

To avoid a fault with or even triggering of pyro-technic components (airbags or pretensioners),check the airbag computer using the diagnostictool.

144148

144149

75A-5

FRONT SEAT FRAMES AND MECHANISMSFront seat runner: Removal - Refitting


75AII - REFITTING OPERATION

a Refit the front seat runners.

a Finger tighten all the attachments.

a Position the runners so that there is a centre-to-cen-tre distance of 428.5 mm between the two rearmountings.

a Torque tighten the new nuts of the front seat "seatbase - runner" frame (21 N.m).




139548

75A-6

FRONT SEAT FRAMES AND MECHANISMSFront seat height adjuster control: Removal - Refitting

FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05, andEXPORT EQUIPMENT LEVEL ADDITIONAL

75A

REMOVAL


a Move aside the seat belt protector (1) .

a Unclip the front seat belt using a flat-blade screw-driver at (2) .

a Remove the front seatback angle control (see 75A,Front seat frames and mechanisms, Front seatbackrest tilt control: Removal - Refitting, page75A-12) .

Tightening torquesm

bolts of the front seatheight adjustment con-trol

6 N.m

143963

143962

75A-7

FRONT SEAT FRAMES AND MECHANISMSFront seat height adjuster control: Removal - Refitting


75A

a Remove:

- the bolt (3) ,

- the bolt (4) .


a Move aside the exterior casing of the front seat base(5) so that the bolts (6) can be accessed.

a Remove:

- the bolts (6) of the front seat height adjustmentcontrol,

- the front seat height adjustment control (7) .

REFITTING


a Torque tighten the bolts of the front seat heightadjustment control (6 N.m).


143775

143774

143773

75A-8

FRONT SEAT FRAMES AND MECHANISMSFront seat height adjustment: Removal - Refitting


75A

a

a Whenever replacing a front seat height adjustmentmechanism, refer to the replacement procedure forthe front seat base frame.

138033

Note:

The torsion bar is used again on the front seatheight adjustment mechanism.

The front seat height adjustment mechanismcannot be removed.

The Parts Department supplies the front seatframe assembled with the front seat heightadjustment mechanism.

75A-9

FRONT SEAT FRAMES AND MECHANISMSFront seat lumbar adjustment: Removal - Refitting

FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06, and EXPORT EQUIPMENT LEVEL ADDITIONAL

75AREMOVAL



a Remove:

- the front seat headrest (see 79A, Seat accesso-ries, Front headrest: Removal - Refitting, page79A-1) ,


- the front seat base casings (see 77A, Front seattrim, Front seat lower casing: Removal - Refit-ting, page 77A-12) ,

- the front seat headrest guides (see 79A, Seat ac-cessories, Front seat headrest guide: Removal- Refitting, page 79A-4) ,

- the front seatback "foam - cover" assembly (see77A, Front seat trim, Front seatback trim: Re-moval - Refitting, page 77A-4) .


a Remove the bolt (1) from the front seat lumbar ad-justment mechanism.

a Unclip the lumbar pad of the front seat at (2) .

a Remove the « lumbar adjustment mechanism - lum-bar pad » assembly.

138051

Note:

For this operation, the lumbar pad must be loose.

144381

Note:

The Parts Department supplies the lumbaradjustment mechanism assembled with the lum-bar pad.

75A-10

FRONT SEAT FRAMES AND MECHANISMSFront seat lumbar adjustment: Removal - Refitting


75AREFITTING

a



138053

Note:

The lumbar pad springs on the front seatbackframe are positioned with the hook facingtowards the rear.

75A-11

FRONT SEAT FRAMES AND MECHANISMSFront seat lumbar adjustment control: Removal - Refitting


75AREMOVAL

REMOVAL OPERATION

a Unclip the front seat lumbar adjustment control (1) .

REFITTING

a Clip on the lumbar adjustment control.


144145

Note:

The vertical position (upwards) of the control cor-responds to a relaxed pad.

75A-12

FRONT SEAT FRAMES AND MECHANISMSFront seat backrest tilt control: Removal - Refitting


75A

REMOVAL

REMOVAL OPERATION

a Unclip the front seatback angle control at (1) usingthe tool (Car. 1363).

REFITTING


a Clip on the front seatback angle control.





143771

75A-13

FRONT SEAT FRAMES AND MECHANISMSComplete front seat: Removal - Refitting


75A

REMOVAL


a Adjust:

- the steering wheel to the top position and push it in,

- the front seatback angle to the vertical position,

- the height of the front seat base to the low position.

a Disconnect the battery (see Battery: Removal - Re-fitting) .

a Remove the front seat headrest (see 79A, Seat ac-cessories, Front headrest: Removal - Refitting,page 79A-1) .

a Protect the front door sill lining with masking tape.


a Move the front seat back.

a Remove the front seat bolts on the body (1) .

a Move the front seat forwards.

a Remove the front seat bolts on the body (2) .

Tightening torquesm

new front seat bolts 35 N.m

139314

139409

75A-14



75A

a Move aside the seat belt protector (3) .

a Unclip the front seat belt using a flat-blade screw-driver at (4) .

a Tilt the front seat backwards.

a Disconnect the connector from the front seat wiring.

a Unclip the mounting from the front seat wiring.

a Remove the front seat.

REFITTING


a parts always to be replaced: Front seat mount-ing on body (70,06,02,01)


a Refit the front seat.

a Connect the front seat wiring connector.

a Clip on the front seat wiring mounting.

a Connect the battery (see Battery: Removal - Refit-ting) .

143963

143962

139317

Note:

Hold the wiring mounting to avoid breaking itsindexing guide (5) , when disconnecting the con-nector from the front seat wiring.

75A-15



75ADriver's side

a Tighten in the order indicated (1) , (2) , (3) , (4) .

Passenger side

a Tighten in the order indicated (1) , (2) , (3) , (4) .

a Torque tighten the new front seat bolts (35 N.m).


a Refit the front headrest (see 79A, Seat accesso-ries, Front headrest: Removal - Refitting, page79A-1)

a Clip the front seat belt into the lap belt pretensioner.


a Adjust the following to their original positions:

- the height and the depth of the steering wheel,

- the front seatback angle,

- the front seat base height.

a Remove the masking tape from the front door sill lin-ing.

139316

139316

76A-1

REAR SEAT FRAMES AND MECHANISMSRear bench seatback: Removal - Refitting


76A

REMOVAL


a Remove the rear bench seat base (see 76A, Rearseat frames and mechanisms, Rear bench seat-back: Removal - Refitting, page 76A-1) .


a Remove the rear seat belt buckle bolt (1) .

a Remove the bolt (2) from the 1/3 rear bench seat-back.

a Remove the bolts (3) from the 2/3 rear bench seat-back.

Tightening torquesm

bolts of the rear benchseatback

21 N.m

rear seat belt buckle bolt 21 N.m


144118

144120

144119

76A-2



76A

a Remove the bolt (4) from the rear bench seatbackon each side. a Release the 1/3 rear bench seatback from the anti-

release pins at (5) .

a Remove the 1/3 rear bench seatback at (6) .

a Release the 2/3 rear bench seatback from the anti-release pins at (7) .

a Remove the 2/3 rear bench seatback at (8) .


144119


142704

144386

76A-3



76A

a Release the rear bench seatback from the anti-re-lease pins at (9) on each side.

a Remove the rear bench seatback at (10) on eachside.

REFITTING


a parts always to be replaced: Rear seat belt buck-le bolt (31,02,01,51).



a Torque tighten:

- the bolts of the rear bench seatback (21 N.m),

- the rear seat belt buckle bolt (21 N.m).


144356

76A-4

REAR SEAT FRAMES AND MECHANISMSRear bench seat base: Removal - Refitting


76AREMOVAL


a Tilt the single unit rear bench seat base.

a Tilt the 1/3 rear bench seat base.

a Tilt the 2/3 rear bench seat base.


a Unclip the single unit rear bench seat base.


136700


143944

143952


136702

76A-5

REAR SEAT FRAMES AND MECHANISMSRear bench seat base: Removal - Refitting


76A

a Unclip the 1/3 rear bench seat base.

a Unclip the 2/3 rear bench seat base.

a Remove the rear bench seat base.

REFITTING




a Pull down the rear bench seat base.1-2/3 REAR BENCH SEAT + ARMREST + N/RSEATBACK

136709

136715

76A-6

REAR SEAT FRAMES AND MECHANISMSRear bench seat mechanism: Removal - Refitting

FOLDING REAR BENCH SEAT or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK

76A

REMOVAL


a Remove:

- the rear bench seat headrests (see 79A, Seat ac-cessories, Rear bench seat headrest: Removal- Refitting, page 79A-10) ,

- the rear bench seat headrest guides (see 79A,Seat accessories, Rear bench seat headrestguide: Removal - Refitting, page 79A-8) .

a Remove the rear bench seatback (see 76A, Rearseat frames and mechanisms, Rear bench seat-back: Removal - Refitting, page 76A-1) .

a Remove the cover from the rear bench seatback(see Single unit rear bench seatback trim: Re-moval - Refitting) .

a Remove the rear bench seatback (see 76A, Rearseat frames and mechanisms, Rear bench seat-back: Removal - Refitting, page 76A-1) .

a Remove:

- the rear centre armrest (see 79A, Seat accesso-ries, Rear centre armrest: Removal - Refitting,page 79A-7) ,

- the cover of the rear bench seatback (see 78A,Rear seat trim, 1/3 and 2/3 rear bench seatbacktrim: Removal - Refitting, page 78A-1) .


a Remove:

- the bolts (1) of the rear bench seatback lockingmechanism,

- the locking mechanism of the rear bench seatback(2) .

REFITTING

a Proceed in reverse order to removal.

a Torque tighten the bolts of the rear bench seat-back locking mechanism (18 N.m).


Tightening torquesm

bolts of the rear benchseatback locking mech-anism

18 N.m





137427

77A-1

FRONT SEAT TRIMFront seat base trim: Removal - Refitting


77A

REMOVAL


a Lock the airbag computer using the Diagnostic tool(see Airbag and pretensioners: Precautions forthe repair) (see 88C, Airbags and Pretensioners).


a Remove:


- the front seatback angle control (see 75A, Frontseat frames and mechanisms, Front seat back-rest tilt control: Removal - Refitting, page 75A-12) ,

- the front seat base casing (see 77A, Front seattrim, Front seat lower casing: Removal - Refit-ting, page 77A-12) ,

- the front seat height adjustment control (see 75A,Front seat frames and mechanisms, Front seatheight adjuster control: Removal - Refitting,page 75A-6) .

a Remove the elastic securing straps (1) from theseatback cover.


Car. 1521 Clip crimping pliers.

Equipment required

Diagnostic tool

IMPORTANTTo prevent any accidental triggering whilst workingon or near a passive safety element, apply the pro-cedure for deactivating the safety systems (see Air-bags and pretensioners: Precautions for the repair)

IMPORTANT

Never handle the pyrotechnic systems (pretension-ers or airbags) near to a source of heat or nakedflame - they may be triggered.

CLOTH 03 or CLOTH 04 or CLOTH 05 or CLOTH06 or CLOTH 07

143958

77A-2




a Remove:

- the elastic retaining strap (2) on the seatback cov-er,

- the front retaining sections (3) of the front seatbase cover,

- the side retaining sections (4) of the front seat basecover,

- the "cover - foam" assembly of the front seat base.

a Cut the clips on the seat trim (5) .

a Remove the front seat base cover.

CLOTH 03 or CLOTH 04 or CLOTH 05 or CLOTH06 or CLOTH 07

143959

143960

143961

77A-3



77AREFITTING


a parts always to be replaced: Seat trim clip (70,10,02,19)


a Refit:

- the front seat base cover,

- the new seat trim clips using the tool (Car. 1521) onthe centre section,

- the clips of the seat trim using the tool (Car. 1521)on the side sections.

a Refit the "cover - foam" assembly of the front seatbase.


Note:

To avoid any risk of damaging the seat trims andmechanisms, remove any metal residues of theseat trim clips.

77A-4

FRONT SEAT TRIMFront seatback trim: Removal - Refitting

CLOTH 06 or CLOTH 07, and EXPORT EQUIPMENT LEVEL ADDITIONAL

77A

REMOVAL




a Remove:


- the front seat headrest guides (see 79A, Seat ac-cessories, Front seat headrest guide: Removal- Refitting, page 79A-4) .




a Remove the elastic securing straps (1) of the frontseatback cover.



Equipment required

Diagnostic tool

IMPORTANTTo avoid a fault with or even triggering of pyrotech-nic components (airbags or pretensioners), checkthe airbag computer using the diagnostic tool.

IMPORTANT



FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06

143958

77A-5



77A

a Unclip the lower retaining section (2) of the frontseatback cover.

144150

77A-6



77A

a Gradually cut the clips on the seat trim (3) .

a Remove the front seatback cover on the centre vel-cro strips.

144151

144152

144153

144154

WARNING

To avoid any risk of damaging the foam, separatethe cover from the foam by holding the velcrostr ips.

77A-7



77A

a Unlock the retaining section pin of the front seat(chest-level) side airbag concentrator.

a Remove the retaining section pin (4) from the frontseat (chest-level) side airbag concentrator.

a Detach the retaining section of the front seat side(chest-level) airbag concentrator at (5) by sliding it.

a Separate the seatback cover from the front seatfoam.

REFITTING


a parts always to be replaced: Seat trim clip (70,10,02,19).


a Check that the velcro strips are properly fastened onthe foam.

a Crimp the new seat trim clips onto the lumbar padusing the tool (Car. 1521).


Note:


FRONT SIDE AIRBAG or FRONT SIDE + CUR-TAIN AIRBAG

141590

141591

77A-8


CLOTH 03 or CLOTH 04 or CLOTH 05, and EXPORT EQUIPMENT LEVEL ADDITIONAL

77A

REMOVAL

I - REMOVAL OPERATION



a Remove:


- the front seat headrest guides (see 79A, Seat ac-cessories, Front seat headrest guide: Removal- Refitting, page 79A-4) .




a Remove the elastic retaining straps (1) of the frontseatback cover from the front seat base frame.



Equipment required

Diagnostic tool

IMPORTANTTo avoid a fault with or even triggering of pyrotech-nic components (airbags or pretensioners), checkthe airbag computer using the diagnostic tool.

IMPORTANT



FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06

143958

77A-9



77A

a Unclip the lower retaining section (2) of the frontseatback cover.

144150

77A-10



77A

a Gradually cut the clips on the seat trim (3) .

144277

144279

144280

WARNING


77A-11



77A

a Unlock the retaining section pin of the front seat(chest-level) side airbag concentrator.

a Remove the retaining section pin (4) from the frontseat (chest-level) side airbag concentrator.

a Detach the retaining section of the front seat side(chest-level) airbag at (5) by sliding it.

a Remove the front seatback cover.

REFITTING


a parts always to be replaced: Seat trim clip (70,10,02,19).



a Crimp the new seat trim clips onto the lumbar padusing the tool (Car. 1521).

FRONT SIDE AIRBAG or FRONT SIDE + CUR-TAIN AIRBAG

144278

141591

77A-12

FRONT SEAT TRIMFront seat lower casing: Removal - Refitting


77A

REMOVAL




a Remove the front seat (see 75A, Front seat framesand mechanisms, Complete front seat: Removal- Refitting, page 75A-13) .

a Remove the elastic straps (1) from the front seat-back cover.


1 - Front seat base interior casing

a Unclip the front seat base interior casing (2) .

a

Equipment required

Diagnostic tool

137996

138045

143772

Note:

Replace the clip if deteriorated.

77A-13

FRONT SEAT TRIMFront seat lower casing: Removal - Refitting


77A2 - Front seat base exterior casing

a Remove:

- the bolts (3) and (4) from the front seat base exteri-or casing,

- the front seatback angle control (see 75A, Frontseat frames and mechanisms, Front seat back-rest tilt control: Removal - Refitting, page 75A-12) ,

- the front seat height adjustment control (see 75A,Front seat frames and mechanisms, Front seatheight adjuster control: Removal - Refitting,page 75A-6) .

a Unclip the front seat base exterior casing.

a Disconnect the connector (5) from the front seatheated pad.

a Unclip the clip from the wiring of the front seat heat-ed pad (6) .

REFITTING

REFITTING OPERATION




143775

143774

FRONT SEAT WITH HEATING

138048

78A-1

REAR SEAT TRIM1/3 and 2/3 rear bench seatback trim: Removal - Refitting

1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL

78A

REMOVAL


a Remove:

- the rear bench seat bases (see 76A, Rear seatframes and mechanisms, Rear bench seatbase: Removal - Refitting, page 76A-4) ,

- the rear bench seatbacks (see 76A, Rear seatframes and mechanisms, Rear bench seatback:Removal - Refitting, page 76A-1) ,

- the rear headrests (see 79A, Seat accessories,Rear bench seat headrest: Removal - Refitting,page 79A-10) .

a Unclip the trims from the unlocking control of therear bench seatback using the tool (Car. 1363).



Car. 1558 Pliers for zip fasteners.

Tightening torquesm

bolts of the rear benchseat supports

35 N.m

137435

142782

78A-2



78A1 - 2/3 rear bench seatback cover

a Remove:

- the bolt (1) ,

- the trim of the rear centre seat belt strap guide,

- the rear central armrest (see 79A, Seat accesso-ries, Rear centre armrest: Removal - Refitting,page 79A-7) .

a Remove:

- the bolts (2) ,

- the 2/3 rear bench seat supports.

2 - 1/3 rear bench seatback cover

a Remove:

- the bolts (3) ,

- the 1/3 rear bench seat supports.

137422

142785

142808

78A-3





a Extract the zip fasteners (4) .

a Open the zip fasteners.

a Remove clip (5) .

a Lift up the foam of the 2/3 rear bench seatback.


a Remove:

- the 2/3 rear bench seat headrest guides (see 79A,Seat accessories, Rear bench seat headrestguide: Removal - Refitting, page 79A-8) ,

- the "cover - foam" assembly of the 2/3 rear benchseatback.

144187

142788

142789

78A-4



78A

a Separate the cover from the 2/3 rear bench seat-back foam.

a Remove the cover of the 2/3 rear bench seatback.


a Extract the zip fasteners (7) .

a Open the zip fasteners.

a Remove:

- the clip (8) ,

- the rear bench seat headrest guides (see 79A,Seat accessories, Rear bench seat headrestguide: Removal - Refitting, page 79A-8) ,

- the "cover - foam" assembly of the 1/3 rear benchseatback.

142787

WARNING

To avoid any risk of damaging the foam, separatethe cover from the foam by holding the velcrostrips.

137424

78A-5



78A

a Separate the cover from the 1/3 rear bench seat-back foam.

a Remove the cover of the 1/3 rear bench seatback.

REFITTING



142786

WARNING


142781

142779

WARNING

To avoid any risk of the cover detaching or anyfolds in the cover, check that the velcro strips aresecure on the foam. If the velcro strip tears,replace the foam.

78A-6



78A

a Position the cover of the rear bench seatback on thefoam, starting with the side velcro strips.

a Align the ends of the velcro strips with the marks (9) .


a Refit the cover of the rear bench seatback on thefoam.

a Check that there are no folds in the cover.

a Refit:

- the « cover - foam » assembly of the rear benchseatback,

- the rear bench seat headrest guides (see 79A,Seat accessories, Rear bench seat headrestguide: Removal - Refitting, page 79A-8) .

2/3 rear bench seatback cover


a Refit the clips (5) .

a Close the zip fasteners using the tool (Car. 1558).

a Fit the zip fasteners (4) .

1/3 rear bench seatback cover

a Refit the clip (8) .

a Close the zip fasteners using the tool (Car. 1558).

a Fit the zip fasteners (7) .



a Refit:

- the rear centre armrest (see 79A, Seat accesso-ries, Rear centre armrest: Removal - Refitting,page 79A-7) ,

- the 2/3 rear bench seat supports,

- the bolts (2) ,

- the trim of the rear centre seat belt strap guide,

- the bolt (1) .


a Refit:

- the 1/3 rear bench seat supports,

- the bolts (3) .

a Torque tighten the bolts of the rear bench seatsupports (35 N.m).

a Clip on the trims of the unlocking control for the rearbench seatback.

a Refit:

- the rear headrests (see 79A, Seat accessories,Rear bench seat headrest: Removal - Refitting,page 79A-10) ,

- the rear bench seatbacks (see 76A, Rear seatframes and mechanisms, Rear bench seatback:Removal - Refitting, page 76A-1) ,

- the rear bench seat bases (see 76A, Rear seatframes and mechanisms, Rear bench seatbase: Removal - Refitting, page 76A-4) .

142780

Note:

The markings on the foam are a guide for posi-tioning the velcro strips.

78A-7

REAR SEAT TRIMRear bench seat base trim: Removal - Refitting


78A

REMOVAL


a Remove the rear bench seat base (see 76A, Rearseat frames and mechanisms, Rear bench seatbase: Removal - Refitting, page 76A-4) .


1/3 seat

2/3 seat

a Cut the clips (1) .

a Remove:

- the cover retaining sections (2) ,

- the « cover - foam » assembly of the rear benchseat base.



144382

144383

78A-8



78A

a Separate the cover from the rear bench seat basefoam.

a Remove the cover of the rear bench seat base.

REFITTING


a parts always to be replaced: Seat trim clip (70,10,02,19)

Incorrect

Correct


137412

WARNING


142781

142779

WARNING

To avoid any risk of the cover detaching or anyfolds in the cover, check that the velcro strips aresecure on the foam. If the velcro strip tears,replace the foam.

78A-9



78A

a Position the cover of the rear bench seat base on thefoam, starting with the side velcro strips.

a Align the ends of the velcro strips with the marks (4) .


a Refit the cover (3) of the rear bench seat base on thefoam.


a Refit:

- the « cover - foam » assembly of the rear benchseat base,

- the retaining sections (2) of the rear bench seatbase cover,

- the clips (1) using the tool (Car. 1521).



a Refit the rear bench seat base (see 76A, Rear seatframes and mechanisms, Rear bench seat base:Removal - Refitting, page 76A-4) .

142780

Note:

The markings on the foam are a guide for posi-tioning the velcro strips.

79A-1

SEAT ACCESSORIESFront headrest: Removal - Refitting


79AREMOVAL


a Tilt the seatback backwards.


a

a Press the unlocking button on each headrest guide.

Note:

The front seat headrest has an integrated con-trol.

139290

139291

Note:

Depending on the type of unlocking button, thisoperation is performed manually or using a flat-blade screwdriver.

79A-2



79A

a Remove the front seat headrest.

139292

79A-3



79AREFITTING

REFITTING OPERATION FOR PART CONCERNED

Unaligned headrest rods

Headrest rods aligned

a Bring the rods out of the front seat headrest as far aspossible by pulling upwards.

a Insert the rods of the front seat headrest in the head-rest guides.

a Push the front seat headrest until it locks into placewith the locking notches then adjust the front seatheadrest to the low position.

FRONT HEADRESTS 0 or FRONT HEADRESTS 0

142683

142684

IMPORTANTTo avoid any risk of incorrectly positioning therods of the front seat headrest, align the rodsbefore inserting them in the headrest guides.

IMPORTANTTo prevent the headrest coming away from theguide during a collision, check that headrestguide locking system is functioning correctly.

79A-4

SEAT ACCESSORIESFront seat headrest guide: Removal - Refitting


79AREMOVAL


a Remove the front seat headrest (see 79A, Seat ac-cessories, Front headrest: Removal - Refitting,page 79A-1) .

Note:

The headrest guides can be removed withoutremoving the front seatback cover.

79A-5

SEAT ACCESSORIESFront seat headrest guide: Removal - Refitting


79AII - OPERATION FOR REMOVAL OF PART CONCERNED

a Slightly detach the "foam - cover" assembly of theseatback near the headrest guides to reveal thelocking clips of the front seat headrest guides.

a Unclip the front seat headrest guides by pressing thelocking clips using a flat-blade screwdriver.

a Remove the front seat headrest guides.

REFITTING


a Refit the headrest guides fully into the front seatbackframe.

a Check that the headrest guides are secure in thefront seatback frame.


a Refit the front seat headrest (see 79A, Seat acces-sories, Front headrest: Removal - Refitting, page79A-1) .


139289

141582

Note:

The locking clips of the front seat headrestguides are all on the same side.

Note:

To prevent the headrest guides from being mixedup, each headrest guide has a specific indexingdevice.

IMPORTANT

To prevent the headrest coming away from theguide during a collision, check that headrestguide locking system is functioning correctly.

79A-6

SEAT ACCESSORIESFront armrest: Removal - Refitting

FRONT ARMREST, and EXPORT EQUIPMENT LEVEL ADDITIONAL

79AREMOVAL


a Unclip the rear panel of the centre console (seeCentre console: Removal - Refitting) (57A, Interi-or equipment).

a Remove the rear air distribution duct on the rear sec-tion of the centre console (see Rear air distributionduct: Removal - Refitting) (61A, Heating system).


a Remove:

- the front armrest mounting bolts (1) ,

- the front armrest.

REFITTING



144144

79A-7

SEAT ACCESSORIESRear centre armrest: Removal - Refitting


79AREMOVAL


a Tilt the 1/3 rear bench seat (1) .


a Remove:

- the bolt (2) ,

- the rear central armrest.

REFITTING


a Refit:

- the rear central armrest,

- the bolt (2) .


a Position the 1/3 rear bench seat (1) .

134165

134166

79A-8

SEAT ACCESSORIESRear bench seat headrest guide: Removal - Refitting


79AREMOVAL


a Remove the rear bench seat headrests (see 79A,Seat accessories, Rear bench seat headrest: Re-moval - Refitting, page 79A-10) .

a Remove:

- the rear bench seat base (see Single unit rearbench seat base: Removal - Refitting) ,

- the rear bench seatback (see Single unit rearbench seatback: Removal - Refitting) ,

- the rear bench seatback cover partially (see Singleunit rear bench seatback trim: Removal - Refit-ting) .

a Remove:

- the rear bench seat base (see 76A, Rear seatframes and mechanisms, Rear bench seatbase: Removal - Refitting, page 76A-4) ,

- the rear bench seatback (see 76A , Rear seatframes and mechanisms, Rear bench seatback:Removal - Refitting, page 76A-1) ,

- the central armrest of the rear bench seat (see79A, Seat accessories, Rear centre armrest:Removal - Refitting, page 79A-7) ,

- the rear bench seatback cover partially (see 78A,Rear seat trim, 1/3 and 2/3 rear bench seatbacktrim: Removal - Refitting, page 78A-1) .


a Unclip the rear bench seat headrest guides.

a Remove the rear bench seat headrest guides.

REFITTING


a Refit the rear bench seat headrest guides fully intothe rear seat frame.

a Check that the rear bench seat headrest guides aresecure on the rear seat frame.



137431

141490

79A-9

SEAT ACCESSORIESRear bench seat headrest guide: Removal - Refitting


79AII - FINAL OPERATION

a Refit:

- the cover of the rear bench seatback (see 78A,Rear seat trim, 1/3 and 2/3 rear bench seatbacktrim: Removal - Refitting, page 78A-1) ,

- the central armrest of the rear bench seat (see79A, Seat accessories, Rear centre armrest:Removal - Refitting, page 79A-7) ,

- the rear bench seatback (see 76A , Rear seatframes and mechanisms, Rear bench seatback:Removal - Refitting, page 76A-1) ,

- the rear bench seat base (see 76A, Rear seatframes and mechanisms, Rear bench seatbase: Removal - Refitting, page 76A-4) .

a Refit:

- the cover of the rear bench seatback (see Singleunit rear bench seatback trim: Removal - Refit-ting) ,

- the rear bench seatback (see Single unit rearbench seatback: Removal - Refitting) ,

- the rear bench seat base (see Single unit rearbench seat base: Removal - Refitting) .

a Refit the rear bench seat headrests (see 79A, Seataccessories, Rear bench seat headrest: Remov-al - Refitting, page 79A-10) .



IMPORTANT


79A-10

SEAT ACCESSORIESRear bench seat headrest: Removal - Refitting


79A

REMOVAL

OPERATION FOR REMOVAL OF PART CONCERNED

a Press the unlocking buttons on each rear bench seatheadrest guide at (1) .

a Remove the rear bench seat headrest.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Refit the rear bench seat headrest into the guides tothe safety notch position.

a Press the unlocking button of the headrest guide forthe left-hand rear bench seat.


a Adjust the rear bench seat headrest to the low posi-tion.

a

Note:

Depending on the type of unlocking button, thisoperation is performed manually or using a flat-blade screwdriver.

137420

IMPORTANT


7 trim and upholstery - cars.usoft.czcars.usoft.cz/soubory/manualy/fluence7.pdffluence - megane...

Documents