6.1 flanges asme b16 - forxarind.com flanges asme b16.5.pdf · and lapped flanges. this dimension...
TRANSCRIPT
Q u a l i t y a t C o r e
1
Types• Weldneck • SORF • BLRF • Slipon • High Hub • Socket Weld • Flat Face
• Threaded • Ring Type Joint • Groove & Tongue • Expander • Spectacle
Standards • ASME B16.5 • ASME B16.36 • ASME B16.47 • API 6A
• EN 1092-1 • EN 1098 • BS 10 • B2291 • JIS B2220.
1/2” - 24”Size
Class 150 to Class 2500 • PN 6 - PN 100 • Table D, E, F.Pressure Rating
Features
• Heat code traceability • 100% material annealed & passivated • High quality steel finish • Three chambers cleaning system ( Surface preparation, Ultrasonic Degreasing, Hot Dry Air.)
Bellow Seal
Zero Emission
Flanges
E.mail : @forxarind.com web : www.forxarind.com. sales
Q u a l i t y a t C o r e
2
Bellow Seal
Zero Emission
NOTES: (For 150# & 300# Class)(1) This dimension is for large end of hub, which may be straight or tapered. Taper shall not exceed 7 deg on threaded, slip-on, socket-welding, and lapped flanges. This dimension is defined as the diameter at the intersection between the hub taper and back face of the flange.(2) The minimum thickness of these loose flanges, in sizes NPS 3 Ω and smaller, is slightly greater than the thickness of flanges on fittings, which are reinforced by being cast integral with the body of the fitting.(3) For Class 300 these flanges may be supplied with a flat face. The flat face may be either the full t (4) Dimensions in Column 15 correspond to the inside diameters of pipe as given in ASME B36.10M for standard wall pipe. Thickness of standard wall is the same as Schedules.(5) To be specified by the Purchaser.(6)
f dimension of thickness plus 2 mm or the tf dimension thickness without the raised face height.
2.0 mm (0.06 in.) raised face for Class 150 and 300 raised face flanges
NB NPS O XS/O & S/W W/N L/J
Y Y YS/O & S/W L/J
B B F
152025324050658090
100125150200250300350400450500600
1/23/41
1 1/41 1/2
22 1/2
33 1/2
4568
10121416182024
90 100 110 115 125 150 180 190 215 230 255 280 345 405 485 535 595635 700 815
9.6 11.2 12.7 14.3 15.9 17.5 20.7 22.3 22.3 22.3 22.3 23.9 27.0 28.6 30.2 33.4 35.0 38.1 41.3 46.1
11.2 12.7 14.3 15.9 17.5 19.1 22.3 23.9 23.9 23.9 23.9 25.4 28.6 30.2 31.8 35.0 36.6 39.7 42.9 47.7
30 38 49 59 65 78 90
108 122 135 164 192 246 305 365 400 457 505 559 663
14 14 16 19 21 24 27 29 30 32 35 38 43 48 54 56 62 67 71 81
46 51 54 56 60 62 68 68 70 75 87 87
100 100 113 125 125 138 143 151
16 16 17 21 22 25 29 30 32 33 36 40 44 49 56 79 87 97 103 111
22.2 27.7 34.5 43.2 49.5 61.9 74.6 90.7
103.4 116.1 143.8 170.7 221.5 276.2 327.0 359.2 410.5 461.8 513.1 616.0
15.8 20.9 26.6 35.1 40.9 52.5 62.7 77.9 90.1
102.3 128.2 154.1 202.7 254.6 304.8 Note (5) Note (5) Note (5) Note (5) Note (5)
22.9 28.2 34.9 43.7 50.0 62.5 75.4 91.4
104.1 116.8 144.4 171.4 222.2 277.4 328.2 360.2 411.2 462.3 514.4 616.0
1011131416171921. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
W d
60.369.979.488.998.4
120.7139.7152.4177.8190.5215.9241.3298.5362.0 431.8 476.3 539.8 577.9 635.0 749.3
4444444488888
121212 16 16 20 20
B
5/85/85/85/85/83/43/43/43/43/47/87/87/811
1 1/81 1/81 1/41 1/41 3/8
R n tf tf Ah
21.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0610.0
T
1616172122252930323336404449565764687383
N - 2
NB NPS O XS/O & S/W W/N L/J
Y Y YL/JB F
152025324050658090
100125150200250300350400450500600
1/23/41
1 1/41 1/2
22 1/2
33 1/2
4568
10121416182024
22.2 27.7 34.5 43.2 49.5 61.9 74.6 90.7
103.4 116.1 143.8 170.7 221.5 276.2 327.0 359.2 410.5 461.8 513.1 616.0
15.8 20.9 26.6 35.1 40.9 52.5 62.7 77.9 90.1
102.3 128.2 154.1 202.7 254.6 304.8 Note (5) Note (5) Note (5) Note (5) Note (5)
22.9 28.2 34.9 43.7 50.0 62.5 75.4 91.4
104.1 116.8 144.4 171.4 222.2 277.4 328.2 360.2 411.2 462.3 514.4 616.0
1011131416171921. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
W d R n tf tf Ah
21.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0610.0
T
1616182123293232373743475156616469707483
N - 2,395
115 125135155165190210230255280320380445520585650710775915
66.782.688.998.4
114.3127.0149.2168.3184.2200.0235.0269.9330.2387.4450.8514.4571.5628.6685.8812.8
5/83/43/43/47/83/47/87/87/87/87/87/81
.1 1/81 1/41 1/41 3/81 3/81 3/81 5/8
44444888888
1212 16 16 20 20242424
12.714.315.917.519.120.723.927.028.630.233.435.039.746.149.352.455.658.862.068.3
14.315.917.519.120.722.325.428.630.231.835.036.641.347.750.854.057.260.463.569.9
384854647084
100117133146 178206260321375425483533587702
21242525293237414346495160657175818794
105
515660646768757879849797
110116129141144157160167
2225272730333843444851526295
102111121130140152
DIMENSION OF CLASS 150 FLANGES
DIMENSION OF CLASS 300 FLANGES
354351647392
105127140157186216270324381413470533584692
354351647392
105127140157186216270324381413470533584692
BLIND RAISED FACE FLANGE WELD NECK RAISED FACE FLANGE SOCKET WELD RAISED FACE FLANGE
THREADED RAISED FACE FLANGE SLIP ON RAISED FACE FLANGE LAPPED JOINT FLANGE
L/J W/N & S/W
S/O & S/WB B
W/N & S/W
E.mail : @forxarind.com web : www.forxarind.com. sales
Q u a l i t y a t C o r e
3
Bellow Seal
Zero Emission
NB NPS O XS/O & S/W W/N L/J
Y Y YS/O & S/W L/J
B B F
152025324050658090
100125150200250300350400450500600
1/23/41
1 1/41 1/2
22 1/2
33 1/2
4568
10121416182024
22.2 27.7 34.5 43.2 49.5 61.9 74.6 90.7
103.4 116.1 143.8 170.7 221.5 276.2 327.0 359.2 410.5 461.8 513.1 616.0
W/NNote (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)
22.9 28.2 34.9 43.7 50.0 62.5 75.4 91.4
104.1 116.8 144.4 171.4 222.2 277.4 328.2 360.2 411.2 462.3 514.4 616.0
1011131416171921. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
W d BR
354351647392
105127140157186216270324381413470533584692
n tf Ah
21.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0610.0
T
1616182123293235404248515866707478808393
95115 125135155165190210230275330355420510560605685745815940
66.782.688.998.4
114.3127.0149.2168.3184.2215.9266.7292.1349.2431.8489.0527.0603.2654.0723.9838.2
5/83/43/43/47/83/47/87/811
1 1/81 1/81 1/41 3/81 3/81 1/21 5/81 3/41 3/4
2
44444888888
1212 16 20 20 20202424
14.315.917.520.722.325.428.631.835.038.144.547.755.663.566.769.976.282.688.9
101.6
384854647084
100117133152189222273343400432495546610718
22252729323741464954606776869294
106117127140
525762677073798386
102114117133152156165178184190203
22252729323741464954606776
111117127140152165184
DIMENSION OF CLASS 600 FLANGES
NB NPS O XS/O & THR. W/N L/J
Y Y YS/O & S/W L/J
B B
80100125150200250300350400450500600
34568
10121416182024
90.7 116.1 143.8 170.7 221.5 276.2 327.0 359.2 410.5 461.8 513.1 616.0
N - 4
Note (2) Note (2) Note (2)Note (2) Note (2) Note (2)Note (2) Note (2)Note (2) Note (2) Note (2)Note (2)
91.4 116.8 144.4 171.4 222.2 277.4 328.2 360.2 411.2 462.3 514.4 616.0
W d BR
127157186216270324381413470533584692
n tf Ah
88.9114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0610.0
T
4248545864727783868993
102
N - 2
240290350380470545610640705785855
1040
190.5235.0279.4317.5393.7469.9533.4558.8616.0685.8749.3901.7
11 1/41 3/81 1/41 1/21 1/21 1/21 5/81 3/4
22 1/82 5/8
888
1212 16 20 20 20202020
38.144.550.855.663.569.979.485.888.9
101.6108.0139.7
127159190235298368419451508565622749
54707986
102108117130133152159203
102114127140162184200213216229248292
54707986
114127143156165190210267
N - 3Size Ω to 2 Ω are identical to class 1500
(1) This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 deg on threaded, slip-on, socket- welding, and lapped flanges. This dimension is defined as the diameter at the intersection between the hub taper and back face of the flange.
NOTES:
(2) To be specified by the Purchaser.(3) 7.0 mm (0.06 in.) raised face for Class 600 and 900 raised face flanges (4) Socket welding flanges may be provided in NPS Ω to NPS 2 Ω , using Class 1500 dimensions.
DIMENSION OF CLASS 900 FLANGES
BLIND RAISED FACE FLANGE WELD NECK RAISED FACE FLANGE SOCKET WELD RAISED FACE FLANGE
THREADED RAISED FACE FLANGE SLIP ON RAISED FACE FLANGE LAPPED JOINT FLANGE
E.mail : @forxarind.com web : www.forxarind.com. sales
(1) This dimension is for the large end of the hub, which may be straight or tapered. Taper shall not exceed 7 degree on threaded, slip-on, socket- welding and lapped flanges. This dimension is defined as the diameter at the intersection between the hub taper and back face of the flange.
NOTES:
(2) To be specified by the Purchaser.(3) 7.0 mm (0.06 in.) raised face for Class 600 and 900 raised face flanges
DIMENSION OF CLASS 1500 FLANGES NB NPS O X
S/O & S/W W/N L/JY Y Y
S/O & S/W L/JB B F
1520253240506580
100125150200250300350400450500600
Ω3/41
1 1/41 1/2
22 Ω34568
10121416182024
W/NNote (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)
22.9 28.2 34.9 43.7 50.0 62.5 75.4 91.4
116.8 144.4 171.4 222.2 277.4 328.2 360.2 411.2 462.3 514.4 616.0
10111314161719. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
W d BR n tf Ah
21.326.733.442.248.360.373.088.9114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0610.0
T
120130150160180215245265310375395485585675750825915985
1170
82.688.9
101.6111.1123.8165.1190.5203.2241.3292.1317.5393.7482.6571.5635.0704.8774.7831.8990.6
7/87/811
1 1/81
1 1/81 1/41 3/81 5/81 1/21 3/4
22 1/82 3/82 5/82 7/83 1/83 5/8
4444488888
1212 12161616161616
22.325.428.628.631.838.141.347.754.073.182.692.1
108.0123.9133.4146.1162.0177.8203.2
3844526470
105124133162197229292368451495552597641762
6070737383
102105117124156171213254283298311327356406
323541414457647390
105119143178219241260276292330
23262931323948
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
32354141445764. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
22.227.734.543.249.561.974.6. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
354351647392
105127157186216270324381413470533584692
DIMENSION OF CLASS 2500 FLANGES NB NPS O X
S/O & S/W W/N L/JY Y Y
L/JB
1520253240506580
100125150200250300
Ω3/41
1 1/41 1/2
22 Ω34568
1012
W/NNote (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)Note (2)
22.9 28.2 34.9 43.7 50.0 62.5 75.4 91.4
116.8 144.4 171.4 222.2 277.4 328.2
W d BR n tf Ah
21.326.733.442.248.360.373.088.9114.3141.3168.3219.1273.0323.8
T
135140160185205235265305355420485550675760
88.995.2
108.0130.2146.0171.4196.8228.6273.0323.8368.3438.2539.8619.1
7/87/81
1 1/81 1/41 1/81 1/41 3/81 5/81 7/82 1/82 1/82 5/82 7/8
44444888888
1212 12
30.231.835.038.144.550.957.266.776.292.1
108.0127.0165.1184.2
435157737995
114133165203235305375441
73798995
111127143168190229273318419464
4043485260707992
108130152178229254
29323539455158
. . .
. . .
. . .
. . .
. . .
. . .
. . .
40434852607079. . .. . .. . .. . .. . .. . .. . .
354351647392
105127157186216270324381
Q u a l i t y a t C o r e
4
Bellow Seal
Zero Emission
(4) Socket welding flanges may be provided in NPS Ω to NPS 2 Ω , using Class 1500 dimensions.
BLIND RAISED FACE FLANGE WELD NECK RAISED FACE FLANGE SOCKET WELD RAISED FACE FLANGE
THREADED RAISED FACE FLANGE SLIP ON RAISED FACE FLANGE LAPPED JOINT FLANGE
E.mail : @forxarind.com web : www.forxarind.com. sales
Q u a l i t y a t C o r e
5
Bellow Seal
Zero Emission
ClassWeld Neck Flanges
1520253240506580
100150200250300350400450500550600
1/22
1/23/411/411/212
34
6810 12 14 16 18 20 24
Size
0.50.71.11.51.82.74.45.27.59.211.018.325.039.051.060.071.088.0119.0
0.91.51.92.63.33.65.47.411.916.020.231.044.364.088.0113.0134.0171.0238.0
0.91.51.92.63.34.76.58.7
18.130.536.256.591.0
105.0127.0178.0216.0268.0380.0
. . .
. . .
. . .
. . .
. . .
. . .
. . .15.024.037.050.085.0
127.0170.0198.0224.0300.0374.0680.0
1.92.63.84.46.111.115.520.430.558.070.0
125.0204.0303.0427.0570.0740.0935.0
1515.0
3.64.06.09.0
13.019.024.043.066.0111.0172.0261.0485.0730.0
. . .
. . .
. . .
. . .
. . .
Class
0.40.70.81.11.42.23.64.15.66.37.5
12.618.528.036.046.050.064.089.0
0.71.11.41.82.63.44.46.1
10.112.514.124.637.150.070.090.0112.0133.0208.0
0.81.41.62.13.13.75.47.3
15.824.529.543.070.086.0
100.0142.0175.0232.0330.0
. . .
. . .
. . .
. . .
. . .
. . .
. . .11.619.832.041.078.0110.0149.0181.0194.0274.0332.0637.0
1.72.33.43.95.49.8
13.718.027.852.061.0
104.0175.0264.0
. . .
. . .
. . .
. . .
. . .
5
ClassBlind Flanges
0.40.70.91.31.62.64.15.07.19.011.821.030.045.059.079.097.0
124.0188.0
0.71.21.52.02.93.45.17.011.815.521.335.257.082.0
106.0140.0178.0223.0345.0
0.71.21.52.03.24.36.08.0
18.028.535.558.098.0
125.0151.0215.0287.0366.0532.0
. . .
. . .
. . .
. . .
. . .
. . .
. . .13.122.136.547.482.5
123.0174.0231.0280.0400.0503.0950.0
1.82.43.64.15.8
10.114.019.030.058.072.0
122.0210.0315.0423.0590.0795.0
1030.01650.0
3.04.55.08.011.017.025.039.060.0
101.0156.0242.0465.0665.0
. . .
. . .
. . .
. . .
. . .
150 300 600 900 1500 2500Class
Lapped Flanges
1520253240506580
100150200250300350400450500550600
1/22
1/23/411/411/212
34
6810 12 14 16 18 20 24
DN NPS
Size
0.40.70.81.11.42.23.64.15.66.37.5
12.618.528.042.052.058.074.0
101.0
. . .
. . .
. . .
. . .
. . .
. . .
. . .11.619.832.041.275.0115.0155.0170.0210.0298.0370.0710.0
1.72.33.43.95.49.8
13.718.027.852.061.0
104.0220.0287.0405.0525.0670.0810.0
1290.0
3.04.05.08.011.017.025.038.058.095.0
146.0220.0420.0500.0
. . .
. . .
. . .
. . .
. . .
5
0.71.11.41.82.63.44.46.1
10.112.514.124.842.064.084.0114.0134.0168.0250.0
0.81.41.62.13.13.75.47.3
15.824.529.543.077.092.0114.0160.0192.0260.0368.0
150 300 600 900 1500 2500Class
Threaded Flanges
0.40.70.91.21.52.33.74.25.97.08.4
13.017.829.539.042.054.068.093.0
0.71.21.41.92.83.34.66.3
10.212.918.026.037.552.072.0
100.0126.0148.0222.0
1.01.61.82.63.33.96.07.4
17.026.532.046.074.090.0
108.0150.0188.0230.0325.0
. . .
. . .
. . .
. . .
. . .
. . .
. . .11.920.032.541.777.5110.0149.0181.0194.0274.0332.0637.0
1.72.43.54.05.5
10.013.9. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
3.04.05.08.011.017.025.0. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
150 300 600 900 1500 2500Class
Socket Welding Flanges
1.72.43.54.05.5
10.013.9. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
0.40.70.81.11.42.23.64.1. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
0.71.21.41.92.83.34.66.3. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
1.01.61.82.63.33.96.07.4. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
150 300 600 900 1500 2500DN NPS 150 300 600 900 1500 2500 150 300 600 900 1500 2500. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .
Slip On FlangesAPPROX. WEIGHTS OF FLANGES
E.mail : @forxarind.com web : www.forxarind.com. sales
Ordering Information
Q u a l i t y a t C o r e
6
Bellow Seal
Zero Emission
As Per Our Design
Type Of Materials Nomen.1) Materials
S S310SS304 / ASTM A182 Gr. F304
SS304 LSS316
SS316LSS317SS321SS446
Monal 400Incoloy 625Incoloy 825
Carbon SteelA105
Alloy 20ASTM A182 F51 (Duplex F51)ASTM A182 F60 (Duplex F60)
ASTM A182 F53 (Super Duplex F53)ASTM A312 TP 304L
ASTM A182 F11 ASTM A182 Gr. F5ASTM A312 TP 304
Hastelloy C276A350 Gr. LF1/ LF2/ LF3
SS410ASTM A240 TP 316L
Inconel-600ASTM A234 Gr. WPB
Mild SteelNickel AlloyGalvanized
S1 S4 S4L S6 S6L S7
S21 S46 M4 I6 I8 CS A1
A20 F51 F60 F53 P4L F11 F5
TP4 HC2 LF2 S41 P6L I60
WPB MS NAGLV
8" 10" 12" 14" 16" 18"20" 22" 24" 26" 28" 30" 32" 36"
Size Nomen.68
101520253240506580
100125150200250300350400450500550600650700750800900
1/8" 1/4" 3/8" 1/2" 3/4" 1"
1 1/4" 1 1/2"
2" 2 1/2"
3" 4"5" 6"
2) Sizes
Type Nomen.4) Type Of Face
Types Nomen.#150 #300 #400#600#900
#1500#2500#4500S10S20S40S80
S160SXXS
FED
Class 150 Class 300 Class 400 Class 600 Class 900
Class 1500 Class 2500 Class 4500
Sch 10 Sch 20 Sch 40 Sch 80
Sch 160 Sch XXS Table F Table E Table D
5) Type Of Class
Type Nomen.3) Type of End Connections.
FL BW SW TG RTJNTBTSN
Flange EndButt Weld End
Socket Weld EndTounge & GrooveRing Type JointNPT Threaded
BSPT ThreadedSW NPT
Flat FaceRaised Face
Ring TypeGrooveTounge
FFRFRTJGR
TNG
Ex. 6” Slipon Raised Face #150 ASTM A182 SS 304 = ___-6-SO-RF-#150-___
E.mail : @forxarind.com web : www.forxarind.com. sales