一、路由器、交换机基本配置
DESCRIPTION
一、路由器、交换机基本配置. 安排. 实验室各机柜设备互连介绍 学生超级终端连接到各设备 学生 PC 通过内部交换机连接到各自的路由器第一个以太网口 路由器基本结构及各配置模式介绍 讲解、学习课件 实验文件 8_ Steps_to_Success.pdf 实验 1.5.1 :网络布线和基本路由器配置. 交换机或路由器的配置模式及切换. Using exit , end and Control-Z. end. exit. 实验一文件. 实验 1.5.1 :网络布线和基本路由器配置 P3:DTE, DCE - PowerPoint PPT PresentationTRANSCRIPT
1
一、路由器、交换机基本配置
2
安排
• 实验室各机柜设备互连介绍• 学生超级终端连接到各设备• 学生 PC 通过内部交换机连接到各自的路由器第一个
以太网口• 路由器基本结构及各配置模式介绍• 讲解、学习课件• 实验文件
–8_Steps_to_Success.pdf
–实验 1.5.1 :网络布线和基本路由器配置
3
交换机或路由器的配置模式及切换
4
exit
end
Using exit, end and Control-Z
5
实验一文件
• 实验 1.5.1 :网络布线和基本路由器配置–P3:DTE, DCE
–P4: 通过控制台连接配置路由器时需要用到终端仿真软件。 Cisco Networking Academy 推荐使用 Tera Term 。–P5:[OK] 提示与输入–关于 setup
–P7: 步骤 10 :键入缩写的 IOS 命令。–P8: 步骤 5 :使用 no ip domain-lookup 命令禁用 DNS 查找。
• 实验 1.5.2 :基本路由器配置• 实验 1.5.3 :路由器配置练习
6
实验一文件
• 实验 1.5.2 :基本路由器配置–show running-config
–show ip route
–show ip interface brief
• 实验 1.5.3 :路由器配置练习
7
实验网络拓扑图
8
路由器配置的基本步骤
• Step 1: Physical Connections • Step 2: Boot up the router • Step 3: Host Name and Passwords • Step 4: Adding IP Addresses • Step 5a: Adding Dynamic Routing: RIP • Step 5b: Adding Dynamic Routing: EIGRP • Step 5c: Adding Dynamic Routing: OSPF• Step 6: Adding Default and Static Routes • Step 7: Testing and Monitoring • Step 8: Finishing up• 详见文档: 8_Steps_to_Success.pdf
9
实验要求及验证• 路由器基本配置
–设备命名–各种口令( console; enable; vty )–第一个以太网口分配地址–int fa0/0
–ip add 192.168.1.1 255.255.255.0
–no shut
• 将 PC 机的网线从校园网拔出,转接到内网,• 自己的 PC 通过交换机连到路由器的第一个以太网口,修改自己的 IP 地址和路由
器在同一个网段中, PC 机的网关地址指向所连接的路由器的接口地址如:• 192.168.*.10 255.255.255.0
• * 的值和路由器的编号相对应,如 R1 , 192.168.1.10
• C:>telnet 192.168.*.1
• 如果登录成功,则实验成功
10
11
二、静态路由、缺省路由
Role of the Router
Routers are primarily responsible for interconnecting networks by: Determining the best path Forwarding packets
What is the best path to 192.168.2.0/24 network?
Introducing the Topology
172.16.3.0/24
172.16.2.0/24
172.16.1.0/24
192.168.1.0/24
192.168.2.0/24
.1
.1
.1
.1
.2 .2
.1
14
实验文件
• 实验手册 ccna2-路由-学生版实验手册
–实验 2.8.1 :基本静态路由配置–实验 2.8.2 :静态路由配置练习–实验 2.8.3 :静态路由故障排除
15
实验文件• 拓扑结构及地址表结合实验室具体情况进行
16
路由器配置的基本步骤
• Step 1: Physical Connections • Step 2: Boot up the router • Step 3: Host Name and Passwords • Step 4: Adding IP Addresses • Step 5a: Adding Dynamic Routing: RIP • Step 5b: Adding Dynamic Routing: EIGRP • Step 5c: Adding Dynamic Routing: OSPF• Step 6: Adding Default and Static Routes • Step 7: Testing and Monitoring • Step 8: Finishing up• DEMO: debug ip routing• Show ip route• 直连的网络和静态路由加入的远程网络
17
常用命令
• Show ip int brief
• Show run
• Show ip route
• Show version
• Show controller s0/0/0
Examining the show commands
• show interfaces – Displays all the statistics for all the interfaces on the router. To view the statistics for a specific interface, enter the show interfaces command followed by the specific interface and port number.
• show controllers serial – Displays information-specific to the interface hardware
• show clock – Shows the time set in the router • show hosts – Displays a cached list of host names and addresses • show users – Displays all users who are connected to the router • show history – Displays a history of commands that have been entered • show flash – Displays information about flash memory and what IOS files are
stored there • show version – Displays information about the router and the IOS that is
running in RAM • show ARP – Displays the ARP table of the router • show protocol – Displays the global and interface specific status of any
configured Layer 3 protocols • show startup-configuration – Displays the saved configuration located in
NVRAM
• show running-configuration – Displays the configuration currently running in RAM
补充说明
• 1 、结合实验室的具体情况进行连线及有关说明• 主机要连接到内网中,同时修改主机地址为静态分配,以各自所在的路
由器的第一个以太网口为网关• 如果是 4 人一组,则要增加一台路由器 R4 ( 2611 ),通过以太网口
E0/0 直接连接到 R2 的 F0/0
• 一定要注意各个路由器的接口信息, # show ip int brief 查看,路由器2611 是 ethernet 的 10M 口,而 2620 , 2621 , 1841 , 2800 等都是fastethernetde 100M 口。另外, 2620 只有 1 个以太网口,而其他的则有 2 个以太网口。
• 机柜中的 R3 可能是下列中的一种: 2621 , 2620 或 2611
• DCE 、 DTE 线缆根据线缆的实际连接来判断,但一定不要忘记在 DCE端敲入 clock rate 命令,如果不能确定是否 DCE ,可用命令Router#show controllers s0/0/0 进行查看
• 各接口配置完地址等信息后,一定不要忘记敲入 no shut 命令• 2 、地址分配各组成员之间协商,地址可以自己设计和分配。
关于各个路由器之间的路由实现说明
• R1 :默认静态路由• R2 :静态路由• R3 :先静态路由,再更换为汇总结静态路由总路由• R4 :默认静态路由
静态路由与缺省路由
R1(config)#ip route 0.0.0.0 0.0.0.0 172.16.2.2
静态路由、缺省路由拓展
• 如果有 R4 ,则将 R4 也作为分支机构如 Branch2 即可。• 此时, R4 启用缺省路由, HQ 启用静态路由。
23
Print out this topology
24
基本配置 R2 conf t
host R2
enable secret class
line con 0
password cisco
login
line vty 0 4
password cisco
login
end
****R2
conf t
int fa0/0
description connet to LAN2
ip add 172.16.1.1 255.255.255.0
no shut
int s0/0/0
ip add 172.16.2.2 255.255.255.0
no shut
int s0/0/1
ip add 192.168.1.2 255.255.255.0
clock rate 56000
no shut
end
25
基本配置 R1&R3
***R1
conf t
int fa0/0
description connet to LAN1
ip add 172.16.3.1 255.255.255.0
no shut
int s0/1/0
ip add 172.16.2.1 255.255.255.0
clock rate 56000
no shut
end
***R3
conf t
int fa0/0
description connet to LAN3
ip add 192.168.2.1 255.255.255.0
no shut
int s0/0/1
ip add 192.168.1.1 255.255.255.0
no shut
end
26
静态路由
***R1
conf t
ip route 172.16.1.0 255.255.255.0 172.16.2.2
ip route 192.168.1.0 255.255.255.0 172.16.2.2
ip route 192.168.2.0 255.255.255.0 172.16.2.2
缺省路由简化路由表 ip route 0.0.0.0 0.0.0.0 172.16.2.2
***R2
conf t
ip route 172.16.3.0 255.255.255.0 172.16.2.1
ip route 192.168.2.0 255.255.255.0 192.168.1.1
***R3
conf t
ip route 172.16.1.0 255.255.255.0 192.168.1.2
ip route 172.16.2.0 255.255.255.0 192.168.1.2
ip route 172.16.3.0 255.255.255.0 192.168.1.2
汇总路由简化路由表 ip route 172.16.0.0 255.255.252.0 192.168.1.2
27
实际的网络
***R1
conf t
ip route 172.16.1.0 255.255.255.0 172.16.2.2
ip route 192.168.1.0 255.255.255.0 172.16.2.2
ip route 192.168.2.0 255.255.255.0 172.16.2.2
缺省路由简化路由表 ip route 0.0.0.0 0.0.0.0 172.16.2.2
***R2
conf t
ip route 172.16.3.0 255.255.255.0 172.16.2.1
ip route 0.0.0.0 0.0.0.0 192.168.1.1
***R3
conf t
ip route 172.16.1.0 255.255.255.0 192.168.1.2
ip route 172.16.2.0 255.255.255.0 192.168.1.2
ip route 172.16.3.0 255.255.255.0 192.168.1.2
汇总路由简化路由表 ip route 172.16.0.0 255.255.252.0 192.168.1.2
28
实际的网络
***R1
conf t
缺省路由简化路由表 ip route 0.0.0.0 0.0.0.0 172.16.2.2
***R2
conf t
ip route 172.16.3.0 255.255.255.0 172.16.2.1
ip route 0.0.0.0 0.0.0.0 192.168.1.1
***R3
conf t
汇总路由简化路由表 ip route 172.16.0.0 255.255.252.0 192.168.1.2
系统测试
• 路由器– Show run– Show ip int brief– Debug ip routing 实时观察路由的变化– Undebug ip routing/ undebug all 关闭 debug– Show ip route– Ping 远程主机– Traceroute 远程主机– telnet 远程路由器
• PC 机– Ping 远程主机– telnet 远程路由器