4rigging frame installation guide - digital projection · transportation, installation and...

Rev B March 2015115-918B

HIGHlite 660 / 740 / 8000 SeriesHIGHlite Laser 3D Series

M-Vision 930 SeriesTitan LED / 800 / 930 / Quad Series

RIGGING FRAME INSTALLATION GUIDE4

page i

Digital Projection

Rigging Frame Installation Guide Rev B March 2015

About This DocumentFollow the instructions in this manual carefully to ensure safe and long-lasting use of the rigging frame.

Symbols used in this manualMany pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:

WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.

NOTE: this symbol indicates that there is some important information that you should read.

Product revisionBecause we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice.

Legal noticeTrademarks and trade names mentioned in this document remain the property of their respective owners. Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.

Copyright © 2015 Digital Projection Ltd. All rights reserved.

Notes

page ii

Digital Projection


Safety InformationPlease follow the instructions in this document carefully to ensure a safe installation.

Please consider keeping the original box and packing materials in case you ever need to ship the frame.

Safety warnings

INTENDED USE

Thisriggingframeisintendedforusebyfullyqualified,trainedandcompetentpersonsasanaidtoprovidesafeandsecuretransportation,installationandadjustmentofprojectors.

Onlyusetheframeindoors,wherethereisnowind.

This frame is intended for use only with the projectors listed in Which Products Are Compatible With This Frame? further in thismanual.Anyattempttousetheframewithotherprojectorsmayresultinsevereinjuryordamage.

MAINTENANCE AND INSPECTION

TheRiggingFrameisamaintenancefreeproduct.However,beforecarryingoutaninstallationitisessentialtoensurethat:

• No screws are missing and all screws are in the right position.

• Noscrews,adjustmentwheelsorothercomponentsaredamaged.

• Noplates,squarepipesorothercomponentsarebentorbroken.

Use a suitable tool to test each screw and make sure that none are loose.

Afteraninstallation,ensurethatallscrews,washersandinsulationsarepresentandpositionedcorrectly.

Notes

page iii

Digital Projection


INSTALLATION AND MOUNTING

Installation errors may lead to serious accidents.

Installationshouldonlybecarriedoutbyqualifiedpersonnel.

Installation should be carried out by a minimum of two persons.

Donotplacetheprojectoronslopedorunstablesurfacesasitmayfallortipover,resultingininjuryordamage.Makesurethe surface can support a weight of 210 kg (462.97 lb).

Donotexceedthemaximumweightloadsforceilingmounts.Forsuspendedinstallations,useonlydesignatedhangingaccessories such as the truss mount and the 750 kg Doughty clamp for a maximum weight load of 138 kg (304.23 lb).

Whenstackingprojectors,makesureallfourthreadedrodsaretightenedwithatorqueof5Nm.

Donotpositiontheframeinamannerwhichmayimpedeprojectorventilation.Poorventilationmayresultinafire.Ensurethatthereisatleast30cm(12in)ofspacebetweentheventilationoutletsandanywall,and10cm(4in)onallothersides.

Preventpropertydamageandpersonalinjurycausedbyincorrectinstallation.Ensuretheframeisingoodcondition,theinstallationhasbeencarriedoutproperlyandtheloadcapacityofthesupportingstructureissufficienttocarrytheweightoftheentireinstallation,upto150kg(330.69lb)incl.lenses,cabling,etc.

Do not operate the projector in humid or dusty places or in places where the projector may come into contact with oily smokeorsteam.Usingtheprojectorinsuchconditionsmayresultinfire,electricshocksorplasticdeterioration.

Notes

page iv

Digital Projection


SAFE HANDLING

Avoidinjuryfromfallingobjectsduringassemblyanddisassemblyoftheframe.Wearprotectiveshoes,glovesandhelmet.

Theframeisheavy.Usesafehandlingtechniqueswhenliftingtheframe.

Wearsafetyglovestopreventfingersbeingcaughtbetweentheouterringsandtheplates.Whenadjustingtheimage,keepyour hands on the adjustment wheels at all times as shown below. Do not lean on the frame.

Notes

page v

Digital Projection


Which Products Are Compatible With The Rigging Frame?The rigging frame can be used with the following projectors:Products Badges• HIGHlite Laser 3D

HIGHlite

3D

LASER

• HIGHlite 660 and 740 2D• HIGHlite 660 3D• HIGHlite 8000

HIGHlite

2D

660740

HIGHlite

3D

660

HIGHlite

2D

8000

• M-Vision 930 3D M-Vision

3D

930

• Titan LEDLED

3D

• Titan 800 and Titan 930

2D

800

3D

800

2D

930

3D

930

• Titan Quad Series:• Titan Quad• Titan Super Quad / Quad 2000

2D

Quad

3D

Quad

2D

QuadSuper

3D

QuadSuper

2D

Quad2000

3D

Quad2000

Notes

Any attempt to use the frame with other projectors may result in severeinjuryordamage.

Digital Projection


IN THIS GUIDE

What’s In The Box? ............................................................................................. 1

Fitting HIGHlite Laser In The Frame ............................................................ 2Required parts .............................................................................................................2Setup ............................................................................................................................2Order of components in assembly with HIGHlite Laser ..........................................6

Fitting M-Vision 930 In The Frame ................................................................ 7Required parts .............................................................................................................7Setup ............................................................................................................................7Order of components in assembly with M-Vision 930 ...........................................11

Fitting Titan In The Frame ............................................................................. 12Required parts ...........................................................................................................12Setup ..........................................................................................................................13Order of components in assembly with Titan ........................................................16

Fitting HIGHlite In The Frame....................................................................... 17Required parts ...........................................................................................................17Setup ..........................................................................................................................17Order of components in assembly with HIGHlite ...................................................21

Adjustment Options .......................................................................................... 22Roll .............................................................................................................................22Pitch ...........................................................................................................................22Yaw .............................................................................................................................22

Stacking Projectors ......................................................................................... 23

Ceiling Installation ........................................................................................... 24Ceiling installation using 750 kg / 1650 lb Doughty clamps .................................24

Safe fitting areas - bottom ...............................................................................................25Safe fitting areas - top .....................................................................................................26

Ceiling installation using the truss mount (optional accessory) .........................27Adjusting ceiling installations with the truss mount .............................................28

Maximum Weight Loads .................................................................................. 29Truss mount installations .........................................................................................29Ceiling installation using 750 kg / 1650 lb Doughty clamps .................................30Table mounts .............................................................................................................31

Dimensions .......................................................................................................... 32Rigging frame ............................................................................................................32Truss mount ...............................................................................................................33

Digital Projection

Rigging Frame Installation Guide

WHAT’S IN THE BOX?

Rev B March 2015

What’s In The Box? Notes

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.

You should save the original box and packing materials, in case you ever need to ship the rigging frame.

The frame is shipped with all components listed here. However, some projectors do not use all screws, sleeves and washers supplied. To find out which parts you need for your installation, refer to the relevant projector section:

• Fitting HIGHlite Laser In The Frame

• Fitting M-Vision 930 In The Frame

• Fitting Titan In The Frame

• Fitting HIGHlite In The Frame

1 x rigging frame 115-919

4 x M10x25 low profile socket head screws

115-921

4 x ø10 insulation washers 115-922

4 x ø10 insulation sleeves 115-923

6 x M6x20 button head screws 115-924

12 x ø6.2 insulation sleeves 115-925

4 x square to round adaptors 115-920

Rigging Frame Installation Guide 115-918

4 x ø10.5 insulation spacers 115-994

6 x ø6 spring lock washers 116-226

Digital Projection


FITTING HIGHLITE LASER IN THE FRAME

Rev B March 2015

Fitting HIGHlite Laser In The FrameHIGHlite

3D

LASER

Required partsPart Quantity

Rigging frame 1

M10x25 low profile socket head screws 4ø10 insulation washers 4

ø10 insulation sleeves 4

M6x20 button head screws 6

ø6 spring lock washers 6

ø6.2 insulation sleeves 12

Setup1. Remove the lens hood.

2. Place the projector upside down on a suitable flat surface and remove the four adjustable feet 1 .

3. Place the ø10 insulation washers over each M10 screw hole 2 .

Notes

This procedure requires two persons.

It is important to use the washers astheyprovidegalvanicisolation.

1

1

1

1

2

2

2

2

Digital Projection



Rev B March 2015

Setup (continued)

4. Insert six of the ø6.2 insulation sleeves in the M6 screw holes 3 on the inside of the frame.

Notes


.

Itisimportanttousethesleevesastheyprovidegalvanicisolation.

3

3

3

3

3

3

Digital Projection



Rev B March 2015

Setup (continued)5. Position the rigging frame over the projector so that the adjustment screws 4 are at the back, aligning the M10 5 and

M6 screw holes 6 .

Ensure that the projector plate 7 is flat against the body of the projector.

This can be achieved by placing the projector on a surface which is smaller than the frame, allowing full contact between the plate and the projector.

Notes


.

4

4

6

5

5

6

6

5

5

6

6 6

7

Digital Projection



Rev B March 2015

Setup (continued)

6. Place the ø10 insulation sleeves over each M10 hole. Secure the four M10x25 low profile socket head screws 8 into each hole. Ensure each screw runs through the corresponding sleeve and washer and catches into the corresponding M10 hole in the projector surface.

7. Place the other six ø6.2 insulation sleeves over each M6 screw hole. Place a ø6 spring lock washer over each ø6.2 insulation sleeve. Secure the six M6x20 button head screws 9 into each hole. Ensure each screw runs through the sleeve and washer and catches into the corresponding M6 hole in the projector surface.

Notes


Itisimportanttousethesleevesandwashersastheyprovidegalvanicisolation.

Torque: 4±0.5 N m.

8

9

8

9

9

8

8

9

9

9

Digital Projection



Rev B March 2015

Order of components in assembly with HIGHlite Laser

1 M10x25lowprofilesocketheadscrew

2 ø10insulationsleeve

3 Projector plate

4 ø10 insulation washer

5 M6x20 button head screw

6 ø6 spring lock washer

7 ø6.2insulationsleeve

Notes

1

2

3

4

5

6

3

7

7

Notes


Itisimportanttousethesleevesandwashersastheyprovidegalvanicisolation.

Torque: 4±0.5 N m.

Digital Projection


FITTING M-VISION 930 IN THE FRAME

Rev B March 2015

Fitting M-Vision 930 In The FrameM-Vision

3D

930


Rigging frame 1




Setup1. Place the projector upside down on a suitable flat surface and remove

the four adjustable feet 1 .

Notes



1

1

1

1

Digital Projection



Rev B March 2015

Setup (continued)


Notes


.


2

2

2

2

2

2

Digital Projection



Rev B March 2015

Setup (continued)

3. Position the rigging frame over the projector so that the adjustment screws 3 are at the back, aligning the M6 screw holes 4 .



Notes


3

3

4

4

4

4

4 4

5

Digital Projection



Rev B March 2015

Setup (continued)

4. Place the other six ø6.2 insulation sleeves over each M6 screw hole. Place a ø6 spring lock washer over each ø6.2 insulation sleeve. Secure the six M6x20 button head screws 6 into each hole. Ensure each screw runs through the sleeves and catches into the corresponding M6 hole in the projector surface.

Notes



Torque: 4±0.5 N m.6

66

6

6

6

Digital Projection



Rev B March 2015

Order of components in assembly with M-Vision 930




4 Projector plate

1

2

4

3

3

Notes



Torque: 4±0.5 N m.

Digital Projection


FITTING TITAN IN THE FRAME

Rev B March 2015

Fitting Titan In The Frame

LED

3D 2D

800

3D

800

2D

930

3D

930

2D

Quad

3D

Quad

2D

QuadSuper

3D

QuadSuper

2D

Quad2000

3D

Quad2000

Required parts

Part Quantity

Rigging frame 1

M10x25 low profile socket head screws 4ø10 insulation sleeves 4

ø10.5 insulation spacers 4

Notes


Digital Projection



Rev B March 2015

Setup


2. Place the ø10.5 insulation spacers over each M10 screw hole 2 .

Notes



1 1 1 2 2 21 2

Digital Projection



Rev B March 2015

Setup (continued)




Notes


3

3

4

4

4

4

5

Digital Projection



Rev B March 2015

Setup (continued)

4. Place the ø10 insulation sleeves over each M10 hole. Secure the four M10x25 low profile socket head screws 6 into each hole. Ensure each screw runs through the corresponding sleeve and washer and catches into the corresponding M10 hole in the projector surface.

Notes



Torque: 4±0.5 N m.

6

6

6

6

Digital Projection



Rev B March 2015

Order of components in assembly with Titan

1 M10x25lowprofilesocketheadscrew

2 ø10insulationsleeve

3 Projector plate

4 ø10.5 insulation spacer

Notes



Torque: 4±0.5 N m.

1

2

3

4

Digital Projection


FITTING HIGHLITE IN THE FRAME

Rev B March 2015

Fitting HIGHlite In The FrameHIGHlite

2D

660740

HIGHlite

3D

660

HIGHlite

2D

8000


Rigging frame 1




Setup


Notes


1

1

1

1

Digital Projection



Rev B March 2015

Setup (continued)


Notes



2

2

2

2

2

2

Digital Projection



Rev B March 2015

Setup (continued)




Notes


3

3

4

4

4

4

4 4

5

Digital Projection



Rev B March 2015

Setup (continued)

4. Place the other six ø6.2 insulation sleeves over each M6 screw hole. Place a ø6 spring lock washer over each ø6.2 insulation sleeve. Secure the six M6x20 button head screws 6 into each hole. Ensure each screw runs through the sleeves and catches into the corresponding M6 hole in the projector surface.

Notes



Torque: 4±0.5 N m.6

6

6

6

6

6

Digital Projection



Rev B March 2015

Order of components in assembly with HIGHlite




4 Projector plate

Notes



Torque: 4±0.5 N m.

1

2

4

3

3

Digital Projection


ADJUSTMENT OPTIONS

Rev B March 2015

Adjustment Options

RollUse the adjusting screws on the left and right to roll the projector by approximately ±5º. Use the adjusting screw on the left to roll to the left and the screw on the right to roll to the right.

PitchUse the two adjusting screws to adjust the pitch by approximately ±5º. Apply equal adjustment to both screws.

YawUse the adjustment screw positioned underneath the projector to adjust the yaw by approximately ±5º.

Notes

±5º ±5º

±5º

±5º

Digital Projection


STACKING PROJECTORS

Rev B March 2015

Stacking Projectors1. Position the top projector so that the four stacking holes 1 are exactly above the M8 threaded rods 2 .

2. To secure the installation, tighten by hand using the wing nut 3 until it is very difficult to turn one more time.

3. Tighten the M8 nut 4 with a torque value of 5 N m using a dynamometric wrench.

Notes


Make sure the screw is in a straightposition,perpendiculartothe frame.

Correct Incorrect

1

2

3

4

Digital Projection


CEILING INSTALLATION

Rev B March 2015

Ceiling Installation

Ceiling installation using 750 kg / 1650 lb Doughty clampsFit the square to round adaptors 1 and secure the clamp to the frame.

Notes

For information on weight restrictions for installations using the Doughty clamps, see Maximum Weight Loads further in this guide.

Parts of the frame are unsuitable for fitting square to round adaptors. See Safe fitting areas - bottom and Safe fitting areas - top for more information.

1

Digital Projection



Rev B March 2015

Safe fitting areas - bottomSquare to round adaptors should only be fitted in the areas shown below.

510 mm (20.07 in)

510 mm (20.07 in)

113

mm

(4.4

4 in

)11

3 m

m (4

.44

in)65

mm

(2.5

5 in

)

113

mm

(4.4

4 in

)11

3 m

m (4

.44

in)

65 m

m (2

.55

in)

Notes


Digital Projection



Rev B March 2015

Safe fitting areas - topSquare to round adaptors should only be fitted in the areas shown below.

Notes


510 mm (20.07 in)

510 mm (20.07 in)

300

mm

(11.

81 in

) 300 mm

(11.81 in)

Digital Projection



Rev B March 2015

Ceiling installation using the truss mount (optional accessory)

Attach the truss mount to the top frame in the stack by driving the screws 1 into the mounting holes on the frame 2 .

1

1

1

1

1

2

Notes

For information on weight restrictions for installations using the truss mount, see Maximum Weight Loads further in this guide.

Torque: 4±0.5 N m.

Digital Projection



Rev B March 2015

Adjusting ceiling installations with the truss mount

Lift the handle 1 to allow 360° rotation adjustment.

The inclination angle can be adjusted by 10% at the upper part (rough adjustment) and by 2% at the lower part (fine adjustment).

Use the four adjustment screws 2 for fine adjustment.

Notes

2

Fine adjustment (up to 2º)

Rough adjustment (up to 10º)

1

360º

Digital Projection


MAXIMUM WEIGHT LOADS

Rev B March 2015

Maximum Weight Loads

Truss mount installationsThe maximum weight load for a truss mount installation is 137.84 kg (302.03 lb). Use the truss mount with up to two projectors per installation, as shown in the illustration.

Notes

Ensure the load capacity of the supportingstructureissufficientto carry the weight of the entire installation,upto150kg(330.69lb)incl.lenses,cabling,etc.

M-Vision 930HIGHlite HIGHlite Laser Titan

Digital Projection



Rev B March 2015

Ceiling installation using 750 kg / 1650 lb Doughty clampsThe maximum weight load for a ceiling installation using Doughty clamps is 137.84 kg (302.03 lb). Use Doughty clamps to mount up to two projectors as shown in the illustration.

Notes

Ensure the load capacity of the supportingstructureissufficientto carry the weight of the entire installation,upto150kg(330.69lb)incl.lenses,cabling,etc.

HIGHlite LaserHIGHlite M-Vision 930 Titan

Digital Projection



Rev B March 2015

Table mountsThe maximum weight load for a table mount installation is 210 kg (462.97 lb). Mount up to three projectors as shown in the illustration.

Make sure the surface can support the weight of the installation.

Notes

HIGHlite Laser HIGHlite M-Vision 930 Titan

Digital Projection


DIMENSIONS

Rev B March 2015

Dimensions

Rigging frame

Notes

Frame only weight: 20 kg / 44.09 lb

695 mm / 27.36 in 360 mm / 14.17 in

670 mm / 26.37 in

815

mm

/ 32

.08

in36

0 m

m /

14.1

7 in

490

mm

/ 19

.29

in

Digital Projection


DIMENSIONS

Rev B March 2015

Truss mount Notes

Truss mount weight: 4.5 kg / 8.81 lb

284

mm

/ 11

.18

in

250.

2 m

m /

9.85

in

164.

7 m

m /

6.48

in

159

mm

/ 6.

26 in

Digital Projection


DIMENSIONS

Rev B March 2015

This page is intentionally left blank.

115-918B Rigging Frame Installation Guide

Contact Information:

Digital Projection Limited

Greenside Way, Middleton Manchester M24 1XX, UKRegistered in England No. 2207264 Registered Office: as aboveTel (+44) 161 947 3300 Fax (+44) 161 684 [email protected] [email protected]

Digital Projection Inc.

55 Chastain Road, Suite 115 Kennesaw, GA 30144, USATel (+1) 770 420 1350 Fax (+1) 770 420 [email protected] www.digitalprojection.com

Digital Projection China

中国北京市朝阳区芍药居北里101号世奥国际中心A座2006室(100029)Rm A2006 ShaoYaoJu 101 North Lane Shi Ao International Center Chaoyang District Beijing 100029, PR CHINA Tel (+86) 10 84888566 Fax (+86) 10 [email protected] www.dp-china.com.cn

Digital Projection Asia

16 New Industrial Road #02-10 Hudson Technocentre Singapore 536204Tel (+65) 6284-1138 Fax (+65) 6284-1238www.digitalprojectionasia.com

www.digitalprojectionasia.com

4rigging frame installation guide - digital projection · transportation, installation and...

Documents