49-n series - amazon s3 series - contempra collection.pdf21 unit start up turn on hot and cold water...
TRANSCRIPT
49-N SeriesSerie 49-NSérie 49-N
Lavatory Widespread FaucetGrifo Extenso Para Baño
Robinet Sans Applique Pour Lavabo
10-12-04 EO6773E 29165-0300A COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYCopyright © 2004, Price Pfi ster, Inc.© 2004, Price Pfi ster, Inc.©
Thank you for purchasing this Price Pfi ster bathroom faucet. All Price Pfi ster products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This bathroom faucet is easy to install using basic tools and our easy to follow illustrated instructions. If you have any questions regarding your bathroom faucet installation call 1-800-Pfaucet (1-800-732-8238).
1 BEFORE PROCEEDING
WARNING: Read all the instructions completely before proceeding. Price Pfi ster recommends calling a professional if you are uncertain about installing this product!This product should be installed in accordance with all local and state plumbing and building codes.
2 SHUT OFF WATER SUPPLYLocate water supply inlets and shut off the water supply valves. These are usually found under the sink or near the water meter. If you are replacing an existing faucet, remove the faucet from the sink and clean the sink surface thoroughly.
3 TOOLS RECOMMENDED• PTFE plumber's tape or thread sealant • Plumber's putty• Slotted screwdriver • Phillips head screwdriver • Pliers • Adjustable wrench • Flashlight • Cloth
Your installation may require new supply lines and/or shut-off valves or other additional tools.
This product comes with an installation tool used for securing the valve body assemblies.
INSTALLATION STEPS
4 SPOUT INSTALLATIONInsert Lift Rod (4A) into hole at the back of Spout (4B). Place Plastic Seal Ring (4C) against the bottom of Spout Body (4D). With Spout (4E) facing forward, carefully install the Lift Rod (4A), Shank (4E) facing forward, carefully install the Lift Rod (4A), Shank (4E 4F) 4F) 4Fand receiving Tube (4G) through the center hole of sink (4H).
5 SECURING FAUCETFrom underneath sink, secure the faucet by placing the Metal Washer (5A) and the Long Nut (5B) (7From underneath sink, secure the faucet by placing the Metal Washer (
7From underneath sink, secure the faucet by placing the Metal Washer (
/16 hex.) onto the Mounting Post (5C). Make sure that the bumps on the Metal Washer (5A) are facing up. Tighten using a fl athead screwdriver or an adjustable wrench until the faucet is fi rmly connected to the sink. Do not over tighten!
6 VALVE BODY ATTACHMENTFrom above sink, insert Valve Body (6A) through Mounting Holes (6B). The HOT valve, labeled with Red Tag (6D), should be positioned to the left side of the spout.
2
3
4
5
6
2
ENGLISH
4C
4E
4D
5A
5B
6A
6A
6B
6B
6D
4G
4F4H
5C
5A 5B
4A
4B4A
7 VALVE BODY INSTALLATIONFrom underneath sink, place Mounting Washer (7B) onto Valve Shank (7A) and tighten with Mounting Nut (7C).
8 SECURING VALVE BODYFrom underneath, tighten Mounting Nut (8A) by using Installation Tool (8B). For better leverage, use a Screwdriver (8C), insert it through Hole (8D) and tighten the Mounting Nut (8A) until Valve (8E) is fi rmly secured to sink.8E) is fi rmly secured to sink.8E
9 HOSE CONNECTION TO SPOUT BODYFrom underneath sink, push the Center Connector (9A) onto receiving Tube (9B), until unable to push any further. Pull down on the quick connect housing (9A). If the housing and the Inner Collet (9D) separate slightly but do not pull off the receiving Tube (9B), the connection is secure.
10 HOSE CONNECTION TO VALVE BODYSlide the End Connectors (10A) onto the Valve Bodies (10B). Push the End Connectors (10A) all the way up until completely seated. Be careful not to damage O-Rings (10C).
7
8
9
10
3
ENGLISH
7A7B
7C
8A
8D
8B
8C
8E 8E
8A8A
8E
9A
9B
10A10A
10A10A
10B
10B
10C
10C
9A 9A 9A
9B 9D9B
12 VALVE ADAPTER ATTACHMENTThread Valve Adapters (12A) onto the Valve Stems (12B) and tighten so that the Valve Adapters (12A) sit on the surface of the Valve Body Washers (12C).
13 HANDLE ATTACHMENTPlace Plastic Seal Rings (13A) against the bottom of Handle Hubs (13B). Connect Handles (13C) onto Valve Adapters (13D).
14 VALVE FUNCTIONValve function – COLD valve: close-counterclockwise, open-clockwise; HOT valve: close-clockwise, open-counterclockwise.
11 SECURING HOSE CONNECTIONSPlace Clips (11A) onto End Bodies (11B).
12
13
14
11
4
ENGLISH
HOT COLD
CLOSED
OPEN
CLOSED
OPEN
11A
11B
11B
11A
12A12A 12A12A
12B
12B
12C12C
13A13A
13A13A
13B
13B
13D
13D
13C
13C
15 SECURING HANDLESBe sure Valves and Levers are in the "OFF" position. Secure handles by holding the Lever (15B) in place and tighten the Hubs (15A) by rotating them in a clockwise direction. To remove handles, rotate Hubs (15A) in a counterclockwise direction.
16 WATER SUPPLY CONNECTIONSConnect water Supply Lines (16A) to Faucet Inlets (16B). (Supply lines and fi ttings are not included.)
17 POP-UP PREPARATIONRemove Flange (17A) and unscrew Nut (17C) from the Pop-Up Drain Body (17B). Retain the Packing Ring (17D) inside the Ball Rod Opening (17E). 17E). 17ETake off the Spring Clip (17F) from the Ball Rod (17F) from the Ball Rod (17F 17G). Place the Nut (17C) on the Ball Rod (17G). Remove Locknut (17H), Friction Washer (17J), Rubber Washer (17K) and Stopper (17K) and Stopper (17K 17L) from Flange (17A).
POP-UP DRAIN BODY INSTALLATION STEPS
18 POP-UP INSTALLATIONApply a small bead of putty underneath the Flange (18A) and place a ring of putty around Drain Opening (18B) of sink. Use PTFE plumber’s tape to all threaded fi ttings according to manufacturer’s instructions. Insert Flange (18A) into Drain Opening (18B). From underneath, insert Rubber Washer (18C) and Friction Washer (18D) through the bottom of Flange (18A). Thread Locknut (18E) until Rubber Washer (18E) until Rubber Washer (18E 18C) seats securely inside Drain Opening (18B). Thread Drain Body (18F) to bottom of Flange (18F) to bottom of Flange (18F 18A). Hand tighten and adjust the Drain Body so that the Ball Rod Opening (18G) faces the rear. Wrench tighten Locknut (18E) and wipe excess putty. 18E) and wipe excess putty. 18E
18 BALLROD ADJUSTMENTDrop the Stopper (19A) into Drain Body (19B) from the top with the Off-Set (19C) facing rear. From below, insert the Ball Rod (19D) into the Ball Rod Opening (19E) through the Stopper Hole (19E) through the Stopper Hole (19E 19F) and secure with Nut (19F) and secure with Nut (19F 19G).
15
16
17
18
19
5
ENGLISH
16A16A
15B
15A15A
16B
17C
17A17A
17B
17D17E
17F
17G
17K 17H17A17A
17L 17B17G
17J
17C
18A18A
18C18D
18E
18F 18G
18B
19A19A
19B
19C
19E
19D19F
19D
19G
20 POP-UP ROD LINKAGE & ADJUSTMENTPlace one end of Spring Clip (20C) on end of Ball Rod (20B). Insert Ball Rod (20B) across and through hole in Pop-Up Strap (20D). Secure other end of Spring Clip (20C). Insert bottom of Lift Rod (20A) into hole at top of Pop-Up Strap (20D) . Tighten with Thumb Screw (20E) . Adjust Lif t Rod (20A) height by using the Thumb Screw (20E) on the Strap (20D) or by adjust ing the hole in which Bal l Rod (20B) goes through the Pop-Up Strap (20D). Be sure to leave enough space between Lift Rod Knob (20F) and Faucet (20F) and Faucet (20F 20G) when Lift Rod is down.
21 UNIT START UPTurn on hot and cold water supplies, and check for leaks above and below the sink.
22 FLUSHING & AERATOR CLEANINGTo prevent damage to the internal parts of your faucet from debris that may have collected in the water lines, please follow these steps: 1. Turn on water supply valves. 2. After connections have been made, remove Aerator (22A) and turn Handles
to the full “ON” position. 3. Check for leaks, retighten where necessary, and let lines fl ush for one minute
without moving faucet handles. This will remove debris from lines which can damage internal parts of faucet and cause leaks.
4. After fl ushing, turn off handles and replace Aerator (22A).
To clean aerator, lift out Washer (22B) and Insert (22C) from Aerator Head (22D). Rinse parts and replace.
23 VALVE CARTRIDGE MAINTENANCETurn off water supplies and relieve pressure before working on your faucet (see step 2). Remove Handles (23A) (see step 15), Valve Adapter (23B) (see step 12), unscrew Cartridge Assembly (23C) and inspect. Replace parts as necessary.
MAINTENANCE & CARE
2220
23
21
6
ENGLISH
20A20A
22A22A
20C
20B20D
20E
20F
20G
22B
22C
22D
23A23A
23B
23C
20B20C
20E
20A20A
20D
1-800-PFAUCET (1-800-732-8238)For Toll-Free Pfaucet information call 1-800-PFAUCET (1-800-732-8238) or visit www.pricepfi ster.com
• Installation Support• Care and Warranty Information
CAUTION: MaintenanceDISASSEMBLY1. Replacement parts may be available at the store where you
purchased your faucet.2. When replacement parts are not available, please write or
call Price Pfi ster Consumer Service.3. Always turn off water and relieve pressure before
working on your faucet.
NOTE: Trim CareCleaning Instructions:For all handles and decorative fi nishes, use only a soft damp cloth to clean and shine. Use of polish, detergents, abrasive cleaners, organic solvents, or acid may cause damage. Use of other than a soft damp cloth will nullify our warranty!Special Trim: Trim products which contain porcelain or other similar substances are not acceptable for public areas or commercial use. Installation of said trim is at user’s risk!
24 HOSE CONNECTION MAINTENANCETo detach Hose Assembly (24A), remove Clips (24B) from End Valve (24C) and pull the End Connectors (24D) from End Valves (24C). Remove Center Connector (24E) by pushing up on Quick Connect Housing (24E) by pushing up on Quick Connect Housing (24E 24F). Holding gray 24F). Holding gray 24Fplastic Collet (24G) in place, pull down on Quick Connect Housing (24F) until 24F) until 24FTube (24H) is free.
24
7
ENGLISH
24C
24B
24B
24G
24C
24E
24F
24D
24D
24A24A
24F24H
19701 DaVinciLake Forest, CA 92610Phone: 1-800-Pfaucetwww.pricepfi ster.com
A COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANYA COMPANY
49-N SeriesSerie 49-NSérie 49-N
EnglishEnglish EspañolEspañol FrançaisFrançais
** La Letra Indica el TerminadoLa Letra Indica el Terminado La Lettre Designe La FiniLa Lettre Designe La Fini
A Polished Chrome Cromo Pulido Chrome PoliJ Brushed Nickel PVD Niquel Cepillado PVD Nickel Brosse PVD
920-051*
910-024HotCalienteChaud910-025ColdFríoFroid
900-023Hot
CalienteChaud
900-024ColdFríoFroid
941-106*
931-009
941-107*
949-003
962-001
931-017
940-083*
971-005
931-030
970-019
972-019*