44” 3-in-1 console (xl-2) - whalen style … · 44” 3-in-1 console (xl-2) this item is designed...

Whalen Furniture Mfg. Inc. Factory No. 33-10944

44” 3-in-1 Console (XL-2)

This item is designed to be 3-in-1 configuration. Please choose which of the 3 options suits your needs. DO NOT discard any of the hardware or parts that you will not use on your set option, this will give you the opportunity to use this TV Console for different configurations in case you decide to upgrade your TV set in the future.

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if you are missing parts, do not return this item to the Retailer Store. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday ONLINE: www.whalenfurniture.com EMAIL: [email protected]

Video Instruction Guides Go to http://whalen.showuhow.com to view step-by-step instructional videos for assembling and installing your product. Enter the following product number on the ShowUhow homepage.

LOT NUMBER: DATE PURCHASED: / /

XL-2

Option 1 With Swinging Floater

http://www.whalenfurniture.com/

mailto:[email protected]

http://whalen.showuhow.com/

Model # XL-2

Please call for replacement parts or assistance: 1-866-942-5362


THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

MANUFACTURER: Whalen Furniture CATALOG: 44” 3-in-1 Console (XL-2) DATE OF MANUFACTURE: July, 2010 MADE IN CHINA

FITS UP TO MOST 50” FLAT PANEL TV’S MAXIMUM LOAD 135 lb. (61.2 kg)

FITS UP TO MOST 50” FLAT PANEL TV’S WITHOUT SWIVELING BRACKET MAXIMUM LOAD 135 lb. (61.2 kg)

MAXIMUM LOAD 50 lb. (22.7 kg)

1. Please read the Assembly Instructions prior to assembling this product. 2. Remove all hardware from box and sort by size. 3. Check to see that all hardware and parts are present BEFORE assembling. 4. Ask a friend to assist you with the assembly of this furniture. 5. To avoid damage, assemble the product on a sturdy, level and protective surface. 6. Please wait until all steps are completed before tightening bolts. 7. Make sure all bolts are tightly fastened before the unit is used.

THIS UNIT IS INTENDED FOR USE ONLY WITH THE PRODUCTS

AND MAXIMUM WEIGHTS INDICATED. USE WITH OTHER PRODUCTS OR PRODUCTS

HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY

CAUSING POSSIBLE INJURY. THE BASE OF THE TELEVISION MUST BE PLACED

SQUARELY IN THE CENTER OF THE STAND WITH NO OVERHANGING ON EITHER SIDE.

IMPORT AN T I NFORM ATION

GENER AL IN FORM ATION, T I PS & TRICK S

This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint Hardware between the wall and the TV stand to prevent any accidents or damages. When properly installed, this restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

Model # XL-2



Parts and Hardware Master List

Please read completely through the instructions and verify that all parts listed are present before beginning assembly.

A-Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)

D- Long Spine (1) D1- Short Spine (1) E- Left “L” Shape Leg (1)

F- Left Front Leg (1) G- Right “L” Shape Leg (1) H- Right Front Leg (1)

I- Top Glass Shelf (1) J- Middle Glass Shelf (1) K- Bottom Glass Shelf (1)

L- Swiveling Bracket (1) M- XYZ Mounting Frame (1) N- Monitor Bracket (2)

O- Safety Bar (1) P- Decorative Rail (2)

Model # XL-2



Parts and Hardware Master List

(1) - Suction Cup (2) - 3/4” Bolt (3) - 1 1/4” Bolt (4) - Hex Nut (20+1 extra) (18+1 extra) (16+1 extra) (4+1 extra)

(5) -Black Lock Washer (6) - Zinc Lock Washer (7) – Black Flat Washer (8) - Zinc Flat Washer (14+1 extra) (14+1 extra) (18+1 extra) (14+1 extra)

(9)- Large Flat Washer (10) - 2 1/2” Lag Bolt (11) - Concrete Anchor (12) - Cable Control (6) (6) (6) (2)

(13) - 1” Bolt Open Wrench Allen Wrench Tipping Restraint Hardware Kit (1)

(4+1 extra) (1) (1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 X 12 Bolt (4) M5 x 30 Bolt (4)

M6 x12 Bolt (4) M6 x 35 Bolt (4) M8x16 Bolt (4) M8 x40 Bolt (4)

M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)

Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)

Tools required: Allen Wrench (provided) and Open Wrench (provided), Phillips Head Screwdriver, Mallet, Power Drill, 3/8” & 3/16”Drill Bit, Socket Wrench Adapter with Socket Set, 1/2” Masonry Bit for brick concrete, Stud Sensor.

Model # XL-2



Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make it easier during assembly of unit.

1. Unpack the unit and confirm that you have all the hardware and required parts listed. 2. Align the bottom bracket holes of Left “L” Shape Leg (E) with the sockets on the Left Front

Leg (F). Make sure the upper tube of “L” Shape Leg fits into the cutout of Left Front Leg properly. Attach in place by inserting two 3/4” Bolts (2) with Black Washers (5 & 7) into the bracket holes. Tighten the bolts with Allen Wrench provided. See detail #1.

3. Repeat last step to combine the Right “L” Shape Leg (G) with Right Front Leg (H) together. 4. Attach 2 Decorative Rails (P) to the bottom of Long Spine (D) using six 1 1/4” Bolts (3).

Tighten with Allen Wrench provided. See detail #1A.

Required hardware in this step

Description: (2) – 3/4” Bolt (3) – 1 1/4” Bolt (5) – Black Lock Washer (7) – Black Flat Washer

Sketch Qty. (4 pcs) (6 pcs) (4 pcs) (4 pcs)

Tools required: Allen Wrench

Ass embl y Ins t ruc t ions for Opt ion #1 :

Conso le w i th Sw inging F loa ter

Model # XL-2



Assembly Instructions for Console with Swinging Floater

5. Locate the Long Spine (D) on a scratch free surface with 2 round holes facing up as shown in detail #2.

6. Align the holes on back rail of 3 Shelf Frames (A, B & C) with the sockets on the Long Spine (D). Insert and screw 1 1/4” Bolts (3) with Zinc Lock Washers & Flat Washers (6 & 8) through the pre-drilled holes on back rail into the Spine. Make sure the corner plates for Suction Cup on each Shelf Frame will face up after assembly. See detail #2.

Required hardware in this step Description: (3) – 1 1/4” Bolt (6) – Zinc Lock Washer (8) – Zinc Flat Washer

Sketch Qty. (6 pcs) (6 pcs) (6 pcs)


Model # XL-2




7. Stand the unit upright. 8. Align and attach Left Leg Assembly to the Top Shelf Frame (A) using two 1” Bolts (13) with

Zinc Washers (6 & 8) through the pre-drilled holes on inner side rail into the top of both Legs. See detail #3. DO NOT tighten the bolts.

9. Secure Left Leg Assembly to Middle & Bottom Shelf Frame (B & C) using the 1 1/4” Bolts (3) with Zinc Washers (6 & 8) from inside the shelf frame into the sockets included on the side of Legs. See detail #3A.

10. Repeat last 2 steps to attach Right Leg Assembly at the other end.

Required hardware in this step Description: (13)- 1” Bolt (3) – 1 1/4” Bolt (6) – Zinc Lock Washer (8) – Zinc Flat Washer



Model # XL-2




11. Go back and tighten all bolts with Allen Wrench provided.

12. In case of uneven floor, Floor Levelers are provided at the bottom of both Front Legs (F & H). Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in detail #4.

Hardware provided Tools required

Pre-attached Floor Leveler No tool required

Model # XL-2




13. Align and attach Swiveling Bracket (L) to the top of Long Spine (D) using six 3/4” Bolts (2)

with Black Washers (5 & 7). Make sure the swivel bolt head is up. See detail #5. Note: The Spine can provide four height options for your TV set. Refer to your TV size, adjust the Swiveling Bracket at your desired height to offer optimum viewing.


Description: (2) - 3/4” Bolt (5) – Black Lock Washer (7) – Black Flat Washer



Model # XL-2




14. Hold the flat side of XYZ Mounting Frame (M) onto the Swiveling Bracket (L) ensuring the hook on the side of Mounting Frame is bottom. Align and attach by threading four 3/4” Bolts (2) with Black Flat Washers (7) through the metal plate on XYZ Mounting Frame and the Swiveling Bracket, at the other side of Swiveling Bracket place the other Black Flat Washers (7) and Black Lock Washers (5), and then secure with Hex Nuts (4). Securely tighten with Open Wrench and Allen Wrench provided. See detail #6.


Description: (2) - 3/4” Bolt (4) - Hex Nut (5) – Black Lock Washer (7) -Black Flat Washer


Tools required: Allen Wrench and Open Wrench

Model # XL-2



Mounting Monitor Bracket to a television with a flat back

Note: For televisions with a curved back or recessed back proceed directly to step #18.

15. Determine the correct diameter of the bolt your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If you are unable to find the correct bolt consult a local hardware store.

16. Once you have determined the correct diameter Bolt, follow the appropriate Diagram below, thread the Short Bolt through the appropriate Lock Washer, Flat Washer, the Monitor Bracket (N), and into the upper threaded inserts of TV. As shown in detail #7A. Note: Lean the TV up against a wall or other solid surface when attaching with the Monitor Brackets (N). DO NOT place the TV face down on the glass this may cause permanent damage.

17. Proceed to insert the long Bolt through the appropriate Lock Washer, the Flat Washer, the slot of Monitor Bracket (N), a second Flat Washer (M4/M5 Diameter Bolts only), appropriate Spacer, and into the bottom threaded inserts of TV. As shown in detail #7. Make sure the Monitor Brackets (N) are centered and level with each other. Tighten the bolts securing the Monitor Brackets to the TV.

Parts provided Qty. Tools required

N – Monitor Bracket (2) Phillips Screwdriver TV Mounting Kit

Model # XL-2



Mounting Monitor Bracket to a television with a curved / recess back

18. Determine the correct diameter of the bolt your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If you are unable to find the correct bolt consult a local hardware store.

19. Once you have determined the correct diameter Bolt, follow the appropriate Diagram below, thread the Bolt through the appropriate Lock Washer, the Large Flat Washer, the Monitor Bracket (N), a second Large Flat Washer (M4/M5 Diameter Bolts only), appropriate Spacer and into the threaded inserts of TV. See detail #8.

20. Make sure the Monitor Brackets (N) are vertically centered and level with each other. Tighten

the bolts to secure the Monitor Brackets to the TV.

Model # XL-2




MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGREE ANGLE PRIOR TO INSTALLATION OF TV.

21. Once the Monitor Brackets (N) are attached onto the back of television, ask for assistance to lift the television up to the XYZ Mounting Frame (M). Place the hooks on Monitor Brackets over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to center the television.

22. Insert the Safety Bar (O) into the bottom holes on the side of XYZ Mounting Frame (M) by sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into the slot of hook so that it is facing backward. Make sure it sits over the bottom hook of the Monitor Brackets. See detail #9.


O - Safety Bar (1) No tool required

Model # XL-2




23. Attach 2 Cable Controls (12) onto the backside of Spine (D) with the 3/4” Bolts (2). Tighten the bolts with Allen Wrench provided. See detail #10.

24. The Cable Controls (12) enable you to shorten, separate and route both single and bundled cables. Using the Cable Controls you can create a system for routing cables through channels, between components and to power sources without usual tangled mess or annoying signal interference. As shown in detail #10A.


Description: (2) - 3/4” Bolt (12) – Cable Control

Sketch

Qty. (4 pcs) (2 pcs)


Model # XL-2




25. Put Suction Cups (1) firmly into the top holes and corner plates on 3 Shelf Frames (A, B & C) as shown in detail #11.

26. Place Top Glass (I) and Glass Shelves (J & K) in place as shown in detail #11. Make sure the glass is properly centered and the black side of glass is down. Push each glass all the way back against the Spine. Also, be sure to press down evenly and firmly each glass onto the Suction Cups to make sure they securely rest onto the Suction Cups.

Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the glass shelf from falling and getting damage. If glass is scratched you can minimize the damage by using a BLACK marker and filling in scratched area from underneath.


Description Sketch Qty.

(1) – Suction Cup (20 pcs)

Model # XL-2



TIPPING RESTRAINT HARDWARE

Note: We have included one Tipping Restraint Hardware bag for this unit.

When properly installed, this restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a wall stud and your unit when installing.

Please carefully read the instructions printed on the plastic bag.

Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit.

Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

Model # XL-2



27. Align the bottom bracket holes of Left “L” Shape Leg (E) with the sockets on the Left Front Leg (F). Make sure the upper tube of “L” Shape Leg fits into the cutout of Left Front Leg properly. Attach in place by inserting two 3/4” Bolts (2) with Black Washers (5 & 7) into the bracket holes. Tighten the bolts with Allen Wrench provided. See detail #12.

28. Repeat last step to combine the Right “L” Shape Leg (G) with Right Front Leg (H) together.


Description: (2) - 3/4” Bolt (5) – Black Lock Washer (7) – Black Flat Washer



Assembly Instructions for Option #2 -3: Console w ith Universal Wal l Mount

Model # XL-2



Assembly Instructions for Table-top

29. Locate Short Spine (D1) on a scratch free surface with 2 round holes facing up as shown in detail #13.

30. Align the holes on back rail of 3 Shelf Frames (A, B & C) with the sockets on the Short Spine (D1). Insert and screw 1 1/4” Bolts (3) with Zinc Lock Washers & Flat Washers (6 & 8) through the pre-drilled holes on back rail into the Spine. Make sure the corner plates for Suction Cup on each Shelf Frame will face up after assembly. See detail #13.

Required hardware in this step Description: (3) – 1 1/4” Bolt (6) – Zinc Lock Washer (8) – Zinc Flat Washer



Model # XL-2




31. Stand the unit upright. 32. Align and attach Left Leg Assembly to the Top Shelf Frame (A) using two 1” Bolts (13) with

Zinc Washers (6 & 8) through the pre-drilled holes on inner side rail into the top of both Legs. See detail #14. DO NOT tighten the bolts.

33. Secure Left Leg Assembly to Middle & Bottom Shelf Frame (B & C) using the 1 1/4” Bolts (3) with Zinc Washers (6 & 8) from inside the shelf frame into the sockets included on the side of Legs. See detail #14A.

34. Repeat last 2 steps to attach Right Leg Assembly at the other end.

Required hardware in this step Description: (13)- 1” Bolt (3) – 1 1/4” Bolt (6) – Zinc Lock Washer (8) – Zinc Flat Washer



Model # XL-2




35. Go back and tighten all bolts with Allen Wrench provided.

36. In case of uneven floor, Floor Levelers are provided at the bottom of both Front Legs (F & H). Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in detail #15.

Hardware provided Tools required

Pre-attached Floor Leveler No tool required

Model # XL-2




37. Attach 2 Cable Controls (12) onto the backside of Spine (D1) with the 3/4” Bolts (2). Tighten the bolts with Allen Wrench provided. See detail #16.

38. The Cable Controls (12) enable you to shorten, separate and route both single and bundled cables. Using the Cable Controls you can create a system for routing cables through channels, between components and to power sources without usual tangled mess or annoying signal interference. As shown in detail #16.


Description: (2) - 3/4” Bolt (12) – Cable Control

Sketch

Qty. (4 pcs) (2 pcs)


Model # XL-2




39. Put Suction Cups (1) firmly into the top holes and corner plates on 3 Shelf Frames (A, B & C) as shown in detail #17.

40. Place Top Glass (I) and Glass Shelves (J & K) in place as shown in detail #17. Make sure the glass is properly centered and the black side of glass is down. Push each glass all the way back against the Spine. Also, be sure to press down evenly and firmly each glass onto the Suction Cups to make sure they securely rest onto the Suction Cups.

Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the glass shelf from falling and getting damage. If glass is scratched you can minimize the damage by using a BLACK marker and filling in scratched area from underneath.


Description Sketch Qty.

(1) – Suction Cup (20 pcs)

Model # XL-2




41. Position the assembled Table-top in your desired location against the wall. Now follow the instructions printed on the plastic bag in order to mount the Tipping Restraint Hardware Kit to the Spine properly. As shown in detail #18.

NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.

42. The Table-top is ready for use now if you only want to place the TV on the console top. Be sure to position your TV in center of console with no overhang on either side.

Model # XL-2



Assembly Instructions for Universal Wall Mount

Installing XYZ Mounting Frame onto WOODEN STUD WALL

43. The XYZ Mounting Frame (M) must be mounted to two Wood Studs at least 12” apart, using a high quality Stud Finder to locate the two adjacent studs. After you have located the studs, verify with a nail for added security. See detail #19A.

44. Pre-drill a 2 1/2" deep hole at the desired height in each stud using a 3/16” drill bit, make sure that the holes are centered in the studs and level with each other. Use the XYZ Mounting Frame (M) as a template to mark the corresponding location for the bottom holes in each stud, drill holes 2 1/2" deep with the 3/16” drill bit at the marked location.

45. Orient the Mounting Frame with the “C” plate against the wall, and using four Lag Bolts (10) with Large Flat Washer (9) through the slots of “C” Plate on Mounting Frame into the holes in the wall, secure the mounting frame to the wall as shown in detail #19B.

Hardware provided Sketch Qty.

(9) – Large Flat Washer (4)

(10) –2 1/2” Lag Bolt (4)

Tools required

Stud Sensor, Mallet, Power Drill, 3/16” Drill Bit, Socket Set

Do not over tighten the Lag Bolts. Tighten Lag Bolts only until the Lag Bolt Washer is pulled firmly against the “C” Plate of Mounting Frame. If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch in thickness. Failure to heed this caution may result property damage and/or personal injury.

The following steps are only for those who wish to mount their TV directly to the wall. If you have already mounted your TV to the Swinging Floater or plan to display your TV on the top

surface of the stand, disregard the following steps.

Model # XL-2



Assembly Instruction for installing XYZ Mounting Frame onto BRICK, SOLID CONCRETE OR CONCRETE BLOCK

46. Use the XYZ Mounting Frame (M) as a template, mark six holes location on the wall, three in the top row and three in the bottom row of slots. Make sure that the holes are level and there is at least 6” between any two holes, pre-drill these holes with a 1/2” masonry bit to at least 2 1/2” in depth.

47. Insert a Concrete Anchor (11) into each of these holes; make sure they are completely seated and flush with the concrete surface, even if there is a layer of drywall or other material in front of the concrete.

48. Attach the XYZ Mounting Frame (M) to the wall using six Lag Bolts (10) and Large Flat Washers (9) through the slot of “C” Plate on Mounting Frame into the Concrete Anchors (11) in the wall as shown in detail #20. Make sure the back hook of Mount Frame is bottom.

Concrete Anchors should only be used for masonry mounting. NEVER use the wall anchors to mount the unit to drywall.

Maximum weight 165 lb (74.8 kg)

Hardware provided Sketch Qty.

(9) – Large Flat Washer (6)

(10) – Lag Bolt (6)

(11) –Concrete Anchor (6)

Tools required: Mallet, Power Drill, 1/2” Masonry Bit for brick concrete, Socket Set

Model # XL-2



Assembly Instructions for Universal Wall Mount

49. Once the Monitor Brackets (N) are attached onto the back of television, ask for assistance to lift the television up to the XYZ Mounting Frame (M). Place the hooks on Monitor Brackets over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to center the television.

50. Insert the Safety Bar (O) into the bottom holes on the side of XYZ Mounting Frame (M) by sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into the slot of hook so that it is facing wall. Make sure it sits over the bottom hook of the Monitor Brackets. See detail #21.

51. Place assembled console under your TV set as shown in detail #21A.


O - Safety Bar (1) No tool required

Model # XL-2



Care and Maintenance

Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test in an

inconspicuous area first. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently.

Avoid rubbing. Always use protective pads under hot dishes and plates. Heat can cause chemical changes

that may create spotting within the furniture finish. Stains or marks from crayons or ink markers will be difficult to remove. In the event that your furniture is stained or otherwise damaged during use, we recommend

that you call a professional to repair your furniture. Check bolts/screws periodically and tighten them if necessary.

Further advice about wood furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Follow these important and helpful tips that will enhance your furniture as it ages.

We hope you enjoy your purchase for many years.

QUALITY GUARANTEE

We are confident that you will be delighted with your Whalen Furniture purchase. Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific legal rights and you may also have other rights which vary from State to State.

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m. PST, Monday to Friday

www.whalenfurniture.com

http://www.whalenfurniture.com/

IF Y

OU

RE

QU

IRE

D T

O O

RD

ER

PA

RT

S P

LE

AS

E U

SE

TH

E L

IST

BE

LO

W

44" 3

-in-1

Co

ns

ole

(XL

-2)

*XL-2

-1-L

SLong S

pin

e*X

L-2

-19-Z

FW

Zin

c F

lat W

asher

*XL-2

-38-M

5x12B

M5 x

12 B

olt

*XL-2

-2-T

SF

Top S

helf F

ram

e*X

L-2

-20-L

FW

Larg

e F

lat W

asher

*XL-2

-39-M

5x30B

M5 x

30 B

olt

*XL-2

-3-M

SF

Mid

dle

Shelf F

ram

e*X

L-2

-21-2

1/2

LB

2 1

/2" L

ag B

olt

*XL-2

-40-M

6x12B

M6 x

12 B

olt

*XL-2

-4-B

SF

Botto

m S

helf F

ram

e*X

L-2

-22-1

3/4

CA

1 3

/4" C

oncre

te A

nchor

*XL-2

-41-M

6x35B

M6 x

35 B

olt

*XL-2

-5-L

FL

Left F

ront L

eg

*XL-2

-23-H

NH

ex N

ut

*XL-2

-42-M

8x16B

M8 x

16 B

olt

*XL-2

-6-L

LS

LLeft "L

" Shape L

eg

*XL-2

-24-O

WO

pen W

rench

*XL-2

-43-M

8x40B

M8 x

40 B

olt

*XL-2

-7-R

FL

Rig

ht F

ront L

eg

*XL-2

-25-A

WA

llen W

rench

*XL-2

-44-T

RH

KT

ippin

g R

estra

int H

ard

ware

Kit

*XL-2

-8-R

LS

LR

ight "L

" Shape L

eg

*XL-2

-26-S

CS

uctio

n C

up

*XL-2

-45-F

LF

loor L

evele

r

*XL-2

-9-D

RD

ecora

tive R

ail

*XL-2

-27-C

CC

able

Contro

l*X

L-2

-46-R

PG

Round P

lastic

Gro

mm

et

*XL-2

-10-T

GS

Top G

lass S

helf

*XL-2

-28-S

SS

mall S

pacer

*XL-2

-47-O

PG

Oval P

lastic

Gro

mm

et

*XL-2

-11-M

GS

Mid

dle

Gla

ss S

helf

*XL-2

-29-L

SLarg

e S

pacer

*XL-2

-48-P

EC

Pla

stic

End C

ap (2

0x40)

*XL-2

-12-B

GS

Botto

m G

lass S

helf

*XL-2

-30-M

4M

5F

WM

4/M

5 F

lat W

asher

*XL-2

-49-P

CP

lastic

Cover

*XL-2

-13-C

HC

om

ple

te H

ard

ware

*XL-2

-31-M

6M

8F

WM

6/M

8 F

lat W

asher

*XL-2

-50-M

FX

YZ

Mountin

g F

ram

e

*XL-2

-14-3

/4B

3/4

” Bolt

*XL-2

-32-M

4LW

M4 L

ock W

asher

*XL-2

-51-M

BM

onito

r Bra

cket

*XL-2

-15-1

1/4

B1 1

/4” B

olt

*XL-2

-33-M

5LW

M5 L

ock W

asher

*XL-2

-52-S

BS

wiv

elin

g B

racket

*XL-2

-16-B

LW

Bla

ck L

ock W

asher

*XL-2

-34-M

6LW

M6 L

ock W

asher

*XL-2

-53-S

BS

afe

ty B

ar

*XL-2

-17-Z

LW

Zin

c L

ock W

asher

*XL-2

-35-M

8LW

M8 L

ock W

asher

*XL-2

-54-S

SS

hort S

pin

e

*XL-2

-18-B

FW

Bla

ck F

lat W

asher

*XL-2

-36-M

4x12B

M4 x

12 B

olt

*XL-2

-55-S

EC

Spin

e E

nd C

ap (4

0x80)

*XL-2

-37-M

4x30B

M4 x

30 B

olt

*XL-2

-56-1

B1” B

olt

44” 3-in-1 console (xl-2) - whalen style … · 44” 3-in-1 console (xl-2) this item is designed...

Documents