Sanken General Purpose Inverter

400 V class : IHF 1.5kW~250kWIPF 7.5kW~315kW

Sanken General Purpose Inverter

SAMCO-i SERIES

Upgraded Functions and Performance!

Optimum Model Selection Reduces Costs

1

•Optimum Model SelectionTwo models are availabe to withstand different overloads. The allowable overload capacity is 150%for the IHF model and 120% for the IPF model. Select the IHF model for quick acceleration ordeceleration and the IPF model for greater motor output.

•Sensorless Vector ControlIn addition to V/f control, the SAMCO-i general purpose inverter supports sensor-less control toenhance speed control and load responsiveness. Even when the inverter is used with a non-standard motor, the auto tuning function automatically measures the motor constants necessary forSensorless Vector Control and controls the speed accordingly.

•Energy-Saving ControlThe SAMCO-i general purpose inverter operates in three energy-saving modes. Selecting theoptimum mode greatly reduces energy consumption.

•High-Grade Flying Start Function(with a Revolution Direction Detection Function)The conventional inverter sometimes tripped the motor due to an overcurrent in a sudden free-runstart. However, the SAMCO-i general purpose inverter provides a smooth start by detecting therevolution speed and direction of the motor. For example, the general purpose inverter can stop themotor of a fan without shock for a smooth flying start in a specified direction even when a headwindis turning the motor in the reverse direction.

•PID FunctionThe standard PID function simplifies system design.

•Momentary Voltage Drop Compensation FunctionIn case of a momentary voltage drop or power failure, the momentary voltage drop compensationfunction allows a motor to run continuously with minimum tripping by using the inertia of the motoror load.

•Good Acceleration/Deceleration CharacteristicsThe DSAMCO-i general purpose inverter provides smooth and powerful acceleration anddeceleration.

•Wide Lineup of Optional BoardsThe optional water supply, PG support, and serial communication boards can be used to upgradethe performance and functions of the SAMCO-i general purpose inverter.

0 800ms

■Speed step response

Motor primary current

Motor speed

Speed estimated value

Torque

■Load step response

0f=20→25Hz step

0

600

4000 (ms/div)

Motor speed command 125 (rpm/div)

Motor speed 125 (rpm/div)

Motor primary current 5 (A/div)

Sanken General Purpose Inverter

2

Sanken General Purpose Inverter

Model

Applicable motor capacity

Digital

Analog

Digital

Analog

Rated capacity

Rated current

Rated overload current capacity

Rated voltage/frequency

Power supply

Allowable fluctuation

Allowable momentary voltage drop

　

Control method

Modulation method

Setting frequency range

Frequency

setting resolution

Frequency accuracy

Voltage/frequency (V/f)

Torque boost

Acceleration/deceleration time

DC braking

Additional functions

Frequency

setting

Input signals

Output

signals

　　　　　LED display

Protective functions

Ambient temperature

Ambient humidity

Operating environment

IHF-1.5K

1.5kW

2.8kVA

4.0A

IHF-2.2K

2.2kW

4.2kVA

6.0A

IHF-4.0K

4.0kW

6.2kVA

9.0A

IHF-5.5K

5.5kW

9.0kVA

13A

IHF-7.5K

7.5kW

12kVA

17A

IHF-11K

11kW

17kVA

25A

IHF-15K

15kW

22kVA

32A

Output

InputC

ontrol functionsO

perational functionsEnvironm

ental

　conditions

Protective structure

Cooling method

Mass (Approx.)

Digital

Analog

Contact output

Open collector output

150% for 1 minute

3Φ 380V/50Hz, 400V/50Hz, 460V/60Hz

3Φ 380V to 460V

Voltage: -15%, +10% Frequency: ±5%

320V and above: Continuous operation (short-time rating) Below 320V: 15msec operation

Totally enclosed type (IP20)

Forced air cooling

V/f control or Sensorless Vector Control

Sinusoidal PWM

0.2Hz to 400Hz (starting frequency of 0.2Hz to 20Hz possible)

0.01Hz(0.05Hz to 120Hz)

0.1% (10-bit 0 to 10V, 4 to 20mA), 0.2% (9-bit 0 to 5V) at maximum output frequency

±0.01% of output frequency (at -10℃ to +50℃)

±0.2% of maximum output frequency (at 25 ± 10)

0 to 10%

Starting frequency (0.5Hz to 20Hz), braking time (0.1sec to 10 sec), braking force (1 to 10 steps)

Operation panel

0 to 5V, 0 to 10V, 4 to 20mA or variable resistor (5kΩ)

Alarm batch (1C contact 250VAC, 0.3A)

Operation, frequency coincidence, overload warning, undervoltage, frequency reach

Frequency, output current, synchronous rotation, line speed (free unit), alarms, charging indicator for capacitor

-10℃ to +50℃

Below 90% (no condensation allowed)

Indoors at an altitude below 1,000m (Do not expose to direct sunlight, or subject to corrosive or flammable gas, oil mist or dust.)

3kg 5kg 10kg

※1：Rated capacity: Capacity at an output voltage of 400V※2：Setting frequency range for Sensorless Vector Control: 1Hz to 120Hz※3：Maximum output frequency: Frequency at 5V, 10V, 20mA※4：Acceleration/deceleration time: Time from 0 to the reference acceleration/deceleration frequency.※5：V/f mode: From 0.1 seconds.

※1

※4

※3

※5

※2

Flying start, acceleration/deceleration stall prevention, momentary voltage drop compensation, multiple speed operation, frequency jump, restart after momentary power break, automatic alarm reset, energy-saving operation, pattern operation, PID control operation, torque limiter (only sensorless vector)

0 to 6,500 sec. (independent setting of acceleration/deceleration time possible) Linear or programmable S-curve can be selected.

Frequency command, forward command, reverse command, frequency setting selection, acceleration/deceleration time selection, free-run stop/alarm reset, emergency stop, multiple speed, jogging selection, step frequency selection, operation signal holding, torque limiter (only sensorlessvector)

Any base frequency setting between 30Hz and 400Hz can be set. (Constant torque and reduced torque pattern can be selected.)

Current limit, overcurrent shutdown, motor overload, external thermal protection, undervoltage, momentary power break, overvoltage, cooling fin overheat, output open-phase

※3

SAMCO-ihF (1.5kW~15kW)

S P E C I F I C A T I O N S

3

Standard Specifications

Model

Applicable motor capacity

Digital

Analog

Digital

Analog

Rated capacity

Rated current

Rated overload current capacity

Rated voltage/frequency

Power supply

Allowable fluctuation

Allowable momentary voltage drop

　

Control method

Modulation method

Setting frequency range

Frequency

setting resolution

Frequency accuracy

Voltage/frequency (V/f)

Torque boost

Acceleration/deceleration time

DC braking

Additional functions

Frequency

setting

Input signals

Output

signals

　　　　LED display

Protective functions

Ambient temperature

Ambient humidity

Operating environment

IHF-18.5K

18.5kW

27kVA

39A

IHF-22K

22kW

32kVA

46A

IHF-30K

30kW

43kVA

62A

IHF-37K

37kW

51kVA

74A

IHF-45K

45kW

62kVA

90A

IHF-55K

55kW

76kVA

110A

Output

InputC

ontrol functionsO

perational functionsEnvironm

ental

　conditions

Protective structure

Cooling method

Mass (Approx.)

Digital

Analog

Contact output

Open collector output

150% for 1 minute

3Φ 380V/50Hz, 400V/50Hz, 460V/60Hz

3Φ 380V to 460V

Voltage: -15%, +10% Frequency: ±5%

320V and above: Continuous operation (short-time rating) Below 320V: 15msec operation

Totally enclosed type (IP20)

Forced air cooling

V/f control or Sensorless Vector Control

Sinusoidal PWM

0.2Hz to 400Hz (starting frequency of 0.2Hz to 20Hz possible)

0.01Hz(0.05Hz to 120Hz)

0.1% (10-bit 0 to 10V, 4 to 20mA), 0.2% (9-bit 0 to 5V) at maximum output frequency

±0.01% of output frequency (at -10℃ to +50℃)

±0.2% of maximum output frequency (at 25 ±10℃)

0 to 10%

Starting frequency (0.5Hz to 20Hz), braking time (0.1sec to 10 sec), braking force (1 to 10 steps)

Operation panel

0 to 5V, 0 to 10V, 4 to 20mA or variable resistor (5kΩ)

Alarm batch (1C contact 250VAC, 0.3A)

Operation, frequency coincidence, overload warning, undervoltage, frequency reach

Frequency, output current, synchronous rotation, line speed (free unit), alarms, charging indicator for capacitor

-10℃ to +50℃

Below 90% (no condensation allowed)

Indoors at an altitude below 1,000m (Do not expose to direct sunlight, or subject to corrosive or flammable gas, oil mist or dust.)

17kg 29kg 39kg

※1：Rated capacity: Capacity at an output voltage of 400V※2：Setting frequency range for Sensorless Vector Control: 1Hz to 120Hz※3：Maximum output frequency: Frequency at 5V, 10V, 20mA※4：Acceleration/deceleration time: Time from 0 to the reference acceleration/deceleration frequency.※5：V/f mode: From 0.1 seconds.

※1

※4

※3

※5

※2

Flying start, acceleration/deceleration stall prevention, momentary voltage drop compensation, multiple speed operation, frequency jump, restart after momentary power break, automatic alarm reset, energy-saving operation, pattern operation, PID control operation, torque limiter (only sensorless vector)

0 to 6,500 sec. (independent setting of acceleration/deceleration time possible) Linear or programmable S-curve can be selected.

Frequency command, forward command, reverse command, frequency setting selection, acceleration/deceleration time selection, free-run stop/alarm reset, emergency stop, multiple speed, jogging selection, step frequency selection, operation signal holding, torque limiter (only sensorless vector)

Any base frequency setting between 30Hz and 400Hz can be set. (Constant torque and reduced torque pattern can be selected.)

Current limit, overcurrent shutdown, motor overload, external thermal protection, undervoltage, momentary power break, overvoltage, cooling fin overheat, output open-phase

※3

SAMCO-ihF (18.5kW~55kW)

Sanken General Purpose Inverter

S P E C I F I C A T I O N S

4

Standard Specifications

Sanken General Purpose Inverter

Model

Applicable motor capacity

Digital

Analog

Digital

Analog

Rated capacity

Rated current

Rated overload current capacity

Rated voltage/frequency

Power supply

Allowable fluctuation

Allowable momentary voltage drop

　

Control method

Modulation method

Setting frequency range

Frequency

setting resolution

Frequency accuracy

Voltage/frequency (V/f)

Torque boost

Acceleration/deceleration time

DC braking

Additional functions

Frequency

setting

Input signals

Output

signals

　�

　　　　　LED display

Protective functions

Ambient temperature

Ambient humidity

Operating environment

IHF-75K

75kW

102kVA

147A

IHF-90K

90kW

120kVA

173A

IHF-110K

110kW

146kVA

211A

IHF-132K

132kW

175kVA

253A

IHF-160K

160kW

211kVA

304A

IHF-220K

220kW

295kVA

426A

IHF-250K

250kW

327VA

472A

Output

InputC

ontrol functionsO

perational functionsEnvironm

ental

　conditions

Protective structure

Cooling method

Mass (Approx.)

Digital

Analog

Contact output

Open collector output

Analog output

150% for 1 minute

3Φ 380V/50Hz, 400V/50Hz, 460V/60Hz

3Φ 380V to 460V

Voltage: -15%, +10% Frequency: ±5%

320V and above: Continuous operation (short-time rating) Below 320V: 15msec operation

Totally enclosed type (IP20)

Forced air cooling

V/f control or Sensorless Vector Control

Sinusoidal PWM

0.05Hz to 400Hz (starting frequency of 0.05Hz to 20Hz possible)

0.01Hz(0.05Hz to 120Hz)

0.1% (10-bit 0 to 10V, 4 to 20mA), 0.2% (9-bit 0 to 5V) at maximum output frequency

±0.01% of output frequency (at -10℃ to +50℃)

±0.2% of maximum output frequency (at 25 ± 10℃)

0 to 10%

Starting frequency (0.5Hz to 20Hz), braking time (0.1sec to 10 sec), braking force (1 to 10 steps)

Operation panel

0 to 5V, 0 to 10V, 4 to 20mA or variable resistor (5kΩ)

Alarm batch (1C contact 250VAC, 0.3A)

Operation, frequency coincidence, overload warning, undervoltage, frequency reach

Select from setting frequency, output frequency, output current, DC current, heater temperature, load rate, analog input (VRF, IRF)

Frequency, output current, synchronous rotation, line speed (free unit), alarms, charging indicator for capacitor

-10℃ to +50℃

Below 90% (no condensation allowed)

Indoors at an altitude below 1,000m (Do not expose to direct sunlight, or subject to corrosive or flammable gas, oil mist or dust.)

70kg65kg 110kg 160kg 280kg155kg

※1：Rated capacity: Capacity at an output voltage of 400V※2：Setting frequency range for Sensorless Vector Control: 5Hz to 120Hz for rated frequency 1, 1Hz to 120Hz for rated frequency 2※3：Maximum output frequency: Frequency at 5V, 10V, 20mA※4：Acceleration/deceleration time: Time from 0 to the reference acceleration/deceleration frequency.※5：V/f mode: From 0.1 seconds.

※1

※4

※5

※5

※2

Flying start, acceleration/deceleration stall prevention, momentary voltage drop compensation, multiple speed operation, frequency jump, restart after momentary power break, automatic alarm reset, energy-saving operation, pattern operation, PID control operation, torque limiter (only sensorless vector)

0 to 6,500 sec. (independent setting of acceleration/deceleration time possible) Linear or programmable S-curve can be selected.

Frequency command, forward command, reverse command, frequency setting selection, acceleration/deceleration time selection, free-run stop/alarm reset, emergency stop, multiple speed, jogging selection, step frequency selection, operation signal holding, torque limiter (only sensorless vector)

Any base frequency setting between 30Hz and 400Hz can be set. (Constant torque and reduced torque pattern can be selected.)

Current limit, overcurrent shutdown, motor overload, external thermal protection, undervoltage, momentary power break, overvoltage, cooling fin overheat, output open-phase

※3

SAMCO-ihF (75kW~250kW)

S P E C I F I C A T I O N S

5

Standard Specifications

SAMCO-ipF (7.5kW~55kW)

Sanken General Purpose Inverter

Model

Applicable motor capacity

Digital

Analog

Digital

Analog

Rated capacity

Rated current

Rated overload current capacity

Rated voltage/frequency

Power supply

Allowable fluctuation

Allowable momentary voltage drop

　

Control method

Modulation method

Setting frequency range

Frequency

setting resolution

Frequency accuracy

Voltage/frequency (V/f)

Torque boost

Acceleration/deceleration time

DC braking

Additional functions

Frequency

setting

Input signals

Output

signals

　　　　　LED display

Protective functions

Ambient temperature

Ambient humidity

Operating environment

IPF-7.5K

7.5kW

12kVA

17A

IPF-11K

11kW

17kVA

25A

IPF-15K

15kW

22kVA

32A

IPF-22K

22kW

32kVA

46A

IPF-18.5K

18.5kW

27kVA

39A

IPF-30K

30kW

43kVA

62A

IPF-37K

37kW

51kVA

74A

IPF-55K

55kW

76kVA

110A

IPF-45K

45kW

62kVA

90A

Output

InputC

ontrol functionsO

perational functionsEnvironm

ental

　conditions

Protective structure

Cooling method

Mass (Approx.)

Digital

Analog

Contact output

Open collector output

120% for 1 minute

3Φ 380V/50Hz, 400V/50Hz, 460V/60Hz

3Φ 380V to 460V

Voltage: -15%, +10% Frequency: ±5%

320V and above: Continuous operation (short-time rating) Below 320V: 15msec operation

Totally enclosed type (IP20)

Forced air cooling

V/f control or Sensorless Vector Control

Sinusoidal PWM

0.2Hz to 400Hz (starting frequency of 0.2Hz to 20Hz possible)

0.01Hz(0.05Hz to 120Hz)

0.1% (10-bit 0 to 10V, 4 to 20mA), 0.2% (9-bit 0 to 5V) at maximum output frequency

±0.01% of output frequency (at -10℃ to +50℃)

±0.2% of maximum output frequency (at 25 ±10℃)

0 to 10%

Starting frequency (0.5Hz to 20Hz), braking time (0.1sec to 10 sec), braking force (1 to 10 steps)

Operation panel

0 to 5V, 0 to 10V, 4 to 20mA or variable resistor (5kΩ)

Alarm batch (1C contact 250VAC, 0.3A)

Operation, frequency coincidence, overload warning, undervoltage, frequency reach

Frequency, output current, synchronous rotation, line speed (free unit), alarms, charging indicator for capacitor

-10℃ to +50℃

Below 90% (no condensation allowed)

IIndoors at an altitude below 1,000m (Do not expose to direct sunlight, or subject to corrosive or flammable gas, oil mist or dust.)

6kg 10kg 17kg 27kg 39kg

※1：Rated capacity: Capacity at an output voltage of 400V※2：Setting frequency range for Sensorless Vector Control: 1Hz to 120Hz※3：Maximum output frequency: Frequency at 5V, 10V, 20mA※4：Acceleration/deceleration time: Time from 0 to the reference acceleration/deceleration frequency.※5：V/f mode: From 0.1 seconds.

※1

※4

※3

※5

※2

Flying start, acceleration/deceleration stall prevention, momentary voltage drop compensation, multiple speed operation, frequency jump, restart after momentary power break, automatic alarm reset, energy-saving operation, pattern operation, PID control operation, torque limiter (only sensorless vector)

0 to 6,500 sec. (independent setting of acceleration/deceleration time possible) Linear or programmable S-curve can be selected.

Frequency command, forward command, reverse command, frequency setting selection, acceleration/deceleration time selection, free-run stop/alarm reset, emergency stop, multiple speed, jogging selection, step frequency selection, operation signal holding, torque limiter (only sensorless vector)

Any base frequency setting between 30Hz and 400Hz can be set. (Constant torque and reduced torque pattern can be selected.)

Current limit, overcurrent shutdown, motor overload, external thermal protection, undervoltage, momentary power break, overvoltage, cooling fin overheat, output open-phase

※3

S P E C I F I C A T I O N S

6

Standard Specifications

Sanken General Purpose Inverter

Model

Applicable motor capacity

Digital

Analog

Digital

Analog

Rated capacity

Rated current

Rated overload current capacity

Rated voltage/frequency

Power supply

Allowable fluctuation

Allowable momentary voltage drop

　

Control method

Modulation method

Setting frequency range

Frequency

setting resolution

Frequency accuracy

Voltage/frequency (V/f)

Torque boost

Acceleration/deceleration time

DC braking

Additional functions

Frequency

setting

Input signals

Output

signals

　�

　　　　　LED display

Protective functions

Ambient temperature

Ambient humidity

Operating environment

IPF-75K

75kW

102kVA

147A

IPF-90K

90kW

120kVA

173A

IPF-110K

110kW

146kVA

211A

IPF-132K

132kW

175kVA

253A

IPF-160K

160kW

211kVA

304A

IPF-280K

280kW

374kVA

540A

IPF-220K

220kW

295kVA

426A

IPF-315K

315kW

409VA

590A

Output

InputC

ontrol functionsO

perational functionsEnvironm

ental

　conditions

Protective structure

Cooling method

Mass (Approx.)

Digital

Analog

Contact output

Open collector output

Analog output

150% for 1 minute

3Φ 380V/50Hz, 400V/50Hz, 460V/60Hz

3Φ 380V to 460V

Voltage: -15%, +10% Frequency: ±5%

320V and above: Continuous operation (short-time rating) Below 320V: 15msec operation

Totally enclosed type (IP20)

Forced air cooling

V/f control or Sensorless Vector Control

Sinusoidal PWM

0.05Hz to 400Hz (starting frequency of 0.05Hz to 20Hz possible)

0.01Hz(0.05Hz to 120Hz)

0.1% (10-bit 0 to 10V, 4 to 20mA), 0.2% (9-bit 0 to 5V) at maximum output frequency

±0.01% of output frequency (at -10℃ to +50℃)

±0.2% of maximum output frequency (at 25 ± 10℃)

0 to 10%

Starting frequency (0.5Hz to 20Hz), braking time (0.1sec to 10 sec), braking force (1 to 10 steps)

Operation panel

0 to 5V, 0 to 10V, 4 to 20mA or variable resistor (5kΩ)

Alarm batch (1C contact 250VAC, 0.3A)

Operation, frequency coincidence, overload warning, undervoltage, frequency reach

Select from setting frequency, output frequency, output current, DC current, heater temperature, load rate, analog input (VRF, IRF)

Frequency, output current, synchronous rotation, line speed (free unit), alarms, charging indicator for capacitor

-10℃ to +50℃�

Below 90% (no condensation allowed)

IIndoors at an altitude below 1,000m (Do not expose to direct sunlight, or subject to corrosive or flammable gas, oil mist or dust.)

70kg65kg 110kg 110kg 1154kg 280kg 280kg160kg

※1：Rated capacity: Capacity at an output voltage of 400V※2：Setting frequency range for Sensorless Vector Control: 5Hz to 120Hz for rated frequency 1, 1Hz to 120Hz for rated frequency 2※3：Maximum output frequency: Frequency at 5V, 10V, 20mA※4：Acceleration/deceleration time: Time from 0 to the reference acceleration/deceleration frequency.※5：V/f mode: From 0.1 seconds.

※1

※4

※5

※5

※2

Flying start, acceleration/deceleration stall prevention, momentary voltage drop compensation, multiple speed operation, frequency jump, restart after momentary power break, automatic alarm reset, energy-saving operation, pattern operation, PID control operation, torque limiter (only sensorless vector)

0 to 6,500 sec. (independent setting of acceleration/deceleration time possible) Linear or programmable S-curve can be selected.

Frequency command, forward command, reverse command, frequency setting selection, acceleration/deceleration time selection, free-run stop/alarm reset, emergency stop, multiple speed, jogging selection, step frequency selection, operation signal holding, torque limiter (only sensorless vector)

Any base frequency setting between 30Hz and 400Hz can be set. (Constant torque and reduced torque pattern can be selected.)

Current limit, overcurrent shutdown, motor overload, external thermal protection, undervoltage, momentary power break, overvoltage, cooling fin overheat, output open-phase

※3

SAMCO-ipF (75kW~315kW)

S P E C I F I C A T I O N S

7

Standard Specifications

Sanken General Purpose Inverter

SAMCO-ihF (1.5kW~15kW)-ipF (7.5kW~18.5kW)

D

B A

C

4－φF

警告�■��■�

xxxxxxxxxxxxxxx�xxxx�xxxxxxxxxxxxxxx�xxxxxxxxxxxxxxx�xxxxxxxx

COIUTUON■��■�

xxxxxxxxxxxxxxx�xxxx�xxxxxxxxxxxxxxx�xxxxxxxxxxxxxxx�xxxxxxxx

FWD REV STOP

DISP�CLEAR

ENTER

PROG

REDY r/min A Hz

E

INVERTER

OUTPUT�

MONITOR�

LOT NO. Mas.

SAMCO-GG-Co. LTD

TYPE

50Hz/60Hz�

o o A�

o o o KW

•Front view •Side view

ModelA B C D E F

ihF Series ipF Series

IHF-1.5K

IHF-2.2K

IHF-4.0K

IHF-5.5K

IHF-7.5K

IHF-11K

IHF-15K

IPF-7.5K

IPF-11K

IPF-15K

IPF-18.5K

250

300

360

238

280

340

140

200

240

128

180

220

155

190

200

5

7

7

(Unit: mm)

S I Z E

8

External Dimensions

Sanken General Purpose Inverter

SAMCO-ihF (18.5kW~55kW)-ipF (22kW~55kW)

D

B A

C

G

2－φF

FWD REV STOP

DISP�CLEAR

ENTER

PROG

REDY r/min A Hz

警告�■��■�

xxxxxxxxxxxxxxx�xxxx�xxxxxxxxxxxxxxx�xxxxxxxxxxxxxxx�xxxxxxxx

COIUTUON■��■�

xxxxxxxxxxxxxxx�xxxx�xxxxxxxxxxxxxxx�xxxxxxxxxxxxxxx�xxxxxxxx

INVERTER

SOUCE　　　　JPN 586V-598V

OUTPUT�MONITOR�LOT NO. Mas.SAMCO-GG-Co. LTD

TYPE

50Hz/60Hz�o o A�

o o o KW

E

•Front view •Side view

ModelA B C D E F G

ihF Series ipF Series

IHF-18.5K

IHF-22K

IHF-30K

IHF-37K

IHF-45K

IHF-55K

IPF-37K

IPF-45K

IPF-22K

IPF-30K

IPF-55K

380

440

580

355

410

550

270

360

360

240

325

325

220

260

270

7

7

9

7

7

9

(Unit: mm)

S I Z E

9

External Dimensions

Sanken General Purpose Inverter

SAMCO-ihF (75kW~250kW)-ipF (75kW~315kW)

D

HB A

C

G

2－φF

FWD REV STOP

DISP�CLEAR

ENTER

PROG

REDY r/min A Hz

INVERTER

SOUCE　　　　JPN 586V-598V

OUTPUT�MONITOR�LOT NO. Mas.SAMCO-GG-Co. LTD

TYPE

50Hz/60Hz�o o A�

o o o KW

�E

2－φ20�（wall-mounting hole）�

•Front view •Side view

ModelA B C D E F G H

ihF Series ipF Series

IHF-110K

IHF-132K

IHF-160K

IHF-250K

IPF-75K

IPF-132K

IPF-160K

IHF-90K IPF-110K

IHF-75K IPF-90K

IPF-220K

IPF-315K

690

690

850

990

1150

655

655

810

950

1100

385

460

530

700

800

300

375

400

600

600

295

295

370

380

465

12

12

12

15

18

12

12

12

15

18

15

15

15

17.5

25

(Unit: mm)

S I Z E

10

External Dimensions

・New publication,effective feb.1999

・Specifications are subject to change without notice.

・For typographical reasons,the color tones of the products featured in this brochure may vary from those of the actual products.

SANKEN ELECTRIC CO., LTD.1-11-1 NISHI-IKEBUKURO, TOSHIMA-KU, TOKYO, JAPANTEL: 03-3986-8061 FAX: 03-3986-6240

SANKEN POWER SYSTEMS (UK) LTD.ABERCYON, MOUNTAIN ASH, MID GLAM., CF45 4XA,SOUTH WALES U.K.TEL: 01443-742333 FAX: 01443-742100

KOREA SANKEN CO.,LTD.BG-1 FREE ZONE EXPORT MASAN 974-17 YANG DUK-DONG,HEOIWON-GU,MASAN KOREATEL:0551-92-5961～6 FAX:0551-96-8938,92-5960

SANKEN L.D.CO.LIMITEDRM.703-704 CONCORDIA PLAZA,1 SCIENCE MUSEUM RD.,T.S.T.EAST,KLN.H.K.TEL:2721-3611,3211-6003 TELEX:48606 LDETC HXFAX:2721-6405 CABLE:1029

SeriesCapacity (kW) SAMCO-ihF

0.4

0.75

1.5

2.2

4.0

5.5

7.5

11

15

18.5

22

30

37

45

55

75

90

110

132

160

220

250

280

315

SAMCO-ipF SAMCO-QS SAMCO-QT SAMCO-iT SAMCO-iF(CE mark)

●：Available now、○Available soon

L I N E - U PSAMCO Series Lineup

Safety PrecautionsBe sure to adhere to the following precautions when using your SAMCO-ihF,ipF Series product.

Be sure to carefully read "Instruction Manual"which is attached with product,before using the unit,then use it correctly.And also,be sure to clearly

follow the operating conditions and environmental conditions listed in this catalog.

The SAMCO-ihF,ipF units are designed for variable speed control of a general,industrial purpose 3-phase AC induction motor.

Note:Contact a customer service representative if any load other than a 3-phase AC induction motor is used.

The SAMCO-ihF,ipF untis shall not be used for the following systems where damage or malfunction could result in injury or loss of life.

a.Passenger transit systems b.Medical facilities c.Nuclear/Electric power control systems d.Aviation/Aerospace systems

e.Traffic/Transportation systems f.Safety systems g.Special purpose systems

Note:Contact a customer service representative before using the unit with these systems.

The SAMCO-ihF,ipF products require certain electrical wiring and should be installed by a qualified electrical technician.

K1-V07EA1-9902005ND