3rd inspection interval inservice inspection program ... · 8. b9.11, zone 21 - changed 2nd period...

212
3 rd Inspection Interval Inservice Inspection Program Summary Manual PVNGS Unit 3 Arizona Public Service Company PVNGS PO Box 52034 5801 S. Wintersburg Road Phoenix, AZ 85072-2034 Tonopah, AZ 85354 Preparer: ____________________________ ___ Reviewer: __________________________________ ANII: __________________________________ Section Leader: ______________________________ Department Leader: __________________________________ Commercial Service Date: 01-08-1988 Program No: 3INT-ISI-3 Rev. 3 1 of 212 3INT-ISI-3, Rev. 3 Cox, Jennifer Y(Z06399) Digitally signed by Cox, Jennifer Y(Z06399) DN: cn=Cox, Jennifer Y(Z06399) Reason: I prepared this document. Date: 2013.08.29 12:02:44 -07'00' Cox, Jennifer Y(Z06399) Digitally signed by Cox, Jennifer Y(Z06399) DN: cn=Cox, Jennifer Y(Z06399) Reason: Signed for Doug Hansen per Telecon Date: 2013.08.29 12:03:22 -07'00' Hogstrom, Robert (YH2450) Digitally signed by Hogstrom, Robert (YH2450) DN: cn=Hogstrom, Robert (YH2450) Date: 2013.08.29 12:18:50 -07'00' Schrecker, Kenneth D(Z99981) Digitally signed by Schrecker, Kenneth D(Z99981) DN: cn=Schrecker, Kenneth D(Z99981) Reason: I am approving this document Date: 2013.08.29 12:38:05 -07'00' Dilorenzo, Michael D(Z99838) Digitally signed by Dilorenzo, Michael D(Z99838) DN: cn=Dilorenzo, Michael D(Z99838) Reason: Program Engineering Department Leader Date: 2013.08.29 12:46:32 -07'00' Cox, Jennifer Y(Z06399) Digitally signed by Cox, Jennifer Y(Z06399) DN: cn=Cox, Jennifer Y(Z06399) Reason: I transmitted this document. Date: 2013.08.29 13:15:18 -07'00'

Upload: others

Post on 20-Jul-2020

5 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

3rd Inspection Interval

Inservice Inspection Program Summary Manual

PVNGS Unit 3

Arizona Public Service Company PVNGS PO Box 52034 5801 S. Wintersburg Road Phoenix, AZ 85072-2034 Tonopah, AZ 85354

Preparer: ____________________________ ___ Reviewer: __________________________________ ANII: __________________________________ Section Leader: ______________________________

Department Leader: __________________________________

Commercial Service Date: 01-08-1988

Program No: 3INT-ISI-3 Rev. 3

1 of 212 3INT-ISI-3, Rev. 3

Cox, Jennifer Y(Z06399)

Digitally signed by Cox, Jennifer Y(Z06399) DN: cn=Cox, Jennifer Y(Z06399) Reason: I prepared this document. Date: 2013.08.29 12:02:44 -07'00'

Cox, Jennifer Y(Z06399)

Digitally signed by Cox, Jennifer Y(Z06399) DN: cn=Cox, Jennifer Y(Z06399) Reason: Signed for Doug Hansen per Telecon Date: 2013.08.29 12:03:22 -07'00'

Hogstrom, Robert (YH2450)

Digitally signed by Hogstrom, Robert (YH2450) DN: cn=Hogstrom, Robert (YH2450) Date: 2013.08.29 12:18:50 -07'00'

Schrecker, Kenneth D(Z99981)

Digitally signed by Schrecker, Kenneth D(Z99981) DN: cn=Schrecker, Kenneth D(Z99981) Reason: I am approving this document Date: 2013.08.29 12:38:05 -07'00'

Dilorenzo, Michael D(Z99838)

Digitally signed by Dilorenzo, Michael D(Z99838) DN: cn=Dilorenzo, Michael D(Z99838) Reason: Program Engineering Department Leader Date: 2013.08.29 12:46:32 -07'00'

Cox, Jennifer Y(Z06399)

Digitally signed by Cox, Jennifer Y(Z06399) DN: cn=Cox, Jennifer Y(Z06399) Reason: I transmitted this document. Date: 2013.08.29 13:15:18 -07'00'

Page 2: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

TABLE OF CONTENTS

Summary of Changes………………………………………………………………. 3

1.0 Summary ......................................................................................................... 5

2.0 Code Applicability .......................................................................................... 5

3.0 Description ...................................................................................................... 6 3.1 Scope ............................................................................................................ 6 3.2 System Boundaries ....................................................................................... 7 3.3 Accessibility ................................................................................................. 7 3.4 Examination Techniques .............................................................................. 8 3.5 Inspection Intervals ....................................................................................... 8 3.6 Examination Categories ................................................................................ 9 3.7 Evaluation and Repair ................................................................................... 9 3.8 System Pressure Tests................................................................................... 9 3.9 Exemptions ................................................................................................... 9 3.10 Code Cases ................................................................................................. 10 3.11 Outage Plan Table....................................................................................... 10 3.12 References .................................................................................................. 11

4.0 ASME Class 1 Summary ............................................................................... 12

5.0 ASME Class 2 Summary ............................................................................... 38

6.0 ASME Class 3 Summary ............................................................................... 71

7.0 Augmented Summary .................................................................................... 78

8.0 Requests for Relief ........................................................................................ 91

9.0 Boundary Drawing Listing ............................................................................ 93

10.0 Zone Drawings .............................................................................................. 95

11.0 Terms and Definitions ................................................................................. 210

2 of 212 3INT-ISI-3, Rev. 3

Page 3: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SUMMARY OF CHANGES

Revision 3

1. Section 3.1.1 – Added reference to TRM 5.0.500.8. Added refererence to program exceptions in Section 3.1.3

2. Section 3.1.3 – Added more detail about Programs that cover parts of Section XI.

3. B6.180 – Deleted reference to Aug_B6.180 since that section was removed during the last revision.

4. B7.20 – Deleted reference to Aug_B7.20 since that section was removed during the last revision. Updated counts to reflect number of entries in Iddeal.

5. B7.30 – Deleted reference to Aug_B7.30 since that section was removed during the last revision. Updated counts to reflect number of entries in Iddeal.

6. B7.50 – Added note to see also Aug_B15.10.

7. B7.70 – Updated counts to reflect number of entries in Iddeal. Put zone numbers in order. (ACT 4424891)

8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done to accommodate for train outages. (ACT 4424891)

9. B9.11, Zone 22 - Changed 2nd period requirements from 3 to 7. Deleted 3rd period requirements. This is to accommodate for train outages. (ACT 4424891)

10. B9.22, Zone 39 - Deleted 2nd period requirements. This is to accommodate for train outages. Updated percentages accordingly. (ACT 4424891)

11. B9.22, Zone 40 - Changed 2nd period requirements from 4 to 10. This is to accommodate for train outages. Updated percentages accordingly. (ACT 4424891)

12. B9.40 – Changed first period requirements from 1 to 2 in order to credit inspections already completed. (ACT 4424891)

13. B16.20 – Corrected ASME Category.

14. C5.81 - Adjusted required exam amounts to 1 weld per zone to match 7.5% requirements of C-F-2. (ACT 4424891)

15. F1.20C - Update counts based on document review. (ACT 4424891)

16. F1.20C, Zone 52 - Add one 2nd period inspection since counts in Zone 96 declined. (ACT 4424891)

17. F1.20C, Zone 96 - Update total items from 8 to one. Change inspection amount from 2 to 1. (ACT 4424891)

18. F1.20C, Zone 99 - Update inspection amount from 2 to 1. One exam during 2nd period is a successive

exam and will not count for credit. (ACT 4424891)

19. F1.20C, Zone 102 – Updated counts. Delete reference to SI-008. (ACT 4424891)

20. D1.20 – Added 4 DG components and adjusted exam amounts per CRAI 4420282. (CRAI 4420812) Reduced exam amount required to better align program with code requirements.

21. F1.30B, DG – Added 22 components and adjusted exam amounts per CRAI 4420282. (CRAI 4420812) Reduced exam amount to better align program with code requirements.

3 of 212 3INT-ISI-3, Rev. 3

Page 4: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

22. N-770-1, Item F - Note about 3 year Design Calc Exam cut off in previous revision. Updated to "Required R17, R19, and R21." (ACT 4424891) Deleted note about “*CIRCUMFERENTIAL WELDS” since note was left over from a previous component classification.

23. Aug_B15.10, Closure head nuts - Note cut off in previous revision. Updated to say "Deleted from program per ACT 4162637." (ACT 4424891)

24. Aug_B15.10, Closure Head Studs – Added note to see also B6.20.

25. Aug_B15.10, Zone 5 – Added note to see also B7.20.

26. AUG_B15.10, Zones 3 & 4 – Added note to see also B7.30.

27. AUG_B15.10, Zone 31 – Added note to see also B7.50.

28. AUG_C5.11 & AUG_C5.51 – Reversed order of item numbers to put them in numeric order.

29. AHE5.51 - Moved remaining exams to Period 3. (ACT 4424891)

30. AHE5.61 - Move remaining exams to Period 3. (ACT 4424891)

4 of 212 3INT-ISI-3, Rev. 3

Page 5: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

PALO VERDE NUCLEAR GENERATING STATION

UNIT 3 INSERVICE INSPECTION - PROGRAM SUMMARY

1.0 SUMMARY

1.1 This document contains a detailed description of the 3rd 10 Year Interval Inservice Inspection (ISI) Program for Palo Verde Nuclear Generating Station Unit 3. This program conforms to the requirements of 10 CFR 50.55a (g), PVNGS Technical Specifications, and the PVNGS UFSAR. Exceptions that are known as of this document preparation date are included in the Requests for Relief Section 8.0.

1.2 The revision is being prepared to update the ISI Program for the 3rd 10 Year Interval. This includes the utilization of the 2001 Edition including the 2003 Addenda of ASME Section XI with the exceptions noted below:

1.2.1 Requests for relief from ASME Section XI requirements are included in Section 8.0. These Relief Requests are prepared in a format similar to that documented in the NEI White Paper Revision 1 dated June 2004, entitled: “Standard Format for Requests from Commercial Reactor Licensees Pursuant to 10 CFR 50.55a”.

1.2.2 The 2007 Edition thru the 2008 Addenda was utilized for Categories B-L-1, B-M-1, and C-G for pump and body weld requirements. (Ref. Letter 102-06454 and SER dated 09-18-2012.) (ACT 4343138)

1.2.3 For clarification, this Interval 3 program was prepared, as was Interval 1 and 2 programs, utilizing 40 month periods.

1.2.4 To support future ISI Programs, reference to the Reactor Vessel Internals Aging Management Plan was added (Reference 3.12.3). (CRAI 4353644)

1.2.5 This program was updated to include MRP-192 examinations of mixing tee locations (Reference 3.12.4). (CRAI 4312834)

1.3 This revision does not utilize risk informed inservice inspection methodology at this time.

1.4 The information presented is in a form consistent with the 1st and 2nd 10 Year Interval ISI Program, the applicable requirements of Standard Review Plan manual and procedures and the recommendations contained in NRC letter dated July 17, 1981, from Mr. R.L. Tedesco, NRC, to E. E. Van Brunt, Jr., APS, “Guidance for Preparing Preservice and Inservice Inspection Programs and Relief Requests - Palo Verde Nuclear Generating Station Units 1, 2 and 3.”

2.0 CODE APPLICABLILITY

2.1 Based on paragraph 10 CFR 50.55a(b) (2) that was published 12 months prior to the start of the 3rd 10 Year Interval (1-11-08), the 2001 Edition including the 2003 Addenda of ASME Section XI was referenced as the Code to utilize for preparation of this program. Several exceptions to this code are documented in 10 CFR 50.55a; each of these exceptions was utilized during the preparation of this program.

• The exemptions of IWB-1220 for Class 1 piping must utilize the 1989 Edition.

5 of 212 3INT-ISI-3, Rev. 3

Page 6: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

• When qualifying VT-3 personnel per IWA-2317, the proficiency of the training must be demonstrated by initial qualification examination and subsequent examinations on a 3 year interval.

• The 1997 Edition must be used for IWA-2240 alternative examination methods, a combination of methods, or newly developed techniques.

• Items B3.120 and B3.140 (nozzle inner radius examinations) of the 1998 Edition must be utilized. An enhanced visual examination with a resolution sensitivity to detect a 1-mil wire or crack may be performed in place of an ultrasonic examination.

• Must utilize the 1995 Edition for examination Item B7.80 per 50.55a (b)(2)(xxi)(B).

• IWA-2220, Ultrasonic examination methods are prohibited for surface examinations.

• The surface examination requirements for HPSI systems, Items B9.20, B9.21 and B9.22 are not required to be performed.

2.2 If a code required examination was considered to be impractical during the preparation of this document because of plant design, geometry, accessibility or other conditions, a Request for Relief from that requirement was prepared and included in Section 8.0. If a code required examination is identified to be impractical during the course of an inspection and the code required percentages are not met, a request for relief will be prepared and submitted after each inspection period, and the final interval closeout no later than 12 months after expiration of the Interval.

2.3 This ISI Program will implement the ASME Section XI, 2001 Edition, Appendix VIII (Performance Demonstration for Ultrasonic Examination Systems) in accordance with 10 CFR 50.55a. These examinations will be conducted in accordance with the Performance Demonstration Initiative (PDI). The PDI Code Comparison document (Reference 3.12.2) explains the complex relationship of regulatory requirements, ASME requirements, code editions, and the PDI program. (CRAI 4378832)

3.0 DESCRIPTION

3.1 SCOPE

3.1.1 This Inservice Inspection Program Summary includes all applicable nondestructive examinations required by ASME Section XI as identified below:

1. Examination of ASME Class 1, 2, and 3 pressure retaining components and their supports are performed in accordance with TRM 5.0.500.8.

2. Items that may generally be included in an Inservice Inspection Program, but are not included are listed in Section 3.1.3.

3.1.2 This program also includes an augmented section that includes examinations for other items required to be examined as identified below.

1. Examinations of welds in Class 1 components fabricated with Alloy 600/82/182 materials in accordance with 10 CFR 50.55a and Code Case N-722-1.

2. Examination of the Reactor Vessel Closure Head in accordance with 10 CFR 50.55a and Code Case N-729-1.

6 of 212 3INT-ISI-3, Rev. 3

Page 7: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

3. Examination of welds in Class 1 piping and vessel nozzle butt welds fabricated with alloy 82/182 in accordance with 10 CFR 50.55a and Code Case N-770-1.

4. Examination of high energy line piping in accordance with UFSAR 6.6.1. (CRAI 4178277)

5. Examination of the Reactor Coolant Pump Flywheels in accordance with PVNGS Technical Specifications Section ITS 5.5.7.

6. USNRC Circulars, Information Notices, Bulletins, or Orders

7. INPO or other industry operating experiences

8. Combustion Engineering or Westinghouse bulletins or notices

9. Special examinations to satisfy other commitments or concerns that are based on operating experiences, USNRC. These examinations are scheduled throughout this program and reference the applicable notification documents.

3.1.3 Those items that may generally be included in an Inservice Inspection Program, but are not included are identified below:

1. The pressure testing of ASME Class 1, 2, and 3 piping will be performed in accordance with the Pressure Testing Program.

2. The inservice examination of steam generator tubing will be performed in accordance with the PVNGS Technical Specifications Section T5.5.9 under the Steam Generator Degradation Management Program.

3. The inservice testing of snubbers will be performed in accordance with 10 CFR 50.55a under the Snubber Program.

4. The Examination Program for the ASME Subsections IWE and IWL will be performed in accordance with 10 CFR 50.55a and the PVNGS Technical Specifications under the IWE and IWL Programs.

6. Repair and replacements are performed under the Repair and Replacement Program (73DP-9ZZ17)

3.2 SYSTEM BOUNDARIES

3.2.1 A complete set of P&ID drawings indicating the Inservice Inspection boundary are maintained at the PVNGS site. These drawings illustrate the ASME Class 1, 2, and 3 systems; components; and boundaries scheduled for examinations and pressure testing. A referenced listing of these drawings is documented in Section 9.0.

3.2.2 A set of ISI (Zone) Drawings is included in Section 10.0. These drawings are utilized for the planning and scheduling of specific ASME Class 1 and 2 examinations throughout the 10 Year Interval. These also document the location and number of welds, components, and supports. (CRAI 4398777)

3.3 ACCESSIBILITY

3.3.1 The preservice examinations were performed with examination techniques, automated or manual, similar to those planned for use during Inservice Inspections. The examination limitations noted during the preservice examinations were documented in

7 of 212 3INT-ISI-3, Rev. 3

Page 8: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

Requests for Relief submitted with the preservice examination program. There has also been a number of additional code limitations noted during the 1st and 2nd 10 Year Intervals and Request for Relief submitted. If included in the required 3rd Interval examinations they will again be evaluated and relief requested. Note Section 8.0 identifies all the reliefs submitted during the preparation and implementation of the 3rd Interval.

3.3.2 All items that are scheduled for examination will be examined to the extent practical. In addition, any code limitations that are noted during the examinations will be documented. If relief is required from any of these examinations, a Request for Relief will be submitted after the relief is discovered and prior to 12 months after the interval ends.

3.4 EXAMINATION TECHNIQUES

3.4.1 The three types of examinations utilized to perform Inservice Inspections, along with the actual nondestructive examination technique, are identified in the legend below:

VT - Visual

VT - 1 (General Condition) VT - 2 (Leakage) VT - 3 (Mechanical and Structural Condition) VE (Visual Examination)

S - Surface

PT - Liquid Penetrant MT - Magnetic Particle ET - Eddy Current

VOL - Volumetric

UT - Ultrasonic RT - Radiography

3.4.2 All the above nondestructive examination techniques will be performed using specific techniques and procedures that are identified in ASME Section XI, or alternative examinations that are demonstrated to be equivalent or superior to those identified. The provision for substitution of these alternative examination methods, combination of methods, or newly developed techniques will utilize the 1997 Addenda for IWA-2240.

3.5 INSPECTION INTERVALS

3.5.1 The Inservice Inspection Program was prepared in accordance with Program B of ASME Section XI. The 1st, 2nd, and 3rd 10 Year Intervals and corresponding inspection periods are defined below:

First Inspection Interval: 01-08-88 to 01-10-98

Second Inspection Interval: 01-11-98 to 01-10-08

Third Inspection Interval: 01-11-08 to 01-10-18 Period One: 01-11-08 to 05-10-11 Period Two: 05-11-11 to 09-10-14 Period Three: 09-11-14 to 01-10-18

8 of 212 3INT-ISI-3, Rev. 3

Page 9: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

It should be noted that the intervals/periods may change to allow for extended outage durations per IWA-2400 of ASME Section XI.

3.6 EXAMINATION CATEGORIES

3.6.1 The examination categories of ASME Section XI were utilized to develop this program for all systems, components, and supports. The Subprogram summary tables contained in Sections 4.0 and 5.0 are organized by examination category for ASME Class 1 and 2 systems, respectively. For each examination category, these tables identify the system or identification, nondestructive examination method, total number of items, required examination amount for each inspection period, and running percentage. For ASME Class 3 systems, the examinations categories are identified in Section 6.0.

3.7 EVALUATION AND REPAIR

3.7.1 The evaluation of all examination results will be performed in accordance with ASME Section XI Articles IWx-3000. In addition, all applicable repairs and replacements will be performed in accordance with ASME Section XI Articles IWX-4000 and 7000. Pressure tests will be performed on welded and mechanical joint repairs or replacements, in accordance with IWx-4000 and 5000 and 10 CFR 50. Both the evaluations and repair or replacement will be performed in accordance with the 2001 Edition including the 2003 Addenda of ASME Section XI, or later editions and addenda of ASME Section XI referenced in 10 CFR 50. Later editions and addenda will be documented with the NRC.

3.7.2 It should be noted that a relief was requested (Relief Request 36) to perform repair and replacement of all three PVNGS units to the 2001 Edition including the 2003 Addenda. This request was documented in conjunction with the relief to perform full structural weld metal overlays. (APS letter to the USNRC 102-05641 dated 2-8-2007).

3.7.3 All repairs and replacements will be documented in accordance with the Work Control program, and are maintained at Palo Verde for review.

3.8 SYSTEM PRESSURE TESTS

3.8.1 ASME Class 1, 2, and 3 components will be pressure tested per the requirements of IWB-5000, IWC-5000 and IWD-5000, except where relief has been requested.

3.8.2 Pressure tests will also be performed on repairs and replacements per ASME Section XI, 10 CFR 50.55a, and the PVNGS Repair and Replacement program.

3.9 EXEMPTIONS

3.9.1 The exemption criteria identified in the 2001 Edition including the 2003 Addenda of ASME Section XI was utilized for all ASME Class 1, 2, and 3 components and systems. The only exception is that required by 10 CFR 50.55a for the ASME Class 1 piping exemptions. These are in accordance with the 1989 Edition of ASME XI.

3.9.2 A thorough review of all the systems and components was performed in accordance with the above exemptions and a complete set of color coded Inservice Inspection Exemption drawings was prepared. These drawings are maintained at the PVNGS site for review.

9 of 212 3INT-ISI-3, Rev. 3

Page 10: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

3.10 CODE CASES

3.10.1 The following Code Cases are accepted for use in Regulatory Guide 1.147 and may be utilized during Interval 3 where applicable (CRAIs 4404322, 4338597, and 4308456):

1. N-460 Alternative examination coverage for Class 1 and 2 welds 2. N-526 Alternative requirements for successive inspections of Class 1 and 2 vessels 3. N-532-4 Alternative requirements to repair and replacement documentation 4. N-534 Alternative Requirements for Pneumatic Pressure Testing. 5. N-537 Location of Ultrasonic Depth-Sizing Flaws 6. N-566-2 Corrective Action for Leakage Identified at Bolted Connections 7. N-613-1 Ultrasonic examination of full penetration nozzles in vessels 8. N-624 Successive inspections 9. N-652-1 Alternative requirements to categories B-G-1, B-G-2, and C-D bolting 10. N-663 Alternative Requirements for Classes 1 and 2 Surface Examinations 11. N-666 Weld Overlay of Class 1, 2, and 3 Socket Welded Connections 12. N-685 Lighting Requirements for Surface Examinations 13. N-695 Alternative for Qualification Requirements for Dissimilar Metal Piping Welds,

Appendix VIII Supplement 10 14. N-700 Alternative Rules for Selection of Class 1, 2, and 3 Vessel Welded Attachments for Examination 15. N-705 Evaluation Criteria for Temporary Acceptance of Degradation in Moderate Energy Class 2 or 3 Vessels and Tanks, Section XI, Division 1

3.10.2 The following Code Cases are conditionally accepted for use in Regulatory Guide 1.147 may be utilized with the specified conditions during Interval 3 where applicable:

1. N-513-3 Evaluation Criteria for Temporary Acceptance of Flaws in Moderate Energy Class 2 or 3 Piping

RG 1.147 documents acceptance condition is that the repair or replacement activity temporarily deferred under the provisions of this Code Case shall be performed during the next scheduled outage.

2. N-648-1 Alternative requirements for inner radius examinations of reactor vessel nozzles

RG 1.147 documents acceptance condition is that in place of a UT examination, licensees may perform a visual examination with enhanced magnification that has a resolution sensitivity to detect a 1-mil width wire or crack, utilizing the allowable flaw length criteria of Table IWB-3512-1 with limiting assumptions on the flaw aspect ratio. The provisions of Table IWB-2500-1, Examination Category B-D, continue to apply except that, in place of examination volumes, the surfaces to be examined are the external surfaces shown in the figures applicable to this table (the external surface is from point M to point N in the figure).

3.10.3 The following Code Cases are required to be utilized by 10 CFR 50.55a with

additional specified conditions. These are planned to be utilized with the specified conditions during Interval 3:

1. N-722-1 Additional Examinations for PWR Pressure Retaining Welds in Class 1 Components Fabricated With Alloy 600/82/182 Materials 2. N-729-1 Alternative Examination Requirements for PWR Reactor Vessel Upper Heads With Nozzles Having Pressure-Retaining Partial-Penetration Welds 3. N-770-1 Alternative Examination Requirements and Acceptance Standards for Class 1 PWR Piping and Vessel Nozzle Butt Welds Fabricated With UNS N06082 or UNS W86182 Weld filler Material With or Without Application of Listed Mitigation Activities (See Reference 3.12.1, CRAI 4348781)

3.11 OUTAGE PLAN TABLE

The outage plan table, controlled by procedure 73DP-9XI03 and 73DP-9EE02, identifies the components scheduled for examination including successive examinations from prior periods. The examination procedures and a listing of calibration blocks are also identified.

10 of 212 3INT-ISI-3, Rev. 3

Page 11: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

3.12 REFERENCES

3.12.1 SDOC N001-0604-00903 (Supplier Dwg No. PV23Q405), “DESIGN REPORT FOR PREEMPTIVE WELD OVERLAY REPAIRS PRESSURIZER AND HOT LEG DISSIMILAR METAL WELDS PALO VERDE NUCLEAR GENERATING STATION UNITS 1, 2, AND 3 FOR ARIZONA PUBLIC SERVICE, Rev. 1, dated 05/25/2011. (CRAI 4348781)

3.12.2 EPRI 2012 Technical Report 1026510, “Nondestructive Evaluation: Performance Demonstration Initiative (PDI) Comparisons to ASME Section XI, Appendix VIII 2007 Edition with 2008 Addendum, and 10 CFR 50.55a, Year 2011,” dated November 2012. (CRAI 4378832)

3.12.3 SDOC MN755-A00003, “PWR INTERNALS AMP FOR PALO VERDE,” Rev. 0, dated 09/07/2012. (CRAI 4353644)

3.12.4 EPRI 2012 Technical Report 1024994, “Materials Reliability Program: Assessment of Residual Heat Removal Mixing Tee Thermal Fatigue in PWR Plants,” dated August 2012. (CRAI 4312834)

11 of 212 3INT-ISI-3, Rev. 3

Page 12: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 4.0 ASME CLASS 1

EXAMINATION SUMMARY

12 of 212 3INT-ISI-3, Rev. 3

Page 13: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

INDEX

EXAM CATEGORIES

B-A Pressure Retaining Welds in Reactor Vessel

B-B Pressure Retaining Welds in Vessels Other Than Reactor Vessels

B-D Full Penetration Welded Nozzles in Vessels

B-F Pressure Retaining Dissimilar Metal Welds in Vessel Nozzles

B-G-1 Pressure Retaining Bolting, Greater Than 2 Inches in Diameter

B-G-2 Pressure Retaining Bolting, 2 Inches and Less in Diameter

B-J Pressure Retaining Welds in Piping

B-K Welded Attachments for Vessels, Piping, Pumps and Valves

B-L-2 & B-M-2 Pump Casings and Valve Bodies

B-N-1 Interior of Reactor Vessel

B-N-2 Welded Core Support Structures and Interior Attachments to Reactor Vessels

B-N-3 Removable Core Support Structures

B-O Pressure Retaining Welds in Control Rod Housings

B-P All Pressure Retaining Components

B-Q Steam Generator Tubing

F-A Class 1 Supports

13 of 212 3INT-ISI-3, Rev. 3

Page 14: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-A

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN R

EAC

TOR

VES

SEL

*Aut

o ex

am w

ith c

ore

barr

el re

mov

ed

B1.

10S

HE

LL W

ELD

SB

1.11

CIR

CU

MFE

RE

NTI

AL

1-R

eact

or V

esse

lw

elds

6517

3V

ol3

01

0

02

0**

0*3

0**

Rel

ief R

eque

st 4

0E

xam

ine

in 2

028

B1.

12LO

NG

ITU

DIN

AL

1-R

eact

or V

esse

lw

elds

6517

3V

ol9

01

00

20

**0*

30

B1.

20H

EA

D W

ELD

SB

1.21

CIR

CU

MFE

RE

NTI

AL

B1.

22M

ER

IDIO

NA

L1-

Rea

ctor

Ves

sel B

otto

m H

ead

wel

d65

173

Vol

10

10

02

0**

0*3

0

2-C

losu

re H

ead

wel

dN

0506

5-C

HA

-03

Vol

00

10

No

long

er a

pplie

s;0

20

RV

H R

epla

ced

R15

03

0

B1.

30S

HE

LL-T

O-F

LAN

GE

WE

LD1-

Rea

ctor

Ves

sel

wel

d65

173

Vol

10

10

02

0**

0*3

0

B1.

40H

EA

D-T

O-F

LAN

GE

WE

LD2-

Clo

sure

Hea

dw

eld

N05

065-

CH

A-0

3S

& V

ol0

01

0N

o lo

nger

app

lies;

02

0R

VH

Rep

lace

d R

150

30

14 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 15: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-B

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

VESS

ELS

OTH

ER T

HA

N

REA

CTO

R V

ESSE

LS

*cat

egor

y ru

nnin

g pe

rcen

t-

--

-3

133

22

554

310

0P

RE

SS

UR

IZE

RB

2.10

SH

ELL

-TO

-HE

AD

WE

LDS

B2.

11C

IRC

UM

FER

EN

TIA

L

5-

Pre

ssur

izer

wel

d65

373

Vol

21

11

3B

2.12

LON

GIT

UD

INA

L **

5-

Pre

ssur

izer

wel

d65

373

Vol

42

1**

1' o

f eac

h2

3in

ters

ectin

g ci

rcex

am a

rea

STE

AM

GE

NE

RA

TOR

S *

**B

2.30

HE

AD

WE

LDS

B2.

31C

IRC

UM

FER

EN

TIA

L**

* M

ultip

le V

esse

ls3-

S

team

Gen

erat

or 1

wel

d24

2V

ol1

12

4-

Ste

am G

ener

ator

2w

eld

243

Vol

1

B2.

40TU

BE

SH

EE

T TO

HE

AD

3-

Ste

am G

ener

ator

1w

eld

242

Vol

21

24-

S

team

Gen

erat

or 2

wel

d24

3V

ol2

13

15 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 16: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-D

; FU

LL P

ENET

RA

TIO

N

WEL

DED

NO

ZZLE

S IN

VES

SELS

-IN

SPEC

TIO

N P

RO

GR

AM

BR

EA

CTO

R V

ES

SE

L B

3.90

NO

ZZLE

-TO

-VE

SS

EL

WE

LDS

1-

Rea

ctor

Ves

sel

Out

lets

- 2

6517

3V

ol6

0*3

0 *

Rel

ief R

eque

st 4

0 In

lets

- 4

Exa

min

e in

202

8

B3.

100

NO

ZZLE

INS

IDE

RA

DIU

S S

EC

TIO

N

1-

Rea

ctor

Ves

sel

Out

lets

- 2

6517

3V

ol6

0*3

0 *

Rel

ief R

eque

st 4

0In

lets

- 4

Exa

min

e in

202

8

PR

ES

SU

RIZ

ER

B3.

110

NO

ZZLE

-TO

-VE

SS

EL

WE

LDS

5-

Pre

ssur

ize r

Sur

ge -

165

373

Vol

62

133

Spr

ay -

12

267

Saf

etie

s - 4

23

100

B3.

120

NO

ZZLE

INS

IDE

RA

DIU

S S

EC

TIO

N**

**U

se 1

998

ed. p

er50

.55a

(b)(

2)(x

xi)(

A).

5-

Pre

ssur

izer

Sur

ge -

165

373

Vol

62

133

Spr

ay -

12

267

Saf

etie

s - 4

23

100

16 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 17: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

STE

AM

GE

NE

RA

TOR

S

B3.

130

NO

ZZLE

-TO

-VE

SS

EL

WE

LDS

B3.

140

NO

ZZLE

INS

IDE

RA

DIU

S S

EC

TIO

N**

*B3.

130

& B

3.14

0 ru

nnin

g pe

rcen

t-

--

-4

133

42

674

310

0

B3.

130

3-

Ste

am G

ener

ator

1In

let -

124

2V

ol3

11

Out

let -

22

2

4-

Ste

am G

ener

ator

2In

let -

124

3V

ol3

11

Out

let -

22

3

B3.

140

NO

ZZLE

INS

IDE

RA

DIU

S S

EC

TIO

N**

**U

se 1

998

ed. p

er50

.55a

(b)(

2)(x

xi)(

A).

3-

Ste

am G

ener

ator

1In

let -

124

2V

ol3

11

Out

let -

22

2

4-

Ste

am G

ener

ator

2In

let -

124

3V

ol3

11

Out

let -

22

3

17 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 18: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-F

; PR

ESSU

RE

RET

AIN

ING

DIS

SIM

ILA

R M

ETA

L W

ELD

S IN

VE

SSEL

NO

ZZLE

S

PR

ES

SU

RIZ

ER

B5.

40

NO

MIN

AL

PIP

E S

IZE

> 4

INC

H

NO

ZZLE

TO

SA

FEE

ND

BU

TT

WE

LDS

20-

Sur

gebu

tt w

elds

RC

-028

-12”

S &

Vol

6*

*33

*Miti

gate

d w

ith F

SW

O29

- S

pray

butt

wel

dsR

C-0

18-4

”S

& V

ol*

*66

Mov

ed to

Aug

men

ted

31-

Saf

etie

s (4

)bu

tt w

elds

RC

-001

-6”

S &

Vol

**

100

Tabl

esR

C-0

03-6

”S

& V

olR

C-0

05-6

”S

& V

olR

C-0

07-6

”S

& V

ol

EXA

M C

ATE

GO

RY

B-G

-1; P

RES

SUR

E R

ETA

ININ

G B

OLT

ING

GR

EATE

R T

HA

N 2

IN.

IN D

IAM

ETER

RE

AC

TOR

VE

SS

EL

B6.

10C

LOS

UR

E H

EA

D N

UTS

2-

Clo

sure

Hea

dnu

ts7.

237”

x 7

.91"

VT-

154

181

33

02

66

363

100

B

6.20

CLO

SU

RE

STU

DS

2-

Clo

sure

Hea

dst

uds

7.38

0” x

76.

37"

Vol

5418

133

See

als

o A

UG

_B15

.10.

182

6618

310

0

B6.

40TH

RE

AD

S IN

FLA

NG

E

1-

Rea

ctor

Ves

sel

Stu

d H

oles

6517

3V

ol54

01

00

20

543

100

18 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 19: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

B6.

50C

LOS

UR

E W

AS

HE

RS

BU

SH

ING

S

2-

Clo

sure

Hea

dW

ashe

rs7.

50” x

1.2

7”V

T-1

5418

133

02

6636

310

0

PU

MP

SB

6.18

0B

OLT

S A

ND

STU

DS

16-

Rea

ctor

Coo

lant

Pum

p 1A

Flan

ge S

tuds

4.33

” x 3

2.87

”V

ol16

161

100

* M

ultip

le p

umps

17-

Rea

ctor

Coo

lant

Pum

p 1B

Flan

ge S

tuds

4.33

” x 3

2.87

”V

ol16

**

18-

Rea

ctor

Coo

lant

Pum

p 2A

Flan

ge S

tuds

4.33

” x 3

2.87

”V

ol16

**

19-

Rea

ctor

Coo

lant

Pum

p 2B

Flan

ge S

tuds

4.33

” x 3

2.87

”V

ol16

**

B6.

190

FLA

NG

E S

UR

FAC

E W

HE

N

CO

NN

EC

TIO

N D

ISA

SS

EM

BLE

D

** V

T-1

exam

s on

1

pum

p pe

r int

erva

l (w

ith

B12

.XX

exa

ms)

16-

Rea

ctor

Coo

lant

Pum

p 1A

surfa

ce11

11-1

AV

T-1

1**

****

17-

Rea

ctor

Coo

lant

Pum

p 1B

surfa

ce11

11-1

BV

T-1

1**

****

18-

Rea

ctor

Coo

lant

Pum

p 2A

surfa

ce11

11-2

AV

T-1

1**

****

19-

Rea

ctor

Coo

lant

Pum

p 2B

surfa

ce11

11-2

BV

T-1

1**

****

B6.

200

NU

TS, B

US

HIN

GS

, AN

D W

AS

HE

RS

** V

T-1

exam

s on

1

pum

p pe

r int

erva

l (w

ith

B12

.XX

exa

ms)

16-

Rea

ctor

Coo

lant

Pum

p 1A

nuts

& ri

ng11

11-1

AV

T-1

16**

****

17-

Rea

ctor

Coo

lant

Pum

p 1B

nuts

& ri

ng11

11-1

BV

T-1

16**

****

18-

Rea

ctor

Coo

lant

Pum

p 2A

nuts

& ri

ng11

11-2

AV

T-1

16**

****

19-

Rea

ctor

Coo

lant

Pum

p 2B

nuts

& ri

ng11

11-2

BV

T-1

16**

****

19 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 20: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-G

-2; P

RES

SUR

E R

ETA

ININ

G B

OLT

ING

2 IN

. AN

D L

ESS

IN

DIA

MET

ER

***

VT-

1 ex

ams

requ

ired

each

refu

elin

g w

hen

disa

ssem

bled

PR

ES

SU

RIZ

ER

B7.

20B

OLT

S, S

TUD

S A

ND

NU

TS

See

als

o A

UG

_B15

.10.

5-

Pre

ssur

izer

Man

way

Stu

ds &

Nut

s1.

31” x

14.

5”V

T-1

11

***

***

(20

sets

of b

oltin

g)

STE

AM

GE

NE

RA

TOR

B7.

30B

OLT

S, S

TUD

S A

ND

NU

TS

See

als

o A

UG

_B15

.10.

3-

Ste

am G

ener

ator

1 M

AN

WA

YS

Stu

ds &

Nut

s1.

31” x

14.

5”V

T-1

22

***

***

(20

sets

of h

ot le

g bo

lting

, 20

sets

of

cold

lege

bol

ting)

4-

S

team

Gen

erat

or 2

MA

NW

AY

SS

tuds

& N

uts

1.31

” x 1

4.5”

VT-

12

2**

***

*(2

0 se

ts o

f hot

leg

bolti

ng, 2

0 se

ts o

f co

ld le

ge b

oltin

g)

PIP

ING

****

Whe

n di

sass

embl

ed a

nd

only

onc

e pe

r in

terv

al. O

ne b

olte

d co

nnec

tion

amon

g a

grou

p of

sim

ilar

bolte

d co

nnec

tions

. (A

CT

4162

637)

B7.

50B

OLT

S, S

TUD

S A

ND

NU

TSS

ee a

lso

AU

G_B

15.1

0.31

- P

ress

uriz

er S

afet

ies

Flan

ge B

oltin

gR

C-0

01-6

”V

T-1

88

****

****

Flan

ge B

oltin

gR

C-0

03-6

”V

T-1

88

****

****

Flan

ge B

oltin

gR

C-0

05-6

”V

T-1

88

****

****

20 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 21: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

Flan

ge B

oltin

gR

C-0

07-6

”V

T-1

88

****

****

37-

Cha

rgin

g Li

neFl

ange

V43

5C

H-0

05-2

”V

T-1

88

****

****

21 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 22: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

PU

MP

S

One

bol

ted

conn

ectio

n am

ong

a gr

oup

of s

imila

r bo

lted

conn

ectio

ns.

B7.

60B

OLT

S, S

TUD

S A

ND

NU

TS

16-

Rea

ctor

Coo

lant

Pum

p 1A

seal

cov

er1.

1” x

8.2

7”V

T-1

1616

****

**V

T-1

exam

s r

equi

red

once

per

inte

rval

(B-L

-2)

17-

Rea

ctor

Coo

lant

Pum

p 1B

seal

cov

er1.

1” x

8.2

7”V

T-1

1616

****

18-

Rea

ctor

Coo

lant

Pum

p 2A

seal

cov

er1.

1” x

8.2

7”V

T-1

1616

****

19-

Rea

ctor

Coo

lant

Pum

p 2B

seal

cov

er1.

1” x

8.2

7”V

T-1

1616

****

VA

LVE

S

Whe

n di

sass

embl

ed a

nd

only

onc

e pe

r int

erva

l. O

ne b

olte

d co

nnec

tion

amon

g a

grou

p of

sim

ilar

bolte

d co

nnec

tions

. B

7.70

BO

LTS

, STU

DS

AN

D N

UTS

30-

Aux

Pre

ssur

izer

Spr

ayH

V-2

03C

H-5

21-2

”V

T-1

11

****

**V

T-1

exam

s(4

set

s of

bol

ting

per v

alve

)H

V-2

05C

H-5

20-2

”V

T-1

11

****

requ

ired

once

per

inte

rval

AC

T 44

2489

1

31-

Pre

ssur

izer

Saf

etie

sP

SV

-200

RC

-001

-6”

VT-

11

1**

****

*D

urin

g V

EN

DO

R

disa

ssem

bly

(B-M

-2)

(12

sets

of b

oltin

g pe

r val

ve)

PS

V-2

01R

C-0

03-6

”V

T-1

11

****

***

AC

T 44

2489

1P

SV

-202

RC

-005

-6”

VT-

11

1**

****

*P

SV

-203

RC

-007

-6”

VT-

11

1**

****

*

CR

D H

OU

SIN

G

****

Whe

n di

sass

embl

ed a

nd

only

onc

e pe

r in

terv

alB

7.80

BO

LTS

, STU

DS

AN

D N

UTS

Use

199

5 ed

. Per

2-C

losu

re H

ead

RV

LMS

Loc

atio

nsG

rayl

oc C

lam

psC

ED

M 9

2V

T-1

44

****

****

50.5

5a (b

)(2)

(xxi

)(B

).C

ED

M 9

6V

T-1

44

****

****

22 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 23: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-J

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN P

IPIN

GB

9.10

NP

S 4

OR

LA

RG

ER

B9.

11*

CIR

CU

MFE

RE

NTI

AL

WE

LDS

6-

RC

S P

rimar

y P

ipin

gH

L 1*

*bu

tt w

elds

RC

-032

-42”

IDS

* &

Vol

626

110

** A

UTO

EX

AM

OF

HL

2**

butt

wel

dsR

C-0

63-4

2” ID

62

19N

OZZ

LE T

O E

XT

AN

DC

L 1A

to R

CP

butt

wel

dsR

C-0

33-3

0” ID

73

31E

XT

TO P

IPE

WE

LDS

CL

1B to

RC

Pbu

tt w

elds

RC

-030

-30”

IDC

L 2A

to R

CP

butt

wel

dsR

C-0

73-3

0” ID

*Sur

face

exa

ms

not

CL

2B to

RC

Pbu

tt w

elds

RC

-084

-30”

IDre

quire

d in

con

junc

tion

CL

1A to

RP

V**

butt

wel

dsR

C-0

34-3

0” ID

with

aut

o ex

amin

atio

nC

L 1B

to R

PV

**bu

tt w

elds

RC

-031

-30”

ID(E

WR

-367

3722

&

CL

2A to

RP

V**

butt

wel

dsR

C-0

79-3

0” ID

Cod

e C

ase

N66

3)C

L 2B

to R

PV

**bu

tt w

elds

RC

-093

-30”

ID

20-

Pre

ssur

izer

Sur

ge L

ine

butt

wel

dsR

C-0

28-1

2”S

& V

ol12

11

8D

M M

oved

to A

UG

;1

216

See

als

o A

UG

_Ite

m F

.1

325

21-

Shu

tdow

n C

oolin

g Lo

op 1

butt

wel

dsR

C-0

51-1

6"S

& V

ol25

31

12D

M M

oved

to A

UG

;

S

I-240

-16”

0

212

See

als

o A

UG

_Ite

m F

.

33

24A

CT

4424

891

22-

Shu

tdow

n C

oolin

g Lo

op 2

butt

wel

dsR

C-0

68-1

6”S

& V

ol19

21

10D

M M

oved

to A

UG

;S

I-193

-16"

72

47S

ee a

lso

AU

G_I

tem

F.

03

47A

CT

4424

891

23-

Saf

ety

Inje

ctio

n 1A

butt

wel

dsS

I-207

-14”

S &

Vol

195

126

DM

Mov

ed to

AU

G;

SI-2

03-1

2”S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

24-

Saf

ety

Inje

ctio

n 1B

butt

wel

dsS

I-223

-14”

S &

Vol

185

228

DM

Mov

ed to

AU

G;

SI-2

21-1

2”S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

23 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 24: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

25-

Saf

ety

Inje

ctio

n 2A

butt

wel

dsS

I-160

-14”

S &

Vol

226

327

DM

Mov

ed to

AU

G;

SI-1

56-1

2”S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

26-

Saf

ety

Inje

ctio

n 2B

butt

wel

dsS

I-179

-14”

S &

Vol

185

328

DM

Mov

ed to

AU

G;

SI-1

75-1

2”S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

28 &

29-

Pre

ssur

izer

Spr

aybu

tt w

elds

RC

-018

-4”

S &

Vol

151

17

12

142

327

31-

Pre

ssur

izer

Saf

etie

sbu

tt w

elds

RC

-001

-6”

S &

Vol

121

18

RC

-003

-6”

12

17R

C-0

05-6

”1

325

RC

-007

-6”

36-

Let

dow

n Li

ne (d

elay

coi

l)bu

tt w

elds

RC

-091

-16”

S &

Vol

41

325

24 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 25: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

B9.

20LE

SS

TH

AN

NP

S 4

B9.

21*

CIR

CU

MFE

RE

NTI

AL

WE

LDS

O

THE

R T

HA

N P

WR

HP

SI S

YS

TEM

S

27-

Pre

ssur

izer

Spr

ay 1

Abu

tt w

elds

RC

-062

-3”

S40

111

27D

M M

oved

to A

UG

;R

C-0

16-3

”S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

28-

Pre

ssur

izer

Spr

ay 1

Bbu

tt w

elds

RC

-017

-3”

S37

103

27D

M M

oved

to A

UG

;R

C-0

18-3

”S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

30-

Aux

Pre

ssur

izer

Spr

aybu

tt w

elds

CH

-009

-2”

S11

32

30C

H-5

20-2

”C

H-5

21-2

32-

Dra

in L

ine

Loop

1A

butt

wel

dsR

C-0

60-2

”S

62

133

DM

Mov

ed to

AU

G;

S

ee a

lso

AU

G_I

tem

B&

AU

G_B

15.2

15.

33-

Dra

in L

ine

Loop

1B

butt

wel

dsR

C-0

58-2

”S

62

233

DM

Mov

ed to

AU

G;

See

als

o A

UG

_Ite

m B

& A

UG

_B15

.215

.

34-

Dra

in L

ine

Loop

2A

butt

wel

dsR

C-0

96-2

”S

62

333

DM

Mov

ed to

AU

G;

See

als

o A

UG

_Ite

m B

& A

UG

_B15

.215

.

35-

Dra

in L

ine

Loop

2B

butt

wel

dsR

C-0

89-2

”S

52

340

36-

Let

dow

n Li

nebu

tt w

elds

RC

-091

-2”

S71

61

8D

M M

oved

to A

UG

;C

H-0

01-2

”6

216

See

als

o A

UG

_Ite

m B

63

25&

AU

G_B

15.2

15.

37-

Cha

rgin

g Li

nebu

tt w

elds

CH

-005

-3”

S62

51

8D

M M

oved

to A

UG

;C

H-0

05-2

”5

216

See

als

o A

UG

_Ite

m B

63

26&

AU

G_B

15.2

15.

25 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 26: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

38-

Dra

in L

ine

Loop

1bu

tt w

elds

RC

-070

-2”

S1

12

100

B9.

22C

IRC

UM

FER

EN

TIA

L W

ELD

S O

F P

WR

HP

SI S

YS

TEM

S* 9

.22

runn

ing

perc

ent

--

-77

31

3A

CT

4424

891

102

168

327

39-

HP

SI L

ong

Term

Rec

ircul

atio

n 1

butt

wel

dsS

I-248

-3”

Vol

530

2A

CT

4424

891

83

40-

HP

SI L

ong

Term

Rec

ircul

atio

n 2

butt

wel

dsS

I-199

-3”

Vol

243

1A

CT

4424

891

102

26 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 27: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

B9.

30B

RA

NC

H P

IPE

CO

NN

EC

TIO

N

WE

LDS

B9.

31N

PS

4 O

R L

AR

GE

R* 9

.31

runn

ing

perc

ent

--

-7

11

141

328

6-

RC

S P

rimar

y P

ipin

gS

urge

bran

ch w

eld

RC

-032

-42”

IDS

& V

ol1

SD

Coo

ling

1br

anch

wel

dR

C-0

32-4

2” ID

S &

Vol

1S

D C

oolin

g 2

bran

ch w

eld

RC

-063

-42”

IDS

& V

ol1

SI 1

Abr

anch

wel

dR

C-0

34-3

0” ID

S &

Vol

1S

I 1B

bran

ch w

eld

RC

-031

-30”

IDS

& V

ol1

SI 2

Abr

anch

wel

dR

C-0

79-3

0” ID

S &

Vol

1S

I 2B

bran

ch w

eld

RC

-093

-30”

IDS

& V

ol1

B9.

32LE

SS

TH

AN

NP

S 4

* 9.3

2 ru

nnin

g pe

rcen

t-

--

141

17

12

142

328

6-

RC

S P

rimar

y P

ipin

gD

rain

1A

bran

ch w

eld

RC

-033

-30”

IDS

1

PZR

Spr

ay 1

Abr

anch

wel

dR

C-0

34-3

0” ID

S

1D

rain

1B

bran

ch w

eld

RC

-030

-30”

IDS

1

PZR

Spr

ay 1

Bbr

anch

wel

dR

C-0

31-3

0” ID

S

1D

rain

2A

bran

ch w

eld

RC

-073

-30”

IDS

1

Cha

rgin

gbr

anch

wel

dR

C-0

79-3

0” ID

S

1Le

tdow

nbr

anch

wel

dR

C-0

84-3

0” ID

S

1

21-

Shu

tdow

n C

oolin

g Lo

op 1

bran

ch w

eld

RC

-051

-16”

S1

2” D

rain

& 3

" HP

SI

SI-2

40-1

6”1

22-

Shu

tdow

n C

oolin

g Lo

op 2

bran

ch w

eld

RC

-068

-16”

S1

3" H

PS

I

36-

Let

dow

n Li

nebr

anch

wel

dR

C-0

91-1

6”S

4

27 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 28: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

B9.

40S

OC

KE

T W

ELD

S* 9

.40

runn

ing

perc

ent

--

-21

21

9A

CT

4424

891

22

192

328

30-

Aux

Pre

ssur

izer

Spr

aybu

tt w

elds

CH

-520

-2”

S4

CH

-521

-2”

32-

Dra

in L

ine

Loop

1A

sock

et w

eld

RC

-060

-2”

S3

33-

Dra

in L

ine

Loop

1B

sock

et w

eld

RC

-058

-2”

S3

34-

Dra

in L

ine

Loop

2A

sock

et w

eld

RC

-096

-2”

S3

35-

Dra

in L

ine

Loop

2B

sock

et w

eld

RC

-089

-2”

S3

37-

Cha

rgin

gso

cket

wel

dR

C-0

05-3

"S

4

38-

Dra

in L

ine

Loop

1so

cket

wel

dR

C-0

70-2

”S

1

28 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 29: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-K

; WEL

DED

A

TTA

CH

MEN

TS F

OR

VES

SELS

. PIP

ING

, PU

MPS

AN

D V

ALV

ES

P

RE

SS

UR

E V

ES

SE

LSB

10.1

0W

ELD

ED

ATT

AC

HM

EN

TS**

Acc

essi

ble

Sid

e

3- S

team

Gen

erat

or 1

*su

ppor

t ski

rt24

2S

**1

12

50*

Mul

tiple

ves

sels

4 -S

team

Gen

erat

or 2

*su

ppor

t ski

rt24

3S

**1

5- P

ress

uriz

ersu

ppor

t ski

rt65

373

S**

11

110

0

PIP

ING

B10

.20

WE

LDE

D A

TTA

CH

ME

NTS

*B10

.20

runn

ing

perc

ent

--

-12

11

81

317

22-

Shu

tdow

n C

oolin

g 2

atta

chm

ent

SI-1

93-1

6”S

1R

C-0

68-1

6"S

1

27-

PZR

Spr

ay 1

Aat

tach

men

tR

C-0

62-3

"S

1 28

- P

ZR S

pray

1B

atta

chm

ent

RC

-017

-3"

S1

36-

Let

dow

n Li

neat

tach

men

tR

C-0

91-1

6”S

2R

C-0

91-2

”2

37-

Cha

rgin

g Li

neat

tach

men

tC

H-0

05-3

"S

3

40-

HP

SI L

ong

Term

2at

tach

men

tS

I-199

-3"

S1

29 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 30: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-L

-1, P

RES

SUR

E R

ETA

ININ

G W

ELD

S IN

PU

MP

CA

SIN

GS;

B-M

-1,

PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN V

ALV

E B

OD

IES;

B-L

-2, P

UM

P C

ASI

NG

S; B

-M-2

, VA

LVE

BO

DIE

S

EX

AM

CA

TEG

OR

IES

B-

L-1

and

B-M

-1 d

elet

ed in

th

e 20

07 E

d., 2

008

Add

. S

ee le

tter 1

02-0

6454

an

d S

ER

dat

ed

09/1

8/20

12.

B12

.20

PU

MP

CA

SIN

G16

- R

eact

or C

oola

nt P

ump

1Aca

sing

1111

-1A

VT-

34

1*

*E

xam

requ

ired

whe

n17

- R

eact

or C

oola

nt P

ump

1Bca

sing

1111

-1B

VT-

3pu

mp

is d

isas

sem

bled

18-

Rea

ctor

Coo

lant

Pum

p 2A

casi

ng11

11-2

AV

T-3

19-

Rea

ctor

Coo

lant

Pum

p 2B

casi

ng11

11-2

BV

T-3

B12

.50

VA

LVE

BO

DY

, EX

CE

ED

ING

NP

S 4

16" B

org

War

ner G

ate

Val

ves

Util

izin

g Fo

rged

Con

stru

ctio

nZo

ne 2

1U

V-6

51R

C-0

51-1

6”V

T-3

41

**

Exa

m re

quire

d w

hen

UV

-653

SI-2

40-1

6”V

T-3

valv

e is

dis

asse

mbl

edZo

ne 2

2U

V-6

52R

C-0

68-1

6”V

T-3

UV

-654

SI-1

93-1

6”V

T-3

14" B

org

War

ner G

ate

Val

ves

Util

izin

g Fo

rged

Con

stru

ctio

nZo

ne 2

3U

V-6

34S

I-207

-14”

VT-

34

1*

*E

xam

requ

ired

whe

nZo

ne 2

4U

V-6

44S

I-223

-14”

VT-

3va

lve

is d

isas

sem

bled

Zone

25

UV

-614

SI-1

60-1

4”V

T-3

Zone

26

UV

-624

SI-1

79-1

4”V

T-3

30 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 31: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

12" B

org

War

ner C

heck

Val

ves

Util

izin

g C

ast C

onst

ruct

ion

Zone

23

V-5

42S

I-203

-12"

VT-

34

1*

*E

xam

requ

ired

whe

nZo

ne 2

4V

-543

SI-2

21-1

2”V

T-3

valv

e is

dis

asse

mbl

edZo

ne 2

5V

-540

SI-1

56-1

2”V

T-3

Zone

26

V-5

41S

I-175

-12”

VT-

3

14" B

org

War

ner C

heck

Val

ves

Util

izin

g C

ast C

onst

ruct

ion

Zone

23

V-2

35S

I-207

-14”

VT-

38

1*

*E

xam

requ

ired

whe

nV

-237

SI-2

07-1

4”V

T-3

valv

e is

dis

asse

mbl

edZo

ne 2

4V

-245

SI-2

23-1

4”V

T-3

V-2

47S

I-223

-14”

VT-

3Zo

ne 2

5V

-215

SI-1

60-1

4”V

T-3

V-2

17S

I-160

-14”

VT-

3Zo

ne 2

6V

-225

SI-1

79-1

4”V

T-3

V-2

27S

I-179

-14”

VT-

3

Dre

sser

PS

VU

tiliz

ing

Forg

ed C

onst

ruct

ion

Zone

31

PS

V-2

00R

C-0

01-6

”V

T-3

41

**

Exa

m re

quire

d w

hen

PS

V-2

01R

C-0

03-6

”V

T-3

valv

e is

dis

asse

mbl

edP

SV

-202

RC

-005

-6”

VT-

3P

SV

-203

RC

-007

-6”

VT-

3

31 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 32: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-N

-1, I

NTE

RIO

R O

F R

EAC

TOR

VES

SEL;

B-N

-2, W

ELD

ED C

OR

E SU

PPO

RT

STR

UC

TUR

ES A

ND

INTE

RIO

R

ATT

AC

HM

ENTS

TO

REA

CTO

R V

ESSE

LS; B

-N

-3, R

EMO

VAB

LE C

OR

E SU

PPO

RT

STR

UC

TUR

ESB

13.1

0V

ES

SE

L IN

TER

IOR

At 3

yea

r int

erva

ls1-

R

eact

or V

esse

lac

cess

ible

are

as65

173

VT-

31

11

100

R15

, R17

, and

R19

12

100

13

100

B13

.50

INTE

RIO

R A

TTA

CH

ME

NTS

WIT

HIN

BE

LTLI

NE

RE

GIO

N1-

R

eact

or V

esse

lac

cess

ible

wel

ds65

173

VT-

11

13

100

B13

.60

INTE

RIO

R A

TTA

CH

ME

NTS

BE

YO

ND

BE

LTLI

NE

RE

GIO

N1-

R

eact

or V

esse

lac

cess

ible

wel

ds65

173

VT-

31

03

020

28 (n

ote

RR

44)

B13

.70

CO

RE

SU

PP

OR

T S

TRU

CTU

RE

1-

Rea

ctor

Ves

sel

acce

ssib

le a

reas

6517

3V

T-3

10

30

2028

(not

e R

R 4

4)

32 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 33: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-O

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN C

ON

TRO

L R

OD

H

OU

SIN

GS

*exa

m c

ateg

ory

runn

ing

perc

ent

--

-12

60

1*

*Rep

lace

d R

V H

ead

02

3R

1510

38

B14

.10

WE

LDS

IN C

RD

HO

US

ING

32 p

erip

heria

l2-

R

eact

or V

esse

lLo

wer

Hou

sing

66 th

ru 9

7S

or V

ol32

Clo

sure

Hea

dC

ED

M H

ousi

ngs

2-

Rea

ctor

Ves

sel

Upp

er H

ousi

ng66

thru

97

S o

r Vol

32C

losu

re H

ead

CE

DM

Hou

sing

s2-

R

eact

or V

esse

lLo

wer

Tub

e66

-91,

93-9

5,97

S o

r Vol

30C

losu

re H

ead

RV

LMS

92 a

nd 9

6S

or V

ol2

CE

DM

Hou

sing

s2-

R

eact

or V

esse

lU

pper

Tub

e66

-91,

93-9

5,97

S o

r Vol

30C

losu

re H

ead

CE

DM

Hou

sing

s

EXA

M C

ATE

GO

RY

B-P

; ALL

PR

ESSU

RE

RET

AIN

ING

CO

MPO

NEN

TSN

ote

Aug

men

ted

for V

T-2

of in

sula

ted

bolti

ngB

15.1

0P

RE

SS

UR

E R

ETA

ININ

GC

lass

1IW

B-5

222a

VT-

2*

**

**N

OTE

Pre

ssur

e Te

stC

OM

PO

NE

NTS

Pro

gram

B15

.10

PR

ES

SU

RE

RE

TAIN

ING

Cla

ss 1

IWB

-522

2bV

T-2

****

****

**N

OTE

Pre

ssur

e Te

stC

OM

PO

NE

NTS

Pro

gram

EXA

M C

ATE

GO

RY

B-Q

; STE

AM

G

ENER

ATO

R T

UB

ING

*Gov

erne

d by

Pla

nt

Tech

Spe

cific

atio

nsB

16.2

0S

TEA

M G

EN

ER

ATO

R T

UB

ING

IN*

**

**

**

U-T

UB

E D

ES

IGN

33 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 34: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

F-A

; SU

PPO

RTS

F1

.10

CLA

SS

1 P

IPIN

G S

UP

PO

RTS

RE

STR

AIN

TS*F

-A; B

runn

ing

perc

ent

none

F1.1

0C

LAS

S 1

PIP

ING

SU

PP

OR

TSB

-MU

LTID

IRE

CTI

ON

AL

RE

STR

AIN

TS*F

-A; B

runn

ing

perc

ent

--

-84

71

88

218

83

27

20-

Pre

ssur

izer

Sur

ge L

ine

supp

orts

RC

-28-

12”

VT-

31

21-

Shu

tdow

n C

oolin

g 1

supp

orts

RC

-51-

16”

VT-

32

SI-2

40-1

6”V

T-3

1122

- S

hutd

own

Coo

ling

2su

ppor

tsS

I-193

-16”

VT-

34

23-

Saf

ety

Inje

ctio

n 1A

supp

orts

SI-2

07-1

4”V

T-3

124

- S

afet

y In

ject

ion

1Bsu

ppor

tsS

I-223

-14”

VT-

31

25-

Saf

ety

Inje

ctio

n 2A

supp

orts

SI-1

56-1

2”V

T-3

126

- S

afet

y In

ject

ion

2Bsu

ppor

tsS

I-179

-14”

VT-

31

SI-1

75-1

2”V

T-3

127

- P

ress

uriz

er S

pray

1A

supp

orts

RC

-62-

3”V

T-3

7R

C-1

6-3”

VT-

31

28-

Pre

ssur

izer

Spr

ay 1

Bsu

ppor

tsR

C-1

7-3”

VT-

38

RC

-18-

3”V

T-3

1R

C-1

8-4”

VT-

31

30-

Aux

Pre

ssur

izer

Spr

aysu

ppor

tsC

H-5

21-2

”V

T-3

132

- D

rain

Lin

e 1A

supp

orts

RC

-60-

2”V

T-3

133

- D

rain

Lin

e 1B

supp

orts

RC

-58-

2”V

T-3

136

- L

etdo

wn

Line

supp

orts

RC

-91-

2”V

T-3

12C

H-1

-2”

VT-

31

RC

-91-

16”

VT-

32

37-

Cha

rgin

g Li

nesu

ppor

tsC

H-5

-3”

VT-

315

39-

HP

SI L

ong

Term

Rec

ircul

atio

n 1

supp

orts

SI-2

48-3

”V

T-3

740

- H

PS

I Lon

g Te

rm R

ecirc

ulat

ion

2su

ppor

tsS

I-199

-3”

VT-

33

34 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 35: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.1

0C

LAS

S 1

PIP

ING

SU

PP

OR

TSC

-SU

PP

OR

TS T

HA

T A

LLO

WTH

ER

MA

L M

OV

EM

EN

T (S

PR

ING

)*F

-A; C

runn

ing

perc

ent

--

-39

41

94

218

43

28

20-

Pre

ssur

izer

Sur

ge L

ine

supp

orts

RC

-28-

12”

VT-

33

21-

Shu

tdow

n C

oolin

g 1

supp

orts

SI-2

40-1

6”V

T-3

222

- S

hutd

own

Coo

ling

2su

ppor

tsR

C-6

8-16

”V

T-3

223

- S

afet

y In

ject

ion

1Asu

ppor

tsS

I-207

-14”

VT-

32

24-

Saf

ety

Inje

ctio

n 1B

supp

orts

SI-2

23-1

4”V

T-3

225

- S

afet

y In

ject

ion

2Asu

ppor

tsS

I-160

-14”

VT-

31

26-

Saf

ety

Inje

ctio

n 2B

supp

orts

SI-1

79-1

4”V

T-3

1S

I-175

-12”

VT-

31

27-

Pre

ssur

izer

Spr

ay 1

Asu

ppor

tsR

C-6

2-3”

VT-

33

28-

Pre

ssur

izer

Spr

ay 1

Bsu

ppor

tsR

C-1

7-3”

VT-

33

29-

Com

bine

d P

ress

uriz

er S

pray

supp

orts

RC

-18-

4”V

T-3

330

- A

ux P

ress

uriz

er S

pray

supp

orts

CH

-521

-2”

VT-

31

37-

Cha

rgin

g Li

nesu

ppor

tsC

H-5

-3”

VT-

39

39-

HP

SI L

ong

Term

Rec

ircul

atio

n 1

supp

orts

SI-2

48-3

”V

T-3

340

- H

PS

I Lon

g Te

rm R

ecirc

ulat

ion

2su

ppor

tsS

I-199

-3”

VT-

31

35 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 36: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.4

0S

UP

PO

RTS

OTH

ER

TH

AN

PIP

ING

SU

PP

OR

TS*F

-A; B

runn

ing

perc

ent

--

-14

**4

128

**14

req'

d du

e to

4

256

mul

tiple

com

pone

nts

63

100

1 - R

eact

or V

esse

lco

lum

ns65

173

VT-

34

3 - S

team

Gen

erat

or 1

*sk

irt24

2V

T-3

1*m

ultip

le c

omp

4 - S

team

Gen

erat

or-2

*sk

irt24

3V

T-3

1

5 - P

ress

uriz

e rsk

irt65

373

VT-

31

16-

Rea

ctor

Coo

lant

Pum

p 1A

**co

lum

ns11

11-1

AV

T-3

4**

mul

tiple

com

pup

per h

orz

1111

-1A

VT-

32

low

er h

orz

1111

-1A

VT-

32

17-

Rea

ctor

Coo

lant

Pum

p 1B

**co

lum

ns11

11-1

BV

T-3

4up

per h

orz

1111

-1B

VT-

32

low

er h

orz

1111

-1B

VT-

32

18-

Rea

ctor

Coo

lant

Pum

p 2A

**co

lum

ns11

11-2

AV

T-3

4up

per h

orz

1111

-2A

VT-

32

low

er h

orz

1111

-2A

VT-

32

19-

Rea

ctor

Coo

lant

Pum

p 2B

**co

lum

ns11

11-2

BV

T-3

4up

per h

orz

1111

-2B

VT-

32

low

er h

orz

1111

-2B

VT-

32

36 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 37: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.4

0S

UP

PO

RTS

OTH

ER

TH

AN

PIP

ING

SU

PP

OR

TS*F

-A; C

runn

ing

perc

ent

--

-8*

*1

250

**2

req'

d du

e to

1

310

0m

ultip

le c

ompo

nent

s

16-

Rea

ctor

Coo

lant

Pum

p 1A

**sn

ubbe

rs11

11-1

AV

T-3

2**

mul

tiple

com

p

17-

Rea

ctor

Coo

lant

Pum

p 1B

**sn

ubbe

rs11

11-1

BV

T-3

2

18-

Rea

ctor

Coo

lant

Pum

p 2A

**sn

ubbe

rs11

11-2

AV

T-3

2

19-

Rea

ctor

Coo

lant

Pum

p 2B

**sn

ubbe

rs11

11-2

BV

T-3

2

37 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 38: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 5.0 ASME CLASS 2

EXAMINATION SUMMARY

38 of 212 3INT-ISI-3, Rev. 3

Page 39: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

INDEX

EXAM CATEGORY

C-A Pressure Retaining Welds in Pressure Vessels

C-B Pressure Retaining Nozzle Welds in Vessels

C-C Welded Attachments for Vessels, Piping, Pumps, and Valves

C-D Pressure Retaining Bolting Greater than 2 Inch in Diameter

C-F-1 Pressure Retaining Welds in Austenitic Stainless Steel or High Alloy Piping

C-F-2 Pressure Retaining Welds in Carbon or Low Alloy Steel Piping

C-G Pressure Retaining Welds in Pumps and Valves

C-H All Pressure Retaining Components

F-A Class 2 Supports

39 of 212 3INT-ISI-3, Rev. 3

Page 40: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-A

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN P

RES

SUR

E VE

SSEL

S

*cat

egor

y ru

nnin

g pe

rcen

t-

--

23**

41

23**

23 T

otal

, 17

RE

Q'D

82

71m

ultip

le v

esse

ls5

310

0

STE

AM

GE

NE

RA

TOR

SC

1.10

SH

ELL

CIR

CU

MFE

RE

NTI

AL

WE

LDS

(she

ll to

con

ical

sec

tion)

41-

Ste

am G

ener

ator

1w

elds

242

Vol

22

2*

42

- S

team

Gen

erat

or 2

wel

ds24

3V

ol2

C1.

20H

EA

D C

IRC

UM

FER

EN

TIA

L W

ELD

S(h

ead

to s

hell)

41-

Ste

am G

ener

ator

1w

elds

242

Vol

11

2*

42-

Ste

am G

ener

ator

2w

elds

243

Vol

1

C1.

30TU

BE

SH

EE

T-TO

-SH

ELL

WE

LDS

41-

Ste

am G

ener

ator

1w

elds

242

Vol

11

2*

42-

Ste

am G

ener

ator

2w

elds

243

Vol

1

R

EG

EN

ER

ATI

VE

HE

AT

EX

CH

AN

GE

RC

1.10

SH

ELL

CIR

CU

MFE

RE

NTI

AL

WE

LDS

68

- R

egen

erat

ive

Hea

t Exc

hang

erw

elds

7931

4V

ol3

33

*

C

1.20

HE

AD

CIR

CU

MFE

RE

NTI

AL

WE

LDS

68

- R

egen

erat

ive

Hea

t Exc

hang

erw

elds

7931

4V

ol2

23

*

C1.

30TU

BE

SH

EE

T-TO

-SH

ELL

WE

LDS

68-

Reg

ener

ativ

e H

eat E

xcha

nger

wel

ds79

314

Vol

44

2*

40 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 41: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

LE

TDO

WN

HE

AT

EX

CH

AN

GE

RC

1.10

SH

ELL

CIR

CU

MFE

RE

NTI

AL

WE

LDS

69

- L

etdo

wn

Hea

t Exc

hang

erw

elds

N23

76V

ol1

11

*

C

1.30

TUB

ES

HE

ET-

TO-S

HE

LL W

ELD

S

69-

Let

dow

n H

eat E

xcha

nger

wel

dsN

2376

Vol

11

1*

S

HU

TDO

WN

CO

OLI

NG

HE

AT

EX

CH

C1.

10S

HE

LL C

IRC

UM

FER

EN

TIA

L W

ELD

S(s

hell

to fl

ange

)84

- S

DC

HX

Aw

elds

S-1

8345

Vol

11

1*

87

- S

DC

HX

Bw

elds

S-1

8346

Vol

1

C1.

30TU

BE

SH

EE

T-TO

-SH

ELL

WE

LDS

84-

SD

CH

X A

wel

dsS

-183

45V

ol1

11

* 87

- S

DC

HX

Bw

elds

S-1

8346

Vol

1

41 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 42: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-B

; PR

ESSU

RE

RET

AIN

ING

NO

ZZLE

WEL

DS

IN V

ESSE

LS

C2.

20N

OZZ

LES

WIT

HO

UT

RE

INFO

RC

ING

PLA

TE IN

VE

SS

ELS

>1/

2 IN

. N

OM

INA

L TH

ICK

NE

SS

C2.

21N

OZZ

LE-T

O-S

HE

LL (N

OZZ

LE T

O

HE

AD

OR

NO

ZZLE

TO

NO

ZZLE

) W

ELD

*C2.

21 ru

nnin

g pe

rcen

t-

--

20**

21

20**

20

Tota

l, 10

RE

Q'D

42

60m

ultip

le v

esse

ls4

310

0 41

- S

team

Gen

erat

or 1

wel

ds24

2S

& V

ol8

42

42

- S

team

Gen

erat

or 2

wel

ds24

3S

& V

ol8

43

84-

SD

CH

X A

wel

dsS

-183

45S

& V

ol2

11

87-

SD

CH

X B

wel

dsS

-183

46S

& V

ol2

11

C

2.22

NO

ZZLE

INS

IDE

RA

DIU

S S

EC

TIO

N*C

2.22

runn

ing

perc

ent

--

-12

**2

133

** 1

2 To

tal,

6 R

EQ

'D2

267

mul

tiple

ves

sels

23

100

41-

Ste

am G

ener

ator

1w

elds

242

Vol

42

2

42-

Ste

am G

ener

ator

2w

elds

243

Vol

42

3

84-

SD

CH

X A

wel

dsS

-183

45V

ol2

11

87-

SD

CH

X B

wel

dsS

-183

46V

ol2

11

42 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 43: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-C

; WEL

DED

A

TTA

CH

MEN

TS F

OR

VES

SELS

, PIP

ING

, PU

MPS

, AN

D V

ALV

ES

P

RE

SS

UR

E V

ES

SE

LSC

3.10

WE

LDE

D A

TTA

CH

ME

NTS

*C3.

10 ru

nnin

g pe

rcen

t-

--

6**

21

** 6

Tot

al; 4

RE

QD

23

Mul

tiple

Ves

sels

Mul

tiple

Ves

sels

41-

Ste

am G

ener

ator

1lu

gs24

2S

22

1

42-

Ste

am G

ener

ator

2lu

gs24

3S

2

68-

Reg

ener

ativ

e H

eat E

xcha

nger

supp

orts

7931

4S

22

3

PIP

ING

C

3.20

WE

LDE

D A

TTA

CH

ME

NTS

*C3.

20 ru

nnin

g pe

rcen

t-

--

301

111

3

10

27

12

310

43-

Mai

n S

team

SG

1 E

ast

atta

chm

ent

SG

-036

S2

44-

Mai

n S

team

SG

1 W

est

atta

chm

ent

SG

-033

S2

45-

Mai

n S

team

SG

2 E

ast

atta

chm

ent

SG

-042

S2

46-

Mai

n S

team

SG

2 W

est

atta

chm

ent

SG

-045

S2

54-

Fee

dwat

er S

G N

o. 1

atta

chm

ent

SG

-002

S6

55-

Fee

dwat

er S

G N

o. 2

atta

chm

ent

SG

-005

S6

11

56-

Fee

dwat

er S

G N

o. 1

atta

chm

ent

SG

-202

S1

57-

Fee

dwat

er S

G N

o. 2

atta

chm

ent

SG

-205

S1

58-

Aux

Fee

d S

/G 1

atta

chm

ent

SG

-008

S1

43 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 44: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

59-

Aux

Fee

d S

/G 2

atta

chm

ent

SG

-011

S2

62-

Aux

iliar

y Fe

edw

ater

SG

1at

tach

men

tA

F-01

8S

1

63-

Aux

iliar

y Fe

edw

ater

SG

2at

tach

men

tA

F-01

6S

11

1

64-

Blo

wdo

wn

SG

1at

tach

men

tS

G-0

39S

61

2S

G-0

53S

1

65-

Blo

wdo

wn

SG

2at

tach

men

tS

G-0

48S

61

2S

G-0

52S

1

70-

LP

SI P

ump

Roo

m A

Suc

tion

atta

chm

ent

SI-0

67S

1

SI-2

41S

1S

I-307

S1

71-

LP

SI P

ump

Roo

m A

Dis

char

geat

tach

men

tS

I-078

S3

SI-0

871

73-

LP

SI P

ump

Roo

m B

Suc

tion

atta

chm

ent

SI-0

34S

1

SI-3

08S

1

74-

LP

SI P

ump

Roo

m B

Dis

char

geat

tach

men

tS

I-129

S3

76-

CS

Pum

p R

oom

A S

uctio

nat

tach

men

tS

I-009

S1

SI-0

67S

1

77-

CS

Pum

p R

oom

A D

isch

arge

atta

chm

ent

SI-0

79S

51

3S

I-082

S1

79-

CS

Pum

p R

oom

B S

uctio

nat

tach

men

tS

I-033

S1

80-

CS

Pum

p R

oom

B D

isch

arge

atta

chm

ent

SI-1

19S

4

82-

SD

CH

X R

oom

Aat

tach

men

tS

I-078

S2

SI-0

79S

1

44 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 45: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

83-

SD

CH

X R

oom

Bat

tach

men

tS

I-070

S4

21

SI-0

82S

1S

I-087

S2

SI-0

89S

2S

I-090

S2

85-

SD

CH

X R

oom

Bat

tach

men

tS

I-119

S3

12

SI-1

23S

3

86-

SD

CH

X R

oom

Bat

tach

men

tS

I-072

S4

23

SI-1

29S

3S

I-134

S3

SI-1

35S

2

88-

Eas

t Wra

pat

tach

men

tS

I-072

S3

SI-0

73S

1

89-

Eas

t Wra

pat

tach

men

tS

I-173

S1

SI-1

94S

2

90-

Eas

t Wra

pat

tach

men

tS

I-134

S1

91-

Wes

t Wra

pat

tach

men

tS

I-070

S4

92-

Wes

t Wra

pat

tach

men

tS

I-239

S1

11

SI-2

41S

3

93-

Wes

t Wra

pat

tach

men

tS

I-089

S1

94-

A T

rain

Pip

e C

hase

& 8

8'at

tach

men

tS

I-070

S3

12

SI-0

89S

2S

I-241

S4

95-

B T

rain

Pip

e C

hase

& 8

8'at

tach

men

tS

I-072

S1

13

SI-1

34S

2S

I-194

S6

45 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 46: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

96-

Con

tain

men

t LP

SI t

o 1A

atta

chm

ent

SI-2

02S

2

97-

Con

tain

men

t LP

SI t

o 1B

atta

chm

ent

SI-2

20S

3

98-

Con

tain

men

t LP

SI t

o 2A

atta

chm

ent

SI-1

55S

2

99-

Con

tain

men

t LP

SI t

o 2B

atta

chm

ent

SI-1

74S

21

2

100-

C

onta

inm

ent L

PS

I A S

uctio

nat

tach

men

tS

I-007

S1

SI-3

69S

1

101-

C

onta

inm

ent L

PS

I B S

uctio

nat

tach

men

tS

I-030

S1

SI-1

94S

1S

I-368

S1

102-

S

I Pum

p S

uctio

n A

atta

chm

ent

SI-0

08S

31

1S

I-009

S3

SI-3

07S

6

103-

R

efue

ling

Wat

er S

uctio

n A

atta

chm

ent

CH

-142

S6

12

CH

-424

S3

104-

S

I Pum

p S

uctio

n B

atta

chm

ent

SI-0

31S

2S

I-033

S1

SI-3

08S

7

105-

R

efue

ling

Wat

er S

uctio

n B

atta

chm

ent

CH

-149

S13

33

CH

-425

S2

106-

H

PS

I Roo

m D

isch

arge

Aat

tach

men

tS

I-099

S2

21

SI-1

00S

13

SI-1

05S

4S

I-106

S1

107-

H

PS

I Roo

m D

isch

arge

Bat

tach

men

tS

I-107

S11

32

S

I-112

S2

46 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 47: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

108-

H

PS

I 88’

Pip

echa

seat

tach

men

tS

I-100

S10

23

SI-1

18S

4

109-

H

PS

I 88’

Pip

echa

seat

tach

men

tS

I-107

S9

11

110-

H

PS

I Dis

char

ge W

est W

rap

atta

chm

ent

SI-1

03S

11

2

SI-1

07S

3S

I-218

S1

SI-2

36S

1

111-

H

PS

I Dis

char

ge W

est W

rap

atta

chm

ent

SI-1

00S

2

112-

H

PS

I Dis

char

ge E

ast W

rap

atta

chm

ent

SI-1

00S

1

SI-1

01S

1S

I-102

S1

SI-1

76S

1

113-

H

PS

I Dis

char

geat

tach

men

tS

I-107

S1

SI-1

57S

2S

I-176

S1

118-

H

PS

I Lon

g Te

rmat

tach

men

tS

I-106

S18

33

119-

H

PS

I Lon

g Te

rmat

tach

men

tS

I-114

S12

21

47 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 48: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

PU

MP

SC

3.30

WE

LDE

D A

TTA

CH

ME

NTS

*C3.

30 ru

nnin

g pe

rcen

t-

--

20**

12

10**

20 T

otal

, 10

RE

Q'D

Mul

tiple

Ves

sels

72-

LP

SI P

ump

Alu

gsS

N 0

876-

44S

3

75-

LP

SI P

ump

Blu

gsS

N 0

876-

45S

3

78-

Con

tain

men

t Spr

ay A

lugs

SN

087

6-46

S3

81-

Con

tain

men

t Spr

ay B

lugs

SN

087

6-47

S3

116-

HP

SI A

lugs

SN

077

6-19

S4

117-

HP

SI B

lugs

SN

077

6-18

S4

12

48 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 49: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-D

; PR

ESSU

RE

RET

AIN

ING

BO

LTIN

G G

REA

TER

TH

AN

2 in

. IN

DIA

MET

ER

*cat

egor

y ru

nnin

g pe

rcen

t-

--

10**

11

8**

10 T

otal

, 3 R

EQ

'D1

219

Mul

tiple

Item

s1

329

P

UM

PS

C4.

30B

OLT

S A

ND

STU

DS

116-

HP

SI A

stud

sS

N 0

776-

19V

OL

1

117-

HP

SI B

stud

sS

N 0

776-

18V

OL

11

1

V

ALV

ES

C4.

40B

OLT

S A

ND

STU

DS

47-

Mai

n S

team

SG

1 W

est

bonn

e tU

V-1

70V

OL

11

2

48-

Mai

n S

team

SG

1 E

ast

bonn

e tU

V-1

80V

OL

1

49-

Mai

n S

team

SG

2 E

ast

bonn

e tU

V-1

71V

OL

1

50-

Mai

n S

team

SG

2 W

est

bonn

e tU

V-1

81V

OL

1

56-

Fee

dwat

er S

G N

o. 1

bonn

e tU

V-1

32V

OL

11

3U

V-1

741

57-

Fee

dwat

er S

G N

o. 2

bonn

etU

V-1

37V

OL

1U

V-1

771

49 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 50: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-F

-1; P

RES

SUR

E R

ETA

ININ

G W

ELD

S IN

AU

STEN

ITIC

ST

AIN

LESS

STE

EL O

R H

IGH

ALL

OY

PIPI

NG

C5.

10

PIP

ING

WE

LDS

> 3

/8 IN

NO

MIN

AL

WA

LL T

HIC

KN

ES

S F

OR

PIP

ING

>N

PS

4C

5.11

CIR

CU

MFE

RE

NTI

AL

WE

LD*C

5.11

runn

ing

perc

ent

--

-50

020

12

*108

4 W

ELD

S U

SE

D22

24

FOR

% D

UE

TO

C-F

-140

38

NO

TE 2

58-A

ux F

eed

S/G

16”

x 0

.562

”A

F-00

4S

& V

ol17

41

DM

wel

d al

so fa

lls u

nder

A

UG

_C5.

11.

6” x

0.4

32”

SG

-008

8” x

0.5

00S

G-0

08

59-A

ux F

eed

S/G

26”

x 0

.562

”A

F-00

6S

& V

ol20

42

DM

wel

d al

so fa

lls u

nder

A

UG

_C5.

11.

6” x

0.4

32”

SG

-011

8” x

0.5

00S

G-0

11

62-A

ux F

eed

S/G

16”

x 0

.562

”A

F-00

4S

& V

ol18

33

AF-

018

63-A

ux F

eed

S/G

26”

x 0

.562

”A

F-00

6S

& V

ol16

31

AF-

016

70-L

PS

I Pum

p R

oom

A S

uctio

n20

” x 0

.375

SI-3

07S

& V

ol20

41

73-L

PS

I Pum

p R

oom

B S

uctio

nS

I-308

82 &

85

SD

C H

eat E

xch

20” x

0.5

00”

SI-0

78S

& V

ol9

11

AC

T 41

6263

7R

oom

A &

BS

I-123

12

50 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 51: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

83 &

86

SD

C H

eat E

xch

14” x

0.3

75”

SI-9

0S

& V

ol56

11

AC

T 41

6263

7R

oom

A &

BS

I-135

62

16” x

0.3

75”

SI-7

0S

I-72

20” x

0.5

00”

SI-7

0S

I-72

88 &

91

Saf

ety

Inje

ctio

n12

” x 0

.375

”S

I-72

S &

Vol

7912

3E

ast a

nd W

est W

raps

SI-7

3S

I-70

SI-7

112

” x 1

.125

”S

I-155

SI-1

74S

I-72

SI-7

3S

I-70

SI-7

1S

I-202

SI-2

2020

” x 0

.500

”S

I-72

SI-7

0 90

& 9

3 S

afet

y In

ject

ion

24” x

0.3

75”

SI-3

0S

& V

ol10

22

AC

T 41

6263

7E

ast a

nd W

est W

raps

SI-7

24” x

0.5

62”

SI-3

08S

I-307

94 &

95

Saf

ety

Inje

ctio

n A

& B

20” x

0.5

00S

I-70

S &

Vol

173

1S

I-72

51 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 52: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

96, 9

7, 9

8, 9

9 C

onta

inm

ent L

PS

I12

” x 1

.125

”S

I-202

S &

Vol

108

143

Loop

1A

, 1B

, 2A

& 2

BS

I-220

22

SI-1

55S

I-174

12” x

1.3

12”

SI-2

02S

I-220

SI-1

55S

I-174

100

& 1

01 C

onta

inm

ent L

PS

I16

” x 1

.594

SI-2

41S

& V

ol8

12

Loop

A &

B, S

uctio

nS

I-194

24” x

0.3

75S

I-7S

I-30

102-

Saf

ety

Inje

ctio

n A

Suc

tion

24” x

0.5

62”

SI-3

07S

& V

ol21

41

20” x

0.3

75”

SI-3

07

103-

Ref

uelin

g W

ater

Tan

k S

uctio

n A

20” x

0.3

75”

CH

-424

S &

Vol

356

220

” x 0

.375

”C

H-1

42

104-

Saf

ety

Inje

ctio

n B

Suc

tion

24” x

0.5

62”

SI-3

08S

& V

ol19

43

20” x

0.3

75”

SI-3

08

105-

Ref

uelin

g W

ater

Tan

k B

Suc

tion

20” x

0.3

75”

CH

-425

S &

Vol

477

320

” x 0

.375

”C

H-1

49

52 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 53: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

C5.

20

PIP

ING

WE

LDS

> 1

/5 IN

NO

MIN

AL

WA

LL T

HIC

KN

ES

S F

OR

PIP

ING

>

NP

S 2

AN

D <

NP

S 4

C5.

21C

IRC

UM

FER

EN

TIA

L W

ELD

*C5.

21 ru

nnin

g pe

rcen

t-

--

580

101

2

182

5

183

8

104

SI B

Tra

in S

uctio

n3”

X 0

.216

”C

H-1

50S

& V

ol4

13

106

& 1

07 H

PS

I Roo

m D

isch

arge

4” x

0.4

38”

SI-1

00S

& V

ol13

710

1A

and

B4”

x 0

.337

”S

I-99

SI-1

073”

x 0

.438

”S

I-106

SI-1

072”

x 0

.344

”S

I-105

SI-1

12

108

& 1

09 H

PS

I 88’

Pip

echa

se4”

x 0

.438

”S

I-100

S &

Vol

867

22”

x 0

344”

SI-1

184”

x 0

.377

”S

I-107

53 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 54: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

110

& 1

11 H

PS

I Dis

char

ge4”

x 0

.337

”S

I-107

S &

Vol

104

83

Wes

t Wra

p4”

x 0

.438

”S

I-218

SI-1

00S

I-236

3” x

0.4

38”

SI-2

18S

I-236

2” x

0.3

44”

SI-1

03S

I-107

SI-1

10S

I-218

SI-2

36S

I-100

112

& 1

13 H

PS

I Dis

char

ge4”

x 0

.337

”S

I-107

S &

Vol

998

2E

ast W

rap

4” x

0.4

38”

SI-1

00S

I-176

SI-1

573”

x 0

.438

”S

I-176

SI-1

572”

x 0

.344

”S

I-101

SI-1

02S

I-108

SI-1

09S

I-157

SI-1

76

114

& 1

15 H

PS

I Hea

der

3” x

0.4

38”

SI-2

18S

& V

ol44

32

Loop

1A

, 1B

, 2A

& 2

BS

I-236

SI-1

57S

I-176

118

& 1

19 H

PS

I Lon

g Te

rm3”

x 0

.438

”S

I-106

S &

Vol

106

93

SI-1

142”

x 0

.344

”S

I-319

54 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 55: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

C5.

30S

OC

KE

T W

ELD

S10

6 &

107

HP

SI R

oom

Dis

char

ge2”

x 0

.344

”S

I-105

S3

13

17A

and

BS

I-112

S3

C5.

40P

IPE

BR

AN

CH

CO

NN

EC

TIO

NS

OF

BR

AN

CH

PIP

ING

> N

PS

2C

5.41

CIR

CU

MFE

RE

NTI

AL

*C5.

41 ru

nnin

g pe

rcen

t-

--

271

14

1

27

1

311

82 &

85

SD

C H

eat E

xch

20” x

10”

SI-7

8S

21

1R

oom

A &

BS

I-123

S2

83 &

86

SD

C H

eat E

xch

20” x

6”

SI-7

0S

41

3R

oom

A &

B20

” x 1

0”S

I-72

S4

20” x

14”

88 &

91

Saf

ety

Inje

ctio

n20

” x 1

2”S

I-70

S1

Eas

t and

Wes

t Wra

psS

I-72

S1

89 &

92

SD

C S

uctio

n18

” x 1

2”S

I-194

S1

Eas

t and

Wes

t Wra

psS

I-241

S1

96, 9

7, 9

8, 9

9 C

onta

inm

ent L

PS

I12

” x 3

”S

I-202

S1

12

Loop

1A

, 1B

, 2A

& 2

BS

I-220

S1

SI-1

55S

1S

I-174

S1

102-

Saf

ety

Inje

ctio

n A

Suc

tion

24” x

10”

SI-3

07S

324

” x 1

8”24

” x 2

0”

104-

Saf

ety

Inje

ctio

n B

Suc

tion

24” x

10”

SI-3

08S

324

” x 1

8”24

” x 2

0”24

” x 3

”C

H-1

50S

1

55 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 56: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-F

-2; P

RES

SUR

E R

ETA

ININ

G W

ELD

S IN

CA

RB

ON

OR

LO

W

ALL

OY

STEE

L PI

PIN

G

** N

ote

exam

item

s ar

e in

Aug

Sum

mar

y un

der

AH

E5.

51

C5.

50

PIP

ING

WE

LDS

> 3

/8 IN

NO

MIN

AL

WA

LL T

HIC

KN

ES

S F

OR

PIP

ING

>N

PS

4C

5.51

CIR

CU

MFE

RE

NTI

AL

WE

LD*C

5.51

runn

ing

perc

ent

--

-33

88

12

102

510

38

43-

Mai

n S

team

SG

1 E

ast

But

t Wel

dsS

G-3

6-28

”S

& V

ol19

11

SG

-36-

32”

1

44-

Mai

n S

team

SG

1 W

est

But

t Wel

dsS

G-3

3-28

”S

& V

ol21

22

SG

-33-

32”

1

45-

Mai

n S

team

SG

2 E

ast

But

t Wel

dsS

G-4

2-28

”S

& V

ol19

13

SG

-42-

32”

1

46-

Mai

n S

team

SG

2 W

est

But

t Wel

dsS

G-4

5-28

”S

& V

ol21

21

SG

-45-

32”

1

47-

Mai

n S

team

SG

1 W

est

But

t Wel

ds**

S &

Vol

**

48-

Mai

n S

team

SG

1 E

ast

But

t Wel

ds**

S &

Vol

**

49-

Mai

n S

team

SG

2 E

ast

But

t Wel

ds**

S &

Vol

**

50-

Mai

n S

team

SG

2 W

est

But

t Wel

ds**

S &

Vol

**

51-

Atm

osph

eric

Dum

p N

o. 1

But

t Wel

ds**

S &

Vol

**

52-

Atm

osph

eric

Dum

p N

o. 2

But

t Wel

ds**

S &

Vol

**

53-

Ste

am to

Aux

Fee

dwat

erB

utt W

elds

**S

& V

ol**

56 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 57: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

54-

Fee

dwat

er S

G N

o. 1

But

t Wel

dsS

G-2

-24”

S &

Vol

304

3

Wel

ds 5

4-1

and

54-1

5 al

so fa

lls u

nder

A

UG

_C5.

51.

SG

-2-1

6”4

SG

-2-1

4”10

SG

-13-

16”

3S

G-1

3-14

”10

55-

Fee

dwat

er S

G N

o. 2

But

t Wel

dsS

G-5

-24”

S &

Vol

305

1

Wel

ds 5

5-1

and

55-1

5 al

so fa

lls u

nder

A

UG

_C5.

51.

SG

-5-1

6”3

SG

-5-1

4”10

SG

-14-

16”

3S

G-1

4-14

”10

56-

Fee

dwat

er S

G N

o. 1

But

t Wel

ds**

S &

Vol

**

57-

Fee

dwat

er S

G N

o. 2

But

t Wel

ds**

S &

Vol

**

58-

Aux

& D

ownc

omer

FW

SG

1B

utt W

elds

SG

-8-6

”S

& V

ol1

22

SG

-8-8

”22

59-

Aux

& D

ownc

omer

FW

SG

2B

utt W

elds

SG

-11-

6”S

& V

ol1

13

SG

-11-

8”20

60-

Dow

ncom

er F

eedw

ater

SG

1B

utt W

elds

**S

& V

ol**

61-

Dow

ncom

er F

eedw

ater

SG

2B

utt W

elds

**S

& V

ol**

64-

Blo

wdo

wn

SG

1B

utt W

elds

SG

-39-

6”S

& V

ol34

62

SG

-53-

6”13

SG

-522

-6”

1

65-

Blo

wdo

wn

SG

2B

utt W

elds

SG

-48-

6”S

& V

ol34

43

SG

-52-

6”14

SG

-523

-6”

1

57 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 58: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

66-

Blo

wdo

wn

SG

1B

utt W

elds

**S

& V

ol**

67-

Blo

wdo

wn

SG

2B

utt W

elds

**S

& V

ol**

C5.

80P

IPE

BR

AN

CH

CO

NN

EC

TIO

NS

OF

BR

AN

CH

PIP

ING

> N

PS

2

Sco

pe fr

om A

HE

5.81

m

oved

to C

5.81

. (C

RA

I 41

7827

7)C

5.81

CIR

CU

MFE

RE

NTI

AL

*C5.

81 ru

nnin

g pe

rcen

t-

--

301

13

AC

T 44

2489

11

26

23

13

47-

Mai

n S

team

SG

1 W

est

28” x

12”

SG

-206

-28”

S2

11

28” x

6”

5

48-

Mai

n S

team

SG

1 E

ast

28” x

12”

SG

-207

-28”

S2

12

28” x

6”

6

49-

Mai

n S

team

SG

2 E

ast

28” x

12”

SG

-208

-28”

S2

13

28” x

6”

6

50-

Mai

n S

team

SG

2 W

est

28” x

12”

SG

-209

-28”

S2

13

28” x

6”

5

EXA

M C

ATE

GO

RY

C-G

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN P

UM

PS A

ND

VA

LVES

EX

AM

CA

TEG

OR

Y C

-G

dele

ted

in th

e 20

07 E

d.,

2008

Add

. See

lette

r 102

-06

454

and

SE

R d

ated

09

/18/

2012

. (A

CT

4343

138)

58 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 59: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-H

; ALL

PR

ESSU

RE

RET

AIN

ING

CO

MPO

NEN

TS

C7.

10P

RE

SS

UR

E R

ETA

ININ

G

CO

MP

ON

EN

TSC

lass

2IW

C-5

222

VT-

2*

**

**N

OTE

Pre

ssur

e Te

st

Pro

gram

59 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 60: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

F-A

; SU

PPO

RTS

F1

.20

CLA

SS

2 P

IPIN

G S

UP

PO

RTS

A-O

NE

DIR

EC

TIO

NA

L (R

OD

S)

*F-A

; A ru

nnin

g pe

rcen

t-

--

41

225

65 -

Blo

wdo

wn

Ste

am G

ener

ator

#2

supp

orts

SI-4

8V

T-3

1

83-

SD

CH

X R

oom

Asu

ppor

tsS

I-87

VT-

31

12

106-

H

PS

I Roo

m D

isch

arge

Asu

ppor

tsS

I-100

VT-

31

107-

H

PS

I Roo

m D

isch

arge

Bsu

ppor

tsS

I-107

VT-

31

60 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 61: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.2

0C

LAS

S 2

PIP

ING

SU

PP

OR

TSR

ES

TRA

INTS

*F-A

; B ru

nnin

g pe

rcen

t-

--

418

221

514

29

283

15

43-

Mai

n S

team

SG

1 E

ast

supp

orts

SG

-36

VT-

32

11

44-

Mai

n S

team

SG

1 W

est

supp

orts

SG

-33

VT-

31

45-

Mai

n S

team

SG

2 E

ast

supp

orts

SG

-42

VT-

32

13

46-

Mai

n S

team

SG

2 W

est

supp

orts

SG

-45

VT-

31

54-

Fee

dwat

er S

G N

o. 1

supp

orts

SG

-002

VT-

35

11

55-

Fee

dwat

er S

G N

o. 2

supp

orts

SG

-005

VT-

35

11

58-

Aux

& D

ownc

omer

FW

SG

1su

ppor

tsS

G-8

VT-

35

12

59-

Aux

& D

ownc

omer

FW

SG

2su

ppor

tsS

G-1

1V

T-3

61

2

62-

Aux

iliar

y Fe

edw

ater

SG

1su

ppor

tsA

F-01

8V

T-3

11

1

63-

Aux

iliar

y Fe

edw

ater

SG

2su

ppor

tsA

F-00

6V

T-3

22

1A

F-01

6V

T-3

1

64-

Blo

wdo

wn

SG

1su

ppor

tsS

G-3

9V

T-3

101

1S

G-5

3V

T-3

1

65-

Blo

wdo

wn

SG

2su

ppor

tsS

G-4

8V

T-3

101

2S

G-5

2V

T-3

1

70-

LP

SI P

ump

Roo

m A

Suc

tion

supp

orts

SI-0

67V

T-3

1

SI-2

41V

T-3

1S

I-307

VT-

31

61 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 62: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

71-

LP

SI P

ump

Roo

m A

Dis

char

gesu

ppor

tsS

I-78

VT-

31

23

SI-8

7V

T-3

4

73-

LP

SI P

ump

Roo

m B

Suc

tion

supp

orts

SI-0

34V

T-3

21

1

SI-3

08V

T-3

1

74-

LP

SI P

ump

Roo

m B

Dis

char

gesu

ppor

tsS

I-129

VT-

33

76-

CS

Pum

p R

oom

A S

uctio

nsu

ppor

tsS

I-9V

T-3

1S

I-67

VT-

33

77-

CS

Pum

p R

oom

A D

isch

arge

supp

orts

SI-7

9V

T-3

62

3S

I-82

VT-

31

79-

CS

Pum

p R

oom

B S

uctio

nsu

ppor

tsS

I-033

VT-

31

23

SI-0

34V

T-3

2

80-

CS

Pum

p R

oom

B D

isch

arge

supp

orts

SI-1

19V

T-3

5

82-

SD

CH

X R

oom

Asu

ppor

tsS

I-78

VT-

31

SI-7

9V

T-3

1

83-

SD

CH

X R

oom

Asu

ppor

tsS

I-70

VT-

34

31

SI-8

2V

T-3

1S

I-87

VT-

32

SI-8

9V

T-3

4S

I-90

VT-

32

85-

SD

CH

X R

oom

Bsu

ppor

tsS

I-119

VT-

33

12

SI-1

23V

T-3

5

86-

SD

CH

X R

oom

Bsu

ppor

tsS

I-72

VT-

33

23

SI-1

29V

T-3

3S

I-134

VT-

32

SI-1

35V

T-3

1S

I-147

VT-

31

62 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 63: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

88-

Eas

t Wra

psu

ppor

tsS

I-72

VT-

34

SI-7

3V

T-3

1

89-

Eas

t Wra

psu

ppor

tsS

I-173

VT-

31

11

SI-1

94V

T-3

3

90-

Eas

t Wra

psu

ppor

tsS

I-130

VT-

31

SI-1

34V

T-3

2

91-

Wes

t Wra

psu

ppor

tsS

I-70

VT-

36

11

SI-7

1V

T-3

1

92-

Wes

t Wra

psu

ppor

tsS

I-241

VT-

35

11

93-

Wes

t Wra

psu

ppor

tsS

I-89

VT-

33

11

94-

A T

rain

Pip

e C

hase

& 8

8'su

ppor

tsS

I-70

VT-

33

12

SI-8

9V

T-3

3S

I-241

VT-

38

95-

B T

rain

Pip

e C

hase

& 8

8'su

ppor

tsS

I-72

VT-

31

33

SI-1

34V

T-3

3S

I-194

VT-

310

96-

Con

tain

men

t LP

SI t

o 1A

supp

orts

SI-2

02V

T-3

111

2

97-

Con

tain

men

t LP

SI t

o 1B

supp

orts

SI-2

20V

T-3

161

2

98-

Con

tain

men

t LP

SI t

o 2A

supp

orts

SI-1

55V

T-3

4

99-

Con

tain

men

t LP

SI t

o 2B

supp

orts

SI-1

74V

T-3

5

100-

C

onta

inm

ent L

PS

I A S

uctio

nsu

ppor

tsS

I-7V

T-3

1S

I-369

VT-

31

63 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 64: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

101-

C

onta

inm

ent L

PS

I B S

uctio

nsu

ppor

tsS

I-30

VT-

31

SI-1

94V

T-3

2S

I-368

VT-

31

102-

S

I Pum

p S

uctio

n A

supp

orts

SI-8

VT-

34

11

SI-9

VT-

33

SI-3

07V

T-3

7

103-

R

efue

ling

Wat

er S

uctio

n A

supp

orts

CH

-142

VT-

310

22

CH

-424

VT-

34

104-

S

I Pum

p S

uctio

n B

supp

orts

SI-3

1V

T-3

33

3S

I-33

VT-

31

SI-3

08V

T-3

8

105-

R

efue

ling

Wat

er S

uctio

n B

CH

-149

VT-

317

33

supp

orts

CH

-425

VT-

32

106-

H

PS

I Roo

m D

isch

arge

Asu

ppor

tsS

I-100

VT-

313

21

S

I-105

VT-

34

SI-1

06V

T-3

1

107-

H

PS

I Roo

m D

isch

arge

Bsu

ppor

tsS

I-107

VT-

310

32

S

I-112

VT-

33

108-

H

PS

I 88’

Pip

echa

sesu

ppor

tsS

I-100

VT-

310

23

SI-1

18V

T-3

6

109-

H

PS

I 88’

Pip

echa

sesu

ppor

tsS

I-107

VT-

311

11

110-

H

PS

I Dis

char

ge W

est W

rap

supp

orts

SI-1

03V

T-3

41

2

SI-1

07V

T-3

4S

I-110

VT-

31

SI-2

18V

T-3

3S

I-236

VT-

31

64 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 65: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

111-

H

PS

I Dis

char

ge W

est W

rap

supp

orts

SI-1

00V

T-3

41

3S

I-236

VT-

31

112-

H

PS

I Dis

char

ge E

ast W

rap

supp

orts

SI-1

00V

T-3

13

3

SI-1

01V

T-3

4S

I-102

VT-

32

SI-1

76V

T-3

3

113-

HP

SI D

isch

arge

supp

orts

SI-1

07V

T-3

21

1

SI-1

08V

T-3

1S

I-109

VT-

31

SI-1

57V

T-3

5S

I-176

VT-

31

114

HP

SI H

eade

rsu

ppor

tsS

I-218

VT-

31

12

Loop

1A

& 1

BS

I-236

VT-

31

115

HP

SI H

eade

rsu

ppor

tsS

I-157

VT-

31

Loop

2A

& 2

BS

I-176

VT-

31

118

- HP

SI L

ong

Term

supp

orts

SI-1

06V

T-3

224

3

119

- HP

SI L

ong

Term

supp

orts

SI-1

14V

T-3

182

1S

I-319

VT-

32

65 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 66: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.2

0C

LAS

S 2

PIP

ING

SU

PP

OR

TSC

-SU

PP

OR

TS T

HA

T A

LLO

WTH

ER

MA

L M

OV

EM

EN

T (S

PR

ING

)*F

-A; C

runn

ing

perc

ent

--

-16

26

13

AC

T 44

2489

111

210

103

16

43-

Mai

n S

team

SG

1 E

ast

supp

orts

SG

-36

VT-

31

44-

Mai

n S

team

SG

1 W

est

supp

orts

SG

-33

VT-

32

45-

Mai

n S

team

SG

2 E

ast

supp

orts

SG

-42

VT-

31

46-

Mai

n S

team

SG

2 W

est

supp

orts

SG

-45

VT-

32

47-

Mai

n S

team

SG

1 W

est

supp

orts

SG

-206

VT-

31

48-

Mai

n S

team

SG

1 E

ast

supp

orts

SG

-207

VT-

31

49-

Mai

n S

team

SG

2 E

ast

supp

orts

SG

-208

VT-

31

50-

Mai

n S

team

SG

2 W

est

supp

orts

SG

-209

VT-

31

51-

Atm

osph

eric

Dum

p N

o. 1

supp

orts

SG

-59

VT-

31

SG

-70

VT-

31

52-

Atm

osph

eric

Dum

p N

o. 2

supp

orts

SG

-84

VT-

31

12

AC

T 44

2489

1S

G-1

03V

T-3

1

54-

Fee

dwat

er S

G N

o. 1

supp

orts

SG

-002

VT-

39

11

SG

-013

VT-

31

55-

Fee

dwat

er S

G N

o. 2

supp

orts

SG

-005

VT-

39

11

SG

-014

VT-

31

56-

Fee

dwat

er S

G N

o. 1

supp

orts

SG

-202

VT-

31

66 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 67: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

57-

Fee

dwat

er S

G N

o. 2

supp

orts

SG

-205

VT-

31

58-

Aux

& D

ownc

omer

FW

SG

1su

ppor

tsS

G-8

VT-

310

23

AF-

4V

T-3

1

59-

Aux

& D

ownc

omer

FW

SG

2su

ppor

tsA

F-00

6V

T-3

14

2S

G-1

1V

T-3

10

60-

Dow

ncom

er F

eedw

ater

SG

1su

ppor

tsS

G-2

00V

T-3

2

61-

Dow

ncom

er F

eedw

ater

SG

2su

ppor

tsS

G-2

03V

T-3

2

62-

Aux

iliar

y Fe

edw

ater

SG

1su

ppor

tsA

F-00

4V

T-3

1A

F-01

8V

T-3

1

63-

Aux

iliar

y Fe

edw

ater

SG

2su

ppor

tsA

F-00

6V

T-3

2

64-

Blo

wdo

wn

SG

1su

ppor

tsS

G-3

9V

T-3

51

1

65-

Blo

wdo

wn

SG

2su

ppor

tsS

G-4

8V

T-3

31

2

71-

LP

SI P

ump

Roo

m A

Dis

char

gesu

ppor

tsS

I-78

VT-

31

74-

LP

SI P

ump

Roo

m B

Dis

char

gesu

ppor

tsS

I-129

VT-

33

13

77-

CS

Pum

p R

oom

A D

isch

arge

supp

orts

SI-7

9V

T-3

2

79-

CS

Pum

p R

oom

B S

uctio

nsu

ppor

tsS

I-034

VT-

31

80-

CS

Pum

p R

oom

B D

isch

arge

supp

orts

SI-1

19V

T-3

41

2S

I-147

VT-

31

82-

SD

CH

X R

oom

Asu

ppor

tsS

I-78

VT-

30

83-

SD

CH

X R

oom

Asu

ppor

tsS

I-70

VT-

31

11

SI-8

7V

T-3

3S

I-90

VT-

31

67 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 68: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

85-

SD

CH

X R

oom

Bsu

ppor

tsS

I-119

VT-

31

SI-1

23V

T-3

1

86-

SD

CH

X R

oom

Bsu

ppor

tsS

I-72

VT-

34

43

S

I-129

VT-

34

SI-1

34V

T-3

5

SI-1

35V

T-3

2

88-

Eas

t Wra

psu

ppor

tsS

I-72

VT-

37

13

SI-7

3V

T-3

2

89-

Eas

t Wra

psu

ppor

tsS

I-194

VT-

31

91-

Wes

t Wra

psu

ppor

tsS

I-70

VT-

32

SI-7

1V

T-3

1

92-

Wes

t Wra

psu

ppor

tsS

I-239

VT-

33

11

SI-2

41V

T-3

1

93-

Wes

t Wra

psu

ppor

tsS

I-89

VT-

31

94-

A T

rain

Pip

e C

hase

& 8

8'su

ppor

tsS

I-89

VT-

31

95-

B T

rain

Pip

e C

hase

& 8

8'su

ppor

tsS

I-72

VT-

33

13

SI-1

94V

T-3

1

96-

Con

tain

men

t LP

SI t

o 1A

supp

orts

SI-2

02V

T-3

11

2A

CT

4424

891

97-

Con

tain

men

t LP

SI t

o 1B

supp

orts

SI-2

20V

T-3

00

2

99-

Con

tain

men

t LP

SI t

o 2B

supp

orts

SI-1

74V

T-3

21

1A

CT

4424

891

100-

C

onta

inm

ent L

PS

I A S

uctio

nsu

ppor

tsS

I-241

VT-

31

101-

C

onta

inm

ent L

PS

I B S

uctio

nsu

ppor

tsS

I-194

VT-

31

68 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 69: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

102-

S

I Pum

p S

uctio

n A

supp

orts

SI-3

07V

T-3

1

104-

S

I Pum

p S

uctio

n B

supp

orts

SI-3

08V

T-3

1

106-

H

PS

I Roo

m D

isch

arge

Asu

ppor

tsS

I-99

VT-

32

S

I-100

VT-

31

107-

H

PS

I Roo

m D

isch

arge

Bsu

ppor

tsS

I-107

VT-

33

12

108-

H

PS

I 88’

Pip

echa

sesu

ppor

tsS

I-100

VT-

31

SI-1

18V

T-3

1

109-

H

PS

I 88’

Pip

echa

sesu

ppor

tsS

I-107

VT-

33

110-

H

PS

I Dis

char

ge W

est W

rap

supp

orts

SI-1

07V

T-3

31

3

SI-2

18V

T-3

1

111-

H

PS

I Dis

char

ge W

est W

rap

supp

orts

SI-2

36V

T-3

1

113-

HP

SI D

isch

arge

supp

orts

SI-1

57V

T-3

1

118

- HP

SI L

ong

Term

supp

orts

SI-1

06V

T-3

2

119

- HP

SI L

ong

Term

supp

orts

SI-1

14V

T-3

11

1S

I-319

VT-

32

120-

C

onta

inm

ent S

pray

Asu

ppor

tsS

I-88

VT-

31

121-

C

onta

inm

ent S

pray

Bsu

ppor

tsS

I-130

VT-

31

69 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 70: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.4

0S

UP

PO

RTS

OTH

ER

TH

AN

PIP

ING

SU

PP

OR

TS*F

-A; B

runn

ing

perc

ent

--

-22

21

20**

22 T

otal

, 12

RE

Q'D

52

70M

ultip

le It

ems

53

100

68-

Reg

ener

ativ

e H

eat E

xcha

nger

supp

orts

7931

4V

T-3

22

3

72-

LPS

I Pum

p A

supp

orts

3MS

IAP

01V

T-3

33

2

75-

LPS

I Pum

p B

supp

orts

3MS

IBP

01V

T-3

3

78-

CS

Pum

p A

supp

orts

3MS

IAP

03V

T-3

3

81-

CS

Pum

p B

supp

orts

3MS

IBP

03V

T-3

33

3

116-

HP

SI P

ump

Asu

ppor

ts3M

SIA

P02

VT-

34

21

117-

HP

SI P

ump

Bsu

ppor

ts3M

SIB

P02

VT-

34

22

F1.4

0S

UP

PO

RTS

OTH

ER

TH

AN

PIP

ING

SU

PP

OR

TS*F

-A; C

runn

ing

perc

ent

--

-4

11

50**

4 To

tal,

2 R

EQ

'D1

310

0M

ultip

le It

ems

41-

Ste

am G

ener

ator

1sn

ubbe

rs24

2V

T-3

21

1

42-

Ste

am G

ener

ator

2sn

ubbe

rs24

3V

T-3

21

3

70 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 71: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 6.0 ASME CLASS 3

EXAMINATION SUMMARY

71 of 212 3INT-ISI-3, Rev. 3

Page 72: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

INDEX

EXAM CATEGORY

D-A Welded Attachments for Vessels, Piping, Pumps and Valves

D-B All Pressure Retaining Components

F-A Class 3 Supports

72 of 212 3INT-ISI-3, Rev. 3

Page 73: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

D-A

; WEL

DED

A

TTA

CH

MEN

TS F

OR

VES

SELS

, PIP

ING

, PU

MPS

, AN

D V

ALV

ES

P

ress

ure

Ves

sels

*

D1.

10W

elde

d A

ttach

men

ts*D

1.10

; run

ning

per

cent

--

-22

31

30**

10 re

q'd

due

to

32

50m

ultip

le c

omp

43

100

DF

Sys

tem

atta

chm

ents

DFA

-T02

VT-

12

11

D

FB-T

02

DG

Sys

tem

atta

chm

ents

DG

A-E

04V

T-1

81

1D

GA

-E05

12

DG

B-E

041

3D

GB

-E05

DG

A-X

01A

DG

A-X

01B

DG

B-X

01A

DG

B-X

01B

EC

Sys

tem

atta

chm

ents

EC

A-E

-1V

T-1

41

2E

CA

-T-1

13

EC

B-E

-1E

CB

-T-1

E

W S

yste

mat

tach

men

tsE

WA

-E01

VT-

14

11

EW

A-T

011

3E

WB

-E01

EW

B-T

01

PC

Sys

tem

atta

chm

ents

PC

A-E

1V

T-1

21

2P

CB

-E1

SI S

yste

mat

tach

men

tsS

IA-E

01V

T-1

21

3S

IB-E

01

73 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 74: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

P

ipin

g

D1.

20W

elde

d A

ttach

men

ts*D

1.20

; run

ning

per

cent

--

-24

410

14

CR

AI 4

4208

1210

28

93

11

AF

Sys

tem

atta

chm

ents

pipi

ngV

T-1

91

CT

Sys

tem

atta

chm

ents

pipi

ngV

T-1

31

DG

Sys

tem

atta

chm

ents

pipi

ngV

T-1

142

CR

AI 4

4208

12

EC

Sys

tem

atta

chm

ents

pipi

ngV

T-1

142

EW

Sys

tem

atta

chm

ents

pipi

ngV

T-1

374

NC

Sys

tem

atta

chm

ents

pipi

ngV

T-1

192

PC

Sys

tem

atta

chm

ents

pipi

ngV

T-1

132

SG

Sys

tem

atta

chm

ents

pipi

ngV

T-1

41

SI S

yste

mat

tach

men

tspi

ping

VT-

12

1

SP

Sys

tem

atta

chm

ents

pipi

ngV

T-1

129

13

EXA

M C

ATE

GO

RY

D-B

; ALL

PR

ESSU

RE

RET

AIN

ING

CO

MPO

NEN

TS

D2.

10P

ress

ure

reta

inin

g co

mpo

nent

sC

lass

3IW

D-5

221

VT-

2*

**

**N

ote

ISI P

ress

ure

Pro

gram

74 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 75: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

F-A

; SU

PPO

RTS

F1

.30

CLA

SS 3

PIP

ING

SU

PPO

RTS

A-O

NE

DIR

ECTI

ON

AL

RO

D H

AN

GER

S*F

-A; A

runn

ing

perc

ent

AF

Sys

tem

supp

orts

pipi

ngV

T-3

11

IPC

A 1

1-01

5, A

CT

4162

637

B-M

ULT

IDIR

ECTI

ON

AL

RES

TRA

INTS

*F-A

; B ru

nnin

g pe

rcen

t-

--

319

181

5C

RA

I 442

0812

92

810

311

AF

Sys

tem

supp

orts

pipi

ngV

T-3

183

CT

Sys

tem

supp

orts

pipi

ngV

T-3

31

DG

Sys

tem

supp

orts

pipi

ngV

T-3

303

CR

AI 4

4208

12

EC

Sys

tem

supp

orts

pipi

ngV

T-3

162

EW

Sys

tem

supp

orts

pipi

ngV

T-3

677

NC

Sys

tem

supp

orts

pipi

ngV

T-3

354

PC

Sys

tem

supp

orts

pipi

ngV

T-3

172

SG

Sys

tem

supp

orts

pipi

ngV

T-3

41

SI S

yste

msu

ppor

tspi

ping

VT-

34

1

SP

Sys

tem

supp

orts

pipi

ngV

T-3

125

13

75 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 76: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.3

0C

LASS

3 P

IPIN

G S

UPP

OR

TSB

-MU

LTID

IREC

TIO

NA

L R

ESTR

AIN

TS*F

-A; C

runn

ing

perc

ent

--

-56

41

75

216

53

25

AF

Sys

tem

supp

orts

pipi

ngV

T-3

101

DG

Sys

tem

supp

orts

pipi

ngV

T-3

41

EC

Sys

tem

supp

orts

pipi

ngV

T-3

21

EW

Sys

tem

supp

orts

pipi

ngV

T-3

92

NC

Sys

tem

supp

orts

pipi

ngV

T-3

11

PC

Sys

tem

supp

orts

pipi

ngV

T-3

133

SG

Sys

tem

supp

orts

pipi

ngV

T-3

72

SI S

yste

msu

ppor

tspi

ping

VT-

31

1

SP

Sys

tem

supp

orts

pipi

ngV

T-3

92

76 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 77: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

F1.4

0SU

PPO

RTS

OTH

ER T

HA

NPI

PIN

G S

UPP

OR

TS*F

-A; B

runn

ing

perc

ent

--

-22

31

30**

10 re

q'd

due

to

32

50m

ultip

le c

omp

43

100

D

F S

yste

msu

ppor

tsD

FA-T

02V

T-3

21

1D

FB-T

02

DG

Sys

tem

supp

orts

DG

A-E

04V

T-3

81

1D

GB

-E04

12

DG

A-E

051

3D

GB

-E05

DG

A-X

01A

DG

A-X

01B

DG

B-X

01A

DG

B-X

01B

EC

Sys

tem

atta

chm

ents

EC

A-E

-1V

T-3

41

2E

CB

-E-1

13

EC

A-T

-1E

CB

-T-1

E

W S

yste

mat

tach

men

tsE

WA

-E01

VT-

34

11

EW

B-E

011

3E

WA

-T01

EW

B-T

01

PC

Sys

tem

atta

chm

ents

PC

A-E

1V

T-3

21

2P

CB

-E1

SI S

yste

mat

tach

men

tsS

IA-E

01V

T-3

21

3S

IB-E

01

77 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 78: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 7.0 AUGMENTED EXAMINATION SUMMARY

78 of 212 3INT-ISI-3, Rev. 3

Page 79: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

INDEX

EXAM CATEGORY

N-722-1 PWR Components Containing Alloy 600/82/182

N-729-1 PWR Reactor Vessel Upper Head

N-770-1 PWR Pressure Retaining Dissimilar Metal Piping and Vessel Nozzle Butt Welds containing Alloy 82/182

B-J Pressure Retaining Welds in Piping

B-G-1 Pressure Retaining Bolting, Greater Than 2 Inches in Diameter

B-G-2 Pressure Retaining Bolting, 2 Inches and Less in Diameter

B-P All Pressure Retaining Components

C-F-1 Pressure Retaining Welds in Austenitic Stainless Steel or High Alloy Piping

C-F-2 Pressure Retaining Welds in Carbon or Low Alloy Steel Piping

AUGMENTED HIGH ENERGY

C-F-2 Pressure Retaining Welds in Carbon or Low Alloy Steel Piping

AUGMENTED FLYWHEEL

NA Reactor Coolant Pump Flywheel Examinations

79 of 212 3INT-ISI-3, Rev. 3

Page 80: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

CC

722-

1; P

WR

C

OM

PON

ENTS

CO

NTA

ININ

G A

LLO

Y 60

0/82

/182

R

EA

CTO

R V

ES

SE

L

B15

.80

RP

V b

otto

m m

ount

ed in

stru

men

t pe

netra

tions

1-R

eact

or V

esse

lIC

I Pen

etra

tions

6537

3V

E61

61*

**

Req

uire

d R

15, R

17,

R19

(AC

T 41

6263

7).

STE

AM

GE

NE

RA

TOR

B15

.135

3-

Col

d le

g in

stru

men

t con

nect

ions

Pen

etra

tions

242

VE

44

***

***

***

Pro

rate

d ov

er

inve

rval

per

Foo

tnot

e 6

of C

ode

Cas

e (A

CT

4162

637)

.

4-

C

old

leg

inst

rum

ent c

onne

ctio

nsP

enet

ratio

ns24

3V

E4

4**

***

*

PR

ES

SU

RIZ

ER

B15

.140

Hea

ter P

enet

ratio

nsP

enet

ratio

ns65

373

VE

3636

****

**E

ach

RFO

B15

.180

Inst

rum

ent C

onne

ctio

nsIn

stru

men

ts65

373

VE

77

****

PIP

ING

B

15.2

00H

ot L

eg In

stru

men

t Con

nect

ions

Inst

rum

ents

RC

SV

E27

27**

**

B15

.205

Col

d le

g in

stru

men

t con

nect

ions

Pro

rate

ove

r inv

erva

l pe

r Foo

tnot

e 6

of

RC

S C

old

Leg

Inst

rum

ent

RC

SV

E12

12**

***

*C

ode

Cas

e R

CP

Pre

ssur

e Ta

psIn

stru

men

t R

CP

VE

88

***

***

80 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 81: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

B15

.215

Col

d le

g fu

ll pe

netra

tion

wel

ds

23-

Saf

ety

Inje

ctio

n 1A

butt

wel

dsS

I-207

-14”

VE

11

***

***

***V

E in

con

junc

tion

with

N-7

70-1

VO

L,P

rora

te o

ver i

nver

val

24-

Saf

ety

Inje

ctio

n 1B

butt

wel

dsS

I-223

-14”

VE

11

***

***

per F

ootn

ote

6 of

C

ode

Cas

e 25

- S

afet

y In

ject

ion

2Abu

tt w

elds

SI-1

60-1

4”V

E1

1**

***

*(A

CT

4162

637)

.

26-

Saf

ety

Inje

ctio

n 2B

butt

wel

dsS

I-179

-14”

VE

11

***

***

27-

Pzr

Spr

ay 1

Abu

tt w

elds

RC

-062

-3"

VE

11

***

***

28-

Pzr

Spr

ay 1

Bbu

tt w

elds

RC

-017

-3"

VE

11

***

***

32-

Dra

in L

ine

Loop

1A

butt

wel

dsR

C-0

60-2

”V

E1

1**

***

*

33-

Dra

in L

ine

Loop

1B

butt

wel

dsR

C-0

58-2

”V

E1

1**

***

*

34-

Dra

in L

ine

Loop

2A

butt

wel

dsR

C-0

96-2

”V

E1

1**

***

*

36-

Let

dow

n Li

nebu

tt w

elds

RC

-091

-2”

VE

11

***

***

37-

Cha

rgin

g Li

nebu

tt w

elds

CH

-005

-3”

VE

11

***

***

81 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 82: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

CO

DE

CA

SE N

-729

-1; P

WR

REA

CTO

R V

ESSE

L U

PPER

HEA

D

R

EA

CTO

R V

ES

SE

L U

PP

ER

HE

AD

B4.

30

Hea

d w

ith n

ozzl

es a

nd p

artia

l-pe

netra

tion

wel

ds o

f PW

SC

C-r

esis

tant

m

ater

ials

2-C

losu

re H

ead

wel

dN

0506

5-C

HA

-03

VE

9797

*10

0*R

15 (H

ead

repl

aced

)R

equi

red

R18

, R21

2-C

losu

re H

ead

Ven

t Noz

zle

N05

065-

CH

A-0

3V

E1

1*

100

*R15

(Hea

d re

plac

ed)

Req

uire

d R

18, R

21

B4.

40N

ozzl

es a

nd p

artia

l-pen

etra

tion

wel

ds o

f P

WS

CC

-res

ista

nt m

ater

ials

in h

ead

2-C

losu

re H

ead

CE

DM

Noz

zles

N05

065-

CH

A-0

3S

or V

ol97

97*

100

* no

t to

exce

ed 2

020

2-C

losu

re H

ead

Ven

t Noz

zle

N05

065-

CH

A-0

3S

or V

ol1

1*

100

* no

t to

exce

ed 2

020

82 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 83: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

CO

DE

CA

SE N

-770

-1; P

WR

PR

ESSU

RE

RET

AIN

ING

DIS

SIM

ILA

R M

ETA

L PI

PIN

G A

ND

VE

SSEL

NO

ZZLE

BU

TT W

ELD

S C

ON

TAIN

ING

A

LLO

Y 82

/182

Cra

cked

but

t wel

d re

info

rced

by

full

stru

ctur

al w

eld

over

lay

of A

lloy

52/1

52

mat

eria

l

IN

SPEC

TIO

N IT

EM F

Insp

ectio

n fre

quen

cy

mee

ts C

ode

Cas

e N

-77

0-1,

Rel

ief R

eque

st

36, a

nd S

DO

C N

001-

0604

-009

03 (S

uppl

ier

No.

PV

23Q

405)

. (C

RA

I 43

4878

1)

NO

MIN

AL

PIP

E S

IZE

> 4

INC

H

NO

ZZLE

TO

SA

FEE

ND

BU

TT W

ELD

S

Miti

gate

d w

ith F

SW

O

Dur

ing

R13

; 1st

ISI

R15

29-

Spr

aybu

tt w

elds

RC

-18-

4”V

ol6

12

1620

- S

urge

*bu

tt w

elds

RC

-028

-12”

Vol

1

332

*Des

ign

Cal

c E

xam

31

- S

afet

ies

(4)

butt

wel

dsR

C-0

01-6

”V

olFr

eque

ncy

3 ye

ars;

RC

-003

-6”

Vol

requ

ired

R17

, R19

, R

21

RC

-005

-6”

Vol

See

SD

OC

N00

1-06

04-

0090

3 (S

uppl

ier N

o.

PV

23Q

405)

. (C

RA

I 43

4878

1)R

C-0

07-6

”V

ol N

PS

4 O

R L

AR

GE

RM

itiga

ted

with

FS

WO

Dur

ing

R13

; 1st

ISI

R15

20-

**

Pre

ssur

izer

Sur

ge L

ine

butt

wel

dsR

C-0

28-1

2”V

ol3

13

33**

Des

ign

Cal

c E

xam

21

- S

hutd

own

Coo

ling

Loop

1bu

tt w

elds

RC

-051

-16"

Vol

Freq

uenc

y 6

year

s;

22-

Shu

tdow

n C

oolin

g Lo

op 2

butt

wel

dsR

C-0

68-1

6”V

olre

quire

d R

19

83 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 84: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

Unm

itiga

ted

butt

wel

d at

Col

d Le

g op

erat

ing

tem

pera

ture

IN

SPEC

TIO

N IT

EM B

23-

Saf

ety

Inje

ctio

n 1A

butt

wel

dsS

I-207

-14”

VE

& V

ol1

110

0E

xam

ined

R15

, R

EQ

UIR

ED

R19

24-

Saf

ety

Inje

ctio

n 1B

butt

wel

dsS

I-223

-14”

VE

& V

ol1

110

0E

xam

ined

R15

, R

EQ

UIR

ED

R19

25-

Saf

ety

Inje

ctio

n 2A

butt

wel

dsS

I-160

-14”

VE

& V

ol1

110

0E

xam

ined

R15

, R

EQ

UIR

ED

R19

26-

Saf

ety

Inje

ctio

n 2B

butt

wel

dsS

I-179

-14”

VE

& V

ol1

110

0E

xam

ined

R15

, R

EQ

UIR

ED

R19

27-

Pre

ssur

izer

Spr

ay 1

Abu

tt w

elds

RC

-062

-3”

VE

& V

ol1

110

0R

EQ

UIR

ED

R16

, R20

28-

Pre

ssur

izer

Spr

ay 1

Bbu

tt w

elds

RC

-017

-3”

VE

& V

ol1

110

0R

EQ

UIR

ED

R16

, R20

32-

Dra

in L

ine

Loop

1A

butt

wel

dsR

C-0

60-2

”V

E &

Vol

11

100

RE

QU

IRE

D R

16, R

20

33-

Dra

in L

ine

Loop

1B

butt

wel

dsR

C-0

58-2

”V

E &

Vol

11

100

RE

QU

IRE

D R

16, R

20

34-

Dra

in L

ine

Loop

2A

butt

wel

dsR

C-0

96-2

”V

E &

Vol

11

100

RE

QU

IRE

D R

16, R

20

36-

Let

dow

n Li

nebu

tt w

elds

CH

-001

-2”

VE

& V

ol1

110

0R

EQ

UIR

ED

R16

, R20

37-

Cha

rgin

g Li

nebu

tt w

elds

CH

-005

-2”

VE

& V

ol1

110

0R

EQ

UIR

ED

R16

, R20

84 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 85: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-P

; ALL

PR

ESSU

RE

RET

AIN

ING

CO

MPO

NEN

TS

*100

% e

ach

outa

ge

UN

INS

ULA

TED

(S

UP

PO

RTS

P

RE

SS

UR

E T

ES

T P

RO

GR

AM

)

RE

AC

TOR

VE

SS

EL

B15

.10

CLO

SU

RE

HE

AD

NU

TS

2-

Clo

sure

Hea

dnu

ts7.

237”

x 7

.91"

VT-

20

0**

0**

Del

eted

from

pr

ogra

m

per A

CT

4162

637.

B15

.10

CLO

SU

RE

STU

DS

See

als

o B

6.20

.

2-

Clo

sure

Hea

dst

uds

7.38

0” x

76.

37"

VT-

254

54*

*

PR

ES

SU

RIZ

ER

B15

.10

BO

LTS

, STU

DS

AN

D N

UTS

See

als

o B

7.20

.

5-

Pre

ssur

izer

Man

way

Stu

ds &

Nut

s1.

31” x

14.

5”V

T-2

2020

**

STE

AM

GE

NE

RA

TOR

B15

.10

BO

LTS

, STU

DS

AN

D N

UTS

See

als

o B

7.30

.

3-

Ste

am G

ener

ator

1 M

AN

WA

YS

Stu

ds &

Nut

s1.

31” x

14.

5”V

T-2

4040

**

4-

Ste

am G

ener

ator

2 M

AN

WA

YS

Stu

ds &

Nut

s1.

31” x

14.

5”V

T-2

4040

**

PIP

ING

B15

.10

BO

LTS

, STU

DS

AN

D N

UTS

See

als

o B

7.50

.31

- P

ress

uriz

er S

afet

ies

Flan

ge B

oltin

gR

C-0

01-6

”V

T-2

88

**

Flan

ge B

oltin

gR

C-0

03-6

”V

T-2

88

**

Flan

ge B

oltin

gR

C-0

05-6

”V

T-2

88

**

Flan

ge B

oltin

gR

C-0

07-6

”V

T-2

88

**

37-

Cha

rgin

g Li

neFl

ange

V43

5C

H-0

05-2

”V

T-2

88

**

85 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 86: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

B-J

; PR

ESSU

RE

RET

AIN

ING

WEL

DS

IN P

IPIN

G

B9.

20LE

SS

TH

AN

NP

S 4

B9.

21C

IRC

UM

FER

EN

TIA

L W

ELD

S O

THE

R

THA

N P

WR

HP

SI S

YS

TEM

S

30-

Aux

Pre

ssur

izer

Spr

ay**

butt

wel

dsC

H-0

09-2

”S

22

310

0**

IEB

88-

08 &

IN 9

7-19 2

wel

ds a

nd b

ase

met

al d

own

stre

amof

V43

1

EXA

M C

ATE

GO

RY

B-G

-1; P

RES

SUR

E R

ETA

ININ

G B

OLT

ING

GR

EATE

R T

HA

N 2

IN. I

N

DIA

MET

ER

Rem

oved

IEB

82-

02

exam

s pe

r CR

AI

4052

305.

EXA

M C

ATE

GO

RY

B-G

-2; P

RES

SUR

E R

ETA

ININ

G B

OLT

ING

2 IN

. AN

D L

ESS

IN

DIA

MET

ER

Rem

oved

IEB

82-

02

exam

s p

er C

RA

I 40

5230

5.

86 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 87: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

AU

GM

ENTE

D C

-F-1

AN

D C

-F-2

PIP

ING

WEL

DS

> 3/

8 IN

NO

MIN

AL

WA

LL T

HIC

KN

ESS

FOR

PI

PIN

G >

NPS

4S

ee a

lso

C5.

11 a

nd

C5.

51.

C

IRC

UM

FER

EN

TIA

L W

ELD

C5.

1158

- A

ux &

Dow

ncom

er F

W S

G 1

But

t Wel

dsS

G-8

-6”

S &

Vol

1**

12

100

**E

xam

inat

ion

RE

QD

by

S

G-8

-8”

IEB

79-

13 &

SE

R 8

3-07 (5

8-1;

59-

1)

C5.

1159

- A

ux &

Dow

ncom

er F

W S

G 2

But

t Wel

dsS

G-1

1-6”

S &

Vol

1**

13

100

SG

-11-

8”

C5.

5154

-FW

SG

114

” x 0

.938

”S

G-0

02S

& V

ol2*

21

100

**E

xam

inat

ion

RE

QD

by

SG

-013

IE

B 7

9-13

& S

ER

83-

07 (54-

1 &

15;

55-

1 &

15)

C5.

5155

-FW

SG

214

” x 0

.938

”S

G-0

05S

& V

ol2*

23

100

SG

-014

87 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 88: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

EXA

M C

ATE

GO

RY

C-F

-2; P

RES

SUR

E R

ETA

ININ

G W

ELD

S IN

CA

RB

ON

OR

LO

W

ALL

OY

STEE

L PI

PIN

G

(*) I

dent

ifies

the

num

ber o

f wel

ds th

at

are

not i

n th

e A

SM

E

CL

2 bo

unda

ry

AH

E5.

50

PIP

ING

WE

LDS

> 3

/8 IN

NO

MIN

AL

WA

LL T

HIC

KN

ES

S F

OR

PIP

ING

>N

PS

4

**10

0% o

f all

inte

rsec

ting

long

itudi

nal w

elds

will

be

exa

min

ed

AH

E5.

51C

IRC

UM

FER

EN

TIA

L W

ELD

**

Vol

umet

ric e

xam

s of

A

HE

requ

ired

per

UFS

AR

6.6

.1. (

CR

AI

4178

277)

Num

ber i

n pa

rent

hesi

s is

out

side

of

Cla

ss b

ound

ary.

*cat

egor

y ru

nnin

g pe

rcen

t20

150

124

AC

T 44

2489

10

224

15

13

100

47-

Mai

n S

team

SG

1 W

est

But

t Wel

dsS

G-2

06-2

8”S

& V

ol4(

1)12

1S

G-2

06-1

2”2

SG

-206

-6”

5

48-

Mai

n S

team

SG

1 E

ast

But

t Wel

dsS

G-2

07-2

8”S

& V

ol4(

1)12

2S

G-2

07-1

2”2

SG

-207

-6”

5

49-

Mai

n S

team

SG

2 E

ast

But

t Wel

dsS

G-2

08-2

8”S

& V

ol4(

1)12

3S

G-2

08-1

2”2

SG

-208

-6”

5

50-

Mai

n S

team

SG

2 W

est

But

t Wel

dsS

G-2

09-2

8”S

& V

ol4(

1)12

3S

G-2

09-1

2”2

SG

-209

-6”

5

51-

Atm

osph

eric

Dum

p N

o. 1

But

t Wel

dsS

G-5

9-12

”S

& V

ol13

131

SG

-70-

12”

1616

2

52-

Atm

osph

eric

Dum

p N

o. 2

But

t Wel

dsS

G-8

4-12

”S

& V

ol13

133

88 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 89: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

SG

-103

-12”

1616

53-

Ste

am to

Aux

Fee

dwat

erB

utt W

elds

SG

-81-

6”S

& V

ol14

141

SG

-83-

6”14

143

56-

Fee

dwat

er S

G N

o. 1

But

t Wel

dsS

G-2

01-2

4”S

& V

ol2

62

SG

-202

-24”

2S

G-2

24-2

4"2

57-

Fee

dwat

er S

G N

o. 2

But

t Wel

dsS

G-2

04-2

4”S

& V

ol2

63

SG

-205

-24”

2S

G-2

25-2

4"2

60-

Dow

ncom

er F

eedw

ater

SG

1B

utt W

elds

SG

-200

-8”

S &

Vol

2(8)

141

SG

-008

-8”

4

61-

Dow

ncom

er F

eedw

ater

SG

2B

utt W

elds

SG

-203

-8”

S &

Vol

2(8)

143

SG

-11-

8”4

66-

Blo

wdo

wn

SG

1B

utt W

elds

SG

-39-

6”S

& V

ol2(

13)

152

67-

Blo

wdo

wn

SG

2B

utt W

elds

SG

-48-

6”S

& V

ol2(

10)

123

89 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 90: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ASM

E IT

EM

NO

ZON

E-C

OM

PON

ENT

OR

SYS

TEM

IDEN

TIFI

CA

TIO

ND

ESC

RIP

TIO

N,

LIN

E O

R S

ERIA

L N

O

ND

E M

ETH

OD

TOTA

L IT

EMS

EXA

M

AM

OU

NT

IN

SPEC

TIO

N

PER

IOD

RU

NN

ING

%

REM

AR

KS

AH

E5.

60

PIP

ING

WE

LDS

>1/

5" N

OM

INA

L W

ALL

TH

ICK

NE

SS

FO

R P

IPIN

G >

NP

S 2

A

ND

< N

PS

4

AH

E5.

61C

IRC

UM

FER

EN

TIA

L**

Vol

umet

ric e

xam

s of

A

HE

requ

ired

per

UFS

AR

6.6

.1. (

CR

AI

4178

277)

*cat

egor

y ru

nnin

g pe

rcen

t40

121

30A

CT

4424

891

02

30

283

100

51-

Atm

osph

eric

Dum

p N

o. 1

But

t Wel

dsS

G-9

5-4”

S &

Vol

2010

110

2

52-

Atm

osph

eric

Dum

p N

o. 2

But

t Wel

dsS

G-1

00-4

”S

& V

ol20

203

AH

E5.

80P

IPE

BR

AN

CH

CO

NN

EC

TIO

NS

OF

BR

AN

CH

PIP

ING

> N

PS

2

AH

E5.

81C

IRC

UM

FER

EN

TIA

L

Cat

egor

y de

lete

d,

scop

e m

oved

to C

5.81

. (C

RA

I 417

8277

)

EXA

M C

ATE

GO

RY

NA

; RC

P FL

YWH

EEL

EXA

MIN

ATI

ON

S PE

R R

EG G

UID

E 1.

14

NA

16-R

eact

or C

oola

nt P

ump

1Afly

whe

el1A

S &

Vol

44

310

0S

OF

ALL

EX

PO

SE

D

17 R

eact

or C

oola

nt P

ump

1Bfly

whe

el1B

SU

RFA

CE

S a

nd U

T O

F

18-R

eact

or C

oola

nt P

ump

2Afly

whe

el2A

HIG

H S

TRE

SS

A

RE

AS

19-R

eact

or C

oola

nt P

ump

2Bfly

whe

el2B

Req

uire

d pe

r ITS

5.5

.7.

90 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 91: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 8.0 REQUESTS FOR RELIEF

91 of 212 3INT-ISI-3, Rev. 3

Page 92: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

RELIEF REQUESTS INDEX

NUMBER DESCRIPTION

31. Reactor Coolant System Hot Leg Alloy 600 Small-Bore Nozzles

34. Included for reference to document that the Interval 2 Reactor Vessel volumetric examinations were extended for 1 fuel cycle.

NRC accepted as documented by SER attached to Letter dated September 20, 2006.

35. Included for reference to document that the Interval 2 Reactor Vessel visual examinations were extended for 1 fuel cycle.

NRC accepted as documented by SER attached to Letter dated October 4, 2006.

36. Full Structural Weld Metal Overlay and for Units 1 and 3 only; Request to use 2001 Edition thru 2003 Addenda for Repair and Replacements

NRC accepted as documented by SER attached to Letter dated June 21, 2007

37. Alternative to ASME Code Case N-638-1, Similar and Dissimilar Metal Welding Using Ambient Temperature Machine GTAW Temperbead Technique.

NRC accepted as documented by SER attached to Letter dated June 21, 2007

38 Included for reference to document the Close out of U2 2nd Interval

39. Safety Injection Tank alternative repair method.

Submitted by APS letter 102-05869-DCM/RJR, dated July 11, 2008

40. Extended Reactor Vessel Examinations to meet the PWROG program

Submitted by APS letter

41. Request to utilize Appendix 1 of Code Case N-729-1.

Submitted by APS letter

42. Request to utilize Leak Path Assessments N-729-1 previously qualified

Submitted by APS letter

43. Included for reference to document the Closeout of U3 2nd Interval

Submitted by APS letter

44. Extended Reactor Vessel Examinations

Submitted by APS letter

45. Included for reference to document the Closeout of U2 RPV 2nd Interval

46. Included for reference to document the Closeout of U1 2nd Interval

47. Included for reference to document the Closeout of U3 RPV 2nd Interval

48. Request for Relief to use UT in Lieu or RT

49. Request to use Alternative Inspection method for Reactor Vessel Leak-off line

92 of 212 3INT-ISI-3, Rev. 3

Page 93: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 9.0 ISI

BOUNDARY DRAWINGS

93 of 212 3INT-ISI-3, Rev. 3

Page 94: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

BOUNDARY DRAWING INDEX

Drawing No. Drawing Title Code Class 03-M-AFP-001 Auxiliary - Feedwater System 2 & 3 03-M-CHP-001 Chemical and Volume Control System 1 & 2 03-M-CHP-002 Chemical and Volume Control System 2 & 3 03-M-CHP-003 Chemical and Volume Control System 2 03-M-CLP-001 Containment Integrated and Local Leak Rate Test 2 03-M-CPP-001 Containment Purge System 2 03-M-CTP-001 Condensate Purge System 2 03-M-DFP-001 Diesel Fuel Oil & Transfer System 3 03-M-DGP-001 Diesel Generator System 3 03-M-DWP-002 Demineralized Water System 2 03-M-ECP-001 Essential Chilled Water System 3 03-M-EWP-001 Essential Cooling Water System 3 03-M-FPP-006 Fire Protection System 2 03-M-GAP-001 Service Gas Supply System (N2 and H2) 2 & 3 03-N-GRP-001 Gaseous Radwaste System 2 03-M-HCP-001 HVAC Containment Building 2 03-M-HPP-001 Containment Hydrogen Control 2 03-M-IAP-002 Instrument and Service Air System 2 03-M-IAP-003 Instrument and Service Air System 2 03-M-NCP-002 Nuclear Cooling Water System 3 03-M-NCP-003 Nuclear Cooling Water System 2 03-M-PCP-001 Fuel Pool Cooling & Cleanup System 2 & 3 03-M-RCP-001 Reactor Coolant System 1 & 2 03-M-RCP-002 Reactor Coolant System 1 & 2 03-M-RDP-001 Radioactive Waste Drain System 2 03-M-SGP-001 Main Steam System 2 & 3 03-M-SGP-002 Main Steam System 2 03-M-SIP-001 Safety Injection and Shutdown Cooling System 2 03-M-SIP-002 Safety Injection and Shutdown Cooling System 1 & 2 03-M-SIP-003 Safety Injection and Shutdown Cooling System 2 03-M-SPP-001 Essential Spray Pond System 3 03-M-SPP-002 Essential Spray Pond System 3 03-N-SSP-001 Nuclear Sampling System 2 03-M-WCP-001 Normal Chilled Water System 2 13-M-ZZP-001 Symbols and Legend N/A 13-M-ZZP-002 Symbols and Legend N/A

94 of 212 3INT-ISI-3, Rev. 3

Page 95: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 10.0 ZONE DRAWINGS

95 of 212 3INT-ISI-3, Rev. 3

Page 96: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ZONE DRAWING INDEX

Drawing No. Drawing Title Code Class Zone 1 Reactor Vessel 1 Zone 2 Closure Head 1 Zone 3 Steam Generator 1 1 Zone 4 Steam Generator 2 1 Zone 5 Pressurizer 1 Zone 6 RCS Primary Piping 1 Zone 16 Reactor Coolant Pump 1A 1 Zone 17 Reactor Coolant Pump 1B 1 Zone 18 Reactor Coolant Pump 2A 1 Zone 19 Reactor Coolant Pump 2B 1 Zone 20 Pressurizer Surge Line 1 Zone 21 Shutdown Cooling Loop 1 1 Zone 22 Shutdown Cooling Loop 2 1 Zone 23 Safety Injection 1A 1 Zone 24 Safety Injection 1B 1 Zone 25 Safety Injection 2A 1 Zone 26 Safety Injection 2B 1 Zone 27 Pressurizer Spray 1A 1 Zone 28 Pressurizer Spray 1B 1 Zone 29 Combined Pressurizer Spray 1 Zone 30 Aux. Pressurizer Spray 1 Zone 31 Pressurizer Safeties 1 Zone 32 Drain Line 1A 1 Zone 33 Drain Line 1B 1 Zone 34 Drain Line 2A 1 Zone 35 Drain Line 2B 1 Zone 36 Letdown Line 1 Zone 37 Charging Line 1 Zone 38 Drain Line Loop 1 1 Zone 39 HPSI Long Term Recirc 1 1 Zone 40 HPSI Long Term Recirc 2 1 Zone 41 Steam Generator 1 2 Zone 42 Steam Generator 2 2 Zone 43 Main Steam SG1 East 2 Zone 44 Main Steam SG1 West 2 Zone 45 Main Steam SG2 East 2 Zone 46 Main Steam SG2 West 2 Zone 47 Main Steam SG1 West 2 Zone 48 Main Steam SG1 East 2 Zone 49 Main Steam SG2 East 2 Zone 50 Main Steam SG2 West 2 Zone 51 Atmospheric Dump No. 1 2 Zone 52 Atmospheric Dump No. 2 2 Zone 53 Steam to Aux Feedwater System 2 Zone 54 Feedwater SG No. 1 2 Zone 55 Feedwater SG No. 2 2 Zone 56 Feedwater SG No. 1 2 Zone 57 Feedwater SG No. 2 2 Zone 58 Aux & Downcomer Feedwater SG 1 2 Zone 59 Aux & Downcomer Feedwater SG 2 2 Zone 60 Downcomer Feedwater SG 1 2 Zone 61 Downcomer Feedwater SG 2 2 Zone 62 Aux Feedwater SG 1 2 Zone 63 Aux Feedwater SG 2 2

96 of 212 3INT-ISI-3, Rev. 3

Page 97: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

ZONE DRAWING INDEX (Continued)

Drawing No. Drawing Title Code Class Zone 64 Blowdown SG 1 2 Zone 65 Blowdown SG 2 2 Zone 66 Blowdown SG 1 2 Zone 67 Blowdown SG 2 2 Zone 68 Regenerative Heat Exchanger 2 Zone 69 Letdown Heat Exchanger 2 Zone 70 LPSI Pump Room A Suction 2 Zone 71 LPSI Pump Room A Discharge 2 Zone 72 LPSI Pump A 2 Zone 73 LPSI Pump Room B Suction 2 Zone 74 LPSI Pump Room B Discharge 2 Zone 75 LPSI Pump B 2 Zone 76 Containment Spray Pump Room A Suction 2 Zone 77 Containment Spray Pump Room A Discharge 2 Zone 78 Containment Spray Pump A 2 Zone 79 Containment Spray Pump Room B Suction 2 Zone 80 Containment Spray Pump Room B Discharge 2 Zone 81 Containment Spray Pump B 2 Zone 82 Shutdown Cooling Heat Exchange Room A 2 Zone 83 Shutdown Cooling Heat Exchange Room A 2 Zone 84 Shutdown Cooling Heat Exchanger A 2 Zone 85 Shutdown Cooling Heat Exchanger Room B 2 Zone 86 Shutdown Cooling Heat Exchanger Room B 2 Zone 87 Shutdown Cooling Heat Exchanger B 2 Zone 88 East Wrap 2 Zone 89 East Wrap 2 Zone 90 East Wrap 2 Zone 91 West Wrap 2 Zone 92 West Wrap 2 Zone 93 West Wrap 2 Zone 94 A Train Misc. Pipe Chases & 88' Pipe Tunnel 2 Zone 95 B Train Misc. Pipe Chases & 88' Pipe Tunnel 2 Zone 96 Containment LPSI Header to Loop 1A 2 Zone 97 Containment LPSI Header to Loop 1B 2 Zone 98 Containment LPSI Header to Loop 2A 2 Zone 99 Containment LPSI Header to Loop 2B 2 Zone 100 Containment LPSI Train A Suction 2 Zone 101 Containment LPSI Train B Suction 2 Zone 102 SI Pumps Train “A” Suction 2 Zone 103 Refueling Water Suction Train “A” 2 Zone 104 SI Pumps Train “B” Suction 2 Zone 105 Refueling Water Suction Train “B” 2 Zone 106 HPSI Pump Room “A” Discharge 2 Zone 107 HPSI Pump Room “B” Discharge 2 Zone 108 HPSI Discharge 88’ Pipe Chase 2 Zone 109 HPSI Discharge 88’ Pipe Chase 2 Zone 110 HPSI Discharge West Wrap 2 Zone 111 HPSI Discharge West Wrap 2 Zone 112 HPSI Discharge East Wrap 2 Zone 113 HPSI Discharge East Wrap 2 Zone 114 Containment HPSI Header Loop 1A & 1B 2 Zone 115 Containment HPSI Header Loop 2A & 2B 2 Zone 116 HPSI Pump “A” 2 Zone 117 HPSI Pump “B” 2 Zone 118 HPSI Long Term 2 Zone 119 HPSI Long Term 2 Zone 120 Containment Spray A 2 Zone 121 Containment Spray B 2

97 of 212 3INT-ISI-3, Rev. 3

Page 98: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

6 1/

2”

9 1/

16”

SUPP

ORT

CO

LUM

NS

INLE

TO

UTL

ET

100%

LIG

AM

ENTS

54 S

TUD

HO

LES

CO

UN

TED

CLO

CK

WIS

EFR

OM

11 1

/4”

182

1/4”

SHEA

RK

EYS

40 A

T 1A

Col

d Le

g41

AT

1B C

old

Leg

42 A

T 2A

Col

d Le

g43

AT

2B C

old

Leg

PLA

NT

NO

RTH

180°

270°

90

°

1-19

180°

270°

90

°

SHEL

L SE

GM

ENT

CR

OSS

SEC

TIO

N

-LO

NG

SEA

MS-

REF

EREN

CE

DW

G:

N00

1-3.

01-1

5 A

ND

17

N00

1-3.

01-4

1 A

ND

61

N00

1-3.

01-7

2NO

TES:

TAG

NO

. SE

RIA

L N

O.

N.B

NO

.

3MR

CEX

0165

173

(C-E

)22

655

ZON

E 1

REA

CTO

R V

ESSE

L

1-1

1-15

1-18

1-16

1-11

1-17

1-20

1-14

1-7

1-5

1-3

1-9

1-10

1-13

1-2

1-6

1-12 1-

8 1-4

ICI P

enet

ratio

ns 1

thru

61

1-3

1

1-3

0

HL

B

HL

A

CL

2B

CL

1BC

L 1B

CL

2A

B B BB

98 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 99: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

83 9175

67 8666 74

9082

978173

897280

96859592

797188

707894

8493

77 6987 68

76

7.38

”8.

6”

11.5

”76.3

7”

NO

TES:

1) C

EDM

’S: I

TEM

NO

. - C

EDM

NO

.2)

TA

G N

O.3

MR

CEX

01

SER

IAL

NO

.050

65-C

HA

-03

(DO

OSA

N)

N

.B. N

O. 1

706

3) IT

EM 7

1 C

ON

TAIN

S 4

SIN

GLE

STU

DS

IN A

GR

AYLO

C C

LAM

P

REF

EREN

CE

DW

GS:

13-M

N-7

40 (R

epla

ced

RV H

ead

Spec

)

NU

TS

WA

SHER

S

CLO

SUR

EH

EAD

STU

DS

270°

90

°

18

CLO

SUR

E H

EAD

TOP

VIE

W

STU

D L

OC

ATI

ON

S1

THR

U 5

4C

W F

RO

M 0

°

NO

TE 3

RV

LMS

LOC

ATE

DA

T 92

& 9

6U

T B

asel

ine

Com

plet

ed o

n 2-

61 a

t CED

M lo

catio

ns:

54, 5

9, 6

5, 6

9, 7

1, 7

3, 7

7, 7

9,81

, 82,

84,

85,

87,

88,

89,

1 TH

RU

18

19 T

HR

U 3

637

TH

RU

54

ZON

E 2

CLO

SUR

E H

EAD

2-61

2-60

2-58

2-71

2-70

2-59

1 TH

RU

18

19 T

HR

U 3

637

TH

RU

54

1 TH

RU

18

19 T

HR

U 3

637

TH

RU

54

4) N

EW H

EAD

REP

LAC

EMEN

T R

15W

O 3

3887

52

CED

M P

enet

ratio

ns2-

89

VEN

T LI

NE

2-88

99 o

f 212

3IN

T-IS

I-3, R

ev. 3

Page 100: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 3

STEA

M G

ENER

ATO

R #

1

315°

14.5

0

2.75

6.37

.87

.56

1.31

0

MA

NW

AY

STU

DS

LOO

KIN

G D

OW

N3−26

90

°

18

45

°

0° M

AN

WA

YST

UD

S &

NU

TSN

OTE

1-

112°

MA

NW

AY

STU

DS

& N

UTS

-NO

TE 1

-

3−24

NO

TES:

1) S

tud

Loca

tion

is #

1 TD

C G

oing

CW

to #

20.

Seria

l NO

. 242

2) T

ag N

O 3

MR

CEE

01A

NB

NO

. 191

*

REF

EREN

CE

DW

GS:

MN

725-

A70

0, A

701,

A70

2, A

703,

A70

4 M

N72

5-A

419,

A42

5, A

440,

A44

8 *

MN

725-

A60

5, A

622,

A62

5

CH

AN

NEL

HEA

D C

RO

SS S

ECTI

ON

3-14

0

25”

31”

27”

9.3”

TUB

ESH

EET

SKIR

T

31

5° 45°

3-10

7

3-10

6

3-10

1

3-10

2

3-10

4

3-10

0

6.7”

202.

1”

37”

17.3

”4.

63”

3-10

8B

Col

d L

eg

3-99

4 In

stru

men

t Noz

zles

100

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 101: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 4

STEA

M G

ENER

ATO

R #

2

315°

14.5

0

2.75

6.37

.87

.56

1.31

0

MA

NW

AY

STU

DS

LOO

KIN

G D

OW

N

90

°

18

45

°

0° M

AN

WA

YST

UD

S &

NU

TSN

OTE

1-

112°

MA

NW

AY

STU

DS

& N

UTS

-NO

TE 1

-

4−24

4−26

NO

TES:

1) S

tud

Loca

tion

is #

1 TD

C G

oing

CW

to #

20.

Seria

l NO

. 243

REF

EREN

CE

DW

GS:

MN

725-

A70

0, A

701,

A70

2, A

703,

A70

4 2)

Tag

NO

3M

RC

EE01

B

MN

725-

A41

9, A

425,

A44

0, A

448

NB

NO

. 192

**

MN

725-

A60

5, A

622,

A62

5

4-10

0

CH

AN

NEL

HEA

D C

RO

SS S

ECTI

ON

4-14

0

25”

31”

27”

9.3”

TUB

ESH

EET

SKIR

T

31

5° 45°

4-10

7

4-10

6

4-10

1

4-10

2

4-10

4

6.7”

202.

1”

37”

17.3

”4.

63”

4-10

8B

4-99

4 In

stru

men

t Noz

zles

Col

d L

eg

101

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 102: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 5

PRES

SUR

IZER

REF

EREN

CE

DW

GS:

N00

1-06

04-0

0006

N

001-

0604

-000

90N

001-

0604

-000

31

N00

1-06

04-0

0096

14.5

0

2.75

6.37

.87

.56

1.31

0

MA

NW

AY

STU

DS

90

°

270°

STU

DS

& N

UTS

NO

TE 1

90

°

270°

0°96

1/4

5”

ID

UPP

ER S

HEL

L

LOW

ER S

HEL

L

90

°

270°

MA

NW

AY

TOP

VIE

WZO

NE

31

SKIR

T

48.7

”ID

(TY

P)

4”

ZON

E 20

ZON

E 29

368.

5”

5−10

5−7

5−14

5−11

5−13 5−

12

5−6

5−4

5−3

5−1

5−40

5−9

5−2

5−55−8

5−21

B

5−37

1)ST

UD

LO

CAT

ION

IS #

1 TD

C G

OIN

G C

W T

O #

202)

TA

G N

O 3

MR

CEX

02

SER

IAL

NO

. 653

73 (C

-E)

N.B

. NO

. 222

54

5−3

6H

EATE

RS

(36)

INST

RU

MEN

T N

OZZ

LES

(7)

102

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 103: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 6

RC

S PR

IMA

RY

PIP

ING

REF

EREN

CE

DW

GS:

**13

-P-Z

CG

-010

3N

001-

0607

-000

83 &

112

N00

1-06

07-0

0090

TH

RU

94

N00

1-06

07-0

0096

TH

RU

100

MN

725-

A34

3, A

383,

A70

8M

N72

5-A

419,

A62

2, A

609

NO

TES:

1) P

IPE

LON

G S

EAM

S AT

3:0

0 A

ND

9:0

0 PO

SITI

ON

S (F

OR

CE

SUPP

LIED

PIP

ING

ON

LY)

2) E

LBO

W L

ON

G S

EAM

S AT

LO

NG

AN

D S

HO

RT R

AD

IUS

(FO

R C

E SU

PPLI

ED P

IPIN

G O

NLY

)3)

AN

SALD

O P

IPIN

G A

ND

ELB

OW

S A

RE

SEA

MLE

SS (X

X-1

3, X

X-1

6 an

d X

X-1

9 on

ly)

4) P

IPIN

G W

CL

STA

MPE

D W

ITH

CEN

TER

PU

NC

H M

AR

KS.

CE

WEL

DS

REF

EREN

CED

WIT

H F

OO

TAG

EM

AR

KS.

AN

SALD

O W

ELD

S R

EFER

ENC

ED W

ITH

CEN

TER

PU

NC

H M

AR

KS

EAC

H 2

50 m

m.

5) F

OR

REP

LAC

EMEN

T W

ELD

S, P

ORT

ION

S O

F TH

E O

RIG

INA

L W

ELD

MAY

REM

AIN

. TH

E O

RIG

INA

L W

ELD

CA

P IS

JO

INED

TO

TH

E R

EPLA

CEM

ENT

WEL

D.

{* &

***

}

***

11-9

11-8

11-4

17-1

11-1

11-7 1-

281-

2913-7

13-4

13-8

13-9

13-1

18-1RC

P 2A

ZON

E 18

RC

P 1B

ZON

E 17

REA

CTO

RV

ESSE

LZO

NE

1SG

2ZO

NE

4SG

1ZO

NE

3

RC

P 1A

ZON

E 16

RC

P 2B

ZON

E 19

9-9

9-8

9-4

16-1

9-1

9-71-

321-

31

15-4

15-8

15-1

19-1

1-30

7-7

7-8

7-4

7-1

RC

-63

1-27

6-7

6-9

6-4

6-1

6-8

18-2

12-1

12-4

12-1

7

12-7

17-2

10-1

10-4

10-1

7

10-7

16-2

8-1

8-4

8-17

8-7

19-2 14

-114

-4

14-1

7

14-7

1A1B2A 2B

RC

-32

RC

-79

RC

-31

RC

-34

RC

-93

RC

-30

RC

-33

RC

-84

RC

-73

15-7

10-1

3

10-1

6

10-1

9

10-1

0

***

3-10

3*

4-10

3*

12-1

012

-19

12-1

6**

*

12-1

3

8-10

8-13

8-16

8-19

***

14-1

014

-19

14-1

3

14-1

6**

*

C

old

Leg

Inst

rum

ent N

ozzl

es6-

99

R

CP

Pres

sure

Tap

s6-

100

Hot

Leg

Inst

rum

ent N

ozzl

es6-

101

ZON

E 33

ZON

E 32

ZON

E 36

ZON

E 26

ZON

E 27

ZON

E 23

ZON

E 21

ZON

E 20

ZON

E 24

ZON

E 28

ZON

E 25

ZON

E 37

ZON

E 34

ZON

E 22

** N

ote

Ref

eren

ce D

raw

ing

for L

ocat

ions

103

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 104: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 16

REA

CTO

R C

OO

LAN

TPU

MP

1A

NO

TES:

1) S

TUD

LO

CAT

ION

S C

W F

RO

M

REF

EREN

CE

DW

GS:

N00

1-6.

02-4

18

D

ISC

HA

RG

E C

2) T

AG

NO

. 3M

RC

EP01

A

L

S

ERIA

L N

O. 1

111-

1A (C

-E)

N

.B. N

O. 2

3461

N00

1-6.

02-4

20 T

HR

U 4

23N

001-

6.02

-107

& 1

08

8.27

1.1”

SEA

L H

OU

SIN

G

STU

DS

FLA

NG

E ST

UD

S

32.8

7”

6.93

6.89

7.28

4.52

8”

4.33

SNU

BB

ER (2

)16

-17

AN

D

16-1

8

SEA

L H

OU

SIN

G

ST

UD

S &

NU

TS- N

OTE

1

FLA

NG

E ST

UD

S &

NU

TS- N

OTE

1

16-1

2 TH

RU

16-

15C

W F

RO

M D

ISC

NO

ZZLE

CO

LUM

NSU

PPO

RTS

(4)

LOW

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

UPP

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

16-1

9 A

ND

16

-20

MO

TOR

SU

PPO

RTST

AN

D

16-2

1 A

ND

16

-2216

-30

FLA

NG

E SU

RFA

CE

16-3

4C

ASI

NG

INTE

RN

AL

SUR

FAC

E

16-3

1

16-3

216

-33

B

B

CB B

104

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 105: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 17

REA

CTO

R C

OO

LAN

TPU

MP

1B

NO

TES:

1) S

TUD

LO

CAT

ION

S C

W F

RO

M

REF

EREN

CE

DW

GS:

N00

1-6.

02-4

18

D

ISC

HA

RG

E C

2) T

AG

NO

. 3M

RC

EP01

B

L

S

ERIA

L N

O. 1

111-

1B (C

-E)

N

.B. N

O. 2

3462

N00

1-6.

-420

TH

RU

423

N00

1-6.

02-1

07 &

108

8.27

1.1”

SEA

L H

OU

SIN

G

STU

DS

FLA

NG

E ST

UD

S

32.8

7”

6.93

6.89

7.28

4.52

8”

4.33

SNU

BB

ER (2

)

CW

FR

OM

DIS

CN

OZZ

LE

CO

LUM

NSU

PPO

RTS

(4)

LOW

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

MO

TOR

SU

PPO

RTST

AN

D

17-1

2 TH

RU

17-

15

17-1

7 A

ND

17

-18

UPP

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

17-1

9 A

ND

17

-20

17-2

1 A

ND

17

-2217

-30

FLA

NG

E SU

RFA

CE

17-3

4C

ASI

NG

INTE

RN

AL

SUR

FAC

E

17-3

1

17-3

217

-33 S

EAL

HO

USI

NG

STU

DS

& N

UTS

- NO

TE 1

FLA

NG

E ST

UD

S &

NU

TS- N

OTE

1

B

B

CB B

105

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 106: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

NO

TES:

1) S

TUD

LO

CAT

ION

S C

W F

RO

M

REF

EREN

CE

DW

GS:

N00

1-6.

02-4

18

D

ISC

HA

RG

E C

2) T

AG

NO

. 3M

RC

EP01

C

L

S

ERIA

L N

O. 1

111-

2A (C

-E)

N

.B. N

O. 2

3463

N00

1-6.

02-4

20 T

HR

U 4

23N

001-

6.02

-107

& 1

08

8.27

1.1”

SEA

L H

OU

SIN

G

STU

DS

FLA

NG

E ST

UD

S

32.8

7”

6.93

6.89

7.28

4.52

8”

4.33

SNU

BB

ER (2

)

CW

FR

OM

DIS

CN

OZZ

LE

CO

LUM

NSU

PPO

RTS

(4)

LOW

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

MO

TOR

SU

PPO

RTST

AN

D

ZON

E 18

REA

CTO

R C

OO

LAN

TPU

MP

2A

18-1

2 TH

RU

18-

15

18-1

7 A

ND

18

-18

UPP

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

18-1

9 A

ND

18

-20

18-2

1 A

ND

18

-2218

-30

FLA

NG

E SU

RFA

CE

18-3

4C

ASI

NG

INTE

RN

AL

SUR

FAC

E

SEA

L H

OU

SIN

G

ST

UD

S &

NU

TS- N

OTE

1

FLA

NG

E ST

UD

S &

NU

TS- N

OTE

1

18-3

1

18-3

218

-33

B

B

CB B

106

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 107: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 19

REA

CTO

R C

OO

LAN

TPU

MP

2B

NO

TES:

1) S

TUD

LO

CAT

ION

S C

W F

RO

M

REF

EREN

CE

DW

GS:

N00

1-6.

02-4

18

D

ISC

HA

RG

E C

2) T

AG

NO

. 3M

RC

EP01

D

L

S

ERIA

L N

O. 1

111-

2B (C

-E)

N

.B. N

O. 2

3464

N00

1-6.

02-4

20 T

HR

U 4

23N

001-

6.02

-107

& 1

08

8.27

1.1”

SEA

L H

OU

SIN

G

STU

DS

FLA

NG

E ST

UD

S

32.8

7”

6.93

6.89

7.28

4.52

8”

4.33

SNU

BB

ER (2

)

CW

FR

OM

DIS

CN

OZZ

LE

CO

LUM

NSU

PPO

RTS

(4)

LOW

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

MO

TOR

SU

PPO

RTST

AN

D

19-1

2 TH

RU

19-

15

19-1

7 A

ND

19

-18

UPP

ER H

OR

IZO

NTA

LSU

PPO

RTS

(2)

19-1

9 A

ND

19

-20

19-2

1 A

ND

19

-2219

-30

FLA

NG

E SU

RFA

CE

19-3

4C

ASI

NG

INTE

RN

AL

SUR

FAC

E

SEA

L H

OU

SIN

G

ST

UD

S &

NU

TS- N

OTE

1

FLA

NG

E ST

UD

S &

NU

TS- N

OTE

1

19-3

1

19-3

219

-33

B

B

CB

B

107

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 108: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 20

PRES

SUR

IZER

SU

RG

E

RC

028

H-1

PRES

SUR

IZER

ZON

E 5

HO

T LE

GZO

NE

6

RC

-E-0

28-B

CA

A-1

2”

EL 1

08’-

1 3/

4”

EL 1

08’-

5”

EL 1

10’-

5”

PLA

NT

NO

RTH

RC

-E-0

28-B

CA

A-1

2”

REF

EREN

CE

DR

AWIN

GS

03-P

-RC

F-10

1

20-2

20-3

20-4

20-5

20-6

20-7

20-8

20-9

20-1

0

RC

028

H-2

RC

028

H-3

RC

028

H-4

PRES

SUR

IZER

VAU

LT

5-34

OL

CS

SS

20-1

OL

SS CS

20-1

1 O

L

6-10

OL

CB

C

CR

C-3

2

108

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 109: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

SHU

TDO

WN

CO

OLI

NG

LOO

P 1

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-105

ZON

E 21

PLA

NT

NO

RTH

SI-2

40

H-1

0

21-1

2

21-1

3B21

-14

21-1

5

21-1

821-1

9

21-1

121

-9

21-8

21-6

21-4

21-2

1

21-1

7

21-1

0

21-7

21-5

21-2

2

21-1

321-1

6

SI-2

40

H-1

3

SI-2

40

H-4

SI-2

40

H-9

SI-2

40

H-7

SI-2

40

H-5

SI-2

40

H-1

5

SI-2

40

H-3

SI-2

40

H-1

6

SI-2

40

H-1

1

UV

-653

CO

NT

ON

ZON

E 10

0

UV

-651

SI-A

-240

-BC

AA

-16”

SEC

ON

DA

RY

SHIE

LD W

ALL

EL 8

9’-9

CO

NT

ON

ZO

NE

38

LOO

P 1

HO

T LE

G Z

ON

E 6

21-1

A

CO

NT

ON

ZO

NE

3921

-20

OL

6-11

OL

CS/

SS

RC

-E-0

51-B

CA

A-1

6”

21-3

21-2

4

21-2

5

21-2

6

SI-2

40

H-2

SI-2

40

H-1

4

SI-2

40

H-1

7

21-1

RC

-051

H-2

RC

-051

H-3

BB

C

C

B

B

B

B

B

B

BB

BB

R14

WO

296

7884

6-11

-OL,

21-

20-O

L

NO

TES:

B

RC

-32

109

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 110: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 22

SHU

TDO

WN

CO

OLI

NG

LOO

P 2

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-105

22-7

A

UV

-652

RC

-E-0

68-B

CA

A-1

6”

RC

68H

-4R

C68

H-1

SI19

3H

-23

SI19

3H

-17

SI19

3H

-20

22-8

22-1

7

22-2

6

22-1

5

22-1

1

22-1

422

-9

22-7

22-4

22-6

22-5

22-3

22-2

22-2

3

22-2

2

22-1

8

22-2

1

CO

NT

ON

ZON

E 40

T-W

ALL

CO

NT

ON

ZON

E 10

1U

V-6

54

SEC

ON

DA

RY

SHIE

LD W

ALL

LOO

P 2

HO

TLE

G Z

ON

E 6

W

SI-B

-193

-BC

AA

-16”

SI19

3H

-8

7-9-

OL

22-1

-OL

CS/

SS

W

B

B

B

B

BR

C68

H-3

CC

R14

WO

296

7888

7-9-

OL,

22-

1-O

L

NO

TES:

RC

-63

110

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 111: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 23

SAFE

TY IN

JEC

TIO

N 1

A

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-103

9-10

23-2

6

CS/

SSV

-237

SI-E

-207

-BC

AA

-14”

SI-2

07

H-1

1

SI-2

07

H-7

SI-2

07

H-3

23-2

3 23-2

4

23-1

6 23-1

7

23-1

9

23-2

0

23-1

2

23-1

5

23-2

2

23-1

4

23-9

23-8

23-6

23-7

23-4

23-2

23-1

UV

-634

V-5

42CO

NT

ON

ZO

NE

96

LOO

P 1A

CO

LDLE

G Z

ON

E 6

SEC

ON

DA

RY

SHIE

LD W

ALL

SI T

AN

K 1

A

V-2

35

SI-E

-203

-BC

AA

-12”

B

C

B

RC

-34

111

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 112: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 24

SAFE

TY IN

JEC

TIO

N 1

B

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-103

11-1

0C

S/SS

SI-E

-221

-BC

AA

-12”

V-2

47

LOO

P 1B

CO

LDLE

G Z

ON

E 6

SEC

ON

DA

RY

SHIE

LD W

ALL

UV

-644

V-5

43

CO

NT

ON

ZON

E 97

SI T

AN

K1B

SI-E

-223

-BC

AA

-14”

24-1

8

24-1

6

24-1

7

24-1

4

24-1

24-1

1 24-9

24-2

24-2

1

24-2

2

24-4

24-2

3

24-2

5

24-6

24-8

24-7

24-1

9

SI-2

23

H-8

SI-2

23

H-3

SI-2

23

H-1

V-2

45

CB

C

RC

-31

112

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 113: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 25

SAFE

TY IN

JEC

TIO

N 2

A

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-136

SI-E

-156

-BC

AA

-12”

LOO

P 2A

CO

LDLE

G Z

ON

E 6

UV

-614

V-5

40

CO

NT

ON

ZON

E 98

SI T

AN

K2A

25-2

2

SI-1

60

H-1

SI-E

-160

-BC

AA

-14”

V-2

15

SEC

ON

DA

RY

SHIE

LD W

ALL

V-2

17

SI-1

56

H-9

25-2

3

25-8

25-2

6

25-2

025

-19

25-7

25-9

25-2

9

25-1

8

25-2

7

25-6

25-2

25-4

25-1

25-1

0

25-1

6

25-1

1

25-1

3 25-1

4

25-1

5

13-1

0C

S/SS

B

C

RC

-79

113

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 114: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 26

SAFE

TY IN

JEC

TIO

N 2

B

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-136

LOO

P 2B

CO

LDLE

G Z

ON

E 6

UV

-624

V-2

27

CO

NT

ON

ZON

E 99

SI-E

-179

-BC

AA

-14” SE

CO

ND

AR

YSH

IELD

WA

LL

15-9

CS/

SS

SI T

AN

K2B

SI-1

79

H-1

1

SI-1

79

H-8

SI-1

75

H-2

1

SI-1

75

H-2

3

V-2

25

V-5

41

26-2

2

26-1

5

26-8

26-2

5

26-1

4

26-1

9

26-6

26-1

7

26-1

2

26-4

26-2

3

26-1

1

26-9

26-2

26-1

6

26-7

26-1

FLO

OR

EL -

100’

SI-E

-175

-BC

AA

-12”

B

C

B

C

RC

-93

114

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 115: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 27

PRES

SUR

IZER

SPR

AY

1A

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-RC

F-10

2

27-2

4

27-2

27-3

27-4

27-5 27

-627

-8

27-1

0

27-1

2

27-1

3

27-1

4

27-1

5

27-1

6

27-1

8

27-2

0

27-2

1

27-2

2

27-2

3

27-2

5

27-2

6

27-1

27-2

7

27-2

8

27-2

9

27-3

0

27-3

2

27-3

127-3

4

27-3

3

27-3

6

27-3

7

27-3

9

27-3

8

27-4

0

27-4

1

27-4

227

-43

27-4

4

9-11

SS CS

EL 1

01’-

4”

EL 1

23’-

10”

EL 1

16’-

10”

EL 1

11’-

0”

EL 1

19’-

6”EL

127

’-9

3/8”

EL 1

31’ 1

1 3/

8”

RC

-16

H-7

RC

-62

H-3

8R

C-6

2H

-37

RC

-62

H-3

3

RC

-62

H-3

2

RC

-62

H-2

8

RC

-62

H-3

0

RC

-62

H-2

6

RC

-62

H-2

4

RC

-62

H-2

1

RC

-62

H-3

9

PRES

SUR

IZER

VA

ULT

PRES

SUR

IZER

VA

ULT

ZON

E 29

CO

MB

INED

PZR

SPR

AY

PV 100E

V-24

3

RC-E

-016

-BCA

A-3”

RC-E

-062-B

CAA-

3”

V-24

0

CO

LD L

EGLO

OP

1AZO

NE

6

27-3

5

W

B

BB

B

C

B

C

B

B

C

B

RC

-E-0

62-B

CA

A-3

RC

-34

115

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 116: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 28

PRES

SUR

IZER

SPR

AY

1B

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-RC

F-10

2 R

C-1

8H

-12

28-2

28-1

28-3

28-4

28-5

28-6 28

-7

28-9

28-1

1

28-1

3

28-1

4

28-1

5

28-1

7

28-1

828-2

0

28-2

2

28-2

3

28-2

4

28-2

5

28-2

628

-2728

-28

28-2

928

-30

28-3

1

28-3

2

28-3

3

28-3

4

28-3

5

28-3

6

28-3

7

28-4

6

28-3

9

28-4

0

28-4

1

28-4

2

11-1

1

28-4

528

-44

28-4

3SS C

S

RC

-18

H-9

RC

-17

H-4

6

RC

-17

H-4

3

RC

-17

H-4

2

RC

-17

H-4

0

RC

-17

H-3

8

RC

-17

H-3

4

RC

-17

H-3

3

RC

-17

H-3

1

RC

-17

H-3

0

RC

-17

H-2

6

RC

-17

H-2

4

ZON

E 29

CO

MB

INED

PZR

SPR

AY

PRES

SUR

IZER

VA

ULT

PRES

SUR

IZER

VA

ULT

1A &

1B

CU

BIC

LE

CO

LD L

EGLO

OP

1B Z

ON

E 6

EL 1

02’-

1/4”

EL 1

14’-

6”

EL 1

10’-

0”

EL 1

23’-

10”

EL 1

16’-

10”

EL 1

27’ 9

3/8

RC

-E-0

18-B

CA

A-3

V-2

42

V-2

41

PV 100F

RC-E

-017-B

CAA-

3”

W

B

C

C

B

B

B

BB

B

B

B

B

C

RC

-31

116

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 117: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 29

CO

MB

INED

PZR

SPR

AY

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-RC

F-10

2

RC

-18

H-1

7

RC

-18

H-1

6

RC

-18

H-1

8

29-1

3

PRES

SUR

IZER

ZON

E 5

ZON

E 27

PZR

SPR

AY1A

ZON

E 28

PZR

SPR

AY1B

C E

L 13

0”-1

1 3/

8”L

158’

-1 5

/16”

WP

EL 1

58’-

2”

ZON

E 30

AU

X S

PRAY

NO

ZZLE

EL 1

52’-

5 5/

8”

SS CS

RC

-E-0

18-B

CA

A-4

29-1

1

29-1

2

29-9

29-1

1A

29-5

29-7

29-1

0

29-4

29-3

29-2

5-33

OL

29-1

OL

C

C

C

117

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 118: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 30

AU

X. P

ZR S

PRA

Y

REF

EREN

CE

DR

AWIN

GS

03-P

-CH

F-10

7

HV

-205

CH

-B-5

21-B

CA

A-2

CH

-521

H-A

V-4

31

HV

-203

30-1

0

30-9

30-1

30-2

30-4

30-5

30-6

30-7

R

30-1

2RC

H-5

21

H-B

EL 1

53’-

8”

ZON

E 29

C

OM

BIN

EDPZ

R S

PRA

Y

CH

-A-5

20-B

CA

A-2

CH

-E-0

09-B

CA

A-2

30-8

30-2

1

30-2

230

-23

CB

R14

WO

332

9247

, 332

9254

30-2

0, 3

0-21

, 30-

22, 3

0-23

NO

TES:

30-7

R, 3

0-12

R

SW

SWSW

30-1

130

-20

SW

118

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 119: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 31

PRES

SUR

IZER

SA

FETI

ES

REF

EREN

CE

DR

AWIN

GS

03-P

-RC

F-11

4

PRES

SUR

IZER

ZON

E 5

TOP

HEA

D

RC

-E-0

01-B

CA

A-6

RC

-E-0

05-B

CA

A-6

RC

-E-0

03-B

CA

A-6

RC

-E-0

07-B

CA

A-6

31-1

1

31-7

31-1

5

31-9

31-1

0

31-6

31-5

31-1

3

31-1

4

31-3

31-2

31-1

PSV

200

PSV

203

PSV

202

PSV

201

NO

TE:

8 -

2” S

TUD

S

CS

SS

CS

SS

CS

SS

CS

SS

16 -

NU

TS

FLA

NG

E B

OLT

ING

FLA

NG

E B

OLT

ING

FLA

NG

E B

OLT

ING

FLA

NG

E B

OLT

ING

5-29

OL

5-32

OL

5-31

OL

5-30

OL

119

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 120: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 32

DR

AIN

LIN

E 1A

REF

EREN

CE

DR

AWIN

GS

03-P

-CH

F-11

0

RC

-60

H-A V

-334

RC

-E-0

60-B

CA

A-2

CO

LD L

EGZO

NE

6 LO

OP

1A

V-2

34

WP

EL 8

8’-1

0 3/

16”

EL 8

9’ 9

11/

16”

32-1

32-3

8-18

32-5

32-8

32-2

32-6

32-4

32-9

CS

SS

NO

TE:

S

W =

SO

CK

ET W

ELD

SW

SW

SW

N

B

RC

-33

120

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 121: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 33

DR

AIN

LIN

E 1B

REF

EREN

CE

DR

AWIN

GS

03-P

-CH

F-11

0

RC

-58

H-A

V-3

35

RC

-E-0

58-B

CA

A-2

CO

LD L

EGZO

NE

6 LO

OP

1B

V-2

35

33-1

10-1

833-8

33-9

CS

SS

NO

TE:

S

W =

SO

CK

ET W

ELD

SW

SW

N33

-6

SW

33-5

33-4

33-3

33-2

EL 8

9’

B

RC

-30 12

1 of

212

3IN

T-IS

I-3, R

ev. 3

Page 122: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 34

DR

AIN

LIN

E 2A

REF

EREN

CE

DR

AWIN

GS

03-P

-CH

F-11

0

V-2

33

RC

-E-0

96-B

CA

A-2

V-3

33

12-1

8

34-834

-9C

SSS

NO

TE:

S

W =

SO

CK

ET W

ELD

SW SW

N

34-6

SW

34-1

34-2

34-3

34-4

34-5

CO

LD L

EGLO

OP

2AZO

NE

6R

C-7

3

122

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 123: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 35

DR

AIN

LIN

E 2B

REF

EREN

CE

DR

AWIN

GS

03-P

-CH

F-11

0

V-2

32

RC

-E-0

89-B

CA

A-2

” V-3

32

35-8

35-9

NO

TE:

S

W =

SO

CK

ET W

ELD

SW

SW

N

35-6

SW

35-1

35-3

35-2

35-4

35-5

EL 8

8’ 9

5/8

”LE

TDO

WN

LIN

EZO

NE

36

123

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 124: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 36

LETD

OW

N L

INE

REF

EREN

CE

DR

AWIN

GS

03-P

-CH

F-01

42

CH

-E-0

01-B

CA

A-2

UV

-515

ZON

E 6

ZON

E 35

EL 102’

EL 94’

EL 119’

EL 131’

EL 121’

53

56

54

55

59

63

57

61

60

67

58

62

6869

6465

70

82

77

40

75

1

17

83

62

38

81

318

5

74

19

1312

20

27

11

25

15

21

109

28

8

26

22

29

14

3031

84

33

48

23

32

16

34

35

42

49

46

50

4347

45

52 80

44

5124

79

41

76

39

78

RC

91H

T

RC

91H

AK

RC

91H

AC

RC

91H

JRC

91H

AD

RC

91H

P

RC

91H

AP

RC

91H

AQ

RC

91H

5

RC

91H

6

RC

91H

AJ

RC

91H

Q

RC

91H

U

RC

91H

W

CH

IH

A

W

W

UV

-516

RC

-E-0

91-B

CA

A-2

87

14-1

8C

SSS

W

W

B

B

B

B

B

B

B

BB

B

B

B

BB

B

RC

-E-0

91-B

CA

A-1

6”

RC

-E-0

91-B

CA

A-2

RC

-E-0

91-B

CA

A-2

RC

-E-0

91-B

CA

A-2

RC

-84

124

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 125: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 37

CH

AR

GIN

G L

INE

CH

-E-0

05-B

CA

A-3

” V43

3

ZON

E 6

EL 101’

EL 112’

EL 134’

EL 131’

EL 110’EL 11

5’

36

43 42

19

41

18B

18A

40

17

15

14

39

13

12

11

10

38

7

6

5

37

4

3

2 1

4745

44

27

25

24

2321

20

26

22

333231302928

34

5758

59

6061

62

5453

52

55

5156

49 48

50

CH

-5H

36

CH

-5H

28

CH

-5H

27

CH

-5H

19CH

-5H

17

CH

-5H

42

CH

-5H

18

CH

-5H

20

CH

-5H

13

CH

-5H

14

CH

-5H

38

CH

-5H

33C

H-5

H39

CH

-5H

9

CH

-5H

8C

H-5

H7

CH

-5H

4

CH

-5H

3 CH

-5H

44

CH

-5H

34C

H-5

H35

CH

-5H

21

CH

-5H

22

CH

-5H

32

CH

-5H

37

13-1

1

V43

4

V43

5

PD

V24

0

REF

EREN

CE

DW

G.03

-P-C

HF-

109

FLA

NG

EB

OLT

ING

85

W

W

SS CS

C

C

C

B

C

CB

B

B

B

B

B

B

CB B

BB

BB

B

BC

C

C

See

Det

ail

A

Det

ail A

9R8R

V43

3

64

65

66

63

SW

SW

SW

SWR

15 W

O 3

4693

2530

-63,

30-

64, 3

0-65

,

NO

TES:

30-6

6, 3

0-8R

, 30-

9RCH

-E-0

05-B

CA

A-3

CH

-E-0

05-B

CA

A-2

7

10

CH

-E-0

05-B

CA

A-2

CH-E

-005

-BCA

A-2”

CH

-E-0

05-B

CA

A-3

CH

-E-0

05-B

CA

A-2

CH

-E-0

05-B

CA

A-2

CH

-E-0

05-B

CA

A-2

RC

-79

125

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 126: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 38

DR

AIN

LIN

E LO

OP

1

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-105

NO

TE:

S

W =

SO

CK

ET W

ELD

38-1

ZON

E 21

SHU

TDO

WN

CO

OLI

NG

RC

-E-0

70-B

CA

A-2

38-2

SWR

C-5

1

126

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 127: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 39

HPS

I LO

NG

TER

M R

ECIR

CLO

OP

1

SI-A

-248

-BC

AA

-3”

REF

EREN

CE

DW

G.03

-P-S

IF-1

05

C E

L 86

’ 8 1

/4”

LC

EL

88’ 2

”L C

EL

86’ 8

1/4

”L

C E

L 86

’ 8 1

/4”

L

C E

L 83

’ 5”

L

39-3

7

SI24

8H

29

SI24

8H

18

SI24

8H

25

SI24

8H

36

SI24

8H

20SI-A

-248

-BC

AA

-3”

SI-A

-248

-BC

AA

-3”

V-5

22

V-9

57

V-5

23

N

39-1

7

39-2

4

39-1

2

39-2

5

39-1

5

39-9

39-1

4

39-1

6

39-1

3

39-1

7A

39-2

0

39-3

8

39-2

1

39-1

9

39-2

2

39-1

8

39-2

3

39-2

639-2

7

39-2

8

39-3

4

39-2

9

39-1

0

39-1

139

-5

39-7

39-6

39-1

39-2

39-3

SHU

TDO

WN

CO

OLI

NG

ZON

E 21

SI-A

-248

-BC

AA

-3”

POIN

T A

39-6

0

39-6

1

39-6

239-6

3

39-8

1

39-6

5

39-6

639-6

739

-68

39-6

939-7

039

-71

39-7

2

SI24

8H

34

SI24

8H

35

39-7

3

CO

NT

POIN

T A

39-3

1

39-2

8

39-2

9

39-5

9

39-5

6

39-3

0

SI24

8H

32

39-5

839

-57

39-8

0

39-5

5C

C

B

B

C

B

B

B

B

SI24

8H

28

B

SI24

8H

19

CO

NT

ON

ZON

E 11

8

SI-A

-248

-BC

AA

-3”

127

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 128: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 40

HPS

I LO

NG

TER

MR

ECIR

CU

LATI

ON

2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-105

V 533

40-1

8

40-2

5

40-2

040

-7

40-8

40-2

1

40-2

340

-22

40-1

9

40-2

7

40-1

040

-13

40-1

2

40-6

EL. 9

3’

40-1

6

ZON

E22

40-1

5

40-1

4

40-1

40-5

40-9

40-2

40-3

40-4

SI-B

-199

-BC

AA

-3”

V 958

V 532

SI19

9H

15

SI19

9H

18

SI19

9H

17

SI19

9H

22

40-1

7

SI-B

-114

-CC

BA

-3”

EL. 8

4’

EL. 8

9’-3

C91

/2”

W

CO

NT

ON

ZON

E 11

9

B

CB

B

128

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 129: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 41

STEA

M G

ENER

ATO

R 1

107

41 42 270

°

90°

270

° 9

0°SE

CO

ND

ARY

M

AN

WAY

S-N

OTE

2-

SEC

ON

DA

RY

AT 0

°,90

°

-NO

TE 3

-

31”

TUB

E SH

EET

193”

ID4.

88”

5.83

”23

2” ID

3.41

”4.

3

ZON

E 58

ZON

E 54

ZON

E 64

AT 2

70°

AT 9

AT 4

5°AT

315

°

SEC

ON

DA

RY H

AN

DH

OLE

S AT

0°A

ND

270

°-N

OTE

3-

ZON

E 44

ZON

E 43

109

114

115

106

105

104

103

101

10010

2

FEED

WA

TER

DO

WN

COM

ER @

BLO

WD

OW

N

AT 1

180°

,270

°

HA

ND

HO

LES

DO

WN

CO

MER

REC

IRC

@ 4

5° 4

ΙΝ

ZON

E 64

DO

WN

CO

MER

BLO

WD

OW

N 6

@ 2

70°

@ 9

@ 1

80°

6.54

113

112

90°

270

°

HY

D S

NU

BB

ERS

NO

TES:

1) 0

° IS

AT

CEN

TER

OF

CO

LD L

EG M

AN

WA

Y

REF

EREN

CE

DW

GS:

2) S

TUD

S A

RE

16 -

1.5”

X 9

”3)

STU

DS

AR

E 16

- 1”

X 6

”4)

TA

G N

O. 3

MR

CEE

01A

SER

IAL

NO

. 242

N.B

. NO

. 191

MN

725-

A42

0, A

423,

A42

6, A

437,

A44

3, A

446

MN

725-

A70

0, A

701,

A73

1M

N72

5-A

395,

A62

2 an

d A

625

SNU

BB

ER L

UG

S

110

CC

+IR

+IR

+IR

+IR

129

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 130: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 42

STEA

M G

ENER

ATO

R 2

107

41 42 270

°

90°

270

° 9

0°SE

CO

ND

ARY

M

AN

WAY

S-N

OTE

2-

SEC

ON

DA

RY

AT 0

°,90

°

-NO

TE 3

-

31”

TUB

E SH

EET

193”

ID4.

88”

5.83

”23

2” ID

3.41

”4.

3

ZON

E 58

ZON

E 54

ZON

E 64

AT 2

70°

AT 9

AT 4

5°AT

315

°

SEC

ON

DA

RY H

AN

DH

OLE

S AT

0°A

ND

270

°-N

OTE

3-

ZON

E 44

ZON

E 43

109

114

115

106

105

104

103

101

10010

2

FEED

WA

TER

DO

WN

COM

ER @

BLO

WD

OW

N

AT 1

180°

,270

°

HA

ND

HO

LES

DO

WN

CO

MER

REC

IRC

@ 4

5° 4

ΙΝ

ZON

E 64

DO

WN

CO

MER

BLO

WD

OW

N 6

@ 2

70°

@ 9

@ 1

80°

6.54

113

112

90°

270

°SN

UB

BER

LU

GS

NO

TES:

1) 0

° IS

AT

CEN

TER

OF

CO

LD L

EG M

AN

WA

Y

REF

EREN

CE

DW

GS:

2) S

TUD

S A

RE

16 -

1.5”

X 9

”3)

STU

DS

AR

E 16

-1”

X 6

”4)

TA

G N

O. 3

MR

CEE

01B

SER

IAL

NO

. 243

N.B

. NO

. 193

MN

725-

A42

0, A

423,

A42

6, A

437,

A44

3, A

446

MN

725-

A70

0, A

701,

A73

1M

N72

5-A

395,

A62

2 an

d A

625

HY

D S

NU

BB

ERS

110

CC

+IR

+IR

+IR

+IR

130

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 131: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 43

MA

IN S

TEA

M (E

AST

)ST

EAM

GEN

ERA

TOR

1

2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-

P-SG

F-11

8

43-5

LIN

E #

DIA

/SC

HFR

OM

TO

SG-3

632

” x

2.00

”43

-1

-

SG36

H17

SG-E

-036

-DLB

B-2

8”

43-2

643

-2SG

-36

28”

x 1.

25”

SG36

H11

43-4

43-7

43-1

8

43-2

5

43-2

1

43-2

443

-17

43-1

5

43-1

2

43-2

2

WSG

36H

16

ZON

E48

EL. 1

32’

C

43-8

43-1

4

43-1

0

43-1

1

EL. 1

32’-

3C

1/16

EL. 1

57’-

10C

1/8”

EL. 1

71’

C

ZON

E41

43-2

43-1

43-2

0

W

EL. 1

58’

C

43-1

1A

43-2

6B

B

C

131

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 132: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 31

ZON

E 44

MA

IN S

TEA

M (W

EST)

STEA

M G

ENER

ATO

R 1

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-11

8

ZON

E41

44-5

LIN

E #

DIA

/SC

HFR

OM

TO

SG-3

332

” x

2.00

”44

-1

-

SG33

H17

SG-E

-033

-DLB

B-2

8”

44-3

144

-2SG

-33

28”

x 1.

25”

SG33

H11

44-4

44-7

44-2 44

-1

44-2

1

44-3

0

44-2

4

44-2

844

-20

44-1

7

44-1

2

44-2

3

44-2

6

WSG

33H

16

ZON

E47

EL. 1

32’

C

44-1

544

-8

44-1

4

44-1

0

44-1

144

-18

EL. 1

32’-

3C

3/8”

EL. 1

57’-

9C

3/4”

EL. 1

71’

C

44-1

1A

W

44-3

1B

CC

132

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 133: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 45

MA

IN S

TEA

M (E

AST

)

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-

P-SG

F-11

8

ZON

E42

45-5

LIN

E #

DIA

/SC

HFR

OM

TO

SG-4

232

”x 2

”45

-1

- SG-E

-042

-DLB

B-2

8”

45-2

645

-2SG

-42

28”x

1.2

5”

WSG

42H

17

SG42

H11

45-7

45-8 45

-10

45-4

45-2

45-1

45-1

8

45-1

4

45-1

2

45-1

1

45-2

5

45-1

5

45-2

4

45-1

7

45-2

0

45-2

2

45-2

1

WSG

42H

16

EL. 1

57’-

10C

ZON

E49

EL. 1

32’

C

1/8”

EL. 1

71’

C

EL. 1

32’-

3C

1/16

EL. 1

71’-

1C

11/1

6”

STEA

M G

ENER

ATO

R 2

3

45-1

1A

45-2

6

BB

C 133

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 134: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 46

MA

IN S

TEA

M (W

EST)

STEA

M G

ENER

ATO

R 2

4

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-

P-SG

F-11

8

EL. 1

71’

ZON

E42

46-5

C

LIN

E #

DIA

/SC

HFR

OM

TO

SG-4

532

”x 2

”46

-1

-

SG45

H17

SG-E

-045

-DLB

B-2

8”46-2

946

-2SG

-45

28”x

1.2

5”

SG45

H11

46-7

46-8 46

-10

46-4

46-2 46

-1

46-1

1

46-2

146

-12

46-1

8

46-2

5

46-1

4

46-2

4

46-1

5

46-2

0

46-1

7

46-2

7

46-2

3

46-2

8

WSG

45H

16

EL. 1

58’

C

EL. 1

32’

C

ZON

E50

EL. 1

32’

C

46-1

1A

W

46-2

9

B

C

C

134

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 135: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 47

MA

IN S

TEA

M (W

EST)

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

5

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

066”

x 1.

500”

47-4

47-2

0

SG20

6H

-1

47-3

0

47-2

9

47-1

47-2

8

28”x

1.7

50”

12”x

0.8

44”

SG-2

06

SG-2

06

EL. 1

32’-

0”

TUR

BIN

E

47-2

5

PSV

572

03-P

-SG

F-40

1

NO

TE:

1 - M

AIN

STE

AM

REL

IEF

VALV

E

47-1

9

47-1

2

47-2

4

47-1

1

47-2

0

47-3

0

47-1

5

47-2

7

47-2

8

47-2

3

47-2

9

47-1

6

UV

170

PSV

573

PSV

692

PSV

575

PSV

574 47

-747

-4

47-3

47-2

47-1

47-8

ZON

E 44

1

BU

ILD

ING

SG-E

-206

-DLB

B-1

2”

SG-E

-206

-DLB

B-2

8”

ZON

E 51

12-1

1/4

”DIA

. FLA

NG

E B

OLT

SPE

R V

ALV

E2

- MSI

V, 2

0-2

1/4”

DIA

. BO

DY

TO

BO

NN

ET B

OLT

S

EL. 1

29’-

0”

STEA

M G

ENER

ATO

R 1

C

135

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 136: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 48

MA

IN S

TEA

M (E

AST

)

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

5

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

076”

x 1.

500”

48-4

48-2

0

SG20

7H

-1

48-3

0

48-2

9

48-1

48-2

8

28”x

1.7

50”

12”x

0.8

44”

SG-2

07

SG-2

07

EL. 1

32’-

0”

TUR

BIN

E

48-2

5PS

V57

9

03-P

-SG

F-40

1

48-1

9

48-1

2

48-2

4

48-1

1

48-2

0

48-3

0

48-1

5

48-2

7

48-2

8

48-2

3

48-2

9

48-1

6

UV

180

PSV

578

PSV

691

PSV

576

PSV

577

48-7

48-4

48-3

48-2

48-1

48-8

ZON

E 43

2

BU

ILD

ING

SG-E

-207

-DLB

B-1

2”

SG-E

-207

-DLB

B-2

8”

ZON

E 51

ZON

E 53

48-3

5

48-3

4

MA

IN S

TEA

M S

/G #

190

° (E

AST

) IN

SID

EC

ON

TAIN

MEN

T

ZON

E 51

STEA

M G

ENER

ATO

R 1

NO

TE:

1 - M

AIN

STE

AM

REL

IEF

VALV

E12

-1 1

/4”D

IA. F

LAN

GE

BO

LTS

PER

VA

LVE

2 - M

SIV,

20-

2 1/

4”D

IA. B

OD

Y T

OB

ON

NET

BO

LTS

C

136

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 137: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 49

MA

IN S

TEA

M (E

AST

)

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03

-P-S

GF-

155

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

086”

x 1.

500”

49-4

49-2

0

SG20

8H

-1

49-3

0

49-2

9

49-1

49-2

8

28”x

1.7

50”

12”x

0.8

44”

SG-2

08

SG-2

08

EL. 1

32’-

0”

TUR

BIN

E

49-2

5PS

V55

4

03

-P-S

GF-

401

49-1

9

49-1

2

49-2

4

49-1

1

49-2

0

49-3

0

49-1

5

49-2

7

49-2

8

49-2

3

49-2

9

49-1

6

UV

171

PSV

555

PSV

695

PSV

557

PSV

556

49-7

49-4

49-3

49-2

49-1

49-8

ZON

E 45

3

BU

ILD

ING

SG-E

-208

-DLB

B-1

2”

SG-E

-208

-DLB

B-2

8”

ZON

E 52

ZON

E 53

49-3

5

ZON

E 52

49-3

4

STEA

M G

ENER

ATO

R 2

NO

TE:

1 - M

AIN

STE

AM

REL

IEF

VALV

E12

-1 1

/4”D

IA. F

LAN

GE

BO

LTS

PER

VA

LVE

2 - M

SIV,

20-

2 1/

4”D

IA. B

OD

Y T

OB

ON

NET

BO

LTS

C

137

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 138: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 50

MA

IN S

TEA

M (W

EST)

PLA

NT

NO

RTH

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

096”

x 1.

500”

50-4

50-2

0

SG20

9H

-1

50-3

0

50-2

9

50-1

50-2

8

28”x

1.7

50”

12”x

0.8

44”

SG-2

09

SG-2

09

EL. 1

32’-

0”

TUR

BIN

E

50-2

5

PSV

561

50-1

9

50-1

2

50-2

4

50-1

1

50-2

0

50-3

0

50-1

5

50-2

7

50-2

8

50-2

3

50-2

9

50-1

6

UV

181

PSV

560

PSV

694

PSV

558

PSV

559 50

-750

-4

50-3

50-2

50-1

50-8

ZON

E 46

4

BU

ILD

ING

SG-E

-209

-DLB

B-1

2”

SG-E

-209

-DLB

B-2

8”

ZON

E 52

S/G

#2

AD

V

STEA

M G

ENER

ATO

R 2

NO

TE:

1 - M

AIN

STE

AM

REL

IEF

VALV

E12

-1 1

/4”D

IA. F

LAN

GE

BO

LTS

PER

VA

LVE

2 - M

SIV,

20-

2 1/

4”D

IA. B

OD

Y T

OB

ON

NET

BO

LTS

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

503

-P-S

GF-

401

C

138

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 139: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 51

ATM

OSP

HER

IC D

UM

P 1

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

8

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

5912

”x 0

.844

”51

-151

-51

51-6

5

51-3

51-2

8

51-3

351

-151

-31

51-2

6

51-6

51-5

1

51-5

3

51-2

7

51-5

4

SG70

H-6

SG-0

7012

”x 0

.844

”51

-49

51-3

7

51-3

051

-32

ZON

E47

SG-E

-70-

DLB

B-1

2”

SG-E

-59-

DLB

B-1

2”

SG59

H-6

V 955

ZON

E48

51-2

51-7

51-2

9

51-5

51-8

B

51-3

5

51-4

51-9

51-8

A

51-3

7

51-3

4

51-4

9

HV

178

V 48

V 949

HV

184

UV

169

SG-E

-95-

DLB

B-4

SG-0

954”

x 0

.337

”51

-65

51-7

6

ZON

E48

51-3

6

51-5

6

51-5

5

51-5

751

-80

51-7

9

51-7

8

51-7

1

51-7

051

-68

51-8

451

-67

51-7

7

51-6

651

-82

51-8

3

51-6

9 51-8

151

-76

51-7

5

51-7

3

51-7

4

51-7

2

C

C

139

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 140: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 52

ATM

OSP

HER

IC D

UM

P 2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

8

LIN

E #

DIA

/SC

HFR

OM

TO

SG-1

0312

”x 0

.844

”52

-152

-50

52-5

3

52-3

4

52-3

7

52-3

52-1

0

52-3

1

52-5

2

52-5

5

52-9

52-8

52-5

6

52-1

SG10

3H

-6

SG-0

8412

”x 0

.844

”52

-52

52-3

8

52-6

52-7

52-4

52-5

ZON

E49

SG-E

-100

-DLB

B-4

SG-E

-084

-DLB

B-1

2”

ZON

E49

SG84

H-6

V 958

ZON

E50

52-3

5

52-3

0

52-3

8

52-5

7

52-3

2

52-2

8

52-3

3

52-2

7

52-2

9

52-5

4

52-5

0

HV

179

V 84

V 952

HV

185

UV

183

SG-E

-103

-DLB

B-1

2”

SG-1

004”

x 0

.337

”52

-65

52-7

6

52-2

52-8

3

52-6

8

52-8

4

52-8

052

-79

52-8

2

52-7

352

-72

52-7

4

52-7

6

52-7

0

52-7

152

-69

52-7

5

52-3

652

-77

52-7

852

-81

52-6

6

52-6

5

52-6

7

C

C

140

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 141: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 53

STEA

M T

O A

UX

ILIA

RY

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-AFF

-131

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

816”

x 0.

432”

53-1

53-1

5

53-3

5

53-2

6

53-2

7

53-2

3

53-2

1

53-1

1

53-2

53-1

2

53-3

4

53-2

853

-29

53-3

1

53-3

2

53-2

2

53-3

0

53-2

4

53-2

5

53-1

3

53-1

553

-14

53-9

53-8

53-1

0

53-1

EL. 1

22’-

5”

EL. 1

22’-

5”

SG-0

836”

x 0.

432”

53-3

553

-21

MA

IN S

TEA

M

53-6

53-7

53-4

53-5

ZON

E48

SG-E

-083

-DLB

B-6

SG-E

-81-

DLB

B-6

MA

IN S

TEA

MZO

NE

49

UV

134

UV

138

FEED

WA

TER

SY

STEM

141

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 142: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 54

FEED

WA

TER

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03

-P-S

GF-

119

ZON

E56

8

V 007

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

0214

”x 0

.938

”54

-15

54-2

4

54-4

5

54-5

354

-55

54-5

1

54-1

2R

54-7

R

54-8

R

54-3

1

54-3

8

54-6

0

54-5

0

54-5

9

54-5

7

54-5

6

54-5

254

-54

54-2

5B

54-3

4

54-2

5A

54-4

7

54-3

2

54-3

5

54-2

4

54-3

3

54-1

1AR

54-1

654

-15

54-1

0754

-6R

54-2

1

54-1

7

54-1

454

-13

54-2

754-2

6

54-4

9

54-4

3

EL. 9

3’

SG-2

H15

SG-1

3H

1

SG-2

H-9

SG-2

H12

SG-2

H-3

SG-2

H14

SG-2

H13

SG-2

H-5

SG-2

H-4

WSG

-2H

-1

EL. 1

15’

SG-0

02SG

-002

16”x

0.8

44”

16”x

1.7

5”54

-26

-54

-25A

54-1

07

V 003

54-3

6

54-3

7

54-2

0

54-1

9

54-3

9

54-4

154

-18

ZON

E41

54-2

254

-23

54-6

0

54-1

0R54

-12R

-

54-1

3,

54-1

54-1

1AR

54-1

00

24”x

1.2

18”

14”x

0.9

38”

16”x

0.8

44”

16”x

1.7

50”

SG-0

02

SG-0

13SG

-013

SG-0

13

54-1

54-2

9

54-1

00

54-5

54-1

0R54

-9R

54-2

8

54-2

54-3

54-4

SG-E

-002

-DLB

B-1

4”

SG-E-

002-DL

BB-24

SG-E

-013

-DLB

B-1

4”

54-3

0SG

-2H

10SG

-2H

11

SG-2

H-6

SG-2

H-8

STEA

M G

ENER

ATO

R 1

54-2

7

EL. 9

3’

W W

W

W W

C

B

C

B

C

B

C

B

C

B

C

C

C

C SG-E

-002

-DLB

B-1

6”S

G-E

-00

2-D

LB

B-2

4”

SG-2

H-2

SG-E-0

13-DL

BB-16

C

R16

WO

312

9871

54-6

R, 5

4-7R

, 54-

8R, 5

4-9R

,

NO

TES:

54-1

0R, 5

4-11

AR

, 54-

12R

142

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 143: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 55

FEED

WA

TER

STEA

M G

ENER

ATO

R 2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-11

9

ZON

E57

10 V 005

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

0514

”x 0

.938

”55

-15

55-2

4

55-4

7

55-5

355

-54

55-5

2

55-5

0

55-4

3

55-1

2R55

-7R

55-9

R

55-8

R

55-3

7

55-2

0

55-2

8

55-3

2

55-6

0

55-5

1

55-5

9

55-5

7

55-5

6 55-4

9

55-5

5

55-3

8

55-3

955

-41

55-4

5

55-3

3

55-3

655

-35

55-3

4

55-2

9

55-1

0R55-1

1R

55-3

1

55-3

0

55-3

55-4

55-5

55-6

R

55-1

55-2

55-1

355-1

455

-2755

-26

55-2

2

55-2

3

EL. 1

05’

EL. 9

4’

SG-5

H-6

SG-5

H14

SG-5

H11

SG-5

H10

SG-5

H-8

SG14

H-1

SG-5

H12

WSG

-5H

-9

SG-5

H-3

SG-5

H-2

SG-5

H13

SG-5

H-7

SG-5

H-5

SG-5

H-4

WSG

-5H

-1

EL. 1

15’

ZON

E42

SG-0

05SG

-005

16”x

0.8

44”

16”x

1.7

5”55

-26

-55

-25

55-1

07

V 006

55-1

555

-17 55

-18

55-1

6

55-1

07

55-2

1

55-1

9

55-1

00ZO

NE

42

55-2

555-2

4

55-6

0

55-1

0 R

55-1

2 R

-

55-1

3,

55-1

55-1

1 R55

-100

24”x

1.2

18”

14”x

0.9

38”

16”x

0.8

44”

16”x

1.7

5”

SG-0

05

SG-0

14SG

-014

SG-0

14 SG-E

-005

-DLB

B-14

SG-E

-005

-DLB

B-2

4”

SG-E

-014

-DLB

B-1

4”

55-2

7

W

WW

W

B

C

B

C

CC

C

C

C

B

C

BC

BC

R15

WO

338

1628

55-6

R, 5

5-7R

, 55-

8R, 5

5-9R

,

NO

TES:

55-1

0R, 5

5-11

R, 5

5-12

R

SG-E

-005

-DLB

B-1

6”

SG-E

-014

-DLB

B-1

6”

SG-E

-005-D

LBB-

24”

143

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 144: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 56

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-11

9

UV

132

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

0124

”x 1

.812

”6

7

SG20

2H

-1

SG-E

-202

-DLB

B-2

4”

4 11

1 9

24”x

1.5

31”

24”x

1.8

12”

SG-2

02

SG-2

24

EL. 1

15’-

6”

EL. 1

15’-

6”

56-1

1

SG-E

-201

-DLB

B-2

4”

SG-2

24-D

LBB

-24”

UV

174

03-P

-FW

F-40

3

NO

TE:

FWIV

, 20-

2B

OD

Y T

O B

ON

NET

BO

LTS

PER

VA

LVE

1/2”

DIA

ZON

E54

8

FEED

WA

TER

STEA

M G

ENER

ATO

R 1

56-9

56-7

56-4

56-1

56-6

WC

144

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 145: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 57

FEED

WA

TER

STEA

M G

ENER

ATO

R 2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-11

9

UV

137

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

0424

”x 1

.812

”57

-657

-7

SG20

5H

-2

SG-E

-205

-DLB

B-2

4”

57-4

57-1

1

57-1

57-9

24”x

1.5

31”

24”x

1.8

12”

SG-2

05

SG-2

25

EL. 1

15’-

6”

EL. 1

15’-

6”

57-1

1

SG-E

-204

-DLB

B-2

4”

SG-2

25-D

LBB

-24”

UV

177

03-P

-FW

F-40

3

NO

TE:

FWIV

, 20-

2B

OD

Y T

O B

ON

NET

BO

LTS

PER

VA

LVE

1/2”

DIA

10

57-6

57-9

57-7

57-4

57-1

ZON

E55

W

C

145

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 146: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 58

AU

XIL

IAR

Y &

DO

WN

CO

MER

FEED

WA

TER

SG

#1

11

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

0

3-P-

SGF-

120

ZON

E62

V 652

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

088”

x.50

0”58

-458

-25

58-2

0

58-1

6B

58-2

8

58-7

58-9

58-8

58-1

6A

58-1

6

58-2

2

58-2

158

-17

58-1

8

58-2

3

58-1

9

58-2

0A

58-2

958-2

6

58-1

4

58-1

5

58-1

0

58-1

1

58-1

2

58-3

58-4

58-5

58-6

58-1

58-2

41-1

11

58-1

3

EL. 1

31’-

0”

SG-8

H18

SG-8

H-9

SG-8

H-7

SG-8

H11

AF-

4H

-1

SG-8

H19

SG-8

H-4

SG-8

H14

SG-8

H-3

SG-8

H10

SG-8

H-2

SG-8

H-6

75

58-3

3

58-2

5 58-3

258

-34

V 079

58-2

4

SG-E

-008

-DC

BA

-6”

AF-

A-0

04-D

CB

A-6

ZON

E60

ZON

E41

58-3

58-3

4-

58-1

58-1

941

-111

6”x.

432”

6”x.

562”

6”x1

.8”

SG-0

08

AF-

004

SG-0

08

EL. 1

31’-

0”EL

. 120

’-0”

CS

EL. 8

9’ 9

1/2

EL. 1

43’-

4

58-3

0

58-3

1

58-2

7EL

. 100

’-0”

EL. 1

04’-

0”

EL. 1

31’-

0”

SS

5/16

SG-8

H-8

SG-8

H15

SG-8

H-5

SG-8

H20

58-3

5

SS CS

SG-E

-008

-DLB

B-8

SS CS

WB

C

CCB

CB

C

CB

C

B

C

C

C C

58-3

8

146

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 147: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 59

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03

-P-S

GF-

120

ZON

E63

V 653

LIN

E #

DIA

/SC

HFR

OM

TO

SG-1

18”

x.50

0”59

-459

-25

59-2

0

59-1

6B

59-3

1

59-2

8

59-7

59-9

59-8

59-1

6A

59-1

6

59-2

259

-21

59-3

0

59-1

7

59-1

8

59-2

3

59-1

6C59

-19

59-2

0A59

-29

59-2

6

59-1

4

59-1

5

59-1

0

59-1

159

-12

59-3

59-4

59-5

59-6

59-1

59-2

42-1

11

59-1

3

EL. 1

31’-

0”

SG11

H-3

SG11

H16

SG11

H14

SG11

H-2

AF-

6H

-1SG

11H

20

SG11

H-1

7

SG11

H-5

SG11

H-7

SG11

H-4

SG11

H18

SG11

H-8

SG11

H13

SG11

H11SG

11H

10

SG11

H-6

SG11

H-9

12

76

59-3

3

59-2

5

59-3

2

59-3

4V 08

0

59-2

4

SG-E

-011

-DC

BA

-6”

AF-

B-0

06-D

CB

A-6

SG-E

-011

-DC

BA

-8”

ZON

E61

ZON

E42

59-3

59-3

4-

59-1

59-1

6C42

-111

6”x.

432”

6”x.

562”

6”x1

.8”

SG-1

1

AF-

6SG

-11

EL. 1

43’-

4

EL. 1

31’-

0”

EL. 1

04’-

0”

EL. 8

9’-9

5/8”

1/2”

EL. 1

00’-

0”

EL. 1

20’-

0”

CS

SS

AU

XIL

IAR

Y &

DO

WN

CO

MER

FEED

WA

TER

SG

#2

59-3

759-3

8 ss/c

s

SG-E

-011

-DLB

B-8

CS

SS

W

W

BC

B

C

CC

B

C

B

C

B

C

B

C

C

C

C

59-3

9

147

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 148: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 60

DO

WN

CO

MER

FEE

DW

ATE

R

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

6

SG-E

-200

-DLB

B-8

EL. 1

14’-

10

ZON

E58

60-1

1

11

C

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

008”

x.71

9”60

-260

-12

EL. 1

04’-

0”C

SG20

0H

-13

SG20

0H

-14

UV

172

SG-0

088”

x.71

9”60

-14

60-1

7

UV

130

5/16

V64

2

SG-E

-008

-DLB

B-8

TUR

BIN

EB

UIL

DIN

G

STEA

M G

ENER

ATO

R #

1

60-1

4

60-8

60-1

2

60-9

60-6

60-1

6

60-1

5

60-7

60-4

60-5

60-3

60-2

60-1

7

CC

148

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 149: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 61

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

6

SG-E

-203

-DLB

B-8

EL. 1

14’-

10

ZON

E59

12

C

LIN

E #

DIA

/SC

HFR

OM

TO

SG-2

038”

x.71

9”61

-261

-12

EL. 1

04’-

0”C

SG20

3H

-14

SG20

3H

-13

UV

175

SG-0

118”

x.71

9”61

-14

61-1

7

UV

135

5/16

V69

3

SG-E

-011

-DLB

B-8

TUR

BIN

EB

UIL

DIN

G

DO

WN

CO

MER

FEE

DW

ATE

RST

EAM

GEN

ERA

TOR

#2

61-3

61-4 61

-6

61-2

61-5 61

-7

61-1

6

61-1

7

61-8

61-9

61-1

1

61-1

561

-14

61-1

2

CC

149

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 150: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 62

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-AFF

-132

AF-

B-0

18-D

CB

A-6

EL. 9

4’-5

ZON

E58

75

C

LIN

E #

DIA

/SC

HFR

OM

TO

AF-

018

6”x.

562”

62-4

62-1

4

AF-

A-0

04-D

CB

A-6

EL. 9

4’-5

”C

62-2

2

AF-

18H

1

AF-

4H

3

AF-

18H

2

WU

V 36

UV 34

AF-

004

6”x.

562”

62-1

862

-24

03-P

-AFF

-133

AU

XIL

IAR

Y F

EED

WA

TER

STEA

M G

ENER

ATO

R #

1

62-7

62-8

62-5

62-1

8

62-2

3

62-1

2

62-1

4

62-2

0

62-2

4

62-1

9

62-2

1

62-6

62-1

3

62-1

1

62-9

62-1

0

62-4

B

C

C

150

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 151: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 63

AU

XIL

IAR

Y F

EED

WA

TER

STEA

M G

ENER

ATO

R #

2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-AFF

-132

AF-

A-0

16-D

CB

A-6

EL. 8

2’ -4

ZON

E59

UV 37

C

LIN

E #

DIA

/SC

HFR

OM

TO

AF-

016

6”x

0.56

2”63

-18

63-1

9

AF1

6H

1

AF6 H2

AF6 H4

AF6 H3

AF6 H5

AF-

B-0

06-D

CB

A-6

”U

V 35

76

63-3

063

-4A

F-00

66”

x 0.

562”

03-P

-AFF

-133

63-2

5

63-2

1

63-2

8

63-2

363

-22

63-2

9

63-2

6 63-2

4

63-3

0

63-2

7

63-1

8A

63-4

63-1

4

63-1

963

-20

63-1

8 WB

C

B

C

B

AF-

B-0

06-D

CB

A-6

151

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 152: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 64

BLO

WD

OW

NST

EAM

GEN

ERA

TOR

#1

46

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03

-P-S

GF-

122

ZON

E66

V 289

64-4

464

-36

64-1

464

-49

64-3

864

-39

64-2

264

-7

64-8

64-3

164

-15

64-2

3

64-3

2

64-5

3

64-5

2

64-5

064-5

1

64-4

164

-40 64

-42

64-4

6

64-4

3

64-4

5

64-3

5

64-3

3

64-1

9

64-1

1

64-3

7

64-9

64-1

8

64-1

2

64-1

6

64-3

64-4

64-5

64-6

64-1

64-2

64-2

0

64-2

464

-25

64-2

164

-10

EL. 9

7’EL. 1

09’

HV 43

HV 41

SG39

H22

SG39

H-5

SG39

H24

SG53

H-5

SG39

H16

WSG

39H

15SG

39H

18

SG39

H12

SG39

H-9

SG39

H25

EL. 8

9’-3

UV

500P

ZON

E41

SG39

H10

64-2

7

64-2

864

-29

64-3

0

EL. 1

04’

SG-E

-053

-DA

BA

-6”

SG-E

-039

-DA

BA

-6”

SG-E

-039

-DA

BA

-6”

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

536”

x 0.

562”

64-1

64-1

4SG

-039

6”x

0.56

2”64

-15

64-5

3

w

w

w

ww

ZON

E41

64-8

0

APO

INT

A4”

LIN

E C

ON

TIN

UED

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

SG-5

226”

x 0.

562”

64-8

0

SG39

H29

SG39

H30

SG39

H38

SG39

H31

SG39

H36

w

B

B

B

B

CB

C

B

B

C

B

C

B

B

CB

SG-E

-522

-DA

BA

-4”

6” n

ozzl

e to

Red

ucer

152

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 153: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 65

BLO

WD

OW

NST

EAM

GEN

ERA

TOR

#2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-14

0

ZON

E67

47

V 290

LIN

E #

DIA

/SC

HFR

OM

TO

SG-0

486”

x 0.

562”

65-1

65-5

2

65-3

5

65-4

465

-43

65-4

2

65-4

165

-40

65-3

8

65-6A

65-7

65-9

65-8

65-2

165

-20

65-1

9

65-5

3

65-5

265

-51

65-4

9

65-4

8

65-5

0

65-4

5

65-3

765

-36 65

-34

65-3

365

-31

65-3

0

65-1

8

65-1

765

-15

65-1

4

65-1

0

65-1

1

65-1

365

-29

65-3

65-4

65-5

65-6

65-1

65-2

65-2

2

65-2

465

-23

65-2

5

65-2

8

65-2

665

-27

HV 44

HV 42

SG48

H11

SG48

H5

SG48

H14

SG48

H10SG

48H

27

WSG

52H

5

W

WSG

48H

16

SG48

H18

SG48

H21

SG48

H23

SG48

H24

EL. 1

09’

UV

500R

ZON

E 42

SG-0

526”

x 0.

562”

65-1

565

-28

SG-5

236”

x 0.

562”

64-8

9

65-8

9

ZON

E42

EL. 1

22’

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

W

SG48

H29

SG48

H30

SG48

H31

W

WW

A

POIN

T A

4” L

INE

CO

NTI

NU

ED

SG-E

-048

-DA

BA

-6”

SG-E

-523

-DA

BA-4

SG-E

-052

-DA

BA

-6” B

B

B

BB

C

B

B

BC

B

C

B

A

SG-E

-048

-DA

BA

-6”

6” n

ozzl

e to

Red

ucer

153

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 154: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 66

BLO

WD

OW

NST

EAM

GEN

ERA

TOR

#1

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

7

SG-E

-039

-DA

BA

-6”

EL. 1

08’ -

8”

ZON

E64

46

UV

500Q

C

LIN

E #

DIA

/SC

HFR

OM

TO

SG-3

96”

x.56

2”66

-166

-15

66-1

5

SG-E

-039

-DA

BA

-6”

EL. 1

08’ -

8”

C

EL. 1

06’-

0”C

TUR

BIN

EB

UIL

DIN

G

66-1

4

66-1

3

66-1

066

-9

66-7

66-5

66-1

166

-12

66-6

66-3

66-8

66-2

566

-1

66-2

154

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 155: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 67

BLO

WD

OW

NST

EAM

GEN

ERA

TOR

#2

PLA

NT

NO

RTH

REF

EREN

CE

DR

AWIN

GS

03-P

-SG

F-15

7

EL. 1

08’ -

8”

SG-E

-48-

DA

BA

-6”

EL. 1

08’ -

8”

ZON

E65

47

UV

500S

C

C

LIN

E #

DIA

/SC

HFR

OM

TO

SG-4

86”

x.56

2”67

-167

-12

67-1

2

67-1

0

67-1

1

67-5

67-8

67-6

67-9

67-7

67-2

67-3

67-1

67-2

2

155

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 156: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 68

REG

ENER

ATI

VE

HEA

T EX

CH

AN

GER

NO

TES:

Tag

No.

3M

CH

EE01

Seria

l No.

793

14 (A

MET

EK)

N.B

. No.

630

Ref

eren

ce D

raw

ings

:N

001-

7.03

-1N

001-

7.03

-48

thru

50

1110

WW

TOP

LON

G S

EAM

SN

EAR

& F

AR

SID

E

8” S

CH

160

PIP

EA

ND

FIT

TIN

GS

INLE

T

OU

TLET

VIEW FACING HEAT EXCHANGERLOOKING PLANT SOUTH

68-4

68-3

68-7

68-8

68-5

68-6

68-2

68-9

68-1

BB

156

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 157: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 69

LETD

OW

NH

EAT

EXC

HA

NG

ER

NO

TES:

Tag

No.

3M

CH

NE0

2Se

rial N

o. N

2376

(Ric

hmon

d En

gr)

N.B

. No.

784

54

Ref

eren

ce D

raw

ings

:N

001-

7.03

-26

N00

1-7.

03-2

7N

001-

7.03

-28

N00

1-7.

03-2

9

Tube

shee

t

Cha

nnel

head

Cro

ss S

ectio

n

32 S

tuds

1” x

9 3

/4”

3/4”

69-1 69

-2

157

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 158: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 70

LPSI

PU

MP

RO

OM

“A”

SUC

TIO

N

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-201

SI-2

41

H-2

0

V-2

01

SI-3

07

H-1

6

SI-6

7

H-4

70-5

6

70-5

8

70-5

9

70-6

0

70-6

1

70-6

370

-64

70-6

6

70-6

5

70-6

8

70-6

9

70-4

6

70-4

4

70-4

770

-55

70-5

3

70-1

03

70-5

2

70-5

0

70-4

9

70-1

0470-1

06

70-1

07

70-1

09ZO

NE

76

EL. 4

7’ 1

0”

EL. 4

1’ 1

0”

LPSI

PUM

P A

SUC

TIO

N (Z

one

72)

ZON

E 94

SI-A

-307

-GC

BC

-20”

SI-A

-307

-GC

BC

-14”

SI-A

-067

-GC

BC

-16”

LIN

E #

DIA

X S

CH

FRO

MTO

SI-6

7

SI-2

41

SI-3

07

SI-3

07

16”

X 0

.312

18”

X 0

.312

14”

X 0

.312

20”

X 0

.375

70-1

03

70-4

4

70-6

3

70-4

9

70-1

09

70-4

7

70-6

9

70-6

1

SI-A

-241

-GC

BC

-18”

ZON

E 10

2

W

W

W B

B

B

158

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 159: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 71

LPSI

PU

MP

RO

OM

“A

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-207

V-4

35

SI-8

7

H-3

ZON

E 76

SI-A

-087

-FC

BA

-10”

LIN

E #

DIA

X S

CH

FRO

MTO

SI-7

8

SI-8

7

SI-8

7

10”

X 0

.365

8” X

0.3

22”

10”

X 0

.365

72-2

9

72-5

72-8

72-3

2

72-6

72-5

7

72-3

2

72-3

0

74-4

5

72-2

9

72-2

7

72-2

6

72-2

3

72-2

4

72-2

1

72-2

072

-18

72-1

572

-17

72-1

4

72-1

2

72-1

1

72-9

72-8

72-6

72-5

74-5

274

-54

74-5

1

74-4

9

74-4

8 74-4

6

74-5

7

74-5

5

ZON

E 83

V-4

34

HV

-306

SI-8

7

H-2

SI-7

8

H-1

SI-8

7

H-1

SI-8

7

H-1

1

SI-A

-078

-FC

BA

-10”

SI-A

-087

-FC

BA

-10”

LPSI

PUM

P A

DIS

CH

AR

GE

Zone

72

EL 4

6’-9

TOG

EL.

51’-

6”

EL 6

2’-9

EL 6

2’-9

W

DIS

CH

AR

GE

SI-7

8

H-3

W

W

W

B

B

B

B

CB

SI-A

-087

-FC

BA

-8”

159

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 160: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 72

LPSI

PU

MP

A

REF

EREN

CE

DR

AWIN

GS

N00

1-11

.01-

36

72-3

AW

72-3

CW

72-3

BW

VIE

W L

OO

KIN

G D

OW

N

WEL

DED

SU

PPO

RT

FEET

AN

D S

UPP

OR

T C

OLU

MN

S

TWEN

TY-F

OU

R 2

” D

IAM

ETER

STU

DS

(21

@ 9

.5”

LON

G A

ND

3 @

8.8

8” L

ON

G)

DIS

CH

AR

GE

ZON

E 71

SUC

TIO

NZO

NE

70

N00

1-11

.01-

50

NO

TES:

1) T

AG

NU

MB

ER: 3

MSI

AP0

1

2) S

ERIA

L N

UM

BER

: 087

6-44

ING

ERSO

L R

AN

D

3) N

ATIO

NA

L B

OA

RD

NU

MB

ER: 5

23

B

BB

160

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 161: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 73

LPSI

PU

MP

RO

OM

“B”

SUC

TIO

N

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-202

V-2

00

C/L

EL.

41’

10”

LPSI

PUM

P B

SUC

TIO

N Z

one

75

SI-B

-308

-GC

BC

-20”

LIN

E #

DIA

X S

CH

FRO

MTO

SI-3

08

SI-3

08

SI-1

94

SI-3

4

14”

X 0

.312

20”

X 0

.375

18”

X 0

.312

16”

X 0

.312

71-6

3

71-4

9

71-4

4

71-1

05

71-6

9

71-6

1

71-4

7

71-1

11

SI-3

08

H-1

2

SI-3

08

H-1

3

71-5

071

-105

71-1

07

71-4

9

71-1

08

71-1

10

71-4

6

71-4

4

71-5

2

71-1

11

71-4

7

71-5

371

-55

71-5

671

-58

71-5

9

71-6

071-6

1

71-6

4

71-6

5

71-6

3

71-6

671-6

8

71-6

9SI

-B-3

08-G

CB

C-1

4”

SI-B

-194

-GC

BC

-18”

SI-3

4

H-4

SI-B

-034

-GC

BC

-16”

ZON

E 95

ZON

E 79

ZON

E 10

4

W

W

B

B

B

161

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 162: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 74

LPSI

PU

MP

RO

OM

“B

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-208

V-4

47

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

29

SI-1

29

SI-1

23

8” X

0.3

22”

10”

X 0

.365

10”

X 0

.365

73-5

73-8

73-2

7

73-6

75-5

1

73-3

0

73-2

8

75-3

9

73-2

7

73-2

5

73-2

4

73-2

1

73-2

2

73-1

9

73-1

773

-15

73-1

273-1

4

73-1

1

75-4

8

75-4

0

75-5

1

75-4

9

ZON

E 86

V-4

46

HV

-307

SI-1

29

H-5

SI-1

29

H-6

SI-1

29

H-1

SI-B

-123

-FC

BA

-10”

SI-B

-129

-FC

BA

-10”

LPSI

PUM

P B

DIS

CH

AR

GE

Zone

75

EL 4

6’-9

EL 6

2’-9

SI-1

29

H-4

73-9

73-8

EL 6

2’-9

ZON

E 79

75-4

6

75-4

5

75-4

3

75-4

2

73-6

73-5

SI-1

29

H-2

SI-1

29

H-3

73-3

0

DIS

CH

AR

GE

73-8

A

W

WW

CC

B

C

B

B

162

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 163: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 75

LPSI

PU

MP

B

REF

EREN

CE

DR

AWIN

GS

N00

1-11

.01-

36

73-3

AW

73-3

CW

73-3

BW

VIE

W L

OO

KIN

G D

OW

N

WEL

DED

SU

PPO

RT

FEET

AN

D S

UPP

OR

T C

OLU

MN

S

TWEN

TY-F

OU

R 2

” D

IAM

ETER

STU

DS

(21

@ 9

.5”

LON

G A

ND

3 @

8.8

8” L

ON

G)

DIS

CH

AR

GE

ZON

E 74

SUC

TIO

NZO

NE

73

N00

1-11

.01-

50

NO

TES:

1) T

AG

NU

MB

ER: 3

MSI

BP0

1

2) S

ERIA

L N

UM

BER

: 087

6-45

ING

ERSO

L R

AN

D

3) N

ATIO

NA

L B

OA

RD

NU

MB

ER: 5

24

B

BB

163

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 164: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 76

CO

NTA

INM

ENT

SPR

AY

PUM

P R

OO

M “

A”

SUC

TIO

N

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-201

V-1

57

SI-9

H-4

EL. 4

1’ 1

0”

CO

NTA

INM

ENT

SPR

AY

PU

MP

ASU

CTI

ON

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

67

SI-0

67

SI-0

09

SI-0

09

16”

X 0

.312

14”

X 0

.312

14”

X 0

.312

18”

X 0

.312

70-1

10

70-1

13

80-1

80-5

70-1

11

80-1

6

80-4

80-1

3

03-P

-SIF

-207

V-1

84

70-1

11

72-3

5

72-3

370

-114

70-1

10

70-1

1380

-19

80-1

8

80-1

7

80-1

6

80-1

0

80-6

80-2

0

80-1

3

80-1

2

80-9

80-1

1

80-8

80-7

80-4

80-5

80-3

80-2

80-1

SI-6

7

H-3

SI-6

7

H-2

SI-6

7

H-1

ZON

E 70

ZON

E 71

ZON

E 82

EL. 7

0’

EL. 4

7’ 1

0”

SI-A

-009

-GC

BC

-18”

SI-A

-078

-FC

BA

-10”

SI-0

7810

” X

0.3

65”

72-3

372

-35

SI-A

-067

-GC

BC

-14”

W

SI-A

-009

-GC

BC

-14”

ZON

E 10

2

W

B

B

B

BSI

-A-0

67-G

CB

C-1

6”

ZON

E 78

164

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 165: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 77

CO

NTA

INM

ENT

SPR

AY

PUM

P R

OO

M “

A”

DIS

CH

AR

GE

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-207

*A

nnub

ar M

od

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

79

SI-0

79

SI-0

82

8” X

0.3

22”

10”

X 0

.365

10”

X 0

.365

82-1

A

82-1

82-3

1

-

82-2

7

82-3

5

HV

-684

SI-A

-082

-FC

BA

-10”

V-4

85

82-2

7

82-2

6

82-2

482

-22

82-2

582

-20

82-2

1

82-1

9

82-1

8

82-1

7

82-1

3

82-6

82-2

3

82-3

1

82-1

6

82-1

2

82-1

4

82-1

1

82-1

0

82-5

82-9

77-6

0

82-7

82-4

82-3

82-2

82-1

82-1

A

SI-7

9

H-9

SI-7

9

H-5

SI-7

9

H-8

SI-7

9

H-6

SI-7

9

H-7

SI-7

9

H-3

SI-7

9

H-2

SI-7

9

H-4

SI-A

-079

-FC

BA

-10”

SI-A

-079

-FC

BA

-10”

SI-8

2

H-2

82-3

3

82-3

4

82-3

282

-35

CO

NTA

INM

ENT

SPR

AY P

UM

P A

DIS

CH

AR

GE

ZON

E 82

ZON

E 83

TOG

EL 5

1’-6

EL 7

0’

W

EL 7

0’

EL 5

3’-6

EL 5

8’-6

82-1

5

82-2

A

W

W

W

W

W

77-6

277

-61

SI-0

79*

10”

X 0

.365

”77

-60

77-6

2

BBB

BC

B

B

C

B

SI-A-

079-F

CBA-

8”

ZON

E 78

165

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 166: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 78

CO

NTA

INM

ENT

SPR

AY

PU

MP

A

REF

EREN

CE

DR

AWIN

GS

N00

1-11

.01-

36

80-3

AW

80-3

CW

80-3

BW

VIE

W L

OO

KIN

G D

OW

N

WEL

DED

SU

PPO

RT

FEET

AN

D S

UPP

OR

T C

OLU

MN

S

TWEN

TY-F

OU

R 2

” D

IAM

ETER

STU

DS

(21

@ 9

.5”

LON

G A

ND

3 @

8.8

8” L

ON

G)

DIS

CH

AR

GE

ZON

E 77

SUC

TIO

NZO

NE

76

NO

TES:

1) T

AG

NU

MB

ER: 3

MSI

AP0

3

2) S

ERIA

L N

UM

BER

: 087

6-46

ING

ERSO

L R

AN

D

3) N

ATIO

NA

L B

OA

RD

NU

MB

ER: 5

21

B

BB

166

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 167: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 79

CO

NTA

INM

ENT

SPR

AY

PUM

P R

OO

M “

B”

SUC

TIO

N

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-202

V-1

85

CO

NTA

INM

ENT

SPR

AY

PU

MP

BSU

CTI

ON

ZO

NE

81

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

33

SI-0

33

SI-0

34

SI-0

34

14”

X 0

.312

18”

X 0

.312

14”

X 0

.312

16”

X 0

.312

81-1

81-5

81-1

5

71-1

03

81-4

81-1

2

71-1

01

71-1

04

03-P

-SIF

-208

71-1

04

SI-B

-033

-GC

BC

-18”

SI-1

2310

” X

0.3

65”

73-3

173

-33

V-1

5873

-33

81-1

2

81-1

9

81-1

8

81-1

7 81-1

1

81-1

6

81-1

0

81-9

81-8

81-1

5

81-7

81-6

81-5

81-4

81-3

81-2

81-1

71-1

03

71-1

01

71-1

00

73-3

1

SI-3

3

H-4

SI-3

4

H-3

SI-3

4

H-1

SI-3

4

H-6

SI-B

-034

-GC

BC

-14”

SI-B

-033

-GC

BC

-14”

SI-B

-034

-GC

BC

-16”SI

-B-1

23-F

CB

A-1

0”

ZON

E 73

ZON

E 74

ZON

E 85

EL 7

0

EL 4

1’-1

0”

EL 4

7’-1

0”

ZON

E 10

4

W

C

BB

B

167

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 168: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 80

CO

NTA

INM

ENT

SPR

AY

PUM

P R

OO

M “

B”

DIS

CH

AR

GE

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-208

*A

nnub

ar M

od

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

19

SI-1

19

SI-1

47

8” X

0.3

22”

10”

X 0

.365

10”

X 0

.365

83-1

A

83-1

83-3

0

-

83-2

6

83-3

4

V-4

84

SI-1

19

H-7

SI-B

-119

-FC

BA

-10”

HV

-689

SI-B

-147

-FC

BA

-10”

SI-B

-119

-FC

BA

-10”

83-1

83-1

1

83-2

83-1

A

83-3

83-5

83-1

2

83-4

83-6

80-6

0

83-1

3

83-9

83-1

4

83-3

4

83-3

2

83-8

83-1

0

83-3

3

83-3

1

83-1

5

83-3

0

83-1

6 83-1

8

83-1

7

83-1

9

83-2

0

83-2

2

83-2

3

83-2

4

83-2

5

83-2

6

CO

NTA

INM

ENT

SPR

AY

PU

MP

BD

ISC

HA

RG

E

ZON

E 86

ZON

E 85

EL 5

8’-6

TOG

EL 5

1’ 6

EL 7

0’

EL 7

0’

83-2

1

EL 6

3’-0

EL 5

3’-6

EL 4

9’-2

SI-1

19

H-9

SI-1

19

H-8

SI-1

19

H-6

SI-1

19

H-2

SI-1

19

H-1

SI-1

19

H-3

SI-1

19

H-4

SI-1

19

H-5

W

SI-1

47

H-1

80-6

280-6

1

W

WW

SI-1

19*

10”

X 0

.365

”80

-60

80-6

2

C

B

B C

B

BC

B

C

C

ZON

E 81

168

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 169: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 81

CO

NTA

INM

ENT

SPR

AY

PU

MP

B

REF

EREN

CE

DR

AWIN

GS

N00

1-11

.01-

36

81-3

AW

81-3

CW

81-3

BW

VIE

W L

OO

KIN

G D

OW

N

WEL

DED

SU

PPO

RT

FEET

AN

D S

UPP

OR

T C

OLU

MN

S

TWEN

TY-F

OU

R 2

” D

IAM

ETER

STU

DS

(21

@ 9

.5”

LON

G A

ND

3 @

8.8

8” L

ON

G)

DIS

CH

AR

GE

ZON

E 80

SUC

TIO

NZO

NE

79

NO

TES:

1) T

AG

NU

MB

ER:3

MSI

BP0

3

2) S

ERIA

L N

UM

BER

: 087

6-47

ING

ERSO

L R

AN

D

3) N

ATIO

NA

L B

OA

RD

NU

MB

ER: 5

22

B

BB

169

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 170: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 82

SHU

TDO

WN

CO

OLI

NG

HEA

TEX

CH

AN

GER

RO

OM

A

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-207

HV

-685

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

78

SI-0

78

SI-0

79

10”

X 0

.365

20”

X 0

.500

10”

X 0

.365

72-3

6

72-4

9

82-2

8

72-4

8

72-5

2

72-6

1

HV

-678

SI-A

-078

-FC

BA

-20”

SI-7

8

H-4

W

72-5

2

72-4

9

72-4

9B

72-4

8

72-4

772

-45

72-4

472

-42

72-4

1

72-3

9

72-3

8

72-3

6

72-5

0

72-4

9C

72-6

0

72-6

1

72-5

8

72-5

772

-55

72-5

4

82-3

0

82-2

9

82-2

8

SI-7

9

H-1

0

CS/

SS

SI-A

-078

-FC

BA

-10”

SI-A

-079

-FC

BA

-10”

ZON

E 77

ZON

E 76

SDC

HX

AIN

LET

NO

ZZLE

72-4

9D

WB

B

ZON

E 84

170

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 171: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 83

SHU

TDO

WN

CO

OLI

NG

HEA

TEX

CH

AN

GER

RO

OM

A

REF

EREN

CE

DR

AWIN

GS

03-P

-PC

F-20

1

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

70

SI-0

70

SI-0

70

20”

X 0

.500

16”

X 0

.375

20”

X 0

.500

74-1

74-2

1

74-2

7

74-1

9

74-2

5

74-2

7

V-4

58

74-9

8

SI-A

-090

-FC

BA

-14”

03-P

-SIF

-203

03-P

-SIF

-207

SI-0

82

SI-0

87

SI-0

89

10”

X 0

.365

10”

X 0

.365

10”

X 0

.365

82-3

6

74-5

8

74-7

7

82-3

8

74-7

4

74-8

7

SI-0

8910

” X

0.3

65”

82-3

982

-44

SDC

HX

AO

UTL

ETN

OZZ

LE

ZON

E 77

ZON

E 94

ZON

E 94

ZON

E 71

SI-8

9H

-3

SI-8

7H

-4

SI-8

7H

-5

SI-8

7H

-8

SI-8

7H

-7

SI-8

7H

-6

SI-8

7H

-9

SI-8

2H

-1

SI-8

9H

-2

SI-8

9H

-1

W

SI-9

0H

-1

W

SI-9

0H

-2

SI-9

0H

-4

SI-7

0H

-6

SI-7

0H

-7

SI-7

0H

-2

SI-7

0H

-3

W

SI-7

0H

-1

W

74-2

7

74-7

5

74-2

5

74-2

4

74-2

2

74-1

9

74-1

04A

74-2

1

74-1

874

-16

74-1

5

74-9

6

74-1

3

74-1

0

74-7

6

74-1

274-9

74-7

74-6

74-4

74-3

74-1

74-9

7

74-5

874-6

3

74-6

1

74-6

7

74-1

18

74-1

17

74-1

12

74-1

14

74-1

1574

-109

74-1

11

74-1

08

74-1

06

74-1

05

74-6

4

74-6

074

-66

74-6

9

74-7

0

74-7

1

74-7

3

74-7

4

82-3

9

82-4

2

82-3

6

82-3

882

-37

74-7

7

74-1

00

74-9

9

74-8

6

74-8

0

74-7

8

74-8

3

74-8

4

74-8

182

-43

82-4

4 82-4

1

82-4

0

74-8

7

HV

-657

HV

-687

HV

-686

HV

-688

V-4

60

SI-A

-070

-FC

BA

-20”

SI-A

-087

-FC

BA

-10”

SI-E

-131

-FC

BA

-6”

SI-A

-089

-FC

BA

-10”

SI-A

-082

-FC

BA

-10”

CS/

SS

SI-0

9014

” X

0.3

75”

74-1

0574

-118

SI-1

316”

X 0

.280

”74

-97

74-1

00

W

W

W

W

W

W

W

SI-8

9H

-5

B

B

B

B

CB

B

C

B

A

C

B

B

C

B

B

C

B

B

ZON

E84

SI-A

-070

-FC

BA

-16”

171

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 172: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 84

SHU

TDO

WN

CO

OLI

NG

HEA

T EX

CH

AN

GER

A

74-1

21

74-1

22

74-1

24

74-1

23

+ IR

INLE

T N

OZZ

LE -

ZON

E 82

+ IR

OU

TLET

NO

ZZLE

(OPP

OSI

TE S

IDE)

- ZO

NE

83

NO

TES:

1) T

AG

NU

MB

ER: 3

MSI

AE0

1

2) S

ERIA

L N

UM

BER

: S-1

8345

(E

NG

R &

FA

BR

ICA

TOR

S)

3) N

ATI

ON

AL

BO

AR

D N

UM

BER

153

2

4) Z

ERO

DEG

REE

FO

R G

IRTH

WEL

DS

IS

TD

C. 9

0 D

EGR

EE IS

AT

INLE

T

NO

ZZLE

SID

E.

REF

EREN

CE

DR

AW

ING

S:

N00

1-7.

03-0

20N

001-

7.03

-25

30 d

eg.

30 d

eg.

Inco

nel W

eld

SA-1

05

Cla

d

74-1

2175

-122

DET

AIL

for N

OZZ

LE to

PIP

E

N00

1-11

.01-

209

TUB

E SH

EET

CH

AN

NEL

HEA

D C

RO

SS S

ECTI

ON

1/8”

CLA

D1-

7/16

64 S

TUD

S1.

5” X

17”

172

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 173: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 85

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-208

HV

-694

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

19

SI-1

23

SI-1

23

10”

X 0

.365

10”

X 0

.365

20”

X 0

.500

83-2

7

73-3

4

73-4

8

73-6

3

73-4

6

73-5

4 HV

-679

SI-1

19

H-1

4

SI-B

-123

-FC

BA

-10”

SI-1

19

H-1

3

SI-1

19

H-1

1

SI-1

19

H-1

0

SI-1

23

H-2

SI-1

23

H-8

SI-1

23

H-5

SI-1

23

H-6

SI-1

23

H-7

73-6

273

-63

73-6

0

73-5

9

73-5

7

73-5

6

83-2

9

83-2

8

73-3

4

83-2

7

73-3

6

73-3

7

73-4

0

73-3

9

73-4

273-4

5

73-8

3

73-4

373

-46

73-4

8

73-4

7

73-6

4

73-4

9

73-5

1

73-5

2

SI-B

-123

-FC

BA

-20”

SI-B

-119

-FC

BA

-10”

73-5

4C

S/SS

ZON

E 80

ZON

E 79 SD

CH

X B

INLE

T N

OZZ

LE

T O

F EL

70’

T O

F EL

70’

EL 7

5’

EL 7

5’

EL 8

0’-2

EL 8

0’-2

SHU

TDO

WN

CO

OLI

NG

HEA

TEX

CH

AN

GER

RO

OM

B

SI-1

23

H-1

W

W

W

W

WW

B

B

C

B

B

C

B

B

BB

ZON

E 87

173

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 174: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 86

SHU

TDO

WN

CO

OLI

NG

HEA

T

REF

EREN

CE

DR

AWIN

GS

03-

P-PC

F-20

1

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

72

SI-0

72

SI-0

72

20”

X 0

.500

16”

X 0

.375

20”

X 0

.500

75-1

75-1

9

75-2

5

75-1

7

75-2

3

75-2

5

HV

-696

SI-B

-147

-FC

BA

-10”

SI-1

29

SI-1

31

SI-1

34

10”

X 0

.365

6” X

0.2

80”

10”

X 0

.365

75-5

3

75-8

1

75-6

2

75-6

1

75-8

4

83-4

3

SI-1

35

SI-1

47

14”

X 0

.375

10”

X 0

.365

75-8

7

83-3

5

75-1

00

83-3

7

SI-7

2H

-3

SI-7

2H

-4

SI-7

2H

-2

SI-7

2H

-1

W

SI-7

2H

-12

W

SI-7

2H

-5

SI-7

2H

-6

SI-1

47H

-2

SI-1

34H

-8

SI-1

34H

-3

SI-1

34H

-2

SI-1

34H

-1

SI-1

34H

-6

SI-1

34H

-5SI

-134

H-7

SI-1

35H

-1

SI-1

35H

-3SI

-135

H-2

SI-1

29H

-11

SI-1

29H

-10

SI-1

29H

-12

SI-1

29H

-9

SI-1

29H

-8

SI-1

29H

-7

SI-1

29H

-13

75-5

875

-60

75-1

4

75-2

6

75-2

5

75-2

3

75-9

0

75-5

5

75-2

2

75-2

0

75-8

8

75-1

9

75-9

175

-99

75-5

6

75-1

7

75-1

6

75-8

7

75-9

6

75-1

00

75-1

3

75-9

3

75-8

1

75-8

2

75-1

2

75-8

3

75-1

29

75-1

1

75-8

75-9

7 75-8

4

75-9

75-7

2

75-7

175-6

975-6

8

75-775

-66

75-6

5

75-6

3

75-5

75-6

2

75-275

-4

75-1

75-5

483

-36

75-5

3

75-6

1

75-9

4

83-3

7

83-3

8

83-3

9

83-4

2

83-4

3

83-3

5

83-4

0

83-4

1

ZON

E 80

SDC

HX

BO

ULL

ETN

OZZ

LE

ZON

E 74

ZON

E 95

ZON

E 95

SI-B

-129

-FC

BA

-10”

SI-B

-135

-FC

BA

-14”

SI-B

-072

-FC

BA

-20”

HV

-695

HV

-693

V-4

64 V-4

55

HV

-658

SI-B

-134

-FC

BA

-10”

03-P

-SIF

-204

03-P

-SIF

-208

EXC

HA

NG

ER R

OO

M B

75-1

25

75-1

27

WW

W

W

W

W

W

W

W

W

C

B

C

CCC

C

B

B

C

B B

C

B

B

C

C

C B

B

C

B

C

C

C

ZON

E 87

SI-E

-131

-FC

BA

-6”

174

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 175: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 87

SHU

TDO

WN

CO

OLI

NG

HEA

T EX

CH

AN

GER

B

75-7

6

75-7

7

75-7

9

75-7

8

+IR

INLE

T N

OZZ

LE -

ZON

E 85

+IR

OU

TLET

NO

ZZLE

(OPP

OSI

TE S

IDE)

- ZO

NE

86

NO

TES:

1) T

AG

NU

MB

ER: 3

MSI

BE0

1

2) S

ERIA

L N

UM

BER

: S-1

8346

(E

NG

R &

FA

BR

ICA

TOR

S)

REF

EREN

CE

DR

AW

ING

S:

N00

1-7.

03-0

20N

001-

7.03

-25

3) N

ATI

ON

AL

BO

AR

D N

UM

BER

159

9

4) Z

ERO

DEG

REE

FO

R G

IRTH

WEL

DS

IS

TD

C. 9

0 D

EGR

EE IS

AT

INLE

T

NO

ZZLE

SID

E.

30 d

eg.

30 d

eg.

Inco

nel W

eld

SA-1

05

Cla

d

75-7

675

-77

DET

AIL

for N

OZZ

LE to

PIP

E

N00

1-11

.01-

209

TUB

E SH

EET

CH

AN

NEL

HEA

D C

RO

SS S

ECTI

ON

1/8”

CLA

D1-

7/16

64 S

TUD

S1.

5” X

17”

175

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 176: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 88

EAST

WR

AP

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

72

SI-0

72

SI-0

72

12”

X 0

.375

12”

X 1

.125

20”

X 0

.500

78-2

78-1

3

75-3

5

78-1

1

78-1

4

75-3

8

SI-E

-174

-CC

BA

-12”

SI-0

73

SI-0

73

SI-1

55

12”

X 0

.375

12”

X 1

.125

12”

X 1

.125

79-1

79-1

3

78-1

6

79-1

1

79-1

4

78-2

1

SI-1

72

SI-1

74

10”

X 0

.365

12”

X 1

.125

78-1

0C

79-1

6

78-1

0D

79-2

1

03-P

-SIF

-208

17

18

79-1

79-7

79-6

79-8

79-1

0

79-1

3

79-1

1

79-1

479

-16

79-1

7

79-1

8

79-1

9

79-2

0

79-2

1

75-3

8

75-3

6

75-3

7

75-3

5

78-1

3

78-1

0K

78-1

0J

78-1

1

78-1

0C

78-2

0

78-1

0B

78-1

9

78-1

0A

78-9

J

78-8

78-2

1

78-1

8

78-1

7

78-1

0D

78-1

6

78-9

G

78-9

F78-7

78-1

4

78-9

K

78-9

C

78-6

78-9

78-5

78-3

78-2

ZON

E 89

ZON

E 98

ZON

E 99

SI-7

3H

-1

SI-7

2H

-16

SI-7

2H

-17

SI-7

2H

-15

SI-7

2H

-11

SI-7

2H

-14

SI-7

2H

-13

SI-7

2H

-18

SI-7

2H

-22

SI-7

2H

-21

SI-7

2H

-20

w

SI-7

3H

-3SI

-73

H-2

UV

-615

HV

-690

UV

-625

SI-B

-073

-FC

BA

-12”

SI-B

-072

-FC

BA

-20”

SI-E

-155

-CC

BA

-12”

SI-E

-172

-FC

BA

-10”

SI-7

2H

-19

78-6

0

78-5

8ZO

NE

95

W

W

W

CC

C

B

C

B

CBB

C

C

CB

C

176

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 177: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 89

EAST

WR

AP

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-202

SI-1

73H

-1

w

HV

-690

SI-E

-173

-GC

BC

-16”26

03-P

-SIF

-208

SI-1

94H

-13

SI-1

94H

-12

SI-1

94H

-14

SI-1

94H

-23

71-8

171

-84

71-8

5

71-8

7A

71-9

4

71-7

71-7

1

71-9

3

71-7

3

71-7

5

71-9

1

71-7

8

71-9

0

71-1

8

71-7

0

71-7

6

71-7

9

71-8

2

71-1

6

71-8

8

71-1

371

-5

71-1

471

-11

71-1

0

71-8

71-4

71-2

71-1

ZO

NE

88

TOG

87’-

3”

SI-B

-038

-GC

BC

-12”

SI-B

-194

-GC

BC

-18”

SI-B

-194

-GC

BC

-16”

ZON

E 10

1

ZON

E 95

UV

-656

V-4

42

LIN

E #

DIA

X S

CH

FRO

MTO

SI-3

8

SI-1

73

SI-1

73

12”

X 0

.250

16”

X 0

.312

10”

X 0

.250

71-9

0

71-7

0

71-7

3

71-9

4

71-7

1

71-8

7A

SI-1

73

SI-1

94

10”

X 0

.365

16”

X 0

.312

71-8

8

71-1

-

71-1

1

SI-1

9418

” X

0.3

12”

71-1

371

-18

W

W

C

B

BB

B

SI-E

-173

-GC

BC

-10”

177

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 178: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 90

EAST

WR

AP

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-202

SI-1

34H

-10

UV

-671

2403

-P-S

IF-2

08

ZON

E 10

1

ZON

E 95

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

30

SI-1

34

SI-1

34

24”

X 0

.375

10”

X 0

.365

8” X

0.3

22”

85-6

83-5

3

83-5

8

85-8

R

83-5

7

83-5

9

SI-3

0824

” X

0.5

62”

85-9

85-1

1

SI-1

34H

-9

V-2

06

UV

-676

85-1

1

85-9

85-6

85-8

R

83-5

983

-53

83-5

4

83-5

883

-55

83-5

6

83-5

7

SI-B

-308

-GC

BC

-24”

SI-B

-030

-HC

BA

-24”

SI-B

-134

-FC

BA

-10”

EL 7

3’-7

EL 9

5’

ZON

E 10

4

W

22ZO

NE

121

SI-B

-130

-GC

BC

-10”

SI-1

3010

” X

0.2

50”

90-4

290

-46

90-4

1

90-4

2

90-4

3

90-4

4

90-4

5

90-4

6

90-4

0

SI-1

30H

-2

SI-1

3010

” X

0.2

50”

90-4

090

-41

B

B

B

90-5

0

R15

WO

318

7448

90-5

0, 8

5-8R

NO

TES:

SI-B

-130

-GC

BC

-8”

SI-B

-134

-FC

BA

-8”

178

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 179: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 91

WES

T W

RA

P

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-207

UV

-645

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

70

SI-0

70

SI-0

70

SI-0

71

20”

X 0

.500

12”

X 0

.375

12”

X 1

.125

12”

X 0

.375

74-4

2

76-2

76-5

2

74-1

03

74-4

4

76-1

3

76-1

4

77-1

1

SI-7

1

H-3

SI-A

-070

-FC

BA

-12”

SI-0

7112

” X

1.1

25”

77-1

377

-14

SI-0

7110

” X

0.3

65”

77-1

0C77

-10D

SI-2

0212

” X

1.1

25”

76-1

676

-21

SI-2

2012

” X

1.1

25”

77-1

677

-21

UV

-635

HV

-691

76-1

1

76-2

76-3

76-5

76-6

76-7 76-8

76-1

3

76-1

0

76-1

4

76-1

6

76-1

7

76-1

8

76-1

976-2

0

76-2

1

SI-A

-202

-CC

BA

-12”

SI-A

-071

-FC

BA

-12”

SI-E

-220

-CC

BA

-12”

SI-A

-070

-FC

BA

-20”

74-4

2

77-7

74-4

3

74-1

03

74-1

04

74-1

02

77-8

77-1

6

77-1

3

77-1

1

77-2

1

77-1

0C

77-2

0

77-1

0D

77-1

9

77-1

0B

77-1

8

77-1

0A

77-1

4

77-1

0

77-1

7

SI-7

0

H-1

0

SI-7

1

H-2

SI-7

0

H-1

3

SI-7

0

H-1

1

W

SI-7

0

H-1

6

W

SI-7

0

H-1

4

SI-7

0

H-9

W

SI-7

0

H-1

5

74-4

4

ZON

E 94

ZON

E 97

ZON

E 96

TOG

EL 8

7’-3

TOG

EL 8

7’-3

TOG

EL 8

7-3”

TOG

EL 8

7’-3

ZON

E 92

SI-7

0

H-1

2

W

1920

76-5

2

76-5

1

B

B

B

C

B

B

B

CBC

SI-A

-071

-FC

BA

-10”

179

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 180: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 92

WES

T W

RA

P

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

02

SI-2

39

SI-2

39

12”

X 0

.250

10”

X 0

.250

10”

X 0

.365

70-8

5

70-7

0

70-8

3

70-9

8

70-8

2A

-

SI-2

41

SI-2

41

16”

X 0

.312

18”

X 0

.312

70-1

70-1

6

70-1

4

70-2

2

03-P

-SIF

-201

27

70-9

7

SI-2

39H

-1

SI-2

41H

-12

SI-2

41H

-21

w

HV

-691

SI-A

-002

-GC

BC

-12”

03-P

-SIF

-207

70-9

5

70-9

4

70-8

9

70-9

2

70-8

8

70-8

6

70-1

3

70-9

1

70-2

0

70-1

9

70-1

470

-17

70-1

1

70-1

0

70-7

3

70-2

2

70-8

5

70-1

6A

70-8

70-1

6

70-7

70-7

0

70-7

7

70-5

70-7

1

70-7

4

70-7

9

70-7

6

70-8

070

-82A

70-8

3

70-4

70-2

70-9

8

70-1

A70

-1

SI-2

39H

-2

SI-2

39H

-3

w

SI-2

41H

-14

SI-2

41H

-15

SI-2

41H

-11

SI-2

41H

-9

EL. 8

4’-3

EL 7

8’-9

EL 8

7’-3

”EL

87’

-3”

ZON

E 10

0

ZON

E 94

UV

-655

V-2

56

EL 7

0’

SI-E

-239

-GC

BC

-10”

SI-A

-241

-GC

BC

-16”

ZON

E 91

W

W

C

B

C

B

C

B

BB

C

SI-A-

241-G

CBC-

18”

180

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 181: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 93

WES

T W

RA

P

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-201

UV

-672

23

03-P

-SIF

-207

ZON

E 10

0

ZON

E 94

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

89

SI-0

89

SI-0

07

8” X

0.3

22”

10”

X 0

.365

24”

X 0

.375

82-6

6

82-5

5

84-6

82-6

7

82-6

5

84-8

R

SI-3

0724

” X

0.5

62”

84-9

84-1

1

SI-8

9H

-11

V-2

05

UV

-674

84-1

1

84-9

84-6

84-8

RSI

-A-3

07-G

CB

C-2

4”

EL 7

3’-7

82-5

5

82-5

6

82-5

7

82-5

882

-59

82-6

1

82-6

2

82-6

0

82-6

3

82-6

4

82-6

5

82-6

6

82-6

7

SI-8

9H

-10

SI-8

9H

-13

SI-8

9H

-12

W

EL 9

2’-6

EL 8

4’-8

TOG

EL 8

7’-3

TOG

EL 8

7’-3

SI-A

-089

-FC

BA

-10”

SI-A

-007

-HC

BA

-24”

ZON

E 10

2

SI-0

8810

” X

0.2

50”

93-4

293

-43

21ZO

NE

120

93-4

3 93-4

1

93-4

0

93-4

2

SI-A

-088

-GC

BC

-10”

8” X

0.2

50”

93-4

093

-41

SI-0

88

R15

WO

318

7454

93-5

0, 8

4-8R

NO

TES:

93-5

0

C B

B

B

181

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 182: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 94

A T

RA

IN M

ISC

. PIP

E C

HA

SES

AN

D 8

8’ P

IPE

TUN

NEL

REF

EREN

CE

DR

AWIN

GS;

03-P

-SIF

-201

03-P

-SIF

-207

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

70

SI-0

89

SI-2

41

20”

X 0

.500

10”

X 0

.365

18”

X 0

.312

74-2

8

82-4

5

70-2

3

74-4

1

82-5

4

70-4

3

SI-8

9H

-7

SI-A

-241

-GC

BC

-18”

SI-7

0H

-8

W

82-4

5

82-4

6

82-4

9

82-4

782

-48

82-5

0

82-5

1

82-5

2

82-5

3

82-5

4

SI-8

9H

-8

SI-8

9H

-9

SI-8

9H

-6

70-3

4

70-3

3

70-3

0

70-3

1

70-2

8

70-2

5

70-2

7

70-2

4

70-2

3

70-4

070

-41

70-4

370

-36

70-3

7

70-3

9

SI-2

41H

-8

SI-2

41H

-17

SI-2

41H

-7

SI-2

41H

-4SI

-241

H-3

SI-2

41H

-2

SI-2

41H

-5

SI-2

41H

-6

74-3

0

74-2

8

74-3

1

74-3

274

-34

74-3

5

74-3

7

74-3

8

74-4

0

SI-7

0H

-5

W

SI-7

0H

-4

74-4

1

SI-A

-089

-GC

BC

-10”

SI-A

-070

-FC

BA

-20”

EL 7

2’

EL 8

9’-4

EL 9

2’-6

EL 6

4’

EL 4

1’-1

0”

EL 9

0’-2

” ZON

E 83

ZON

E 91

ZON

E 93

ZON

E 92

ZON

E 70

EL 8

8’

ZON

E 83

74-1

65

74-1

63 70-1

95

70-1

9470

-190

W

W

W

W

WWW

B

B

B

B

B

B

B

B

C

B

BB

B

B

B

182

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 183: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 95

B T

RA

IN M

ISC

. PIP

E C

HA

SES

AN

D 8

8’ P

IPE

TUN

NEL

REF

EREN

CE

DR

AWIN

GS;

03-P

-SIF

-202

03-P

-SIF

-208

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

72

SI-1

34

SI-1

94

20”

X 0

.500

10”

X 0

.365

18”

X 0

.312

75-2

7

83-4

4

71-1

9

75-3

3

83-5

2

71-4

3

SI-1

94H

-6

W

SI-1

34H

-12

SI-B

-134

-FC

BA

-10”

71-4

071

-39

71-3

771

-36

71-2

6

71-3

4

71-4

3

71-3

3

71-3

2

71-2

5

71-4

1

71-3

0

71-2

9

71-2

3

71-2

7

71-2

2

71-2

0

71-1

9

SI-1

94H

-7

SI-1

94H

-2

SI-1

94H

-8SI-1

94H

-15

SI-1

94H

-4

SI-1

94H

-10

SI-1

94H

-21

SI-1

94H

-9

SI-1

94H

-11

SI-1

94H

-5

83-4

7

83-4

483

-45

83-4

6

83-4

983

-48

83-5

0

83-5

1

83-5

2

SI-1

34H

-11

75-3

3

75-3

1

75-3

0

75-2

9

75-2

7

SI-7

2H

-8SI

-72

H-1

0

SI-7

2H

-9SI

-72

H-7

EL 9

2’-6

ZON

E 88

EL 7

2’

ZON

E 86

EL 8

8’

ZON

E 86

ZON

E 90

EL 9

5’

EL 9

2’-1

ZON

E 73

EL 4

1’-1

0”

EL 8

9’-9

ZON

E 89

SI-B

-072

-FC

BA

-20”

SI-B

-194

-GC

BC

-18”

SI-1

34H

-4

71-2

12

W

W

W

W

W

W

W

W

B

B

B

BB

B

B

C

B

B

CB

C

B

C

B

B

B

183

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 184: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 96

CO

NTA

INM

ENT

LPSI

HEA

DER

TO

LO

OP

1A

V-5

42

ZON

E 91

LIN

E #

DIA

X S

CH

FRO

MTO

SI-2

02

SI-2

02

12”

X 1

.125

12”

X 1

.312

76-2

2

76-2

7

76-2

5

76-4

7

76-2

5

SI-2

02H

-17

SI-2

02H

-12

W

SI-E

-202

-CC

BA

-12”

19

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-103

A

A

SI-2

02H

-6

76-2

8

76-3

976-4

076

-4176-4

2

76-4

4

76-4

3

76-4

5

76-4

6

76-4

7

SI-2

02H

-18

SI-2

02H

-2

SI-2

02H

-4

SI-2

02H

-15

SI-2

02H

-3

SI-2

02H

-16

SI-2

02H

-1

76-3

0

76-3

1

76-2

7

76-3

2

76-3

4

76-2

9

76-3

5

76-3

7

76-3

3

76-3

8

76-3

6

76-2

3

76-2

276-2

4

SI-E

-202

-CC

BA

-12”

ZON

E 23

FL E

L 10

0’EL 8

9’-9

V-1

34

ZON

E 11

4

76-7

9

76-5

6

W

B

B

BB

B

BB

B

B

CB

SI-2

02H

-7

184

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 185: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 97

CO

NTA

INM

ENT

LPSI

HEA

DER

TO

LO

OP

1B

V-1

44

ZON

E 91

LIN

E #

DIA

X S

CH

FRO

MTO

SI-2

20

SI-2

20

12”

X 1

.125

12”

X 1

.312

77-2

2

77-2

7

77-2

5

77-4

7

SI-E

-220

-CC

BA

-12”

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-103

A

77-2

8C

20

A

ZON

E 24

EL 8

9’-9

SI-2

20H

-18

SI-2

20H

-15

SI-2

20H

-20

SI-2

20H

-17

SI-2

20H

-13

SI-2

20H

-12

SI-2

20H

-10

77-2

8B

77-3

8

77-3

9

77-3

1

77-3

4

77-3

0

77-2

8

77-2

8A

77-2

9

77-2

8D

77-3

7

77-3

5

77-3

6

77-3

277

-33

77-4

0

77-2

3

77-2

2

77-3

8A

77-2

577

-24

77-2

7

77-4

6

77-4

5

77-4

6B77

-46A

77-4

2

77-4

1

77-4

4

77-4

3

77-4

7

77-4

6F

77-4

6D

77-4

6C

77-4

6G77

-46E

SI-2

20H

-24

SI-2

20H

-8

SI-2

20H

-7

SI-2

20H

-23

SI-2

20H

-5SI-2

20H

-27

V-5

43

SI-E

-220

-CC

BA

-12”

SI-2

20H

-1

ZON

E 11

4

77-8

3

W

W

W

B

B

BB

BB

B

BB

B

B

B

B

SI-2

20H

-9SI

-220

H-1

9

BB

B

185

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 186: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 98

CO

NTA

INM

ENT

LPSI

HEA

DER

TO

LO

OP

2A

V-1

14

ZON

E 88

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

55

SI-1

55

12”

X 1

.125

12”

X 1

.312

78-2

2

78-2

7

78-2

5

78-4

7

SI-E

-155

-CC

BA

-12”

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-136

78-3

2

17

SI-1

55H

-7

SI-1

55H

-2

SI-1

55H

-6

SI-1

55H

-5

78-3

3

78-3

5

78-3

4

78-3

878

-39 78

-37

78-4

2

78-3

6

78-4

0

78-4

1

78-4

4

78-4

3

78-4

578-4

6

78-4

7

78-3

0

78-2

9

78-2

8

78-2

5

78-2

7

78-2

478

-23

78-2

2

78-3

1

ZON

E 25

V-5

40

FL E

L10

0’

EL 8

9’-9

ZON

E 11

5

78-7

8

W

W

BB

B

B

186

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 187: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 99

CO

NTA

INM

ENT

LPSI

HEA

DER

TO

LO

OP

2B

ZON

E 88

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

74

SI-1

74

12”

X 1

.125

12”

X 1

.312

79-2

3

79-2

7

79-2

5

79-4

7

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-136

18

SI-1

74H

-12

V-5

41

ZON

E 26

SI-1

74H

-11

SI-1

74H

-5

SI-1

74H

-4

SI-1

74H

-13

SI-1

74H

-10

SI-1

74H

-8W

79-2

3

79-2

5

79-4

1

79-2

7

79-3

5

79-3

4

79-3

6

79-3

7

79-4

2

79-3

8 79-3

9

79-4

0

79-4

4

79-4

3

79-4

5

79-4

6

79-4

7

V-1

24

EL 9

3’-5

SI-E

-174

-CC

BA

-12”

ZON

E 11

5

79-7

0

79-3

7A

79-5

479

-55

W

B

B

B

B

C

B

C

W

187

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 188: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 10

0

CO

NTA

INM

ENT

LPSI

TR

AIN

A S

UC

TIO

N

ZON

E

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

07

SI-2

41

24”

X 0

.375

16”

X 0

.312

84-2

70-1

16

84-3

70-1

19

27

UV

-673

SI-2

41H

-19

84-5

W

84-3

SI-A

-007

-HC

BA

-24”

23

SI-3

69H

-1

W

84-2

70-1

34

70-1

32

70-1

31

70-1

28

70-1

22

70-1

29

70-1

26

70-1

25

70-1

17

70-1

23

70-1

19

70-1

20

70-1

21

V-6

53

PSV

-179

70-1

16

92

ZON

E93

SI-A

-241

-GC

BC

-16”

SI-A

-369

-GC

BC

-10”

SI-2

4116

” X

1.5

94”

70-1

2070

-121

SI-3

6910

” X

0.2

50”

70-1

2270

-132

SI-3

696”

X 0

.280

”70

-134

-

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-105

03-P

-SIF

-151

13

-P-Z

CG

-112

ZON

E 21

BC

B

03-P

-SIF

-201

188

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 189: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 10

1

CO

NTA

INM

ENT

LPSI

TR

AIN

B S

UC

TIO

N

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

30

SI-1

94

24”

X 0

.375

16”

X 0

.312

85-2

71-1

12

85-3

71-1

21

26

UV

-675

SI-1

94H

-22

85-5

W

85-3

SI-B

-030

-HC

BA

-24”

24

PSV

-189

ZON

E90

SI-B

-194

-GC

BC

-16”

SI-B

-368

-GC

BC

-10”

SI-1

9416

” X

1.5

94”

71-1

2271

-123

SI-3

6810

” X

0.2

50”

70-1

2471

-143

SI-3

686”

X 0

.280

”71

-145

-

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-105

03-P

-SIF

-151

13

-P-Z

CG

-112

ZON

E89

SI-1

94H

-16

SI-1

94H

-26

SI-3

68H

-2

71-1

12

71-1

23

71-1

24

71-1

21 71-1

19

71-1

25

71-1

18

71-1

2771

-148

71-1

36

71-1

22

71-1

16

71-1

15

71-1

49

71-1

13

71-1

51

71-1

31

71-1

37

71-1

30

71-1

33

71-1

34 71-1

40

71-1

39

71-1

42

71-1

43

71-1

45

ZON

E22 U

V-6

5485

-2

W

W

B

B

B

C

B

189

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 190: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

LIN

E#

DIA

/SC

HFR

OM

TO

SI-3

0724

" x 0

.562

"84

-12

84-3

7

SI-3

0720

" x 0

.375

"84

-39

84-4

6

SI-0

0918

" x 0

.312

"80

-14

84-8

7

SI-0

0810

" x 0

.250

"84

-51

84-8

4

RE

FER

EN

CE

DW

G'S

03-

P-S

IF-2

01

ZON

E 9

3W

ES

T W

RA

P84

-12

V-20

5EL

72'

84-1

4

84-1

6

H2

SI-A

-307

-GC

BC

-24"

84-1

8

84-2

0

84-2

2

84-2

684-2

484

-51

84-2

8

84-2

9

84-3

1

84-5

3

SI-A

-008

-GC

BC

-10"

84-5

5

84-5

784

-59

84-6

3

84-6

5

84-6

784

-69

84-7

1

84-7

2

V-47

0

84-7

4

84-7

5

84-7

7

84-7

984-8

084-8

2

84-8

4

HPS

IP

UM

P #

1

84-3

3

84-8

784-8

6

SI-A

-009

-GC

BC

-18"

84-3

5

84-3

784

-39

84-5

0

V-10

580

-15

80-1

4

V-15

7

ZON

E 76

CSP

SU

CTI

ON

SI-A

-307

-GC

BC

-20"

84-8

5

84-8

9

84-4

1

84-4

3HV-

683

84-4

484-4

6

V-20

1

ZON

E 7

0LP

SI "

A"S

UC

TIO

N

CO

NT.

ON

CO

NT.

ON

CO

NT.

ON

SI-3

07W

84-3

4 CO

NT.

ON

ZON

E 10

3R

WT

SU

CTI

ON

H6

SI-3

07

H7

H8

H10

SI-3

07

H1

H2

H5

H4H

3

H1 H

5

SI-0

08

SI-0

08

SI-0

08

SI-0

08

SI-0

09

SI-0

09

SI-0

09

SI-3

07

SI-3

07

84-4

8

H15

SI-3

07W

H3

SI-3

07W

H5

SI-3

07

ZON

E 1

16

ZON

E 10

2

SA

FETY

INJE

CTI

ON

PU

MPS

A

TR

AIN

SU

CTI

ON

84-9

3

84-9

184

-88

84-9

0

84-9

2

W

W

W

W

W

W

W

WW

B

B

B

B

B

BB

B

B

B

B

BC

B

B

190

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 191: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

86-2

0

86-1

486

-12

86-1

886

-16

25

86-2

7

86-2

9

86-3

1

V-30

6

86-5

86- 86-2

3

CH

-A-1

42-H

CB

A-2

0"86

-33

86-1

86-3

5

86

86-1

0

886

-

86-7

86-3

86-5

SI P

UM

P SU

CT.

CH

-A-4

24-G

CB

C-2

0"

HV

531

ZON

E 10

2

REF

UEL

ING

WAT

ERTA

NK

86-5

9 86-5

7

CH

-A-1

42-H

CB

A-2

0"

86-5

186

-49

86-4

786-6

286-4

5

86-4

3

86-4

1

86-6

0

86-5

5

86-5

3

86-3

7

ESSE

NTI

AL

PIPE

TU

NN

EL88

'A

UX

BLD

G

86-3

9

LIN

E#D

IA/S

CH

FRO

MTO

CH

- 424

20"

x 0.

375"

86-1

86-2

0

CH

- 142

20"

x 0.

375"

86-2

186

-59

Ref

eren

ce D

WG

'S.

03-P

-SIF

-201

03-P

-ZYA

-925

- 21

CO

NT

ON

88' P

IPE

CH

ASE

H20

CH

-142

70’

El.

51’ 6

"

H14

CH

-142

H22

CH

-142

H13

CH

-142

H2

CH

-424

H3

CH

-424

H6

CH

-424

H8

CH

-142

H1

CH

-424

H4

CH

-142

H1

CH

-142

H6

CH

-142

H3

CH

-142

H2

CH

-142

W

W

ZON

E 10

3

REF

UEL

ING

WA

TER

SU

CTI

ON

A

TR

AIN

86-6

4 86-6

6

W

W

W

W

H6

CH

-142

W

WW

B

B

B

B

B

B

B

B

B

B

B

B

B

B

191

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 192: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

LIN

E#

DIA

/SC

HFR

OM

TO

SI-3

0824

" x 0

.562

"85

-12

85-3

7

SI-3

0820

" x 0

.375

"85

-38

85-4

9

SI-3

318

" x 0

.312

"85

-50

81-1

3

SI-3

110

" x 0

.250

"85

-59

85-8

0

CH

-150

3" x

0.2

16"

104-

210

4-5

RE

FER

EN

CE

DW

G'S

03-P

-SIF

-202

85-1

8

85-2

0

85-2

2

85-2

4

85-2

685

-28

85-5

9

85-6

1

85-6

9

85-6

3

85-6

5

85-6

7

85-7

185

-72

V-40

2

85-7

4 85-7

5

85-7

7

85-7

8

SI-B

-031

-GC

BC

-10"

85-8

0

85-2

985

-31

85-3

8

85-3

7

85-5

0

SI-B

-033

-GC

BC

-18" V-

158

81-1

4V-10

4

81-1

3

85-5

8

85-5

685-5

4

85-5

2

ZON

E 7

9C

ON

T. S

PR

AYP

UM

P "B

" SU

CT.

V-20

085-4

985

-47

85-4

6

HV-

692

85-4

485-4

2

SI-B

-308

-GC

BC

-20"

SI-B

-308

-GC

BC

-24"

85-4

0

85-3

385

-34

85-3

6ZO

NE

105

RW

T S

UC

T.

HP

SI P

UM

P #

2

LPS

I PU

MP

"B" S

UC

T.

W

H3

H1

H4

CO

NT.

ON

CO

NT.

ON

ZON

E 7

3

CO

NT.

ON

H3

H15

SI-3

08

H1

H4

H2

H11

H5

H8

H9

H5

SI-3

08

SI-3

08

SI-3

08SI

-308

SI-3

08

SI-3

1

SI-3

1

SI-3

1

SI-0

33

SI-3

08SI-3

08

SI-3

08

ZON

E 1

17

ZON

E 10

4

SA

FETY

INJE

CTI

ON

PU

MPS

B

TR

AIN

SU

CTI

ON

85-8

2

ZON

E 9

0E

AST

WR

AP

85-1

2 85-1

4

V-20

6T.

O.G

. EL.

70'

6"

CO

NT.

ON

V-32

7

104-

4

104-

5

104-

3

CH

-B-1

50-G

CB

C-3

104-

210

4-1

85-1

6

03-P

-CH

F-20

6

W

W

W

W

W

W

W

W

W

B B

B

B

B

B

B

B

C

B

B

B

B

192

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 193: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

87-7

5

CH

-B-1

49-H

CB

A-2

0"

LIN

E#

DIA

/SC

HFR

OM

TO

CH

-425

20" x

0.3

75"

87-1

87-1

8

CH

-149

20" x

0.3

75"

87-1

987

-75

87-7

3

87-7

1

87-6

987

-67

87-6

587-6

3

87-6

1

87-5

9

87-5

787-5

5

87-5

3

87-5

1

87-4

9

87-8

8

87-4

7

87-8

6

87-4

5

87-8

4

87-4

387

-82

87-4

1

87-8

0

87-3

9

87-7

8

87-3

7

87-3

5

87-3

3

87-3

1

87-2

9

EL.

88'

70'

87-2

7

CH

-B-1

49-H

CB

A-2

0"87

-25

87-2

3 87-2

187

-76

87-1

9

HV

530

87-1

8

87-1

4

87-1

6

EL

51'6

"87

-12

CH

-B-4

25-G

CB

C-2

0"87-1

0

87-8

V-30

5

87-7

87-5

87-3

87-1

ZON

E 1

04

SI-P

UM

PS

UC

TIO

NAU

X. B

LDG

.88

'E

SS

EN

TIA

LP

IPE

TU

NN

EL

RE

FUE

LIN

GW

ATER

TA

NK

CO

NT.

ON

Ref

eren

ce D

WG

'S.

03-P

-SIF

-202

03-P

-ZYA

-925

W

W

W

H21

CH

-149

H13

CH

-149

H10

CH

-149

H12

CH

-149

H27

CH

-149

H25

CH

-149

H26

CH

-149

H2

CH

-149

H6

CH

-149

H7

CH

-149

H4

CH

-149

H5

CH

-149

H8

CH

-149

H14

CH

-149

H3

CH

-149

H1

CH

-149

H1

CH

-425

H6

CH

-425

H9

CH

-149

ZON

E 10

5

REF

UEL

ING

WA

TER

SU

CTI

ON

B

TR

AIN

87-9

0

W

W

W

W

W

WW

W

W

W

W

W

B

BB

B

B

B B

B

B

B

B

B

BB

BB

B

B

B

193

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 194: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

99SI

-100

SI-1

00

4” X

0.3

37”

4” X

0.4

38”

4” X

0.4

38”

106-

110

6-8

106-

24

106-

710

6-44

106-

28

HV

-604

SI-A

-100

-CC

BA

-4”

SI-1

05H

-B

SI-1

00H

-2

SI-9

9H

-1

SI-1

00H

-9

SI-1

00H

-10

SI-1

00H

-1

SI-1

00H

-8

SI-1

00H

-6

SI-1

00H

-5

SI-1

05H

-D

SI-1

05H

-C

SI-1

00H

-3 SI-1

06H

-1

SI-9

9H

-2

106-

68

106-

69

106-

17

106-

44

106-

65

106-

72

106-

6

106-

24

106-

20

106-

4

106-

70

106-

71106-

66

106-

49

106-

18

106-

25

106-

59

106-

32

106-

29

106-

1

106-

33

106-

21

106-

50

106-

30

106-

67

106-

12

106-

7

106-

42

106-

40

106-

51

106-

10

106-

23

106-

48

106-

22

106-

8

106-

41

106-

9

106-

16

106-

31

106-

38

106-

36

106-

47

106-

35

106-

3

106-

39

106-

2

106-

5

106-

4610

6-19

106-

45

106-

27

106-

43

106-

61

106-

37

106-

60

106-

62

ZON

E 10

8

SI-A

-105

-CC

BB

-2”

SI-A

-106

-CC

BA

-3”

V42

4

V-4

04

V-2

18

UV

-666

03-P

-SIF

-203

SI-1

00H

-15 SI-1

00H

-7

106-

14

106-

13

106-

15

106-

11

V-4

76

HV

-698

106-

54

106-

52

106-

56

106-

57

106-

58

106-

63

106-

55

106-

5310

6-64

A

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

POIN

T A

CO

NTI

NU

EDTH

IS D

RA

WIN

G

SI-1

00H

-34

106-

26

EL 4

1’-2

EL 4

6’-3

EL 4

1’-2

EL 4

8’-1

0”SI

-A-1

05-C

CB

B-2

SI-A

-100

-CC

BA

-4”

SI-1

00H

-11

SI-A

-99-

CC

BB

-4”

SI-1

052”

X 0

.344

”10

6-49

106-

72EL

88’

SI-1

052”

X 0

.344

”10

6-63

106-

68SI

-106

3” X

0.4

38”

106-

4510

6-48

ZON

E 10

6

HPS

I PU

MP

RO

OM

“A

DIS

CH

AR

GE

HPS

I APU

MP

106-

34

EL 5

1’-6

106-

28SI

-100

H-4

SI-1

00H

-16

SI-1

00H

-36

SW

SW

ZON

E 11

8

W

W

W

W

W

W W

W

W

W

W

W

W

W

W

W

W

WW

SI-1

05H

-JW

B

AB

B

B

BB

B

C

B

B

B

B

CB

B

C

B

B

B

B

B

ZON

E 11

6

SI-A

-100

-CC

BA

-4”

194

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 195: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 10

7

HPS

I PU

MP

RO

OM

“B

DIS

CH

AR

GE

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

07SI

-107

SI-1

07

4” X

0.3

37”

4” X

0.3

37”

3” X

0.4

38”

107-

110

7-23

107-

68

107-

4110

7-27

107-

71

SI-1

07H

-8

SI-1

07H

-5

SI-1

07H

-46

SI-1

07H

-3

SI-1

07H

-48

SI-1

07H

-12

SI-1

07H

-2

107-

15

107-

11

107-

41

107-

8

107-

45

107-

38

107-

37

107-

35

107-

24

107-

44

107-

71

107-

3

107-

6

107-

1

107-

26

107-

33

107-

36

107-

25

107-

34

107-

2

107-

14

107-

39

107-

31

107-

16

107-

23

107-

4

107-

5 107-

42

107-

47

107-

46

ZON

E 10

9

SI-B

-107

-CC

BB

-4”

SI-B

-107

-CC

BB

-4”

V40

5

HV

-609

HV

-699

03-P

-SIF

-204

SI-1

07H

-4

107-

12

107-

40

107-

32

107-

7

107-

10

107-

43

107-

21

107-

9

POIN

T A

CO

NTI

NU

EDTH

IS D

RA

WIN

G

EL 4

7’-3

EL 4

1’-2

EL 4

6’-9

SI-B

-107

-CC

BB

-3”

SI-B

-112

-CC

BA

-2”H

PSI B

PUM

P

SI-1

122”

X 0

.344

”10

7-42

107-

65SI

-112

2” X

0.3

44”

107-

5610

7-60

SI-1

122”

X 0

.344

”10

7-66

107-

67

DIS

CH

AR

GE

SI-1

07H

-11

SI-1

07H

-7SI

-107

H-6

SI-1

07H

-9

SI-1

07H

-10

V-4

78

107-

28

107-

20

107-

18

107-

1910

7-17

107-

69

107-

70107-

48

107-

1310

7-30

107-

29

107-

22

107-

27

107-

68

SI-1

12H

-H

SI-1

12H

-G

SI-1

12H

-C

107-

57

107-

63

107-

6110

7-62

107-

58

107-

5210

7-59

107-

54

107-

53

107-

55

SI-B

-112

-CC

BB

-2”

V42

6

V-2

19

UV

667

107-

64

107-

67

107-

49

107-

50

107-

51

107-

56

107-

65

107-

66

107-

60

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

EL 4

1’-2

V40

0

A

EL 4

4’

SI-1

07H

-1

EL 4

6’-3

EL 4

8’-1

0”

EL 5

1’-6

SW

SW

ZON

E 11

9

W

W

WW

W

W

W

W

W

W

W

W

W

B

B

C

B

B

C

B

B

A

B

B

C

BB

B

B

B

ZON

E 11

7

195

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 196: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 10

8

HPS

I DIS

CH

AR

GE

88’ P

IPE

CH

ASE

REF

EREN

CE

DR

AWIN

GS

SI-A

-100

-CC

BA

-4”

03-P

-SIF

-203

SI-1

00H

-18

108-

7

03-P

-SIF

-204

03-P

-CH

F-20

7

EL. 8

9’ 4

SI-1

00H

-21

SI-1

00H

-26

SI-1

00H

-29

SI-1

00H

-13

SI-1

00H

-12

SI-1

00H

-19

SI-1

00H

-32

SI-1

00H

-35 SI-1

00H

-31

SI-1

18H

-S

SI-1

18H

-R

SI-1

18H

-P

SI-1

18H

-N

SI-1

18H

-H

SI-1

18H

-E

SI-1

18H

-A

108-

17

108-

8

108-

16

108-

13

108-

12

108-

9

108-

11

108-

2

108-

18

108-

4

108-

14

108-

5

108-

19

108-

6

108-

15

108-

27

108-

26

108-

33

108-

31

108-

25

108-

39

108-

22

108-

40

108-

41

108-

38

108-

32

108-

28

108-

29

108-

37

108-

34

108-

36

108-

2410

8-23

108-

2010

8-21

108-

30

108-

43

108-

44

108-

42

108-

45

SI-A

-100

-CC

BB

-4”

SI-E

-118

-CC

BA

-2”

EL. 8

9’

EL. 9

2’2”

EL. 9

2’

EL. 9

2’

EL. 9

3’ 1

0”

V50

8

ZON

E 11

2

ZON

E 10

6

CH

AR

GIN

GPU

MP

A

ZON

E 11

1

108-

3

108-

1

108-

10

SI-1

00H

-20

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

00

SI-1

18

4” X

0.4

38”

2” X

0.3

44”

108-

1

108-

35

108-

34

108-

45

100’

W

W

W

W

W

W

W

W

W

W

W

W

W

W

108-

35

B

BC

B

B

C

B

B

BBB

B

B

B

B

B

B

B

196

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 197: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 10

9

HPS

I DIS

CH

AR

GE

88’ P

IPE

CH

ASE

REF

EREN

CE

DR

AWIN

GS

SI-B

-107

-CC

BB

-4”

03-P

-SIF

-203

SI-1

07H

-25

SI-1

07H

-26

SI-1

07H

-35

SI-1

07H

-21

SI-1

07H

-20

SI-1

07H

-14

SI-1

07H

-13

SI-1

07H

-47

SI-1

07H

-16

SI-1

07H

-19

SI-1

07H

-15

SI-1

07H

-34

SI-1

07H

-37

SI-1

07H

-3610

9-37

109-

35

109-

34

109-

36

109-

33 109-

32

109-

31

109-

30

109-

9

109-

8

109-

5

109-

6

109-

4

109-

7

109-

310

9-110

9-2

109-

29

109-

26

109-

28

109-

24

109-

27109-

25

109-

2310

9-22

109-

20

109-

21

109-

16

109-

14

109-

19

109-

15

109-

18

109-

13

108-

17

109-

12

109-

11

109-

10

109-

40

109-

41

109-

42

109-

43

03-P

-SIF

-204

SI-B

-107

-CC

BB

-4”

EL. 8

8’ 6

EL. 5

1’ 8

FRO

MH

PSI B

40’

EL. 8

9’ 4

EL. 9

1’

EL. 8

9’ 4

EL. 9

2’ 2

”ZO

NE

110

ZON

E 10

7

ZON

E 11

3EL

. 93’

10”

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

074”

X 0

.337

”10

9-1

109-

43

WW

W

W

W

W

W

W

W

B

B

C

B

B

C

B B

C

B B

B

B

B

197

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 198: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

REF

EREN

CE

DR

AWIN

GS

SI-B

-107

-CC

BB

-4”

03-P

-SIF

-203

110-

24

EL. 8

8’ 6

ZON

E 10

9

SI-2

36H

-B

SI-1

07H

-A

SI-2

18H

-1

SI-2

18H

-3

SI-2

18H

-2SI

-218

H-B

SI-1

10H

-ASI

-107

H-4

2

SI-1

07H

-45

SI-1

07H

-41

SI-1

07H

-39

SI-1

03H

-D

SI-1

03H

-BSI

-103

H-E

110-

1511

0-29

110-

3011

0-31

110-

22

110-

28

110-

17

110-

21

110-

25

110-

12

110-

16

110-

23

110-

19

110-

10

110-

14

110-

20

110-

18

110-

5

110-

9110-

13

110-

11

110-

3

110-

8110-

53

110-

7

110-

1

110-

4

110-

6

110-

2

110-

3511

0-3611

0-37

110-

39

110-

32

110-

34

110-

38

110-

33

110-

57 110-

56

110-

6011

0-62

110-

59

110-

58

110-

61

110-

63

110-

47

110-

45

110-

46

110-

50

110-

49110-

48

110-

64

110-

5111

0-42

110-

41

110-

40

110-

44

110-

43

UV

636

UV

646

UV

637

ZON

E 11

1

ZON

E 11

4

ZON

E 11

1

15

EL. 8

5’

EL. 9

3’ 5

EL. 8

6’ 6

EL. 8

8’ 6

EL. 8

5’ 9

/16”

SI-1

07H

-44

SI-1

07H

-43

SI-E

-218

-CC

BA

-2”

SI-E

-218

-CC

BA

-4”

SI-B

-110

-CC

BB

-2”

SI-E

-218

-CC

BA

-3”

SI-A

-103

-CC

BA

-2”

SI-E

-236

-CC

BA

-2”

SI-B

-107

-CC

BB

-2”

SI-1

03H

-A11

0-55

110-

5411

0-52

ZON

E 11

0

HPS

I DIS

CH

AR

GE

WES

T W

RA

P

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

032”

X 0

.344

”11

0-40

110-

52

SI-1

074”

X 0

.337

”11

0-1

110-

10SI

-110

2” X

0.3

44”

110-

1111

0-17

SI-2

182”

X 0

.344

”11

0-18

110-

22SI

-218

3” X

0.4

38”

110-

3811

0-39

SI-1

072”

X 0

.344

”11

0-53

110-

59

SI-2

184”

X 0

.438

”11

0-23

110-

37SI

-236

2” X

0.3

44”

110-

6011

0-64

110-

65

W

W

W

W

W

W

B

B C

B

B

B

B

C

B

B

B

B

B

C

B

BC

198

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 199: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-203

SI-1

00H

-37

111-

29U

V64

7

16

EL. 8

5’

SI-A

-100

-CC

BA

-4”

ZON

E 11

0

ZON

E 11

0

111-

30

111-

33

111-

31

111-

34

111-

37

111-

32

111-

35

111-

38

111-

36

111-

3911

1-40

111-

22

111-

28

111-

2611

1-27

111-

25

111-

24

111-

17

111-

18

111-

2011

1-19

111-

21

111-

23

111-

811

1-12

111-

15

111-

13

111-

16 111-

14

111-

11

111-

511

1-6

111-

9

111-

7

111-

1011

1-411

1-2

111-

1

111-

3

SI-1

00H

-B

SI-2

36H

-2

SI-2

36H

-3

SI-1

00H

-30

SI-1

00H

-A

SI-A

-100

-CC

BA

-2”

SI-E

-236

-CC

BA

-4”

SI-E

-236

-CC

BA

-3”

EL. 8

8’ 6

EL. 8

5’

EL. 9

3’ 5

ZON

E 10

8

111-

41

ZON

E 11

1

HPS

I DIS

CH

AR

GE

WES

T W

RA

P

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

002”

X 0

.344

”11

1-9

111-

25

SI-2

363”

X 0

.438

”11

1-40

111-

41SI

-236

4” X

0.4

38”

111-

2611

1-39

SI-1

004”

X 0

.438

”11

1-1

111-

8ZO

NE

114

W

W

BB

B

B

B

C

199

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 200: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

SI-1

76H

-2

SI-1

01H

-A

SI-1

76H

-3

112-

3

112-

25

112-

8

112-

42

112-

46

112-

45

112-

35

112-

44

SI-1

76H

-1112-

43

SI-1

02H

-BSI

-102

H-A

SI-1

00H

-17

SI-1

01H

-D11

2-17 11

2-21

112-

26

SI-A

-100

-CC

BA

-4”

14

112-

40

112-

18

112-

38

112-

39

112-

32

112-

41

112-

30

112-

33

112-

31

112-

37

112-

2911

2-36

112-

2411

2-34

112-

20

112-

28

UV

-617

112-

4

112-

12

112-

9

112-

23

112-

5

112-

14

112-

16

112-

27

112-

6

112-

13

112-

7

112-

2

112-

1

112-

15

112-

22

112-

10

112-

11

SI-E

-176

-CC

BA

-3”

SI-E

-176

-CC

BA

-4”

SI-A

-101

-CC

BA

-2”

ZON

E 10

8

ZON

E 11

5

SI-A

-102

-CC

BA

-2”

SI-1

01H

-B

112-

19

UV

-627

ZON

E 11

3

ZON

E 11

3

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

00SI

-101

SI-1

02

4” X

0.4

38”

2” X

0.3

44”

2” X

0.3

44”

112-

111

2-7

112-

21

112-

611

2-20

112-

32SI

-176

4” X

0.4

38”

112-

3311

2-44

SI-1

763”

X 0

.438

”11

2-45

112-

46

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-204

ZON

E 11

2

HPS

I DIS

CH

AR

GE

EA

ST W

RA

P

EL 8

8’-9

EL 9

2”-6

EL 9

3’-5

SI-1

01H

-C

WW

W

W

B

B

B

B

B

BB

B

B

B

200

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 201: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

SI-1

07H

-22

SI-1

09H

-A

SI-1

57H

-4

SI-1

57H

-6

SI-1

07H

-24

113-

38

113-

37

113-

51

113-

7

113-

2

113-

1

113-

41

113-

49

SI-1

76H

-A

APOIN

T A

CO

NTI

NU

EDTH

IS D

RA

WIN

G

SI-1

08H

-A

SI-1

57H

-5

113-

3

SI-B

-107

-CC

BB

-4”

13

113-

30

113-

31

113-

20

UV

-626

113-

9

113-

3611

3-43

113-

39

113-

25

113-

42

113-

28

113-

14

113-

12

113-

11

113-

10

113-

17

113-

18

113-

16

113-

1311

3-19

113-

8

113-

15

113-

4

113-

21

113-

2311

3-26 11

3-6

113-

22

113-

5

113-

24

113-

40

113-

27

113-

35 113-

33

113-

34

113-

48

113-

47

113-

45

113-

44

UV

-616

SI-1

57H

-9

SI-E

-157

-CC

BA

-4”

SI-E

-157

-CC

BA

-4”

SI-B

-108

-CC

BB

-2”

SI-B

-109

-CC

BB

-2”

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

ZON

E 10

9

ZON

E 11

5

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

03-P

-SIF

-204

SI-1

082”

X 0

.344

”11

3-7

113-

15

SI-1

092”

X 0

.344

”11

3-21

113-

27SI

-157

4” X

0.4

38”

113-

3311

3-49

SI-1

573”

X 0

.438

”11

3-50

113-

51SI

-157

2” X

0.3

44”

113-

1611

3-20

SI-1

57H

-A

SI-1

57H

-1

SI-1

074”

X 0

.337

”11

3-1

113-

6

113-

50

ZON

E 11

2

ZON

E 11

2

113-

29

ZON

E 11

3

HPS

I DIS

CH

AR

GE

EA

ST W

RA

P

SI-E

-176

-CC

BA

-2”

SI-E

-157

-CC

BA

-2”

EL 8

6’

EL 9

2’-6

EL 8

8’-9

EL 8

4’-6

113-

46

113-

32

SI-1

762”

X 0

.344

”11

3-28

113-

32

W

113-

53

113-

52

W

W

WBB

B

B

B

B

C

B

B

B

B

SI-E

-157

-CC

BA

-3”

201

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 202: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 11

4

CO

NTA

INM

ENT

H

PSI H

EAD

ER L

OO

P 1A

& 1

B

SI-2

18H

5

SI-2

36H

-5

114-

16

114-

9

15

16

114-

20

114-

5

114-

7

114-

11

114-

1114-

3

114-

4

114-

2

114-

21

114-

1911

4-8

114-

1711

4-6

114-

1511

4-22

114-

18

SI-E

-218

-CC

BA

-3”

SI-E

-236

-CC

BA

-3”

ZON

E 97

ZON

E 11

1

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-2

18

SI-2

36

3” X

0.4

38”

3” X

0.4

38”

114-

1

114-

12

114-

11

114-

23

03-P

-SIF

-103

ZON

E 96

EL 9

1’-4

V-1

33

EL 9

3’-5

114-

12

114-

14

V-1

43

114-

2311

4-13

EL 9

3’-5

ZON

E 11

0

BB

202

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 203: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 11

5

CO

NTA

INM

ENT

H

PSI H

EAD

ER L

OO

P 2A

& 2

B

SI-1

57H

-11

115-

17

115-

2011

5-19

115-

7

115-

5

13

14

115-

8

115-

9

115-

6

115-

11

115-

12

115-

10

115-

1

115-

3

115-

14

115-

21

115-

15

115-

22

115-

16

115-

18

115-

2

115-

4

115-

13

SI-1

76H

-4

SI-E

-157

-CC

BA

-3”

SI-E

-176

-CC

BA

-3”

ZON

E 99

ZON

E 11

2

ZON

E 11

3

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

57

SI-1

76

3” X

0.4

38”

3” X

0.4

38”

115-

1

115-

13

115-

12

115-

22

03-P

-SIF

-136

ZON

E 98

EL 9

1’-4

EL 9

3’-5

V-1

13

V-1

23

EL 8

9’-9

EL 9

3’-5

B

B

203

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 204: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 11

6

HPS

I PU

MP

A

REF

EREN

CE

DR

AWIN

GS

03-P

-SIF

-201

1) T

AG

NU

MB

ER: 3

MSI

AP0

2

2) S

ERIA

L N

UM

BER

: IN

GER

SOL

RA

ND

DIS

CH

AR

GE

SUC

TIO

NZO

NE

102

ZON

E 10

6

116-

1D

W

116-

1A

W

116-

1CW

116-

1BWN

116-

111

6-2

S/N

077

6-19

03-P

-SIF

-203

3) D

ISC

HA

RG

E H

EAD

STU

DS

16@

2.2

5”

DIA

. X 1

0.88

DIS

CH

AR

GE

HEA

D S

TUD

S

B

B

B

B

204

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 205: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 11

7

HPS

I PU

MP

B

REF

EREN

CE

DR

AWIN

GS

DIS

CH

AR

GE

SUC

TIO

N

1) T

AG

NU

MB

ER: 3

MSI

BP0

2

2) S

ERIA

L N

UM

BER

: IN

GER

SOL

RA

ND

ZON

E 10

4ZO

NE

107

117-

1D

W

117-

1BW

117-

1A

W

117-

1CW

N

117-

111

7-2

S/N

077

6-18

3) D

ISC

HA

RG

E H

EAD

STU

DS

16@

2.2

5”

DIA

. X 1

0.88

DIS

CH

AR

GE

HEA

D S

TUD

S

03-P

-SIF

-201

03-P

-SIF

-203

B

B

B

B 205

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 206: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

REF

EREN

CE

DR

AWIN

GS

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

063”

X 0

.438

”11

8-1

118-

49

HV

-604

SI-1

06H

-18

SI-1

06H

-24

SI-1

06H

-3

SI-1

06H

-11

SI-1

06H

-10

SI-1

06H

-9

SI-1

06H

-7

SI-1

06H

-14

SI-1

06H

-15

SI-1

06H

-13

SI-1

06H

-16

118-

31

118-

48

118-

32

118-

34

118-

3

118-

36

118-

4

118-

20

118-

22

118-

25

118-

49

118-

5

118-

27

118-

43

118-

47

118-

14

118-

33

118-

26

118-

13

118-

28

118-

29

118-

19

118-

10

118-

8

118-

37

118-

711

8-1

118-

35

118-

2

118-

39

118-

38

118-

17

118-

15

118-

9

ZON

E 39

SI-A

-106

-CC

BA

-3”

03-P

-SIF

-203

SI-1

06H

-6 SI-1

06H

-8

118-

42

118-

45 V

-523

HV

-321

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

SI-1

06H

-23

118-

18

EL 4

6’-3

EL 8

5’

SI-1

06H

-12

EL 9

2’ 6

ZON

E 11

8

HPS

I “A

” LO

NG

TER

M

REC

IRC

ULA

TIO

N

118-

6

EL 5

1’-6

118-

21

SI-1

06H

-4SI

-106

H-5

SI-1

06H

-21

SI-1

06H

-22

SI-1

06H

-2

7711

8-44

SI-1

06H

-25

SI-1

06H

-20

SI-1

06H

-19

118-

41

118-

40

118-

46

APO

INT

AC

ON

TIN

UED

THIS

DR

AW

ING

118-

23

118-

16

118-

24

118-

1111

8-12

03-P

-SIF

-105

SI-A

-106

-CC

BA

-3”

ZON

E 10

6

SI-1

06H

-26

118-

30

W

W

W

W

W

W

W

W

WW

W

W

WW

W

W

W

W

B

B

B

B

BB

B

B

B

B

BB

B

B

B

B

B

B

C

B

B

B

C

B

206

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 207: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

14SI

-319

3” X

0.4

38”

2” X

0.3

44”

119-

111

9-53

119-

5211

9-57

ZON

E 11

9

HPS

I “B

” LO

NG

TER

M

REC

IRC

ULA

TIO

N

REF

EREN

CE

DR

AWIN

GS

SI-1

14H

-8

SI-1

14H

-4

SI-1

14H

-1

SI-1

14H

-10

SI-1

14H

-22

SI-1

14H

-9

SI-1

14H

-26

119-

54

119-

52

119-

14

119-

24

119-

49

119-

11

119-

10

119-

8

119-

23

119-

30

119-

2

119-

26

119-

32

119-

41

119-

57

119-

6

119-

9

119-

7

119-

47

119-

12

119-

4

119-

56

119-

55

119-

21

119-

53

119-

35

119-

15

119-

17

ZON

E 40

SI-E

-319

-CC

BA

-2”

SI-B

-114

-CC

BA

-3”

HV

331

HV

-609

V-5

09

03-P

-SIF

-105

SI-1

14H

-27

119-

43

119-

13

119-

5

119-

16

119-

19

119-

31

119-

20

119-

25

EL 4

6’-3

EL 8

7’-3

EL 4

6’-8

SI-B

-114

-CC

BA

-3”

SI-1

14H

-7

SI-1

14H

-3SI

-114

H-2

SI-1

14H

-5

SI-1

14H

-6

119-

3

119-

44

119-

33

119-

50

119-

18

119-

22

119-

42

119-

36

119-

1119-

34

119-

40

SI-B

-114

-CC

BA

-3”

V-5

3311

9-46

119-

51

119-

45

EL 8

7’-3

AEL

88’

SI-1

14H

-21

EL 8

5’-4

”EL

92’

-6”

EL 5

1’-6

SI-3

19H

-A

SI-3

19H

-G

67

A

ZON

E 10

7

119-

29119-

2811

9-27

SI-1

14H

-17

SI-1

14H

-15

SI-1

14H

-16

119-

37

119-

3811

9-39

03-P

-SIF

-204

03-P

-CH

F-20

7

SI-1

14H

-13

SI-1

14H

-12

SI-3

19H

-B

POIN

T A

CO

NTI

NU

EDTH

IS D

RA

WIN

G

POIN

T A

CO

NTI

NU

EDTH

IS D

RA

WIN

G

119-

48

W

W

W

W

W

W

W

WWW

W

WSI

-319

H-J

B

B

C

B

B

C

B

BC

B

B

B

B

B

BB

B

B

B

B

B

B

B

207

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 208: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 12

0

CO

NTA

INM

ENT

SPR

AY

A

CO

NT

ZON

E 93

LIN

E #

DIA

X S

CH

FRO

MTO

SI-0

8810

” X

0.2

50”

120-

112

0-19

REF

EREN

CE

DR

AWIN

GS

13-P

-ZC

G-1

05

21

SI-8

8H

-5

120-

9

120-

12

120-

6

120-

11

120-

10

120-

712

0-5

120-

8

120-

212

0-1

V-1

64

SI-A

-088

-GC

BC

-10”

120-

13

120-

4

120-

3

EL 1

16’-

4”

120-

14

120-

15

120-

16

120-

19

120-

1812

0-17

C

208

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 209: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

UN

IT 3

ZON

E 12

1

CO

NTA

INM

ENT

SPR

AY

B

CO

NT

ZON

E 90

LIN

E #

DIA

X S

CH

FRO

MTO

SI-1

3010

” X

0.2

50”

121-

112

1-21

REF

EREN

CE

DR

AWIN

GS

13-P

-ZC

G-1

05

22

SI-1

30H

-7 121-

13

121-

6

121-

14

121-

07121-

5

121-

18

V-1

65SI-B

-130

-GC

BC

-10”

121-

08

121-

4

121-

19

EL 1

16’-

4”

121-

15

121-

16

121-

17

121-

20

121-

21

121-

3 121-

1

121-

2

121-

912

1-11

121-

12

121-

10

C

209

of 2

123I

NT-

ISI-3

, Rev

. 3

Page 210: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SECTION 11.0 Terms and Definitions

210 of 212 3INT-ISI-3, Rev. 3

Page 211: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

AHE: Augmented High Energy ANII: Authorized Nuclear Inservice Inspector APS: Arizona Public Service Company, et al ASME: American Society of Mechanical Engineers Aux: Auxiliary BWR: Boiling Water Reactor CE: Combustion Engineering CEDM: Control Element Drive Mechanism CFR: Code of Federal Regulations CH: Charging CHR: Containment Heat Removal Circ: Circumferential CL: Cold Leg CRD: Control Rod Drive CS: Containment Spray CSP: Containment Spray Pump DWG: Drawing ECCS: Emergency Core Cooling System FW: Feedwater HL: Hot Leg HPSI: High Pressure Safety Injection HV: Hand Control Valve Hx: Heat Exchanger ICI: In Core Instrumentation IEB: Inspection and Enforcement Bulletin IEIN: Inspection and Enforcement Information Notice Inj: Injection INPO: Institute for Nuclear Power Operations ISI: Inservice Inspection LPSI: Low Pressure Safety Injection MSSS: Main Steam Support Structure NDE: Nondestructive Examination NRC: Nuclear Regulatory Commission PDV: Pressure Differential Valve PSV: Pressure Relief or Safety Valve PWR: Pressurized Water Reactor PVNGS: Palo Verde Nuclear Generating Station PZR: Pressurizer RC: Reactor Coolant RCP: Reactor Coolant Pump REV: Revision RHR: Reactor Residual Heat Removal Recirc: Recirculation RCS: Reactor Coolant System RPV: Reactor Pressure Vessel RVLMS: Reactor Vessel Level Monitoring System REM: Roentgen Equivalent Man SDCHX: Shutdown Cooling Heat Exchanger SD: Shutdown

211 of 212 3INT-ISI-3, Rev. 3

Page 212: 3rd Inspection Interval Inservice Inspection Program ... · 8. B9.11, Zone 21 - Changed 2nd period requirements from 4 to 0. Added 3rd period requirements from 0 to 3. This is done

SER: Significant Event Report SG: Steam Generator SI: Safety Injection SN: Serial Number T: Thickness Tech. Spec: Technical Specification UFSAR: Updated Final Safety Analysis Report USNRC: United States Nuclear Regulatory Commission UV: Multivariable Control Valve V: Valve

212 of 212 3INT-ISI-3, Rev. 3