3huirupdqfh :runzhdu
TRANSCRIPT
grange
CHEMICAL RESISTANCE GUIDE
This chart provides general guidelines, but it should be remembered that gloveresistance is affected by other factors such as temperature, contamination, of other matter, concentration of chemical products, coating thickness, immersiontime etc. Therefore we recommend a primary test be done if any gloves are tobe used in hazardous conditions.
Specific details for each glove should be requested, that will better specify thedata required for selection, such as breakthrough time, permeation etc.We recommend that only branded products be used for chemical applications.
PERFORMANCE KEY RATING EXCELLENT GOOD FAIR NOT RECOMMENDEDE G F NR
grange
grange
MECHANICAL RESISTANCE GUIDE
This chart provides general guidelines, but it should be remembered that physical properties vary due to factors such as finish, thickness, moisture, oil contents etc.
Therefore we recommend a primary test is done for these applications.
PERFORMANCE KEY RATING EXCELLENT GOOD FAIR POORE G F P
SUPPORTED UNSUPPORTED
grange
POOR
THERMAL RESISTANCE GUIDE
This chart provides very general guidelines, but it must be remembered that glove resistance is affected by other factors that will effect the glove such as ambient temperature, exposure time, moisture, quality of raw materials etc. Therefore, we recommend a primary test be done if any gloves are to be used in hazardous thermal conditions outside of this 8-70°C range.
Specific details for each glove should be requested, particularly if the user will work for any time outside the 8 - 70° Celsius range or if molten metals present sub-zero temperatures etc. are within the application as various factors will affect the user
We strongly recommend that only branded or marked gloves be used for thermal hazards.
PERFORMANCE KEY RATING EXCELLENT GOOD FAIR NOT RECOMMENDEDE G F NRPOORP
grange
GLOVE TYPE GUIDE“dipped or coated”
PERFORMANCE KEY RATING EXCELLENT GOOD FAIRE G F
SHOULDER 75 - 60 cmfull arm protection
ELBOW 30 - 50 cmhand, wrist and forearmprotection
WRIST 23 - 30 cmhand and wrist protection
POORP
HP6070i Chrome Leather Glove - Wrist Length ■ FEATURES
• 1.1 - 1.3mm substance• Sans/EN Standards (388)• Reinforced palm & Thumb• Size 10.5• Bovine Leather (Cow Split)
■ APPLICATIONS• Heat Application (Up to 100°)• Mining• Abrasion Resistant• Traction oily surfaces
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6070I
N/A
EN388
EN388-4143
10.5 (XL)
Grey
HP6113i
HP2001/40
Chrome Leather Glove - Elbow Length
■ FEATURES• 1.1 - 1.3mm substance• Sans/EN Standards (388)• Reinforced palm & Thumb• Size 10.5• Bovine Leather (Cow Split)
■ APPLICATIONS• Heat Application (Up to 100°)• Mining• Abrasion Resistant• Traction oily surfaces• Furnace
Chrome Leather Glove - Shoulder Length
■ FEATURES• 1.1 - 1.3mm substance• Sans/EN Standards (388)• Reinforced palm & Thumb• Size 10.5• Bovine Leather (Cow Split)
■ APPLICATIONS• Heat Application (Up to 100°)• Mining• Abrasion Resistant• Traction oily surfaces• Furnace
Yarn
Coating/Material Leather
N/A
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6113I
N/A
EN388
EN388-4143
10.5 (XL)
Grey
Yarn
Coating Material Leather
N/A
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP2001/40
N/A
EN388
EN388-4143
10.5 (XL)
Grey
Yarn
Coating Material Leather
N/A
Agricultural Construction Fabrication
grange
4143
4143
4143
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Agricultural Construction Fabrication
Agricultural Construction Fabrication
grange
HP6180Bi
HP6180i Green Lined Leather Glove - Wrist Length
■ FEATURES• Tanned chrome Leather (Suede)• Wrist length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6180I
N/A
EN388
EN388-4144
XL
Green
Yarn
Coating Material N/A
Leather
Construction Moulten MetalEngineering4144
Abrasion
PunctureTearCut
HP6183R Red Lined Leather Glove- Elbow Length
■ FEATURES• Tanned chrome Leather (Suede)• Elbow length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6183I
N/A
EN388
EN388-4144
XL
Red
Yarn
Coating Material N/A
Leather
4144
Abrasion
PunctureTearCut
Construction Moulten MetalEngineering
Blue Lined Leather Glove - Wrist Length
■ FEATURES• Tanned chrome Leather (Suede)• Wrist length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6180Bi
N/A
EN388
EN388-4144
XL
Blue
Yarn
Coating Material N/A
Leather
Construction Moulten MetalEngineering4144
Abrasion
PunctureTearCut
HP6183grange
HP6183Bi
HP6183i Green Lined Leather Glove- Elbow Length
■ FEATURES• Tanned chrome Leather (Suede)• Elbow length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6183I
N/A
EN388
EN388-4144
XL
Green
Yarn
Coating Material N/A
Leather
4144
Abrasion
PunctureTearCut
Construction Moulten MetalEngineering
Blue Lined Leather Glove- Elbow Length
■ FEATURES• Tanned chrome Leather (Suede)• Elbow length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6183Bi
N/A
EN388
EN388-4144
XL
Blue
Yarn
Coating Material N/A
Leather
4144
Abrasion
PunctureTearCut
Construction Moulten MetalEngineering
Orange Lined Leather Glove Superior Leather- Elbow Length
■ FEATURES• Tanned chrome Leather (Suede)• Elbow length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6183
N/A
EN388
EN388-4144
XL
Orange
Yarn
Coating Material N/A
Leather
4144
Abrasion
PunctureTearCut
Construction Moulten MetalEngineering
grangeHP6184i Green Lined Leather Glove - Shoulder Length
■ FEATURES• Tanned chrome Leather (Suede)• Shoulder length• Breathable cotton liner for heat dissipation• Welted seams for added protection• Lined for controlled heat transfer
■ APPLICATIONS• Welding• Heat Application (100°C)• Abrasion Resistand• Any thermal application• Hot or cold use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6184I
N/A
EN388
EN4144
XL
Green
Yarn
Coating Material N/A
Leather
4144 Construction Moulten MetalEngineering
Abrasion
PunctureTearCut
HP10208 Leather Reinforced Utility Glove (Cut Level 5) ■ FEATURES
• A cut resistant liner consisting of a blend of Chineema and leather gives this glove a Cut Level 5 Rating +.
• The sewn on leather palm adds durability, grip and puncture resistance.
• This feature optimizes the re-use of this glove in the workplace with PPE Recycling Programs.
■ APPLICATIONS• Cut Resistant (5)• Mining• Fabrication• High Abrasive Resistance• Heat Application (up to 180°)
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP10208
Palm
On request
EN388-4543
X-Large
Grey
Yarn
Coating Material Leather
Chineema
EngineeringAutomotive4543
Abrasion
PunctureTearCut
Agricultural
HP6140grange - Superior Brick Handlers Glove
■ FEATURES• Leather Glove - Rubber palm (tube)• Full grain leather (reversed) for added lifespan• 7cm cuff for added protection• Apron Palm • 3mm Rubber working surface• Tried and tested by all brick yards
■ APPLICATIONS• Brick Yard use• Abrasive Application• Mining Application
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6140
Apron palm & Thumb
N/A
N/A
XL
Brown/Black
Yarn
Working Surface Rubber
Leather
Mining ConstructionAgriculture4133
Abrasion
PunctureTearCut
HP6208i Red Heat Superior Glove - Elbow Length
■ FEATURES• Tanned Leather (1.2-1.5mm)• Keular Thread (Sewn)• Black brushed - Air vented liner• RNF fingers (Double Leather)• Apron Palm
■ APPLICATIONS• High heat application (up to 150°)• Welding• Foundry use• Hot or cold application
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6208I
N/A
EN388
EN388-4144
XL
Red
Yarn
Coating Material N/A
Leather
grange
HP6208GR Red Heat grange Glove - Elbow Length
■ FEATURES• Tanned chrome leather (1.1-1.3mm)• Superior Leather• Elbow Length• Cotton Lined• Welted Seams
■ APPLICATIONS• Welding• Heat Application (120°)• Foundry use• Grinding
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6208GR
N/A
EN388
EN388-4144
XL
Red
Yarn
Coating Material N/A
Leather
4144
4144
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
HP6202iRed Heat Superior Glove - Wrist Length
■ FEATURES• Tanned Leather (1.2-1.5mm)• Keular Thread (Sewn)• Black brushed - Air vented liner• RNF fingers (Double Leather)• Apron Palm
■ APPLICATIONS• High heat application (up to 150°)• Welding• Foundry use• Hot or cold application
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6202I
N/A
EN388
EN388-4144
XL
Red
Yarn
Coating Material N/A
Leather
4144
Abrasion
PunctureTearCut
Construction Moulten MetalFabrication
Construction Moulten MetalFabrication
Construction Moulten MetalFabrication
HP6540Li Leather VIP Glove - Keystone (NAPPA)
■ FEATURES• Soft pig grain Leather• Keystone Thumb• Elastic back• Shurred Cuff
■ APPLICATIONS• Welding• Handling• Drivers Glove• Maintenance
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6540LI
N/A
N/A
EN388-4143
M,L,XL
Tan
Yarn
Coating Material Leather
N/A
Engineering Fabrication Mining4143
Abrasion
PunctureTearCut
grange
HP6546iKeystone VIP Glove - Lined (Thermal) ■ FEATURES
• Fully Lined - Cotton• Full Grain Leather• Water Resistant Application• Elasticated Cuff
■ APPLICATIONS• Freezer/Heat Application• Construction• Fabrication• Abrasive Application• Winter Wear
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6546I
N/A
N/A
EN388-4143
XL
Tan
Yarn
Coating Material Leather
N/A
4143
Abrasion
PunctureTearCut
Engineering Fabrication Mining
HP5620C Abrasion Pro Cut 5 Crayfish Glove ■ FEATURES
• Cut resistant liner• Rubber (stuck on) palm & fingers• Bull nose finger tips• Reinforced fore finger & thumb
■ APPLICATIONS• Heavy abrasive application • Wet & dry use• Mining• Mechanical• Fabrication
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5620C
Palm/Fingers
EN388
EN388-4544
9 - L
White/Black
Yarn
Coating Material Rubber
PVA/Anticut
4544
Abrasion
PunctureTearCut
Engineering Fabrication Mining
HP5652Super Handler - Nitrile Foam Glove - Palm Dipped
■ FEATURES• 13 Gauge liner for breathability• Open back for added flexability• Foam finish for added traction• Dexterity - Level 3• All sizes
■ APPLICATIONS• Mechanical• Automotive assembly• Electrical assembly - (Dexterous)
Item No.
Gauge
Coating
SABS
EN Rating
SizeHP5652
Nitrile Palm & Fingers
EN388
EN388-4121
S, M, L, XL, XXL
13 Gauge
Yarn Material Polyester
grange4121
Abrasion
PunctureTearCut
Colour Grey/White
HP5650 Yellow Nitrile Knit Wrist Glove ■ FEATURES
• New to the grange range• Yellow Nitrile/Cotton Liner• Good Chemical composite• Knit wrist 3/4 Dipped• High abrasive resistance• All sizes
■ APPLICATIONS• Abrasive Application• Semi wet application• Chemical application• General purpose use• Builders (Cost Saving)
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5650
3/4 Dipped
EN388
EN388-4111
S,M,L,XL
Yellow
Yarn
Coating Material Nitrile
Cotton
4111
Abrasion
PunctureTearCut
Agricultural Construction Engineering
Engineering Fabrication Mining
HP5653 Super Gripper - Latex Handler Glove
■ FEATURES• Super grip on non-oiled material• High abrasion resistance• Seamless liner for dexterity & comfort
■ APPLICATIONS• Glass Handling• Abrasive application• Scaffolding erection• Mining• Pattern making - Wood work
Item No.
Gauge
Coating
SABS
EN Rating
SizeHP5653
Latex/Rough Palm and fingers
EN388
EN388-21439 Gauge
Yarn Material Polycotton
S, M, L, XL, XXL
2143
Abrasion
PunctureTearCut
Colour Blue/Yellow
Agricultural Construction Fabrication
HP5654 Supa Feel - P/U Coated Glove ■ FEATURES
• Electrical pannel assembly• Switch Gear• Artisan/hand tool use• For use in any inspection application• Dextrous• All sizes
■ APPLICATIONS• Electrical - Assembly• Automotive - Finishing• Inspection Glove
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5654
Palm and fingers
EN388
EN388-2122
S, M, L, XL, XXL
Black
Yarn
Coating Material Polyurathane
Polyester
Automotive FabricationConstruction2122
Abrasion
PunctureTearCut
HP10214 Nitrile Cut Resistant Glove - Cut Level 5
■ FEATURES• Cut resistant - level 5• Nitrile coated palm (Abrasion resistant)• 70mm knitted cuff• PVA yarn (Abrasion and cut resistant)• Dexterity level high• Retail packaging
■ APPLICATIONS• Cut Resistant• Manufacturing• Blade handling• Metal handling• Any application where dexterity and cut
protection is required
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP10214
Palm & Fingers
EN
EN388-4543
S, M, L, XL, XXL
Grey
Yarn
Coating Material Nitrile
Chineema/PVA
Agricultural EngineeringAutomotive
grange
HP5655GPro-Grip Textured Nitrile/PU Miners Glove - Fully Coated ■ FEATURES
• Fully coated for ultimate protection against oil/ soiled materials
• Seamless liner designed for dexterity• Stretch Tex P/U for comfort• Breathable
■ APPLICATIONS• Mining• Mechanical• Use where “feel” is required• Fabrication
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5655G
Fully Coated
EN388
EN388-4121
S, M, L, XL, XXL
Black
Yarn
Coating Material Nitrile PU
Polyester/18G
4542
4121
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Agricultural Construction Fabrication
grange
HP10202 Nitrile Cut Resistant Glove - Cut Level 5 ■ FEATURES
• Cut resistant level 5• Nitrile coated palm• 50mm Elastic cuff• All sizes Avail• Seamless liner for dexterity
■ APPLICATIONS• Cut Resistant• Manufacturing• Blade handling• Metal handling
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP10202
Palm
EN388
EN388-4543
S, M, L, XL, XXL
Black/Grey
Yarn
Coating Material Nitrile
Chineema
4543
Abrasion
PunctureTearCut
EngineeringAutomotiveAgricultural
HP5513 Comarex Full Dip Glove - Elbow Length
■ FEATURES• Latex Coated Jersey Liner• Rough Hand (Crinkle Finish)• Smooth Cuff - 30cm• High abrasive coating• Jersey liner (A grade)
■ APPLICATIONS• Wet Handling• Thermal ( Cold Applications)• Light Chemical• Abrasive Application• Chemical (selected)
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5513
Fully Coated
N/A
EN388-4111
10 - XL
Yellow
Yarn Cotton
Agricultural MiningConstruction
Coating Material Latex
4111
Abrasion
PunctureTearCut
Comorex Knit Wrist Glove - Latex
■ FEATURES• Latex Coated/Jersey Liner• Elastic Cuff - Knitted• Rough Palm Latex Coating• Durable, washable, reusable• A Grade latex
■ APPLICATIONS• Construction• General Handling• Wet Handling Glove• Agriculture• Any Abrasive Application
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5524
Fully Coated
N/A
EN388-4111
10 - XL
Yellow
Yarn
Coating Material Latex
Cotton
4111
Abrasion
PunctureTearCut
Agricultural Construction Fabrication
HP5524
HPATG34874 MaxiFlex ■ FEATURES
• Ultra-lightweight, knitwrist, micro-foam nitrile coated glove.
• AirTech”1 technology delivers 360° breathability.• Optimized,Controlled grip through micro-cup finish.• Minimal palm thickness & thinner than most
comparable gloves.• Reducing hand fatigue and increasing comfort.
■ APPLICATIONS• Primary, secondary and final assembly.• Finishing and inspection, Gardening. • Handling of small components. • Maintenance. DIY. • Logistics and warehousing.• Using tools and instruments.
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHPATG34874
Palm
On request
EN388-4131
8,9,10
Black
HPATG34876
HPATG56426
MaxiFlex - Full Dip ■ FEATURES
• Ultra-lightweight, knitwrist, micro-foam nitrile coated glove.
• AirTech”1 technology delivers 360° breathability.• Optimized,Controlled grip through micro-cup finish.• Minimal palm thickness & thinner than most
comparable gloves.• Reducing hand fatigue and increasing comfort.
■ APPLICATIONS• Primary, secondary and final assembly.• Finishing and inspection, Gardening. • Handling of small components. • Maintenance. DIY. • Logistics and warehousing.• Using tools and instruments.
MaxiDry ■ FEATURES
• Ultra lightweight, synthetic latex coated glove.• General purpose assembly requiring precision
handling. • Superior grip in oily and wet environments.• Excellent dexterity due to strategic placement
of coating. Locking cuff prevents the glove from slipping;
• Elasticated wrist support provides snug fit.
■ APPLICATIONS• Gear box assembly. General handling. • Handling small castings. Handling of
small components. Light metal fabrication and parts handling.
• Primary, secondary and final assembly. • Shock absorber assembly. • Maintenance.• Submersible
Backing
Material Micto-foam nitrile
Cotton
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHPATG34876
Fully
On request
EN388-4131
8,9,10
Black
Yarn
Coating Material Micro-foam nitrile
Cotton
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHPATG56426
Palm
On request
EN388-4111
9,10
Purple/Black
Yarn
Coating Material Synthetic Latex
Cotton
Engineering AgriculturalMining
grange
4131
4131
4111
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Engineering AgriculturalMining
Engineering AgriculturalMining
HP8758 Hi-Viz Utility Glove - Wet and Dry
■ FEATURES• Ergonomically designed grange MINER glove with
synthetic palm pad that increases comfort & durability.• Expandable fourchettes and HI-VIZ fabric back
combine for personal fit and comfort.• Extra tacky fingertips enhance grip and provide longer
wear.• An adjustable wrist closure with a grange® nylon pull
tab.
■ APPLICATIONS• Heavy/light construction• Auto repair• Demolition• Manufacturing• Mining• Fabrication and landscaping.
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP8758
N/A
Not Tested
EN388-3232
M, L, XL
Grey/Orange
HP5659 Impact Resistant - Miners Glove (Cut Level 2)
■ FEATURES• Polyester/Chineema fiber that provides additional
strength and cut resistance. • The foam nitrile palm enhances grip and durability
and has a sewn in foam padding for impact resist-ance and ANTI-VIBRASION.
• Hand back is protected with TPR impact protective pad extending to the fingers for added protection.
• Excellent dexterity
■ APPLICATIONS• Mining• Anti Vibration• Any Abrasive Application• Material Handling• Wet & Dry use
Backing
Material Synthetic Leather
Spandex Hi-viz
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5659
Palm
On request
EN388-4222
M, L, XL
Black/Yellow
Yarn
Coating Material Micro-foam nitrile
Polyester/Chineema
grange
4222
3232
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
HP5666grange - Glove Meta Pro (Hi-viz)
■ FEATURES• Reinforced palm/ Slip resistance• Anti abrasion palm patches• Anti slip palm patches• Hi-viz & reflective back• TPR fingers for impact prevention• Reduced hand fatigue
■ APPLICATIONS• Mechanical• Mining• Fabrication• Oil & Gas industry
Item No.
Coating Range
SABS
EN Rating
SizeHP
Palm
EN388
EN388-4122
Mining FabricationEngineering
S, M, L, XL, XXL
4122
Abrasion
PunctureTearCut
Colour Black/Orange
Yarn
Coating Material High-viz
Spandex
Agricultural Construction Fabrication
Construction MiningFabrication Mining
grangeHPV5659 Impact Resistant Glove - Miners Cut Resistant (Level 5)
■ FEATURES• Cut level 5 (4544)• Nitrile Coated Palm• RNF Palm for abrasion resistance/ Anti vibration• Impact resistant fingers and back (TPR)• Velcro adjustable wrist• Padded
■ APPLICATIONS• Mining• Fabrication• High abrasives application• Wet and dry use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHPV5659
Palm
EN388
EN388-4544
S, M, L, XL, XXL
Blue/Black
Liner
Material Nitrile/TPR
Chineema
4544
Abrasion
PunctureTearCut
Construction MiningFabrication Mining
HP6663 Terry Towling Double Hand Glove ■ FEATURES
• Outer Glove: Terry Knit 24oz.• Inner glove: 7 Gauge tight weave 1000gpd.• Cuff: Cotton pasted (canvas) material.• 20cm cuff
■ APPLICATIONS• Abrasive Application• Hot & Cold Handling• Thermal application• General purpose use
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6663
N/A
EN388
EN388-3211
XL
Cream/Red
Backing
Material N/A
Cotton
Engineering Moulten MetalFabrication3211
Abrasion
PunctureTearCut
Cotton Crochet Glove - 600 GPD
■ FEATURES• Cotton blend• 600 grams per dozen• One size fits all• Ambidextrous• 8 Gauge yarn• Seamless
■ APPLICATIONS• Thermal Protection• Used in chain mail glove (lining)• Light duty handling glove• Light mechanical
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP6611
N/A
EN388
EN388-1120
Large
White/Off white
Yarn
Coating Material N/A
Cotton
Agricultural EngineeringAutomotive1120
Abrasion
PunctureTearCut
HP6611
grange
HP4100C PVC Medium weight glove - Knit wrist
■ FEATURES• PVC Coated/Cotton Liner• Elastic Cuff - Knitted wrist• Medium weight PVC Coating• Durable, washable, reusable
■ APPLICATIONS• Construction• General Handling• Wet Handling Glove• Agriculture
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4100C
Wrist Dip/knit wrist
SABS
MNF in accordance to SABS
10 - XL
Brown
Abrasion
PunctureTearCut
HP4101C
HP4103C
PVC Medium weight glove - Open Cuff ■ FEATURES
• PVC Coated/Cotton Liner• Open cuff/safety cuff 27cm• Medium weight• Durable/washable/reusable
■ APPLICATIONS• Construction• General handling• Wet handling• Agriculture• Light chemical protection
PVC Medium weight glove - Elbow Length ■ FEATURES
• PVC coated/cotton liner• Elbow length/ 38cm length• Medium weight• Durable/washable/reusable
■ APPLICATIONS• Construction• General Handling• Wet Handling• Agriculture• Light chemical protection• Submersible
Yarn
Coating Material Polyvinyl Chloride
Cotton
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4101C
Fully Coated/27cm
SABS
MNF in accordance to SABS
10 - XL
Brown
Yarn
Coating Material Polyvinyl Chloride
Cotton
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4103C
Fully Coated38cm
SABS
MNF in accordance to SABS
10 - XL
Brown
Yarn
Coating Material Polyvinyl Chloride
Cotton
Agricultural Chemical Construction
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Agricultural Chemical Construction
Agricultural Chemical Construction
HP4200C PVC Heavy weight glove - Knit wrist (Terry Palm) ■ FEATURES
• PVC Coated/Terry palm - Cotton• Elastic Cuff / Knit wrist• Heavy weight/Heavy duty• Durable, washable, reusable
■ APPLICATIONS• Construction• Abrasion application• Forestry/Agriculture
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4200C
Wrist dip/knit wrist
SABS
MNF in accordance to SABS
10 - XL
Brown
HP4201C
HP4203C
PVC Heavy weight glove - Open Cuff (Terry Palm)
■ FEATURES• PVC Coated/Terry palm - Cotton • Open cuff/safety cuff 27cm• Heavy weight/heavy duty• 18oz Terry toweling for extra protection
■ APPLICATIONS• Construction• Abrasion application• Roofing• Mining• Agricultural
PVC Heavy weight glove - Elbow Length (Terry Palm) ■ FEATURES
• PVC coated/Terry palm - cotton • Elbow length/ 37cm length• Heavy weight/heavy duty
■ APPLICATIONS• Construction• Abrasion application• Where forearm protection is needed• Forestry/Agriculture• Mining
Yarn
Coating Material Polyvinyl Chloride
Cotton/Terry towelline
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4201C
Fully Coated/27cm
SABS
MNF in accordance to SABS EN888
10 - XL
Brown
Yarn
Coating Material Polyvinyl Chloride
Cotton/Terry towelline
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4203C
Fully Coated
SABS
MNF in accordance to SABS
10 - Extra Large
Brown
Yarn
Coating Material Polyvinyl Chloride
Cotton/Terry towelline
grange
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Agricultural Construction Mining
Agricultural Construction Mining
Agricultural Construction Mining
HP4100G PVC Medium Weight Glove - Knit Wrist
■ FEATURES• PVC coated/Cotton liner• Knit Wrist• Smooth finish• Durable/Abrasive resistant
■ APPLICATIONS• Mining• Construction• Wet Handling• Agricultural
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4100G
Coated to knitted cuff
SABS
MNF in accordance to EN
10 - XL
Green
Yarn
Coating Material Polyvinyl Chloride
Cotton
Abrasion
PunctureTearCut
grange
PVC Medium Weight Reinforced Glove - Open Cuff
■ FEATURES• PVC coated/cotton liner• Open cuff 27cm• Reinforced between thumb and finger• Smooth finish• Durable/abrasive resistant
■ APPLICATIONS• Mining• Construction• Wet handling• Agriculture
PVC Medium Weight Reinforced Glove - Open Cuff ■ FEATURES
• PVC coated/cotton liner• Red left hand/Green right hand• Reinforced between thumb and finger• Smooth finish• Durable/abrasive resistant• Open cuff 27cm
■ APPLICATIONS• Mining• Construction• Wet handling• Agriculture
Item No.
Colour EN Rating
SizeHP4401GMNF in accordance to SABSGreen
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4401RG
Fully coated
SABS
MNF in accordance to SABSRed/Green
Yarn
Coating Material Polyvinyl Chloride
Cotton
10 - XL
Coating Range
SABS
Fully coated
SABSYarn
Material Polyvinyl Chloride
Cotton
10 - XL
HP4401G
■••••••
HP4401RG
Abrasion
PunctureTearCut
Abrasion
PunctureTearCut
Agricultural Construction Mining
Construction MiningFabrication Mining
Construction MiningFabrication Mining
grangePVC Medium Weight Reinforced Glove - Elbow Length
■ FEATURES• PVC coated/cotton liner• Open cuff 40cm• Reinforced between thumb and finger• Smooth finish• Durable/abrasive resistant• Added cradle for added longevity
■ APPLICATIONS• Mining• Construction• Wet handling• Agriculture
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4403G
Fully Coated
SABS
MNF in accordance to SABS
10 - XL
Green
Yarn
Coating Material Polyvinyl Chloride
Cotton
■••••••
HP4403G
Abrasion
PunctureTearCut
HP4403RGPVC Medium Weight Reinforced Glove - Elbow Length ■ FEATURES
• PVC coated/Cotton liner• Elbow length 40cm• Reinforced between thumb and finger• Smooth finish• Durable/Abrasive resistant• Added cradle for added longevity
■ APPLICATIONS• Mining• Construction• Wet Handling• Agricultural
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4403RG
Fully Coated
SABS
MNF in accordance to SABS
10 - XL
Red/Green
Yarn
Coating Material Polyvinyl Chloride
Cotton
Abrasion
PunctureTearCut
HP4403GRB PVC Rock Driller Glove (RNF Back) ■ FEATURES
• Impact Resistant Back• Reinforced Grip• 100% Coton Liner• 24oz Terry Padded Back• Supple palm for reduced hand fatigue
■ APPLICATIONS• Mining Glove• Rock Driving• Machine Operation• Material Sorting
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4403GRB
Fully COated
SABS
MNF in accordance to SABS
One size / 10
Green/Red
Yarn
Coating Material Polyvinyl Chloride
Cotton
4122
Abrasion
PunctureTearCut
Construction MiningFabrication Mining
Construction MiningFabrication Mining
Construction MiningFabrication Mining
HP5012Builders Glove - Black Latex ■ FEATURES
• Diamond grip• Superior Latex (more stretch)• .55mm in thickness• Length -33cm• Beaded cuff
■ APPLICATIONS• Sewer -Light duty• Submersible• Dexterous• Mixing of building materials
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP5012
Fully Coated
N/A
EN 388-4143
L, XL
Black
Yarn
Coating/Material Latex
N/A
Agricultural Chemical Fabrication
grange4143
Abrasion
PunctureTearCut
HP4201G PVC Heavy weight glove - Open Cuff
■ FEATURES• PVC Coated/Terry palm - Cotton • Open cuff/safety cuff 27cm• Heavy weight/heavy duty• 18oz Terry toweling
■ APPLICATIONS• Construction• Abrasion application• Roofing• Brick yards
Item No.
Colour
Coating Range
SABS
EN Rating
SizeHP4201G
Fully Coated
SABS
MNF in accordance to SABS EN888
10 - XL
Green
Yarn
Coating Material Polyvinyl Chloride
Cotton/Terry towelline
Abrasion
PunctureTearCut
Agricultural Construction Mining