www.prolabs.com Rev: 0920 1

34060607-C HUAWEI 6GBASE-SX eSFP MMF 850NM, 300M, LC, RGD 34060607-C Huawei® Compatible TAA Compliant 6GBase-SX eSFP Transceiver (MMF, 850nm, 300m, LC, Rugged) Features:

• Up to 6.144Gb/s bi-directional data links • SFF-8432 and SFF-8472 MSA Compliant • Built-in digital diagnostic functions • Duplex LC Connector • VCSEL transmitter and PIN receiver • 300m on 50/125um (OM3) MMF • Single power supply 3.3V and <0.8W low power dissipation • Operating Temperature: -40°C to +85°C • Support Hot Pluggable • Metal with lower EMI • Excellent ESD protection • RoHS compliant and Lead Free

Applications: • 6GBase-SX Ethernet • Wireless-CPRI

Product Description: This Huawei® 34060607 compatible SFP+ transceiver provides 6GBase-SX throughput up to 300m over multi-mode fiber (MMF) using a wavelength of 850nm via an LC connector. It is also capable of withstanding rugged environments and can operate at temperatures between -40°C to +85°C. It is guaranteed to be 100% compatible with the equivalent Huawei® transceiver. This easy to install, hot swappable transceiver has been programmed, uniquely serialized and data-traffic and application tested to ensure that it will initialize and perform identically. This transceiver is Trade Agreements Act (TAA) compliant. We stand behind the quality of our products and proudly offer a limited lifetime warranty. ProLabs' Transceivers are RoHS compliant and lead-free TAA refers to the Trade Agreements Act (19 U.S.C. & 2501-2581), which is intended to foster fair and open international trade. TAA requires that the U.S. Government may acquire only “U.S. – made or designated country end products.”

www.prolabs.com Rev: 0920 2

Regulatory Compliance • ESD to the Electrical PINs: compatible with MIL-STD-883E Method 3015.4 • ESD to the LC Receptacle: compatible with IEC 61000-4-3 • EMI/EMC compatible with FCC Part 15 Subpart B Rules, EN55022:2010 • Laser Eye Safety compatible with FDA 21CFR, EN60950-1& EN (IEC) 60825-1,2 • RoHS compliant with EU RoHS 2.0 directive 2015/863/EU

Absolute Maximum Ratings

Parameter Symbol Min. Typ. Max. Unit

Maximum Supply Voltage Vcc -0.5 4.0 V

Storage Temperature TS -40 85 °C

Operating Case Temperature Tc -40 85 °C

Operating Humidity RH 5 85 %

Receiver Power RMAX 0 dBm

Data Rate DR 6.144 Gbps

Bit Error Rate BER 10-12

Electrical Characteristics (TOP=25°C, Vcc=3.3Volts)

Parameter Symbol Min. Typ. Max. Unit Notes

Power Supply Voltage Vcc 3.14 3.30 3.46 V

Power Supply Current Icc 180 mA

Power Consumption PDISS 0.8 W

Transmitter

Single ended data input swing Vin,pp 90 800 mV

Input differential impedance Zin 100 Ω

Receiver

Single ended data output swing Vout, pp 185 425 mV

Output differential impedance Zin 100 Ω

Data output rise/fall time (20%-80%)

tr/tf 80 ps

www.prolabs.com Rev: 0920 3

Optical Characteristics Parameter Symbol Min. Typ. Max. Unit Notes

Transmitter

Output Optical Power Ptx -8.2 dBm 1

Optical Modulation Amplitude OMA 302 µW 2

Optical Extinction Ratio ER 3 dB

Optical Center Wavelength λc 840 850 860 nm

Spectral Width ∆λ 0.65 nm

Optical Rise/Fall Time (20%-80%) tr /tf 90 ps

Relative Intensity Noise RIN -128 dB/Hz Receiver

Receiver Sensitivity Rx_sen -11 dBm

Receiver overload Pol 0 dBm 2

Optical Return Loss ORL 12 dB

Optical Center Wavelength λc 770 860 nm

LOS Assert LOSA -30 dBm

LOS De-Assert LOSD -18 dBm

LOS Hysteresis LOSH 0.5 dB

Notes:

1. Class 1 Laser Safety per FDA/CDRH, and EN(IEC)60825 laser safety standards. 2. Exceeding the Receiver overload can physically damage the module. Please use appropriate

attenuation.

www.prolabs.com Rev: 0920 4

Pin Descriptions Pin Symbol Name/Descriptions Ref.

1 VeeT Transmitter Ground (Common with Receiver Ground). 1

2 TX Fault Transmitter Fault. LVTTL-O 2

3 TX Disable Transmitter Disable. Laser output disabled on high or open. LVTT-I. 3

4 SDA 2-Wire Serial Interface Data Line (Same as MOD-DEF2 in INF-8074i). LVTTL-I/O.

5 SCL 2-Wire Serial Interface Data Line (Same as MOD-DEF2 in INF-8074i). LVTTL-I.

6 MOD_ABS Module Absent, Connect to VeeT or VeeR in Module. 4

7 RS0 Rate Select 0. Not used 5

8 LOS Loss of Signal indication. Logic 0 indicates normal operation. LVTTL-O. 2

9 RS1 Rate Select 1. Not used 5

10 VeeR Receiver Ground (Common with Transmitter Ground). 1

11 VeeR Receiver Ground (Common with Transmitter Ground). 1

12 RD- Receiver Inverted DATA out. AC Coupled. CML-O.

13 RD+ Receiver Non-inverted DATA out. AC Coupled. CML-O.

14 VeeR Receiver Ground (Common with Transmitter Ground). 1

15 VccR Receiver Power Supply.

16 VccT Transmitter Power Supply.

17 VeeT Transmitter Ground (Common with Receiver Ground). 1

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. CML-I.

19 TD- Transmitter Inverted DATA in. AC Coupled. CML-O.

20 VeeT Transmitter Ground (Common with Receiver Ground). 1

Notes:

1. The module signal ground contacts, VeeR and VeeT, should be isolated from the module case. 2. This contact is an open collector/drain output and should be pulled up to the Vcc_Host with resister in

the range 4.7KΩ to 10KΩ. Pull ups can be connected to one or several power supplies, however the host board design shall ensure that no module contract has voltage exceeding module VccT/R +0.5.V.

3. Tx_Disable is an input contact with a 4.7KΩ to 10KΩ pull-up resistor to VccT inside module. 4. Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull the contract up to

Vcc_Host with a resistor in the range from 4.7KΩ to 10KΩ. Mod_ABS is asserted “High” when the SFP+ module is physically absent from a host slot.

5. Internally pulled down per SFF-8431

www.prolabs.com Rev: 0920 5

Pin-out of connector Block on Host board

Recommended Circuit Schematic

www.prolabs.com Rev: 0920 6

Mechanical Specifications Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA).

EEPROM Information EEPROM memory map specific data field description is as below:

www.prolabs.com Rev: 0920 7

About ProLabs Our experience comes as standard; for over 15 years ProLabs has delivered optical connectivity solutions that give our customers freedom and choice through our ability to provide seamless interoperability. At the heart of our company is the ability to provide state-of-the-art optical transport and connectivity solutions that are compatible with over 90 optical switching and transport platforms. Complete Portfolio of Network Solutions ProLabs is focused on innovations in optical transport and connectivity. The combination of our knowledge of optics and networking equipment enables ProLabs to be your single source for optical transport and connectivity solutions from 100Mb to 400G while providing innovative solutions that increase network efficiency. We provide the optical connectivity expertise that is compatible with and enhances your switching and transport equipment. Trusted Partner Customer service is our number one value. ProLabs has invested in people, labs and manufacturing capacity to ensure that you get immediate answers to your questions and compatible product when needed. With Engineering and Manufacturing offices in the U.K. and U.S. augmented by field offices throughout the U.S., U.K. and Asia, ProLabs is able to be our customers best advocate 24 hours a day. Contact Information ProLabs US Email: sales@prolabs.com Telephone: 952-852-0252 ProLabs UK Email: salessupport@prolabs.com Telephone: +44 1285 719 600