31459366 cswip question paper
TRANSCRIPT
8/10/2019 31459366 Cswip Question Paper
http://slidepdf.com/reader/full/31459366-cswip-question-paper 1/3
CSWIP 3.1 Quiz
Multi-Choice and QuestionsPaperFeb 2007
Printed On : 1/15/2015 @ 2:04:55 PM Page 1 of 3
1. Which of the following is the correct statement?
AC and DC can be used for MMA AC and DC can be used for TIG AC and DC can be used for SAW All of the above
2. A weld of dissimilar material is termed as….
Compound weld Transition weld Complex weld All of the above
3. What will you do if you find a consumable core wire is having rust on the surface?
Baking before use It is not important Rust should be completely removed by wiping with wool before use Quarantine for further investigation
4. What is “High Frequency” used for some welding process?
To reduce arc strike To give deep penetration For controlled arc To control interpass temperature
5. Why “Slope In” technique is used for TIG?
To reduce spatter To reduce tungsten inclusion To give arc stability
All of the above
6. Which of the following is a Rutile electrode?
6010 6013 6018 6016
7. Arc blow is associated with which of the following processes?
MMA TIG
SAW None of the above
8. What is added to steel for Deoxidation.
Sulphur Phosphorus Silicon Manganese
8/10/2019 31459366 Cswip Question Paper
http://slidepdf.com/reader/full/31459366-cswip-question-paper 2/3
CSWIP 3.1 Quiz
Multi-Choice and QuestionsPaperFeb 2007
Printed On : 1/15/2015 @ 2:04:55 PM Page 2 of 3
9. Fillet Fracture Test is conducted to….
Assess the strength Assess the root penetration and fusion Assess fracture failure Assess the toughness
10. Welding procedure qualification is…
To give welder practice To give instruction
11. Which effect does the cyclic loading have on a member?
Reduce strength Reduce Fatigue life Reduce toughness All of the above
12. Why hard stamping is not allowed on some welding fabrication?
It is too slow It can be safety hazard It may be damaging to the material All of the above
13. Which NDT method is effective for identifying laminations?
Radiography Test Magnetic Particle Test Ultrasonic Test
Dye Penetrant Test
14. MIG/MAG welding has a tendency to give lack of sidewall fusion when…
Spray transfer conditions are used 100% CO2 shielding gas is used Pulsed current is used Dip Transfer conditions are used
15. During PWHT of a complex fabrication, the heating rate and cooling rate are much higher than specified. Thismay….
Cause excessive oxidation
Not allow sufficient time to relieve stresses Introduce excessive compressive stresses Cause Distortion
16. A low heat input welding will have reduced….
Toughness Strength Residual Stress Harness
8/10/2019 31459366 Cswip Question Paper
http://slidepdf.com/reader/full/31459366-cswip-question-paper 3/3
CSWIP 3.1 Quiz
Multi-Choice and QuestionsPaperFeb 2007
Printed On : 1/15/2015 @ 2:04:55 PM Page 3 of 3
17. As the voltage of X-Ray set increases….
It increases the penetrating power It increases the wave length It increases the image quality All of the above
Theory Questions Asked in February 2007:
1. Explain your Duties as a Welding Inspector? Give a Mandatory Reference – Compulsory Question
2. As per BS 639 : 1987 E 44 42 R (13)
a. What gives Strength, Toughness and Positionb. Coveringc. Other characteristics
3. Why Hard Stamping is not used for some welding fabrications?
4. Explain TIG Processes.
5. Give four factors responsible for Hydrogen Cracking.
6. What is the requirement of Welding Procedure Test. Give 5 Essential Variables? DefineEssential Variable.
7. Explain Lamellar Tearing.
Note: The following is not exactly as it came in the exams (especially the multi choice). Ingeneral, there is a lot of twist in the questions asked.