MultiConnect® rCell 100 Series Router (C2, EV3)MTR-C2 and MTR-EV3 Quick Start

MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems

Quick Start Quick Start Quick Start Quick Start

Right Side Panel for MTR-C2

Right Side Panel for MTR-EV3

Side PanelsThe device has connectors on both sides of the housing. The right side ofthe device contains a reset button, a GPS and cellular connector for theC2. The EV3 includes the previously mentioned connectors along withWiFi and Auxiliary (for Diversity) connectors. Depending on the model,the WiFi or GPS connector may or may not be present. The left side ofthe device includes an RS-232 connector, an Ethernet connector, and thepower receptacle.

Installing the Router1. To use the router’s cellular features, connect a suitable

antenna to the antenna connector.2. Using an Ethernet cable, connect one end of it to the E-NET

connector on the router and the other end to your computer,directly or through a switch or hub.

3. If you are connecting to a serial interface, connect the DE-9connector (9-pin) of the RS-232 cable to the router's RS-232 connector. Connect the other end to the serial port onthe desired device.

4. Some routers support the use of a GPS receiver includingModel B17 for C2 and B08 for EV3. If you are using a GPSreceiver with the router, attach the GPS cable to the GPSconnector on the router.

5. Some routers support the use of WiFi including B09 andB10 for EV3. If you are using WiFi with the router, attach theWiFi antenna to the WIFI connector on the router.

6. Screw on power lead from power supply into powerconnection. Plug power supply into power source.

■ The POWER LED lights after the device powersup.

■ When the STATUS LED begins to blink, thedevice is ready for use.

7. You can configure your router by using your router’s webmanagement interface. You might need to change the IPaddress of your computer to be in the same IP and subnetmask range as the device.

a. Open web browser. In address field, type defaultaddress for router: http://192.168.2.1. (If browserdisplays a message about a problem with securitycertificate, ignore and click Continue).

b. For C2, a login page opens. Enter the defaultusername: admin (all lower-case). Then, enter thedefault password: admin (all lower-case). Click Login.

c. For EV3, when logging in for the first time, the deviceenters commissioning mode requiring a username andpassword for an admin user account. Enter and submitdesired username and password. Confirm password.

d. Refer to the appropriate user guide for further detailson first-time setup.

Mounting Device1. Locate the groove on the bottom of the modem.2. Slide the mounting rod through the groove.3. To secure the rod to the desired surface, place and tighten

two screws in the holes on either end of the mounting rod.Refer to the user guide for an illustration of the mountingrod, as well as the dimensions for placement of the screws.

MultiConnect® rCell 100 Series Router(MTR-C2/EV3)Part Number: 82102151L Rev 2.0

Copyright and TrademarksThis publication may not be reproduced, in whole or in part, without thespecific and express prior written permission signed by an executiveofficer of Multi-Tech Systems, Inc. All rights reserved. Copyright © 2018by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties,whether express, implied or by estoppels, with respect to the content,information, material and recommendations herein and specificallydisclaims any implied warranties of merchantability, fitness for anyparticular purpose and non-infringement. Multi-Tech Systems, Inc.reserves the right to revise this publication without obligation to notify anyperson or organization of such revisions or changes.

MultiConnect, MultiTech and the MultiTech logo are registeredtrademarks of Multi-Tech Systems, Inc. All other brand and productnames are trademarks or registered trademarks of their respectivecompanies.

MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems MultiConnect® rCell 100 Series Router (C2, EV3) MultiTech Systems

Quick Start Quick Start Quick Start Quick Start Quick Start

OverviewThe MultiConnect® rCell 100 Series Router (MTR-C2, MTR-EV3)provides secure data communication between many types of devices thatuse legacy and the latest communication technologies.

Regulatory InformationFor additional regulatory information, see device user guide or devicepage on www.multitech.com

47 CFR Part 15 Regulation Class B DevicesThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.■ Increase the separation between the equipment and receiver.■ Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.■ Consult the dealer or an experienced radio/TV technician for

help.

Warning: Changes or modifications to this unit not expressly approved bythe party responsible for compliance could void the user’s authority tooperate the equipment.

Package ContentsYour MultiConnect® rCell 100 Series Router (MTR-C2/EV3) typicallyincludes (varies with model):

PowerSupply

1 - 9 VDC power supply with removable blades, 1 -NAM blade/plug

Cables 1 - Ethernet cable with RJ-45 connector, 1 - Powercable from power supply

Antennas 1 - CELL, Dual Band EV-DO/CDMA externalantenna, 1 - GPS external antenna, and 1 - WIFIexternal antenna (EV3)

Documents 1 - Quick Start Guide, 1 - Warranty Plans, 1 -Activation, Support & Regulatory Information

Other Items 1 - Mounting rod, 4 - Clear adhesive bumpons ormounting feet

Device 1- MultiConnect® rCell 100 Series Router (C2, EV3)4.169" x 3.00" x 1.163" Blue enclosure includes:

■ 7-32 VDC Power connector■ RS-232 (DE 9-pin, female-D) connector■ E-NET RJ-45 receptacle for standard

Ethernet 10/100 Base-T■ WIFI WiFi male SMA connector (for EV3

only)■ AUX Cellular auxiliary female SMA

connector (Diversity - EV3 only)■ GPS GPS female SMA connector (B08

only for EV3, B17 only for C2)■ CELL Cellular female SMA connector

Additional InformationFor the latest information on your device, refer to the appropriate userguide online:

http://www.multitech.com/brands/multiconnect-rcell-100-series

LED DescriptionsThe top panel contains the following LEDs:

■ Power and Status LEDs - The Power LED indicates that DCpower is present and the Status LED blinks when the unit isfunctioning normally.

■ WiFi LED - The WiFi LED indicates that WiFi is enabled (EV3only).

■ Modem LEDs - Two modem LEDs indicate carrier detectionand link status.

■ Signal LEDs - Three signal LEDs display the signal strengthlevel of the wireless connection.

■ Ethernet LEDs - These LEDs are not on the top panel. Thetwo Ethernet LEDs are physically on the RJ-45 connector.

■ Ethernet Link LED - Located on the right on the Ethernetconnector. This LED blinks when there is transmit andreceive activity and is steady when there is a valid Ethernetconnection.

■ Ethernet Speed LED - Located on the left on the Ethernetconnector. When lit the Ethernet is linked at 100Mbps. If it isnot lit, the Ethernet is linked at 10 Mbps.

Activating CDMAFor CDMA devices, you need to associate the device radio with yourcellular service account so the radio connects to the service provider'scellular network. Before activating, contact your carrier to setup anaccount, check signal strength on LEDs and in the device UI. Ensure thedevice is receiving a strong signal. To activate your account:

1. From Cellular, select Activation. Note: The device'scurrent activation status is displayed, either ACTIVATED orNOT ACTIVATED. Also, a message appears below statusthat shows the device radio as activated or not.

2. If the device is not activated, follow the instruction for yourspecific carrier below. Each carrier activation is different.

a. Sprint: Uses an Over-The-Air activation process thatautomatically attempts to activate the radio once youarrive at the Activation window. For details onactivating using AT commands see the SprintActivation Guide for EV3/C2.

b. Verizon: Uses a one-click activation process. Click theActivate button. For details on activating using ATcommands see the Verizon Activation Guide forEV3/C2.

c. Aeris: Enter the MDN and MSID/MIN. Then click theActivate button. For details on activating using ATcommands see the Aeris Activation Guide for EV3/C2.

■ After the activation starts, a messagedisplays at the top of the screen that it is inprogress.

■ Once the activation completes, a messageappears at the top of the screen that itsucceeded or failed.

3. To verify the radio is activated, go to Verify Activation,enter an IP Address or URL, and use the default NetworkInterface as Radio. Click the PING button.

■ The device uses the cellular radio connection toping a server.

■ Once the ping completes, a message appears atthe top of the screen that it succeeded or failed.