2x2 Video Wall - NEC UN Series Displays - Installation Guide

Materials Checklist Suggested Tools for Installation Supporting Documents

● NEC UN Series LCD (x4)● OPS Media Player (x1)● OPS Media Player Caddie (x1)● Over-frame Kit (x2)● Remote Control Kit (x1)● 2x2 Video Wall Mount (x1)● 6’ Shielded Ethernet cable (x1)● 6’ Display Port cable (x4)● 6’ RS232 Control cable (x3)● USB Keyboard and Mouse (x1)● 6 Outlet Surge Suppressor (x1)● Velcro

Optional:● Hauppauge 1950 USB TV tuner (x1)● Coax Cable (x1)

● Laptop with USB to Serial adapter● Drill w/ metal, wood, and mortar bits● Phillips head screwdriver● Tape Measure● Level● Socket Set● Hex-end wrench set● Shims● Cable ties for final cable dressing● Screen cleaner and lint free cloth for

final clean up● This is a minimum list - review

statement of work to determine all tools needed.

Overview Documents● NEC X463UN Video Wall● NEC X551UN Video Wall● OPS Media Player● 2x2 Wall Mount● TV Tuner

Installation Guides

● OPS Media Player● 2x2 Video Wall Mount● Hauppauge 1950 USB TV tuner● Tile Matrix Configuration

2x2 Video Wall Mount OPS Media Player with Option board slot cover OPS Media Player Caddie

Revised 05-31-2012 Page 1

2x2 Video Wall - NEC UN Series Displays - Installation Guide

Step 1 - Preparation

1. Verify that installation location is ready (power, network, wall reinforced, adequate ventilation, coax cable if being installed)

2. Open all packages and lay everything out. Make sure all materials are present and there is no visible damage.

Installation Tip: If the installation location is not ready orany materials are missing or damaged, call the Rise DisplayProject Manager for instructions.

Revised 05-31-2012 Page 2

Step 2 - Install OPS Media Player

1. Select one of the LCD Displays and install the OPS Media Player per OPS Media Player Installation guide.

2. After installing the OPS Media Player, set display aside. This display will be Display #1.

3. Insert the keyboard and mouse USB dongle into a USB port on the OPS Media Player.

Step 3 - Install 2x2 Video Wall Mount and LCD Displays

1. Install 2x2 video wall mount and LCD Displays per 2x2 Wall Mount Installation guide. **Mounting configuration is the same for X551UN, X461UN, X462UN and X463UN**

Installation Tip: Leave adequate space between the left and right sides to access the rear of video wall and slide the displays together after cabling is completed. Installation Tip: The Ultra-Thin bezels on the UN displays are very easily damaged - take extreme caution during installation to avoid damage. Use cardboard between displays as you install and remove cardboard when displays are safely in place.

Revised 05-31-2012 Page 3

Step 4 - Connect all Cables Step 4A - RS232 Cables

1. Install RS232 Null Modem cables. Refer to RS232 Wiring Diagram at right.

Installation Tip: RS232 ports are labeled IN and OUT on display - double check to ensure you have cable connected to correct port - The RS232 OUTPUT ports are the ports closest to the wall when display is installed.

Front of Display

Revised 05-31-2012 Page 4

Step 4B - Display Port Cables

1. Install Display Port cabling. Refer to Display Port (DP) Wiring Diagram at right.

Installation Tip: Display Port (DP) ports are labeled IN and OUT on display - double check to ensure you have cable connected to correct port - As you are facing the front of the screen, the Display Port IN is on the left.

Front of Display

Revised 05-31-2012 Page 5

Step 4C - Infrared Remote and Ambient Light Sensor cable

1. Install Infrared Remote and Ambient Light Sensor cable at this time. You will not install the sensor until later.

2. Connect one end of the mini cable to the ‘Remote IN’ mini jack on display #1.

3. Leave the other end of the cable out and hanging where you will be able to get to it later when you install the sensor.

4. You will not be using the Remote OUT port

Installation Tip: Remote ports are labeled IN and OUT on display - double check to ensure you have cable connected to correct port - The Remote IN port is the port farthest from the wall when display is installed.

Front of Display

Revised 05-31-2012 Page 6

Step 4D - Power and Network

1. Connect one end of Ethernet patch cable to customer provided Ethernet jack - you will connect this to the Ethernet connection on the OPS Media Player in display 1.

2. Connect 6 outlet surge suppressor to customer provided AC outlet. You will connect all power cords from the displays and the external TV tuner (if used) to this surge suppressor.

Revised 05-31-2012 Page 7

Step 5 - Power up and configuration

1. Make sure the main power switch on each display is ON (The main power switch is located on the back of the display where the power cord connects)

2. Power on the 2x2 display by turning power on to each display individually.

3. Powering on display 1 will automatically power on the OPS Media Player.

Installation Tip: Make sure all 4 displays have the input set to Display Port using the remote control. If input is not set to Display Port, monitors will go into power save mode.

Important - you should now see the same image on all 4 displays

Revised 05-31-2012 Page 8

Step 5 - continued

1. Set up Tile Matrix on 2x2 video wall. This is done using the on screen menus on the NEC displays.

2. Refer to Tile Matrix configuration document for details.

Step 6 - Install and Configure TV If no TV is to be installed, skip this step

1. Install external USB TV Tuner per Hauppauge external USB TV tuner installation guide

Installation Tip - you will need the USB Keyboard and Mouse connected to the OPS Media Player for configuration of TV.

Revised 05-31-2012 Page 9

Step 7 - Install Over-frame Bezel Kit

1. Install over-frame Bezel Kit per Bezel Kit installation instructions for 2x2 video wall (page 2 of document - installation guide is also included in bezel kit box)

2. Use only the screws provided in the kit as any other screws may damage LCD displays.

Note: You were provided with 2 over-frame kits and it will require both to frame the 2x2 video wall.

Revised 05-31-2012 Page 10

Step 8 - Install Infrared Remote and Ambient Light Sensor

1. Install Infrared Remote and Ambient Light Sensor per Infrared Remote and Ambient Light Sensor installation guide. Installation guide is also included in sensor box.

2. Using any of the over-frame bezel attachment screws, attach the sensor in the best location for the client location - however, do not attach the sensor at the top center of either LCD display

3. After you have attached the sensor, connect the free end of the 3.5mm mini cable that you plugged into Remote IN in step 4D

Revised 05-31-2012 Page 11

Step 9 - Display Configuration

1. Reboot display by restarting Windows.2. Set up Power Schedule for displays if client wishes - using

on screen menus. (see page 27 of the NEC users manual)3. Disable buttons on NEC Displays. To activate the control

key lock function, press both and (on the display, not the remote) and hold down simultaneously for more than 3 seconds. To resume user mode, press both and hold simultaneously for more than 3 seconds.

4. Put Velcro on remote and attach to the back of the left side (as you are facing the front of the video wall) of display #3

Step 10 - Wrap Up

1. Remove all trash and extra parts - dispose of properly2. Clean up work area - wipe down displays3. Provide 3 remote controls, keyboard and mouse to client.4. Obtain written sign off from customer5. Take pictures of installation and email to

Sales@risedisplay.com and copy the Rise Display Project Manager.

6. Call the Rise Display Project Manager to review installation

Revised 05-31-2012 Page 12