ANS2-10LED SILICONE NEON FLEX

Color

Features

Application Bending Diameter

1. AC direct, eliminating the need and failure of DC driver2. Constant current IC for stable and reliable performance3. Top bending ideal for straight runs or mounting to a curved surface4. Max run 50m with uniform lighting5. Flexible, cuttable and dimmable6. Protections: Over voltage and under voltage

Landscape lighting, building outline,

steps, bridges, yards, roads, etc.

2835 IP67 115°4years

Light Surface

Base

Unit:mm

AC 220V

ANS2-10LED SILICONE NEON FLEX

Other Parameters

Model No.

Model No. LED Quantity(pcs)Series

Connection(m)

Mini Cuttable Length

(m)Max Run

(m)

Color TemperatureWavelength

(K/nm)

Luminous Flux[Typical]

(lm/m)

Efficacy(lm/m)

Voltage(V)

ANS2-10

ANS2-10 120 50 50 0.5

4119K

588.8nm

523.4nm

463.9nm

617.2nm

115°

≥80

/

/

/

/

33 8.8

8.8

8.8

8.8

8.8

34.1

22037.7

7.53

17.6

290.4

300.0

331.7

66.3

155.2

Beam Angle Ra Power(W/m)

-20~+60℃ -20~+70℃

Working Temperature

Storage Temperature

NOTE:Test environment temperature : 25±2°C.The above data is typical values. The actual data of each single product may differ from the typical values. The data is subject to change without notice.Different color temperature will make luminous flux different.

12

3

Installation

Optical & Electrical Parameters

By clips

ANS2-10LED SILICONE NEON FLEX

Length vs. power vs. voltage drop

Working Length(m)

1 0.044 220 217.3 217.3 0

0

0.2

0.6

0.7

1.7

2.5

3.7

4.8

5.7

6.1

217.1

216.9

216.5

216.1

215.1

214.3

213.1

212.0

211.3

210.7

217.1

217.1

217.1

216.8

216.8

216.8

216.8

216.8

216.8

216.8

8.8 -

-

-

-

-

-

-

-

-

-

-

44

88

132

176

220

264

308

352

396

440

220

220

220

220

220

220

220

220

220

220

0.224

0.446

0.669

0.892

1.114

1.337

1.56

1.78

2.0

2.2

EU standard plug

China standard plug

5

10

15

20

25

30

35

40

45

50

Rated Current(A)

Rated Voltage(AC V)

Rated Power(W)

Power Supply Method(DC V)

Voltage at the beginning(DC V)

oltage at the end (DC V)

Voltage Drop(DC V)

Profile DrawingUnit:mm

NOTE: Please ask the sales for detail drawing.

ANS2-10LED SILICONE NEON FLEX

AVERAGE BEAM ANGLE(50%)：115.7°C0/180,117.6°

C90/270,113.8°

Unit：cd

Luminous Intensity Distribution Diagram

Average IlluminationLuminous Flux output：208.9ml

Height Eavg，Emax Beam Angle：112.8° Diameter

NOTE:The test sample is 1m with color temperature of 4119K. Please ask the sales for data of other color temperature or colors.

ANS2-10LED SILICONE NEON FLEX

End exit (FREE)Quantity(50m):3pcs

3.5cm Aluminum track (Optional)

Quantity(50m):100pcs

Silicone glue (Optional)Quantity(50m):1pcs

End cap (FREE)Quantity(50m):3pcs

Screw (FREE)Quantity(50m):100pcs

Plastic clip (FREE)Quantity(50m):100pcs

Grip Plate (Optional)Quantity(50m):100pcs

Accessories

Packaging

Roll the product on thereel and tie it with PE film

Put the reel and accessory bag together into carton box

Accessories bag

Label the reel

Seal and label the box

Match each reel with accessory bag

Use packing belt to pack. Add edge protectors if necessary.

1

4

2

5

3

6

Model No.

ANS2-10 50000*15*10 375*375*200 1 14.15(1±10%) 16.95(1±10%)

Product Size（mm) Carton Size（mm) Total Quantity Net Weight(kg) Gross Weight(kg)

Packaging information

The above quantity and weight are only for the illustrated packaging method. There will be differences in the quantity and weight with other packaging methods.1 roll(50 m / strip) for a reel,and put it with accessories into one box.

Note:

ANS2-10LED SILICONE NEON FLEX

Installation

1.Tools

2.Accessories

Cutter Electric batch Brush

End exit (FREE)Quantity(50m):3pcs

3.5cm Aluminum track (Optional)

Quantity(50m):100pcs

Silicone glue (Optional)Quantity(50m):1pcs

End cap (FREE)Quantity(50m):3pcs

Screw (FREE)Quantity(50m):100pcs

Plastic clip (FREE)Quantity(50m):100pcs

Grip Plate (Optional)Quantity(50m):100pcs

Accessories can be provided according to customer's requirements

Note:

ANS2-10LED SILICONE NEON FLEX

3.Installation steps

4.Installation by clip

Installation of the end cap

Installation of end exit

Solder the wire to the PCB board

First put some glue inside of the plug, then push into the tape light

Screw the clip into the installation position

Then slowly press the tape light into the clip

The tape light is flatly and firmly stuck in the clip

Wipe off the excess glue and wait for the glue to solidify.

First put waterproof glue inside of the end exit, then push into the tape light

Wipe off the excess glue and wait for the glue to solidify

1

1

1 2 3

2

2

3

When soldering, pay attention to the positive and negative poles of wire and PCB board; positive to positive and negative to negative

1.

Each connection point must use 10g silicone glue, and treat waterproof and insulation well;

2.

Screw should perpendicular to installation surface and be fastened, as shown in the right.

3.

Note:

ANS2-10LED SILICONE NEON FLEX

5.AttentionsDo not do live-line working for high voltage product.1.

Follow the instructions of wiring diagram (first connect the load and then the power supply) to avoid short circuit.

2.

Make sure the correct connection of positive and negative poles between led module and power supply. Otherwise, the light will not be on.

3.

Make sure the power cord firmly screwed into the terminal as it can not be pulled out by hands.

4.

The terminal should have insulation, waterproof and anti-corrosive treatment.5.

Cuttable mark Neat and smooth cut Slide a spindle into the roll and then place the roll with spindle on top of the

box provided.

Gently unroll the fixture without excessive force.

Do not repeatedly bending This will damage

the circuit

Do not wring Do not bend 90° No embossing operation

No cutting distort No embossing operation

Do not twist

Warning

Cutting marks are on the PCB and can be observed outside.1.The above diagram only shows the correct or wrong way of operation, only as the reference.

2.

Note:

ANS2-10LED SILICONE NEON FLEX

Common Faults and Troubleshoot

Quick Guide Warning

Problems

All LEDs can not light on.

LEDs can not light on partly.

Brightness of LED is inconsistenttor insufficient.

LED flicker.

Automatic power protection from the open or short circuit in output of the power supply. Fix the short circuit problem.

Correctly connection

Check the power supply system to fix it.

Replace with more powerful power Make sure led module working voltage within ±5% of standard voltage, or keep balance by circuit power consumption.

Repair should be operated by a qualified technician, if the external circuit or main line of this product is damaged.The parameters given in this manual are typical values and for reference only.All illustrations and drawings in this manual are for reference.This product is subject to change without notice.

LED lighting products belongs to electronic products, please do recycling treatment according to the relevant WEEE directives.

Reduce the quantities of LED modules in series connection to meet requirement.

Fix the short circuit problem.

Wrong connection of power supply.

Some switching mode power supplies are not powered.

Power supply line error.

Mistaken wire connection of some of products

Power overloaded.

Connection point fault. Remove bad connection point.

Replace a new power supply.

Please follow the instructions

Power supply circuitexcessive consumption.

Excessive quantities in series connection of LED modules.

Switching power supply failure.

Wrong Installation or use ofproducts

Reasons

No electric supply.

SolutionsDo not disassemble or retrofit the light. Do not touch the surface of the light with a sharp object.

Do not do live-line working during installation,especially for high voltage product.

Do not use any organic chemical solvents.

Use neutral glass adhesive to fix this product and it needs to be dried 4 hours in the open environment after operation.

Treat the ends and the circuit connection points that are not connected to the main line with insulation,waterproof, and anti-corrosion in the installation.

Use 18AWG (0.75mm2 or thicker core wire to avoid adverse consequences caused by overheating, if the power cable need to lengthen.

Make sure the input voltage meets the requirements and lines are connected correctly before lighting on.This product is as backlight of signage, and do not use as general lighting.Series connection within the max run.

The length of the power cable between the power supply and the led strip should not exceed 2 meters.Otherwise, large circuit loss will lead to inconsistent brightness

Installation, maintenance and repair should be operated by a qualified technician.

Statements and Recycling

Statements:

Recycling: