2.63c 3€¦ · axle on rear chassis section up to a 20° total angle. transfer gearbox allowing...
TRANSCRIPT
2.63C3.63G
2.63C
WHEEL LOADERS
LITTLE BIG ONES.REDUCED SIZE, UNSTOPPABLE POWER
2.63C 2.63C› “Z” Linkage › Max power 50 HP› Bucket capacity 0.92 yd3 › Max permis. weight 10,582 lbs› Std operat. weight 9,149 lbs
› “Z” Linkage › Max power 50 HP› Bucket capacity 0.98 yd3 › Max permis. weight 10,582 lbs› Std operat. weight 9,590 lbs
3.63G› “Z” Linkage › Max power 60 HP› Bucket capacity 1.05 yd3 › Max permis. weight 12,677 lbs› Std operat. weight 10,803 lbs
Increase your expectations: Venieri’s small ones are here! Thanks to the widely tested project evolution matching the new market requirements, the new machines represent a significant improvement. We are located in the “Motor Valley” which, in a small territory, has always been giving birth to fabulous cars and top performing motorbikes!The genetic heritage is very rich: the Japanese technology of the Yanmar engines, new Bosch Rexroth transmissions and a ratio traction/weight never before achieved. The ORA (oscillating rear axle) is one of the main organs in this series: there isn’t any oscillating mechanical coupling between the front and rear, ensuring smart working and driving safety on these small ones which can be normally found on big machines only.
Extended performance rangeTractive Force F [lb]
Speed V [mph]
7,252 psi6,527 psi
+11%
ENGINE:JAPANESE TECHNOLOGY
TRANSMISSION:GLOBAL QUALITY
AXLE:TOP LEVEL
EQUIPMENT
GREASING:CENTRALIZED COMFORT
The 4 TNV 88 and 84T Yanmar engines are designed to match all types of requirements: low
environmental impact, low noise and limited vibration transform these engines perfect partners.
The continuous efforts to find sustainable solutions to essential needs of human life makes Yanmar enginesthe best in terms of power economy and emissions;
simplicity and reliability are the two main features that brought Venieri to choose Yanmar engines.
There are many ways to transmit power but only one is able to satisfy even the most demanding
customers: Venieri and Bosch-Rexroth laboratories have studied and developed one of the best possible combinations of high pressure transmission (so high efficiency
transmission with 7,252 psi). In that way the efficiency of Venieri’s wheel loaders led to a 11%
improvement: try and you’ll believe it!
The double fixing on each side grants extreme reliability and stiffness to the chassis even
after 8000/10000 working hours and represents a further confirmation of our design philosophy: small
size machines equally designed as the big ones! The 18° rear oscillation grants perfect stability and
security during working and transfer operations.Electrically driven 100% blocking slip differential.
Maintenance is fundamental on all machines: Venieri decided to build machines easy and accessible
to anyone: machines whose maintenance operations can be carried out in an easy and safe way, thanks
to its particular design. For example, the 3 points of centralized greasing allow the rear axle and the
swinging to be instantly double checked.
T E C H S P E C S
2.63CWHEEL LOADER › “Z” LINKAGE
DIESEL ENGINE
Engine: 4 cylinders, direct injection, water cooled, paper dry filter. Emissions in accordance with EC 97/68 Tier III rules.
Type ........................................................Yanmar 4TNV88 Max Power ................................................. 36kW - 50 HP Rated rpm ........................................................... 3,000Power ISO/TR 14396 ................................ 35 kW - 48 HPPower EEC/80/1269 ................................. 35 kW - 48 HPBore .......................................................... in 34.65Stroke ....................................................... in 35.43Displacement ............................................. in3 133,64
ELECTRIC SYSTEM
Battery ................................................................ 12 VoltCapacity EN 60095-1 ..................................80 Ah - 770 AAlternator rating ...................................................... 65 AReverse warning ............................................... StandardWiring according to rules ......................IP 67 e DIN 40050
TRANSMISSION
Hydrostatic transmission with automatic power regulation and closed circuit with variable-displacement pump and engine.Two forward/reverse speeds with single-lever control.
forward reverse1st Gear mph 0÷4 0÷42nd Gear mph 0÷12 0÷12
AXLES
All wheel drive. Two heavy duty axles with planetary final drives on each wheel. Fixed rigid drive axle on front chassis section. Oscillating drive axle on rear chassis section up to a 20° total angle.Transfer gearbox allowing the rear and the front movement by means of a transmission shaft. Self-locking limited slip differential on front axle (optional on rear axle).
BRAKES
Service: drum-brake hydraulically operating on front axle working on all wheels. Parking brake: mechanical drum-brake operating on service brake, manually activated.
TYRES
Standard .............................................. 12.0/75-18 12prOptional ........ 10.5-18 10pr • 12.5-18 10pr • 15.5/55 R18
STEERING
Servo assisted hydraulic steering with LOAD SENSING system.
Total steering angle .................................... 80°Inner tyres turning radius ............................ ft in 7’2.34”External tyres turning radius ....................... ft in 12’5.21”External bucket turning radius ...................... ft in 13’9.75”
HYDRAULIC SYSTEM
Hydraulic gear pump with LOAD SENSING priority valve for steering circuit. 2-section modular control valve with main relief valve. Double-acting hydraulic cylinders. Hydraulic oil cooling radiator. Full-flow oil filter on the return circuit. Single control cloche-lever with 4-position bucket lifting system and 3-position auxiliary control system.
Max flow .................................................. gpm 15.85Loader relief valve pressure ........................ psi 2,900.75Steering relief valve pressure ...................... psi 2,755.72Lifting cylinder .......................................... in 2.76x36.89Bucket cylinder ......................................... in 3.15x15.55
SERVICES CAPACITIES
Engine ...................................................... gal 2.11Front axle ................................................. gal 1.53Rear axle + gear box ................................. gal 1.72Hydraulic circuit ......................................... gal 15.06Brake system ............................................ gal 0.29Fuel .......................................................... gal 18.49Water cooling ............................................ gal 2.64
TECHNICAL FEATURES
Standard bucket capacity ............................ yd3 0.92Bucket width ................................................ft in 5’6.93”Straight static tipping load ........................... lbs 6,614Full turned 40° tipping load ............................. lbs 5,952Lifting capacity at max. height ...................... lbs 5,952Dump clearance.......................................... ft in 10’2.05”Dump height at 43° ..................................... ft in 8’0.46”Reach at 43° .............................................. ft in 2’1.59”Breakout force ........................................... lbs 10,362
DIMENSIONS AND WEIGHT
Max lenght in transfer position ..................... ft in 15’8.98”Max width in transfer position ...................... ft in 5’6.93”Max height ................................................ ft in 8’0.85”Track width ................................................ ft in 4’3.97”Overall tyre width ....................................... ft in 5’4.57”Wheel base ................................................ ft in 6’4.77”Ground clearance ....................................... in 14.57” Standard operating weight ........................... lbs 9,149Max permissible weight .............................. lbs 10,582
3’11.24”5’5.75”
2’1.59”
6’4.77”
8’0.85”
8’6.76”
8’0.46”
2.56”
10’2.05”
12’5.61”
6’4.77” 5’4.96”
11°30°
43°
56°
42°
UNIVERSAL MULTI PURPOSE PERFORMANCE DATA BUCKET BUCKET OVERSIZE FORKS
Full load bucket capacity (SAE) yd3 0.98 0.78 1.57 /
Bucket width ft in 5’6.93” 5’6.93” 6’2.8” /
Bucket weight lbs 551 551 772 /
Max operative height ft in 12’5.61” 12’3.64” 12’7.57” /
Forks lenghth (Standard) ft in 3’3.37”
Forks lenghth (Optional) ft in 3’11.24”
Height to hinge pin ft in 10’2.05” 10’2.05” 10’2.05” /
Dump angle ° 43° 43° 43° /
Dump height ft in 8’0.46” 8’2.43” 7’10.49” /
Reach fully raised ft in 2’1.59” 1’11.62” 2’3.56” /
Max dump distance ft in 4’9.09” 4’7.12” 4’11.06” /
Bucket static tipping load, straight lbs 6,614 6,393 5,952 /
Bucket static tipping load, full turn (40°) lbs 5,952 5,732 5,291 /
Forks static tipping load, full turn (40°) lbs 4,850
Forks Payload EN 474-3 (80%) lbs 3,880
Forks Payload EN 474-3 (60%) lbs 3,086
Breakout force lbs 10,362 11,244 9,700 /
Total length ft in 15’8.98” 15’7.01” 15’8.98” /
External bucket turning radius ft in 13’9.35” 13’1.48” 14’1.29” /
Standard operative weight lbs 9,149 9,259 9,259 /
T E C H S P E C S
2.63CWHEEL LOADER › “Z” LINKAGE
DIESEL ENGINE
Engine: 4 cylinders, direct injection, water cooled, paper dry filter. Emissions in accordance with EC 97/68 Tier III rules.
Type ........................................................Yanmar 4TNV88 Max Power ................................................. 36kW - 50 HP Rated rpm ........................................................... 3,000Power ISO/TR 14396 ................................ 35 kW - 48 HPPower EEC/80/1269 ................................. 35 kW - 48 HPBore .......................................................... in 34.65Stroke ....................................................... in 35.43Displacement ............................................. in3 133,64
ELECTRIC SYSTEM
Battery ................................................................12 VoltCapacity EN 60095-1 ................................. 80 Ah - 770 AAlternator rating ......................................................65 AReverse warning ............................................... StandardWiring according to rules ..................... IP 67 e DIN 40050
TRANSMISSION
Hydrostatic transmission with automatic power regulation and closed circuit with variable-displacement pump and engine.Two forward/reverse speeds with single-lever control.
forward reverse1st Gear mph 0÷4 0÷42nd Gear mph 0÷17 0÷17
AXLES
All wheel drive. Two heavy duty axles with planetary final drives on each wheel. Fixed rigid drive axle on front chassis section. Oscillating drive axle on rear chassis section up to a 20° total angle.Transfer gearbox allowing the rear and the front movement by means of a transmission shaft. Electriccaly driven 100% blocking slip differential, on front axle and open on rear axle.
BRAKES
Service: drum-brake hydraulically operating on front axle working on all wheels. Parking brake: mechanical drum-brake operating on service brake, manually activated.
TYRES
Standard ............................................. 12.0/75-18 12prOptional ........10.5-18 10pr • 12.5-18 10pr • 15.5/55 R18
STEERING
Servo assisted hydraulic steering with LOAD SENSING system.
Total steering angle .................................... 80°Inner tyres turning radius ............................ ft in 7’2.34”External tyres turning radius ....................... ft in 12’5.21”External bucket turning radius ...................... ft in 13’9.75”
HYDRAULIC SYSTEM
Hydraulic gear pump with LOAD SENSING priority valve for steering circuit. 2-section modular control valve with main relief valve. Double-acting hydraulic cylinders. Hydraulic oil cooling radiator. Full-flow oil filter on the return circuit. Single control cloche-lever with 4-position bucket lifting system and 3-position auxiliary control system.
Max flow .................................................. gpm 15.85Loader relief valve pressure ........................ psi 3,335.87Steering relief valve pressure ...................... psi 2,755.72Lifting cylinder .......................................... in 2.76x36.89Bucket cylinder ......................................... in 3.15x15.55
SERVICES CAPACITIES
Engine ...................................................... gal 2.11Front axle ................................................. gal 1.53Rear axle + gear box ................................. gal 1.72Hydraulic circuit ......................................... gal 15.06Brake system ............................................ gal 0.29Fuel .......................................................... gal 18.49Water cooling ............................................ gal 2.64
TECHNICAL FEATURES
Standard bucket capacity ............................ yd3 0.98Standard bucket width .................................. ft in 5’6.93”Straight static tipping load ........................... lbs 7,275Full turned 40° tipping load ............................. lbs 6,614Lifting capacity at max. height ...................... lbs 6,834Dump clearance.......................................... ft in 10’2.05”Dump height at 43° ..................................... ft in 8’0.46”Reach at 43° .............................................. ft in 2’1.59”Breakout force ........................................... lbs 11,684
DIMENSIONS AND WEIGHT
Max lenght in transfer position ..................... ft in 15’8.98”Max width in transfer position ...................... ft in 5’6.93”Max height ................................................ ft in 8’0.85”Track width ................................................ ft in 4’3.97”Overall tyre width ....................................... ft in 5’4.57” Wheel base ................................................ ft in 6’4.77”Ground clearance ....................................... in 14.57”Standard operating weight ........................... lbs 9,590Max permissible weight .............................. lbs 10,582
3’11.24”5’5.75”
2’1.59”
6’4.77”
8’0.85”
8’6.76”
8’0.46”
2.56”
10’2.05”
12’5.61”
6’4.77” 5’4.96”
11°30°
43°
56°
42°
UNIVERSAL MULTI PURPOSE PERFORMANCE DATA BUCKET BUCKET OVERSIZE FORKS
Full load bucket capacity (SAE) yd3 0.98 0.78 1.57 /
Bucket width ft in 5’6.93” 5’6.93” 6’2.8” /
Bucket weight lbs 551 551 772 /
Max operative height ft in 12’5.61” 12’3.64” 12’7.57” /
Forks lenghth (Standard) ft in 3’3.37”
Forks lenghth (Optional) ft in 3’11.24”
Height to hinge pin ft in 10’2.05” 10’2.05” 10’2.05” /
Dump angle ° 43° 43° 43° /
Dump height ft in 8’0.46” 8’2.43” 7’10.49” /
Reach fully raised ft in 2’1.59” 1’11.62” 2’3.56” /
Max dump distance ft in 4’9.09” 4’7.12” 4’11.06” /
Bucket static tipping load, straight lbs 7,275 7,055 6,393 /
Bucket static tipping load, full turn (40°) lbs 6,614 6,393 5,952 /
Forks static tipping load, full turn (40°) lbs 5,291
Forks Payload EN 474-3 (80%) lbs 4,233
Forks Payload EN 474-3 (60%) lbs 3,175
Breakout force lbs 11,905 12,787 11,244 /
Total length ft in 15’8.98” 15’7.01” 15’8.98” /
External bucket turning radius ft in 13’9.35” 13’1.48” 14’1.29” /
Standard operative weight lbs 14’3.26” 15’5.04” 15’5.04” /
TRANSMISSION
% Traction/Weight 71 %
Pump 7252 psi
Hydrostatic engine 7252 psi
DIESEL ENGINE
4-cylinder engine: port fuel injection, water cooling, paperdry filtering. Emissions as per EC 97/68 Tier III rules.
Type .......................................................Yanmar 4TNV84T Max Power ................................................ 44 KW - 60 HP Rated rpm ............................................... 3,000Power ISO/TR 14396 ................................ 42 KW - 57 HPPower EEC/80/1269 ................................. 42 KW - 57 HPBore ......................................................... in 33.07Stroke ...................................................... in 35.43Displacement ............................................ in3 121,74
ELECTRIC SYSTEM
Battery .................................................................12 VoltCapacity EN 60095-1 .................................100 Ah - 850 AAlternator rating .......................................................40 AReverse warning ................................................ StandardWiring according to rules ...................... IP 67 e DIN 40050
TRANSMISSION
Hydrostatic transmission with automatic power regulation and closed circuit with variable-displacement pump and engine.Two forward/reverse speeds with single-lever control.
forward reverse1st Gear mph 0÷6 0÷62nd Gear mph 0÷19/21* 0÷19/21*(*) High speed optional.
AXLES
All wheel drive. Two heavy duty axles with planetary final drives on each wheel. Fixed rigid drive axle on front chassis section. Oscillating drive axle on rear chassis section up to a 20° total angle.Transfer gearbox allowing the rear and the front movement by means of a transmission shaft. Self-locking limited slip differential on front axle (optional on rear axle).
BRAKES
Service: drum-brake hydraulically operating on front axle working on all wheels. Parking brake: mechanical drum-brake operating on service brake, manually activated.
TYRES
Standard ................................................... 405/70 R18”Optional .....................................................12,5-20” 12pr
STEERING
Servo assisted hydraulic steering with LOAD SENSING system.
Total steering angle .................................... 80°Inner tyres turning radius ............................ ft in 2.220External tyres turning radius ....................... ft in 4.050External bucket turning radius ...................... ft in 4.350
HYDRAULIC SYSTEM
Hydraulic gear pump with LOAD SENSING priority valve for steering circuit. 2-section modular control valve with main relief valve. Double-acting hydraulic cylinders. Hydraulic oil cooling radiator. Full-flow oil filter on the return circuit. Single control cloche-lever with 4-position bucket lifting system and 3-position auxiliary control system.
Max flow .................................................. gpm 15.85Loader relief valve pressure ........................ psi 3,335.87Steering relief valve pressure ...................... psi 2,755.72Lifting cylinder .......................................... in 2.76x23.19Bucket cylinder ......................................... in 3.15x15.55
SERVICES CAPACITIES
Engine ...................................................... gal 1.98Front axle ................................................. gal 1.53Rear axle + gear box ................................. gal 1.72Hydraulic circuit ......................................... gal 15.06Brake system ............................................ gal 0.29Fuel .......................................................... gal 18.49Water cooling ............................................ gal 2.64
TECHNICAL FEATURES
Standard bucket capacity ............................ yd3 1.05Bucket width ................................................ft in 6’2.8”Straight static tipping load ........................... lbs 8,488Full turned 40° tipping load ............................. lbs 7,606Lifting capacity at max. height ...................... lbs 5,512Dump clearance.......................................... ft in 10’5.98”Dump height at 40° ..................................... ft in 8’6.36”Reach at 40° .............................................. ft in 2’3.56”Breakout force ........................................... lbs 11,684
DIMENSIONS AND WEIGHT
Max lenght in transfer position ..................... ft in 16’0.36”Max width in transfer position ...................... ft in 6’2.8”Max height ................................................ ft in 8’4.39”Track width ................................................ ft in 4’5.54”Overall tyre width ....................................... ft in 5’11.65”Wheel base ................................................ ft in 6’8.16”Ground clearance ....................................... in 13.39”Standard operating weight ........................... lbs 10,803Max permissible weight .............................. lbs 12,677
T E C H S P E C S
3.63GWHEEL LOADER › “Z” LINKAGE
40°49°
40°
8’6.
36”
6’8.16” 4’11.92”
40
2’3.56”
10’5.9
8”12
’11.
51”
34°
14°
6’8.16”3’11.24” 5’4.96”
8’4.
39”
8’10
.3”
UNIVERSAL MULTI PURPOSE PERFORMANCE DATA BUCKET BUCKET OVERSIZE FORKS
Full load bucket capacity (SAE) yd3 1.05 0.92 1.96 /
Bucket width ft in 6’2.8” 6’2.8” 6’10.68” /
Bucket weight lbs 716 992 992 /
Max operative height ft in 8,708 8,267 8,598 /
Forks lenghth (Standard) ft in 3’3.37”
Forks lenghth (Optional) ft in 3’11.24”
Height to hinge pin ft in 10’5.98” 10’5.98” 10’5.98” /
Dump angle ° 40° 40° 40° /
Dump height ft in 8’6.36” 8’7.35” 8’2.43” /
Reach fully raised ft in 2’3.56” 2’4.74” 2’5.53” /
Max dump distance ft in 6’6.74” 6’4.77” 6’10.68” /
Bucket static tipping load, straight lbs 8,488 9,039 8,047 /
Bucket static tipping load, full turn (40°) lbs 7,606 8,157 7,165 /
Forks static tipping load, full turn (40°) lbs 5,842
Forks Payload EN 474-3 (80%) lbs 4,674
Forks Payload EN 474-3 (60%) lbs 3,505
Breakout force lbs 10,362 11,023 9,700 /
Total length ft in 16’0.36” 16’2.33” 16’2.33” /
External bucket turning radius ft in 14’3.26” 14’1.29” 14’5.23” /
Standard operative weight lbs 10,803 11,023 11,023 /
80° articulation.Cramped conditions do not scare us.
Arms Connection with ovalized section. We want to see clearly!
Steering console.A master piece for all job requirements!
Framed glass door and flat glass.We combine style with efficiency!
Multipurpose Joystick. You can do everything with one hand!
Linkage connection on the chassis with cantilevered pins.+ performance, better visibility = less risk!
Evolved and complete hydraulic.Not only High Flow kit but also additional hydraulic kit for tools and equipments. An example?Hand operated hydraulic demolition hammer!
Hydraulic quick coupling.Use your Venieri as a universal tool carrier thanks to the interchangeability of most quick couplings/equipment!
EQUIPMENT
FORWARD/REVERSE
SLOW/FAST
SELF LOCKING DEVICE
100% ON DEMAND
EQUIPMENT
• Standard O Optional -- Not available
(20
19
)
UP
56
4_U
S_A
-Impe
rial
The illustrations on the present folder do not necessarily show the product standard version. Data and dimensions described in this folder are not binding.Venieri reserves the right of carrying out possible changes at any time and without previous notice because of its policy of steady developement and improvement of the products.
Via Piratello, 106 - 48022 Lugo (RA) ITALY Tel. +39 0545 904411 - Fax +39 0545 30389
e-mail: [email protected] www.vf-venieri.com
EQUIPMENT
› Acoustic warnings› Plugs with keys for fuel and hydraulic tanks› Bucket with bolted teeth› ROPS-FOPS cab with heating and pressurization fan, with front and rear windscreen wiper and windshield washer› Tool box› Spare parts catalogue› Seat belt› Electrically driven 100% blocking slip differential on front axle › Safety clamp for lifting cylinders› Visual index for bucket position› Working lights› Draw bar hook› Soundproofing› Yellow rotating and overturning beacon› Operation and maintenance manual› Type-approval for road traffic› Side rearview mirrors› Complete instrument panel› Hydraulic or mechanical quick coupler› Cement mixing bucket› Multipurpose bucket (4 in 1)› Speed reduction kit › Lifting forks› Proportional self lock rear differential› Electrically driven 100% blocking slip differential on front axle; open on rear axle› Asphalt and cement planer› Snow blower› “V” type snow blade› Angle-tilt dozer blade› Hand operating hammer› Polishing brush› Trencher
••••
••••••••••••••OOOOOO•OOOOOOO
2.63C 2.63C 3.63G••••
••••••••••••••OOOOO--
--
OOOOOOO
••••
••••••••••••••OOOOOOOOOOOOOO
O R I G I N A L