220 mobile piston pump catalog design code b

220 Mobile Piston Pump CatalogDesign Code B

AEC018 280 bar [4060 psi] AEC028 280 bar [4060 psi]

Content

EATON 220 MOBILE PISTON PUMP CATALOG E-PUOV-TP001-E8 August 2019 www.eaton.com

Model codes 2

Specifications and performance 4

Control optionsPressure & Flow (Load Sense) Compensator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pressure Compensator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Pressure Control (RPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Electronic Displacement Control (EDC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

EH Inverse Proportional Pressure Control (IPPC) . . . . . . . . . . . . . . . . . . . . . . . . . 10

Electronic Destroke (Cold Start) Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Performance AEC018 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12–13

AEC028 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14–15

Pump installationAEC018 A-Mount standard - side-ported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

AEC018 A-Mount AG version - rear ported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

AEC028 B-Mount - rear-ported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AEC028 B-Mount - side-ported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

AEC028 Thru drive SAE-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

AEC028 Thru drive SAE-B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

AEC018- Pressure & Flow (Load Sense) Compensator . . . . . . . . . . . . . . . . . . . . 22

Control installationAEC-028 Pressure & Flow (Load Sense) Compensator . . . . . . . . . . . . . . . . . . . . 23

ACE028- Electronic Displacement Control (EDC) . . . . . . . . . . . . . . . . . . . . . . . . . 24

AEC018 Maximum Stroke Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

AEC018 Cold start valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Input shaft options 27-28

Installation and start-up 29

EATON 220 MOBILE PISTON PUMP CATALOG E-PUOV-TP001-E8 August 2019 www.eaton.com1

Introduction220 Series Piston Pump

The Eaton® X20 portfolio of open-circuit piston pumps is built to maximize machine performance and productivity . With sophisticated controls that enhance system efficiency and a compact design that delivers incredible power, the X20 portfolio empowers mobile machine operators to do more work in less time using less fuel .

Sophisticated controls that improve performance while optimizing efficiency.

Excellent pressure responsiveness – The X20 portfolio delivers the fastest response and recovery times in the open-circuit piston segment, helping customers get the job done faster .

Low standby pressure – The X20 portfolio can maintain low margin pressure (~150 psi) with exceptional stability, reducing heat generation and helping to eliminate wasted energy .

Stable fan drive functionality – Eaton’s fan drive control reaches desired speed more quickly and remains stable once there, reducing energy-wasting oscillation .

Advanced electronic controls – The cold start and fan drive controls are Pro-FX Ready, meaning they can be easily configured with pre-programmed development tools and controlled electronically for maximum flexibility and precision .

Winning load sense combination – X20 works in conjunction with Eaton’s CLS Load Sense Sectional Mobile Valve, providing OEMs one resource for their machine’s load sense needs .

Compact design that enables greater flexibility and cost savings.

Simplified pump architecture – The X20 pump has 25% fewer components than traditional pumps, reducing the number of leak points and simplifying maintenance .

Compact package size – The X20 portfolio’s small size satisfies Tier 4 requirements and provides more flexibility when designing the engine compartment .

More horsepower – The compact rotating group delivers a remarkable amount of horsepower, improving productivity without using more fuel .

One-piece housing – Single-piece pump housing removes leak points and makes maintenance faster and easier versus more complicated multi-piece housings .

Multiple options that make it easy to specify exactly what you need.

Variety of control options – Including pressure control, load sense, cold start, torque control, remote pressure control, inverse proportional pressure control, proportional pressure control, electronic displacement control, and swash sensor feedback, giving you more ways to design more efficient, productive machines .

Several displacement options – With seven displacement options, there’s an X20 pump to fit virtually any mobile application need . The 220 series is currently available in 18cc (1 .09 cu . inch) & 28cc (1 .71 cu . inch) displacement . It is rated for 280 bar & up to 3,600 rpm and is capable of generating upto 52 .6 horsepower (39 .2kW), making it the ideal pump for an array of different mobile and stationary applications . The combination of high load capacity bearings and a stiff drive shaft help provide a pump B10 bearing life of up to 5,850 hours at rated mobile conditions, reducing operating costs and extending operating life .

Variety of mounting options – The X20 portfolio is available with both SAE and ISO mounting flange configurations, can be side- or rear-ported, and offers multiple drain ports to help overcome any installation challenges

Exceptional quality that provides remarkable reliability.

Unique control piston design – Single-acting control piston with special coating helps minimize friction, increasing operating life .

Bronze piston shoes – Bronze piston shoes are robust against contamination should particles enter the fluid, enhancing system performance and component service life .

High-load bearings – Larger, more durable bearings resist wear and deliver industry-leading bearing life .

3-year manufacturer’s warranty – Eaton’s warranty terms provide peace of mind for three full years, helping you get through your warranty period with complete confidence .

Global network of Eaton-certified experts for end-to-end support.

More partners in more regions – Growing network of Eaton distributors around the world ensures there’s local service and support anywhere you need it .

World-class system design and assembly – Our expert distribution partners can help with everything from specifying to prototyping and assembly to commissioning, so you can focus on other areas of your business .

Eaton-standardized practices and processes – Eaton employs a unique system of tools and processes, known as the Eaton Business System, to ensure quality development and delivery of the X20 product . These tools and process include such known methods as Design for Six Sigma, Lean Manufacturing and ISO certification .

EATON 220 MOBILE PISTON PUMP CATALOG E-PUOV-TP001-E8 August 2019 www.eaton.com 2

Model codes220 Series Mobile Piston Pump

1 2 3 Pump seriesAEC – 220 Series open circuit piston pump

4 5 6 Pump displacement018 – 18 .0 cm3/r [1 .09 in3/r]028 – 28 .0 cm3/r [1 .71 in3/r]

7 Input shaft rotationL – Left handR – Right hand

8 9 Front mount and shaft05 – 2 Bolt B, 22 .2 mm (0 .88) dia . keyed shaft09 – 2 Bolt B, 13 Tooth 16/32 Spline31 – 2 Bolt B, 25 .4 mm(1 .00 in) dia . straight keyed34 – 2 Bolt B, 15 Tooth 16/32 spline48 – 2 Bolt A, 11 Tooth 16/32 spline, 38 mm [1 .5 in] ext .

[18cc only]49 – 2 Bolt A, 1:8 Taper 16 .66 mm [0 .655 in] dia . 39 .7

[1 .56] ext [for 18cc AG variant only]50 – 2 Bolt A, 9 Tooth 16/32 spline [for 18cc only]51 – 2 Bolt A, 19 .02 mm [ .749 in] dia . keyed shaft, 32 mm

[1 .26 in] ext . [for 18cc only]52 – 2 Bolt A, 15 .85 mm [ .324 in] dia . keyed shaft, 32 mm

[1 .26 in] ext . [for 18cc only]

10 11 Main ports size & locationAA – Rear port Suction - 1 .625 - 12 SAEO-Ring Pressure - 1 .0625 - 12SAE O-RingAB – Side Port Suction - 1 .625 - 12 SAEO-Ring Pressure - 1 .0625 - 12 SAE O-RingAC – Rear port [for 28cc only] Suction - M42 X 2 Metric O-Ring, Pressure - M27 X 2 Metric O-RingAD – Side port Suction - M42 X 2 Metric O-Ring Pressure - M27 X 2 Metric O-RingAE – Rear port [for 28cc only] Suction - 1 .25” (code 61) with .4375 - 14

UNC- 2B Threads, Pressure - .75” (Code 61) with .375 - 16

UNC -2B ThreadsAF – Side port suction - 1 .25” (Code 61) with .4375 - 14

UNC- 2B threads Pressure - .75” (Code 61) with .375 - 16

UNC -2B threadsAG – Rear ports [for 28cc only] Suction - M48 Metric O-Ring, Pressure - M33 Metric O-Ring

12 Case drain portsA – .875 - 14 SAE O-ring - topB – .875 - 14 SAE O-ring - bottomC – M22 X 1 .5 metric o-ring - top D – M22 X 1 .5 metric o-ring - bottomG – .75 - 16 SAE O-ring - verticalH – M18 X 1 .5 Metric o-ring - verticalL – .75-16 SAE O-ring – top

1 2 3

AEC

4 5 6

028

7

R

8 9

05

10 11

AB

12

A

13

1

14 15

AA

16 17

28

18 19

20

20 21

00

22 23

00

24 25

01

26 27

00

28

1

29 30

00

31 32

CD

33 34

01

35

B

13 Diagnostic pressure ports1 – .4375 - 20 SAE O-ring port - plugged2 – M12 X 1 .5 metric O-ring port - plugged

14 15 Controller typeAA – Pressure flow compensator with

.4375 - 20 SAE o-ring load sense port# AB – Pressure flow compensator with M12 X 1 .5 Metric

o-ring load sense portAC – Pressure compensator onlyAP – Remote pressure control M12

metric O-ring port, left side [for 28cc only]AT – Pressure and flow compensator with electronic dis-

placement control - EP type [for 28cc only]AV – EH inverse proportional pressure control

(vertical mounting) [for 28cc only]AW – Remote pressure control with

.4375-20 SAE o-ring port, left side#AY – Pressure and flow compensator with electronic

displacement control - EPD type [for 28cc only]BB – Pressure comp . w/electro hyd . proportional

pressure control (EHPPC) [for 28cc only]BH – Remote pressure control w/ M12 x 1 .5 metric o-ring

port (left side) & electronic displacement control - EP type [for 28cc only]

16 17 Pressure compensator setting (Tolerance on setting)*

02 – 76 - 83 bar (1100-1200 lbf/in2)26 – 197 - 203 bar (2850-2950 lbf/in2)34 – 234 - 241 bar (3400-3500 lbf/in2)43 – 276 - 283 bar(4000-4100 lbf/in2)

18 19 Flow compensator / remote pressure control setting (tolerance on setting)

00 – No flow compensator setting14 – 12 - 15 bar (180-220 lbf/in2)20 – 17 - 20 bar (250-290 lbf/in2)

20 21 Torque control setting 00 – No torque control

22 23 Control special features00 – No control special features0A – Bleed down orifice0B – 24V Cold start valve0S – 12V DC Solenoid AMP Jr connector

(used with EH inverse proportional pressure control)

0P – Load sense steel tube connected to integrated shuttle valve [for 18cc AG pump only]

0T – 24V DC Solenoid AMP Jr connector (used with EH inverse proportional pressure control)

0U – 12V DC solenoid deutsch connector (used with EH inverse proportional pressure control)

0V – 24V DC solenoid deutsch connector (used with EH inverse proportional pressure control)


Model codes220 Series Mobile Piston Pump

24 25 Maximum displacement option*01 – Standard displacement

(as given in code title)02 – External manual stroke adjustment

set at max

26 27 Auxiliary (rear) mount & output shaft [for 28cc only]

00 – No auxiliary mounting featuresAA – SAE A -2 Bolt, 9T 16/32 splineAB – SAE A- 2 Bolt, 11T 16/32 splineAC – SAE B- 2 Bolt, 13T 16/32 splineAG – Auxiliary mount ready with cover plate

28 Shaft seal1 – Standard viton shaft seal2 – Nitrile shaft seal

29 30 Pump special features 00 – No special featuresAB – Swash position sensorAE – Rear port end cover with integrated priority and

shuttle valve [for 18cc AG pump only]

31 32 Paint00 – No paint0B – BlackCD – Blue primer

33 34 Identification/packaging01 – Standard Eaton identification box packaging

35 Design levelB – Second design

1 *Additional Settings Available by Request , including fixed displacement stops.2 # - Recommend RPC pressure settings 10-21 bar (140-350 psi)

1 2 3

AEC

4 5 6

028

7

R

8 9

05

10 11

AB

12

A

13

1

14 15

AA

16 17

28

18 19

20

20 21

00

22 23

00

24 25

01

26 27

00

28

1

29 30

00

31 32

CD

33 34

01

35

B


Specifications and performance220 Series Mobile Piston Pump

General performance specifications Units AEC018 AEC028

Displacement cc/r (in3/r) 18 (1.09) 28.0 (1.71)Mounting (SAE) 2 Bolt A 2 Bolt BPressure Continuous bar (psi) 280 (4060) 280 (4060)

Intermittent1 320 (4600) 320 (4600)Peak2 350 (5000) 350 (5000)

Speed3 At 1 bar abs (0 psig) rpm 3600 3000At .85 bar abs (5 in.Hg) 3000 2700Max (standby) 3900 3600Min 500 500

Power Max (theoretical) kW (hp) 30.15 (40.43) 39.2 (52.6)Standby 1.62 (2.17) 2.1 (2.8)

Torque Max (theoretical) Nm (lb-ft) 80 (59) 125 (92)Weight4 kg (lbm) 13.2 (29.1) 16.3 (35.9)Bearing life5 At 140 bar (2030 psi) B10 Hours 16,222 62,000

At 210 bar (3045 psi) 4,200 16,000At 280 bar (4060 psi) 1,610 5,850

Mass moment of inertia

Kg-m2 (lbm-ft2)

0.003 (0.075) 0.005 (0.119)

Hydraulic fluids

Fluid

Recommended operating viscosity range cSt (SUS)

Maximum continuous cSt (SUS)

Maximum viscosity at startup cSt (SUS)

Minimum viscosity @ max. Temperature of 93°C (200°F) cSt (SUS)

Minimum intermittent cSt (SUS)

Use antiwear hydraulic oil, or automotive type crankcase oil (designations SC, SD, SE or SF) per SAE J183 FEB80

16 to 40 (80 to 188) 430 (1192) 2100 (9720) 10 (59) 6 (46)

1 Less than 10% of duty cycle.2 Momentary system pressure spikes only.3 Ratings based on flange ports.4 Standard non-through drive pump.5 Bearing life ratings at rated speed – 1 bar abs (0 psig) inlet. Will vary based on thrust and side loads.

For more information, see Eaton publication 579. For operation on other alternative or environmentally friendly fluids, please contact your Eaton Representative.

Inlet pressure, case pressure, and operating temperature requirementsInlet pressure Case pressure Operating temperature

Rated Minimum MaximumMaximum continuous

Maximum intermittent Peak Rated

Minimum temperature

Maximum intermittent

bar abs (psig) bar abs (in. Hg) bar abs (psig) bar abs (psig) bar abs (psig) bar abs (psig) °C (°F) °C (°F) °C (°F)

1.0 (0) 0.85 (5) 4.4 (50) 1.3 (5) 3.1 (30) 6.2 (75) 93 (200) -37 (-35) 104 (220)


Control optionsPressure & Flow (Load Sense) Compensator for AEC018 AG variant only

The Agricultural tractor variant of 220 pump has a shuttle valve integral into pump end cover which senses the highest load of the two-work circuit and a priority valve to set the flow priority . For tractor application steering is given priority over other auxiliary functions like hitch circuit for implements .

Fluid output from the pump end cover enters into the priority valve before reaching to system . Integrated priority valve gives the pump flow priority to Steering system over the Hitch valve of the tractor . The shuttle valve senses highest of the two load pressures (Steering load or Hitch system load) and gives the load sense signal to flow control of the pump to adjust the pump flow as per the load requirement . The load signal is carried through steel pipe from end cover to pump controller .

These features make this pump suitable for other platforms where shuttle and priority valve are required .

Gage outlet

Gage inlet

Priority valve(PFRD)

Bleed down(Opt)(Opt)

(Opt)

Shuttle valveInlet

Steering LS signal

Auxiliary LS signal

Flow to steeringFlow to auxiliary


Dynamic response per SAE J745 (using swash plate position)

Response(off stroke)

Recovery(on stroke)

Load sense recovery

msec msec msec

AEC018 25 50 40AEC028 14 49 49

The pump will provide flow & pressure matching of pump output to system load demand, maximizing efficiency and improving load metering characteristics of any directional control valve installed between the pump and the load . Load sensing ensures that the pump always provides only the amount of flow needed by the load . The pump operating pressure adjusts to the load pressure plus a pressure differential required for the load sense margin . When the system is not demanding flow, the load sense control will operate in low pressure zero flow, energy saving stand-by mode . The differential pressure is the difference between the pressure inlet and service port of a proportionally controlled directional valve, or a load sensing directional control valve . See the model code for differential pressure settings for load sensing . If the load pressure exceeds the system pressure setting, the pressure compensator reduces pump displacement . The load sensing line must be as short as possible and can also be used for remote pressure control or unloading of the pump pressure . For remote pressure control purposes, it is recommended that you contact your Eaton Representative for the correct configuration of the control .

Warning:

• When adjusting the pressure limiter, install a 0 to 350 bar (0 to 5000 psi) gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement . It is possible to adjust the pressure compensator beyond the rated pressure of the pump . Doing so, may void the warranty of the pump .

• EATON recommends use of relief valve in all systems .

Pressure limit settings

The pressure compensator uses two springs to cover the full pressure range of the X20 pumps .

Spring 1 = < 140 bar (2050 psi)

Spring 2 = 145 - 280 bar (2100 - 4060 psi)

Flow Compensator (Load Sense) settings

There are two springs used to cover the load sense adjustment range of this control . Available load sense range is

Spring 1 = < 20 bar (290 psi)

Spring 2 = 21 - 42 bar (300-609 psi)

Gage outlet

Load sense

Bleed down(Opt)(Opt)

(Opt)

Gage inlet

Inlet

To load

Typical operating curve

Outlet Pressure

Ou

tlet

Flo

w

Q

P

Control optionsPressure & Flow (Load Sense) Compensator


Dynamic response per SAE J745 (using swash plate position)

Response (off stroke) Recovery (on stroke)

msec msec

AEC018 25 50AEC028 20 65

The pump will provide a con tinuously modulated flow to meet changing load demands at a pre-adjusted compensator pressure . At pressures below the compensator setting, the pump will operate at maximum displacement . See model code position #16, 17 for compensator pressure ranges .

Warning:




The pressure compensator uses two springs to cover the full pressure range of the X20 pumps .

Spring 1 = < 140 bar (2050 psi)

Spring 2 = 145 - 280 bar (2100 - 4060 psi)

310 bar (4496 psi for 74 cc pump)

“K” inlet gage port

“B” Inlet

“F” case drain

“C” Outlet

To load

“K” outlet gage port

+

+

Pressure cut-off characteristics of pressure compensator control @ 49°C (120°F), static conditions.

Outlet Pressure

Ou

tlet

Flo

w

Q

P

Control optionsPressure Compensator


Remote relief valve is to be connected to pilot port “J” through necessary external piping . Standard differential pressure of 20 bar is set at RPC spool . The required outlet pressure (below 280 bar) can be set by adjusting remote relief valve setting . Once pressure reaches preset value, flow across remote relief valve starts, this results in RPC spool movement due to pressure imbalance . This will de-stroke the pump to maintain the set pressure .

Secondary fixed pressure compensator is provided to limit the max pressure setting as a fail safe measure .

Note

• Flow Compensator is not available with RPC .• When selecting this option in the model code, a pressure

setting value must be identified in the flow compensator field . Select a range of 10-24 bar (140-350 psi), default is 20 . The setting selected is the RPC differential pressure .

• Remote relief valve is not included in supply scope of the pump .

Delta pressure setting at control valve - bar (psi) 14 - 24 (200 - 350)Control fluid consumption - lpm (gpm) 4.5 (1.2) max.Recommended flow rating of remote relief valve- lpm (gpm) 3 – 5 (0.8 – 1.32)Recommended Eaton Relief Valve part number RV5-10-S-0-50

Hys

tere

sis/

p

ress

ure

ris

e

Ou

tlet

pre

ssu

re

psi

(b

ar)

4800 (280)

290(20)

Flow - gpm (lpm) Qmax0

0

Gage outlet

Gage inlet

Inlet

To load

Remote relief valve not in Eaton supply scope

Control optionsRemote Pressure Control (RPC) for AEC028


Pump displacement can be controlled infinitely, as per the current signal provided to the solenoid control valve . The integrated pump control makes use of an external current signal to vary the pump displacement . This control has an proportional characteristic i .e . with increasing current signal, the displacement increases proportionately .

This control is with manual override . Based on fail safe condition there are two types:

Min type (EP): Return to min displacement in case of power loss . Max type (EPD): Return to max displacement in case of power loss

Warning:




The EDC can operate between 20 bar (290 psi) and 280 bar (4060 psi) .

Gage outlet

(Opt)

Load sense

Bleed down(Opt)

(Opt)

Gage inlet

Inlet

To load

Gage outlet

(Opt)

(Opt)

Load sense

Bleed down(Opt)

Gage inlet

Inlet

To Load

Electrical data

Voltage 12 V DC 24 V DCMax Current 1500 mA 750 mAR20, Resistance(ohm) 5.19 +/- 0.52% 20.8 +/- 2.08Type of Control Current CurrentRecommended 250 Hz 250 HzPWM FrequencyDither Frequency 75 Hz 75 HzDither Amplitude 300 mA 300 mADuty Cycle 100% 100%Insulation material Class H, 180 deg C Class H, 180 deg CProtection Class IP69K IP69KConnector Deutsch DeutschOperating Temperature -40 deg C; 85 deg C -40 deg C; 85 deg C

This control has manual override . Hysteresis less than 5% . For cold start function,Control type Supply current (mA)

12V 24VEP 0 0EPD 480 240

EPD type EP type

100

50

00 400

400

800

800 24V

Current (mA)

Dis

pla

cem

ent

(%)

1200

600

1600 12V

2000

100

50

0

0 400

400

800

800 24V

Current (mA)

Dis

pla

cem

ent

(%)

1200

600

1600 12V

2000

Control optionsElectronic Displacement Control (EDC) for ACE028


The EH Inverse Proportional Pressure control allows for stepless variation of the max pump output pressure, as per the current signal provided to the control valve solenoid .

The integrated pump control makes use of an external current signal to vary the pump output pressure

This control has an inverse proportional characteristic i .e . with increasing current signal, the max output pressure is proportionately reduced

Warning:




The minimum is 110 bar and max pressure can be set from 140 bar (2050 psi) to 280 bar (4060 psi) .

Typ. Current vs pressure characteristics of IPPC at 1800 rpm at various max pressure settings at 49 deg C (120deg F), static conditions.

0 100 200 300 400 500 600 700 8000

50

100

150

200

250

300

Current (mA)

Pre

ssu

re (

bar

)

Electrical data

Voltage 12 V 24 VMax Current 1500 mA 750 mAR20, Resistance (ohm) 5.3 +/- 5% 21.2 +/- 5%Type of Control Current CurrentRecommended 100 Hz 100 HzPWMFrequencyDuty Cycle 100% 100%Insulation material Class H, 180 deg C Class H, 180 deg CProtection Class IP6K6/IP69K IP6K6/IP69KConnector AMP Junior Power AMP Junior Power

Timer/ Deutsch Timer/ DeutschConnector DT04-2P Connector DT04-2P

Operating Temperature -30 deg C; 105 deg C -30 deg C; 105 deg C

Gage outlet

Gage inlet

Inlet

To load

Control optionsEH inverse proportional pressure control (IPPC) for AEC028


The Electronic Destroke Valve reduces pump start-up torque by directing outlet pressure to the control piston .

It is primarily used in cold weather applications and includes a 12 or 24 VDC directional control valve mounted between the pump housing and compensator .

Refer model code position 22,23 - control special features for available connector options

Gage outlet

Gage inlet

Inlet

To load

(Opt)

Load sense

Bleed down(Opt)

(Opt)

Control optionsElectronic Destroke (Cold Start) Valve


PerformanceAEC018

95.0%

90.0%

85.0%

80.0%

75.0%

70.0%0 500 1000 1500 2000 2500 3000 3500 4000

Input Speed (RPM)

Effi

cien

cy%

5

10

15

20

25

30

35

40

45

0 500 1000 1500 2000 2500 3000 3500 4000

Inp

ut

Po

wer

(h

p)

Input Speed (RPM)

35 bar (508 psi)

70 bar (1015 psi)

140 bar (2030 psi)

210 bar (3045 psi)

280 bar (4060 psi)

35 bar (508 psi)

280 bar (4060 psi)

70 bar (1015 psi)

210 bar (3045 psi)

140 bar (2030 psi)

Overall efficiency versus speed @ 49˚C (120˚F, full flow, and 1.0 bar (0 psi) Inlet

Input power versus speed @ 49ºC (120ºF), full flow, and 1.0 bar (0 psi) Inlet


PerformanceAEC018

0

100

200

300

400

500

600

700

800

900

0 500 1000 1500 2000 2500 3000 3500 4000

Inp

ut

To

rqu

e (l

b-in

)

Input Speed (RPM)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

18.0

0 500 1000 1500 2000 2500 3000 3500 4000

Inp

ut

To

rqu

e (l

b-i

n)

Input Speed (RPM)

Cas

e Fl

ow

(g

pm

)

280 bar (4060 psi)

210 bar (3045 psi)

140 bar (2030 psi)

70 bar (1015 psi)

35 bar (508 psi)

35 bar (507 psi)

280 bar (4060 psi)35 bar(507 psi)

280 bar (4060 psi)

Input Torque Versus Speed @ 49ºC (120ºF),Full Flow, and 1.0 bar (0 psi) Inlet

Delivery & Case Flow Versus Speed @ 49ºC (120ºF),Full Flow, and 1.0 bar (0 psi) Inlet


35 bar (507 psi)

70 bar (1015 psi)

140 bar (2030 psi)

210 bar (3045 psi)

280 bar (4060 psi)

70

72

74

76

78

80

82

84

86

88

90

0 500 1000 1500 2000 2500 3000 3500

Ef�

cien

cy (%

)

Input Speed (rpm)

35 bar (507 psi)

70 bar (1015 psi)

140 bar (2030 psi)

210 bar (3045 psi)

280 bar (4060 psi)

0

5

10

15

20

25

30

35

40

45

50

55

60

0 500 1000 1500 2000 2500 3000 3500

Inp

ut

Pow

er (

hp

)

Input Speed (rpm)

Input power versus speed @ 49ºC (120ºF), full flow, and 1.0 bar (0 psi) Inlet

PerformanceAEC028

Overall efficiency versus speed @ 49ºC (120ºF), full flow, and 1.0 bar (0 psi) Inlet


35 bar (507 psi)

70 bar (1015 psi)

140 bar (2030 psi)

210 bar (3045 psi)

280 bar (4060 psi)

0

250

500

750

1,000

1,250

1,500

0 500 1000 1500 2000 2500 3000 3500

Inp

ut

Torq

ue

(in

-lb

)

Input Speed (rpm)

35 bar (507 psi)

280 bar (4060 psi)

35 bar (507 psi)

280 bar (4060 psi)

0.0

1.0

2.0

3.0

4.0

5.0

0

5

10

15

20

25

0 500 1000 1500 2000 2500 3000 3500

Cas

e Fl

ow

(g

pm

)

Del

iver

y (g

pm

)

Input Speed (rpm)

Input torque versus speed @ 49ºC (120ºF), full flow, and 1.0 bar (0 psi) Inlet

Delivery and case flow versus speed @ 49ºC (120ºF)

PerformanceAEC028


Pump installationAEC018 A-Mount standard - side-ported

RH Rotation

28[1.10]

135.9[5.35]

72.4[2.85]

60[2.36]

60[2.36]

76[2.99]

130[5.118]

106.4[4.19]

62.5[2.46]Top case drain

Case drain vertical

11.2[.44]

2xØ

Ø82.5[3.25]

For compensatorconfigurationsee separatecompensatorinstallation drawing

60[2.36]

72.1[2.84]

60[2.36]

63[2.48]

37.8[1.49]

Pressure diagnostic port

Suction diagnostic

port

6.4[.25]

135.9[5.35]149.4

[5.88] 177.4[6.98]

Pressure port

21.4[.84]

36[1.42]

For shaft configurationsee saperate shaftinstallation drawing

Top case drain

151.4[5.96]

Suction port


RH Rotation

72.4[2.85]

21.4[.84]

135.9[5.35]

Top case drain

Case drain vertical

Load sense port[Steering]

28[1.10]

96[3.78]

4.2[.16]24

[.95]

2x

68.1[2.68]

35 [1.38]35 [1.38]

31[1.22]

5 [.20]

Suctionport

15°82.3[3.24]

39.7[1.56]

25[.98] 36

[1.42]

Pressure port

6.4[.25]

Ø82.5[3.25]

173.4[6.83]253.4

[9.98]

154.4[6.08]

125.6[4.95]

56.5[2.22]

138.1[5.44]

106.4[4.19]

76[2.99]

65.5[2.46]

2xØ11.2[.44]

197.4[7.77]202.4

[7.97]


Pressure port (hitch port)

Pressure port(Steering port)

Suction diagnostic port

21.3[.84]

4.2[.16]

99.2[3.91]

10[.39]

34.8[1.37]

Pump installationAEC018 A-Mount AG version - rear ported


Pump installationAEC028 B-Mount - rear-ported

For compensator con�guration see separate compensator installation drawing

Suction diagnostic port Top case drain85.4[3.36]

37.66[2.664] 30

[1.18]

72.54[2.856]

18.9[.74]

86.1[3.39]

50.6[1.99]

15.5[0.61]

13.8[.54]

2X Ø14.3 [.56]

73.75[2.904]

4[.16]

146 [5.75]174 [6.85]

4.4[.173]

144.5[5.69]

106.7[4.2]

65[2.56]

35.5[1.40]

37.5[1.48]

67[2.64]181

[7.13]

144.5[5.69]

71[2.80]

Ø101.6[4.00]

33.2[1.31]

4.4[1.17]

67 [2.64]

A

A

40[1.57]

Vertical case drain

Pressure port


Bottom case drain

Pressure port

Right side case drain

Suction port

Suction port

Approximate center of gravity

Left side case drain

69.3 [2.73][Top case drain]

63.25 [2.490][Bottom case drain]

For shaft con�guration see separate shaftinstallation drawing

RH Rotation

View A-A LH Rotation


Pump installationAEC028 B-Mount - side-ported

Suction diagnostic portTop case drain

Vertical case drain

For compensator con�guration see separate compensator installation drawing

Pressure port


Pressure port

Bottom case drain

Suction port

160.5[6.32]

4.4[.17]

67[2.64]

Right side case drain

Suction port



4 [.16]Left side case drain

69.25 [2.7][Top case drain]

40 [1.57]

85.4 [3.36]

138.54 [5.5] 72.54

[2.9]

18.86 [.74]144.5

[5.7]

50.6 [1.99]

80.5[3.2] 15.9

[.6]

13.8[.54]

146[5.75]

2 x Ø14.3[.6]

67[2.64]

186.5 [7.3]

144.5[5.69] 71

[2.8]9.4[.37]

Ø101.6 [4]

2X 13.4[.53]

33.2[1.31]

160.5 [6.32]

125.4 [4.94]

117.42[4.62]

74.12[2.9]

74.88[2.9]

106.71[4.2]

A

A

65 [2.6]

66 [2.6]

30[1.18]

63.3 [2.49][Bottom case drain]

For shaft con�guration see separate shaftinstallation drawing

View A-A LH Rotation

RH Rotation


Pump installationAEC028 Thru drive SAE-A

SAE-A mount

Output shaft installation AA- 9T spline

Max Torque 91 Nm (805 lbf-in)

Ø16.54 [.651] 9 tooth 30° flat root side fit 16/32 class 6 per ANSI B92.1-1996

Ø19.71 [.776] 11 tooth 30° flat root side fit 16/32 class 6 per ANSI B92.1-1996

Accepts 9 tooth 16/32 pitch flat root side fit involute spline per SAE J744-16-4

Accepts 11 tooth 16/32 pitch flat root side fit involute spline per SAE J744-16-4.

Additional unit driven by this spline must not require more than 91 Nm (805 lbf-in) of Torque

Additional unit driven by this spline must not require more than 172 Nm (1522 lbf-in) of Torque

Output shaft installation AB- 11T spline


EATON 220 MOBILE PISTON PUMP CATALOG E-PUOV-TP001-E8 March 2018 www.eaton.com15

106.4[4.2]

30°

30°

216[8.5]

2-Bolt SAE J744-82-2

Groove to acceptan AS 568A size152 O-ring

For output shaft

see separate shaftinstallation drawing

8X .375-16 UNC - 2B 15.0

32[1.26]

38[1.49]


146 [5.7] ø8x 0.50- 13 UNC 2B thru

For outputshaft con�gurationsee separate shaft installation drawing

Groove toaccept an AS 568A size 1525 O-ring

216[8.5]

30˚

30˚

41[1.61]

5.9 [.23]

56.3[2.22]

56.3

[2.

22]

32.5[1.28]

O-ringgroove

4 X Ø7.2 ±0.18 thru [.30]

7.5[.30]

81.5[3.21]

32.5 [1.28] 193 [7.60]

Pump installationAEC028 Thru drive SAE-B

Cover plate

Fits on 220-SAE “A” type auxiliary mounting end cover

Cover Plate Kit # 9901110-000; includes O-ring, Cover Plate, Cap Screws (2)

AC - 13T spline


Ø22.89 [0.90] 13 tooth 30° flat root side fit 16/32 class I internal spline per ANSI B92.1A-1976

Accepts 13 tooth 30° flat root side fit 16/32 external splines class 5 per ANSI B92.1A-1996

Additional units driven by this spline must not require more than 252 Nm (2230 lbf-in) of Torque

Thru drive cover plate information

AG - Auxiliary mount ready with cover plate


Control InstallationAEC018- Pressure & Flow (Load Sense) Compensator

64.5[2.54]

110.1[4.34]

94.7[3.73]

74.8[2.94]

63.5[2.50]

125.6[4.95] 85.1

[3.35]

Load sense port7/16-20 UNF-2B O-ring port


189.86[ 7.5 ]

74.79[ 2.9 ]

64.51[ 2.5 ]

117.42[ 4.6 ]

125.35[ 4.9 ]

132.94[ 5.2 ]

117.42[ 4.6 ]

68.8[ 2.7 ]

47.0 Min.1.85[ ]

93.13.66[ ]

67.42.65[ ]

107.34.22[ ]

Pressure Compensator Control

205.1 [8.07] Max186.4 [7.34] Min.

Control InstallationAEC-028 Pressure & Flow (Load Sense) Compensator


208.1[8.19]

96.8[3.81]

51.4[2.02]

77.3[3.04]

155.5[6.12]

Deutsch connector optionAmp connector option

43.51.71[ ]

136.15.36[ ]

132.45.21[ ]

229.1 EDC Length9.02[ ]

117.4

4.62[ ]

48.91.92[ ]

Manualoverride

Load sense port

DeutschConnector

EH Inverse Proportional Pressure Control (IPPC)

68.32.69[ ]

122.44.82[ ]

186.9

7.36[ ]

Control InstallationACE028- Electronic Displacement Control (EDC)


AEC028 Maximum Stroke Limiter

28.16[1.1]

82.36[3.2]

133.14[5.2]

Max displacement

Torque 27+2.7 NMAfter adjustingdisplacement

Max displacement is reducedby approximately 6% to 7%per clockwise turn

Compensator/Controlnot shown for clarity

20°

Max Displacement is reducedby approximately 7 to 8%per clockwise turn

Compensator/Control not shown for clarity

90.0[3.54]

20˚

143.5[5.65]

Max Displacement

12.0[.47]

60% of Max Displacement

6.4[.25]

External Manual Stroke AdjustmentAEC018 Maximum Stroke Limiter


Cold start valveAEC018 Cold start valve

AEC028 Cold start valve

153.6[6.05]

20.8[.82]

49.9[1.96]

69.1[2.72]

62.1[2.44]

33.1[1.31]

118.9[4.68] 101.65

[4.002]

133.1[5.24]

153.7[6.05]

126.2[4.97]

108.9[4.29]

33.1[1.31]

51.4[2.02]

74.4[2.93]

67.4[2.65]

140.4[5.53]

49.9[1.96]

Deutsch option Metri - pack 280 option Metri - pack 150 option DIN 43650 - A option

Flying lead coil shownsee belowfor options


05 CodeMaximum Torque209.3 Nm [1852 in-lbf]

Key width6.3

+0.04

-0.04

.248+.001

-.001[ ]

411.61[ ]

22.18+0.03

-0.03

.873+.001

-.001[ ]

24.9.980[ ]

3.1.12[ ]

24.6.97[ ]

41.1[1.62]

Ø21.737 (.8558) 13 Tooth 30ºFlat Root Side Fit16/32 Class 5 Spline

Fits 13 tooth 30º Flat RootSide Fit 16/32 InternalSplines per SAE J498bClass 1 or ANSI B92.1 Class 5



461.81[ ]

25.38 +0.03-0.03

.999+.001-.001[ ]

28.141.108[ ]

3.9.15[ ]

28.61.13[ ]

Key width

6.3+0.04-0.04

.248+.001-.001[ ]


Ø 24.912 (.9808) 15 Tooth 30ºFlat Root Side Fit16/32 Class 5 Spline

Fits 15 tooth 30º Flat RootSide Fit 16/32 InternalSplines per SAE J498bClass 1 or ANSI B92.1 Class 5

461.81[ ]

Input shaft options


51 CodeMaximum Torque134 Nm [1186 in-lbf]

48 CodeMaximum Torque134 Nm [1186 in-lbf]

49 Code (for AG Variant only)Maximum Torque100 N-m [885 in-lbf]

38[1.50]

39.7[1.56]

22.2[.87]

11.27[.444]

Ø 19.05 (0.75) 11 tooth 30˚Flat root side fit16/32 Class 5 Splineper ANSI B92.1 (Modified)Fits 11 tooth 30˚ Flat RootSide Fit 16/32 InternalSplines Per SAE J498BClass 1 or ANSI B92.1 Class 5 Splines

9.8[.38]

6.37[.251]

Taper 1:8 On DIA.INC. Angle 7.116/7.1833

.437-20 UNF -2A THD’SMin. Full THD’S- .334Leave THD’S Soft Rc 35 to 42

16.002+0.12[.6300+.004]

Ø

50 CodeMaximum Torque100 N-m [885 in-lbf]

32[1.26]

21.5[.85]

21.1[.83]

2[.08]

Ø 15.8 (0.62) 9 tooth 30˚Flat Root Side Fit16/32 Class 5 Splineper ANSI B92.1 (Modified)Fits 9 Tooth 30˚ Flat RootSide Fit 16/32 InternalSplines per SAE J498BClass 1 or ANSI B92.1 Class 5 splines

19.035+0.015[.7494+.0005]

Ø

15.865+0.015[.6246+.0005]

Ø

Square key x4.76

+0.030

.188+.001-.000

14.27+0.25[.562+.009]

52 CodeMaximum Torque100 N-m [885 in-lbf]

32[1.26]

21.5[.85]

17.5[.69]

2[.08]

Square key x3.962

+0.030

.1560+.001-.000

14.27+0.25[.562+.009]

Input shaft options


Installation and start-up

Warning: Care should be taken that mechanical and hydraulic resonances are avoided in the application of the pump . Such resonances can seriously compromise the life and/or safe operation of the pump .

Drive data

Mounting attitude should be horizontal (shaft parallel to the ground) using the appropriate case drain port (furthest from the ground) to ensure that the case remains full of fluid at all times . If mounted with shaft upward (shaft perpendicular to the ground) the shaft end case drain (option G or H) must be used .

In those cases where geometric tolerances of mounting are critical, or where specific tolerance ranges are required and not specified, consult Eaton Engineering for specific limits .

Direction of shaft rotation, viewed from the prime mover end, must be as indicated in the model designation on the pump– either right hand (clockwise) or left hand (counterclockwise) .

Direct coaxial drive through a flexible coupling is recommended . If drives imposing radial shaft loads are considered, please consult your Eaton Representative .

Start-up procedure

Make sure the reservoir and circuit are clean and free of dirt/debris prior to filling with hydraulic fluid .

Fill the reservoir with filtered oil and fill to a level sufficient enough to prevent vortexing at the suction connection to pump inlet . It is good practice to clean the system by flushing and filtering, using an external slave pump .

Caution: Before the pump is started, fill the case through the uppermost drain port with hydraulic fluid of the type to be used . The case drain line must be connected directly to the reservoir and must terminate below the oil level .

Once the pump is started, it should prime within a few seconds . If the pump does not prime, check to make sure that there are no restrictions between the reservoir and the inlet to the pump, and that the pump is being rotated in the proper direction, and that there are no air leaks in the inlet line and connections . Also check to make sure that trapped air can escape at the pump outlet .

After the pump is primed, tighten the loose outlet con nections, then operate for five to ten minutes (unloaded) to remove all trapped air from the circuit .

If the reservoir has a sight gage, make sure the fluid is clear– not milky .

Fluid cleanliness

The X20 Series pumps are rated in anti-wear petroleum fluids with a contamination level of 21/18/13 per ISO 4406 . Operation in fluids with levels more contaminateda than this is not recommended . Fluids other than petroleum, severe service cycles, or temperature extremes are cause for adjustment of these codes . Please contact your Eaton Representative for specific duty cycle recommendation .

Eaton X20 Series pumps, as with any variable displacement piston pumps, will operate with apparent satisfaction in fluids up to the rating specified here . Experience has shown however, that pump and hydraulic system life is not optimized with high fluid contamination levels (high ISO cleanliness codes) .

Proper fluid condition is essential for long and satisfac tory life of hydraulic components and systems . Hydraulic fluid must have the correct balance of cleanliness, materials, and additives for protection against wear of components, elevated viscosity and inclusion of air .

Essential information on the correct methods for treating hydraulic fluid is included in Eaton publication 561 – “Eaton Guide to Systemic Contamination Control” – available from your local Eaton distributor . In this publication, filtration and cleanliness levels for extending the life of axial piston pumps and other system components are listed . Included is an excellent discussion of the selection of products needed to control fluid condition .

EatonHydraulics Group USA14615 Lone Oak RoadEden Prairie, MN 55344USATel: 952-937-9800Fax: 952-294-7722www.eaton.com/hydraulics

EatonHydraulics Group EuropeRoute de la Longeraie 71110 MorgesSwitzerlandTel: +41 (0) 21 811 4600Fax: +41 (0) 21 811 4601

EatonHydraulics Group Asia PacificEaton BuildingNo.7 Lane 280 Linhong RoadChangning District, Shanghai200335 ChinaTel: (+86 21) 5200 0099Fax: (+86 21) 2230 7240

Eaton is a registered trademark.

All other trademarks are property of their respective owners.

Eaton1000 Eaton BoulevardCleveland, OH 44122United StatesEaton .com

© 2019 EatonAll Rights ReservedPrinted in USADocument No . E-PUOV-TP001-E8 / 4149Supersedes E-PUOV-TP001-E7August 2019

220 mobile piston pump catalog design code b

Documents