20212021 owner’s manual · 1983. 1. 1. · turns, drop-offs, rocks, ruts and other hazards....
TRANSCRIPT
20212021 CRF300L/LA
Owner’s Manual
This manual should be considered a permanent part of the vehicleand should remain with the vehicle when it is resold.
This publication includes the latest production information availablebefore printing. Honda Motor Co., Ltd. reserves the right to makechanges at any time without notice and without incurring anyobligation.
No part of this publication may be reproduced without writtenpermission.
The vehicle pictured in this owner’s manual may not match youractual vehicle.
© 2020 Honda Motor Co., Ltd.
WelcomeCongratulations on your purchase of a newHonda vehicle. Your selection of a Hondamakes you part of a worldwide family ofsatisfied customers who appreciate Honda'sreputation for building quality into everyproduct.
To ensure your safety and riding pleasure:● Read this owner's manual carefully.● Follow all recommendations and
procedures contained in this manual.● Pay close attention to safety messages
contained in this manual and on thevehicle.
To protect your investment, we urge you totake responsibility for keeping your vehiclewell serviced and maintained. Also, observethe break-in guidelines, and always performthe pre-ride inspection and other periodicchecks in this manual.
When service is required, remember thatyour Honda dealer knows your vehicle best.If you have the required mechanical “know-how” and tools, you can purchase an officialHonda Service Manual to help you performmany maintenance and repair tasks. 2 P. 124Read the warranty information thoroughly sothat you understand the warranty coverageand that you are aware of your rights andresponsibilities. 2 P. 125You may also want to visit our website atwww.powersports.honda.com.Canada www.honda.ca.Happy riding!
A Few Words About SafetyYour safety, and the safety of others, is veryimportant. Operating this vehicle safely is animportant responsibility.To help you make informed decisions aboutsafety, we have provided operatingprocedures and other information on safetylabels and in this manual. This informationalerts you to potential hazards that couldhurt you or others.Of course, it is not practical or possible towarn you about all hazards associated withoperating or maintaining a vehicle. You mustuse your own good judgment.
You will find important safety information in avariety of forms, including:● Safety labels on the vehicle● Safety Messages preceded by a safety alert
symbol and one of three signal words:DANGER, WARNING, or CAUTION.These signal words mean:
3DANGERYou WILL be KILLED or SERIOUSLYHURT if you don’t follow instructions.
3WARNINGYou CAN be KILLED or SERIOUSLYHURT if you don’t follow instructions.
3CAUTIONYou CAN be HURT if you don’t followinstructions.
Other important information isprovided under the following titles:
NOTICE Information to help you avoiddamage to your vehicle, otherproperty, or the environment.
Contents
Vehicle Safety P. 2
Operation Guide P. 18
Maintenance P. 52
Troubleshooting P. 94
Information P. 108
Specifications P. 132
Safety Guidelines .................................................P. 3Safety Labels.........................................................P. 7Safety Precautions...............................................P. 9Riding Precautions ............................................P. 11Accessories & Modifications...........................P. 15Off-Road Safety .................................................P. 16Loading ................................................................P. 17
This section contains important information for safe riding of your vehicle.Please read this section carefully.
Vehicle Safety
Safety GuidelinesFollow these guidelines to enhance your safety:● Perform all routine and regular inspections
specified in this manual.● Stop the engine and keep sparks and flame
away before filling the fuel tank.● Do not run the engine in enclosed or partly
enclosed areas. Carbon monoxide inexhaust gases is toxic and can kill you.
Always Wear a HelmetIt's a proven fact: helmets and protectiveapparel significantly reduce the number andseverity of head and other injuries. So alwayswear an approved helmet and protectiveapparel. 2 P. 9
Before RidingMake sure that you are physically fit, mentallyfocused and free of alcohol and drugs. Checkthat you and your passenger are both wearingan approved helmet and protective apparel.Instruct your passenger on holding onto theseat strap or your waist, leaning with you inturns, and keeping their feet on the footpegs,even when the vehicle is stopped.
Take Time to Learn & PracticeEven if you have ridden other vehicles, practiceriding in a safe area to become familiar withhow this vehicle works and handles, and tobecome accustomed to the vehicle's size andweight.We recommend that all riders take a certifiedcourse approved by the Motorcycle SafetyFoundation (MSF) or a state approved trainingcourse. New riders should start with the basiccourse, and even experienced riders will find theadvanced course beneficial.
Safety GuidelinesVehicle Safety
3Continued
For information about the MSF training coursenearest you, call the national toll-free number:(800) 446-9227.
USA Other riding tips can be found in the Youand Your Motorcycle Riding Tips booklet thatcame with your vehicle.Developing off-road riding skill is a gradualstep-by step process. Start by practicing at lowspeeds in a safe area and slowly build yourskills.Ask your dealer if there are off-road ridinggroups in your area where you can learn fromexperienced riders. Also be sure to read Tips &Practice Guide for the Off-Highway Motorcyclistthat came with your new vehicle.
Ride DefensivelyAlways pay attention to other vehicles aroundyou, and do not assume that other drivers seeyou. Be prepared to stop quickly or perform anevasive maneuver.
Make Yourself Easy to SeeMake yourself more visible, especially at night,by wearing bright reflective clothing, positioningyourself so other drivers can see you, signalingbefore turning or changing lanes, and usingyour horn when necessary.
Be Alert for Off-road HazardsThe terrain can be present a variety ofchallenges when you ride off-road.Continually “read” the terrain for unexpectedturns, drop-offs, rocks, ruts and other hazards.Always keep your speed low enough to allowtime to see and react to hazards.
Ride within Your LimitsNever ride beyond your personal abilities orfaster than conditions warrant. Fatigue andinattention can impair your ability to use goodjudgment and ride safely.
Safety Guidelines
Vehicle Safety
4
Don't Drink or Use Drugs and RideAlcohol or drugs and riding don't mix. Even onealcoholic drink can reduce your ability torespond to changing conditions, and yourreaction time gets worse with every additionaldrink. The same is true for drug use. Don't drinkor use and ride, and don't let your friends do iteither.
Keep Your Honda in Safe ConditionIt's important to keep your vehicle properlymaintained and in safe riding condition.Having a breakdown can be difficult, especiallyif you are stranded off-road far from your base.Inspect your vehicle before every ride andperform all recommended maintenance. Neverexceed load limits (2 P. 17), and do not modifyyour vehicle or install accessories that wouldmake your vehicle unsafe (2 P. 15).
If You are Involved in a CrashPersonal safety is your first priority. If you oranyone else has been injured, take time toassess the severity of the injuries and whether itis safe to continue riding. Call for emergencyassistance if needed. Also follow applicable lawsand regulations if another person or vehicle isinvolved in the crash.
If you decide to continue riding, first turn theignition switch to the OFF position, and evaluatethe condition of your vehicle. Inspect for fluidleaks, check the tightness of critical nuts andbolts, and check the handlebar, control levers,brakes, and wheels. Ride slowly and cautiously.
Your vehicle may have suffered damage that isnot immediately apparent. Have your vehiclethoroughly checked at a qualified service facilityas soon as possible.
Safety GuidelinesVehicle Safety
5Continued
Carbon Monoxide HazardExhaust contains poisonous carbon monoxide, acolorless, odorless gas. Breathing carbonmonoxide can cause loss of consciousness andmay lead to death.
If you run the engine in confined or even partlyenclosed area, the air you breathe couldcontain a dangerous amount of carbonmonoxide.Never run your vehicle inside a garage or otherenclosure.
3WARNINGRunning the engine of your vehiclewhile in an enclosed or even partiallyenclosed area can cause a rapid build-up of toxic carbon monoxide gas.
Breathing this colorless, odorless gascan quickly cause unconsciousness andlead to death.
Only run your vehicle's engine when itis located in a well ventilated areaoutdoors.
Safety Guidelines
Vehicle Safety
6
Safety LabelsSafety and information labels on your vehicleprovide important safety information and maywarn you of potential hazards that could cause
serious injury. Read these labels carefully anddon't remove them.If a label comes off or becomes hard to read,contact your dealer for a replacement.
Safety LabelsVehicle Safety
7Continued
Safety Labels
Vehicle Safety
8
50 STATE (meets California)
Canada
Safety Precautions● Ride cautiously and keep your hands on the
handlebar and feet on the footpegs.● Keep passenger's hands onto the seat strap
or your waist, passenger's feet on thefootpegs while riding.
● Always consider the safety of yourpassenger, as well as other drivers andriders.
Protective ApparelMake sure that you and any passenger arewearing an approved helmet, eye protection,and high-visibility protective clothing. Avoidwearing loose clothes that could get caught onany part of the vehicle. Ride defensively inresponse to weather and road conditions.
# HelmetShould be safety-standard certified, high-visibility, and correct size for your head● Must fit comfortably but securely, with the
chin strap fastened.● Face shield with unobstructed field of vision
or other approved eye protectionUSA Look for a DOT (Department ofTransportation) certification label on any helmetyou buy.
3WARNINGNot wearing a helmet increases thechance of serious injury or death in acrash.
Make sure that you and any passengeralways wear an approved helmet andprotective apparel.
Safety PrecautionsVehicle Safety
9Continued
# GlovesFull-finger leather gloves with high abrasionresistance
# Boots or Riding ShoesSturdy boots with non-slip soles and ankleprotection
# Jacket and PantsProtective, highly visible, long-sleeved jacketand durable long pants for riding (or aprotective suit)
# Additional Off-road GearOn-road apparel may also be suitable for casualoff-road riding. But if you plan on any seriousoff-road riding you will need more serious off-road gear. In addition to your helmet and eyeprotection, we recommend off-road motorcycleboots and gloves, riding pants with knee andhip pads, a jersey with elbow pads, and a chest/shoulder protector.
Safety Precautions
Vehicle Safety
10
Riding PrecautionsBreak-in Period
During the first 300 miles (500 km) of running,follow these guidelines to ensure your vehicle'sfuture reliability and performance.● Avoid full-throttle starts and rapid
acceleration.● Avoid hard braking and rapid down-shifts.● Ride conservatively.
BrakesObserve the following guidelines:● Avoid excessively hard braking and
downshifting.u Sudden braking can reduce the vehicle's
stability.u Where possible, reduce speed before
turning; otherwise you risk sliding out.
● Exercise caution on low traction surfaces.u The tires slip more easily on such
surfaces and braking distances arelonger.
● Avoid continuous braking.u Repeated braking, such as when
descending long, steep slopes canseriously overheat the brakes, reducingtheir effectiveness. Use engine brakingwith intermittent use of the brakes toreduce speed.
● For full braking effectiveness, operate boththe front and rear brakes together.
Riding PrecautionsVehicle Safety
11Continued
# Anti-lock Brake System (ABS)CRF300LAThis model is equipped with an Anti-lock BrakeSystem (ABS) designed to help prevent thebrakes from locking up during hard braking.● ABS does not reduce braking distance. In
certain circumstances, ABS may result in alonger stopping distance.
● ABS does not function at speeds below 6mph (10 km/h).
● The brake lever and pedal may recoil slightlywhen applying the brakes. This is normal.
● Always use the recommended front/reartires and sprockets to ensure correct ABSoperation.
# Engine BrakingEngine braking helps slow your vehicle downwhen you release the throttle. For furtherslowing action, downshift to a lower gear. Useengine braking with intermittent use of thebrakes to reduce speed when descending long,steep slopes.
# Wet or Rainy ConditionsRoad surfaces are slippery when wet, and wetbrakes further reduce braking efficiency.Exercise extra caution when braking in wetconditions.If the brakes get wet, apply the brakes whileriding at low speed to help them dry.
Riding Precautions
Vehicle Safety
12
Parking● Park on a firm, level surface.● If you must park on a slight incline or loose
surface, park so that the vehicle cannotmove or fall over.
● Make sure that high-temperature partscannot come into contact with flammablematerials.
● Do not touch the engine, muffler, brakesand other high-temperature parts until theycool down.
● To reduce the likelihood of theft, always lockthe handlebar and remove the key whenleaving the vehicle unattended.Use of an anti-theft device is alsorecommended.
# Parking with the Side Stand1. Stop the engine.2. Push the side stand down.3. Slowly lean the vehicle to the left until its
weight rests on the side stand.4. Turn the handlebar fully to the left.
u Turning the handlebar to the rightreduces stability and may cause thevehicle to fall.
5. Turn the ignition switch to the LOCKposition and remove the key. 2 P. 44
Riding PrecautionsVehicle Safety
13Continued
Refueling and Fuel GuidelinesFollow these guidelines to protect the engine,fuel system and catalytic converter:● Use only unleaded gasoline.● Use recommended octane number. Using
lower octane gasoline will result indecreased engine performance.
● Do not use fuels containing a highconcentration of alcohol. 2 P. 123
● Do not use stale or contaminated gasolineor an oil/gasoline mixture.
● Avoid getting dirt or water in the fuel tank.
Riding Precautions
Vehicle Safety
14
Accessories &ModificationsWe strongly advise that you do not add anyaccessories that were not specifically designedor approved for your vehicle by Honda or makemodifications to your vehicle from its originaldesign. Doing so can make it unsafe.Modifying your vehicle may also void yourwarranty and make your vehicle illegal tooperate on public roads. Before deciding toinstall accessories on your vehicle, be certainthe modification is safe and legal.
3WARNINGImproper accessories or modificationscan cause a crash in which you can beseriously hurt or killed.
Follow all instructions in this owner'smanual regarding accessories andmodifications.
Do not pull a trailer with, or attach a sidecar to,your vehicle. Your vehicle was not designed forthese attachments, and their use can seriouslyimpair your vehicle's handling.
Accessories & ModificationsVehicle Safety
15
Off-Road SafetyLearn to ride in an uncongested off-road areafree of obstacles before venturing ontounfamiliar terrain.● Always obey local off-road riding laws and
regulations.● Obtain permission to ride on private
property. Avoid posted areas and obey “NOTrespassing” signs.
● Ride with a friend on another vehicle so thatyou can assist each other in case of trouble.
● Familiarity with your vehicle is criticallyimportant should a problem occur far fromhelp.
● Never ride beyond your ability andexperience or faster than conditions warrant.
● If you are not familiar with the terrain, ridecautiously. Hidden rocks, holes, or ravinescould spell disaster.
● A muffler is required in most off-road areas.Don't modify your exhaust system.Remember that excessive noise botherseveryone and creates a bad image formotorcycling.
Off-Road Safety
Vehicle Safety
16
Loading● Carrying extra weight affects your vehicle's
handling, braking and stability.Always ride at a safe speed for the load youare carrying.
● Avoid carrying an excessive load and keepwithin specified load limits.Maximum weight capacity 2 P. 132
● Tie all luggage securely, evenly balancedand close to the center of the vehicle.
● Do not place objects near the lights or themuffler.
Also follow these guidelines when you ride off-road on rough terrain:● Do not carry a passenger.● Keep cargo small and light weight.
Make sure it cannot easily be caught onbrush or other objects, and that it does notinterfere with your ability to shift position tomaintain balance and stability.
3WARNINGOverloading or improper loading cancause a crash and you can be seriouslyhurt or killed.
Follow all load limits and other loadingguidelines in this manual.
LoadingVehicle Safety
17
Parts Location
Operation Guide
18
Spark arrester(P.77)
Seat (P.74)
Fuse box A (P.104)
Engine oil level inspectionwindow (P.79)
Engine oil fill cap (P.79)
Rear brake fluid reservoir(P.83)
Throttle grip (P.93)
Right side cover (P.76)
Operation Guide
19
Left shroud(P.75)
Front brake fluid reservoir (P.83)Fuel fill cap (P.49)
Clutch lever (P.90)Coolant reserve tank (P.81)
Helmet holder (P.50)
Tool box/Tool kit (P.51)Document bag (P.51)
Left side cover (P.76)
Main fuse (P.105)Battery (P.72)
Shift lever (P.48)Side stand (P.86)Drive chain (P.87)
Fuse box B (P.106)CRF300LA
Instruments
Operation Guide
20
TachometerNOTICEDo not operate the engine in the tachometer red zone.Excessive engine speed can adversely affect engine life.
Tachometer red zone(excessive engine rpm range)
SET button
Display CheckWhen the ignition switch is turned to the ON position, all the mode and digitalsegments will show. If any part of these displays does not come on when it should,have your dealer check for problems.
SEL button
Operation Guide
21Continued
Remaining fuel when only 1st (E) segment starts flashing:approximately 0.50 US gal (1.9 L)
Fuel gauge
If the fuel gauge indicator flashes in a repeat pattern or turns off:(P.98)
Clock (12-hour display)
Speedometer
Gear position indicatorThe gear position is shown in the gearposition indicator.u “-” appears when the transmission is
not shifted properly.
To set the clock: (P.30)
Average fuel mileage [AVG] , Fuel consumption andAverage speed [AVG] (P.26)
Odometer [TOTAL] & Tripmeter[TRIP A/B] & Stopwatch (P.22)
Odometer [TOTAL] & Tripmeter [TRIP A/B] & StopwatchThe SEL button switches between the odometer, tripmeter A, tripmeter B, and stopwatch.
Operation Guide
22
Instruments (Continued)
Odometer Tripmeter A Tripmeter B Stopwatch
# Odometer [TOTAL]Total distance ridden. When “------” isdisplayed, go to your dealer for service.
# Tripmeter [TRIP A/B]Distance ridden since tripmeter was reset.When “----.-” is displayed, go to your dealerfor service.To reset the tripmeter: (P.24)
# StopwatchShows elapsed time since the SET buttonwas pushed to start the measurement.Display range:0H00M00.0S - 9H59M59.9S• Above 9H59M59.9S back to 0H00M00.0S
To use the stopwatch: (P.25)
Operation Guide
23Continued
# To reset the tripmeter [TRIP A/B],average fuel mileage [AVG], fuelconsumption and average speed [AVG]
To reset the tripmeter A, average fuelmileage A, fuel consumption A and averagespeed A (these are based on tripmeter A)together, press and hold the SEL buttonwhile tripmeter A is displayed.
To reset the tripmeter B, average fuelmileage B, fuel consumption B and averagespeed B (these are based on tripmeter B)together, press and hold the SEL buttonwhile tripmeter B is displayed.
Operation Guide
24
Instruments (Continued)
Average fuelmileage A
or or
Fuelconsumption A
Averagespeed A
Tripmeter A
oror
Average fuelmileage B
or or
Fuelconsumption B
Averagespeed B
Tripmeter B
oror
Stopwatch
# To Measure the Time1. Select the stopwatch. (P.22)2. To start measurement, press the SET
button.u The measurement keeps going, if you
change an item while measuring.3. To finish measurement, press the SET
button.u The measurement can also be finished
by turning the ignition switch to theOFF position.
# To Restart the MeasurementPress the SET button again. The stopwatchrestarts measurement.
# To Reset the Measured valuePress and hold the SEL button when thestopwatch is displayed and also themeasurement is finished.
Operation Guide
25Continued
StopwatchSET button
SEL button
Average fuel mileage [AVG] , Fuel consumption and Average speed [AVG]The SET button switches between the average fuel mileage, fuel consumption, and averagespeed.Operation Guide
26
Instruments (Continued)
Average fuel mileage Fuel consumption Average speed
# Average fuel mileage [AVG]Displays the average fuel mileage since theselected tripmeter was reset.The average fuel mileage will be calculatedbased on value displayed on the tripmeter (Aor B) selected.Also, the average fuel mileage for tripmeterA will be displayed when the odometer,tripmeter A, and stopwatch are selected.Display range:50 STATE (meets California) 0.0 to 299.9mile/gal (km/L or L/100km)Canada 0.0 to 299.9 km/L (L/100km, mile/galor mile/L)• More than 299.9 : “299.9” is displayed.• When the tripmeter A or B is reset: “---.-”
is displayed.
When “---.-” is displayed except for theabove-mentioned cases, go to your dealerfor service.To reset the average fuel mileage:(P.24)
Operation Guide
27Continued
# Fuel consumptionDisplays the fuel consumption since theselected tripmeter was reset.The fuel consumption will be calculatedbased on value displayed on the tripmeter (Aor B) selected.Also, the fuel consumption for tripmeter Awill be displayed when the odometer,tripmeter A, and stopwatch are selected.Display range:0.0 to 299.9 gal (gallon) or 0.0 to 299.9 L(liters)• More than 299.9 : “299.9” is displayed.
When “---.-” is displayed, go to your dealerfor service.To reset the fuel consumption: (P.24)
# Average speed [AVG]Displays the average speed since the selectedtripmeter was reset.The average speed will be calculated based onvalue displayed on the tripmeter (A or B)selected.Also, the average speed for tripmeter A will bedisplayed when the odometer, tripmeter A, andstopwatch are selected.Display range:0 to 124 mile/h (0 to 199 km/h)• Initial display: “---” is displayed.• When your vehicle has traveled less than
0.12 mile (0.2 km) since the engine wasstarted: “---” is displayed.
• When your vehicle operating time is lessthan 30 seconds since the engine wasstarted: “---” is displayed.
When “---” is displayed except for the above-mentioned cases, go to your dealer for service.To reset the average speed: (P.24)
Operation Guide
28
Instruments (Continued)
Display SettingSetting Mode AFollowing items can be changed sequentially. (P.30)• Clock setting• Backlight brightness adjustment• Changing the speed and mileage unit• Changing the fuel mileage meter unit
Setting Mode BFollowing items can be changed sequentially. (P.33)• Setting of REV indicator
(lighting RPM setting, lighting interval RPM setting and brightness adjustment)• Setting display mode of tachometer
Operation Guide
29Continued
Setting Mode AIf the SET button is not pressed for about 30seconds, the control is automatically switchedfrom the setting mode to the ordinarydisplay.
If the SET button is not pressed for about 30seconds, items in the process of being set willbe discarded and only items where settingshave been finalised will be applied. Only ifthe ignition switch is turned to the OFFposition will items in the process of being setand those that are finalised be applied.
1 Clock setting:a Turn the ignition switch to the ON position.b Press and hold the SEL and the SET
buttons until the hour digits start flashing.
c Press the SEL button until the desired houris displayed.u Press and hold the SEL button to
advance the hour fast.
d Press the SET button. The minute digitsstart flashing.
Operation Guide
30
Instruments (Continued)
e Press the SEL button until the desiredminute is displayed.u Press and hold the SEL button to
advance the minute fast.
f Press the SET button. The clock is set, andthen the display moves to the backlightbrightness adjustment.
2 Backlight brightness adjustment:You can adjust the brightness to one of fivelevels.a Press SEL button. The brightness is
switched.
b Press SET button. The backlight is set, andthen the display moves to the changing thespeed and mileage unit.
Operation Guide
31Continued
3 Changing the speed and mileage unit:a Press SEL button to select either "mph" and
"mile" or "km/h" and "km".
b Press SET button. The speed and mileageunit is set, and then the display moves to thechanging the fuel mileage meter unit.
4 Changing the fuel mileage meter unit:a When the “km/h” for speed and “km” for
mileage are selectedPress SEL button to select “L/100km” or“km/L”.Canada onlyWhen the “mph” for speed and “mile” formileage are selectedPress SEL button to select “mile/L” or“mile/gal”.u When "mile/gal" is selected, the unit of
the fuel consumption is changed to "gal".b Press SET button. The fuel mileage meter
unit is set, and then the display moves to theordinary display.
Operation Guide
32
Instruments (Continued)
Setting Mode BIf the SET button is not pressed for about 30seconds, the control is automatically switchedfrom the setting mode to the ordinarydisplay.
If the SET button is not pressed for about 30seconds, items in the process of being set willbe discarded and only items where settingshave been finalised will be applied. Only ifthe ignition switch is turned to the OFFposition will items in the process of being setand those that are finalised be applied.
1 Setting of REV indicator:You can change the setting of the REVindicator.REV indicator is blinking while setting.
Operation Guide
33Continued
Numericaltachometer display
SET button
SEL button
Tachometer
REV indicator
a To change the setting mode B, turn theignition switch to the ON position whilepressing SEL button until the display checkis finished. The blinking of bar segment inthe tachometer shows the currently appliedREV indicator lighting RPM, and thenumerical tachometer display shows it.u Tachometer bar segment is displayed as
conventional display, regardless of set updisplay method.
b Each time SEL button is pressed, thelighting RPM set value increase by250 r/min (rpm) (one segment). When theset value exceeds the allowable range, theRPM set value automatically returns to4,000 r/min (rpm).u Press and hold the SEL button to
advance the REV indicator lightingsetting value fast.
Available Setting Range4,000 r/min (rpm) -to- 10,500 r/min (rpm)
Operation Guide
34
Instruments (Continued)
c Press SET button. The REV indicator lightingRPM is set, and then the display moves tothe setting of REV indicator lighting intervalRPM.At the same time, the blinking barsegment shows the currently appliedsetting originated from the REV indicatorlighting RPM and the numericaltachometer display shows the REVindicator lighting interval RPM.
d Each time SEL button is pressed, thenumber of REV indicator lighting intervalRPM is switched among 0 r/min (rpm),250 r/min (rpm) and 500 r/min (rpm) in thisorder.
Operation Guide
35Continued
Numerical tachometerdisplay
Tachometer
Ex When REV indicator lighting RPM issetting 8,000 r/min (rpm) and REVindicator lighting interval RPM is250 r/min (rpm).REV indicator r/min (rpm)
Blinking(2 times/second) 7,250 r/min (rpm)
Blinking(5 times/second) 7,500 r/min (rpm)
Blinking(10 times/second) 7,750 r/min (rpm)
Lighting 8,000 r/min (rpm)
If the REV indicator lighting interval RPM is 0,the REV indicator starts to lighting whenreaching to the REV indicator lighting RPM.
e Press SET button. The REV indicator lightinginterval RPM is set, and then the displaymoves to the brightness adjustment of theREV indicator.The REV indicator switches from blinkingto lighting.
f Press SEL button. The brightness isswitched.u You can adjust the brightness to one of
five levels.
g Press SET button. The brightness of the REVindicator is set, and then the display movesto the display setting of the tachometer.
Operation Guide
36
Instruments (Continued)
2 Changing of tachometer displaymode:You can change the display mode of thetachometer.a Press SEL button to switch the display
mode of tachometer.b Press SET button. The currently selected
displaying mode is set, and the controlreturns to the ordinary display.
Conventional displayShows the engine RPM on the tachometerbar segment.
Peak hold displayShows the engine RPM on the tachometerbar segment and peak hold segment.The peak hold segment keeps to show themaximum engine RPM temporarily.
Ex Engine revolutions per minutes10,500 r/min (rpm)
Operation Guide
37
Conventionaldisplay
Peak holddisplay
Tachometer barsegment
Peak holdsegment
Tachometer barsegment
Indicators
Operation Guide
38
Comes on when thetransmission is in Neutral.
Comes on briefly when the ignition switch is turned to the ON position with the enginestop switch in the (Run) position.If it comes on while engine is running: (P.97)
Neutral indicator
PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL)
If one of these indicators does not come on when it should, have your dealercheck for problems.
Rear ABS (Anti-lock Brake System) OFF indicator CRF300LAComes on briefly when the ignition switch is turned to the ON position.Comes on when the ABS function on the rear wheel is turned off.
Operation Guide
39Continued
High beam indicator
Left turn signal indicator Right turn signal indicator
High coolant temperature indicatorComes on briefly when the ignition switchis turned to the ON position.If it comes on while running: (P.96)
Comes on when the ignition switch is turned to the ON position.Goes off when your speed reaches approximately 6 mph (10 km/h).If it comes on while riding: (P.97)
ABS (Anti-lock Brake System) indicator CRF300LA
REV indicator (P.40)
REV Indicator• Comes on briefly when the ignition switch
is turned to the ON position.Initial settingblinking RPM: 8,000 r/min (rpm)interval RPM: 250 r/min (rpm)
REV indicator r/min (rpm)Blinking(2 times/second) 7,250 r/min (rpm)
Blinking(5 times/second) 7,500 r/min (rpm)
Blinking(10 times/second) 7,750 r/min (rpm)
Lighting 8,000 r/min (rpm)
u Setting of REV indicator: (P.33)
Operation Guide
40
Indicators (Continued)
Operation Guide
41
Switches
Operation Guide
42
Horn button
u Pressing the switch turns the turnsignal off.
Headlight dimmer switch
• : Low beam
Turn signal switch
• : High beam
Switches the ABS function on the rear wheel on/off. (P.45) Rear ABS switch CRF300LA
Operation Guide
43Continued
Ignition switchSwitches the electrical system on/off, locksthe steering.u Key can be removed when in the OFF or
LOCK position.Steering Lock: (P.44)
Engine stop switchShould normally remain in the (Run) position.u In an emergency, switch to the (Stop) position (the starter motor will not operate) to stop
the engine.
Start buttonHeadlight turns off when operating the starter motor.
ONTurns electrical systemon for starting/riding.
LOCK
Turns engine off.OFF
Locks steering.
Switchable when the ignition switch is turned to the ON position. Hazard switch
Steering LockLock the steering when parking to helpprevent theft.A U-shaped wheel lock or similar device isalso recommended.
# Lockinga Turn the handlebar all the way to the left.b Push the key down, and turn the ignition
switch to the LOCK position.u Jiggle the handlebar if the lock is difficult
to engage.c Remove the key.
# UnlockingInsert the key, push it in, and turn the ignitionswitch to the OFF position.
Operation Guide
44
Switches (Continued)
Push
Ignition key
Turn
ABS function on the rear wheelCRF300LAThe ABS function on the rear wheel can beoptionally turned off for off-road riding.u Each time the ignition switch is turned to the
ON position, the ABS function on bothwheels will automatically be turned on.
To turn off the ABS function on the rearwheela Stop the vehicle.b Press and hold the rear ABS switch until the
rear ABS OFF indicator starts flashing, thenrelease the switch while the indicator isflashing.u The rear ABS OFF indicator is on, when
the ABS function on the rear wheel isturned off.
u The ABS function on the rear wheelremains on, if the switch is released afterindicator stops flashing.
To turn on the ABS function on bothwheelsa Stop the vehicle.b Press and hold the rear ABS switch until the
rear ABS OFF indicator is turned off, or turnthe ignition switch to the OFF position andthe ON position.
Operation Guide
45
ABS function onboth wheels is on.
ABS function onrear wheel is off.
Rear ABSswitch
Starting the EngineStart your engine using the following procedure,regardless of whether the engine is cold or warm.
NOTICE• If the engine does not start within 5 seconds, turn
the ignition switch to the OFF position and wait 10seconds before trying to start the engine again torecover battery voltage.
• Extended fast idling and revving the engine candamage the engine, and the exhaust system.
• The engine will not start if the throttle is fully open.
a Make sure the engine stop switch is in the (Run) position.
b Turn the ignition switch to the ON position.c Shift the transmission to Neutral ( N indicator
to come on). Alternatively, pull in the clutchlever to start your vehicle with the transmissionin gear so long as the side stand is raised.
d Press the start button with the throttlecompletely closed.u If you cannot start the engine, open the
throttle slightly (about 1/8 in (3 mm), withoutfreeplay) and press the start button.
Operation Guide
46
About 1/8 in (3 mm), without freeplay
If the engine does not start:aOpen the throttle fully and press the start
button for 5 seconds.bRepeat the normal starting procedure.c If the engine starts, open the throttle slightly
if idling is unstable.d If the engine does not start, wait 10 seconds
before trying steps a & b again.
# If Engine Will Not Start (P.95)
Operation Guide
47
Shifting GearsYour vehicle transmission has 6 forwardgears in a one-down, five-up shift pattern.
If you put the vehicle in gear with the sidestand down, the engine will shut off.
# Recommended Shift PointsShifting UpFrom 1st to 2nd 12 mph (20 km/h)From 2nd to 3rd 19 mph (30 km/h)From 3rd to 4th 25 mph (40 km/h)From 4th to 5th 31 mph (50 km/h)From 5th to 6th 37 mph (60 km/h)
Shifting DownFrom 6th to 5th 28 mph (45 km/h)From 5th to 4th 22 mph (35 km/h)From 4th to 3rd 16 mph (25 km/h)
NOTICEImproper shifting can damage the engine,transmission, and drive train. Also, coasting ortowing the vehicle for long distances with theengine off can damage the transmission.
Operation Guide
48
23
45
6
1
N
Refueling
Do not fill with fuel above the lower edge ofthe filler neck.Fuel type: Unleaded gasoline onlyRecommended fuel octane number:Pump Octane Number (PON) 86 or higher.Tank capacity: 2.06 US gal (7.8 L)
# Refueling and Fuel Guidelines (P.14)
Opening the Fuel Fill CapOpen the lock cover, insert the ignition key,and turn it clockwise to open the fuel fill cap.Closing the Fuel Fill Capa After refueling, align the fuel fill cap latch
with the slot in the filler neck.b Push the fuel fill cap into the filler neck until
it snaps closed and locks.c Remove the key and close the lock cover.
u The key cannot be removed if the fuel fillcap is not locked.
3WARNINGGasoline is highly flammable andexplosive. You can be burned orseriously injured when handling fuel.
• Stop the engine, and keep heat,sparks, and flame away.
• Handle fuel only outdoors.• Wipe up spills immediately.
Operation Guide
49
Ignition keyLower edgeof filler neck
Fuel fill cap Lock cover
Storage EquipmentHelmet HolderThe helmet holder is located on the left sideof the vehicle.
# UnlockingOpen the lock cover, insert the ignition keyand turn it counterclockwise.
# Lockinga Hang your helmet on the holder pin and
push it in to lock.b Remove the key and close the lock cover.
u Use the helmet holder only when parked.
3WARNINGRiding with a helmet attached to theholder can interfere with the rear wheelor suspension and could cause a crashin which you can be seriously hurt orkilled.
Use the helmet holder only whileparked. Do not ride with a helmetsecured by the holder.
Operation Guide
50
Pin
Ignitionkey
Helmetholder
Lock cover
Document Bag and Tool KitThe document bag and tool kit are stored inthe tool box located on the left side of thevehicle.
# OpenInsert the ignition key and turn it clockwise toopen the tool box.
# CloseClose the tool box and push the lockpositions until it is firmly closed. Remove theignition key.u Make sure the tool box is closed before
riding.u As shown in the illustration, wrap the tool kit
with a sponge and store it in the tool box.
Operation Guide
51
Document bag
Ignitionkey
Tool box
Lockposition
Lock position
Tool box
Tool kit
Ignitionkey
Sponge
Lock positionLockposition
Importance of Maintenance ...........................P. 53Maintenance Schedule.....................................P. 55Maintenance Record.........................................P. 58Maintenance Fundamentals ...........................P. 59Removing & Installing Body Components..P. 72
Battery .................................................................... P. 72Clip .......................................................................... P. 73Seat ......................................................................... P. 74Left Shroud ........................................................... P. 75Side Cover............................................................. P. 76
Spark Arrester ....................................................P. 77Engine Oil ............................................................P. 79Coolant.................................................................P. 81Brakes...................................................................P. 83
Side Stand ...........................................................P. 86Drive Chain..........................................................P. 87Wheels..................................................................P. 89Clutch ...................................................................P. 90Throttle ................................................................P. 93
Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefullybefore attempting any maintenance. Refer to “Specifications” for service data.An optional larger tool kit may be available. Check with your Honda dealer's parts department.
Maintenance
Importance of Maintenance
Importance of MaintenanceKeeping your vehicle well-maintained isabsolutely essential to your safety and toprotect your investment, obtain maximumperformance, avoid breakdowns, and reduce airpollution. Maintenance is the owner'sresponsibility. Be sure to inspect your vehiclebefore each ride, and perform the periodicchecks specified in the Maintenance Schedule.2 P. 55
3WARNINGImproperly maintaining your vehicle orfailing to correct a problem before youride can cause a crash in which you canbe seriously hurt or killed.
Always follow the inspection andmaintenance recommendations andschedules in this owner's manual.
For information about the exhaust emission andnoise emission requirements of the U.S.Environmental Protection Agency (EPA), theCalifornia Air Resources Board (CARB), and theEnvironment and Climate Change Canada(ECCC). 2 P. 118
USAMaintenance, replacement or repair of theemission control devices and systems maybe performed by any vehicle repairestablishment or individual using partsthat are “certified” to EPA standards.
Maintenance
53
Maintenance SafetyAlways read the maintenance instructionsbefore you begin each task, and make sure thatyou have the tools, parts, and skills required.We cannot warn you of every conceivablehazard that can arise in performingmaintenance. Only you can decide whether ornot you should perform a given task.
Follow these guidelines when performingmaintenance.● Stop the engine and remove the key.● Place your vehicle on a firm, level surface
using the side stand or a maintenance standto provide support.
● Allow the engine, muffler, brakes, and otherhigh-temperature parts to cool beforeservicing as you can get burned.
● Run the engine only when instructed, anddo so in a well-ventilated area.
Importance of Maintenance
Maintenance
54
Maintenance ScheduleThe maintenance schedule specifies themaintenance requirements necessary to ensuresafe, dependable performance, and properemission control.
Maintenance work should be performed inaccordance with Honda's standards andspecifications by properly trained and equippedtechnicians. Your dealer meets all of theserequirements. All scheduled maintenance isconsidered a normal owner operating cost andwill be charged to you by your dealer. Keepingan accurate maintenance record will helpensure your vehicle is properly maintained.2 P. 58
Make sure whoever performs the scheduledmaintenance completes the maintenancerecord. Retain all service documents. If you sellyour vehicle, these service documents shouldbe transferred with the vehicle to the newowner.
Maintenance
55Continued
ItemsFrequency*1
RegularReplace
Refer topage× 1,000 mi 0.6 4 8 12 16 20 24
× 1,000 km 1.0 6.4 12.8 19.2 25.6 32.0 38.4
Emiss
ion-
relat
ed It
ems
Fuel Line –Throttle Operation 93Air Cleaner*2 –Crankcase Breather*3 –Spark Plug Every 16,000 mi (25,600 km): Every 32,000 mi (51,200 km): –Valve Clearance –Engine Oil 1 Year –Engine Oil Filter –Engine Idle Speed –Radiator Coolant*7 3 Years 81Cooling System –Secondary Air Supply System –Evaporative Emission Control System*4 –
Maintenance Level Maintenance Legend: Intermediate. We recommend service by yourdealer, unless you have the necessary tools and aremechanically skilled.Procedures are provided in an official Honda ServiceManual (2 P. 124).
::::
Inspect (clean, adjust, lubricate, or replace, if necessary)LubricateReplaceClean
: Technical. In the interest of safety, have your vehicleserviced by your dealer.
Maintenance Schedule
Maintenance
56
ItemsFrequency*1
RegularReplace
Refer topage× 1,000 mi 0.6 4 8 12 16 20 24
× 1,000 km 1.0 6.4 12.8 19.2 25.6 32.0 38.4
Non-
Emiss
ion-
Relat
ed It
ems
Drive Chain*5 Every 600 mi (1,000 km): 87Drive Chain Slider –Brake Fluid*7 2 Years 83Brake Pads Wear 84Brake System 59Brake light Switch 85Headlight Aim –Clutch System 90Side Stand 86Suspension –Spark Arrester*6 77Nuts, Bolts, Fasteners*5 –Wheels/Tires*5 69, 89Steering Head Bearings –
Notes:*1 : At higher odometer reading, repeat at the
frequency interval established here.*4*5
::50 STATE (meets California)Service more frequently when riding OFF-ROAD.
*2 : Service more frequently when riding in unusuallywet or dusty areas.
*6*7
::USA only.Replacement requires mechanical skill.
*3 : Service more frequently when riding in rain or at fullthrottle.
Maintenance ScheduleM
aintenance
57
Maintenance Record
Distance Odometer Date Performed By: Notes600 miles (1,000 km)
4,000 miles (6,400 km)8,000 miles (12,800 km)12,000 miles (19,200 km)16,000 miles (25,600 km)20,000 miles (32,000 km)24,000 miles (38,400 km)28,000 miles (44,800 km)32,000 miles (51,200 km)36,000 miles (57,600 km)40,000 miles (64,000 km)44,000 miles (70,400 km)48,000 miles (76,800 km)52,000 miles (83,200 km)56,000 miles (89,600 km)60,000 miles (96,000 km)64,000 miles (102,400 km)68,000 miles (108,800 km)
Maintenance
58
Maintenance Fundamentals
Pre-ride InspectionTo ensure safety, it is your responsibility toperform a pre-ride inspection and make surethat any problem you find is corrected. A pre-ride inspection is a must, not only for safety, butbecause having a breakdown, or even a flat tire,can be a major inconvenience.
Before riding on-road, or returning topavement after riding off-road, take a fewmoments to walk around your vehicle and lookfor any loose parts or anything that appearsunusual.Also check the following.● Tire tread wear and air pressures are within
limits. 2 P. 69● Lights, horn, and turn signals operate
normally.● Check the condition of the drive chain.
Adjust slack and lubricate as needed. 2 P. 67
Check the following items if you are carrying apassenger or cargo:● Combined weight is within load limits.
2 P. 132● Cargo is secured properly.
Check the following items after you get on yourvehicle:● Throttle action moves smoothly without
binding. 2 P. 93● Brake lever and pedal operate normally.● Check the fuel level and refuel when
needed. 2 P. 14, 2 P. 49● Engine stop switch functions properly.
2 P. 43
Maintenance
59Continued
Check the following items at regular intervals:● Oil level is between the upper and lower
level marks. 2 P. 79● Brake fluid level is
Front: above the LOWER level mark. 2 P. 83Rear: above the LWR level mark. 2 P. 83
● Engine coolant level is between the UPPERand LOWER level marks. 2 P. 81
● Side stand functions properly. 2 P. 86
Before riding off-road check all of the precedingplus the following:● Make sure spokes are tight. Check the rims
for any damage. 2 P. 89● Oil level is between the upper and lower
marks. 2 P. 79● Check the fuel level and refuel when
needed. 2 P. 14, 2 P. 49● Be sure the fuel fill cap is securely fastened.
2 P. 49● Clutch lever operates smoothly. Adjust
freeplay if necessary. 2 P. 90● Check for loose cables and other parts, and
anything that appears abnormal.● Use a wrench to check the tightness of all
accessible nuts, bolts and fasteners.
Maintenance Fundamentals
Maintenance
60
Tires and wheels Check the air pressure (2 P. 69), examine tread for wear and damage(2 P. 69), and check the wheels for damage.
Fluid levels Check the engine oil level (2 P. 79), engine coolant level (2 P. 81),and brake fluid level (2 P. 83).
Lights Check that the headlight, brake light, taillight, turn signals and licenseplate light are working properly.
Controls Check the freeplay of the clutch lever (2 P. 90) and throttle grip(2 P. 93).
Drive chain Check the slack (2 P. 87), adjust the slack, and lubricate (2 P. 68) asneeded.
Fuses Check that you have a full supply of spare fuses.Nuts & bolts Check the major nuts and bolts, and tighten as needed.
CrankcaseBreather
Service the crankcase breather more frequently if your vehicle is ridden inthe rain or often at full throttle. Service the breather if you can seedeposits in the transparent section of the drain tube.
Periodic ChecksYou should also perform other periodicmaintenance checks at least once a monthregardless of how often you ride, or more oftenif you ride frequently.
Also, check the odometer reading against theMaintenance Schedule and perform allmaintenance that is due. 2 P. 55
Maintenance FundamentalsM
aintenance
61
Replacing PartsAlways use Honda Genuine Parts or theirequivalents to ensure reliability and safety.When ordering colored components, specifythe model name, color, and code mentioned onthe color label.The color label is attached to the right side ofthe frame.
3WARNINGInstalling non-Honda parts may makeyour vehicle unsafe and cause a crash inwhich you can be seriously hurt orkilled.
Always use Honda Genuine Parts orequivalents that have been designedand approved for your vehicle.
Maintenance Fundamentals
Maintenance
62
Color label
BatteryYour vehicle has a maintenance-free typebattery. You do not have to check the batteryelectrolyte level or add distilled water. Clean thebattery terminals if they become dirty orcorroded.Do not remove the battery cap seals. There isno need to remove the cap when charging.
NOTICEAn improperly disposed of battery can beharmful to the environment and human health.Always confirm local regulations for properbattery disposal instruction.
# What to do in an emergencyIf any of the following occur, immediately seeyour doctor.● Electrolyte splashes into your eyes:
u Wash your eyes repeatedly with coolwater for at least 15 minutes. Using waterunder pressure can damage your eyes.
● Electrolyte splashes onto your skin:u Remove affected clothing and wash your
skin thoroughly using water.● Electrolyte splashes into your mouth:
u Rinse mouth thoroughly with water, anddo not swallow.
3WARNINGThe battery gives off explosivehydrogen gas during normal operation.
A spark or flame can cause the batteryto explode with enough force to kill orseriously hurt you.
Wear protective clothing and a faceshield, or have a skilled mechanic dothe battery servicing.
WARNING: Battery posts, terminals, and relatedaccessories contain lead and lead compounds.Wash your hands after handling.
Maintenance FundamentalsM
aintenance
63Continued
# Cleaning the Battery Terminals1. Remove the battery. 2 P. 722. If the terminals are starting to corrode and
are coated with a white substance, washwith warm water and wipe clean.
3. If the terminals are heavily corroded, cleanand polish the terminals with a wire brush orsandpaper. Wear safety glasses.
4. After cleaning, reinstall the battery.
The battery has a limited life span. Consult yourdealer about when you should replace thebattery. Always replace the battery with anothermaintenance-free battery of the same type.
# ChargingIf you use electrical accessories that drain thebattery or you do not ride frequently, werecommend that you charge the battery every30 days using a charger designed specifically foryour Honda, which can be purchased from yourdealer. Read the information that came withyour battery charger and follow the instructionson the battery. Avoid using an automobile-typebattery charger, as these can overheat amotorcycle battery and cause permanentdamage.Make sure the ignition switch is in the OFFposition before charging the battery.
NOTICEImproper charging can damage the battery. Ifyou can’t charge the battery or it appears unableto hold a charge, contact your dealer.
Maintenance Fundamentals
Maintenance
64
NOTICEJump starting using an automobile battery candamage your vehicle's electrical system and isnot recommended. Bump starting is also notrecommended.
NOTICEInstalling non-Honda electrical accessories canoverload the electrical system, discharging thebattery and possibly damaging the system.
FusesFuses protect the electrical circuits on yourvehicle. If something electrical on your vehiclestops working, check for and replace any blownfuses. 2 P. 104
# Inspecting and Replacing FusesTurn the ignition switch to the OFF position toremove and inspect fuses. If a fuse is blown,replace with a fuse of the same rating. For fuseratings, see “Specifications.” 2 P. 134
NOTICEReplacing a fuse with one that has a higher rating greatlyincreases the chance of damage to the electrical system.
If a fuse fails repeatedly, you likely have anelectrical fault. Have your vehicle inspected byyour dealer.
Maintenance FundamentalsM
aintenance
65
Blown fuse
Engine OilEngine oil consumption varies and oil qualitydeteriorates according to riding conditions andtime elapsed.Check the engine oil level regularly, and add therecommended engine oil if necessary. Dirty oil orold oil should be changed as soon as possible.
# Selecting the Engine OilFor recommended engine oil, see“Specifications.” 2 P. 133
If you use non-Honda engine oil, check thelabel to make sure that the oil satisfies all of thefollowing standards:● JASO T 903 standard*1: MA● SAE standard*2: 10W-30● API classification*3: SG or higher
*1. The JASO T 903 standard is an index for engineoils for 4-stroke motorcycle engines. There aretwo classes: MA and MB. For example, thefollowing label shows the MA classification.
*2. The SAE standard grades oils by their viscosity.*3. The API classification specifies the quality and
performance rating of engine oils. Use SG orhigher oils, excluding oils marked as “EnergyConserving” or “Resource Conserving” on thecircular API service symbol.
Maintenance Fundamentals
Maintenance
66
Oil codeOil classification
Not recommended Recommended
Brake FluidDo not add or replace brake fluid, except in anemergency. Use only fresh brake fluid from asealed container. If you do add fluid, have thebrake system serviced by your dealer as soon aspossible.
NOTICEBrake fluid can damage plastic and painted surfaces.Wipe up spills immediately and wash thoroughly.
Recommended brake fluid:Honda DOT 3 or DOT 4 Brake Fluid orequivalent
3WARNINGClean filler cap before removing. Useonly DOT 3 or DOT 4 fluid from asealed container.
Drive ChainThe drive chain must be inspected andlubricated regularly. Inspect the chain morefrequently if you often ride on bad roads, ride athigh speed, or ride with repeated fastacceleration. 2 P. 87If the chain does not move smoothly, makesstrange noises, has damaged rollers, has loosepins, has missing O-rings, or kinks, have thechain inspected by your dealer.
Also inspect the drive sprocket and drivensprocket. If either has worn or damaged teeth,have the sprocket replaced by your dealer.
Maintenance FundamentalsM
aintenance
67Continued
Normal(GOOD)
Worn(REPLACE)
Damaged(REPLACE)
NOTICEUse of a new chain with worn sprockets will causerapid chain wear.
# Cleaning and LubricatingAfter inspecting the slack, clean the chain andsprockets while rotating the rear wheel. Use adry cloth with chain cleaner designedspecifically for O-ring chains, or neutraldetergent. Use a soft brush if the chain is dirty.After cleaning, wipe dry and lubricate with therecommended lubricant.
Recommended lubricant:Pro Honda HP Chain Lube or equivalent
Do not use a steam cleaner, a high pressurecleaner, a wire brush, volatile solvent such asgasoline and benzene, abrasive cleaner, chaincleaner or lubricant NOT designed specificallyfor O-ring chains as these can damage therubber O-ring seals.Avoid getting lubricant on the brakes or tires.Avoid applying excess chain lubricant to preventspray onto your clothes and the vehicle.
Recommended CoolantPro Honda HP Coolant is a pre-mixed solutionof antifreeze and distilled water.
Concentration:50% antifreeze and 50% distilled water
A concentration of antifreeze below 40% willnot provide proper corrosion and coldtemperature protection.A concentration of up to 60% will provide betterprotection in colder climates.
Maintenance Fundamentals
Maintenance
68
NOTICEUsing coolant not specified for aluminum enginesor tap/mineral water can cause corrosion.
Crankcase BreatherService more frequently when riding in rain, atfull throttle, or after the vehicle is washed oroverturned. Service if the deposit level can beseen in the transparent section of the draintube.If the drain tube overflows, the air filter maybecome contaminated with engine oil causingpoor engine performance.
Tires (Inspecting/Replacing)# Checking the Air PressureVisually inspect your tires and use an airpressure gauge to measure the air pressurebefore each off-road ride and whenever youreturn to pavement after riding off-road. If you
only ride on pavement, check the pressure atleast once a month or any time you think thetires look low. Always check air pressure whenyour tires are cold.If you decide to adjust the tire pressure for aparticular off-road riding condition, makechanges a little at a time.
# Inspecting for DamageInspect the tires forcuts, slits, or cracks thatexposes fabric orcords, or nails or otherforeign objectsembedded in the sideof the tire or the tread.
Also inspect for any unusual bumps or bulges inthe side walls of the tires.
Maintenance FundamentalsM
aintenance
69Continued
# Inspecting for Abnormal WearInspect the tires forsigns of abnormal wearon the contact surface.
# Inspecting Tread DepthInspect the tread wear indicators. If theybecome visible, replace the tires immediately.For safe riding, you should replace the tireswhen the minimum tread depth is reached.
# Inspecting Rims and Valve StemsInspect the rims for damage and loose spokes.Also inspect the valve stems for their positions.A tilted valve stem indicates the tube is slippinginside the tire or the tire is slipping on the rim.See your dealer.
3WARNINGRiding on tires that are excessively wornor improperly inflated can cause a crashin which you can be seriously hurt orkilled.
Follow all instructions in this owner'smanual regarding tire inflation andmaintenance.
Maintenance Fundamentals
Maintenance
70
Wear indicatorlocation mark
or TWI
Have your tires replaced by your dealer.For recommended tires, air pressure andminimum tread depth, see “Specifications.”2 P. 133Follow these guidelines whenever you replacetires.● Use the recommended tires or equivalents
of the same size, construction, speed rating,and load range.
● Remember to replace the inner tubewhenever you replace a tire. The old tubewill probably be stretched, and it could fail ifinstalled in a new tire.
3WARNINGInstalling improper tires on your vehiclecan adversely affect handling andstability, and can cause a crash in whichyou can be seriously hurt or killed.
Always use the size and type of tiresrecommended in this owner's manual.
Maintenance FundamentalsM
aintenance
71
Removing & Installing Body Components
Battery
# RemovalMake sure the ignition switch is in the OFFposition.1. Remove the left shroud. 2 P. 75
2. Remove the bolt and the battery holder.3. Disconnect the negative - terminal from
the battery.4. Disconnect the positive + terminal from
the battery.5. Remove the battery taking care not to
drop the terminal nuts.
# InstallationInstall the parts in the reverse order ofremoval. Always connect the positive +terminal first. Make sure that bolts and nutsare tight.Make sure the clock information is correctafter the battery is reconnected. 2 P. 30For proper handling of the battery, see“Maintenance Fundamentals.” 2 P. 63“Battery Goes Dead.” 2 P. 100
Maintenance
72
Negativeterminal
Positive terminal
Battery
Batteryholder
Bolt
Clip# Removal1. Press down on the center pin to release
the lock.2. Pull the clip out of the hole.
# Installation1. Push the bottom of the center pin.
2. Insert the clip into the hole.3. Press down on the center pin to lock the
clip.
Removing & Installing Body Components u ClipM
aintenance
73
Center pin
Seat # Removal1. Remove the hook bolts and collars.2. Pull the seat back and up.
# Installation1. Align the recess with the tab and insert
the prongs into the stays and attach theseat as shown.
2. Install the collars onto the hook bolts.Tighten the hook bolts.
Torque: 15 lbf·ft (21 N·m, 2.1 kgf·m)
Removing & Installing Body Components u Seat
Maintenance
74
Hook bolt
Rear prongs
Hook bolt
Collar
Tab
Front stays
Front prongs
Seat
Rear stays
Collar
Recess
Left Shroud # Removal1. Remove the left side cover. 2 P. 762. Remove the clips. 2 P. 733. Remove the bolts.4. Remove the left shroud.
# Installation1. Install the left shroud.2. Install and tighten the bolts.3. Install the clips.4. Install the left side cover.
Removing & Installing Body Components u Left ShroudM
aintenance
75
Bolts
BoltClips
Left shroud
Side CoverThe right and left side covers can beremoved in the same manner.
# Removal1. Remove the seat. 2 P. 742. Remove the clip. 2 P. 733. Remove the bolt.4. Remove the prongs from the grommets.5. Remove the side cover.
# InstallationInstall the parts in the reverse order ofremoval.
Removing & Installing Body Components u Side Cover
Maintenance
76
Bolt
Side cover
Grommets Prongs
Clip
Spark Arrester
Cleaning the Spark ArresterRegular servicing prevents carbon buildup(which can diminish engine performance)and also complies with USDA regulations forregular maintenance to assure properfunction. The spark arrester prevents randomsparks from the combustion process in yourengine from reaching the environment.
1. Allow the engine and muffler to cool.2. Remove the right side cover. 2 P. 763. Remove the muffler cover bolts and
muffler cover from the muffler.4. Remove the tail cap cover screws and tail
cap cover from the muffler.
Maintenance
77Continued
Spark arresterGasket
Spark arrestermounting bolts
Tail cap coverscrews
Tail cap cover
Muffler coverbolts
Muffler cover
5. Remove the spark arrester mountingbolts, spark arrester and gasket from themuffler.
6. Use a brush to remove carbon depositsfrom the spark arrester screen. Be carefulto avoid damaging the spark arresterscreen. The spark arrester must be free ofbreaks and holes. Replace, if necessary.Check the gasket. Replace, if necessary.
7. Install the gasket and the spark arrester,and tighten the spark arrester mountingbolts.
Torque: 6.6 lbf·ft (9.0 N·m, 0.9 kgf·m)
8. Install the tail cap cover and tighten thetail cap cover screws.
Torque: 3.9 lbf·ft (5.25 N·m, 0.5 kgf·m)
9. Install the muffler cover and tighten themuffler cover bolts.
10. Install the right side cover.
Spark Arrester u Cleaning the Spark Arrester
Maintenance
78
Spark arrester screen
Engine Oil
Checking the Engine Oil1. If the engine is cold, idle the engine for 3
to 5 minutes.2. Turn the ignition switch to the OFF
position and wait for 2 to 3 minutes.3. Place your vehicle in an upright position
on a firm, level surface.4. Check that the oil level is between the
upper level and lower level marks on theoil level inspection window.
Maintenance
79
Oil fill cap
Oil levelinspectionwindowUpper levelmark
Lower levelmark
Adding Engine OilIf the engine oil is below or near the lowerlevel mark, add the recommended engine oil.2 P. 66, 2 P. 1331. Remove the oil fill cap. Add the
recommended oil until it reaches theupper level mark.u Place your vehicle in an upright
position on a firm, level surface whenchecking the oil level.
u Do not overfill above the upper levelmark.
u Make sure no foreign objects enter theoil filler opening.
u Wipe up any spills immediately.2. Securely reinstall the oil fill cap.
NOTICEOverfilling with oil or operating with insufficientoil can cause damage to your engine. Do not mixdifferent brands and grades of oil. They mayaffect lubrication and clutch operation.
For the recommended oil and oil selectionguidelines, see “Maintenance Fundamentals.”2 P. 66
Engine Oil u Adding Engine Oil
Maintenance
80
Coolant
Checking the CoolantCheck the coolant level in the reserve tankwhile the engine is cold.
1. Place your vehicle on a firm, level surface.2. Hold your vehicle in an upright position.3. Check that the coolant level is between
the UPPER level and LOWER level markson the reserve tank.
If the coolant level is dropping noticeably orthe reserve tank is empty, you likely have aserious leak. Have your vehicle inspected byyour dealer.
Maintenance
81
UPPER levelmark
LOWER levelmark
Reserve tank
Reserve tank cap
Adding CoolantIf the coolant level is below the LOWER levelmark, add the recommended coolant(2 P. 68) until the level reaches the UPPERlevel mark.Add fluid only from the reserve tank cap anddo not remove the radiator cap.1. Remove the reserve tank cap and add
fluid while monitoring the coolant level.u Do not overfill above the UPPER level
mark.u Make sure no foreign objects enter the
reserve tank opening.2. Securely reinstall the reserve tank cap.
3WARNINGRemoving the radiator cap while theengine is hot can cause the coolant tospray out, potentially scalding you.
Always let the engine and radiator cooldown before removing the radiator cap.
Coolant u Adding Coolant
Maintenance
82
Brakes
Checking Brake Fluid1. Place your vehicle in an upright position
on a firm, level surface.2. Front Check that the brake fluid reservoir
is horizontal and that the fluid level isabove the LOWER level mark.Rear Check that the brake fluid reservoiris horizontal and that the fluid level isabove the LWR mark.
If the brake fluid level in either reservoir isbelow the LOWER level mark/LWR mark orthe brake lever and pedal freeplay becomesexcessive, inspect the brake pads for wear.If the brake pads are not worn, you mostlikely have a leak. Have your vehicleinspected by your dealer.
Maintenance
83
Front brake fluid reservoir
LOWER level mark
LWR mark
Rear brake fluid reservoirFront Rear
Inspecting the Brake PadsCheck the condition of the brake pad wearindicators.The pads need to be replaced if a brake padis worn to the indicator.
1. Front Inspect the brake pads from belowthe brake caliper.
2. Rear Inspect the brake pads from the rearright of the vehicle.
If necessary have the pads replaced by yourdealer.Always replace both left and right brake padsat the same time.
Brakes u Inspecting the Brake Pads
Maintenance
84
Front Rear Pads
Wearindicator
Disc
Pads
Wearindicator
Disc
Wearindicator
Wearindicator
Adjusting the Brake LightSwitchCheck the operation of the brake light switch.Hold the brake light switch and turn theadjusting nut in the direction A if the switchoperates too late, or turn the nut in thedirection B if the switch operates too soon.
Brakes u Adjusting the Brake Light SwitchM
aintenance
85
Brake light switch
Adjusting nut
BA
Side Stand
Checking the Side Stand
1. Check that the side stand operatessmoothly. If the side stand is stiff orsqueaky, clean the pivot area andlubricate the pivot bolt with clean grease.
2. Check the spring for damage or loss oftension.
3. Sit on the vehicle, shift the transmission toNeutral, and raise the side stand.
4. Start the engine, pull the clutch lever in,and shift the transmission into gear.
5. Lower the side stand all the way. Theengine should stop as you lower the sidestand. If the engine doesn't stop, haveyour vehicle inspected by your dealer.
Maintenance
86
Side standspring
Drive Chain
Inspecting the Drive ChainSlackCheck the drive chain slack at several pointsalong the chain. If the slack is not constant atall points, some links may be kinked andbinding.Have the chain inspected by your dealer.
1. Shift the transmission to Neutral. Stop theengine.
2. Place your vehicle on its side stand on afirm, level surface.
3. Insert a scale through the slit on the chaincase.
Maintenance
87Continued
Chain case
Slit
Scale
4. Pull up the drive chain and check theslack between the top of the swingarmand the drive chain by the scale.
Drive chain slack:2 - 2 1/4 in (50 - 55 mm)
u Do not ride your vehicle if the slackexceeds 2 1/4 in (57 mm).
5. Roll the vehicle forward and check thatthe chain moves smoothly.
6. Inspect the sprockets. 2 P. 677. Clean and lubricate the drive chain.
2 P. 68
Drive Chain u Inspecting the Drive Chain Slack
Maintenance
88
Top ofswingarm
Drive chain
Wheels
Wheels Rims & SpokesKeeping the wheels true (round) andmaintaining correct spoke tension is critical tosafe vehicle operation.Excessively loose spokes may result ininstability at high speeds and possible loss ofcontrol.It is not necessary to remove the wheels toperform the recommended service in theMaintenance Schedule. 2 P. 99
1. Inspect the wheel rims and spokes fordamage.
2. Tighten any loose spokes.
3. Rotate the wheel slowly to see if itappears to “wobble.” If it does, the rim isout of round or not “true.” If the wobble isnoticeable, see your dealer for inspection.
Maintenance
89
Wheelrim
Spoke
Clutch
Checking the Clutch# Checking the Clutch Lever FreeplayCheck the clutch lever freeplay.
Freeplay at the clutch lever:3/8 - 13/16 in (10 - 20 mm)
Check the clutch cable for kinks or signs ofwear. If necessary have it replaced by yourdealer.Lubricate the clutch cable with acommercially available cable lubricant toprevent premature wear and corrosion.
NOTICEImproper freeplay adjustment can causepremature clutch wear.
Maintenance
90
Clutch lever
Freeplay
Adjusting the Clutch LeverFreeplay# Minor AdjustmentAttempt adjustment with the minor clutchcable adjuster first.
1. Pull back the rubber dust cover.2. Loosen the minor lock nut.3. Turn the minor clutch cable adjuster until
the freeplay is 3/8 - 13/16 in (10 - 20 mm).4. Tighten the minor lock nut and check the
freeplay again.5. Install the rubber dust cover.
Clutch u Adjusting the Clutch Lever FreeplayM
aintenance
91Continued
Rubber dustcover
Minorlock nut
Minor clutchcableadjuster
–
+
# Major AdjustmentIf the minor clutch cable adjuster is threadedout near its limit, or the correct freeplaycannot be obtained, attempt adjustment withthe major clutch cable adjuster.1. Pull back the rubber dust cover. Loosen
the minor lock nut and turn the minorclutch cable adjuster all the way in (toprovide maximum freeplay). Tighten theminor lock nut. Install the rubber dustcover.
2. Loosen the major lock nut.3. Turn the major clutch cable adjuster until
the clutch lever freeplay is 3/8 - 13/16 in(10 - 20 mm).
4. Tighten the major lock nut and check theclutch lever freeplay.
5. Start the engine, pull the clutch lever in,and shift into gear. Make sure the enginedoes not stall and the vehicle does not
creep. Gradually release the clutch leverand open the throttle. Your vehicle shouldmove smoothly and accelerate gradually.
If proper adjustment cannot be obtained orthe clutch does not work correctly, see yourdealer.
Clutch u Adjusting the Clutch Lever Freeplay
Maintenance
92
Major clutch cable adjuster
Major lock nut
–
+
Throttle
Checking the ThrottleWith the engine off, check that the throttlerotates smoothly from fully closed to fullyopen in all steering positions and throttlefreeplay is correct. If the throttle does notmove smoothly, close automatically, or if thecable is damaged, have the vehicle inspectedby your dealer.
Freeplay at the throttle grip flange:1/16 - 1/4 in (2 - 6 mm)
Adjusting the Throttle Freeplay1. Loosen the lock nut.2. Turn the adjuster until the freeplay is
1/16 - 1/4 in (2 - 6 mm).3. Tighten the lock nut and inspect the
throttle action again.
Maintenance
93
Freeplay
Flange
Throttle grip Adjuster
Lock nut
+
–
Engine Will Not Start........................................P. 95Overheating (High coolant temperatureindicator is on) .................................................P. 96
Warning Indicators On or Flashing...............P. 97PGM-FI (Programmed Fuel Injection)Malfunction Indicator Lamp (MIL) ................. P. 97
ABS (Anti-lock Brake System) Indicator ......... P. 97Other Warning Indications..............................P. 98
Fuel Gauge Failure Indication........................... P. 98Tire Puncture ......................................................P. 99Electrical Trouble.............................................P. 100
Battery Goes Dead............................................ P. 100Burned-out Light Bulb ..................................... P. 100Blown Fuse.......................................................... P. 104
Unstable Engine Operation OccursIntermittently .................................................P. 107
Troubleshooting
Engine Will Not Start
Starter Motor Operates ButEngine Does Not StartCheck the following items:● Check the correct engine starting
sequence. 2 P. 46● Check that there is gasoline in the fuel
tank.● Check if the PGM-FI malfunction indicator
lamp (MIL) is on.u If the indicator lamp is on, contact
your dealer as soon as possible.
Starter Motor Does NotOperateCheck the following items:● Check the correct engine starting
sequence. 2 P. 46● Make sure engine stop switch is in the
(Run) position. 2 P. 43● Check for a blown fuse. 2 P. 104● Check for a loose battery connection
(2 P. 72) or battery terminal corrosion(2 P. 63).
● Check the condition of the battery.2 P. 100
If the problem continues, have your vehicleinspected by your dealer.
Troubleshooting
95
Overheating (High coolant temperature indicator is on)The engine is overheating when the followingoccurs:● High coolant temperature indicator
comes on.● Acceleration becomes sluggish.
If this occurs, pull safely to the side of theroad and perform the followingprocedure.
Extended fast idling may cause the highcoolant temperature indicator to come on.
NOTICEContinuing to ride with an overheated enginecan cause serious damage to the engine.
1. Stop the engine using the ignition switch,and then turn the ignition switch to theON position.
2. Check that the radiator fan is operating,and then turn the ignition switch to theOFF position.
If the fan is not operating:Suspect a fault. Do not start the engine.Transport your vehicle to your dealer.If the fan is operating:Allow the engine to cool with the ignitionswitch in the OFF position.
3. After the engine has cooled, inspect theradiator hose and check if there is a leak.2 P. 81If there is a leak:Do not start the engine. Transport yourvehicle to your dealer.
4. Check the coolant level in the reservetank. 2 P. 81u Add coolant as necessary.
5. If 1-4 check normal, you may continueriding, but closely monitor the highcoolant temperature indicator.
Troubleshooting
96
Warning Indicators On or Flashing
PGM-FI (Programmed FuelInjection) MalfunctionIndicator Lamp (MIL)If the indicator comes on while riding, youmay have a serious problem with the PGM-FIsystem. Reduce speed and have your vehicleinspected by your dealer as soon as possible.
ABS (Anti-lock Brake System)IndicatorCRF300LAIf the indicator operates in one of thefollowing ways, you may have a seriousproblem with the ABS. Reduce your speedand have your vehicle inspected by yourdealer as soon as possible.
● Indicator comes on or starts flashing whileriding.
● Indicator does not come on when theignition switch is in the ON position.
● Indicator does not go off at speeds above6 mph (10 km/h).
If the ABS indicator stays on, your brakes willcontinue to work as a conventional system,but without the anti-locking function.
The ABS indicator may flash if you turn therear wheel while the rear wheel is lifted offthe ground. In this case, turn the ignitionswitch to the OFF position, and then to theON position again. The ABS indicator will gooff after your speed reaches 19 mph (30km/h).
Troubleshooting
97
Other Warning Indications
Fuel Gauge Failure IndicationIf the fuel system has an error, the fuel gaugeindicators will be displayed as shown in theillustration.If this occurs, see your dealer as soon aspossible.
Troubleshooting
98
Tire PunctureRepairing a puncture or removing a wheelrequires special tools and technical expertise.We recommend you have this type of serviceperformed by your dealer.After an emergency repair, always have thetire inspected/replaced by your dealer.
Tube Repair and ReplacementIf a tube is punctured or damaged, youshould replace it as soon as possible. A tubethat is repaired may not have the samereliability as a new one, and it may fail whileyou are riding.If you need to make a temporary repair bypatching a tube or using an aerosol sealant,ride cautiously at reduced speed and havethe tube replaced before you ride again.Anytime a tube is replaced, the tire should becarefully inspected as described.
3WARNINGRiding your vehicle with a temporarytire or tube repair can be risky. If thetemporary repair fails, you can crashand be seriously injured or killed.
If you must ride with a temporary tire ortube repair, ride slowly and carefullyand do not exceed 30 mph (50 km/h)until the tire or tube is replaced.
Troubleshooting
99
Electrical Trouble
Battery Goes DeadCharge the battery using a motorcyclebattery charger.Remove the battery from the vehicle beforecharging.Do not use an automobile-type batterycharger, as these can overheat a motorcyclebattery and cause permanent damage. If thebattery does not recover after recharging,contact your dealer.
NOTICEJump starting using an automobile battery candamage your vehicle's electrical system and isnot recommended.Bump starting is also not recommended.
Burned-out Light BulbFollow the procedure below to replace aburned-out light bulb.Turn the ignition switch to the OFF or LOCKposition.Allow the bulb to cool before replacing it.Do not use bulbs other than those specified.Check the replacement bulb for correctoperation before riding.
For the light bulb wattage, see“Specifications.” 2 P. 134
The license plate light uses several LEDs. Ifthere is an LED which is not turned on, seeyour dealer for servicing.
Troubleshooting
100
# Headlight Bulb1. Remove the bolts.2. Remove the headlight assembly.3. Pull off the socket while pressing the tabs.
4. Remove the dust cover.5. Press the pin down and pull out the bulb
without turning it.6. Install a new bulb and parts in the reverse
order of removal.u Install the dust cover with its tabs
positioned vertically.Do not touch the glass surface with yourfingers. If you touch the bulb with your barehands, clean it with a cloth moistened withisopropyl (rubbing) alcohol.
Electrical Trouble u Burned-out Light BulbTroubleshooting
101Continued
Headlight assembly
Bolts
Bolts
Tabs
Socket
Pin
TabsBulbDust cover
# Brake light/Taillight Bulb1. Remove the seat. 2 P. 742. Remove the hook bolts and collars.3. Remove the prongs from the grommets.4. Remove the rear fender.
5. Turn the socket counterclockwise, andremove it.
6. Slightly press the bulb and turn itcounterclockwise.
7. Install a new bulb and parts in the reverseorder of removal.
8. Tighten the hook bolts.
Torque: 15 lbf·ft (21 N·m, 2.1 kgf·m)
Electrical Trouble u Burned-out Light Bulb
Troubleshooting
102
Hook bolt RearfenderCollar
Collar
Hook bolt
Grommets
Prong
Prong
BulbSocket
# Front/Rear Turn Signal Bulb1. Remove the screw.2. Remove the turn signal lens.3. Slightly press the bulb and turn it
counterclockwise.
4. Install a new bulb and parts in the reverseorder of removal.
Electrical Trouble u Burned-out Light BulbTroubleshooting
103
Turn signal lens
Screw
Bulb
Blown FuseBefore handling fuses, see “Inspecting andReplacing Fuses.” 2 P. 65
# Fuse Box A1. Remove the seat. 2 P. 742. Open the fuse box cover.3. Pull the fuses out with the fuse puller in
the tool kit one by one check for a blownfuse. Always replace a blown fuse with aspare of the same rating.
4. Close the fuse box cover.5. Install the seat.
Electrical Trouble u Blown Fuse
Troubleshooting
104
Fuse box coverSpare fuse
# Main Fuse 1. Remove the left side cover. 2 P. 762. Pull the starter magnetic switch out.3. Disconnect the wire connector of the
starter magnetic switch.4. Pull the main fuse out and check for a
blown fuse.Always replace a blown fuse with a sparefuse of the same rating.u Spare main fuse is provided in the
starter magnetic switch.5. Reinstall parts in the reverse order of
removal.
Electrical Trouble u Blown FuseTroubleshooting
105Continued
Starter magneticswitch
Mainfuse
Sparemain fuse
Wire connector
# Fuse Box BCRF300LA only
1. Remove the left side cover. 2 P. 762. Open the fuse box cover.3. Pull the fuses out with the fuse puller in
the tool kit one by one check for a blownfuse. Always replace a blown fuse with aspare fuse of the same rating.
4. Close the fuse box cover.5. Reinstall parts in the reverse order of
removal.
NOTICEIf a fuse fails repeatedly, you likely have anelectrical problem. Have your vehicle inspectedby your dealer.
Electrical Trouble u Blown Fuse
Troubleshooting
106
Sparefuse
Fuse box cover
Unstable Engine Operation Occurs IntermittentlyIf the fuel pump filter is clogged, unstableengine operation will occur intermittentlywhile riding.Even if this symptom occurs, you cancontinue to ride your vehicle.If unstable engine operation occurs even ifsufficient fuel is available, have your vehicleinspected by your dealer as soon as possible.
Troubleshooting
107
Keys.....................................................................P. 109Instruments, Controls, & Other Features...P. 110Caring for Your Vehicle..................................P. 111Storing Your Vehicle.......................................P. 114Transporting Your Vehicle ............................P. 115You & the Environment .................................P. 116Vehicle Identification Number.....................P. 117Emission Control Systems .............................P. 118Catalytic Converter .........................................P. 122Oxygenated Fuels............................................P. 123Authorized Manuals .......................................P. 124Warranty Coverage and Service ..................P. 125Honda Contacts ...............................................P. 128Reporting Safety Defects ..............................P. 130
Information
KeysIgnition Key
Be sure to record the key number provided withthe key number plate. Store the spare key andkey number in a safe location.To make a duplicate, take the spare key or thekey number to your dealer.If you lose all ignition keys and the key number,the ignition switch assembly will probably haveto be removed by your dealer to determine thekey number.
A metal key holder may cause damage to thearea surrounding the ignition switch.
KeysInform
ation
109
Instruments, Controls, &Other FeaturesIgnition Switch
Leaving the ignition switch in the ON positionwith the engine stopped will drain the battery.
Do not turn the key while riding.
Engine Stop SwitchDo not use the engine stop switch except in anemergency. Doing so when riding will cause theengine to suddenly turn off, making ridingunsafe.If you stop the engine using the engine stopswitch, turn the ignition switch to the OFFposition. Failing to do so will drain the battery.
OdometerThe display locks at 999,999 when the read-outexceeds 999,999.
TripmeterThe tripmeters return to 0.0 when each read-out exceeds 9,999.9.
Document BagThe owner's manual, registration, and insuranceinformation can be stored in the plasticdocument bag located under the seat.
Ignition Cut-off SystemA banking (lean angle) sensor automaticallystops the engine and fuel pump if the vehiclefalls over. To reset the sensor, you must turn theignition switch to the OFF position and back tothe ON position before the engine can berestarted.
Instruments, Controls, & Other Features
Information
110
Assist-slipper Clutch SystemThe assist-slipper clutch system helps to preventthe rear tire from locking up when thedeceleration of your vehicle produces a strongengine braking effect. It also makes the clutchlever operation feel lighter.Use only MA classification engine oil for yourvehicle. Using engine oil other than MAclassification oil could result in damage to theassist-slipper clutch system.
Caring for Your VehicleFrequent cleaning and polishing is important toensure the life of your Honda. A clean vehiclemakes it easier to spot potential problems.In particular, seawater and salts used to preventice on roads promote the formation ofcorrosion. Always wash your vehicle thoroughlyafter riding on coastal or treated roads.
WashingAllow the engine, muffler, brakes, and otherhigh-temperature parts to cool before washing.1. Rinse your vehicle thoroughly using a low
pressure garden hose to remove loose dirt.2. If necessary, use a sponge or a soft towel
with mild cleaner to remove road grime.u Clean the headlight lens, panels, and
other plastic components with extra careto avoid scratching them.Avoid directing water into the air cleaner,muffler, and electrical parts.
Caring for Your VehicleInform
ation
111Continued
3. Thoroughly rinse your vehicle with plenty ofclean water and dry with a soft, clean cloth.
4. After the vehicle dries, lubricate any movingparts.u Make sure that no lubricant spills onto
the brakes or tires. Brake discs, pads,drum or shoes contaminated with oil willsuffer greatly reduced brakingeffectiveness and can lead to a crash.
5. Lubricate the drive chain immediately afterwashing and drying the vehicle.
6. Apply a coat of wax to prevent corrosion.u Avoid products that contain harsh
detergents or chemical solvents. Thesecan damage the metal, paint, and plasticon your vehicle.Keep the wax clear of the tires and brakes.
u If your vehicle has any matte paintedparts, do not apply a coat of wax to thematte painted surface.
# Washing PrecautionsFollow these guidelines when washing:● Do not use high-pressure washers:
u High-pressure water cleaners candamage moving parts and electricalparts, rendering them inoperable.
u Water in the air intake can be drawn intothe throttle body and/or enter the aircleaner.
● Do not direct water at the muffler:u Water in the muffler can prevent starting
and causes rust in the muffler.● Dry the brakes:
u Water adversely affects brakingeffectiveness. After washing, apply thebrakes intermittently at low speed tohelp dry them.
● Do not direct water at the tool box:u Water in the tool box can damage your
documents and other belongings.● Do not direct water at the air cleaner:
u Water in the air cleaner can prevent theengine from starting.
Caring for Your Vehicle
Information
112
● Do not direct water near the headlight:u The headlight's inside lens may fog
temporarily after washing or while ridingin the rain. This does not impact theheadlight function.
u Any condensation inside the headlightshould dissipate after a few minutes ofrunning the engine with the headlight(s)on.However, if you see a large amount ofwater or ice accumulated inside thelens(es), have your vehicle inspected byyour dealer.
● Do not use wax or polishing compounds onmatte painted surface:u Use a soft cloth or sponge, plenty of
water, and a mild detergent to cleanmatte painted surfaces. Dry with a softclean cloth.
Aluminum ComponentsAluminum will corrode from contact with dirt,mud, or road salt. Clean aluminum partsregularly and follow these guidelines to avoidscratches:● Do not use stiff brushes, steel wool, or
cleaners containing abrasives.● Avoid riding over or scraping against curbs.
PanelsFollow these guidelines to prevent scratchesand blemishes:● Wash gently using a soft sponge and plenty
of water.● To remove stubborn stains, use diluted
detergent and rinse thoroughly with plentyof water.
● Avoid getting gasoline, brake fluid, ordetergents on the instruments, panels, orheadlight.
Caring for Your VehicleInform
ation
113Continued
Exhaust Pipe and MufflerWhen the exhaust pipe and muffler are painted,do not use a commercially available abrasivekitchen cleaning compound. Use a neutraldetergent to clean the painted surface on theexhaust pipe and muffler. If you are not sure ifyour exhaust pipe and muffler are painted,contact your dealer.
Storing Your VehicleIf you store your vehicle outdoors, you shouldconsider using a full-body cover.If you won't be riding for an extended period,follow these guidelines:● Wash your vehicle and wax all painted
surfaces (except matte painted surfaces).Coat chrome pieces with rust-inhibiting oil.
● Lubricate the drive chain. 2 P. 67● Place your vehicle on a maintenance stand
and position a block so that both tires areoff the ground.
● After rain, remove the body cover and allowthe vehicle to dry.
● Remove the battery (2 P. 72) to preventdischarge. Fully charge the battery and thenplace it in a shaded, well-ventilated area.u If you leave the battery in place,
disconnect the negative - terminal toprevent discharge.
Storing Your Vehicle
Information
114
After removing your vehicle from storage,inspect all maintenance items required by theMaintenance Schedule.
USA For more information about storage, referto the Honda Winter Storage Guide, availablefrom your dealer.
Canada For more information about storage,visit our website at www.honda.ca and look up“Storage Tips” under the “Honda Warranty” inthe Warranty tab for your Model.
Transporting Your VehicleIf your vehicle needs to be transported, itshould be carried on a motorcycle trailer or aflatbed truck or trailer that has a loading rampor lifting platform, and motorcycle tie-downstraps. Never try to tow your vehicle with awheel or wheels on the ground.
NOTICETowing your vehicle with a wheel or wheels onthe ground can cause serious damage to thetransmission.
Transporting Your VehicleInform
ation
115
You & the EnvironmentOwning and riding a vehicle can be enjoyable,but you must do your part to protect theenvironment.
Choose Sensible CleanersUse a biodegradable detergent when you washyour vehicle. Avoid aerosol spray cleaners thatcontain chlorofluorocarbons (CFCs) whichdamage the atmosphere's protective ozonelayer.
Recycle WastesPut oil and other toxic wastes in approvedcontainers and take them to a recycling center.Call your local or state office of public works orenvironmental services to find a recycling centerin your area, and to get instructions on how todispose of non-recyclable wastes. Do not placeused engine oil in the trash, or pour it down adrain or on the ground. Used oil, gasoline,coolant, and cleaning solvents contain poisonsthat can hurt refuse workers and contaminatedrinking water, lakes, rivers, and oceans.
You & the Environment
Information
116
Vehicle IdentificationNumberThe VIN and engine serial number uniquelyidentify your vehicle and are required in orderto register your vehicle. They may also berequired when ordering replacement parts.You should record these numbers and keepthem in a safe place.
Vehicle Identification NumberInform
ation
117
VIN
VIN
Engine number
Emission Control SystemsYour vehicle engine emits combustionbyproducts, including carbon monoxide (CO),oxides of nitrogen (NOx), and hydrocarbons(HC). Gasoline evaporation also emitshydrocarbons. Controlling the production ofNOx, CO, and HC is important for theenvironment.
Exhaust Emission RequirementsThe U.S. Environmental Protection Agency(EPA), the California Air Resources Board(CARB), and Environment and Climate ChangeCanada (ECCC) require that your vehicle complywith applicable exhaust, crankcase, and fuelpermeation emission standards during its usefullife, when operated and maintained accordingto the instructions provided.CARB also requires that your vehicle complywith applicable evaporative emissionrequirements during its useful life, when
operated and maintained according to theinstructions provided.USA Compliance with the terms of theDistributor's Warranties for Honda MotorcycleEmission Control Systems is necessary in orderto maintain a valid emissions system warranty.The Vehicle Emission Control Information labelis attached to the rear fender.
Emission Control Systems
Information
118
Vehicle emission controlinformation label
Canada
Vehicle emission controlinformation label
Noise Emission RequirementsThe EPA requires that vehicles built afterJanuary 1, 1983 comply with applicable noiseemission standards for one year or 3,730 miles(6,000 km) after the time of purchase whenoperated and maintained according to theinstructions provided.
Exhaust Emission Control SystemThe exhaust emission control system includesthe following components that should not needadjustment, although periodic inspection byyour dealer is recommended.
# PGM-FI SystemThe PGM-FI (programmed fuel injection) systemuses sequential multiport fuel injection, and iscomprised of air intake, engine control, fuelcontrol, and exhaust control subsystems. Theengine control module (ECM) uses sensors todetermine how much air enters the engine, andthen controls how much fuel to inject.
# Ignition Timing Control SystemThe ignition timing control system adjusts theignition timing to reduce the amount of HC,CO, and NOx produced.
# Secondary Air Injection SystemThe secondary air injection system adds filteredair into the exhaust gas to help improveemission control performance.
# Catalytic ConvertersThe exhaust system contains one or morecatalytic converters. Catalytic converters use acatalyst to convert most of the harmful exhaustgas compounds into harmless compounds.
Emission Control SystemsInform
ation
119Continued
Evaporative Emission Control System50 STATE (meets California)An evaporative emissions control system uses acanister filled with charcoal to adsorb fuel vaporfrom the fuel tank while the engine is off. Thevapor is drawn into the engine and burnedwhile riding.
Crankcase Emissions Control SystemThe engine is equipped with a closed crankcasesystem to prevent discharging crankcaseemissions into the atmosphere.Blow-by gas is returned to the combustionchamber through the air cleaner and throttlebody.
Fuel Permeation Emission ControlThe fuel tank, fuel hoses, and fuel vapor chargehoses use fuel permeation control technologiesto prevent fuel vapor emissions. Tampering withthese components to reduce or defeat the
effectiveness of the fuel permeationtechnologies is prohibited.
Noise Emission Control System
# TAMPERING WITH THE NOISE CONTROLSYSTEM IS PROHIBITED:
U. S. federal law prohibits, and Canadianprovincial laws may prohibit, the following actsor the causing thereof: (1) The removal orrendering inoperative by any person, other thanfor purposes of maintenance, repair orreplacement, of any device or element ofdesign incorporated into any new vehicle forthe purpose of noise control prior to its sale ordelivery to the ultimate purchaser or while it isin use; or (2) the use of the vehicle after suchdevice or element of design has been removedor rendered inoperative by any person.
Emission Control Systems
Information
120
# AMONG THOSE ACTS PRESUMED TOCONSTITUTE TAMPERING ARE THEFOLLOWING ACTS:● Removal of, or puncturing the muffler,
baffles, header pipes or any othercomponent which conducts exhaust gases.
● Removal of, or puncturing of any part of theintake system.
● Lack of proper maintenance.● Removing or disabling any emissions
compliance component, or replacing anycompliance component with a noncompliantcomponent.
Problems Affecting Vehicle ExhaustEmissions
Have your vehicle inspected and repaired byyour dealer if you experience any of thefollowing symptoms:● Hard starting or stalling after starting● Rough idling● Misfiring or backfiring during acceleration● Poor engine performance and poor fuel
economy
Emission Control SystemsInform
ation
121
Catalytic ConverterThis vehicle is equipped with a three-waycatalytic converter. The catalytic convertercontains precious metals that serve as catalystsin high temperature chemical reactions thatconvert hydrocarbons (HC), carbon monoxide(CO), and oxides of nitrogen (NOx) in theexhaust gasses into safe compounds.
A defective catalytic converter contributes to airpollution and can impair your engine'sperformance. A replacement unit must be anoriginal Honda part or equivalent.
Follow these guidelines to protect your vehicle'scatalytic converter.● Always use unleaded gasoline. Leaded
gasoline will damage the catalytic converter.● Keep the engine in good running condition.
A poorly running engine can cause thecatalytic converter to overheat causingdamage to the converter or the vehicle.
● If your engine is misfiring, backfiring, stalling,or otherwise not running properly, stopriding and turn off the engine. Have yourvehicle serviced as soon as possible.
Catalytic Converter
Information
122
Oxygenated FuelsSome conventional fuels blended with alcoholor an ether compound are available in somelocales to help reduce emissions to meet cleanair standards. These gasolines are collectivelyreferred to as oxygenated fuels. If you plan touse oxygenated fuel, check that it is unleadedand meets the minimum octane rating andblend requirement.
The following fuel blends have been approvedfor use in your vehicle:● Ethanol (ethyl alcohol) up to 10% by volume.
u Gasoline containing ethanol may bemarketed under the name Gasohol.
● Do not use gasoline containing methanol(methyl alcohol).
If you accidentally fill your fuel tank with anoxygenated fuel containing higher percentages,you may experience performance problems. Toresolve the problem, have your dealer drain thefuel tank and replace with the correct fuel. Fuelsystem or performance problems resulting fromthe use of an oxygenated fuel containing higherpercentages are not covered by your warranty.
NOTICEImproper use of oxygenated fuels can damagemetal, rubber, and plastic parts of your fuelsystem.Oxygenated fuel can also damage paint.Damage caused by spilled fuel is not covered bywarranty.
If you notice any undesirable operatingsymptoms or performance problems, try adifferent brand of gasoline.
Oxygenated FuelsInform
ation
123
Description2021 CRF300L/LA/LR/LRA Service ManualCommon Service Manual (61CSM00)USA Winter Storage Guide (S9507)2021 CRF300L/LA Owner’s Manual
Authorized ManualsUSA The Service Manual used by your authorizeddealer is available from your Honda dealer or Helm,Inc. Canada See your dealer to order authorized manuals.
Also available, but not necessary to service yourmodel, is the Honda Common Service Manual, whichexplains basic service information for various systemson Honda motorcycles, scooters, ATV, and SxS.USA The Winter Storage Guide in conjunction withthe Owner's Manual and Service Manual can helpyou prepare your Honda motorcycle, scooter, ATV,and SxS for winter storage.
These Honda manuals are written for the professionaltechnician. However, if you possess the proper tools,observe the safety standards, and are mechanicallycapable, you should find them easy to use.Special Honda tools are necessary for someprocedures.
USAOrder online: www.helminc.com
Order Toll Free: 1-888-CYCLE93 (1-888-292-5393) (NOTE: For Credit Card Orders Only) Monday - Friday 8:00 AM - 6:00 PM EST
Authorized Manuals
Information
124
Warranty Coverage andServiceCoverage
Your new Honda is covered by the followingwarranties:● Vehicle Limited Warranty● Emission Control System Warranty● USA Noise Control Warranty
The responsibilities, restrictions, and exclusionsthat apply to these warranties are explained inthe Warranties Booklet given to you by yourHonda dealer at the time of purchase. Alwayskeep your Honda owner's card with yourWarranties Booklet.Canada Please refer to the Warranty Bookletposted on our website at www.honda.ca.
It is important to realize that your warrantyapplies only to defects in material orworkmanship of your Honda. Your warranty
coverage does not apply to the normal wearand deterioration associated with use of thevehicle.
Your warranty coverage is not voided if youperform your own maintenance. However,failures that occur due directly to impropermaintenance are not covered by thesewarranties.
USA You can extend almost all of your warrantycoverage through the Honda Protection Plan.For more information, see your Honda dealer.
Warranty Coverage and ServiceInform
ation
125Continued
Statement on Warranty Coverage forAftermarket and Recycled PartsNew JerseyThe Magnuson-Moss Warranty Act, 15 U.S.C. s.2301 et seq., makes it illegal for motor vehiclemanufacturers to void a motor vehicle warrantyor deny warranty coverage solely because anaftermarket or recycled part has been used torepair the vehicle or someone other than theauthorized service provider performed serviceon the vehicle. This provision does not apply toa new motor vehicle purchased solely forcommercial or industrial use.Under federal law, a manufacturer may denywarranty coverage and charge for repairs to avehicle if it is discovered that an aftermarket orrecycled part installed on the vehicle is defectiveor was installed incorrectly and caused damageto another part of the vehicle otherwise coveredunder warranty. The Federal Trade Commissionrequires that a manufacturer demonstrate thatan aftermarket or recycled part or service
performed by a person other than anauthorized service provider caused damage toanother part of the vehicle otherwise coveredunder warranty before denying warrantycoverage. Additionally, federal law allows amanufacturer to void a motor vehicle warrantyor deny warranty coverage if the manufacturerprovides the article or service to consumers freeof charge under the warranty or themanufacturer has secured a waiver from theFederal Trade Commission.
Warranty Coverage and Service
Information
126
ServicePlease remember that maintenancerecommended in the Maintenance Schedule isnot included in your warranty coverage.
If you believe you have a problem with yourvehicle, call the service department of yourHonda dealer. Make an appointment for aninspection and diagnosis. You will be asked toauthorize that inspection, and your dealer willreturn the results of the inspection. If a problemexists and is covered under warranty, yourdealer will perform the warranty repairs. If youhave any questions about your warrantycoverage or the nature of the repair, talk to theService Manager of your Honda dealer.
If a misunderstanding occurs and you aren'tsatisfied with your dealer's handling of thesituation, we suggest you discuss your problemwith the appropriate member of thedealership's management team. If you are still
not satisfied, contact the owner of thedealership or their designated representative.
Warranty Coverage and ServiceInform
ation
127
Honda ContactsAmerican Honda Motor Co., Inc.
If you wish to contact Honda directly tocomment on your experiences with your vehicleor with your dealer, please send your commentsto the following address:
Powersports Customer RelationsAmerican Honda Motor Co., Inc., P.O. Box 2200, Torrance, CA 90509-2200Mailstop: 100-4W-5F, Telephone: (866) 784-1870Website: https://powersports.honda.com/contact-us
CanadaHonda Canada Inc.Customer Relations Department,180 Honda BoulevardMarkham, Ontario L6C 0H9Telephone: (888) 946-6329Fax: (877) 939-0909E-mail: [email protected] include the following information in yourletter:● Name, address, and telephone number● Product model, year, and VIN● Date of purchase● Dealer name and address
We will likely ask your Honda dealer to respond,or possibly acknowledge your commentsdirectly.
Honda Contacts
Information
128
Your Honda DealerThe service department of your Honda dealeroffers trained personnel to perform regularmaintenance and unexpected repairs. It has thelatest available service information from Hondaand also handles warranty inspections andrepairs.
The parts department offers Honda GenuineParts, Pro Honda products, Honda GenuineAccessories (USA only), and Honda accessoriesand products (Canada only) that provide thesame quality that went into your vehicle.
USA The sales department offers the HondaProtection Plan to extend almost all of yourwarranty coverage.
Your Honda dealer can also supply informationabout, riding events, and information aboutsafety training available in your local area.
Honda ContactsInform
ation
129
Reporting Safety DefectsUSAIf you believe that your vehicle has adefect which could cause a crash orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in addition tonotifying American Honda Motor Co.,Inc.
If NHTSA receives similar complaints, itmay open an investigation, and if itfinds that a safety defect exists in agroup of vehicles, it may order a recalland remedy campaign. However,NHTSA cannot become involved inindividual problems between you, your
dealer, or American Honda Motor Co.,Inc.
To contact NHTSA, you may call theVehicle Safety Hotline toll-free at:1-888-327-4236(TTY: 1-800-424-9153); go tohttp://www.safercar.gov;or write to:Administrator, NHTSA,1200 New Jersey Avenue, SE.,Washington, DC 20590.You can also obtain other informationabout motor vehicle safety from:http://www.safercar.gov.
Reporting Safety Defects
Information
130
CanadaIf you believe that your vehicle has adefect which could cause a crash orcould cause injury or death, youshould immediately inform HondaCanada Inc. and you may also informTransport Canada.
If Transport Canada receives similarcomplaints, it may open aninvestigation, and if it finds that asafety defect exists in a group ofvehicles, it may lead to a recall andremedy campaign. However, TransportCanada cannot become involved inindividual problems between you, yourdealer, or Honda Canada Inc.
To contact Transport Canada’s DefectInvestigations and Recalls Division, youmay call:1-800-333-0510For more information on reportingsafety defects or about motor vehiclesafety, go tohttp://www.tc.gc.ca/roadsafety.
Reporting Safety DefectsInform
ation
131
Specifications■ Main ComponentsOverall length 87.8 in (2,230 mm)Overall width 32.3 in (820 mm)Overall height 47.2 in (1,200 mm)Wheelbase 57.3 in (1,455 mm)Minimum groundclearance 11.2 in (285 mm)
Caster angle 27.5°Trail 4.3 in (109 mm)
Curb weight CRF300L 306 lb (139 kg)CRF300LA 311 lb (141 kg)
Maximum weightcapacity *1
50 STATE (meets California) 326 lb (148 kg)Canada 320 lb (145 kg)
Passenger capacity Rider and 1 passengerMinimum turningradius 7.5 ft (2.3 m)
Displacement 17.4 cu-in (286 cm3)Bore x stroke 2.99 x 2.48 in (76.0 x 63.0 mm)Compression ratio 10.7:1
Fuel Unleaded gasolineRecommended: 86 PON or higher
Tank capacity 2.06 US gal (7.8 L)
Battery YTZ8V12 V-7.0 Ah (10 HR)
Gear ratio
1st 3.5382nd 2.2503rd 1.6504th 1.3465th 1.1156th 0.925
Reduction ratio(primary / final) 2.807 / 2.857
*1 : Including rider, passenger, all luggage, and accessories.
Specifications
132
■ Service DataTire size Front 80/100-21M/C (51P)
Rear 120/80-18M/C (62P)Tire type Bias-ply, tubeRecommendedTire
Front IRC GP-21FRear IRC GP-22R
Tire air pressure Up to 90 kg (200lbs) load
Front 22 psi (150 kPa, 1.50 kgf/cm2)Rear 22 psi (150 kPa, 1.50 kgf/cm2)
Tire air pressure Up to Maximumweight capacity
Front 22 psi (150 kPa, 1.50 kgf/cm2)Rear 25 psi (175 kPa, 1.75 kgf/cm2)
Minimum treaddepth
Front 0.12 in (3.0 mm)Rear 0.12 in (3.0 mm)
Spark plug (standard) SIMR8A9 (NGK)
Spark plug gap (non-adjustable) 0.03 - 0.04 in (0.8 - 0.9 mm)
Idle speed (non-adjustable) 1,450 ± 100 rpm
Recommendedengine oil
Honda 4-stroke motorcycle oil API ServiceClassification SG or higher, excluding oilsmarked as “Energy Conserving” or“Resource Conserving” SAE 10W-30, JASO T903 standard MA
Engine oilcapacity
Afterdraining 1.5 US qt (1.4 L)
Afterdraining &filterchange
1.6 US qt (1.5 L)
Afterdisassembly 1.9 US qt (1.8 L)
Recommendedbrake fluid Honda DOT 3 or DOT 4 Brake Fluid
Cooling systemcapacity 0.91 US qt (0.86 L)
Recommendedcoolant Pro Honda HP Coolant
Drive chain slack 2 - 2 1/4 in (50 - 55 mm)Recommendeddrive chainlubricant
Pro Honda HP Chain Lube or equivalent
Standard drivechain
DID 520VFNo. of links 106
Standard sprocketsize
Drivesprocket 14T
Drivensprocket 40T
SpecificationsSpecifications
133
■ BulbsHeadlight 12 V-60 / 55 WBrake light / Taillight 12 V-21 / 5 WFront turn signal / Positionlight 12 V-21 / 5 W x 2
Rear turn signal 12 V-21 W x 2License plate light LED
■ FusesMain fuse 30 A
Other fuse CRF300L 10 ACRF300LA 30 A, 10 A
■ Torque SpecificationsHook bolt 15 lbf·ft (21 N·m, 2.1 kgf·m)Tail cap cover screw 3.9 lbf·ft (5.25 N·m, 0.5 kgf·m)Spark arrester mounting bolt 6.6 lbf·ft (9.0 N·m, 0.9 kgf·m)
Specifications
Specifications
134
Information Record
VINEngine No.Color Label & CodeOwner's Name
AddressCity/StatePhone
Dealer's NameAddressCity/StatePhoneService Manager
135
California Proposition 65 WarningWARNING: Operating, servicing and maintaining a passenger
vehicle or off-highway motor vehicle can expose you to chemicalsincluding engine exhaust, carbon monoxide, phthalates, and lead,which are known to the State of California to cause cancer and birthdefects or other reproductive harm. To minimize exposure, avoidbreathing exhaust, do not idle the engine except as necessary, serviceyour vehicle in a well-ventilated area and wear gloves or wash yourhands frequently when servicing your vehicle. For more information gotowww.P65Warnings.ca.gov/passenger-vehicle.
00X31-K1T-A00031K1TA00
PRINTED IN USA